A warm shower cabin with my own hands: how I built it in the country. Heated summer shower: do-it-yourself shower room for a summer cottage Do-it-yourself insulated summer shower in the country house

Outdoor shower, great to have it. And that would be enough if there was always
summer, and not just summer, but warm summer. And what to do when I went to the country for a week,
during the day 15-20 degrees, and frosts at night. In the morning, the water in the shower not only invigorates, but also
crooks teeth when you brush them. Either a walrus or a suicide is capable of rinsing with such water. Even a shower with heated water does not solve the problem, after it you have to run to the house. And summer is not all year round. Conclusion - do not ride in a cool
weather or build a shower in the house.
The house is a log house, ready to receive us in any weather. Check-in at the dacha begins early in the spring, and work on the hacienda is at sea. After a hard day, I want to wash off everything that stuck during the day, and preferably with warm water. We are already a people spoiled by urban amenities, and therefore country amenities also do not seem superfluous.
We decided to build a warm shower. The place was chosen on the first floor of the veranda. The veranda is not heated, but the entrance to the house is within easy reach. We decided to make a separate insulated room.
The walls were upholstered with clapboard with glass wool insulation and vapor barrier made of polyethylene film on both sides of the heater. Internal walls the shower room was covered with waterproof varnish in three layers.
storage tank, into which water is supplied by a pump from a well, is located on the second floor of the veranda. The difference between the levels of the floors is only 3 meters. I had to raise the tank above the floor to the maximum distance to ensure sufficient water pressure when using the shower.
In the shower room there are: a shower cabin with a 90x90 tray, a corner sink and a heating tank mounted on the wall. I made the main wiring of pipes on a shield attached to the wall of the log house.
It was decided to make a supply of cold water from polyethylene pipes. Metal plastic in the early 2000s still bit and was in few places. Metal-plastic made only a conclusion hot water from the heating tank to the shower mixer.
The pipe and all components were bought on Ryabinovaya Street in Moscow. There is also a free consultant on drafting the layout of the water supply system.
The pallet was installed with an inclination to the drain hole. The drain was made of a long polyethylene corrugated pipe no siphon. The drain pipe descends into the underground and through a hole in the foundation goes out into the street, where it ends with a barrel of rubble dug into the ground. It is crowded in the underground and even twice a year there is no desire to crawl through there to drain and twist the siphon, therefore I decided to abandon it.
And if you do not drain the water from the siphon in time, the frost will tear it apart. Pallet connected with drain pipe and checked for tightness, no drips. I installed the cabin, fixed the mixer. In the corner of the shower room, by the window, I fixed the corner sink of the washstand.
Let's move on to the split. I put a tap on the inlet pipe of the tank that shuts off the water supply, because. the same pump is used for other purposes. Water enters the tank through top entry.
The lower outlet from the tank leads to the heating tank and, bypassing it, to the shower faucet and washbasin. Before entering the water into the heating tank, I installed a tap so that water could be drained from it before leaving the dacha in the cold season. To do this, you just need to turn off the cold water, and open the outlet for hot water.
The water in it descends from the tank and two outlets of hot and cold water are connected to the tank, thereby excluding it from the water supply system. You can continue to use the taps.

Warm shower

Wiring diagram

DIY

The site was created in the uCoz system

We create a warm shower in the country: we find out the technical points

Of course, before you start building, you will have to make drawings of a warm shower in the country with your own hands in order to calculate all the materials, and besides, technical capabilities with which you are going to endow this structure.

Indeed, often heated water occurs in such buildings only in hot weather, that is, it is heated naturally, depending on weather conditions, but it can also be forced heating.

Country shower with heating

It's about this, forced way heating water, as well as about the insulation of the architectural structure itself, we want to tell you, as well as bring to your attention in this article.

Warm shower box

How to supply hot water

The main problem for a shower that is separate from the house is hot or at least warm water - if this can be organized in a building from a common system, then autonomy is needed here.
In this case, the most convenient option- this is a flowing electric heater, because almost any Vacation home connected to the mains, therefore, the installation of such a device is negligible technical problem where the instructions for safety against electric shock must be observed.
Let's say right away that this is not any super option - to very high temperature the device does not heat the water, especially if it is cold, but, given the very specifics of a country shower, warm water will be enough for you.
In most cases, even if the price of the device is high, it will not heat water above 40 ⁰C, but you are unlikely to need more.
Another option is the supply of hot water from the house - the pipes are laid underground and insulated, but during transportation there are too large heat losses, and if this does not bother you, then this option is better than the first one.

How to heat a shower

Infrared wall heaters

Of course, in the summer you will not have a question about how to heat the shower stall - it will already be warm or even hot there, but in spring or autumn, when you plant a garden or harvest, in your soul you will most likely feel too chilly.

But you can make such a box with heating, and here, infrared heaters are the best suited for heating, and there are good reasons for this.

Firstly, the IR panel will heat up a small room very quickly, since there is a special principle of giving off heat calories - the panel will not heat the air, but nearby objects, which will just become a source of heat.

Secondly, such devices can be installed in any place convenient for you - on the floor, on the ceiling and on the wall, and, thirdly, they can be easily turned off and removed.

This very “third”, perhaps, is the dominant factor in favor of IR systems - they will not be stolen, since you will have the opportunity to bring them into the house for the winter, or even take them to the city.

Note. Infrared heaters come in not only different power, but also different configurations.
That is, it can be a device in the form of a panel, but it can also be a film type - the latest models can be installed under wall and ceiling cladding.

How to keep warm in the country shower

Insulation of the box with foam

Two materials are best suited as thermal insulation here - mineral wool(glass or stone (basalt), but not slag) and polystyrene (in extreme cases, extruded polystyrene foam, but it is much more expensive).

The process of laying such insulation is actually no different from installation in other rooms - all the same frame and fasteners that are most suitable for the material used.

Summer shower - the choice of an ideal and practical design (100 photos)

If you are doing installation from the side of the street, then this question disappears, as it were, by itself, but inside it is extremely important, otherwise you risk getting fungus and mold there.

Foil - excellent waterproofing

So, it is best to cover the insulation with an ordinary thick cellophane film, and then cover this entire structure with foil or any thin foil insulation, as shown in the photo above.

Here you immediately, as it were, "kill two birds with one stone" - protect the insulation from moisture penetration and create an infrared reflector.

The fact is that the foil has an excellent property - it reflects infrared rays, therefore, the excess of heat calories in boxing will be minimal.

Note. It is very important that you insulate not only the walls, but also the ceiling, because according to the laws of physics, heated air rises and if there is poor thermal insulation, then the warm air will evaporate very quickly.
The same applies to the waterproofing of the ceiling - the steam, rising up, will be reflected by the foil insulation.

Plumbing nuances

Since we are insulating the shower box on the street, it is quite natural that we will not make a drain (lattice) floor there, since from below it will cold air and all heating will be useless.

In such cases, of course, it is best to fill the floor concrete screed with insulation, which is most often used as an expanded clay pillow laid on a layer of sand.

That is, the screed is poured here according to all the rules - the soil is planned, then a waterproofing film is laid with a twist on the walls, then a layer of sand 2-3 cm is poured and after that - an expanded clay cushion, the thickness of which depends on the coldness of the soil, but not less than 4-5 cm.

Do not think that we made a reservation about the waterproofing of the shower floor - the film is needed here not so that water does not get into the soil, but so that the pillow is dry - thereby reducing the thermal conductivity of materials.

You will need to mount a drain on the floor and take it to the public sewer, to a septic tank, or dig it nearby cesspool, only it should be used exclusively for soapy water.

But still, the best option would be a septic tank - you will not only not pollute the soil, but also will not breed unpleasant odors, which exudes stagnant water.

Conclusion

You understand that building a wooden box is easy enough, but how to make it so that you can wash in it during the cold season is a completely different question.

So such a seemingly insignificant building in this case will turn out to be a capital object, but if you bring water underground, you can wash there at any time of the year.

Shower cabins are a popular type of bathrooms. Their choice is very wide and it is easy to find the right model. Shower cabins with heated water are especially convenient and practical.

How to make a summer shower in your home with your own hands

The installation of such equipment gives maximum comfort when making water processes. The functionality of these types of bathrooms is quite high.

A good option for organizing would be a shower room for giving, which has a heating element. When choosing such a plumbing installation, it is worth knowing some of its features.

How to choose

The modern choice of sanitary installations for the bathroom is very large, there are cabins with different functionality, design and price categories. It's hard to choose among all the versions correct option, but if you focus on some parameters, you can quickly find the optimal model.

First of all, you should pay attention to:

Material and dimensions of pallets, walls, necks;
functionality;
Construction quality;
Frame sizes.

It is very convenient to use equipment with heating water for an apartment in which a heating element is installed.

They are simply irreplaceable in cases of frequent shutdowns of hot water supply in residential buildings or in the country. Such models are suitable for installation on wooden floors and alignment with the wardrobe.

Shower cabins and models for housing

The modern hot dessert cabin gives you a comfortable shower and a break from the city.

This design can have several options, such as a frame with a water tank and a heater. The capacity can be different, and the cabin can be supplemented with a miniature wardrobe, it has wooden pallet. Manufacturers produce such products for the convenience of consumers, so choosing the right shower is very simple.

Such equipment can be installed in the house next to the wardrobe, because the frame and walls have good tightness. In this way, the wood floor will not be damaged and will keep it appearance and properties. Water heating is carried out using a special element, and this requires electricity. Heated water shower equipment is completely safe and reliable when properly maintenance. The heated water shower cabin for the apartment is the standard model combined with an electric heating element.

To make a pallet, you can use various materials such as marble in expensive models or acrylic. Luxury designs finishes can be used in wooden decor and heating is very fast. That's why a large number of water can be heated much faster.

Different and sized shower enclosures for an apartment and therefore choosing the right model is easy.

The seat can be provided in the design, whether the mounting hole can only be present, and the seat itself asked.

The waterproofing of the shower cabin under the heating of the apartment is very good, the model is suitable for installation on a wooden floor, which has a hole for separation. The type of frame, its dimensions and the type of heating are selected individually.

Types of heating

Car shower VIMOIKA

Well, let's start with the most incredible - this, one might say, is a real know-how for human hygiene on vacation e.
We are talking about the VIMOIKA car shower, which you can use at almost any body of water, but, of course, if you have a car. This design works like a heat exchanger, but it needs to be built into the antifreeze line, with which the car interior is heated to the stove radiator, which in no way harms the functioning of the line and the antifreeze does not get into the water intended for the shower.

Scheme of connecting the unit to the heating main

To pump water, a 12V pump is used here, which is connected to a car battery, and the source can be a lake, pond, river, well, or just a canister of water that you brought with you from home in advance.
If there are difficulties with the dense approach of the car to the reservoir, then you don’t have to be especially upset - the hose will be enough for you for 30 m in length, while the lifting height can be up to 8 meters!

VIMOIKA in action

To connect VIMOIKA, first of all, as required by the instructions, you need to unwind the hoses towards the reservoir to make sure that you have arrived at a sufficiently close distance.
Next, connect the connectors from the shower and supply hose according to the marking to the heat exchanger, and also connect the connector from the supply and intake hose to the pump, and lower the intake filter into the water. After that, open the tap on the watering can and connect the cable to the battery - after filling the hoses, water will flow from the shower - you can use it.

Note. In the cold season (spring, autumn), you can simply increase the engine speed by adjusting the thrust on the gas pedal - the water will heat up more intensively.

Just be sure to drain all fluid from the hoses after use before storing them.

country shower

Plastic tank with heating and thermostat

For country house and cottages you can always use the so-called garden or country shower, where water is stored in a tank, only now it can be heated either from sunlight or from an electric heater installed inside the tank.

Such an energy storage device can be purchased at a store - they are produced with different volumes and different prices - but the price here depends not only on the size of the tank, but also on the material of manufacture - they can be either steel or plastic, as in the top photo.

Basically, the temperature of the liquid supplied here can be adjusted between 20⁰C and 80⁰C, and the volume can be from 90 to 200 liters.

Tubular electric heater - TEN

But you can save a lot on such units if you make a shower for a heated bath with your own hands - for this you will need a heating element and some kind of container - a plastic or metal barrel, a fuel tank or self-welded from steel sheets storage tank.

We will now tell you how you can do this at home using an electric drill with a crown cutter for inserting a heater and a simple electrician's tool (side cutters, pliers, etc.).

Pay attention to how the end of the tubular heater is arranged - this is shown in the upper image.

We will need to make a hole in the container along the diameter of the fitting (M), but so that it does not exceed the D value - this is the persistent part of the device that will fix the heating element with inside containers.

As a rule, the length of the fitting (L) should be sufficient for any barrel, fuel tank or whatever we have welded from metal sheets.

Holes in a metal container for heating elements

If you use a plastic container, then you will not have problems with holes - they are very easy to make with an electric drill with a hole cutter or a drill of the required diameter - it is much more difficult to do such work on metal tanks.

The fitting at the electric heater can be quite thick and you will not find a drill with the desired section, but there is a way out - you draw a circle of the desired diameter and pass along it with a 2-3 mm drill, after which you knock out or cut out the middle with a needle file.

Of course, such a hole will not be perfect (see photo above), but to give the edge a more or less clear outline, they should be processed with a semicircular file.

If the hole is uneven, you will avoid problems if you substitute metal washers with rubber or paronite seals on both sides (under the stubborn part of the heater from the inside and under the nut from the outside).

In addition, a summer shower in a bath with heated water will be much better if you connect a thermostat or even a thermostat with the heater, but the second option is only possible if you have a heater unit installed.

Flow heaters

Electric instantaneous water heater EVAN EPVN-7,5

Almost any such self-contained instantaneous heater can be used for showering.

even if the booth is located on the street. The most important thing here is the power supply, but electrical cable it is quite simple to bring it from home, you just need to follow the safety precautions.

Note.

Homemade summer garden shower in the country

Some users search the web for an electric heater such as a shower head for heating water, but such a device is installed only on taps. and you can connect a watering can there only by changing its design yourself.

Conclusion

Perhaps we have told you all the possible options with which you can get a hot water shower at home.

Of course, we did not mention boilers with various energy carriers, but this is already exclusively for indoor use.

More information

Hooray! To the cottage. Dacha is a great way to take a break from office routine or hard work in production. At the cottage, you can perfectly relax with friends, barbecue and cognac, or work on the site.

But in any case, after working in the garden or relaxing with best friends I need to clean myself up in the shower. Not every summer resident's estate is equipped in the same way as city apartment. But organizing a warm shower in the country is easy and simple.

What is needed for this? The answer to this question is different for everyone. Someone chooses a home-made design, someone will get a ready-made shower for a heated cottage, especially since the assortment is very wide.

If you decide to make amenities with your own hands, then first of all study your site. Evaluate his winning and losing zones. The shower room should be located near the house in order to wash and immediately be warm. You also need to take care of the drain. And of course, you need to choose exactly the area where the shower cabin fits well and harmoniously into the landscape.

In addition to choosing a place to build a shower, you should choose a water heater for a shower in the country. Water can be heated by the sun or by electricity.

To do this, choose a black water tank, or paint a metal barrel black. It heats up the water faster. A tank is installed on the shower cabin and a shower head is welded from below. You can make such a garden warm shower with your own hands. The big drawback is that it will only work on hot sunny days.

Shower for giving with heated water from the sun

In this case, the water for a country shower can be heated using sunlight. For this, a solar storage water heater was created. In these devices, water is heated, thanks to vacuum tubes. The water here is heated at any air temperature. In winter, such an apparatus heats water up to 60-70 degrees, and in summer period you can get boiling water. The device works perfectly even in cloudy weather, since the work depends on ultraviolet solar radiation.

Solar storage water heater for country shower

When installing an electric water heater, you need to make sure the quality of the wiring. If you do not have a central water supply in your country house, and the supply of water is limited or it has to be delivered, then you need a bulk heater. Typically, such heaters are equipped with a 50-100 l tank, a heating element, protection and a thermostat. Water is supplied by buckets or a pump.

Country shower with heated water from electrical network

Which method of heating to use depends on your capabilities. Today, many companies offer a heated country shower, like turnkey solution. Such complexes are equipped with a cabin, a tank, an electric heater.

And if you like to do everything yourself, then garden shower with heating will be an exciting adventure for you. To do this, you need to choose a place for a country shower, put metal carcass and hang wall-curtains from all sides, and install a heated tank on top.

There are metal and plastic tanks for heating water in a country shower. The advantage of plastic ones is that the water does not bloom in them, the welds do not rust, which means that the water in them remains clean, without impurities. The volume of tanks can be from 100 to 320 liters, both classic round and square.

superda4nik.ru

How to make a heated shower in the country?

No doubt, an outdoor shower is a necessary building for any country house.

But the climate of our country does not guarantee us an eternal hot summer. On cool days, the water does not heat up from the sun, and only a walrus is able to swim in the cold.

That is why it is necessary to equip a warm shower for a summer residence.

Of course, when there is hot water in the house, there are no problems. But it's so nice to wash in the comfort of an outdoor shower.

Sun heating

To provide warm water on the hottest days simple option is an ordinary barrel, which is painted black. A hose with a valve or a regular pipe with a water tap is mounted at the bottom of such a barrel.

Such an installation can be used even without building a shower house, and fix it on a regular summer cabin without a roof.

Heating Options

In showers for summer cottages with heated water, as a rule, electric tubular electric heaters (heaters) are used. But such heaters must be carefully monitored, when they heat the water to an acceptable temperature, they should be turned off. Usually heating lasts 3-4 hours.

The heating element can be mounted with your own hands, or you can buy a tank with a built-in one. If your experience with electricity is not enough, then it is better to purchase a tank with a ready-made heating element. In addition, the electrical wiring must be reliable in order to withstand the operation of the heating element for several hours.

Tanks with built-in heating are selected depending on the required volume of water. They are produced in volumes up to 200 liters from a variety of raw materials, the most popular of which is plastic or metal. Most of these tanks operate in the mode of the most common water boiler. The larger the volume of water, the slower it heats up.

Today you can buy tanks specially fitted to the shape of the roof of a standard shower stall. Usually these tanks are equipped with heating elements and special devices that are able to control the temperature and even turn off the heating element.

The highest temperature to which the heating element can heat is 85 degrees. The heated shower tank can be filled with a pump from a well or well.

Many tanks have a remote control for controlling water heating and operating mode. heating element. The temperature sensor (relay) is designed to control the temperature. An emergency thermal switch will, if necessary, turn off the heating element in the event of, for example, a lack of water.

The indicator shows the voltage level in the network. The bulbs serve as heat indicators. The electrical cord must be properly insulated and grounded.

Plastic tanks have one significant advantage over metal tanks - water does not bloom in them, joints and seams do not rust, as in metal ones, and therefore the water quality does not change. Naturally, the shower should be with clean water, as it is a means of hygiene.

It is strictly forbidden to turn on the heater in the network if there is no water in the tank. This can lead to overheating and, as a result, an explosion. Heating elements are not subject to repair, so in such a situation it will have to be changed.

Another option for a heated country shower is the use of titans. Titanium - is a monolithic metal tank, the lower area of which is intended for kindling coal or firewood, due to which water is heated in the upper part. In this case, another tank is needed, in which there will be cold water. In this case, the desired temperature is reached after mixing. Another advantage of titans is that when the water is heated, the shower room itself is also heated.

This heating model is very practical and easy to use, but you should not forget about fire safety rules. Titans need good ventilation and a chimney. Therefore, they are installed mainly in showers of capital construction.

A simple and cheap solution for suburban areas is also a shower bag. It is very easy to operate and does not require a separate shower stall. You can simply hang it anywhere comfortable spot. Cold water is poured into the bag, which is heated by the sun. You can also pour warm water into it, preheated on the stove. The volume of water in this shower is approximately 20 liters.

The portable shower can be equipped with a water heater and a pump that raises the water to a height of up to three meters. Such a device can be used not only for showering, but also for other household needs, such as, for example, washing dishes or a car.

During its use, there are no difficulties with installation, because it is simply not required. The device is connected to the water supply and plugged into the outlet. The power of such a device does not exceed 2 kW. 10-15 liters of water are heated with it in 12 minutes.

Heating water in a country shower is a necessary measure that provides comfort and gives pleasure while taking water procedures. And you no longer need to harden yourself and be forced to shiver under a cold stream of water in order to somehow wash yourself. A warm shower is a real find for an avid summer resident.

greensector.ru

Shower for giving with heating

We are so accustomed to civilization that the minimum comfort and communications must be present. Most of it is about water. Indeed, just think about why a few decades ago the dacha was a real summer "hard labor". And not because they had to physically work there, but because it was only possible to wash oneself after returning home.

Of course, the daredevils managed to solve this issue, but the materials were in short supply. Now everything has changed and turned 180 degrees. To make a shower in the country, just look at a couple of photo or video instructions, read various tips in more detail, go to the nearest construction market and stock up on everything you need. After spending a little more of your personal time, and a magnificent warm country shower will show off on the site.

Back to content

Method 1

The most natural simple and convenient. A cabin is being made or installed, a drain is being removed. A tank is installed at the top (it can be a regular plastic barrel). For better heating, it is painted black. The main thing is to install the barrel at the maximum height and in the “hottest” point, that is, in the place where the sun is the longest and most active.

In this case, at almost no cost, you can get good opportunity rinse after working with the ground.

On most modern dachas there is still a similar summer shower. No wonder, because its use is only a couple of months a year, therefore, saving money, such a design is often installed.

To begin with, you will need a radiator from an old car. Of course, it must be in working order. It can be purchased at disassembly and car markets. Next you need window frame, a radiator will be mounted to it. It is desirable that it has several glasses.

A special groove is cut out on the back of the frame, after which a radiator is inserted into it and fixed there.

The next step is to collect a special box. The main condition will be that the frame should serve as a cover to it. The box must be lined with foam from the inside. Sheets 3-5 cm thick are perfect for this. The radiator placed in the box should not touch its bottom, from here you can calculate correct depth. The box itself can be made of plastic or wood. He is not a keeper of water.

After placing the heating element with your own hands under the sun, you should run hoses from it to the barrel. The type of barrel, the design of the plumbing system is selected individually, based on the general parameters.

The tank will need to be insulated from the outside, so heat is accumulated. The result is an excellent natural water heater that retains warm water even after a cool night. To insulate the tank, you can use foam, mineral wool, foam rubber, in extreme cases, take ordinary hay or straw.

The heater and the barrel are installed at some distance from each other, the first is slightly higher, the second is vice versa. Hence the principle of operation, when heated water will go up, and cold water will go down. So it turns out that water from the bottom of the tank will flow to the radiator, heat up there and exit through the pipe.

Each of the methods, of course, can be improved if you deal closely with this issue. It turns out a do-it-yourself heated shower is a simple design, but it is advisable to approach it thoroughly, it will not be superfluous to look at photo examples or video tutorials.

design-vannoi.ru

Country shower with heating: options and features

Many city dwellers like to go to the country. But to make it more comfortable, you need to install a shower. There are several variants of this design. If you wish, you can install everything yourself. The types of country shower with heating are described in the article.

Compact options

This is the simplest heated country shower, suitable for summer. It is presented in the form of a small container of no more than 20 liters, made of reliable flexible plastic. Attached to it is a hose with a shower head. Water of the required temperature is poured into the container. If you fill it in the morning, then by lunchtime it will be warm. You just need to hang a container for a country shower with heating a little higher than your head so that water starts to flow. Take a shower where it is possible to cover the container.

A demanded model is considered to be a shower for giving, which does not need electricity to work. You only need a bucket with a volume of 10 liters or more. The device is presented in the form of a mat, which also functions as a foot pump. One hose is lowered into a container of water, and a watering can is located at the end of the other. If you stomp on the rug, then long-awaited water will flow from the watering can. You can swim both outside and at home. To keep the water warm, an electric heating element or a boiler is used.

More complex models have an electric pump so that physical strength is not required. Such models are placed in a container with water. Usually they can raise water to a height of 2 meters or more, which is necessary for a comfortable ablution.

IN multifunctional options There is also an electric heater. They work on the same principle - the device is placed in a tank of water, the cord is plugged into an outlet, and after 10-20 minutes you can swim. A water heater for a country shower is especially useful in cold weather in summer.

Even with the use simple devices it will be more comfortable to swim in a closed place. Therefore, a garden shower is needed. The shower cabin is presented in the form of a frame made of plastic pipes covered with opaque material. It can be a film, colored tarpaulin or plastic. On the ground, such structures are usually fixed on reinforcement pins driven into the ground.

If such a design is transferred weekly, then you should not worry about the drain - the site will not suffer. Any portable design can be used in it, and heating is performed by the sun. In bad weather, you can use an electric heater.

But with the installation of a septic tank or the creation of a cesspool, you can put a garden shower in a permanent place. In this situation, you can heat the water with a portable water heater.

Stationary devices

A country shower with heating of this type can be different. It differs:

Location: extension to the house or separate construction.
Heating method: electric heating element, solar energy, wood-burning stove.
Frame material and sheathing for a country shower.

Designs are summer and winter. In the latter case, you can not install it on the street. It is also placed at home, especially if it is possible to connect to the water supply system.

What does a country shower include?

A country shower with heating should be presented in the form robust design. Some of them can be used not only in summer, but also at other times of the year. The main components are:

Foundation.
Drain and shovel.
Cabin including frame, floor, pallet and trim.
Heated plastic shower tank.
Water heater.

Every element is essential. This will allow you to build a reliable and comfortable outdoor shower.

Base

Installation of a structure without a foundation is allowed only in the case of the above light portable design or the use of special modular cabins. They are fixed to the ground, and with the help of adjustable legs, the probable movements of the soil are compensated. But such designs are inexpensive, and it is quite possible to build stationary products with your own hands. Moreover, this will require less money to buy components.

Whatever the summer shower was built from, its weight is small. Therefore, it is required columnar foundation. The pillars can be foundation blocks, raised above the ground at a height of 20-30 cm, or pieces of asbestos-cement pipes 80-150 cm long. It is desirable to hammer them to a depth slightly exceeding the layer of annual soil freezing. You can make the pillars on your own, pre-filling the formwork with concrete.

drain hole

The easiest and most expensive way to install a safe and reliable drain is to use a septic tank with the replacement of its filler. But it is better to arrange a drain hole. For safety, it is desirable to install it at some distance from the shower.

The size of the drain pit can be 1-2 cubic meters. meters. In any situation, compared to a water tank, the volume of the drain pit should be 2 times its size. In order for there to be drainage, it must be covered with expanded clay or broken bricks.

Shelter

There may be a country shower with heating and a dressing room. The construction of the booth is the most creative part of the process. In this case, even the bravest can be introduced design ideas. The frame is metal, plastic or wood. Only all wooden parts are treated with a rot biocide and varnished before installation.

When choosing the height of the frame, you need to take into account that you will have to wash your hair in the shower. On average, the height can be 2.2-2.5 meters. The dimensions of the structure itself are set only by users. Usually it includes a cabin and a dressing room. And sometimes a water heater is installed. Minimum dimensions are 100 by 190 cm.

For sheathing is usually used:

Film, oilcloth.
impregnated materials.
Wood - lining, boards, slats, rods for weaving.
Polycarbonate - preferably opaque.
Polymer slate and plastic sheets.
Professional sheet.

A plank floor in the shower is ideal only for areas with sandy soil and with the use of a shower only in warm weather. Otherwise, it will blow from below. In other situations, a pallet is used. It is bought ready-made and connected through a siphon with a flexible hose to a pipe that will go to the drain pit. And you can do it yourself from concrete.

water tank

The volume of the heated barrel for a country shower is selected based on the number of people who will use the shower. About 50 liters of water is enough for a person. Tanks can be plastic and metal. The latter heat up better from the sun, but if there is a special heating, this point is not so important.

Plastic tanks have other advantages: they cannot react with water and cannot rust. They are light in weight. Often they are square in shape, which will help save on covering the top of the structure. After all, tanks are often placed on top, above the shower, so that the water inside is also heated from solar heat.

If it is difficult to choose a tank, you can purchase a model with a heating element. They are called so - water tanks with heated water - and are considered ordinary boilers. The temperature is set using a thermostat, and the thermostat turns off the heating when required. In addition to connecting the shower to electricity and plumbing, you need to use automatic control of filling the tank with water.

Water heaters

It is difficult to do without this element. There are several types of useful constructs:

Electric flow.
Bulk and storage electric.
Wood burning stoves or columns.

Electric instantaneous water heaters are usually used in the country, if there is access to a central water supply. It is mounted on various vertical surfaces. Designs provide hot showers even in inclement weather. The disadvantage of instantaneous water heaters is the high load on the power grid.

The accumulative device allows you to economically consume electricity, but heating is slower. Most models have a thermostat with which you can set the right temperature.

Bulk water heaters are suitable for summer cottages where there is no central water supply. Judging by the name, water is poured into it manually or by a pump. Usually the device is equipped with a heating element - a tubular electric heater. But thanks to the design of the thermos, you can keep the temperature for a long time.

If you do not want to install a device powered by electricity, that is great alternative heating water in the country with a wood-burning stove. This is a wood stove. This design is also called titanium. The wood-burning water heater is connected to the water supply, but can be used with a tank installed on the shower roof.

If this heating device is installed near the shower cabin, then with suitable insulation, it can be a heater. In this situation, with not very large area heating shower can be used even in winter. It is advisable to install a wood-burning water heater along with a shower in an extension to the house. In this situation, the area of \u200b\u200bthe heated territory increases, and after water procedures it will not be necessary to go out into the cold.

You can't do without heating in the shower. A wide variety will allow you to choose the right equipment. The presence of the necessary devices will make it possible to make a comfortable and convenient shower in the country.

Country life attracts with the opportunity to enjoy fresh air and unity with nature. Outside the city, everything is fine, except for the difficulties with taking hygiene procedures. Agree, it would be nice to make a summer heated shower with your own hands to solve this problem?

This option will help increase the comfort of staying in the country, but it will not greatly affect family budget. We will show you how to realize this idea.

The article details the best Constructive decisions and technology for the construction of booths. Effective help will be helpful tips on the choice of materials required in construction, the arrangement of drains, simple and fast heating of water. The information presented is supported by photo and video applications.

The comfort and ease of use of the design depends on how well the outdoor shower is designed. The task of a zealous owner is to build an economical, easily designed and at the same time the most functional shower equipped with heating.

The easiest option to perform is an open shower.

An outdoor outdoor shower is a frame-folding block or a modular container, one of the walls of which is adjacent to the main building

When choosing this arrangement option, the tank is installed on bearing wall buildings, positioning it in such a way that the sun's rays hit it at a right angle.

Do you prefer closed designs that are convenient to use both in warm time year, and in the cold months? Build a stationary outdoor shower with the simplest system heating. It may represent frame structure or major building.

The main advantage of this solution is that in warm weather the water in the tank is heated by sunlight, and in cold months with the help of a heating element.

Traditionally, when building a shower, in which there is enough space for an adult to bathe, they are guided by the following parameters:

height- 2-3 m;
width- 1.5 m;
length- 1.9-2 m.

The indicated dimensions are convenient for the construction of a structure made of wooden planks. Taking into account the thickness of the walls in the finished form, the structure in terms of area is approximately 2 * 1.5 m, of which an area of \u200b\u200b1 sq. m, and under the locker room - 60 * 40 cm.

When using boards standard sizes the material is consumed practically without residues.

In addition to wooden boards, the following are most often used as building materials for the construction of cabins:

polycarbonate sheets;
moisture resistant plywood;
sheet metal;
flat slate;
lining;
brick.

When choosing a facing material, it is important to focus on the exterior of the site so that the building harmoniously complements the already created architectural ensemble.

Polycarbonate shower cubicle:

Image Gallery

Purchase of necessary materials

In addition to the manufacture or purchase of a heating tank, it is necessary to purchase plastic water pipes D 50 mm. It is convenient to use a flexible silicone hose for water supply.

To equip a system of materials, you will also need:

gutter reinforced with metal mesh;
float valve;
divider.

To make a foundation pour when arranging a cesspool, you will need cement with markings from M150 and above. The drain can be covered with waterproofing roll materials or hydroglass.

For the manufacture of a wooden floor in the shower, it is best to use a tongue-and-groove board "forty", treated with a water-polymer emulsion or oil white.

For the final finish and arrangement of the bathroom, you will need paint for exterior and internal works, capacious shelves for bathroom accessories and hooks for clothes

For the construction of the structure you will need the following tools:

building level;
roulette;
corner;
screwdriver;
self-tapping screws.

For preliminary marking of the territory, it is also necessary to stock up on a skein of twine and wooden pegs.

Instructions for building a summer shower

There are no particular difficulties in building a summer shower on your own in the country. The only stumbling block for a novice master may be the question of how to mount a heated tank and how to organize a waste disposal system.

Step 1: Carrying out preparatory work

The amount of work involved in site preparation depends on the type of structure being built. If you plan to erect a temporary frame structure, to prepare the base, it is enough to remove a 15-centimeter layer of earth from the marked area, and then level the bottom of the dug "pit" and fill it with sifted sand.

When installing a shower stall on heavily heaving soils, in order to reduce the risk of it tipping over, the thickness of the non-heaving "pillow" of gravel and sand should be increased to 30-40 cm.

When constructing a wooden pouring floor over gravel, be prepared for the fact that while swimming you will experience some discomfort due to a slight draft

Are you planning to build a capital country shower with heating? For its construction will require laying the foundation. The depth of the foundation depends on the type of materials used. For example, for a brick building, a foundation deepened by 30-40 cm is quite enough.

The laying of the foundation is carried out in the following sequence:

Territory marking. To create the right foundation, wooden stakes are hammered in at the outer corners of the future building and string is pulled between them.
Digging a "pit". A layer of soil is removed from the marked area, deepening, depending on the type of building, by 15-40 cm.
Site preparation for laying pipes. Dig trenches and level the bottom in such a way as to ensure unhindered flow of waste water in the direction of the drain pit.
Installation of drain and discharge pipes. A reinforced chute is installed on a leveled and compacted bottom, not forgetting to maintain the angle of inclination.
Pouring with concrete mortar. To create an even base, pouring is carried out using a level and guides.

For interior decoration choose facing materials with increased moisture resistance: pvc film, linoleum, plastic. When choosing wood paneling the surface must be treated with drying oil and painted.

To make the adoption of hygiene procedures more convenient and safe, a grate knocked together from wooden boards is installed on the floor, on top of which a rubber mat is laid.

The grate is assembled from wooden slats 30-50 mm in size. Wood preparation is the same. If you want to increase its resistance to shoe wear, treat the material with an acrylic compound used for repairing bathtubs.

It is advisable to separate the changing room and the bathing area with a curtain made of waterproof textile fabric or PVC film.

If desired, both the inner and outer walls of the facing material can be painted and decorated with drawings. original design will turn the shower not only into a place for taking water procedures, but also into decorative element suburban area.

Additional interesting options garden shower arrangements are suggested in these articles:

The summer heated shower is ready. To prevent stagnant water, it is advisable to operate the shower at regular intervals. Before a long break in use, so that the sediment does not clog the watering can, it is recommended to empty the tank completely.

Of course, before you start building, you will have to make drawings of a warm shower in the country with your own hands in order to calculate all the materials, and in addition, the technical capabilities that you are going to endow this building with.

Indeed, often heated water occurs in such buildings only in hot weather, that is, it is heated naturally, depending on weather conditions, but it can also be forced heating.

It is about this forced method of heating water, as well as about the insulation of the architectural structure itself, that we want to tell you, as well as bring to your attention the video in this article.

Warm shower box

How to supply hot water

The main problem for a shower that is separate from the house is hot or at least warm water - if this can be organized in a building from a common system, then autonomy is needed here. In this case, the most convenient option is a flow-through electric heater, because almost any country house is connected to the mains, therefore, the installation of such a device is a minor technical problem, where the safety instructions from electric shock must be observed.
Let's say right away that this is not some kind of super option - the device does not heat water to a very high temperature, especially if it is cold, but, given the very specifics of a country shower, warm water will be enough for you. In most cases, even if the price of the device is high, it will not heat water above 40 ⁰C, but you are unlikely to need more.
Another option is a hot water supply from the house.- pipes are laid underground and insulated, but during transportation there are too large heat losses, and if this does not bother you, then this option is better than the first one.

How to heat a shower

Of course, in the summer you will not have a question about how to heat the shower stall - it will already be warm or even hot there, but in the spring or autumn, when you plant a garden or harvest, in your soul it will most likely seem too chilly. But you can make such a box with heating and here, they are the best fit and there are good reasons for this.

Secondly, such devices can be installed in any place convenient for you - on the floor, on the ceiling and on the wall, and, thirdly, they can be easily turned off and removed. This very “third”, perhaps, is the dominant factor in favor of IR systems - they will not be stolen, since you will have the opportunity to bring them into the house for the winter, or even take them to the city.

Note. Infrared heaters come in not only different power, but also different configurations.
That is, it can be a device in the form of a panel, but it can also be a film type - the latest models can be installed under wall and ceiling cladding.

How to keep warm in the country shower

So, we need an insulated shower in the country, that is, given that our construction will be quite simple, most likely from boards or OSB, this will not be enough to keep the cold from the street inside. Two materials are best suited here as thermal insulation - mineral wool (glass or stone (basalt), but not slag) and polystyrene foam (in extreme cases, extruded polystyrene foam, but it is much more expensive).

The process of laying such insulation is actually no different from installation in other rooms - all the same frame and fasteners that are most suitable for the material used.

But there is one very important nuance here, which arises in connection with the specifics of the shower box - it is constantly humid there, therefore, thermal insulation must be protected from water splashes. If you are doing installation from the side of the street, then this question disappears, as it were, by itself, but inside it is extremely important, otherwise you risk getting fungus and mold there.

Foil - excellent waterproofing

So, it is best to cover the insulation with an ordinary thick cellophane film, and then cover this entire structure with foil or any thin foil insulation, as shown in the photo above. Here you immediately, as it were, "kill two birds with one stone" - protect the insulation from moisture penetration and create an infrared reflector.

The fact is that the foil has an excellent property - it reflects infrared rays, therefore, the overexpenditure of heat calories in boxing will be minimal.

Note. It is very important that you insulate not only the walls, but also the ceiling, because according to the laws of physics, heated air rises and if there is poor thermal insulation, then the warm air will evaporate very quickly.
The same applies to the waterproofing of the ceiling - the steam, rising up, will be reflected by the foil insulation.

Plumbing nuances

Since we are insulating the shower box on the street, it is quite natural that we will not make a drain (lattice) floor there, since cold air will flow from below and all heating will be useless. In such cases, of course, it is best to fill the floor with a concrete screed with insulation, which is most often used as an expanded clay pillow laid on a layer of sand.

Do not think that we made a reservation about - the film is needed here not so that water does not get into the soil, but so that the pillow is dry - thereby reducing the thermal conductivity of materials.

You will need to mount a drain on the floor and take it to the general sewer, to a septic tank, or dig a cesspool nearby, only use it exclusively for soapy water. But still, the best option would be a septic tank - you will not only not pollute the soil, but also will not dilute the unpleasant odors that stagnant water exudes.

Conclusion

You understand that building a wooden box is easy enough, but how to make it so that you can wash in it during the cold season is a completely different question. So such a seemingly insignificant building in this case will turn out to be a capital object, but if you bring water underground, you can wash there at any time of the year.

Most summer residents think about creating a shower in the country with their own hands.

First, it is an opportunity to improve comfortable conditions without big expenses.

Secondly, a properly equipped outdoor garden shower allows you to meet the necessary sanitary needs, as it is suitable for use at any time of the year.

And besides, crafts for its decoration are made exclusive any garden plot.

Design features

If the shower will be used exclusively in the summer, then a simple quick-mounted structure, such as a shower rack, a camp shower or a toptun, is sufficient.

You can install a simple camping summer shower with your own hands in a fairly short time.

If long-term operation is planned, including in the cold season, then it is necessary that the design of the shower-craft is reliable and provides for the possibility of installing equipment for heating not only water, but also air in the cabin.

It is more difficult to install a winter shower in the country with your own hands, since its design needs a frame and a foundation.

Regardless of the modification, the country version of the design provides for the following equipment:

base or foundation;
drain ladder or drain;
pallet and floor;
cabin;
holder-diffuser and stop valves;
pipeline;
devices for pumping and heating water, as well as for heating the cab.

As a material for such crafts as a country shower room without a foundation, film or plastic is used.

For booths installed on the foundation, it is preferable to choose more durable materials - wood or brick. A good option- do-it-yourself polycarbonate shower.

The most famous modifications of the shower craft used in summer cottages:

Toptun - mat with pump and hose. The water supply is provided by pressing the feet on the mat;
Camping - a compact portable plastic container equipped with a hose and nozzle. It can be stationary, mobile;
Circular. The circular option provides water supply from all sides;
Alekseev. Provides hydromassage by supplying water under high pressure;
Tropical. The flow of water entering through a special grate looks like a tropical downpour.

Making a circular shower with your own hands is quite difficult, but the result of this work will please any summer resident.

Toptun - the most popular shower among summer residents

Simple craft designs for shower devices intended for summer use are considered optimal solution issue of dacha hygiene.

After all, installing the same circular or tropical shower is not as easy as it might seem at first glance. That is why, choosing which shower to make in the country with their own hands, summer residents most often stop at a trample.

To build a toptun shower with your own hands, you will need a car pump, two corrugated hoses, a container with a lid, and a shower head. You don't even need a holder.

The sequence of operation of the toptun:

Water of the required temperature is drawn into the container. Considering that the volume of the container is small, a do-it-yourself shower tray, if it is a toptun, is not needed;
Crafts are attached to the lid - a wooden or rubber cork equipped with holes and tubes, the diameter of which corresponds to the diameter of the hoses;
The container is covered with a lid with attached hoses - one from car pump, the second - the holder of a shower head. Under the pressure of air from the pump, water enters the hose. The watering can is held in the hand or attached to any surface.

By the same principle, you can make a camping summer shower. To do this, you will need a rubber mat or pedals equipped with built-in valves, as well as two hoses.

As a container for water, an ordinary bucket is used, covered with a lid, in the hole of which the inlet hose-holder of the watering can is fixed.

As in the first option, the pallet is not required, and the earth replaces the drain drain.

Water supply to hiking option carried out by alternately pressing the pedals with your feet.

Each step provides one serving of water. As a rule, the marching method saves water and is used in conditions with limited access to water resources.

Also, a camping outdoor shower can be used to wash a car.

A circular shower can be considered as another option for a country house, but in this case, the actions listed above will not be enough. You will need a special holder for it.

How to expand functionality?

The functional purpose of a shower room, even in summer cottages, should not be limited solely to hygienic considerations.

For many summer residents - this is an important part of the suburban area.

But not everyone knows that a do-it-yourself country tropical shower in a bath can fully replace many of the procedures offered by spa salons.

In practice, the available functionality of the shower room is the result of the choice of its type.

That is, in order for the built country shower in the bath to live up to expectations, you need to learn more about its functionality and installation steps.

In the minds of most people, a bathhouse is associated with a healthy lifestyle, and visiting it is considered a preventive measure.

Therefore, the famous shower of Alekseev will come in handy in the bath.

Alekseev's shower is a new generation design, an analogue of the well-known Charcot's shower with hydromassage properties.

But Alekseev's shower, an invention of the Russian doctor of the same name, is equipped differently and has no analogues in the world in terms of the effectiveness of the impact.

The use of a device created according to the Alekseev method provides healing through massage and is recommended for many diseases.

To independently install Alekseev's shower in the bath, you need to understand how it works.

The unique difference of the device is the high-speed streams formed using the special design of the holes in the nozzle for the watering can.

If you make such a nozzle yourself, then installing Alekseev's device in your own bath is not difficult.

To do this, it is necessary to drill cone-shaped holes in the nozzle for the watering can - wide on the side of the water flow and tapering towards the outlet.

Then the craft nozzles are installed on the holder. The holder must be chosen carefully.

Considering that Alekseev's device gives a strong flow of water, care must be taken that the ladder ensures its full drain, or use a pallet.

At the same time, Alekseev's shower can be operated not only in a summer cottage, but also in an apartment.

Features of self-installation of various types

The functions of the device used in summer cottages can be expanded if you use the non-standard capabilities of its structural varieties.

For example, a circular shower, along with hygiene, will also provide a healing effect.

According to the principle of the device, the circular type of shower is a few systemically located pipes equipped with small holes and a faucet.

In the center is a holder with the main watering can. With the help of a tap, the water supply pressure is regulated.

Thus, the circular shower additionally provides a comprehensive hydromassage of the body.

You can install such a device yourself both in the country and in the apartment.

To create an original shower craft, it is necessary to connect several pipes equipped with small holes in series with the central riser, on which the mixer holder is located.

In shape, the circular type of shower resembles the back of a chair with transverse or longitudinal crossbars.

Then you should take care of the flow of water - the ladder will cope with this task. The owner of the cottage has the right to decide whether he needs a pallet in this case, or a ladder will do just fine.

An excellent alternative to a regular shower can be a rain shower. This is a device whose water flows mimic a tropical downpour.

Functionally, the tropical shower type is a hydromassage device.

However, not every apartment has the opportunity to install a rain shower, but if such a design is installed in the garden, the impression of authenticity will be complete.

It is not difficult to build a rain shower in the country on your own. To do this, it is enough to increase the area of \u200b\u200bthe watering can of the mixer and strengthen its holder.

A ladder will help control the discharge of a powerful stream of water, which distinguishes a rain shower. It is also convenient to use a deep pan.

But you need to remember that both the holder, and the ladder, and the watering can must be of high quality.

Construction stages

To build a summer shower with your own hands, you need to know the basic rules of the process:

Preparation - determine the dimensions and draw a diagram;
Choice of location - a sunny place on a hill, which is not too far from the house and the water supply, but with the possibility of arranging a drainage system if a ladder is provided in the shower equipment, or a drain pit if a pallet is installed;
Construction of the foundation - level the site equal to the size of the building, then fill it with concrete;
Installation of the frame - piles are installed and fixed at the corners of the site, then they are tied up, constructing the shower floor. The racks of the frame are fixed with self-tapping screws. Build walls and roof;
Summing up communications - installation of a tank, equipment for draining, lighting and ventilation;
Mount pipes and a pallet - it is necessary to drain water. Sometimes they do not use a pallet, but the floor in which the ladder is mounted big size. The best option drain systems - a ladder with a lock and a grate. The shower drain performs the function of a sewer, but may have a different throughput;
Waterproofing, wall cladding. For operation in the cold season, the walls need to be insulated;
Decorative shower cubicle. beautiful crafts increase the aesthetic appeal of the entire suburban area.

If the weight of the structure is small, then a foundation is not required for its installation. For example, a metal frame for a polycarbonate booth is installed on fittings driven into the ground.

In addition, it is physically easier to build a do-it-yourself polycarbonate shower than a brick one.

A properly built base will allow you to upgrade your shower room in the future and enjoy its new possibilities endlessly.