Ideas and advice from designers for the creation and design of stretch ceilings in the bathroom and toilet. What is the best ceiling to do in the toilet: a guide to options Suspended ceiling structure

Plastic panels today on construction market are becoming more and more popular. This is no coincidence, because if you install such material in a toilet or bathroom, then the room will look aesthetically pleasing and neat. The panels are easy to care for, they weigh a little. Take a closer look at this finishing option when renovating your bathroom or toilet. The panel is attached to the frame with a stapler or self-tapping screws. Spotlights are built into the ceiling made of this material.

Pros of PVC

Plastic ceiling is the most the right decision as it has advantages over other materials:

not afraid of moisture;
withstands temperature drops in the room;
does not absorb moisture;
does not swell under the influence of moisture;
does not increase in size at elevated temperatures;
hygienic, does not allow the development of mold and mildew;
thanks to the excellent reflectivity of the panels, the toilet becomes lighter, and because of this, the consumption of electrical energy is saved;
electric wires are removed under the panels, which go to the lighting fixtures;
the surface of the walls and ceiling becomes even.

The plastic panel is a long strip with an average width of 25–30 cm. The end is cut off, and there are locks on the sides, which will connect the elements during installation.

In the photo - PVC cross-section. There are stiffeners inside. So lightweight material but durable at the same time.

Panel profiles

This material is for decorative design when cladding ceilings or walls in a toilet or in another room with PVC panels. It is divided into the following types.

Start profile. Covers the trimmed ends of the panel. Fastened around the perimeter of the room.

The F1 profile covers the cut end by outer corner when you want to go to another plane. It is used in the event that one of the walls is sheathed, but the one that is around the corner is not.
Profile H (connecting). Serves to lengthen the strip if it is not enough.

External and inner corner designed to cover the ends in the corresponding corners.
The ceiling plinth has the same structure as the starter profile, but with a more attractive look.

Pros and cons of PVC panel mounting

Each of the materials intended for cladding has its own advantages over others. PVC panel also has many positive properties:

evens out the curvature of walls and ceilings in rooms, without the need to dismantle old coatings;
installation is quick and easy;
heat and sound insulation is laid behind the panels;
no dust and no "wet" process;
affordable price.

Disadvantages of plastic:

it will not be possible to complete a multi-level ceiling;
some panels look "cheap";
the connection between the panels is visible.

Therefore, when planning repairs in a toilet or bathroom, it is advisable to take a closer look at the quality of the material. After all, the better it is, the more expensive it is, and, accordingly, appearance more attractive. For this reason PVC panel limited in use. It happens that when installing a lighting fixture, the plastic ceiling shines through.

Important! Before you buy plastic material, weigh all the pros and cons so you don't regret it later.

Calculation of material for installation

First, calculate the area of the ceiling in the toilet. Then divide the resulting figure by the total area of one PVC panel. Add 15% to the resulting number for trimming and round to the nearest whole number.

To calculate the amount of metal profile, follow the diagram of the ceiling in the toilet, observing the scale. Determine where the parallel lines will go along the ceiling. They are necessary for fixing the profile. The interval between parallel stripes is at least 50 centimeters. Based on such calculations, it is easy to calculate the required amount of material.

For fixing along the perimeter of the surface, you need to purchase the UD strip, and for the guides - CD. To attach PVC strips to the profile, you will need self-tapping screws with wide caps.

To complete the work on finishing the ceiling will help plastic skirting board... To calculate its amount, measure the perimeter of the ceiling, divide this number by three, and then round it up.

Installation of a frame for PVC panels

The installation of the frame in the toilet is carried out using the aforementioned profiles: CD and UD. Use and wooden slats, but much less often, because wood is exposed to moisture, especially in a room such as a bathroom or toilet. The tree is prone to decay and will last less.

How to install the frame correctly?

Marking is carried out using a level. V large room it is better to use a long level, and in a small toilet a simple rack and pinion tool will suffice. Marks are made for the guide profile. Location depends on them hanging panels PVC on the ceiling.
The profile, if necessary, is cut according to the size of the room (the length of the profile is 3 meters). It is drilled in 50-60 centimeters increments. After that, the guide profile is applied to the wall, the holes are marked on it, the dowels are drilled and inserted. Each time, check the horizontal level.
The stiffness of the frame gives ceiling profile... The mount for it is chosen, taking into account the distance to the base: if the gap is insignificant, then a U-shaped suspension can be used. If it is large, then it is better to take quick-gimbals with knitting needles. Sometimes specialists make special “boots” for the UD frame. To do this, cut the metal with the letter "G" and attach it with the smaller side to the ceiling, and the larger side to the bearing profile.
The hangers are fastened to screws, checking by level. The step between the profiles is 50 centimeters, they are placed perpendicular to the PVC panels.

Definition of quality

When purchasing, inspect the panels carefully. Quality products even, the pattern is evenly distributed. The front side is smooth and flat. Distortion and curvature of lines are not allowed.

Important! Count the number of stiffeners inside the panel. The more there are, the stronger the structure.

The thickness of the stiffeners and the outer walls of the plastic plays a role. Take two strips and try to connect them. The main thing is not the quality of the connection, but the ease of docking. There shouldn't be any between the stripes large gap... To determine the strength of the material, take the strip and squeeze it hard, then inspect the surface. If it is not deformed and cracked, it is quality material... But slight deformation is acceptable.

Check the strip for bending. To do this, bend and unbend it 3-4 times. If after this procedure the material has survived, then you can work with it. Poor quality plastic will deteriorate during installation.

What is required to work with plastic?

Plays an important role color scheme... Today this is not a problem, and everyone will find for themselves interesting option.

Toilet cladding is impossible without source material and tools. You will need the following:

Sharp knife to reduce size plastic strips. Kitchen knife will ruin the material and cut unevenly.
Self-tapping screws for fastening strips.
Wooden beams for the frame with a cross section of 3 x 10 cm or metal parts described above.
If you are planning to fix the panels directly to the wall, you will need liquid nails or polyurethane foam.
Any renovation will not be complete without a tape measure.
Building level for mounting the frame.
Decorative skirting board, which is attached to the wall.
Profile corners.

Mount selection

Before starting work, determine how you are going to fix the panels: polyurethane foam or using a wireframe.

The first option involves the purchase of foam cylinders. When purchasing a product, pay attention to the expiration date. Fresh foam will have more yield. If the toilet is spacious and there is brick walls, it is not necessary to mount the frame. It is allowed to fix PVC panels with liquid nails glue. This job is not difficult, but it takes patience.

How to cut plastic material?

This process is straightforward. Take the stripes and lay them on the base with the wrong side. Then an incision is made with a sharp knife to form a line. They break the plastic along it and again cut it off completely along the marked line with a knife.

Preparation for work

Repair of the toilet and preparation for cladding begins with cleaning: the sockets are removed from the walls, lighting, hoses, pipes.

If selected frame method fastenings, it is more rational to use galvanized parts. If you took a wooden block, treat it with an antiseptic.

First, the frame is mounted, and then the strips are installed, where the panels are inserted. Ceiling work in the toilet starts from the corner. One edge of the PVC strip is inserted into the profile, and then the other side is attached to the screws

The next strip is easier to insert, push it until it clicks. And again, the other side is attached with self-tapping screws. Then the plinth is installed and decorative overlays... With their help, you can disguise defects and technological gaps. They are attached with glue, as these are purely decorative details.

Almost everyone will be able to repair a toilet using PVC panels. The process is shown in detail in the video:

A toilet takes up a small area in a house or apartment. Despite this, he, like any room, needs repair. Consider how to make a ceiling in a toilet using modern building materials... And also we will get acquainted with their advantages and disadvantages.

Ceiling features

If you do not want to repair the ceiling in the toilet and bathroom too often, you need to pay attention to the features of these rooms:

condensation may collect, which may cause mold in the corners;
pipes may leak, and then they will need to be replaced immediately;
hanging structure can visually reduce the space;
incorrectly selected material and finishing method can spoil the look as a whole.

Therefore, it is necessary to take all this into account and opt for the method in which you will have free access to the pipes, the height will decrease to a minimum, and condensate will not collect. And also, importantly, the ceiling surface will be combined with the floor and walls.

Advantages and disadvantages of finishing

Toilet and bathroom ceilings can be repaired in several ways.

Stretch ceiling

The stretch ceiling in the bathroom and toilet will look aesthetically pleasing and beautiful if you maintain glossy surface... To do this, you must regularly wipe it without damaging soft material.

The advantages of such ceiling system should include:

perfectly flat surface;
hygienic material;
the ability not to attract dust;
resistance to high temperatures;
moisture resistance.

It is not difficult to make a stretch ceiling in a toilet. This does not require alignment base surface... It is necessary to mount the frame, carefully pull and secure the canvas.

Flaws:

you can easily damage the material itself;
stretching work is difficult for one person to do;
the area of the room is noticeably reduced.

Suspended structure

More practical option is a suspended ceiling for a toilet. Thanks to its installation, it is possible to provide high sound and heat insulation.

This design allows you to install spot lighting... For its installation, you can apply various Construction Materials: drywall sheets, plastic panels, sets of slatted ceilings for bathrooms and toilets.

Plastic ceiling

The ceiling made of plastic panels in the toilet has a number of advantages:

low cost;
moisture resistance, which is important for their installation in these premises;
ease of maintenance;
impact resistance and durability;
replacement is acceptable individual elements;
resistance to temperature changes;
resistance to the use of various household chemicals;
big choice colors.

When choosing this material, you should also be aware of the shortcomings:

not fireproof - in case of fire, it can emit corrosive smoke harmful to humans;
Severe pinpoint impacts may damage the individual panel and require replacement.

The slatted ceiling in the toilet is a separate group suspended structures, which is recruited from special aluminum elements.

The advantages of this material:

durability - thanks to high quality sheet steel;
moisture resistance - does not deteriorate in contact with water, thanks to a special coating with polymer or zinc, perfectly withstands temperature extremes.
A wide range of colors of slats makes it possible to combine different shades.
Due to its properties, it is suitable for finishing the ceiling in toilet and bathroom.

The disadvantages include:

Plasterboard ceiling

This surface has a number of advantages:

hides irregularities and roughness;
after installation, allows for finishing various materials;
durability of drywall sheets;
withstands temperature extremes.

The disadvantage of this design is that the distance between the ceiling and the floor is reduced. And also, if you decide to repair the ceiling in the toilet with your own hands, you will need outside help... Since it will be better when fastening if someone will support the drywall.

Mirrored ceiling

The mirrored suspended ceiling in the toilet allows you to visually enlarge the room.

There are many advantages to using mirrored panels:

perfect combination with others decorative elements;
high functionality;
visual magnification space;
made of moisture resistant materials - plastic, glass or metal.
sound insulation and practicality;
ease of care - can be wiped with a dry cloth or with a glass cleaner.

The surface on which the mirror panels will be laid must be absolutely flat.

Such ceilings will perfectly fit into any interior.

To determine which ceiling is best done in the toilet, it is very important to consider specifications and the features of this room.

Color selection

The choice of the color of the ceiling in the toilet will depend on two factors - the decoration of the walls and the height of the room.

Low room

In this case, the ceiling should be lighter than the walls. Any pastel shades... For example, light blue or light pink. You can also visually "expand" the space using mirrored panels. Slatted panels in silver, gold or chrome are suitable.

Light pink stretch ceiling with built-in lights

Room with high ceilings

To bring the ceiling closer, you can use dark tones - red, purple, blue. In this case, the wall decoration should be lighter.

You should not make a ceiling in the toilet at home artistic painting or photo printing. This option is suitable for public places.

How best to make the ceiling in the toilet or bathroom is up to you. The main thing is to choose high-quality moisture-resistant materials and then they will last longer.

The toilet is a specific place in all respects, and in terms of use, and in size, and in the environment. Often, when carrying out repairs in the house, sufficient attention is not paid to this room. But it is worthwhile to understand that if you undertook to decorate a house, then you need to do this completely, nothing can be an exception. Moreover, the toilet is a small room, so repairs, including finishing the ceiling, will not require much time and money.

The features of this room and the design options for its ceiling are described below. The most popular finishes are provided with step-by-step instructions.

Toilet ceiling requirements

home distinctive feature toilet - the presence of sewer and water pipes, the toilet itself, which is obvious. Also sometimes hot and cold switches are located there. cold water, counters and, if it comes about a private house, a heating boiler. In this regard, the following requirements are imposed on the decoration of the toilet, including the ceiling.

Another feature of the toilet is its extremely small footprint. For this reason, there are specific requirements for the ceiling finish.

The next question to be considered is what colors and in what situations are used for the ceiling decoration of the toilet.

Color

Before choosing the color scheme for finishing the toilet, determine the area of the room and how the height of the ceilings relates to the length and width.

If the room has a sufficient area and the ceilings seem to be relatively low, then they need to be visually "raised". For this, light shades of blue, pink, green and beige are used. Suitable for this and the classic White color... Silver or light metallic shades will help enhance the effect. An alternative option for visually "raising" ceilings can be a mirror finish using panels or PVC stretch fabric.

Prices for plastic ceiling panels

plastic ceiling panels

Black stretch ceiling - not the best way for toilet

And in a situation where the length and width of the toilet are very small and even the standard 2.5 meters seem extremely high for ceilings, use light colors undesirable - the room will become uncomfortable, you, your household and guests will feel here like in a well. Therefore, use in moderation dark colors- blue, purple, dark gray. In some situations, golden is acceptable.

Important! The location of the lamps in the toilet should be chosen based on the same considerations - if the ceiling seems low, then place the lamps at the top. In the opposite situation, the luminaires are placed on the walls.

Another finishing rule to remember is to avoid the uniformity of the walls and ceiling, the result will be a very uncomfortable room, more like a prison cell.

Whitewash

Let's start from the very simple option finishes - whitewash. The main advantage of this option is its low cost, simplicity and speed of work. So, you can whitewash the ceiling in less than 30-60 minutes.

But similar advantages turn into disadvantages. When using whitewash, you can forget about moisture resistance - the coating gets wet and swells slightly. A old finish even peels off from contact with water. But in this case, the problem can be identified immediately and action can be taken. And again - not a problem.

Before starting work, the concrete floor must be prepared. Since the area of the room is small, the process does not require much time and effort.

Step 1. It is determined using the level of the difference in the height of the ceiling in the toilet.

Step 2. In a bucket, using a drill or a perforator with a mixer attachment, the putty solution is kneaded.

Whitewash prices

Types of Knauf putties

Step 3. Cracks and defects in the ceiling are repaired with a small spatula.

Step 4. The solution is applied to the entire surface of the ceiling with a sufficiently thick layer and leveled.

Step 5. The applied putty should dry within 24 hours.

Step 6. The next day, it is sanded with an emery cloth. Grouting should be done in undulating movements.

Important! For the toilet use lime wash... The chalk-based composition will not last long enough.

The prepared solution is poured into a paint tray, also called a ditch, and applied with a roller to the ceiling surface. Make sure that the whitewash is applied evenly. The layers applied with a roller are overlapped by 5-15 centimeters so that there are no untreated areas left.

If the whitewash has partially crumbled over time or the finishing layer has been broken by contact with water, then the coating can be renewed, since this does not require a lot of time.

Putty prices

putty

Dye

This finish has similar advantages to whitewashing - the relative cheapness, speed and ease of work. In addition, the paint has a variety of colors, which will make the ceiling in the toilet beautiful. For finishing, choose waterproof grades - oil, acrylic, latex or silicone compounds. Some types will also work. water-based paints, but be careful when choosing - only waterproof compounds.

Table. Popular paint brands suitable for toilet ceilings.

Name	Manufacturer	A type	Peculiarities	Consumption - m2 per one liter of paint
SNIEZKA KUCHNIA-LAZIENKA	SNIEZKA	Water-based	Includes antiseptic, moisture resistant, biostatic	12
Effekt Facade Silikontop	Effekt	Water-dispersive with the addition of silicone	Water repellent	5
TICIANA Т100601А	TICIANA	Acrylic	Light and water resistant, includes an antiseptic	10

The application process is the same as for whitewashing.

Concrete slab putty in the toilet. detailed instructions is presented above, in the section on whitewashing.
The paint is unpacked and poured into a paint bath.
The first layer is applied with a roller. There should be an overlap of 50-100 millimeters between the stripes.
Two or three more layers are applied in the same way. Make sure there are no unpainted areas. Brushes should be used at the junctions of sewer and water pipes to the ceiling.

Important! When working with some types of paints, for example, with oil paints, use a respirator mask - prolonged inhalation of vapors leads to feeling unwell and headaches.

Another option for finishing the ceiling in the toilet is different kinds tiles. Their overall advantage consists in the fact that an attractive outer coating is created that eliminates small differences in height and unevenness of the concrete floor, but, unlike suspended and tensile structures The tiles do not make the ceilings in the room lower.

Ceiling paint prices

ceiling paint

When choosing such a finish, attention should be paid not only to the quality of the material, its color and texture, but also to the size. Small tiles will create an effect that visually expands the length and width of the toilet.

The following types of tiles are used as finishes:

foam;
polyvinyl chloride;
cork.

Foam ceiling tiles stand out for their extremely low price - only whitewashing can be cheaper. It is not difficult to glue the tiles to the ceiling, but at the same time they change color over time. In addition, during the installation process, be very careful not to break the thin and fragile foam panels.

The process is as follows.

Step 1. The concrete floor is covered with a deep penetration primer - this improves adhesion to the adhesive, and the tiles hold better and longer. Allow the primer to dry.

Step 4. Glue is applied to the foam panel - a few drops in the center and a strip along the perimeter of the tile.

Step 5. The tile is applied to the ceiling, slightly pressed (but not too hard, so as not to damage the material), after which you need to wait a while for the adhesion to establish.

Step 6. Until the glue has set, the tile is carefully leveled. Remains of glue are removed with a narrow spatula.

Step 7. The previous steps are repeated and the rest of the tiles are laid in the same way. Joint gaps should be kept to a minimum. In the future, they can be treated with silicone sealant.

Advice! The finish can be complemented with a skirting board.

PVC tiles are more expensive than foam tiles, but they are more durable. In addition, this finish is waterproof. When buying PVC tiles, carefully monitor their quality - made in violation technological process the finish will deform or fall off over time. The installation process is the same as for foam tiles.

Another alternative to foam tiles is balsa wood... But they have their own characteristics. First, the color of the panels is not suitable for toilets with low ceilings. Secondly, their cost is significantly higher than that of analogues made of polyvinyl chloride or expanded polystyrene. But in addition to its attractive appearance, cork tiles have sound insulating properties.

Plastic panels

We now turn to the description of finishing for the ceiling in the toilet using suspended structures. They completely hide all the imperfections and irregularities of concrete or wooden floor, but at the same time they hide from 30 to 50 millimeters or more from the height of the ceiling. Therefore, they should not be used in rooms with very low ceilings.

Let's start with plastic panels. This is an affordable and very diverse finishing material with the following advantages.

Ease of maintenance - dust, dirt and condensation accumulated on the ceiling can be easily washed off with a cloth or a sponge soaked in soapy water.
Ease of installation - the process is available even to those who are not qualified specialists and do not have extensive experience in repair work.
Variety - There are many types of plastic panels. Some are stylized as wooden lining, there are also panels with a mirrored surface or with a surface imitating stone. Here you will definitely find the option that is right for you.
Moisture resistance - plastic is not afraid of condensation. And when competent installation the sturdy suspension structure will be airtight enough to withstand a small flood from neighbors.
Heat and sound insulation. The plastic itself and air gap between it and the overlap serves as a barrier in the way of sounds from above or warm air going up.

As for the disadvantages of plastic panels, such products can be damaged when struck by sharp objects, and when they burn, they emit smoke containing harmful substances.

Now let's look at how to mount such a structure.

Step 1. The surface is prepared - the old finish is removed from it, if any, seams and cracks in the floor are closed.

Step 2. A crate is installed on which the panels will be directly mounted. She gets settled from timber with a cross section of 3 by 3 centimeters. The interval between the elements of the frame is from 30 centimeters to half a meter. Fastening to the floor is done with self-tapping screws with dowels.

Step 3. If you plan to install lamps, wiring is laid and fasteners are installed under the lamp. A hole is made in the panel, which should be located in this place, with a drill with a crown attachment exactly according to the diameter of the future lamp.

Drywall prices

drywall

Making a hole for a lamp

Step 4. The start, finish and side profiles are installed.

Step 5. The first panel is inserted into the side profile, moves to the starting one and is fixed there on the crate with the help of small screws screwed into the bar adjacent to the bars. The outer surface of the panel must not be drilled or damaged in any other way.

Cutting PVC panel 5 mm shorter

Installing the first panel, step 1

Installing the first panel, step 2

Step 6. Similarly, the next panel is wound up and carefully mates with the first tongue-and-groove connection. The operation is repeated with the fasteners.

Step 7. The rest of the panels are laid in the above way.

Step 8. The finish panel is trimmed so that it can be inserted into the profiles. This completes the process of laying the plastic panels.

Installation last panel, step 1

Installing the last panel, step 2

In a similar way, a ceiling made of natural lining or panel-cassettes is installed, the structure of the lathing can only differ.

Stretch ceiling and plasterboard ceiling

The remaining options for suspended structures are a plasterboard ceiling and a stretch canvas. But using them for the toilet is a matter of personal preference, and very controversial. This finish is perfect for large rooms, but in small rooms, multi-level structures may not look entirely appropriate.

Another controversial issue of such ceilings is access to communications. To repair or replace the sewer and water pipes in the toilet, partial or complete dismantling of the suspended structures will be required.

If you decide to use one of these designs, then remember the following nuances.

Choose only moisture resistant drywall grades. Other options for constant contact with condensation will quickly become unusable.
The profile for suspended structures must be galvanized - without protection against corrosion, it will lose its strength over several years and at one "fine" moment the entire ceiling may simply collapse.
A stretch ceiling with a PVC sheet is extremely convenient when flooding from above - PVC can withstand up to 80-100 liters of water per square meter.
Use baguettes and canvas with harpoon fasteners - this way, dismantling during pipe repairs will be carried out as quickly as possible and without damage.

It makes sense to use a gypsum plasterboard or stretch ceiling in a newly built building, especially made of wood, since such structures (we are talking about ceilings), in the overwhelming majority of cases, do not deform and do not lose their attractiveness during shrinkage.

Stretch ceiling prices

stretch ceiling

Finally, it is worth saying that regardless of the chosen option for the ceiling finish, before performing it, decide the issue with waterproofing - several layers special film on good fasteners will significantly reduce damage in case of possible leakage from above.

Video - False ceiling in the toilet. Part 1

Video - False ceiling in the toilet. Part 2

Video - False ceiling in the toilet. Part 3

Video - False ceiling in the toilet. Part 4

Video - False ceiling in the toilet. Part 5

August 1, 2016
Specialization: Master in Internal and exterior decoration(plaster, putty, tile, drywall, lining, laminate, and so on). In addition, plumbing, heating, electrical, conventional cladding and balcony extensions. That is, repairs in an apartment or house were done on a turnkey basis with all necessary types works.

For renovation, you can choose 4 finishes, these are plasterboard, plastic, slatted ceiling and stretch ceiling in the toilet. Of course, there is also an option for a conventional plastered ceiling, but this no longer belongs to the category of suspended structures. Let's take a look at each of these designs now, and you will also have the opportunity to watch the video in this article.

Dropped ceilings

First, let's look at the principle of suspended ceilings as such:

any suspended ceiling - created with your own hands, implies the presence of a frame for installing the cladding;
this means that you definitely need to hit the horizontal level, on which both the frame and the cladding will be mounted;
the crate here can be ambiguous, that is, it can be CD profiles, slats, or a profile for stretch ceilings(wall, ceiling, harpoon and so on);
the essence of the installation of each of the frames is as follows - not only the cladding should be installed there, but also built-in lighting devices. At a minimum, such a cartridge has 70 mm, therefore, this figure should proceed as the minimum depth, although, most often, it is 100 mm;
to mark the level horizontally, as a rule, use a water or laser level , although, personal experience pulls the balance to the side of the water device;

please look at the diagram above - you can see here the principle of installing the battens under any type of suspended ceiling. That is, the plane should be ideal, without any drops, for which nylon threads are used (in the diagram they are indicated in blue);
do not disregard the draft base- it must be rigid so that the frame holds well.

I will not scrupulously describe the installation of each cladding - usually, this comes with practice. But, nevertheless, it is important to understand the principle of each of them, so that you can make such repairs yourself.

PVC panels or wood lining: 1 way

Let's briefly figure out how to make plastic, MDF or wooden ceiling v small room toilet. First of all, this is the installation of the battens, which can be either CD profiles or wooden slats (there is essentially no difference as such).

The main difference here is only in the mount. If the plastic is fixed with a stapler through the edge of the panel, then MDF and wood are fixed with steel clips.

In addition, the panels can be fixed with self-tapping screws - I personally prefer this option - screws are always more reliable than metal brackets. In addition, studs are sold with clamps, but it is better not to use them - fix this bracket with a self-tapping screw in the central hole.

Make the last lining 5 mm of the required distance - this is the width of the chamfer and it will be much easier for you to insert it.

Rack ceilings: option 2

The installation of a slatted ceiling is very similar to the installation of lining, only here there is a significant difference in the profiles. A U-shaped profile is installed along the perimeter, as usual, but now, the intermediate traverses are a device with latches (see the photo above). Here, a separately taken panel is simply fixed - it is simply snapped into place.

In most cases, the strips are installed with gaps, where inserts are later installed in the form of strips of a different color. The rails themselves can be plastic or metal (aluminum), which determines their price. The holes for the luminaires are best cut before installing the panel on the batten, but for this it is important to make the correct markings.

Plasterboard ceilings: method 3

But drywall sheets, in my opinion, are the easiest to install - they are large, 1200 × 2500 mm, and the toilet is in high-rise buildings (with separate bathroom) is not wider than 800 mm, and in lengths 1200-1300 mm (it happens in different ways). In fact. Half a sheet of ceiling drywall will be enough for you - it is 6-8 mm thick (depending on the manufacturer - it is thinner in China).

Here, too, you can use both CD profiles and wooden slats, although my experience suggests that metal is still better. GKL is fastened with self-tapping screws 25 mm in 30 cm increments, but you can also make such a ceiling from pieces - in any case, you will have to putty it. The most important thing here is that each screw is recessed by 0.5-1.0 mm - this will help with plastering - the head will not interfere.

Stretch ceilings: 4 way

In total, there are three types of baguette for stretching PVC cloth - cam, wedge and harpoon. In fact, they are all the same from a technological point of view - just from the technical point of view, the installation of the canvas is somewhat different. The film is stretched by heating the polyvinyl chloride with a gas or electric gun.

I want to note that the installation of ceilings from PVC is better entrust everything to specialists so that you do not spoil an expensive product. However. If you wish, you can do such things yourself.

Conclusion

It's hard for me to say which is the best ceiling for your toilet - here it is important just to focus on the wall decoration and your own taste. But if you have any specific suggestions, then write them down, please, in the form of a post in the comments.

August 1, 2016

If you want to express gratitude, add clarification or objection, ask the author something - add a comment or say thank you!

Repairs in living rooms can be carried out at least every year: change the wallpaper, repaint the walls, renew the floor, and so on. Bathroom makeover and toilet room happens much less frequently. As a rule, a bathroom renovation is undertaken at least once every ten years. After all, the cost of materials in this case is greater, as well as work in this room. Therefore, the choice of materials for finishing the bathroom should be approached responsibly so that you do not have to make repairs again and spend money again. We invite you to find out what is in the toilet and bathroom.

Requirements for the ceiling in the bathroom

A toilet, even if it is not combined with a bathroom, is a place with high humidity... Therefore, not all materials are suitable for wall and ceiling decoration. When choosing a coating, you must be guided by the following criteria:

The moisture resistance of the material must be very high.
The color of the ceiling decoration in the toilet is chosen in light shades in order to visually enlarge an already small room.
The type of material depends on the height of the ceiling. It decreases if special structures are used (for example, with suspended and stretch ceilings).
The material must have a long service life.
Undesirable elements such as mold, smudges, streaks, condensation, etc. should not appear on the ceiling.
There must be a possibility for the installation of built-in elements (for example, hoods, lamps, etc.).
Hidden items must be accessible, if provided.
Reasonable price for the material itself and related products.

Based on the above requirements, there are the most acceptable options for finishing the ceiling in the toilet.

Types of materials for the ceiling in the toilet and bathroom

Today, there are a fairly large number of options for finishing bathrooms. When comparing price and quality, the following types of ceilings can be distinguished, which are popular:

tension;
rack and pinion;
plastic;
colored;
tiled;
plasterboard;
finished with vinyl wallpaper.

Each of these options has a different price range, and also has its own pros and cons.

Vinyl wallpaper ceilings

Vinyl wallpaper is relatively inexpensive material, which is suitable for finishing walls and ceilings in the bathroom. Thanks to the technology by which they are produced, such a finish copes with all the requirements inherent in a toilet room.

Pros of vinyl wallpaper:

affordable price;
outer synthetic film that is not afraid of water and moisture;
can be changed often, and without special efforts.

Disadvantages of vinyl wallpaper:

a carefully prepared surface is required to aesthetic appearance premises;
the presence of joints can provoke the development of a fungus;
short-lived, require frequent replacement.

Painted ceiling

The ceiling in the toilet (see photo example above) can only be painted with a special acrylic paint on the water based designed for bathrooms. It dries quickly, does not have a bright unpleasant odor, not afraid of water and moisture, also protects against mildew and mildew. And there is also a rich palette, thanks to which you can bring to life even the most daring design ideas. Another indisputable advantage of the paint is its price. Therefore, painting refers to budget options repair.

The disadvantages of a painted ceiling include the need careful preparation surface that must be perfectly flat. Unless, of course, you want to have a nice washroom.

Plastic ceiling

This type of finish will cost a little more than the previous two, but will last much longer. in the toilet, it is a frame made of metal profiles on which plastic sheets are attached. They are available in various sizes, colors and surface types (glossy or matt).

Advantages of a plastic ceiling:

budget price;
hides ceiling communications (hoods, wires and pipes);
has excellent moisture resistance;
does not provoke the appearance of mold and mildew;
the panels are easily removed separately;
has a long service life.

Disadvantages of a plastic ceiling:

underestimates the height of the ceiling due to the peculiarities of the fastening;
can only be installed by the master;
it is necessary to select recessed luminaires.

Plasterboard ceiling

The ceiling in the toilet and bathroom, made of plasterboard, is usually used in cases where it is much cheaper to sew a surface than to bring it to its proper form. Finished construction plasterboard is putty and painted with water-based acrylic paint.

The disadvantages of this option are that it is necessary to hire qualified people, the height is "eaten up", there is no possibility of quick access to hidden objects (for example, the wiring of built-in lamps). Merits plasterboard ceilings is the implementation of various design ideas(for example, two-tier designs). Also, such a surface turns out to be perfectly flat, which is impossible in other versions (except for tension).

Stretch ceiling

The stretch ceiling in the toilet helps to visually enlarge a small space thanks to its glossy surface. It also allows you to hide all the flaws. The ceiling is perfectly flat and airy in appearance.

Advantages of a stretch ceiling for a toilet:

long period of operation in the absence of emergencies (flood);
high moisture resistance;
elimination of the situation of the appearance of mold and mildew;
you can make the effect of "starry sky", when a lot of small luminous points appear on the ceiling, arranged in a chaotic manner and resembling stars;
wide color palette, options with a pattern and without.

Disadvantages of stretch ceilings in the bathroom:

high cost of materials;
the need to hire highly qualified specialists;
inaccessibility of easy access to hidden objects and pipes.

Rack ceilings in bathrooms

A slatted ceiling in a toilet is made of a material such as aluminum or steel. It is relative new variant decoration, which was previously most often used in public areas. The slatted ceiling has a fairly wide range of colors, which includes about 50 shades (for example, chrome, gold, mirror surface).

The service life of this finishing option is quite long - about 15-20 years. Rack ceilings absolutely non-flammable and environmentally friendly. Reiki does not absorb moisture and does not rust. It is worth noting the fact that such a ceiling can be given absolutely any shape. And also, as in the case of the tension and drywall option, you can hide all surface imperfections. True, the ceiling height decreases in the same way - by about three centimeters.

For installation rack structures it is necessary to hire specialists who already know how to do this.

Tiled ceiling

Ceiling tiles are one of the simplest and most affordable in the toilet. This material has a wide selection of sizes, textures, color palette and drawings. Its main advantage, in addition to the price, is that it can be glued even to an imperfect ceiling. The tiles are able to cover all the imperfections (except for large drops) of the surface and will help to visually level it.

The installation of the material does not require much effort, it can be done independently. Changing it is also quite easy. Ceiling tiles moisture resistant, they are not affected by fungus and mold. They are also paintable if you are tired of the old design and don't want to change the finish. It is worth noting the fact that together with additional accessories (for example, special friezes) you can make a very interesting design premises.

Remember that the ceiling in the toilet and bathroom should not only serve, be moisture resistant and protect against mildew and mildew. He also plays a significant role in interior design. With its help, you can not only hide flaws, emphasize the advantages of a room, but also make it unusual. Therefore, choose not only a high-quality and affordable option, but also one that will make the bathroom cozy. Also, do not forget that, regardless of the type finishing material, the ceiling must be primed to further protect the surface from moisture, mildew and mildew. It will also help increase the duration of the finish and save you from unforeseen costs.