Portable do-it-yourself shower. Do-it-yourself welded summer shower for a summer residence

You can easily make and equip a summer shower in the country with your own hands. Photos and dimensions, as well as recommendations for choosing a place for construction, you will find in this article. After all, there is nothing better summer heat than to freshen up with cool water, especially after active work on personal plot. With the onset of hot days, the presence of a shower in the country becomes an urgent and necessary requirement. This factor is especially important if your house is under renovation, and plumbing communications have not yet been completed.

In any case, the interior space of the shower must be spacious so that the bathing person can comfortably accommodate himself and with him all the things necessary for this procedure. The most common parameters of country shower buildings are 2.5 meters high and 190/140-160/100 cm wide. It is necessary to plan the construction of a summer shower in the spring, at its very beginning, so that by the time summer comes it will be ready.

There are no particularly strict criteria regarding the arrangement of such a shower. With imagination and the ability to keep construction tools in your hands, you will be able to translate your ideas into reality and build such a necessary thing for giving. Depending on the complexity of the plan, it is possible to equip a simple outdoor shower in one day. A more detailed project will take more time, but it will also serve you for more than one year.

Shower for a summer residence, which place to choose for it

So that the water in the tank is not cold, it is more logical to place the shower building in a place illuminated by the sun's rays. If you prefer to take a shower in the afternoon or late afternoon, then you should choose a part of the site where the concentration of solar activity is observed in the afternoon. It is important that this place is protected from winds.

Second an important factor is the presence of a drain for used water. A summer shower for a summer residence should be installed on a hill so that the water drains quickly and does not stagnate, attracting insects. The exploitation of any soul implies the use large quantities water, and if a lot of people will wash in it (a large family), then this nuance needs to be calculated and properly equipped.

If the capacity of your shower tank will be approximately 1-2 m³, then drain hole will definitely be needed. When arranging a place for water flow, it is important to correct placement- in no case should it be located under the building itself. A sewer pit or a septic tank with drainage should be located at some distance from the booth, in turn, the slope should go in their direction.

The presence of a waterproof layer for runoff is highly desirable: hydrostekloizol, PVC film, roofing material or concrete screed suitable for this purpose. drainage pit should be located at a distance of at least 3 meters from the cabin, its depth should be 2.5-3 meters, the bottom is covered with gravel or a thick layer of sand. The top of the pit must be covered and fenced off.

How to make a shower in the country - an example of a simple design

options for this useful dacha building there can be a great variety - here the matter already depends on your creative approach. For example, we will consider the features of the "standard" version of the country summer shower.

The shower should be comfortable, so the most minimum dimensions the internal space should be at least 100 × 100 cm. Movement should not be constrained - a person should freely raise his hands and bend over in the process of washing. It should also be highlighted small place for clothes and towels (cloakroom), 50-60 cm is enough for him. Thus, in the total footage, the size of the shower will be 160 × 100 cm and 2-3 m in height.

Install strong and reliable racks - this is your safety, since the tank filled with water for an outdoor shower has a huge weight. Ideal for this purpose wooden beam 100×100.
It is better to dig the racks into the ground, having previously treated them with tar or a fat-containing agent. Pour them concrete mortar, by the way, will be the best.
For the container at the top, a horizontal platform should be equipped.
The cabin is made of any materials, the main thing is that it should hide the swimmer from prying eyes and protect from drafts.
Containers for a summer shower can be metal or plastic. It is worth considering that the metal tank will heat up faster, but it will also rust. In order for the water to heat up quickly, it is recommended to paint the tank with black paint.
If you make a frame over the tank and cover it with a plastic film, then the process of heating water will be much faster.
The valve for the tank can be anything, but a ball valve is most suitable.

The whole process begins with marking the perimeter of the future shower, the racks are installed at the corners and connected from above with a dressing from a similar beam. After that, there is a turn of the lower dressing, keep in mind that it should be located 10-15 cm from ground level.

To fasten all frame fragments, use long bolts - this will have a positive effect on the overall strength of the structure.

However, you can do it easier and install a metal or acrylic tray, while the water will be drained using a hose.

To ensure that the shower door closes tightly, use seals. The shower compartment and the dressing room can be separated by a special curtain, and it would be better if the threshold between these two compartments is somewhat high (to prevent water from flowing into a dry room).

The summer shower, as already mentioned, can be finished with absolutely any material on the outside. Lining, plastic, polycarbonate, moisture-resistant plywood, fiberboard, slate, metal sheets, siding - the main thing is that the building is in harmony with the rest of the buildings on the site.

It does not hurt to pre-open wooden materials with protective compounds.

If the frame is welded from metal, then it must also be coated with anti-corrosion agents or painted with paint.

In order for the water in the tank to heat up many times faster, rafters can be laid on top of the upper trim, and a sheet of roofing iron can be placed on top of them. The metal will reflect the rays of the sun, which will make the process of heating water more active.

Summer shower tank, which one to choose

Separately, it is worth paying attention to water tanks or shower tanks - their choice is determined by the individual requirements and preferences of the developer. They are small and large-capacity, flat and round, iron and plastic. The size of the tank depends on how many people will wash in this shower, often a volume of 100-200 liters is enough for an average family. As mentioned above, it is better to choose a tank of dark color or even black - so the water will heat up faster.

Such a container must have a lid so that various debris and insects do not get inside. At the very bottom of the tank, a tap outlet is mounted, to which a diffuser is screwed.

There is important point- the tap should be located on the lowest part of the tank, so that all the water drains from the tank and does not stagnate.

Equipping a summer shower with your own hands, you can purchase a ready-made tank in a specialized department of the building market. On sale there are also containers specifically for such showers, with all the necessary parts included.

If you have a metal or plastic barrel of a suitable size, then after certain manipulations it can turn out to be a perfectly acceptable shower tank. For these purposes, a hatch is cut out on top of the barrel laid on its side to fill the water, and it is processed acrylic enamel(or bath repair agent) from the inside - this applies to metal containers.

And you can not lay the barrel on its side. Everything is within your power if "hands grow from where it is necessary."

Also in this role, tanks from those that have become unusable “act well” washing machines. Despite the fact that their volume is enough for 2 washes, they very quickly adapt to the shower tank, thanks to the presence of inlet and outlet pipes, as well as the necessary technical holes. Such tanks are not afraid of corrosion.

Equipping a summer shower in the country with your own hands, it is better to prepare photos and dimensions, as well as approximate drawings, in advance. So you will see all the working stages clearly and will be able to accurately calculate the final result. With such a work plan in front of your eyes, you will know how much material you will need for external and interior decoration booths and drain pits.

Paying attention to the functional part, do not forget about the aesthetic appearance of your summer shower - everything should be not only comfortable, but also pleasing to the eye.

It is not difficult to make a shower cabin with your own hands for a summer residence. It can be made both budgetary from improvised means, and expensive and complex. We will focus on the first option in detail. Indeed, in the summer, for many owners of a summer cottage, functionality is much more important than appearance.

Where to begin?

First of all, you need to understand what you want to get in the end. What qualities, amenities and functionality should a shower cabin have for a summer residence? How many people will use the shower? The choice of tank capacity and the need to drain water depend on this.

An important factor is the peculiarity of the landscape and soil of the site. If there is an elevation, it is better to make a shower cabin there. This will save you the trouble of draining the water. It is desirable that the sun falls on this place all day. If you have an automatic water supply, you can make the automatic filling of the tank.

Elevated shower installation

Also worth deciding. what material will you make a shower stall for giving. The frame is made of metal round or shaped pipes. You can stop the choice on wooden bars. The material for the walls is very diverse. It all depends on your imagination and budget. For these purposes, suitable: tarpaulin or any dense fabric, polyethylene film, slate, wood, lining, metal profile sheets, bricks and more.

A do-it-yourself summer shower cabin for a summer residence can be attached to a country house, made a separate building or mobile. The latter option does not require a foundation, and if necessary, the structure can be disassembled and freed up space. In this case, the shower is sheathed with light material.

Think in advance how the water tank will be arranged. Whether you want to make it heated or you are satisfied with one in which the water is heated by sunlight. The drainage of water is also important. The drainage system should be considered before construction begins.

Plan the dimensions of the shower stall for a summer residence as spacious. After all, you will need to put bath accessories and put your things. In height, it must be at least 2 m, and the base - at least 1x1 m.

Choose pipes of at least 20x30 mm, a corner of 45x45 mm. Of the tools you will need:

welding machine;
Sander.

Create a drawing of a future shower cabin for a summer residence. Be sure to include jumpers at the bottom and in the middle. To make it easier to fix the floor boards, use a corner as the bottom jumpers. Make the upper stops also from the corner, because. it is easier to fix the water tank on it. Their dimensions will depend on the capacity of the tank and its material. If the tank is metal, the stops must be such as to support its weight with water.

Depending on what material for wall cladding you choose, you need to consider the location of the fasteners. For plastic or metal profiles, it is worth welding metal plates. If this soft materials, such as tarpaulin or rubberized cloth, they can be fixed with a strong synthetic thread directly to the pipes.

Upon completion of the design work, we proceed directly to the assembly. You will need:

4 pipes 2-2.2 m long for vertical supports;
8 pipes for central and upper lintels;
4 corners for the bottom;
corners for stops under the tank.

If you plan to make opening doors, 4 more pipes and 2 hinges. All parts are cut at an angle of 90°. Clean all edges for welding. How to make the design more rigid? To strengthen it, you can weld metal corners at the corners of the frame or attach them with bolts to vertical posts.

During welding, never weld the seam completely on one side at once. First, “grab” a little from all sides and only then thoroughly weld the joints. Otherwise, the metal will pull in the direction of welding and it will be impossible to return it back.

It is better to take electrodes with a diameter of 3-4 mm. They are convenient for welding both thin metal with a thickness of 1 mm, and thicker metal - 4 mm. Select such a current strength that the metal melts. If you set a large one, you will burn through the walls of the pipes. At a lower value, the electrode will stick to the metal. If you have never brewed or are not sure if you can do everything right, contact a professional. After all, a poorly welded structure can fall under the weight of the tank and cause injury.

Spend welding work on a flat surface. It is important to keep the 90° angle everywhere. Check this with a square. At the end of the work, clean all the seams with a grinder with a grinding disc, remove sharp corners and burrs.

For painting, choose a special paint for metal. To protect the frame from rust, go through the primer before painting, and then apply 2 coats of paint or enamel. If you are using profile pipes, use a roller. This will save time and reduce material consumption. After the enamel dries, we proceed to the manufacture of the wooden floor and the installation of the shower tank.

Cabins with wooden frame

The general design may be the same as for the cabin with metal frame. Bars 50x50 mm in size and boards 50x100 mm are used as racks and jumpers. Before installation, the tree is planed to level and clean from roughness.

According to a pre-created drawing, boards of the required dimensions are sawn off. The assembly of the structure is started on a flat area. It is better to make connections half a tree, however, you can use metal plates for fasteners. Attach the bars to them with the help of self-tapping screws. If you have doors in your project, put them on hinges. But you can use a regular curtain.

Provide a place to install a water tank. If it is small, only half of the roof can be covered with boards. If the tank is large, it is worth installing a grate on the entire surface. The same lattice is made on the floor. Attach bathroom shelf and hooks.

Since the tree will be exposed to water, it must be treated with an antiseptic, drying oil or oil. It is advisable to make several layers, each subsequent one should be applied after the previous one has dried.

Some owners make a concrete foundation for country shower cabins. Since an outdoor shower is still a temporary structure, you should consider whether it is necessary to fill in such a foundation for it. This process is laborious, and if you decide to move or even want to remove the booth from the site, you will have to break the foundation.

As a basis, you can use paving slabs. But to avoid distortions, prepare this small plot. Remove some earth, level it, lay geotextile, crushed stone and level the surface with sand. Tiles are laid on top.

Drainage and shower tank

Someone arranges entire drainage and drainage systems under the shower cabins. Someone does nothing. How to understand what you need? To do this, you need to take into account some factors. First of all, you need to understand that, most likely, the volume of the tank will not exceed 60-80 liters. And if only 2 people use the shower, then the volume will be much less. In the sun during the hottest time of the day, such a container will warm up for at least 2-3 hours. And during this time, the water will go into the ground.

However, if you have clay soil and the water does not drain well, or are you afraid that there will be unpleasant odors, then you can organize a water drain system or a drainage pit.

Consider how to make a drain into the drain. To do this, a hole breaks out under the shower or at a short distance from the cabin. The choice depends on free space Location on. Approximate dimensions are 50 cm deep and 1x1 m long and wide. It is filled with coarse gravel. To save space, the lower half can be filled with construction waste, and the upper half with gravel. Everyone is tamped down and a shower stall is placed on top. Since the outdoor shower is placed in the sun, the soil will dry out faster.

If you are afraid that the walls of the pit may crumble, you can install car tires, and then cover everything with gravel or building debris. Drainage made according to this sample will last a very long time.

A plastic or metal container can be used as a water tank. The first one is lightweight and cheap. Of the shortcomings, it is worth noting that most containers of blue or white color. It's hard to find black. And so that the water heats up faster, it is better to use a black color. In addition, the water outlet is often not firmly fixed. Subsequently, this leads to the fact that it begins to hang out and a leak forms at the junction.

Metal containers are much stronger than plastic. In addition, they are easily dyed in any color. The disadvantages include a lot of weight. Any metal container is suitable as a tank, for example, a tank from a washing machine. It is easy to connect a branch pipe with a tap to it.

Filling the tank and operating the shower

The issue of filling the container with water is important. After all, doing it with buckets is far from the most convenient option. It is advisable to organize the water supply through a hose. To make automatic water supply, use the float from drain tank toilet. Set it to a response difference of approximately 20 liters, considering the capacity of the tank. Thanks to this, you will always be able to maintain the required volume of water, and it will not overflow.

Not in all regions in summer the sun heats up so much that the water heats up quickly. The solution to this problem can be electrical heating. So you can have warm water regardless of the weather.

If the shower is attached directly to the container, you need to take care of its secure fixation. After all, with prolonged use, the pipe will loosen. To avoid this, use a valve-type faucet. In addition to the fact that it has an easier stroke of the rod, it is also more convenient for them to regulate the water pressure. At the same time, its surface does not oxidize.

At the end of the operation of the shower cabin, when the cold sets in, it must be prepared for the winter. All containers should be removed indoors. If this is not possible, drain the water from them. All connecting elements are unscrewed and removed. The same with hoses.

Industrial booths

There is now a wide range on the market finished products. It differs in price, materials of manufacture, you can choose any design, functionality and volume of the tank. Users of such designs respond very well to this product. However, there are some drawbacks. If these are plastic booths, the fragility of the material can be attributed to such disadvantages. Another is that the shower is mostly formulaic.

When you make it in the country with your own hands, you can take into account all your wishes and translate them into a project. Change the height, expand if necessary, increase the diameter of the drain hole, add decorative elements. This is difficult, and sometimes impossible, to do in industrial showers.

And, perhaps, the main disadvantage is the high cost compared to a do-it-yourself shower. After all, a simple booth can be made from improvised materials. And it may happen that you spend only your time on manufacturing.

We have analyzed in detail how to build a shower stall with our own hands. It is not difficult to do this. It is only necessary to think carefully about everything, take into account the wishes and features of the site.

Video instruction

A wooden summer shower for a summer residence is small building on the site, but the significance and benefits of which are undeniable. It is difficult to do without a shower in the warm season. In addition, a country shower can be attributed to a way to save the family budget, since the water in the tank or barrel is heated by the sun.

Any material is suitable for building an outdoor shower, but wood will be the most organic and inexpensive.

Of course, you can buy a ready-made wooden shower, but if the budget is limited, then it would be right to make it from improvised materials. Edged boards and timber, as a rule, are available on the site in the form of residues after the construction of a house or outbuildings, if not in full, then partially. Consider step by step all the stages of building a simple outdoor shower design.

How to make a wooden shower with your own hands

First you need to choose the right place, so that it is illuminated by the sun for as long as possible, and provide an elevation. If the terrain does not allow you to install a shower at a height, you need to make a small embankment to organize the flow of water.

The second point is to prepare the material. To build an outdoor shower, you can use the most affordable and relatively cheap material on the farm - wood (boards, timber), preferably coniferous.

The advantages of wood as a material for making a shower:

ecological clean;
accessible;
aesthetic;
easy to process.

A significant minus of wood is susceptibility to moisture and bugs (eliminated by additional processing and periodic maintenance).

Schemes and drawings of a wooden shower for a summer residence

A summer shower made of wood is so simple that drawings for its manufacture are practically not needed. But, in order to understand the construction, we give a few examples:

As can be seen from the figures, the construction wooden shower is not particularly complex. But before you start, you need to consider the following:

lighting. They use a summer shower not only during the day, but also in the evening. Therefore, it is necessary to provide lighting - natural or electric. These can be windows in the wall, open openings or electric lamps. Most often, a country wooden shower is simply left without a roof;

ventilation. Fully indoor shower from wood needs ventilation. To do this, it is necessary to provide ventilation hatches;

heating. To be able to shower in early spring or late autumn, when the intensity of the sun and the length of daylight is not enough to naturally heat the water, many provide additional water heating. Among the popular heating methods are: installing a stove or column, installing a boiler (electric water heater), adding a shower room to the house and connecting to a central water supply, using a boiler.

Tip: using a water heater it is better to divide the water tank into two halves or use two tanks and a mixer.
When equipping a heated wooden shower, take care of safety, use the wire of the required section, isolate it from moisture, etc.

locker room. To keep clothes dry, you can leave them outside the shower, or you can make a wooden shower for a summer house with a dressing room. Moreover, users are advised not to make two separate rooms, but simply to separate the shower with a curtain. This will allow you not to waste time, area and material on construction and leave more space for swimming;

bath accessories. For storage, it is enough to make simple wooden shelves. But their location needs to be considered. They should be close to reach out with your hand, and not interfere with taking water procedures.

Construction of a country wooden shower

The manufacture of a summer shower made of wood is carried out in several stages:

Shower drain device

A wooden shower is afraid of moisture, so you need to take care of the quick drainage of water from the shower in the country. This is especially true for indoor spaces.

The simplest shower drain is to drain water directly into the soil under your feet. But soon a small swamp will be formed near such a shower, attracting insects and creating bad smell, and unkempt appearance.

A properly organized shower or drain system consists of a floor, a drain and a septic tank.

A septic tank or drain pit should be located at least 3-4 meters from the shower and exceed the volume of the tank by 2 times in volume.

A drain for a summer shower, a simple option is a ditch, the bottom of which is sent with PVC film. But it's better to use plastic pipe through which the waste water goes into the septic tank.

Wooden shower floor

Two common options:

wooden floor in the shower. To operate such a floor, you need to do it under the shower drainage system. To do this, you need to dig a recess equal to the area of \u200b\u200bthe shower to a depth of 300 mm. The pit is filled with rubble and sand. A wooden pallet or grate is installed on top;

concrete floor. In this case, a deeper recess is dug - up to 400 mm. A pillow of crushed stone and fine gravel is laid on the bottom, and concrete is poured on top. So that the water can freely leave the shower, you need to pour concrete at an angle, and use a pipe to drain.

Tip: If in the future you plan to make a wooden shower for a heated cottage, use a concrete floor.

Construction of a wooden shower frame

Since the shower will be made of wood, the same material will be used for the frame.

Considering that the water tank located at the top of the shower will be quite heavy (when full), and the shower structure itself is subject to wind load, it is better to choose a bar with a section of 100x100 mm for the racks.

Tip: if you plan to hang wooden door it is better to immediately provide additional racks. They are buried in the ground at a certain distance from each other. The gap is equal to the width of the doors plus the width door frame, plus a gap of 2-3 cm.

To install vertical racks, you need to drill (or dig) holes up to 1 m deep. The depth depends on the location of the shower. If in a fenced area you can 0.5m. A sand and gravel pillow is laid at the bottom of the pit, and racks are installed. In order for the tree to last longer, it must be pre-treated with resin, machine oil, drying oil or wrapped in roofing material. Next, the racks are concreted.

To protect the racks, you can install metal blanks with a size equal to the parameters of a bar or cylinder, concrete them. Then hammer a tree into them.

Tip: the front struts should be made 50-100 mm longer than the rear ones. Thus, during rain, water from the roof will flow towards the back wall of the shower.

After the concrete has dried (solidified), you can proceed to further construction.

All racks, set strictly according to the level, are connected by the upper and lower trim.

Advice. To make the top harness easier, you can assemble the frame on the ground, place it on supports from above and secure it with capercaillie bolts.

The material was prepared for the site www.site

Consider when planning a slatted wood floor bottom trim will serve as a support for the logs, so it needs to be well fixed. With a concrete field, the lower trim serves to fasten the wood trim.

A roof is covered on the upper trim, and a tank is installed.

Building a wooden shower with your own hands - video

the tank must be chosen in a dark color, it will attract the sun's rays;

wall thickness affects the rate of heating;

Advice. To make the tank heat up faster, cover it with a sheet of glass or make a polycarbonate greenhouse.

the tank must be resistant to frost. Otherwise, it will have to be removed for the winter;

for safety, place the tank behind or to the side of the cab;

when planning a heated shower, give preference to a metal tank;

Tip: installing a float in the tank will allow you to take water from the top of the tank, it warms up better there.

to refresh one person needs at least 20 liters. Consider this when choosing the volume of the tank;

Advice. To ensure the best water pressure in the summer shower, the tank must be installed vertically. If the heating rate is important, install the tank horizontally.

Installation of the tank does not create difficulties, the main thing is to securely fix it on the roof. Before installation, you need to make a hole in the bottom of the tank (barrel) for a watering can with a tap (if it is not provided by the manufacturer).

Tip: the water tank must be periodically cleaned and an antiseptic (for example, potassium permanganate) added.

Wall cladding and door installation

The walls of the summer shower are sewn up with prepared boards. The door is hung last. Following the logic of construction, it should be wooden. But wood often “leads” from moisture, so many people advise using a film curtain as a door. Of course, if you have a capital summer shower, then it is better to take care of installing a high-quality wooden door.

This is the part of the work in which you can involve children. Lacquered, painted in one color or in all colors of the rainbow, it will add zest to the overall appearance site.

Additionally, a summer shower can be decorated with flower pots or climbing plants can be planted near it.

Photo of a wooden shower for ideas and inspiration

Conclusion

Now that you know how to build a DIY wooden shower, don't hesitate to get started building and treat yourself to a few minutes of fun after a hard day!

Summer is a great time for summer holidays. It can be overshadowed by the absence of a shower, since a person, regardless of whether he works or rests, needs to perform water procedures.

If the cottage is used only in the summer, then the easiest way to organize a shower is on the site. You can make a mobile shower, or build a solid outbuilding.

Portable outdoor shower

In stores you can find a foot shower. It does not require any construction or installation to operate. As a rule, only a small container of water is needed to use it.

An existing hose is lowered into the tank, which is connected to the pump. It looks like a small rug. Water comes out through a hose with a watering can, and for it to go, a person just needs to stomp in one place.

This device is simply indispensable, as it is suitable not only for summer cottages, but also for picnics, you can take it with you on trips.

With its help, water procedures can be carried out not only on the street, but also in the house, when it is very cool outside.

To do this, you just need to put a basin and wash. Another advantage of a mobile shower is self-adjustment water temperature. Such a shower in the country is simply not replaceable.

Stationary shower

Many summer residents are interested in how to make a stationary shower. This option is quite expensive compared to the first one. However, it will serve you for many years.

Before starting construction, it is necessary to consider where the water will drain from it. It is good when there is an antiseptic on the site. It can be drained from the shower.

If it is absent, then you need to make a hole, fill the bottom with expanded clay. A family needs a pit measuring 60x60x60 cm.

If sand predominates in the soil, the walls of the recess will have to be strengthened so that they do not crumble. For this, a metal mesh or boards that are no longer needed are suitable.

shower base

As a rule, the shower building weighs little. Therefore, it makes no sense to make a foundation for it, it can be replaced with blocks. They are leveled at the same level so that the structure is level.

It is much cheaper than the foundation, and takes much less time to build, since the foundation must dry out, and the building can be erected immediately on the blocks.

Blocks should be placed 20 cm from the ground, this is necessary so that the tree does not rot.

In the event that you are going to make a metal structure, then the blocks can not be aligned at a level of 20 cm. Such a frame can be installed on ordinary paving slabs.

building

There are two types of building. The first is when the building is divided into several parts. In one part, a shower is made, in the other a dressing room or technical room where the boiler is installed.

Note!

The second type is a simple shower with a curtain, where only water procedures will be performed. Therefore, the dimensions of the soul are calculated from what kind of building is planned.

Frame types

Metal. The frame can be made of a profiled pipe, 3 mm in size. For work you need a welding machine.

Pipe joints are best welded, so the structure will be stronger. If the device is not available, then the joints can be fastened with special bolts.

Tree. For construction, you need a beam. Usually use a bar with a size of 50x50 mm. Before starting construction, it is necessary to make a drawing of the shower in the country.

shower sheathing

After the frame has been erected, the shower must be covered with material. There are no specific material standards. Everyone chooses according to his own pocket.

Let's highlight the most popular materials:

oilcloth;
the cloth;
wood;
slate;
polycarbonate.

Water tank

Absolutely any container can be used as a tank. Basically, these are metal or plastic barrels. They can be purchased at any building, country stores.

Note!

When choosing, consider the region of residence. For southern cities, any container is suitable, but for the northern regions, only metal, as it heats up faster.

shower tray

It is best to purchase a pallet ready-made, as it will have a drain that will directly merge into the pit. The pallet is made of plastic or metal. Metal will last much longer, so it is advisable to choose it.

Making a summer shower in the country is not so difficult. The main thing is to thoroughly approach the design and calculate in advance the amount of material required.

For clarity, you can consider a photo of a summer soul in the country with your own hands. It will make your stay comfortable and enjoyable.

Do-it-yourself photo of the soul in the country

Note!

Most city dwellers cannot imagine summer without summer vacations, and summer cottages without basic comfort conditions and, first of all, the opportunity to take a shower.

This is especially true on a hot summer day, when life-giving moisture helps not only wash off dust and sweat, but brings us back to life, giving a feeling of freshness, cleanliness and good rest.

A country street shower has long ceased to be a primitive structure with a bucket of water and a ladle instead of a watering can.

It offers summer residents the widest choice of materials for construction - whether it is an inexpensive functional building or an exclusive architectural form, capable of becoming a real decoration of a suburban area.

Garden showers - construction options and functionality

Basic design any summer shower consists of several essential elements:

shower cabin is a frame made of wood or metal, sheathed, as a rule, with a light, durable, opaque material (board, corrugated board, awning)
Floor with drain system- wooden, tiled, concrete, with a shower tray. Two drain options are used - into a sump (gutter) or equipped with drainage for natural absorption of moisture into the soil directly under the shower floor
Water tank– minimum volume 100-200 liters for a family of several people
Shower equipment: a set of hoses for filling the tank with water, a faucet, a sprayer (watering can), a shelf for soap and shampoo.

Materials for building a shower: pros and cons

For construction country shower you can use a variety of materials- specially purchased and those that are at hand or left after the repair of a house or apartment:

wooden shower- classics of the genre! The frame of such a structure is made of timber and covered with coniferous and hardwood wood. For outer skin use a planed board, euro lining, block house, ordinary or profiled timber. Undoubted advantages such a shower is a natural, environmentally friendly material, the incomparable aroma of sun-warmed wood, strength, reliability and aesthetic appeal of the design

Recommendation! One of the most common cladding materials is lining - a thin planed board. It has several varieties: ordinary, eurolining - profiled board with special spikes and grooves for connection, block house - decorative board with a profile of rounded timber, imitation of timber - a panel of planed boards.

Shower from corrugated board – inexpensive option, especially if the material remains from previous construction works. Galvanized profiled sheet with a protective and decorative coating - very durable, fairly rigid, durable material with excellent anti-corrosion properties, which is important in constant contact with water. Decking is mounted on a frame made of shaped pipes and a corner. Such a structure will always look neat, fit well into the natural landscape of the suburban area. Unfortunately, this shower can only be used in summer, as the metal is thin and the cabin cools down quickly.
Can be built polycarbonate shower– cellular sheet building material from the thermoplastic family. It has unique characteristics - durable, lightweight, plastic, does not require additional protection against rust, has a translucent or matte texture. For the shower, it is better to choose matte polycarbonate, it is more suitable for intimate water procedures.
Brick shower- a solid building that will serve you not only in summer, but from early spring to late autumn. This design requires strong concrete foundation, a reliable drain system, provides for heating water. Walls can be made of silicate or facade brick, inside the shower, most often, sheathe vinyl siding or a tree. Cons of a brick shower - significant costs and long construction time
The mobile version of the summer shower is metal structure from profile pipes covered with an awning. It is easy to make it yourself by welding or bolting a frame from a metal profile and covering it with a moisture-proof fabric
You can build an outdoor shower at virtually no cost, using, as they say, production waste. These include wooden pallets or pallets for oversized cargo. After use, the pallet is subject to recycling, but in the hands of craftsmen it can acquire a second life. Pallet boards are perfect for sheathing a summer shower, building shelves, benches and other garden utensils.

Heated garden shower

For those who live in the country not only in the summer months, but in spring and autumn, they prefer to swim in warm water both on a sunny day and on a cloudy day, the best option there will be construction heated shower.

What should be taken into account when constructing such a building?

Firstly, the shower must be warm enough to take water procedures in it both in April and in October. In the winter months, it is still better to take a bath.

Of the materials for construction, brick, wooden beams are ideal, everything else will have to be insulated.

Secondly, needed permanent source water, from which it is fed into the tank automatically or manually. It can be a water supply, a well, a well.

Thirdly, an important condition is availability of electricity, because it is it in most cases that serves as a source of energy for heating water.
Which options for heating water in the shower are most often used:

Electricity. Special tanks are sold with built-in electric heaters (heaters), the power of which determines the rate of water heating - the more powerful, the faster it heats up. Having basic skills in working with electrical appliances, the heating element can be mounted in the tank yourself
Firewood. To heat water, you can use a time-tested steel hot water tank on wood - titanium. It's both reliable and cheap.
Gas. Water can be heated in a geyser using liquefied bottled gas.

Multifunctional buildings - two in one

If there are no buildings on your lot other than country house, a practical and useful structure can be economic blocks with several departments:

Shower with toilet- the two most necessary "strategic" nodes. It is with them that it is worth starting the improvement of the summer cottage. Building them in a complex will help solve both problems at the same time and at the same time save money. Optimal material- wood or brick
Shower with dressing room, which plays the role of a kind of dressing room. Here you can leave your clothes without fear of splashing them with water, get dressed calmly, put yourself in order
shower with necessary for housewives - lovers of home conservation and cooking in nature. A multifunctional room will help to process the grown crop, it is comfortable to cook in it even in the summer heat. In addition, you will not once again heat the house, keeping it pleasantly cool.
Shower with laundry- a very convenient combination of functionality, especially if there is a water heating system.

Choosing a place for a country shower

In order to choose the right place for the future structure, it is necessary to take into account several factors:

The place must be open and unshaded by trees - after all, even if the heating option is provided, we rely on the natural heating of water by solar radiation. In addition, the structure must be well ventilated and dry to avoid dampness and mold.
If the site has a drain pit, a septic tank (septic tank) or a gutter, it is necessary consider a convenient drain option using pipes or a hose
An important point when choosing a place for a shower is water source location. It is necessary to predict the tank filling system: manually using buckets, using a pump and a hose, or provide for automatic water supply.

Having determined the optimal place for the device of a summer shower, you can proceed to its construction.

Do-it-yourself shower construction technology

Summer shower dimensions

When determining the size of the shower, it is important to remember that its area should not be less 1 m2, the most suitable height is 2–2.3 m.

Specific dimensions are determined based on the dimensions of the building material, in such a way as to minimize waste. For example, when building from a standard 6-meter beam, you can design a shower 2x2 m or 2x3 m.

Preparatory work: arrangement of the drain

Option 1. We provide for draining into a gutter or a special sump. For this we do base markings shower in accordance with the selected dimensions.

We remove the soil from the marked place approximately to the depth of the shovel bayonet, line the pit with roofing material and fill it with a layer of rubble in 15–20 cm.

We mount immediately water drainage system: we put a piece of hose or sewer pipe in the pit and bring it outside the perimeter of the shower. From above we install a pallet with a drain (it is better to purchase a ready-made one), and connect it to the pipe.

Beyond the soul sewer pipe can be laid in a trench or on the surface. Instead of a pallet, the floor can be concreted or tiled.

As a sump (septic tank) for soapy water, you can use eurocubes – plastic container for bulk and liquid cargo, tied with a metal grate.

The undoubted advantage of these containers is that the volume is not less than 1000l and durable plastic. By connecting two eurocubes to each other and burying them in the ground along the neck, you can get a home-made purification plant for settling waste water.

Option 2. We mount the drainage system directly under the shower. We dig a hole at least half a meter deep, fill it in 40–45 cm large rubble, pieces of brick, stone.

We finish everything with a layer of small gravel in 5–10 cm. Water will naturally soak into the ground.

On this base we install a wooden grate along the width and length of the shower, which will play the role of a floor. Lattice height 7–10 cm, we make it from wooden blocks the size of 2x3 cm or board-twenties wide in 8–10 cm.

The optimal size of the gaps between the bars - 0.5–1.0 cm, a longer distance will cause inconvenience during operation. The material for the grate must be cut and polished with high quality so that there are no burrs.

Building a shower cabin with your own hands

The next step is to make frame.

At the corners of the shower, we concrete four racks from a profile pipe with a size of 50x50 mm or 40x60 mm, we provide one more for a canopy of a door.

From the same profile we make horizontal lintels connecting vertical racks around the perimeter - above, below and in the middle. It is best to carry out the construction by welding - this will ensure sufficient rigidity and stability of the structure.

Finished frame cover with anti-corrosion compound and paint. As a sheathing, we use any inexpensive, lightweight and durable material - a board, corrugated board, siding, etc.

We fix it all with self-tapping screws. We hang the door- it is better to buy ready-made.

We strengthen the roof, using profile pipes as a log, we mount on them roofing material- slate, metal tile, ondulin. Place a container of water on top.

Installation of shower equipment

When choosing a water tank, size matters - best option 150–200 l, the shape is better flat for faster heating of water, the color is black or dark for the same purpose.

Special tanks have finished holes for a shower and water intake, so it remains only to connect the hose to the supply, install a faucet and a watering can or sprayer.

If we use an ordinary barrel, we drill a hole in the bottom, insert the squeegee - a piece of threaded pipe, install a tap, put another squeegee and connect the sprayer (watering can).

capacity needed be sure to close so that debris and leaves do not get into the water.

Do-it-yourself wooden shower for a summer residence

Foundation construction

To make the design more solid, it is desirable to make foundation.

To do this, we dig a ditch along the perimeter with a width of 15–20 cm and depth in 30–40 cm. Next, we make the formwork for the foundation.

From the boards we knock down and install the box ( height - 15–20 cm) along the perimeter of the shower, focusing on the prepared trench.

We fill the ditch and formwork with concrete mortar. For its preparation 1 bucket of cement M500 take 4 buckets of sand, 5–6 buckets of crushed stone, 1.5–2 buckets of water.

For the strength of the foundation in the ground part of the foundation you can install reinforcement or pieces of thick wire. Align the fill in the horizontal plane using building level. The approximate height of the finished foundation is 10–15 cm. After the concrete has hardened, we remove the formwork.

Shower cabin installation

Along with the foundation at the corners concrete pieces of rebar, on which we fasten wooden supports from a bar. We mount the frame from the same lumber.

The choice of wood for sheathing the frame is quite large. Best for heated shower timber- the room will be warm, breathable and cozy.

For summer version you can buy euro lining, block house, imitation of a bar from coniferous trees.

Essential oils and resins contained in wood have bactericidal properties, are a natural air flavoring - therefore, washing in such a shower is not only pleasant, but also useful.

We fasten the boards with self-tapping screws to the horizontal cross members of the frame. For better ventilation in the upper part of the shower between the walls and the roof along the perimeter we leave a gap of size up to 10 cm.

Roof and floor of a wooden shower

The roof is easier to make flat, lean-to.

To ensure rainwater runoff, we make a slight slope by raising one side of the roof to 10–15 cm. Depending on the size of the shower, we use several bars the size of 10x10 cm(minimum 2).

On the bars with the help of nails we fasten a wooden formwork from a board with a thickness of 20 mm, forgive it with roofing material or other waterproofing material, we cut with slate, metal tiles, ondulin, etc.

Advice! In the manufacture of the roof, we make all the holes for pipes and hoses at once, so that later we do not have to cut them out, violating the tightness of the roof. To keep the tank on the roof level, fasten a wooden block under it from the lower side.

The floor in the cab can be made of terrace board, teak, alder, linden or larch are best suited. Leave a gap between the boards 5 mm for water drainage.

Where can I buy a garden shower

If you have neither the time nor the desire to build a shower in the country with your own hands, you can trust professionals or purchase a ready-made design.

Retail trade networks of building materials and household appliances, including online stores, offer a wide range of shower enclosures made of wood, polycarbonate, fabric coverings and other materials that are assembled on suburban area during few hours.

Most common brands and their value:

German garden showers are very popular with summer residents trademarks Karcher and Gardena (Karcher and Gardena). This device can be used both in the booth and on open space(on the lawn, by the pool), setting it on a special tripod. The shower is connected to a tank by means of a hose, from which water is supplied by a pump. garden shower It has several positions for spraying water, is adjustable in height, and is turned on at the touch of a button. Such a shower costs from 1800 to 2250 r
Garden shower step(sometimes called "toptun") is useful in field conditions when there is no stationary shower. It supplies water from the tank with the help of a foot pump, actuated by trampling feet. The shower is very economical and allows you to wash yourself with minimal water consumption. Estimated cost - 1250–1500r
summer souls "Zelenovka", "Aquatex", "Garden"- this is an opportunity to inexpensively purchase a full-fledged shower cabin, including one with heated water. Showers are installed directly on the ground or on a prepared base. Lightweight frame included steel pipes, lining made of tarpaulin or other waterproof fabric, plastic or steel tank with a capacity of 110–220 l, wooden pallet, electric heater. The cost of a shower without heating - 5300–6500 rubles, with heating - from 6000 to 8500 r.

When you decide to build an outdoor shower, you are making country rest more comfortable, joyful and desirable for you and your family.

You can see detailed information on how to build a summer shower in the country with your own hands in this video instruction.