A simple do-it-yourself country shower. How to quickly make a summer shower in the country with the help of improvised materials? Is it possible to buy a summer shower for a summer residence inexpensively: prices for finished structures

If it is not possible to conduct hot water in private house or in country house, then in this case it would be advisable to build an outdoor shower.

How to build a summer shower with your own hands from wood?

To build wooden shower in the country with your own hands, you can follow the following instructions:

First you need to choose appropriate place for building a building. When choosing, it should be taken into account that such country shower will be constantly exposed to moisture both inside and outside.

Tip: it is better to build such a structure in a well-ventilated area. This is necessary so that the wood dries faster. Also, do not plant bushes, trees and tall plants, as they retain moisture, do not allow air to circulate, and as a result, prevent the wood from which the country shower is made from drying out.

Production earthworks. For a shower, we dig a hole 1x1 m in size, 40 cm deep. We lay a layer of rubble on the bottom of the pit, which will help the soapy water soak into the soil faster. Next, cinder blocks should be laid out in the corners. They must be leveled.

Next, we proceed to frame manufacturing. To do this, we take boards whose thickness is 30 mm and a width of 15 cm. A base measuring 1x1 m will be made from them. 4 beams with a section of 70x100 mm are attached to this base. To bandage the frame, side and two transverse jumpers are used, which are inserted into the grooves. They also serve as a reinforcement for the roof, on which a hundred-liter tank will be installed.

Works on frame sheathing. For these purposes, you can use lining, blockhouse or false timber. The gaps between the grooves should be two to three millimeters. This is necessary so that the timber can expand freely when regularly wet. In our case, a material imitating logs was used for shower cladding.

do-it-yourself shower step-by-step instruction. Photo

Finishing work. Before painting, it is necessary to prime the wood. For these purposes, a bioprotective antifungal impregnation is suitable, after drying of which the surface is painted with a front acrylic water-borne varnish in at least 3 layers.

The next stage in the construction of a soul in the country is tank installation for water.

building a shower in the country. Photo

Tip: for a summer shower, it is advisable to use a tank with a minimum volume of one hundred liters.

You can build such a wooden shower in the country with your own hands in one or two days.

building a shower in the country with your own hands. Video

Do-it-yourself summer shower

For the construction, it is necessary to prepare the following materials:

• timber;
• fasteners (self-tapping screws);
• shower kit, which includes a bracket, a mixer, a curved pipe, an adapter and a nozzle;
• rubber hose.

How to build a summer shower in the country with your own hands?

Construction order:

Drafting drawings. For such a structure, it will be necessary to make wooden pallet in the form of a circle of dense wood. We will have cardboard as a template. required size. First you need to lay the cardboard on a flat surface and fix it with tape. Next, using measuring devices, draw a circle with two squares located inside. According to this template, the construction of a wooden floor will be carried out.

do-it-yourself summer shower drawings

Construction pallet. The floor will be three-layer. The order of the base for the floor is as follows:

Works on pipe installation. Connect all the elements that are in the shower set.

do-it-yourself summer shower step by step instructions. Video

do-it-yourself summer shower step by step instructions. Video instruction

Summer shower for giving from pipes and polycarbonate

This option attracts with its low cost, resistance of materials to the action of sunlight and moisture, as well as ease of processing.

The procedure for the construction of the foundation and floor

Before you start building a polycarbonate outdoor shower, you need to decide on its location. For such a structure, an inconspicuous place with a flat surface, away from wells and wells, is suitable.

Site preparation. To do this, we fill it with sand and ram it.

Drill or dig four holes into which posts for the foundation will be inserted.

Lay a layer at the bottom of the hole rubble 10-12 cm thick.

Install pipes made of plastic, used for laying sewers. We make them inside and out.

do-it-yourself summer shower step by step instructions. Photo

In the central part it is necessary to dig drainage pit and fill it with rubble.

We also cover the area around the blind area with rubble.

From a bar with a section of 100x150 mm we make base for the construction and attach it to the foundation posts. For these purposes, it is necessary to drill holes in the cement and insert plugs into them.

It is also necessary to fasten jumpers to the frame with self-tapping screws and reinforce the structure with steel corners. Between the pipe and the beam we lay waterproofing.

Tip: before installing the jumpers, you need to try on the pallet, as it will subsequently be installed between them. Therefore, if necessary, it will be necessary to adjust the frame to the dimensions of the pallet.

Next, you need to remove the floor height from the timber 50x50 along the entire perimeter and after that you can proceed to the device floor covering . The result should be a base with a built-in pallet.

The order of the construction of walls and roofs

Let's start building wooden frame soul. At this stage, it is necessary to provide a doorway. In our case, the height of the walls will be 2.5 meters.

summer shower made of polycarbonate step by step instructions. Photo

A solid one is attached to the rafters crate.

Making a layer waterproofing from roofing felt or bikrost.

From the sides we produce sheathing finished board.

For coverage roofing use soft tiles.

After that, we process all wooden frame wood stain two coats, and then varnish in two or three coats. For such a structure as a half-carbonate summer shower, about 7.5 liters of stain will be needed.

Frame cladding polycarbonate With outer side. For these purposes, it is recommended to use special thermal washers, for which it is necessary to cut holes on polycarbonate using a cutter.

Door made in the form of a wooden frame. Its height is two meters. To give rigidity, jumpers and jibs are used. Next, the door frame is painted, hung on hinges and lined with polycarbonate.

After that hang water heating ba k, faucets, curtains, hooks, rugs and other accessories.

At the bottom of the pallet it is necessary to bring the drain into drainage pipe , inserted 20-30 cm into the crushed stone base.

At the final stage we produce entrance improvement in the country shower. To do this, we dig a hole, fill the foundation with concrete and lay reinforcement in it. After the concrete has gained strength, we lay bricks on it, on which steps made of wood will be installed. You can decorate if you want. To do this, you need cement and stones.

Attach steps.

Do-it-yourself shower for giving

The first thing to do before starting construction is to decide on location summer soul. For such a structure, a well-lit, calm, slightly elevated place is suitable.

Tip: it is desirable that the shower is not located too close to the buildings and is built in the same style as them.

Stages of building a soul in the country

Drafting project. It is planned to build a shower consisting of two small spaces. Minimum size bathing compartments should be 100x100 cm, changing rooms - 60x100 cm. In our case, the optimal shower size is 200x150 cm.

At the chosen site mark out the rectangle dimensions 140x190 cm. We drive pipes in the corners. The foundation for the shower will be piled from two-meter asbestos-cement pipes, the diameter of which is 90-100 mm. They must be buried in dug holes to a depth of about 1.5 m. 20-30 cm should remain above the ground. After that, drainage and a drain system are arranged.

Summer shower project. Photo

To organize the flow of water is done waterproof layer. It can be made from a PVC film or roofing felt, which must be laid on an inclined surface. Alternatively, a reinforced concrete screed can be made.

Making the top and bottom strapping frame.

Plank floor covering.

Tip: In order for water to flow out of the shower cabin, it is recommended to install floorboards with gaps that are 10 mm wide.

The shower room should be separated from the dressing room by a high threshold and curtain.

Finishing work. Outside, the country shower is sheathed with clapboard or siding, moisture-resistant plywood, fiberboard, etc. Inside, for finishing, materials that are not afraid of moisture should also be used.

It is necessary to install a water tank on the roof, the water heater is installed indoors.

Hozblok with a do-it-yourself shower

The order of construction of the structure:

After you have chosen a suitable place for the construction of a shower, you can proceed to earthworks: dig out foundation pit, fill it with PGS and lay out point brick foundation.

After the foundation is ready, you can proceed to the device wooden frame designs. For these purposes, a beam is used.

For plating shower on the sides and back in this project, a board with a thickness of 10 mm was used. A window and door opening should be provided in front.

Device roof frame from wooden beam. In this project, window openings should be provided on the folding roof.

Corners should be lined with boards.

Can be used for roofing shingles.

The door is made from boards. Handles for doors and steps can also be sawn out of wood.

Everything wooden elements necessary paint paint or varnish.

Bench arrangement, installation shower tray, wall cladding with plastic, fastening hooks, etc.

Summer shower projects for a summer residence

Project No. 1

For the shower, you can also use not only a wooden frame, but also a metal one. This design can be installed directly on the ground. A curtain is used as a door in this project.

Project No. 2

The shower can be made from a corrugated metal sheet that can be bent into a semicircle. For this option, there is no need to install a water heater. It will be enough to connect to the water supply.

Project No. 3

Such a summer shower made of pipes is lined with white plastic on the outside, and brown on the inside. The shower cubicle can be erected on a paved concrete pad. For this option, you will need a water heater.

Project No. 4

As a floor in such a shower, you can use wood flooring. Inside the room is lined with blue plastic. Instead of a roof, a wooden lattice is used.

Project No. 5

The base of this shower is made of metal pipes. Brown corrugated board was used for wall cladding. The roof is also made of corrugated board. Light enters the shower room through the holes between the wall and the roof.

Project No. 6

For the manufacture of this shower, red polycarbonate was used. For this option, there is no need to install a tank on the roof. To use such a shower, you will need to connect it to the water supply.

Project No. 7

The frame of such a shower is made of metal pipes, painted in blue color. Plastic was used for wall cladding white color. A metal structure was made for the tank.

Example #8

Rustic shower. The frame is made from dry tree trunks. Branches are used for cladding. Logs are fixed on top of the structure, on which a water tank is installed.

Project No. 9

The frame for such a shower is made of metal elements. Floor and wall cladding - varnished wood. Such a summer shower does not have a door and a water tank.

In summer, along with beautiful sunny weather and bright colors from plants, we get the need to take a shower more often than usual. In addition to this, on fresh air Swimming under the streams of fresh water is a real pleasure, especially if you live in an apartment and went out into the countryside. On cold days, when the water is not heated enough from the sun, you can make a heated shower.

As always, the most ingenious is simple. In our case, making a summer shower with your own hands is very simple; nevertheless, there are many options for implementing the idea.

Summer shower options for giving

Let's start with materials. It is realistic to assemble the frame from any beams, whether it is a metal-profile pipe, or wooden beams. The walls can be from a wide range of materials, here are examples: sewn up with wood, profiled metal sheets. The best quality and price converge if the summer shower is made of polycarbonate, but you can even use opaque oilcloth or tarpaulin stretched over the frame.

OPTION #1

More expensive, but also more reliable, will be a brick or building block shower. The structure can be made combined and a toilet can be built nearby, as can be seen in the photo. Masonry can be lined with any material available for this.

OPTION #2

To assemble a shower from a profile pipe, welding is most often used, but if you do not have the opportunity to use it, then you can fasten the beams through holes and bolts. In order for the corners to become rigid, a “scarf” plate or a diagonal strip of metal is attached to them. Such frames look good covered with tarpaulin or oilcloth, as can be seen in the photo.

Also, corrugated board can be easily attached to the tighter metal base, which will add reliability to the structure in many moments.

OPTION #3

In construction hypermarkets, you can find a ready-made shower for outdoor conditions. But there is an opportunity to save money and make a summer shower with your own hands. The general concept has already been described above - the frame is made of corrugated pipe, and the casing is made of polycarbonate. Original examples look at the photos.

Such structures are designed to be used storage tank summer shower, heating will be carried out due to the flat shape of the container.

OPTION #4

Another interesting solution there will be a combination. For example, three walls can be made of rigid material, sewn up with wood or a sheet of metal or polycarbonate, and the fourth wall can be a screen of opaque film. Unfortunately, it will not work to immerse a water tank on such a design, and therefore water can be let in from a home water supply.

This can simplify the task of providing shower water and heating. Thus, with your own hands, you can make a shower with heated water from a home column or boiler.

OPTION #5

A shower similar to the previous one can be made by attaching it to the house, or rather to its wall. Cover the wall with a material that will not allow water to penetrate the wall and bring the pipe for the watering can to a height of about 230 centimeters. In this case, the frame is not needed at all, but if open version not satisfied, then you can make a screen or curtain that will move along a curved pipe. The floor can be laid out with tiles or other convenient material, having previously made a drain.

OPTION #6

If possible, you can lay out shower enclosures from natural stone. This solution fits perfectly into landscape design the entire area. In the variant in the photo, water is supplied from a domestic water supply, since the presence of a barrel can disrupt the aesthetics of the structure. The stone was laid out without mortar, because its flat shape allows the whole structure to stand securely.

OPTION #7

A budget option for a summer shower is the use of materials from tree branches. The frame can be made from thick and even branches, and the walls from bending vines or long branches.

This option is not only quite cheap, but also looks original. The water supply due to the fragility of the frame is carried out from the water supply.

Finished blocks and prices

Factory-made outdoor shower cabins have a lot of variety. First of all, they can be made in various colors, since the colors of polycarbonate and corrugated board may be different. Also, the lining can be made of synthetic fabrics, for example, from a film or tarpaulin. You will also find two configurations: with and without a locker room.

On average, the prices for cabins packed in an awning are 15 thousand rubles. The package includes a tank with a volume of 200 liters. If you want to have a locker room, then the amount will be about 18 thousand or more.

The same options, but with polycarbonate walls and a heated tank, will cost 20 and 25 thousand rubles, respectively.

Of course, these prices are approximate and you can find the exact figures in local hardware stores.

What do you need to build an outdoor shower with your own hands?

Earlier we already talked about the materials from which you can make a shower stall, the frame is best made from a professional pipe; sheathing has a wide range of materials to choose from: profile flooring, polycarbonate, awning and even oilcloth. When choosing a material, consider the tools that you have for installation.

Also consider the durability of materials. For example, polycarbonate will retain its properties longer than wood, but it does not respond well to high temperatures and harder to assemble.

Preparation plan

1. Drawing and plan. On average, a shower cabin on the street is made with dimensions of 1000 * 1000 * 2200 millimeters. Such dimensions allow, inside, to feel comfortable for the average person. At the request of the owner, the width and length can be more, but in no case less. Reducing the parameters will create difficulties in accepting the procedure. And this height is due to the fact that the part will take away the lunge of the watering can from the ceiling and the pallet.

In addition, the drawing will be useful if you decide to include a dressing room or other extensions in the building. Such a calculation will help to avoid additional costs and be fully prepared for construction.

1. The choice of material for the frame. It is recommended to use metal: corner or profile pipe. For the frame, you will need a corner 50 by 50 millimeters or a professional pipe 40 by 20 millimeters. Calculate the footage of the blanks based on the dimensions of the shower: height, perimeter and length. Also consider tank dimensions when designing frame dimensions. The structure must be strong enough to bear the weight of the full container. In addition, such material will last much longer than any tree. Maintenance is minimal - touch up in time to avoid rotting.

If the choice falls on a tree, then in order for it to fulfill its role for a long time, it must be treated with special moisture-resistant agents, and then with paint or varnish. The part of the tree that will be in the ground must be covered with bitumen or resin.

1. Cladding material. The list to choose from is very large, but the most practical and most popular are brick, corrugated board or polycarbonate. All of these types differ in the way they are assembled and how they need to be maintained: for brickwork: you will need a mortar, after which it would be useful to cover it with inside varnish; it will be enough to attach the corrugated board to the bolts, having previously drilled holes; polycarbonate is also bolted, but it will already need washers.
2. Water source. Equip your shower with a capacity that is sufficient for the use of all those living on the site. On average, 20-30 liters of water are required per person (fortunately, the choice in stores is huge). Since the weather can bring surprises, heating will not be superfluous. It is possible to equip your tank with electric heating using a heating element. If possible, run water supply from the house to the shower, this will allow the use of water heated by a boiler or gas water heater.
3. Roof. The important part, because while you are swimming, there will be a rather heavy load on top. In order not to be injured, the material must be rigid. As a roof, it is better to use slate or corrugated board. Polycarbonate under a large load will simply burst.
4. Drain. Drainage is best done about two meters from the structure. This will help prevent bad odors. Convenient parameters for the pit will be 500 millimeters in diameter and 1000-1500 deep. The walls and drainage are poured with concrete using formwork.
5. Tools and consumables. At a minimum, you will need: a hammer, a saw and a hacksaw, a grinder, a drill. For bonding metal frame welding is well suited, and for it you will need electrodes. You will also need to acquire nails, bolts, drills with a diameter corresponding to the bolts.

You will also need a watering can, a mixer, if supply is provided hot water, adapters, nozzles, pipes and hoses for water supply.

Sequence of operations

To assemble a shower cubicle, you must:

1. According to the drawing in the photo, we weld or assemble with bolts, parts of the frame. When assembling, take into account the loss in length.
2. We put the halves vertically and connect them using welding seams or the same bolts.
3. We pour the screed-concrete and control that the legs plunge 10-15 centimeters into the screed. Using the level, make sure that the structure becomes even. For a brick building, concrete and screed are poured. For draining, a plastic pipe is used, which must be placed in concrete during the pouring process.
4. After the concrete has hardened, proceed to the sheathing and installation of plumbing, accessories, as well as the final arrangement of the booth.

Upon completion of the assembly of the frame, it remains only to veneer it with the selected material. Consider the dimensions of the material based on the dimensions of the "skeleton". It is better to arrange a drain using a pallet or, at the stage of concrete formation, make a current by placing it there plastic pipe, which will lead to a sewer pit.

The source of water can be plastic tank on the roof of the cabin, as well as a pipe from a domestic water supply.

As you can see, with just a little involvement of imagination, you can build an outdoor shower by spending a minimum of money and getting a maximum of aesthetics and quality.

Owners summer cottages They try to bring water to the house and arrange basic amenities. You can build a summer shower in the country with your own hands, both temporary and capital - the type of future structure is selected depending on individual needs.

Before you build a shower in the country with your own hands, you need to correctly design, determine the location of the future building, and select materials. The room should be not cramped, as comfortable and convenient as possible for use.

Location selection

In order to ensure a quick drain of water, it is best to install the shower on a flat or slightly elevated area. You should not choose a site located in a strong lowland or in a pit.

To avoid stagnant water, choose the right place for building a summer shower

Optimal for a country shower would be an open area, well lit by the sun, which is located at some distance from other buildings. In this case, the barrel will naturally heat up under the sun, providing a supply of warm water. This condition can be neglected only if it is planned to build a shower with heated water.

At the same time, the site where construction will be carried out should not be too far from home - after water procedures, it is desirable to get out of the shower into a warm room as soon as possible.

Size calculation

When building a country shower, the following parameters are used as standard:

1. height - 200–300 cm;
2. length - 190 cm;
3. width - 140 cm.

An example of drawing up a drawing of a summer shower

The indicated dimensions are very convenient in that, taking into account the thickness of the walls, the building will ultimately come out with an area of ​​​​200x150 cm - this is a completely waste-free option when using boards standard sizes. As a result, 100x100 cm will be allocated for the shower stall, and 600x400 cm for the locker room.

Necessary tools and materials

You will need the following tools:

• roulette;
• corner;
• level;
• hammer.

In addition, you need to stock up on nails and a skein of twine. Separately, you need to purchase a tank, as well as pipes, a couple of taps and a shower divider. As a building material for the construction of the cabin, brick, iron or plastic sheets are suitable, wooden planks, for the construction of the frame - pipes.

Tools needed for building a shower in the country

For the foundation pouring and the erection of brickwork, a certain amount of cement, sand and concrete will be required, and for the final finish - insulation materials, paint, plaster, clothes hooks, shelves for bathroom accessories and other accessories.

Options for shower designs for summer cottages

The easiest option for giving - compact portable shower, which is suitable for a one-time acceptance of water procedures, has a standard volume of 20 liters and is designed to supply water for 10 minutes. The principle of operation is reduced to filling the reservoir with water and subsequent heating in the sun, after which the portable shower is mounted to a height of 2 meters and is ready for use.

Portable shower

An open shower also has a simple design, the installation process of which boils down to the following steps:

1. fastening to the wall of a branch of a water pipe;
2. connecting a pipe and a watering can with a hose;
3. fixing the watering can holder;
4. screen installation.

A common option for suburban area is the so-called change house with a shower, the design of which assumes the presence of a one-piece modular container or a frame-collapsible block.

Options for a stationary summer shower for a summer residence

The installation of this design is quite simple - the territory is marked, the upper ball of soil is removed and leveled, a cushion of sand and gravel is created, on top of which the boards are laid. On the soil prepared in this way, a block assembled on site or a ready-made structure is installed.

Of course, a stationary shower will become the most solid, but it will take more time and effort to build it.

Foundation preparation

It is much easier to build a frame structure than a capital building - depending on the type of structure chosen, the stages of preparing the site for construction will differ.

For a temporary structure, it is enough to simply remove 10-15 cm of the topsoil from the site to level it, and then fill it with sand.

For a country capital soul, a foundation will be required, the depth of which is determined by the materials used for its construction. For example, for a brick shower, a foundation will be quite enough, the depth of which will reach 30 cm.

Foundation for the construction of a capital summer shower

The foundation is laid in the following sequence:

• pegs are driven into the outer corners of the future soul;
• a cord is pulled around the perimeter;
• a place is being prepared for pipes (a log or a branch wrapped in roofing felt is laid);
• concrete mortar is poured.

Advice! The formwork equipment will allow extending the period of operation of the shower - it is recommended to raise the level of the entire foundation by 10 cm, raising it above the ground with the help of boards reinforced with stakes and spacers.

Drainage pit equipment

The volume of the pit is usually more than 2 cubic meters. m, while its walls must be strengthened in order to avoid possible scree. The drain is located a few meters from the shower, but not under the building itself and not at its walls - this will lead to the destruction of the foundation in the future, as well as to the appearance of unwanted odors.

Equipment example drain pit for a summer shower

The drain must be laid with a waterproof layer - roofing material, hydrostekloizol, PVC film or concrete screed(reinforced with metal mesh).

Attention! A common mistake is to use clay as an insulating material, which erodes and soon clogs the drainage ditch.

Installation of a frame for a temporary shower stall

If for a capital structure brickwork, then for the temporary, a frame is usually installed: metal or wooden. In the latter case, the tree should be treated with special impregnations that will protect it from insects and moisture, preventing the formation of fungus and mold.

Wooden frame for summer shower

1. Marking is done - a rectangle is indicated right on the ground, the sides of which correspond to the dimensions of the future country shower.
2. Wooden bars are installed, the width of which reaches up to 10 cm.
3. Ligation is performed - starting from the top, the structure is securely fastened with bolts, after which the beams-basis of the shower walls are connected.
4. Walls are equipped, for the construction of which you can use both boards and slate or plastic panels.
5. Piping is in progress - the plumbing is installed so that the outlet of the pipe under the shower hose is higher than the level of the head (this will provide the necessary pressure for the movement of water). For runoff, a conclusion is made to a sump or to a specially equipped septic tank.
6. A tank is installed - a tap is made with a thread, a tap with an appropriate nozzle is placed, after which the barrel rises and is fixed.

As a tank for a country shower, a plastic container, which can be purchased at a specialized store, or another barrel available on the farm, is suitable. It is desirable that it be flat and proportionate to the area of ​​\u200b\u200bthe building so that the weight is evenly distributed over load-bearing structure. Its volume is selected at the rate of 40 liters per family member, but the barrel should not be too heavy - its maximum volume is not more than 200 liters!

solar water heating tank

Advice! So that the owner of the cottage does not have to carry water into the tank on his own every time, you can equip it with automatic filling.

Country shower lighting and ventilation

When doing the wiring yourself, it is important to follow all the rules of electrical installation and adhere to safety precautions. Separately due to high humidity care must be taken to insulate the wiring.

Ventilation window for outdoor shower

Interior shower trim should be made of moisture-resistant materials: plastic panels, pieces of linoleum, oilcloth, etc. If wood is used, then each individual board is covered with hot drying oil.

The concrete floor is usually covered with gratings made of plastic or wood, rubber mats are laid on top. It is quite convenient to equip a small locker room directly in the shower room. In order to prevent water from getting into it, the floors in it rise slightly by a couple of centimeters - this is easy to achieve by additionally placing a pallet.

Summer shower interior

Concerning exterior finish, then similar materials that have already been used for decoration will look harmonious country house and other buildings on the site.

To use the shower not only in summer period, but also in the colder season, it is recommended to insulate it with expanded polystyrene, which fits into the interior and is upholstered with PVC film on top. The walls are usually painted or plastered, sheathed with clapboard or siding.

How to build a summer shower in the country: video

Types of summer shower: photo

Nothing relaxes so much after a hard day's work in the country as a summer shower. Water not only calms, but also refreshes, distracts from unpleasant thoughts and relieves stress. But what to do if there is no shower on the site? If you don’t want to splash around in a trough or basin, you need to take care of comfort in the field and design a refreshing summer shower for your favorite dacha with your own hands, using finished photos and drawings.

How to build a summer shower with your own hands

Summer shower occupies one of the first places among all suburban buildings. Sometimes this is not just a way to wash up after a day of cultivating the land has come to an end, but also the only way to cool off in the heat.

First you need to choose a place to install a shower facility. To do this, you should study your site for secluded places.

On the other hand, this place should not be far from the main building, so that you do not have to freeze on the way to a warm house if you decide to take a shower on a cool day.

Advice! If a solar heated tank is foreseen, make sure nothing is obscuring the water tank.

Once you have found a suitable location, select optimal dimensions for your cab. Please note that a person needs a room of at least 1 m 2 for ease of movement. If a dressing room is planned for changing clothes and storing dry things while bathing, the building is increased by another 60-70 cm. The height of the shower cabin is approximately 2.5 m. So, the estimated dimensions of the shower for giving are 170x100x250 cm.

If the structure is supposed to be wooden, then the next stage of construction will be the construction of a frame from a wooden bar or a metal corner.

Next are the walls. Please note that for better ventilation, the walls should recede from the ceiling and the pallet by at least 20-30 cm. The walls are built mainly from the materials that remained during the construction of the main summer cottage.

Water supply in the country shower

When installing a shower for a summer residence with your own hands, it is imperative to provide for the supply and discharge of water in advance. Drainage system is laid at the stage of foundation construction, and the supply of clean water is organized during the installation of the tank.

Summer is a great time for country rest. It can be overshadowed by the absence of a shower, since a person, regardless of whether he works or rests, needs to perform water procedures.

If the cottage is used only in the summer, then the easiest way to organize a shower is on the site. You can make a mobile shower, or build a solid outbuilding.

Portable outdoor shower

In stores you can find a foot shower. It does not require any construction or installation to operate. As a rule, only a small container of water is needed to use it.

An existing hose is lowered into the tank, which is connected to the pump. It looks like a small rug. Water comes out through a hose with a watering can, and for it to go, a person just needs to stomp in one place.

This device is simply indispensable, as it is suitable not only for summer cottages, but also for picnics, you can take it with you on trips.

With its help, water procedures can be carried out not only on the street, but also in the house, when it is very cool outside.

To do this, you just need to put a basin and wash. Another advantage of a mobile shower is self-adjustment water temperature. Such a shower in the country is simply not replaceable.

Stationary shower

Many summer residents are interested in how to make a stationary shower. This option is quite expensive compared to the first one. However, it will serve you for many years.

Before starting construction, it is necessary to consider where the water will drain from it. It is good when there is an antiseptic on the site. It can be drained from the shower.

If it is absent, then you need to make a hole, fill the bottom with expanded clay. A family needs a pit measuring 60x60x60 cm.

If sand predominates in the soil, the walls of the recess will have to be strengthened so that they do not crumble. For this, a metal mesh or boards that are no longer needed are suitable.

shower base

As a rule, the shower building weighs little. Therefore, it makes no sense to make a foundation for it, it can be replaced with blocks. They are leveled at the same level so that the structure is level.

It is much cheaper than the foundation, and takes much less time to build, since the foundation must dry out, and the building can be erected immediately on the blocks.

Blocks should be placed 20 cm from the ground, this is necessary so that the tree does not rot.

In the event that you are going to make a metal structure, then the blocks can not be aligned at a level of 20 cm. Such a frame can be installed on ordinary paving slabs.

Building

There are two types of building. The first is when the building is divided into several parts. In one part, a shower is made, in the other a dressing room or technical room where the boiler is installed.

Note!

The second type is a simple shower with a curtain, where only water procedures will be performed. Therefore, the dimensions of the soul are calculated from what kind of building is planned.

Frame types

Metal. The frame can be made of a profiled pipe, 3 mm in size. For work you need a welding machine.

Pipe joints are best welded, so the structure will be stronger. If the device is not available, then the joints can be fastened with special bolts.

Tree. For construction, you need a beam. Usually use a bar with a size of 50x50 mm. Before starting construction, it is necessary to make a drawing of the shower in the country.

shower sheathing

After the frame has been erected, the shower must be covered with material. There are no specific material standards. Everyone chooses according to his own pocket.

Let's highlight the most popular materials:

• oilcloth;
• the cloth;
• wood;
• slate;
• polycarbonate.

Water tank

Absolutely any container can be used as a tank. Basically, these are metal or plastic barrels. They can be purchased at any building, country stores.

Note!

When choosing, consider the region of residence. For southern cities, any capacity is suitable, but for northern regions only metal, as it heats up faster.

shower tray

It is best to purchase a pallet ready-made, as it will have a drain that will directly merge into the pit. The pallet is made of plastic or metal. Metal will last much longer, so it is advisable to choose it.

Making a summer shower in the country is not so difficult. The main thing is to thoroughly approach the design and calculate in advance the amount of material required.

For clarity, you can consider a photo of a summer soul in the country with your own hands. It will make your stay comfortable and enjoyable.

Do-it-yourself photo of the soul in the country

Note!