Budget renovation of a bathroom in a private house. Finishing a bathroom in a wooden house Ideas for a bathroom in a private house

It is difficult to imagine a modern home without such already familiar amenities as a bathroom and a bathroom. It doesn’t matter if the bathroom is located in a private house outside the city or in an apartment, in any case, the creation of its design must be approached responsibly. Properly selected colors and thoughtful interior will provide a relaxing atmosphere where it is nice to find yourself after a hard day. Of great importance is also correct selection materials, as they must be resistant to moisture. In today's article, we will learn how to make a beautiful bathroom design in a private house, and also look at interesting options design in the photo selection below.

Bathroom in a private house - layout of the room

The big advantage of a private house, compared to an apartment, is that it is possible to set the dimensions of the bathroom on your own, as well as place it in any part of the house. This significant advantage allows you to implement the most daring design solutions and equip the bathroom with additional accessories.

Whether you're building a house from the ground up, or just looking to redecorate your existing bathroom, the amount and extent of prep work required varies.

With new construction, even at the stage of creating a design project, it is worth deciding on the location of the bathroom. This is necessary in order to immediately carry out the necessary communications during the construction process, such as water supply and sewerage, as well as perform waterproofing. At the next stage of construction, a ventilation system is created. Provided that the exhaust system is done correctly, this approach will eliminate unpleasant odors relatively quickly, reduce humidity and minimize the destructive effect of moisture on the finish of the room. When the above steps have been completed, then proceed to decorative trim premises. Often a bathroom in a private house has enough large area, which gives an opportunity for creativity in planning and decorating the room.

If you are planning to renovate an existing bathroom, then this will require much less effort and investment. Main preparatory actions includes dismantling of the old plumbing equipment, as well as floor, wall and ceiling finishes. In order to better navigate current trends design, we offer you to look at the photos of bathrooms in private houses, presented below.

Installing a window in a private bathroom

The main advantage of installing a window in the bathroom is the additional possibility of airing the room. Even with an exhaust system, an open window will help to get rid of the steam much faster after taking a bath. Another plus is the increase in the level of natural light, which saves money on lighting during daylight hours. In addition, often a window sill is mounted under the window, on which several decorative elements can be placed. If your house is located in a picturesque place, then another nice bonus will be a beautiful view from the window. See how the windows of the bathroom in a private house are originally inscribed in its design in the photo selection below.

Beautiful design of bathrooms in private houses: photo of finishing ideas

Before proceeding with the direct finishing of the bathroom, it is necessary to insulate the walls and floor. These actions will help to avoid the formation of a large amount of condensate, and therefore fungus with mold in the future.

Since the bathroom in a private house is a “wet” room, the most moisture-resistant materials should be used for its decoration, of which, today, there are a large number. All these materials have their advantages and disadvantages, and of course, they differ in price. If you are thinking about how to make a bathroom in a private house fashionable and modern, then you need to know what finishing materials are the most popular today.

Ceramic tile for bathroom

This material is recognized as the most popular today, because it has many positive characteristics. This is an excellent moisture resistance, resistance to damage, as well as a huge variety of color and texture solutions. All these advantages allow you to create interiors in almost any style, it all depends on your imagination and financial capabilities.

Plastic bathroom panels

Plastic panels are the cheapest way to finish a bathroom, which is perfect for giving. The advantage of this finish can be called a large selection of colors and sizes. The main disadvantage is that the panels are easily damaged.

wall painting

Wall painting is easy to create a very original design, combining different shades or using special stencils for decoration. Before painting, the walls must be plastered and primed. Only after preparation, a special moisture-resistant paint is applied to the walls.

natural wood

Finishing the bathroom with natural wood will make it stylish and very comfortable. For such a finish, you need to use only moisture-resistant wood species, as well as additionally treat them with special means to protect against moisture.

Wallpaper in the bathroom

To finish the bathroom, you can use special moisture resistant wallpaper. However, in places where there is direct exposure to water, it is better to combine with another, more moisture resistant material, such as ceramic tiles.

Until recently, it was impossible to make a bathroom in a wooden house. high humidity and heat air in a very short time rendered any repair unusable. But today, a variety of modern building materials have made this problem not so relevant. Information on how to properly equip a bathroom in a wooden house, what materials allow you to repair work quickly and efficiently, it will be very useful for those who set out to have in a private house made of wood such a boon of civilization as a bathroom.

Arrangement of a water supply

The choice of how to drain water from the bathroom is of particular importance when it comes to the fact that the house is built of wooden beam. The fact is that a log cabin gives enough big shrinkage. This feature must be taken into account when designing and installing a plumbing system.

For these purposes, it is better to use metal-plastic pipes, as they are the most resistant to deformation. The laid pipeline must be fixed with special rubberized clips or clamps for plumbing elements. Also, do not forget about the protection of the pipeline from low temperatures. For this purpose, heat-insulating material is used, which covers not only pipes, but also the base of the floor in the bathroom.

Wood surfaces do not tolerate moisture very well - this is a fact. In order to protect the bathroom floor from premature damage, it is worthwhile to provide for the installation of a special drain valve, which will allow the accumulated moisture to drain into the sewer.

The best system for draining water in a wooden house is a drain ladder with a dry shutter. It is a plastic float that closes the drain hole after water is drained. Such a device is the most in the best way suitable for a bathroom in a wooden house in the country. It perfectly protects not only from the accumulation of excess moisture, but also from the penetration of unpleasant odors from the sewer into the interior.

Attention ! Assuming the presence of such a drain in the bathroom, the floor is laid at a slight slope.

Bathroom waterproofing

To prevent moisture from the bathroom from penetrating into the living quarters wooden house, it is imperative to carry out waterproofing work, thereby creating a certain protective barrier against steam and moisture.

Waterproofing a bathroom in a wooden house requires compliance with certain rules. Before you start finishing the bathroom with waterproofing materials, the walls, ceiling, and floor must be cleaned and leveled.

The best protection against moisture is provided by roofing material, liquid glass and self-leveling polymer floors. Installation of waterproofing of the floor and ceiling of the bathroom in a wooden house should be carried out in one go.

Consider the two most popular ways to waterproof a room in a wooden house:

1. Surface treatment with special moisture-proof mixtures, which, after drying, form a durable, waterproof film;
2. Installation of rolled material, forming a durable waterproofing layer. To prevent moisture from seeping through the seams of the material laid in rows, the sheets should be overlapped.

Attention ! If used as waterproofing polyethylene film, it is laid in several layers over the entire area of ​​\u200b\u200bthe room.

Waterproofing the bathroom floor wood flooring covered with a fairly dense layer bituminous mastic on which is placed waterproofing material. It is imperative to know that the main condition for conducting waterproofing works in the bathroom is that the floor level in this room should be lower than in other rooms.

After the waterproofing is laid, if necessary, a reinforcing mesh is laid, which is covered with insulation. The final stage is the pouring of the cement concrete screed.

All work is quite realistic to do on their own. The main thing is not to rush and strictly adhere to the algorithm of the work.

Bathroom ventilation

by the most best solution arrangement of ventilation for a bathroom in a wooden house will be installation supply and exhaust system. The installation technology is quite simple and quite affordable for independent execution.

Consider a step-by-step instruction for arranging ventilation in the bathroom:

1. Along the perimeter of the base of the future ceiling, two air pipes are mounted, one of which provides air inflow, and the other - its output.
2. In each pipe, special funnels are made in the corners of the bathroom, in one of which a fan will be installed in the future, and the second is closed with a decorative grille.

There are no special subtleties in the work, the main thing is to do everything carefully and clearly follow the prescribed plan.

Floor finish

Wood in its structure, of course, differs from brick or concrete blocks. Therefore, the decoration of the bathroom in a wooden house has its own specifics. It must be understood that the weight of plumbing elements is not constant. For example, a bathtub filled with water changes its mass, and the load on the floors of the house changes accordingly. Even if the bath is located on the first floor, such differences in loads can affect the integrity and density of wooden floors.

In order to avoid a fairly rapid destruction of the house, it is necessary to provide for the following nuances at the design stage:

• the thickness of the floors is increased by 25%;
• cross-sectional area increases bearing beams;
• installation of beams is carried out with a smaller step and at a level of 20 cm below normal.

These conditions are mandatory, since the bathroom floor in a wooden house, in addition to a concrete screed and a waterproofing layer, is tiled. If you do not take into account the necessary parameters for laying load-bearing beams and floors, then you can get a discrepancy between the floor level of the bathroom and other living quarters.

As a floor covering, in addition to ceramic tiles, you can use linoleum, moisture-resistant laminate, especially durable woods, cork or mosaics.

wall decoration

When thinking about how to sheathe a bathroom in a wooden house, it is worth considering the specifics of building a house and the characteristic features of the main building material - wood. It is important to remember that constant temperature changes, high humidity greatly affects the structure of wood. It can dry out or, on the contrary, crack, gaining moisture.

All this leads to quite serious troubles, in the form of deformation of the walls and distortion of the geometry of the entire room. To avoid such moments, before you start finishing the wooden walls of the bathroom, a protective false wall is attached to them, and only then the finishing material.

Drywall is well suited as a base for decor. False walls mounted from such material are perfect for any finish. The only exception when the walls can not be sheathed with plasterboard is lining the walls with clapboard.

Very often an independent structure on a special moving frame is used. For this, a metal profile is used, which is fixed with movable connectors to the wall. This method It is very relevant for finishing wooden walls, since when the main structure shrinks, only wooden walls move, and the lined surface remains indestructible.

Important ! When mounting false walls, do not forget about the presence of a certain air gap between the wooden walls and the mounted veneered surface. It is necessary for natural ventilation and prevents condensation.

A good option would be to finish the wooden walls of the bathroom in a combined way. It provides for wall decoration with ceramic tiles in places closest to the water, and other finishing materials in the remaining area. You can combine materials in a variety of planes. Alternate the decor from the ceiling to the middle of the wall, and then to the floor. Or combine several finishing materials on the two halves of the wall.

When choosing materials for finishing a bathroom in a wooden house, it is necessary to take into account indicators of resistance to moisture, chemical and household detergents. Traditionally used ceramic tile, mosaic, porcelain tile, lining. The option is not excluded when the walls remain in their original form, Only in this case they must be saturated with moisture. protective compounds.

The interior of a bathroom in a wooden house can be decorated in a wide variety of styles. The most advantageous look interiors in the style of Provence, classic, minimalism and eco-style.

Ceiling finish

The ceiling in the bathroom in a wooden house should have the following characteristics:

• do not let moisture through;
• be resistant to fire;
• absorb extraneous sounds;
• do not emit unpleasant odors and substances.

The best option that meets all the necessary requirements is stretch ceiling. In addition to excellent consumer qualities, it successfully hides all communications and it is possible to mount a sufficient number of ventilation holes in it.

The choice of style, color and texture of the ceiling in the bathroom is limited only by personal taste preferences and financial capabilities.

Bathroom lighting

Practical, modern and economical fixtures that are most suitable for a bathroom in a wooden house are halogen spotlights. They give good lighting over the entire surface, they are very convenient to mount at any point on the ceiling, thereby zoning the bathroom.

Important ! All wiring must be reliably protected from moisture.

The choice of plumbing

A responsible, but very pleasant stage, signaling that the repair work is at the finish line. For the bathroom of a wooden house, there are practically no restrictions on the installation of any plumbing equipment. Minimum set necessary elements consists of: a washbasin, a bathtub or shower cubicle, a toilet bowl (if the bathroom is combined). When choosing plumbing elements, only their mass should be taken into account, since large loads on the wooden floors of the house are undesirable.

Conclusion

Today, the presence of a bathroom in a wooden house is not a luxury, it is a prerequisite for a comfortable stay. For its arrangement, you do not need to overcome super-difficult tasks. It is enough to adhere to a clear sequence of work, not to rush, control the quality of the materials used and take into account their compatibility with the main material for building a house - wood.

We will learn more about how to decorate a bathroom in a wooden house in the next video.

One of the most milestones the arrangement of a residential building is the equipment in it of a bathroom. Considering that the regime of high humidity can negatively affect the construction of wood, for a house made of timber or logs, you will need to plan the implementation of these works in advance. Thus, choosing suitable option bathroom devices, using moisture-resistant materials and waterproofing the floor and ceiling, you can avoid many problems. For further arrangement of this room, you will need to choose a suitable beautiful and practical finish.

It's no secret that wooden structures under the influence of high humidity, they can swell, dry out and warp, are prone to the appearance of fungus or mold. Not so long ago, the arrangement of a bathroom in a house built of wood (logs or timber) was a real problem, because the presence of moisture and dampness in it was largely reflected in the microclimate of the entire building. Thanks to the development modern technologies, any homeowner can arrange a comfortable and functional bathroom in a wooden house with their own hands.

If you want to install a bathtub in a house made of timber or logs, you should take into account its significant weight, which is about 200 kg on average (besides, if you fill it with water, it can double). Protect yourself from possible problems it is possible by reinforcing the structures of a wooden house - in this case, the significant weight of the bathtub filled with water will not be an excessive load on the floors of the building. Taking into account the peculiarities of the operation of wood structures, it is advisable to plan how to properly make a bathroom in a wooden house, preferably starting from its construction. The design load on the floors in this case should be increased from the standard one to at least 460 kg / m 2. To do this, it is necessary to use beams of a larger section, as well as lay them with a smaller step. In addition, their level must be lowered by at least 0.1 m.

When planning a bathroom in a wooden house, it should also be taken into account that it is necessary to provide for a floor level 20-25 cm lower than in neighboring rooms. As a result of subsequent screeding and laying tiles, the floor level difference will be smoothed out.

To equip a bathroom in a wooden house, it is necessary to implement the following stages of work:

• provide a high-quality ventilation system;
• equip the sewer system and drainage system;
• execute reliable waterproofing premises;
• install plumbing in the bathroom;
• carry out finishing work.

Careful implementation of such work will make the further operation of the bathroom in a wooden house quite comfortable. By paying due attention to each of the above steps, you can greatly reduce the need for repairs and any rework in the near future.

Arrangement of a water supply

Of particular importance in a wooden house is the method of removal from the bathroom. As a rule, a house made of logs or timber gives a noticeable shrinkage. This feature wood should be taken into account when installing plumbing. To drain water, pipes that are resistant to deformation should be used - plastic or metal-plastic is suitable for this purpose. The pipeline must be fixed with special clips or clamps for plumbing pipes with rubber gaskets. You can protect the pipeline from winter frosts by insulating the pipes, as well as the base of the floor. In addition, in order to protect the wood in the bathroom from getting wet, it will be necessary to equip a drain valve through which water accumulating on the floor will be discharged from the room into the sewer.

Experts recommend paying attention to the drain drain system with a dry shutter, which is used as a plastic float that closes the hole after removing excess moisture. This device the drain is optimally suited for a private house, allowing you to protect residents from the penetration of unpleasant odors from the sewer. To equip such a drain, you will need to lay the floor in the bathroom at an angle of 1.5 °.

For the bathroom of a wooden house there are no restrictions on the installation of any plumbing equipment. Bathtubs of various sizes, shower cabins, Jacuzzi, etc. can be installed in this room.

Installation of the ventilation system

Regardless of the choice of materials for finishing the room, it is necessary to ensure full ventilation in the bathroom of a wooden house. To do this, you need to equip the bathroom with a sufficiently powerful system. forced ventilation. It should be brought to the attic of the house or laid under a false ceiling. It should be noted that in order to fire safety in a wooden house must be used non-combustible materials for equipment ventilation ducts, as well as a high-quality fan, protected from fire. In addition, all ventilation system be equipped with fire dampers. Fan power should be selected based on the size of the bathroom.

You can equip the ventilation in the bathroom as follows:

• lay two air ducts under the ceiling, providing air flow and its removal. To do this, outlets should be made from pipes in different corners of the bathroom;
• at their ends, in accordance with the planned level false ceiling, it is necessary to install funnels. In one of them, after installing it, you will need to mount a fan, the other should be decorated with a decorative grille.

Waterproofing the floor and ceiling with their subsequent finishing

To equip a bathroom in a wooden house, you will need to waterproof the room, creating an effective waterproof barrier. Particular attention when planning how to make a bathroom in a wooden house should be given to waterproofing the floor and ceiling. It is worth considering that before carrying out such work, it is necessary to clean and level the surface to be treated.

To ensure the waterproofing of the bathroom in a wooden house, you can use roofing material, liquid glass with a concrete screed, self-leveling polymer floors. It should be noted that the waterproofing of the floor and ceiling in this room must be carried out simultaneously.

There are two main ways to waterproof a bathroom in a wooden house with your own hands:

• applying a waterproofing mixture to the surface, creating a film impervious to moisture;
• pasting the surface with a layer of rolled material that protects against moisture (it should be overlapped).

When using a film waterproofing material, it is usually laid in two layers on the floor around the entire perimeter of the room, also overlapping the surface of the walls to a height of at least 0.1-0.2 m.

To impart moisture resistance, the surface of wooden walls should be treated with special antiseptic protective compounds. In the bathroom of a wooden house, you can install false ceiling- this design will hide the ventilation system, moreover, in this way it is easy to organize effective lighting of the room. as more available option ceiling lining can be done tiles.

To waterproof the floor in the bathroom, a layer of bituminous mastic can be laid on a wooden flooring and a rolled waterproofing material like Aquaizola on top. When carrying out work, it should be taken into account that as important condition the waterproofing of the bathroom floor is a level difference - it is required that in this room it be lower relative to other rooms.

If the waterproofing of the bathroom is done efficiently and reliably, the final floor covering can be done in almost any way. Most often, the following materials are used for laying the bathroom floor in a wooden house:

• moisture resistant types of laminate;
• linoleum;
• ceramic or porcelain tiles;
• adhesive cork coating;
• moisture resistant types of wood.

It is quite possible to perform these works on your own, while the small errors that have arisen are unlikely to be noticeable and in any way affect the beauty of the decoration of the room, in this case, the main thing is to carefully adhere to the technology for performing work.

Wall decoration in the bathroom

When decorating wooden walls in the bathroom, it is worth considering the characteristic features of working with this material. Due to its natural origin, under the influence of temperature and humidity fluctuations, wood is largely subject to drying out and shrinkage. To avoid possible problems in the form of wall deformation, before carrying out finishing works a crate should be installed on them - a false wall is subsequently attached to it and a cladding on top. It is easy to adapt the walls of a bathroom in a wooden house for subsequent finishing with the help of moisture resistant drywall. False walls built from this building material are suitable for almost any final bathroom finish in a wooden house. An exception is the situation if a decision is made to clad the walls wooden lath- in this case, it is not necessary to build false structures.

independent design for further finishing can be erected on a special sliding frame made of a metal profile. It is attached to the wall using movable joints in the form of vertical grooves with screws inserted into them - in case of any deformation of the main walls, it is they who move, and the lining is preserved in its original form. When constructing false walls, a ventilation gap between them and wooden walls should be observed.

The bathroom of a wooden house is easy to successfully arrange with the help of combined finishes walls - in this case, they are faced with wood, except for places that need to be protected from water ingress (near the placement of a bathroom, washbasin, etc.) In addition, you can finish the walls with tiles from below to a certain level of the walls. Lining materials should be selected taking into account their moisture resistance, in addition, their resistance to washing with household chemicals, as well as the ingress of aggressive chemicals on them, should be taken into account. To decorate the walls of this room, any moisture-resistant finish is suitable, including ceramic tiles or artistic mosaics, porcelain stoneware or lining. Wooden walls can also be left in their original form by treating them with a special impregnation to make the wood moisture resistant.

Owners wooden houses can arrange bathrooms in various styles. The most advantageous for this room are classic, country or provence, art deco, minimalist and eco-style.

Bathroom in a wooden house - photo

Bathroom in a wooden house - video

More recently, a bathroom in a wooden house was a rarity. This is due to the high humidity in such rooms. The results of any repair in wooden buildings in the presence of such conditions very quickly come to naught. Today, this problem is solved by the choice of appropriate building materials. It is important to know how to equip the bathroom, what materials will be needed for this, how to conduct water and equip the sewer system.

Requirements for a bathroom in a wooden house

To make it comfortable to be in the bathroom in a wooden house, and the room itself served the residents as long as possible, you should take care of proper waterproofing and insulation. It is important to equip the ventilation system of the room. Best for bathroom quality materials. This will extend the time until the next repair. First you need to create a project.

Important! Before arranging a bath, it is important to equip high-quality sewage. Water will drain into a septic tank or storage tank.

When designing a bathroom, the features of its installation are determined based on several important parameters - how many people live in the house and how many guests are planned. If the family is small, and consists of a maximum of 5 people, it will be enough to equip only one bathroom. The bathroom is usually combined if 3 people live in the house. With more people, the toilet is arranged in a separate room.

Advice! When arranging a bathroom in a wooden house, you should Special attention draw to the floor. This is due to the large mass of the bath.

Overlaps must be reinforced to prevent deformation. They are usually strengthened by increasing cross section beams, and reducing the distance between them. The floor level in the bathroom falls 10 cm below the floor level of the rest of the rooms. To create a floor, you will need to arrange a rough flooring, then lay a layer of waterproofing and pour a screed for the tiles. When designing the location of plumbing equipment, a plan should be drawn up for the placement of water and sewer pipes.

Creating a plumbing system

Considering that the house was built from a wooden beam, special attention should be paid to the way water is drained from the bathroom. This is due to the strong shrinkage of the log house. Installation and plumbing systems should take into account this feature of wooden buildings. For such purposes, pipes made of metal-plastic are often used. This is due to their resistance to deformation. The laid pipeline is necessarily fixed on clips or with clamps.

We should not forget about the protection of pipelines from the effects of low temperatures. For this it is necessary to use thermal insulation materials. They cover not only pipes, but also the base of the floor in the bathroom.

Wooden surfaces do not cope well with moisture. This fact is indisputable. To protect the wooden floor in the bathroom, it is necessary to foresee the installation of a drain valve. It will not allow excess moisture to linger in the room.

Optimum water drainage system wooden room is a drain with a dry seal. This part is a plastic float that blocks the drain hole after water is drained. When equipping a bathroom in a wooden house, this device is optimal. It can not only prevent the accumulation of water, but also eliminates the penetration of an unpleasant odor into the room from the sewer. This system must be installed in every bath.

Attention! When installing such a drain, the floor must be laid at a slope in its direction.

Water supply

First of all, it is important to correctly draw up a plumbing scheme. As soon as it is decided to equip a water supply system in a wooden house, its location in the house should be designed. It is important to take into account such elements as a pump, boiler, collectors and cleaning devices. Each part of the system should be reflected in the diagram. The pipe laying path must also be noted in the drawing of the house. It is better if the scheme takes into account the distances between each element of the system.

Pipes are laid in accordance with several schemes:

• sequentially;
• with collector connection.

When small buildings optimal serial connection type. At the same time, the number of residents using water will be quite small. If the bath is equipped in a country house for permanent residence, it is better not to install such a system. It works quite simply - water is transported through the main pipes, and a tee is mounted near each consumption point. This allows water to be diverted to consumers. When operating a water supply system at once by several consumers, the water pressure at the end will be the least.

When connecting a collector type, pipes are diverted from the source to each point separately. This allows you to maintain pressure throughout the entire plumbing. This method of installing pipes is chosen in the case of large houses.

When choosing a collector system, the cost of installing the entire plumbing system at home increases significantly. It's connected with large quantity communications to be purchased. However, the high operating comfort of such a system is worth the money. Therefore, it is better to deal with the collector wiring method in more detail.

Each water supply scheme includes the following details:

Water pipes at home may include other designs. However, the wiring diagram remains the same.

Pipe selection

In works that are associated with conducting communications in suburban buildings, the most difficult thing is to make holes in the floor or walls. The rest of the procedures, such as cutting and connecting pipes, are quite simple. In addition, you will need to connect the pipeline to the collector, install pump equipment and filtration systems. This explains why even a beginner can build a water pipe with his own hands.

First you need to figure out what materials it is better to buy pipes from:

The price of a plumbing system device depends not only on the number of pipes, but also on the material of their manufacture. Therefore, when buying, you should focus on the price / quality ratio.

The choice of the optimal pipe diameter is just as important as the choice of material. This is due to the peculiarities of the passage of water in the water supply. For example, if the pipes are too small in diameter, turbulence in the flow may occur. In this case, water will move through the pipes with noise, and lime deposits will accumulate inside them.

The diameter of the pipes depends on the total length of the pipeline:

• If the pipeline will have a total length of less than 30 m, it is better to choose a diameter of 25 mm.
• With a length water pipe exceeding 30 m, pipes with a diameter of 32 mm should be purchased.
• In the case of short pipelines with a length of less than 10 m, it is worth choosing products with a diameter of 20 mm.

To properly equip the water supply system in a country house made of wood, you should choose optimal diameter collector pipes. It is necessary for it to provide wide opportunities for the use of water by several consumers. There are several standard calculations by which the diameter of pipes is determined:

• With a pipe diameter of 25 mm, the product is able to pass about 30 l / min.
• In the case of a diameter of 32 mm, the pipe will be able to pass 50 l / min.
• If the pipe diameter is 38 mm, 75 l/min will flow through it.

When living in a house big family, and the presence of many water intake points in the house, situations often occur when they are used simultaneously. If you add up the volumes of water consumed by several appliances, you can get a pretty impressive number.

When a water supply system is arranged for a small family, and there are quite a lot of water consumers in the house, the calculation is performed according to a different rule. It is necessary to calculate how much water is consumed at several water intake points and reduce this figure by 25-40%. This figure will be an approximate family expense.

sewerage scheme

To the house from the well or septic tank to central system sewer pipe must be connected outdoor sewerage. It is connected to the outlet pipe. Then there are the supply pipes. They are connected to sinks, baths, washing machine. The connection is made using flexible corrugated pipes. Docking points should be sealed with sealant. The toilet bowl must be connected with a corrugated pipe to the outlet pipe coupling.

Branches that are not in use should be sealed with plugs. The outlet pipe between floors must be connected through a revision. Requirements for sewerage in a wooden house:

All the main indicators necessary for the calculation sewer system, can be taken from SNiP. This documentation describes how to build this system without violating various building and environmental regulations.

Bath waterproofing

So that from the room where water procedures will be carried out, moisture does not get into living rooms, it is necessary to create the correct waterproofing protection. This will extend the service life wooden elements building structures. Waterproofing measures must comply with certain rules. Before starting work, the surfaces to be waterproofed should be cleaned and leveled.

The optimal protection against moisture in a wooden house is roll material- ruberoid. Other means can be used - polymer floors and liquid glass. The waterproofing of the ceiling and floor in the bathroom is carried out in one working day.

There are several proven ways to waterproof a bathroom in a wooden house:

• Surfaces can be treated with various protective mixtures that form a durable and moisture-resistant film after hardening.
• Roll material laying. Due to this, you can create a fairly durable layer of waterproofing. Moisture must not get into the seams. To do this, the roll material is overlapped.

Attention! If a polyethylene film is chosen for waterproofing work, it must be laid in several layers.

Wooden flooring, which is already on the floor in a wooden house, should be covered with a layer of bitumen. Only when the mastic hardens, you can lay the waterproofing material. It is important to understand that the main condition for waterproofing work is to comply with a certain level of the finish floor, which should be obtained in the bathroom. It should be 10 cm lower than the rest of the floors in the house.

After laying the waterproofing, the insulation and reinforcing mesh should be laid. Then poured concrete screed. All work can be performed even by an inexperienced builder. The main rule that should be followed when doing all the work is do not rush. You also need to clearly follow all the stages of work.

Bathroom ventilation

The optimal solution when choosing ventilation for a bathroom in a wooden house is to install a supply and exhaust system. The installation work is pretty easy.

You should familiarize yourself with step by step instructions for ventilation installation:

• Along the perimeter of the base of the ceiling, you need to install two pipes through which air will be removed and supplied.
• Funnels are made in the corners of each pipe. In one of them, a fan is then mounted. The other will simply be covered with bars.

The work does not imply the presence of complexities and taking into account many subtleties. The basic principle is to strictly follow a pre-developed plan.

conclusions

Today, a bathroom in a country house in a wooden house is no longer such a rarity. This is due to the rich choice of building and finishing materials on the market. To equip a bath, you do not need to create complex schemes and waste a lot of time. The main work that will require full dedication and attention is the supply of water and the creation of a sewerage system. It will be enough to follow all the rules of work and a wooden house with a bathroom will last for many more decades.