Arched openings in the house. Arch design in the interior of the apartment

03.09.2016 27782

When implementing rooms, the question often arises of what to do with the doorway. Classic variant. Alternative way is the installation of drywall or wood. Other design options are less common. Consumers try to decorate with plaster or wallpaper. However, few know how to decorate the arch in the apartment with their own hands.

Arch installation

If the owner of the apartment has decided, then initially you need to make a sketch of the arch and free the doorway. If necessary, you can increase its area, but the final decision will depend on the shape and size of the arch. If the product is made of drywall, then you need to purchase the appropriate building materials (dowel, screws, drywall, self-tapping screws). Then the owner needs to measure according to the sketch. Based on the dimensions obtained, a frame is made. The necessary pieces are cut with metal scissors. After that, you need to fix the profile around the perimeter of the arched opening with special dowel screws.

Next, a drywall sheet of the appropriate shape is prepared. It is desirable to cut the workpiece with a jigsaw. In this case, drywall must be attached to a metal profile on both sides of the arch. Self-tapping screws are used to fix the workpieces. The distance between them must be at least 15 cm. To seal the surface of the arch of the profile blank. For an arched arch, you need to make an incision on the profile so that it can be bent. It is advisable to make the distance between the cuts no more than 12 cm. After that, the workpiece must be attached to the drywall from the inside using self-tapping screws. The profile blank is attached in the same way on the other side of the arch. As a result, the workpiece should repeat the contour of the previously cut drywall sheet.

The final stage involves fixing the bottom element. First you need to measure the size of the required strip with a tape measure. Then the corresponding piece of drywall is cut out. To bend the workpiece, you need to make cuts from the inside. The interval between them can be 7-10 cm. After that, you can screw the workpiece to the metal profile, which is screwed on the inside of the side strips of drywall. Now you can open. To perform the work, the following tool is required:

mount;
Roulette;
Level;
Scissors for metal;
Perforator;
Jigsaw;
Screwdriver.

Finishing the arch with plaster

After completing the rough work, it is necessary to finish the drywall arch with plaster or putty. This material allows you to fill in the voids and even out the curvature formed on the arch. Similar work is done with a spatula. The mixture is applied to drywall and evenly stretched along the entire length of the arch. Usually plastering is carried out in several passes. Then you need to let the plaster dry. On the eve of applying the finishing putty, you can make a small cleaning of the previous layers. For this, special abrasive meshes must be used.

As for the side walls of the arch, they can be immediately finished with finishing putty. The exception is the drywall joints with the wall. Here you need to put plaster mesh, and then cover it with plaster so that cracks do not form in the future. To finish drywall corner joints, you can use an arched corner or reinforcing tape.

Before laying this material, it is necessary to apply a thin layer of finishing putty to the corner of the arch. Tape should be evenly distributed on both sides. corner connection arches. To prevent the material from wrinkling, cuts can be made every 10 cm. Last layer putty should be extremely thin. After it dries, the final cleaning is done with a fine-grained abrasive mesh. When finishing an arched opening, tools are usually needed that are different from those used during the installation of the structure. Here you only need a spatula and a clerical knife.

Finishing the arch with decorative plaster

Another finishing option is decorative plaster. This material is applied exclusively to the prepared surface. To do this, you must first plaster the arched opening and fill in all the voids. How to do this is described in the previous section. Wherein finishing putty it is not necessary to apply to the arch. However, before applying decorative plaster be sure to prime the pre-plastered surface. The primer improves the adhesion of two different building materials. The drying period of the primer is from 4 hours to a day. To create a relief on the applied decorative plaster, you must use a grater, sponge or spatula. As a result of the drying of the applied material, the arch will need to be painted. For this, special paints are used. But, before painting, you need to cover the area again with a primer.

You can paint the surface of the arched opening with a roller or brush. It is desirable to apply paint in two layers. If necessary, you can use different shades. If the paint is applied with a short pile roller, then the owner can achieve a bark beetle type effect. Because unpainted grooves create a specific pattern. To enhance the effect, you can add a special dye even at the stage of applying the plaster, and when painting the walls, change the original shade. After the paint has dried, you can cover the surface with beeswax. This will give the arched opening a kind of matte sheen.

Wallpapering on the arch

Next, the owner needs to trim the arch. Wallpaper is one of the finishing options. The color of the material is desirable to match the color of the wallpaper on the wall. Framing technology is quite simple. Before you decorate the arch in the apartment with your own hands, you need to prepare strips for decoration. Then you should prepare wallpaper glue. By consistency, it should be thicker than when gluing wallpaper on the walls. This is necessary to increase the term, so that you can move the wallpaper strips if they are with a pattern. It is advisable to start gluing the strips on the wall near the arched opening. Then you need to lay a strip that will cover part of the arch opening. The protruding remnants of the material should be cut off with a clerical knife, but in such a way that an allowance of about 25 mm remains. After that, you need to make cuts with an interval of 20–25 mm, bend the wallpaper strips and glue them to the arched plane.

Similarly, you need to glue the second side of the arch. To complete the gluing of the vault, cut a strip equal to the width of the arched opening. However, the length of the workpiece must be longer so that the pattern can be adjusted. The cut out strip of wallpaper must be glued to the inside of the arch. To avoid the appearance of bubbles under the wallpaper, you need to carefully smooth out the glued strips.

Archway painting

You can make an arch with your own hands ordinary wallpaper or wallpaper for painting. If the owner of the premises chose the second option, then after the laid material dries, it is necessary to paint it. To wallpaper the arch with wallpaper, you will need the following tool:

Pencil, ruler;
Stationery knife;
Glue brush.

When painting wallpaper, you will additionally need a paint roller.

Arch decoration with decorative stone

You can also decorate the arch with decorative stone.

This type of decoration is one of the laborious ways of framing the arch.

The main load falls on the decoration of the vault. At the same time, decorative stone is convenient in laying, as it does not require a perfectly flat surface. Therefore, there is no need to plaster the structure, except for large holes. But, if you need to decorate a drywall arch, then the stone should not be too heavy so that deformation does not occur. Before laying the stone, the surface must be primed. Installation can be done with glue or liquid nails. The first stone must be laid from below in such a way that it overlaps the junction of the gypsum and the wall. When laying stone along the arched arc, appropriate pruning should be carried out. Grinding the cut is done with a stone file. To seal the seams, you need to use a special solution. As you can see, framing arches with your own hands, although it requires certain skills, is, however, quite feasible.

You also need to make sure that the entire list is necessary tools. The decoration of the arch depends on the capabilities and taste of the particular owner of the apartment. but the best option there will be decorative plaster. This material allows you to use different textures and experiment with shades of colors.

With the rapid entry into the interior fashion of studio apartments and combined spaces with the effect of visual zoning, various arches have become an integral attribute of many interiors.

Initially this architectural element builders erected as a ceiling for through or blind openings in the walls, as well as to create a side spacer, but modern designers have looked at it in a completely new way and now very often use the arched frame as a decorative element during the implementation of various design projects.

7 ways to improve the arch in the apartment

If your house or apartment already has an arch, you can decorate it in an original way even without the help of specialists, making it an expressive accent in the overall interior composition.

We offer several simple ways to frame arches that you can implement with your own hands:

paste over with textured trellis or wallpaper with an original pattern;
lay out with natural or artificial stone;
ennoble by installing overlays of precious wood around the openings;
decorate with decorative plaster;
paint and apply a stencil;
veneer around the opening with mosaics or mirror tiles;
trim with polyurethane moldings;
decorate with stucco.

Any of the above options does not require special knowledge or special skills - it is enough to accurately determine the method of decorating the arches in the apartment and stock up on the most necessary information before starting work, consumables and tools. In such cases, watching several video tutorials helps a lot, in which the secrets of a particular type are revealed. construction works or technological processes.

An affordable and inexpensive way to decorate an arch is wallpapering

Spectacular and, at the same time, accessible to absolutely everyone, the design option for openings is framing the arches with wallpaper. For this purpose, you can glue textured, colored tapestries or glue the arch with panels with an original, eye-catching print. It looks very cheerful on a neutral background of the walls of the opening, glued bright wallpaper. The main thing is to choose the right color solution, echoing color scheme with other interior accents in the apartment, for example, textiles. It is permissible in the process of finishing the opening to glue several different types tapestry or, if the apartment has several arches, glue them contrasting wallpaper, but at the same time it is desirable that they be from the same collection or simply carefully matched to each other.

There are no special instructions on how to wallpaper the arch with wallpaper. The main thing is to strictly follow general recommendations regarding gluing exactly the type of trellis that you purchased. Usually they are written on each roll. Also a couple useful tips about how to glue the arch with wallpaper, sellers of shops selling wallpaper can give.

To cut off excess trellis when gluing, it is best to use a large breadboard knife, but it is advisable to trim the edges of the panels only after the glue has dried well, since soaked paper can simply tear under the blade, and as a result, the work done will look sloppy. It is advisable to protect the ends of the glued arch with a special flexible profile made of plastic, otherwise there is a risk that the tapestries will quickly fray at the protruding corners. It will not be superfluous to stock up on the wallpaper used for pasting for the future - an extra roll will always come in handy to update a dirty place without completely re-gluing the entire arch.

Framing the arched opening with stone or wooden lining

In a classic or modern eco-interior, arches made of decorative stone, as well as structures decorated with precious woods, will be very appropriate.

A big plus of decorating with a stone is that it can ennoble an opening of any shape - from a simple rectangular to a semicircular and even asymmetric. It will be more difficult with wooden overlays - not every carpentry workshop has required capacities and equipment for working with bent wood, so if such a master can be found, then his services will cost much more than usual.

To reduce the cost of equipment, stone arches can be used instead of natural ones for laying out an opening. artificial material, which not only looks no worse than the real one, but also has great wear resistance.

In both cases, before proceeding to frame arches and openings, it is necessary to carefully prepare the surface for decoration, leveling it and ensuring maximum symmetry about the axis (except for asymmetric structures), since the decor will make the initial construction flaws even more noticeable if they are not eliminated in time .

Arch decor with stucco and polyurethane elements

Beautiful arches in the apartment can be made with the help of such decorative elements as plaster moldings, polystyrene foam or polyurethane moldings. But here you should be very careful: such decor for the arch is only suitable if the entire interior in the apartment is designed in such styles as baroque, rococo, biedermeier. Agree, this design option will look very ridiculous if the whole dwelling is decorated, for example, in country style, loft or minimalism.

In specialized stores, ready-made stucco molding for the arch is sold: rosettes, baguettes, friezes, moldings, which you just need to correctly select, harmoniously place on the opening area, glue, putty and paint. There is a stereotype that stucco decor must be white, but this is a complete delusion. Elements can be painted in any color, although stucco molding painted in gold, silver or bronze with the effect of antiquity (uneven staining of the surface, creating the illusion of wear) looks the most noble in classic interiors.

You can talk about how to ennoble the arch on a few more pages. best advice in this case, armed with photographs of your favorite examples of openings, turn on your imagination and not be afraid to experiment, and then everything will work out for sure.

Doorways are necessary element in every room, but despite the standards (rectangular shape), many quite often choose another option - the arch. To create it, you need to use the usual recommendations of the builders, but an important part is its design, after which the arched passage will acquire its beauty. To date, the decoration of arches decorative stone very common, as everyone tries to develop and implement original ideas thanks to which even a simple doorway will decorate the whole room.

In this article we will tell you how to decorate the arch with your own hands in the apartment, we will give step by step instructions as well as video and photo materials.

Nuances during installation

In most cases, arched passages from room to room are planned during construction, but it is also possible to create such a passage after construction. In this case, it is worth considering tips for installing drywall arches. When changing the layout of apartments and houses, interior walls are demolished and new ones are erected, while profiles and plasterboard sheets are used to install partitions.

Since the aluminum profile is easy to install, it is perfect for structures of any shape. It is also worth noting that drywall sheets can also be shaped, so they can be mounted on a rounded profile. Besides door arches it can also be used to decorate small niches in the wall, but in this case it is several times more difficult to mount the structure.

When choosing materials for decorating drywall arches, it is necessary to carefully consider the details and approximately determine the weight of the structure so that it can withstand the load.

Decoration Materials

For decorating the arch, a wide variety of materials are used, which are available in specialized stores. Among the most common it is worth highlighting:

mirror;
stone (natural, artificial, decorative);
mosaic;
ceramic tile;
textile;
wallpaper;
plaster;
Cork;
plastic;
tree, etc.

In fact, the material can be absolutely any, the main thing is that it is combined with the overall interior, and also well and securely fastened to the arch itself.

When choosing a finishing material, do not forget that it must be combined with several rooms at the same time, since such openings combine them into one.

Plain and cork wallpapers

Most often, arches are trimmed with simple and cork wallpaper. To do this, you will need a standard set of tools: wallpaper, scissors, ruler, pencil, glue, brush. All dimensions are measured and transferred to the wallpaper, the elements are cut out, and then they are glued end-to-end.

According to the advice of experts, it is first necessary to paste over the walls, and then the arched passage, while Special attention give joints that should converge as much as possible. When making openings in an apartment, it is necessary to take into account the humidity and temperature in the rooms in order to choose the right material.

Cork is an ecological material, as it is made from wood. In specialized stores, you can choose both wallpaper and panels that are glued to acrylic glue.

Having finished the arch with a decorative stone, you can create a good design. But it is quite difficult to carry out all these time-consuming processes on your own. However, the stone is distinguished by high performance properties, durability, and a universal pattern that is perfect for any interior.

When making interior openings, it is necessary to level all surfaces and putty them in order to eliminate defects and irregularities. After the primer is applied. It is necessary to start laying at the joints, while moving up, and inner side arches should overlap the outer. If necessary, extra centimeters are cut off with a grinder. After laying all the elements, the openings are filled with a special grout (the color is chosen correctly).

To fix the decorative stone elements, you can use liquid nails or a special cement-lime-based adhesive.

Molding and corner

Quite often, other elements are used in conjunction with wallpaper or colored plaster, for example, they complement the composition with a molding or corner. Now in stores you can find a fairly large assortment of similar products, namely molding made of metal, polyurethane or gypsum. This variety allows you to complement any interior. original elements. Attaching them is very easy. They are installed at the ends of the arch on both sides using conventional liquid nails.

Finishing the openings of the arches with a corner occurs in the same way. Corners can be made from a wide variety of materials:

plastic;
tree;
metal;
aluminum;
PVC, etc.

This is how the polyurethane molding is glued:

In fact, the corner performs several functions at the same time: it is separate element decor, combines several types of finishes, and also protects the corners from scuffs and possible mechanical damage.

Mosaic

Another fairly common decorative material to decorate the arched doorway is a mosaic. Its range is very large, as manufacturers use innovative technologies and modern equipment, which allows you to create a mosaic of various materials:

glass;
ceramics;
metal;
concrete;
tile.

To finish the arch with mosaics, it is necessary to prepare the decorating material, as well as adhesive solution. In specialized construction stores, ready-made compounds or dry mixes are sold, which must be diluted with water according to the specified proportions. Glue is applied both to the mosaic itself and to the wall, but in a small amount and using a notched trowel.

Do not forget that when laying the mosaic, you must adhere to the pattern, if any, so as not to disturb the composition.

You can decorate the arch with the most different materials and even an apprentice can do it quite well. The main thing is to decide on the type of finishing material, as well as to study the technology of its installation. If you have questions about the decoration of the arch, then write comments to the article. Maybe you have additional tips newcomers? Write them, your experience may be useful!

Video

If you want to finish the arch with plaster, see how to do it:

Photo

An arched opening is a structural and decorative element of a wall or partition. Arches can have a wide variety of shapes, giving the openings smooth lines.
Such openings are often the main decoration of the interior, but for this they must be finished with high quality and taste. We will talk with you about what materials are used to finish the decorative interior arch and the wall adjacent to it, and how to do it yourself.

When private house just under construction, the easiest way is to design right away arched openings and fulfill them during the construction work. In multi-storey construction, arches are designed extremely rarely, especially since modern apartment after the delivery of the house, it is often a large studio room.

Arches in load-bearing walls

If you want to have an arch instead of a standard rectangular opening in a load-bearing wall, you will have to think about it seriously, and our small instruction will help you.
So:

Let's say you live in brick house and want to make an arch where you have an interior door. After removing its box, you will see a transverse concrete jumper above your head.
Its function is to strengthen the wall in the place where it has no support, namely, in the opening.

You do not need to be an expert in the field of construction to understand that this jumper cannot be removed - it will only be possible to widen the opening a little. That is, a high round arch, in this case, you will not succeed, it will be slightly lower than the height standard door, and approximately the same shape as in the photo above.
Well, if the height of the openings in your apartment is 2.1 meters, that is, it corresponds European standard. Because the domestic standard provides only a two-meter height.

Before it's done decorative trim interior arch, the perimeter of the opening needs to be strengthened. To do this, use a steel channel, from which the letter "P" is welded - its vertical racks take the load from the wall.

Only after that the arch will fit into the given rectangular opening. To create the desired configuration, you need to make a frame from the usual ceiling profile.
Notches are made on it, allowing it to be bent in the desired radius.

Watch the video to better understand the process of this work. After the frame is ready, you can proceed to the sheathing of the arch body.
For this purpose, drywall is most often used, but fiberboard and even plywood are quite suitable - a lot depends on which finishing material will be used in further processing.
V panel house doorway is a recess in the wall panel provided at the time of its manufacture. Naturally, the panel is designed for a certain load, so it is impossible to violate not only the height, but also the width of the opening.

You will have to be content with the size of the arch, which as a result you get. But you do not need to perform its reinforcement with a channel.
It is enough to choose a more durable finishing material, for example, solid wood.

Arched partitions

Few people dare to punch an opening in a partition, even in a brick one. Especially in the place where it was not there before - this is a very time-consuming task.
So:

It is easier to remove this partition altogether and build a new one. Many do just that, making redevelopment of the apartment. You can contact a specialized company and order interior arches with decorative trim.

Most often, firms offer arched partitions made of solid wood or MDF. As for their design, here the ideas of manufacturers are almost inexhaustible: geometric shapes and smooth lines, slotted gratings and carvings, colored stained-glass windows.

And if you want the price of the arch to be budgetary, you should stretch your imagination, look for possible options and try to do it yourself.

Plasterboard partition with an arch is frame structure. Its frame is also made of aluminum profile, which is sheathed with sheets of drywall.
After that, the finishing of the arches and partitions is performed. In the same way, wall arched niches are mounted, which do not zone the space of the room, but only decorate it.

Some types of arches

Decorative decoration of the arch in an apartment or a private house can be made with almost any materials - who and what has enough imagination.
So:

Various accessories come to the rescue in this matter: decorative moldings, plastic corners they are more commonly used in budget options finishes.

In this case, you can not think for a long time how to frame the arch, but simply plaster and paint it in the same way as the whole room. To archway highlight, it can be painted in a different color, and the end ribs can be trimmed with a decorative molding.

Polyurethane arches

So:

Huge popularity in interior decoration, including interior openings, acquired polyurethane today. It's tight flexible material white color, from which stucco is made for decorating ceilings, gables of houses, cornices, a frieze, and, of course, elements for decorating arches, columns and pilasters.

The cost of such a finish is an order of magnitude lower than, say, decor using wood or stone. Installation of polyurethane elements is easy, using ordinary glue such as "liquid nails". In this case, no additional decor is required, but if desired, the arch can also be painted.

In this finish, there are options. The arch can be fully lined with polyurethane - not only the end parts, but also the outer sides. Moreover, its vertical racks are often designed in the form of square or round columns with a bell.
And you can only make an edging of the opening, as in the picture at the beginning of our article.

Stone in the decoration of arched openings

A classic in the decoration of arches can be considered their lining with a decorative cane. On arches located in openings bearing walls or monolithic partitions, you can use natural stone.
Hollow plasterboard partitions they may not be able to withstand such a load, therefore, in the decoration of their openings, it is better to use an artificial stone, and even better - a flexible acrylic tile that imitates the texture of a stone.

So:

Among the many types of natural stone, the leading positions in the decoration of arches are occupied by: travertine, slate, shell rock, and, of course, marble and granite. The texture of the stone can be emphatically rough and unfinished, or beautifully polished, giving it an exquisite shape.
It all depends on the style of the design of the room, as well as its architectural and functional features. The use of natural stone in the lining of arches is an elite way of finishing, which, of course, is reflected in its cost.

Artificial stone is made on the basis of any binder: gypsum or cement. To design an arch on a plaster screed, it is better to take a stone on the same basis. Some artificial analogues are practically indistinguishable on appearance from natural stone.
In addition to the binder in production artificial stone use expanded clay or perlite, which makes it so light. Well, modern dyes, as well as the technology of their use, give the stone a look identical to natural.
The most interesting thing is that you can make such a stone at home. This will allow you to save a lot on finishing, especially if you want to clad not only the opening, but also the corridor (see Finishing the corridor with stone: types of material).
All you need is a few sample stones and liquid silicone to cast the mold. And for the production of the stone itself, there are ready-made balanced compositions for sale, which are only diluted with water and poured into molds.

It is even easier to use flexible acrylic tiles to finish the arch and the area around it. Our example shows an arched version of the window, which may well be doorway, since there is no window sill zone, and the vaults of the arch rest against the floor.
Window slope lined natural stone, and the inside of the wall with acrylic tiles. Very decorative arch special fasteners fixing the curtain. This design is also quite suitable for decorating arched niches, the ends of which can also be pasted over with flexible tiles.

Brick arch decoration

By the way, such a tile can imitate not only the texture of a stone, but also a brick. Alternatively, clinker tiles with such a texture, or facing bricks, can be used in the lining of the arch.

Wall decoration around the arch

As for the decoration of a wall with an arch or a partition, then the design options are very diverse.
And here are a few of them:

Emphasize beauty arched partition decorative relief plaster will help. It looks especially harmonious when the arch itself is lined with stone.
As an elite finishing option, a composition obtained by applying Venetian or microcement plaster on it can be made on the wall. You cannot do this work yourself, for this you need certain knowledge and skills.
But the beauty of this decor will not leave anyone indifferent.

You can also get a relief on the wall with the help of various types of wallpaper: textured, textile, fiberglass. There are options for wallpaper with veneer of stone, wood, bamboo, cork applied to them.

Wallpaper is often paired with wood wall panels, which can also be used to decorate the end of the arch itself, as shown in the example above. In more cheap option these can be MDF panels mounted at the bottom of the wall.
In this case, the border between the panels and the wallpaper is closed with a decorative molding.

Generally, different kinds panels are great for creating an arched partition design. In addition to the above options, this includes Wall panels from laminated chipboard, type-setting slatted panels from lining, laminate, 3D volumetric panels.

Laminate arch

If the arched passage is quite spacious, with a wide pier, it is often finished with the same material that the walls themselves are decorated with. And here you don’t even need to use protective moldings for the end corners.
In such an opening, they are not threatened with damage.

Arched niches and partitions not only perfectly decorate the room - they break the monotonous surface of the wall, conditionally divide the room into zones.
The interior, in which there is an arch, does not look typical. After all, the main task of design is to get away from standards.

Finishing the arch is the final stage, which will emphasize the beauty of the structure. It should be noted that exactly this work is the most important when it comes to the decorative component. Don't worry - you can do everything yourself. The main thing is to show the necessary perseverance and desire. Of course, you can not do without some experience and availability the right tools, which are selected depending on the selected finish option.

Making an arch in an apartment is a process that is carried out after the completion of the main work. The fact is that such structures are made from various materials, according to various technologies. The resulting architectural element serves to decorate the entire interior, giving it some individuality. We must not forget that the cladding can play not only a decorative role, but also perform a protective function.

A few tips to help you achieve the desired effect:

by the most in a simple way decorate the arch in the apartment with your own with my own hands the selection of an arched opening is considered desired color. Often, shades are selected that will contrast with the walls. Thus, it is possible to obtain a complete structure with a minimum of effort. This method can be used for other materials as well.
Decorating material can be matched to existing colors. For example, if the lining interior arches performed MDF panels, then it is desirable to combine them with closely spaced door leafs.
You can decorate the design with the help of various embossing, patterned ribbons that correspond to the general direction of the design.
Now stucco is becoming more and more popular. Indeed, this is a great option that allows you to emphasize the interior, decorated in a classic style.
The mosaic looks quite peculiar. Its use requires experience in laying. But if everything is done flawlessly, then the effect will be amazing.

Mosaic decoration of the arch - unusual solution noteworthy

Selection and use of materials

How can you finish the arch? Currently, there are many materials that perfectly cope with the task. We can highlight the most popular, deserving special attention:

Natural and artificial stone. It should be borne in mind that the first type requires more professionalism.
Cork. Completely natural and eco-friendly product. The price can be a major downside.
Decorative plaster. This option allows you to finish the surface so that the impression of natural stone will be formed.
Various types of tiles. They are similar in laying technology to stone, but give the interior a completely different look.
Textile. This material requires a special approach to eliminate banality and simplicity.

Of course, there are much more products for decorating arches. With a certain desire, they can go completely unusual options. So, for example, the design looks quite original, which is lined with fitted log cuts. Technologically this decision performed very simply. The blanks are cut to right size. On the one hand, a drank is carried out, which will serve as a groove for the edge of the opening. Such logs are inserted into place, fixing on self-tapping screws.

Wallpaper - simple and affordable

Indeed, this is one of the easiest ways that allows you to complete the entire process in a short time. The main thing is that the costs will be minimal.

Wallpapering - the most simple and inexpensive way archway finishes

The whole process is very simple:

If required, then before pasting the arch with wallpaper, the surface is leveled.
On a note! Before finishing the drywall arch, a layer of putty is applied to its surface. This is necessary so that in case of a desire to update the finish, the wallpaper does not have to be removed along with the cardboard.
After waiting for the applied composition to dry, the glue is prepared. It is kneaded according to the available manufacturer's instructions.
The wallpaper is cut into strips of the desired length. The sticker is carried out strictly vertically, capturing part of the opening. You should get a bend equal to 3-4 cm.
To bend the allowance, but avoid wrinkles, cut the edge into corners.
Now the most painstaking part of the work is to cut a strip that will be glued to an arcuate surface. This must be done so that the existing pattern matches. This area is smoothed from top to bottom. That is, gluing is performed at the highest point, after which the fragment descends to the bottom.

Although there are some negative factors to consider:

It is necessary to decorate taking into account the fact that such material is very short-lived. After some time, the surface may acquire yellowish tints. The feeling of novelty will disappear.
The use of wallpaper is limited to the location of the opening. They are not recommended for use for structures that are located in kitchen area. Even washable species will not save the situation.
Absence protective functions. Such a coating is very easy to damage, and from minimal mechanical impact.

Of course, it cannot be said that this way allows you to decorate the arch. But, of course, it is suitable for many situations that require the most simple and inexpensive work to be done.

Stucco - spectacular and elegant

To get a spectacular arch that attracts the eye, polyurethane stucco molding is used. This modern variety products that were previously made exclusively from gypsum. It is actively used to frame various designs.

Arch decoration with polyurethane stucco - an affordable solution with a stunning effect

This option has its own characteristics. The fact is that the finishing material is more suitable for classic interiors. If you use a polyurethane arch in modern style, then such details may seem completely inappropriate.

Installation is carried out according to the following technology:

Surfaces are leveled. All areas are well cleaned.
All dust is removed. If you leave such flaws, then gluing will be unreliable.
The treated surface must dry well. This period is used to perform markup. You may need trimming parts.
On a note! To perform trimming at an angle of 45 degrees, a miter box is used. It is important to correctly place the elements in order to avoid the appearance of docking slots.
Now you can start gluing. For this, it is used special compound, which is marked: "suitable for gluing polyurethane products." This substance is applied to the wrong side of the part, which is pressed against the surface and held. If docking is performed, then the glue is smeared on one side. It is important to remove excess immediately. The seams are treated with putty and polished.

When finishing the arch with polyurethane, it must be borne in mind that all work must be carried out with extreme care. Any defects will be very difficult to correct.

Decorative plaster - time-tested

finishing arched openings can also be done with decorative plaster. This method has its positive aspects. This is one of the few options that allows you to get an extremely individual surface that will be durable.

Some shortcomings cannot be ruled out. Thus, the coating is very difficult to restore if damaged. If the result of the work is a relief surface, then it must be constantly looked after.

On a note! It is very easy to arrange an arch in an apartment with your own hands if you use special decorative mixtures. They possess big time setting, which allows you to form the necessary texture so as to achieve the desired result.

The order of work is as follows:

Finishing arches begins with preparation the right amount mixtures. Further, it is transferred to a prepared, well-primed surface. It is important to consider that each layer must have a certain thickness. Their number depends on the chosen decorative type.
To form a relief much faster, special rollers are used.
The resulting relief is left to dry. Then covered with a primer.

Now the trimmed area can be painted. To get an interesting effect, two shades of paint are applied to the surface. One fills the cavities, the other - the protrusions.

Stone - reliable and original

Stone is a great solution that will help create your own zest in the interior. It is important to consider that it is better to give preference artificial options. They are much easier to process, and also do not require professional knowledge. The material that follows the curves of the structure looks best. In this case, an arc.

Making an arched opening with a decorative stone - stylish solution for modern interiors

Actions are performed in the following order:

Finishing the arch with your own hands begins with the fact that they prepare the coating. It is important to exclude any drops and defects.
A laying plan is being drawn up. Marking is done on the surface. Nearby, on the floor, material is laid out. This technology will allow you to immediately fit some elements, distribute them more correctly, and also avoid mistakes.
The stone is laid on glue or a special mixture. The technology allows you to create wide joints or do everything without seams.
If trimming is performed, then the cut edges must be processed.

The same technology is used when the question arises of how to finish the arch in the apartment with tiles. But it should be borne in mind that this material requires compliance with a certain sequence. If the stone can be laid "arbitrarily", then the tile is clear.

Plastic - modern and affordable

Plastic is pretty easy to work with. It is important to understand that not all panels can be bent to the desired angle. Many, especially cheap ones, break down quickly. It is much easier to veneer an arched opening plastic panels when it has an angular arch.

The following manipulations are performed:

Can be excluded careful preparation surfaces. It is important to understand that often, panels are used in order to form an opening completely. That is, they act as the main and decorative elements of the structure.
Created wooden crate. It will serve as the foundation around which everything else is built. The slats are laid perpendicular to the panels.
The arched dome is formed by dividing it into sectors. Often, the division occurs into three parts: top, two extreme fragments.
The panels are fixed on brackets, which are clogged with a stapler along the edges. All joints and transitions hide decorative corners.

Self-plating plastic arches will not cause any particular difficulties

How to decorate such a surface additionally? To do this, you can use various decorative elements that will be in harmony with the plastic.

On a note! It is not difficult to line the arch with plastic with your own hands. The main thing is not to choose the cheapest materials.

Cork - eco-friendly and stylish

This is a fairly popular destination, which is limited only by the fact that this option can be very expensive. This state of affairs is explained by the fact that cork is a completely natural material.

Cork trim will create warmth and comfort and will not harm your health

For work, it is advisable to use roll options. They are great for self-fulfillment all works. It is important to consider that before you decorate the arch located next to the kitchen, cork material, it needs to be waxed. This will prevent damage to the coating.

Of course, finishing the arches in the apartment with a cork is a great solution, but you need to remember that it must be kept overall design interior.

It must be taken into account that all Finishing work must be carried out in strict observance of the existing rules. Then such an architectural element will become a real decoration.

Finishing options for arched openings (20 photos)