How to glue ceiling tiles on an uneven ceiling. How to glue ceiling tiles: step by step instructions How to glue walls with ceiling tiles

Modern manufacturers offer a lot of finishing materials for the ceiling in any texture, texture and color. Ceiling tiles are one of the most affordable materials for finishing the ceiling and budget repair... Can it be glued in the bathroom or on the walls of the room? Answers to these and other questions - below.

Before gluing the tiles to the ceiling, the surface must be prepared.

Preparatory work:

If there is whitewash on the ceiling, it must be blurred, the wallpaper must be removed, the paint must be removed. The ceiling must be completely cleaned of previous finishes. If there are remnants of old materials on the surface, in some cases this may pose a threat to the quality of gluing new tiles.
All noticeable irregularities, cracks, pits and other defects must be eliminated with a putty mixture on acrylic base or a sealant. If this is not done, then in places of obvious irregularities the tile will simply break or will not lie down and a large amount of glue will not save the situation. If you paste over (the use of the word paste incorrectly) with tiles a ceiling that has small irregularities, the aesthetic appearance will be spoiled.
When the putty is completely dry, you need to mark the ceiling. This is done with a chopping thread. The diagonal is cast, the center is marked on the horizontal.

The gluing process itself is in many ways simple: the glue is applied to the tiles either pointwise or around the perimeter and in the center, and the material is glued to the ceiling. If necessary, they can be adjusted and trimmed relative to the edge of the surface. Regardless of the chosen method of gluing, there are a number of specific recommendations already at the final stage.

Namely:

It is possible to grind the seams between the tiles only after the glue has completely dried. Otherwise, the tiles can be dislodged, peeled off or damaged.
Not worth pruning ceiling tiles too far from the wall, otherwise there will be gaps that will be difficult to close even with a ceiling plinth.
After the glue is applied to the tile, you should hold it for a few seconds and only then apply it to the surface.

If upon completion renovation works after a while, the color of the ceiling got fed up, the tiles can be freely repainted in any other shade you like. For this, dispersion or acrylic paints... If you do not take into account the fragility of the water emulsion, then this mixture is also quite suitable.

Ideas: how to glue ceiling tiles with a diamond and other methods

Methods for gluing tiles for the ceiling are in the options for its location on the surface. There are only four of them: in a row, a diamond (diagonally), "bricks" (with an offset) or in the form chess board.

Let's consider each method in more detail:

Diagonal or diagonal. First, you need to make marks on the diagonal and perpendicular markings. You need to start gluing from the center. The advantage of this method is that it will help to hide the curvature of the walls. The disadvantage is a lot of waste.
Method in rows- the simplest and most common. The tiles are laid parallel to the walls along the perpendicular markings. You should also start laying from the center, but you can still start from the window.
Checkerboard method includes the use of tiles in two colors. Installation starts from the center of the ceiling. The tiles are laid in rows with alternating colors.
Way " brickwork"Or with offset may include one tile color, two or more. The starting tile is laid from the center of the ceiling, the subsequent elements are shifted relative to the previous row to the side by half a tile or by a third (quarter). Each row is offset.

The last method with an offset looks interesting in several color schemes if the use of "rainbow" allows the interior.

Wet rooms: is it possible to glue ceiling tiles in the bathroom

Ceiling tiles are made from environmentally friendly materials, they are practical and unpretentious to maintain.

There are different types of tiles, they differ in the manufacturing method and technical characteristics:

Pressed(stamped) tiles are the most affordable and widespread. They are versatile material for all premises.
Cast elements cast in factories in special forms... This type of production is considered more reliable, and it is just that it is recommended to use it in rooms with high humidity levels.

The process of finishing the bathroom ceiling itself is not much different from the standard gluing of tiles to the ceiling. After preparation, the surface should be primed for better adhesion. According to the markings, the tiles in the bathroom can be laid in any suitable way.

Options for using ceiling tiles on walls

On the walls, ceiling tiles can be used as a panel at the head of the bed or, for example, to decorate a fragment of one of the walls. A wide selection of textures, textures and colors allows you to make budget decor very refined. Americans have been using this decoration method for a long time.

There are several options for using ceiling tiles on walls:

As a decor, instead of photowall-paper, one of the walls is pasted over with relief tiles completely from floor to ceiling.
You can completely paste over all the walls of the room with this tile, adjusting the patterns.
Ceiling tiles are excellent a budget option for wall decoration in patchwork style. To do this, you need to have tiles with different patterns and colors, the more options - the better.
The use of ceiling tiles as a material for a panel at the head of the bed or above the tea table creates an undeniable effect.

For walls, depending on the type of use, ceiling tiles of any type can be used, however, it should be remembered that the material is not resistant to mechanical damage and is capable of deformation.

Different ways: how to glue ceiling tiles (video)

When using ceiling tiles to decorate walls or ceilings, it should be remembered that the glue sets rather quickly, so the sluggishness of the work will only interfere. During the gluing process, it is important to monitor the joining of the plates and not leave gaps. Elements cut off at the walls are hidden by a skirting board. If finishing is in progress different kinds tiles, you should first lay out the pattern on the floor, then move the elements to the ceiling or wall. Compliance with the recommendations of specialists is a key rule, thanks to which even beginners home master can do the right quality repairs.

Happy experiments!

Technique of pasting the ceiling with foam tiles, different methods and schemes of fastening, selection suitable materials and helpful installation tips.

Preparatory work before installing ceiling tiles

You need to start gluing the ceiling before cladding the walls, since glue can stain the wallpaper. However, if the replacement of the decoration on the walls is not planned, and the ceiling needs to be pasted over, then the wallpaper can be closed plastic wrap... Almost any type of surface (wood, concrete) can be pasted over with foam plastic ceiling tiles.

For the reliability of fixation and durability of the coating, we prepare the ceiling:

We remove the chandelier and insulate the ends of the wires.
Getting rid of old finish... At the same stage, we tap the surface for the presence of unreliably fixed elements. In the corners and at the joints, it is more convenient to do it with a screwdriver.
We remove stains of rust, mold, mildew, soot and grease with special antiseptic solutions. If you skip this stage, then all traces will eventually appear on the new cladding.
We make a thick mixture of cement-based putty and cover large cracks in the presence of.
We prime the ceiling with a deep penetration compound with antifungal components. Please note that a deep penetration primer can be prepared at home by diluting PVA glue in water in a ratio of one to three.
At the same stage, we evaluate the evenness of the coating. If the drop and potholes are significant, then we level them with a layer starting putty... Then we rub the roughness with sanding paper and primer with acrylic compound. If the irregularities are insignificant, then the tile itself will mask them.

The tile can be glued even on the whitewash, if the ceiling is even, but it is important that the whitewash layer does not crumble or crumble. In addition, the whitewash will need to be primed before gluing to improve adhesion to the adhesive.

Types of ceiling tiles for the ceiling

In the process, we need the ceiling tile itself and the glue with which we will fix it to the surface.

According to the method of production, tiles are:

Pressed... This expanded polystyrene ceiling tile is made by stamping. Its thickness is usually 6 to 8 mm. Elements of this type are most often found defective.
Extruded... Produced in blocks. In the manufacturing process, a film-coated polystyrene strip is used, which is intensively pressed. Products are distinguished by a higher density compared to pressed tiles, smooth and shiny surface, and their thickness is usually 2.5 mm. There are models that imitate wood, marble and others natural materials... Such tiles can be pasted over the ceiling in the bathroom, since it has increased moisture-resistant characteristics.
Injection... Products are produced by sintering raw materials in special molds. The pellets are not destroyed during production. And therefore, in the end, the tile turns out to be correct. geometric shape with a deep pattern. Thickness - from 9 to 14 mm.
Seamless... Such a coating looks as aesthetically pleasing as possible, since it has no visible seams. This material will cost more, but it looks more aesthetically pleasing.

Having decided on the type of ceiling tile, Special attention give it quality. To do this, when buying, consider the following features:

Each element should be geometrically correct, the sides should be even, the corners should be 90 degrees. Otherwise, when gluing, there will be uneven seams and rows.
The finer the grain in the polystyrene foam tile, the better it is. However, make sure that the product does not crumble or crumble around the edges.
The pattern must be uniform, free from defects, and the pattern must be clear and symmetrical.
Traditionally, tiles are produced in sizes 50 * 50, therefore calculate required amount elements are not difficult, knowing the area of the ceiling. Much less common rectangular models extruded tiles with dimensions 100 * 16.5 cm.

Please note that it is important to purchase the material with a 10-15% margin. Otherwise, you will have to buy from the next batch, and it may differ in shade or other details.

The choice of adhesive for tiles on the ceiling

As for the adhesive for ceiling tiles, then its selection should be taken no less seriously than the choice of tiles, because the durability of the finish, the reliability of fastening, and ease of use depend on it. It is important that it does not have a too thick or too liquid structure. Only in this case it will lie down in both a thick and a thin layer, which is very important if the ceiling has slight irregularities.

For gluing the ceiling with tiles, different compositions are used: putty, drywall glue, liquid nails, polyurethane or acrylic glue.

First of all, the choice of the composition depends on the type of surface. Tiles can be fixed to a leveled ceiling with liquid nails, polyurethane and acrylic glue. But if the surface is uneven, then it is better to use a putty. It will be evenly distributed over the surface and will provide a secure fit.

When purchasing materials, do not forget about skirting boards for masking joints with walls, a socket for a chandelier and other decorative elements.

Creating a drawing and marking a ceiling for tiles

Before starting work, you need to draw up a scheme according to which the tile will be fixed. The most common location options are: parallel, diagonal, combined (staggered, snake, perimeter).

Depending on the chosen method of placing the tiles, you need to make a ceiling marking. For this you need a tape measure, laser level and chop cord.

We carry out work according to the following instructions:

For parallel fastening, the marking line is applied from opposite corners. They should intersect in the center.
For diagonal fastening in the center of the ceiling, we beat off the lines connecting the centers of the opposite walls with a paint cord.
Parallel to two axial over the entire surface with a step of 0.5 meters ( standard size ceiling tiles) we draw lines.

Do not rely on the eye and start gluing without marking, as uneven gaps will completely ruin the result.

Parallel fixing of ceiling tiles

You need to start gluing the tiles using this technique at the wall opposite from the door. Better yet, from the most visible angle.

We carry out the work in the following sequence:

We apply glue along the perimeter of the wrong side of the tile and in the middle with a cross. It is not recommended to lubricate with an unnecessarily thick layer. Otherwise, sloppy marks will appear along the edges, and the seams between individual details will become much more noticeable.
Press the tiles tightly to the surface and smooth them in one plane. This is necessary for the adhesive to adhere evenly.
We first join the next element with the previous one and only then press it against the coating. Please note, be sure to pay attention to the symmetry of the pattern.
In this way we glue the entire ceiling to the edge.
Having reached the extreme row, measure the distance from the seam of the previous tile to the wall with a ruler and cut off the desired part with a clerical knife. It is not recommended to cut off several at once. It is best to take a new measurement for each row as the walls may be uneven.

At the end of the tile gluing process, it is necessary to close the gaps decorative skirting boards... They are usually made of the same material and adhered to the same adhesive.

Diagonal installation of ceiling tiles

It is more convenient to start fixing diagonally from the center of the ceiling. If this location is planned to be installed lighting fixture, then the edges of the tiles will have to be cut off. In the future, the hole can be closed with a decorative plug.

In the process, we adhere to the following instructions:

According to the markings made, we attach the first tile in the center so that there is a line in the middle for each corner.
We fix the second part along the axes marked on the ceiling.
We glue the tiles along both axes from the center to the walls.
We attach the rest of the details.
For installation on the extreme row, cut out suitable element, having previously measured the required distance with a ruler.

After the ceiling is completely pasted over, you can remove excess glue near the seams and pencil marks, if any, with a damp cloth.

Block gluing of ceiling tiles

The essence of this method is to fix four elements at once and align them along one plane. It is most often used when pasting an uneven ceiling with a putty.

We carry out the work in the following order:

Using a notched trowel, apply the adhesive to the ceiling under the area of the four slabs. Using this tool allows you to immediately apply a layer of the desired thickness.
We attach four parts at once and join them together.
Using a two-meter level or rule, we align all elements with respect to the ceiling and with each other.
Along the marked line, lay a row of two tiles to each wall in sequence. In this case, the parts must be positioned so that their joint passes exactly along the axis.
We attach the rest of the elements according to the markings applied.
We make the extreme row from the prepared segments.

Please note that during the process of pasting a ceiling with irregularities, be sure to use building level... This method is a little more complicated, because it is recommended for beginners to initially level the coating with putty, then proceed to gluing the ceiling tiles.

The technology of fixing tiles to the ceiling is not particularly difficult, and with the right approach, even a beginner can cope with it. However, some tricks will help you avoid mistakes and make your work much easier:

Before starting work, leave the tiles in the room where the installation is planned for a while. This is necessary to adapt the material.
The combination of tiles of several colors looks original. Such a combination can be placed in a rhombus, in a checkerboard pattern, or in another pattern, depending on your preferences.
A small arrow is usually applied to the seamy side of the slabs. Make sure that on each part it looks in one direction.
To prevent the formation of teeth on the coating and the seam to be lost, it is not recommended to interrupt the process in the middle of the row.
If it is necessary to wipe the gaps in some places, then this should be done only after drying. adhesive composition... It is best to do this using a putty or sealant. If the grout comes into contact with the tiles, immediately remove it with a wet brush.
The tile will press more tightly against the ceiling if you do not hold it with your hands, but wooden block for uniform distribution load.
In order to save money for pasting, you can use transparent compositions on a liquid "rubber" basis. Their consumption is much less, however, in order for the part to be fixed securely, after applying the glue to the tile, you need to wait a little until it dries.
It is not recommended to install high-power lamps at a distance of less than 20 cm from the covering, as the polystyrene foam can melt when exposed to high temperatures.
If you preferred foam tiles, then keep in mind that water-based paint for her finishing will not work, since it will begin to flake off in a year. The best option for these purposes - a dispersion composition based on acrylates.

Watch a video on installing ceiling tiles:

We figured out how to glue ceiling tiles in several ways. With the help of step-by-step instructions, you can independently prepare the surface, select the material and perform the fastening in any way you like. Correctly fitted and fixed tiles will not look like budget finishing... Staining or combining several colors allows you to create original design ceiling.

One of important details quality repair- beautiful and flat ceiling. Some are limited to whitewashing, others acquire tension options... One of the popular ways is to glue the ceiling tiles. How to carry out the installation so that the material holds firmly and decorates the room? A selection useful tips presented in this article.

Material characteristic

Ceiling tiles are finishing material from foam. Usually sold in squares, but rectangular patterns are also found. The most common size is 0.5 × 0.5 m. The front side is smooth and embossed, laminated or without any coating. Tile decor can imitate wood, fabric, ceramics, stucco and other structures.

There are three types of finishing materials:

injection is obtained by sintering and casting polystyrene foam in special forms;
extruded is pressed from an extruded strip, usually film-coated or colored;
pressed is made by pressing.

There is a so-called seamless tile. Its advantage is that at the end of the work, the joints are completely invisible. They usually have a curly edge: when glued, the wavy joints on the ceiling become invisible. Installation of such a coating is carried out with millimeter accuracy and only on a flat surface.

Ceiling tiles are a way to quickly and cost-effectively decorate a room. When the ceiling is designed in this way, it is called "papered" or "glue".

Pros and cons

Why is it worth giving preference to polystyrene foam tiles for the ceiling? Material advantages:

It is environmentally friendly.
One of the main benefits is affordability. Styrofoam tiles are inexpensive and common.
A wide range of reliefs allows you to choose an option for any interior.
Suitable for finishing most base surfaces: concrete, brick, wood, plaster and plaster.
Has a soundproofing property.
Helps keep the room warm.
Do it yourself easily and quickly.
Allows you to correct the result without any problems after a while (for example, to re-glue the detached part).
Aesthetic look.
Helps to hide minor defects in the ceiling (potholes, cracks).
The material is not flammable, therefore it is allowed to glue it near heating systems.
Such material is easy to care for: it can be cleaned, wiped with a damp cloth. If the coating is not laminated, then it is cleaned with a soft nozzle of a vacuum cleaner or a dry cloth.

The material also has a number of disadvantages:

It melts at temperatures above +80 degrees, so the lamps should not be located closer than 30 cm.
Turns yellow over time from sunlight.
Some coatings do not tolerate moisture well.
On an uneven ceiling, it is difficult to achieve uniformity due to the abundance of joints.
Poor air permeability, which makes the room more stuffy.
Brittleness: Thin sheets are easily deformed and damaged as long as they are not fixed to the ceiling.

What to glue on

In order for the finishing material to last for a long time, you need to choose a good adhesive for the ceiling tiles. The final result and the durability of the coating largely depend on the choice.

What to glue the polystyrene foam squares on:

"Moment"- one of the most commonly used formulations. Its advantage is that it dries up very quickly, which justifies its name. It is enough to press the tile to the ceiling for a few seconds. Of the minuses, it is worth noting the high cost and high consumption.
- universal adhesive based on polymers. It is used for gluing tiles, ceiling plinths and other materials: linoleum, parquet, etc. After drying, it remains transparent, which ensures the preservation aesthetic appearance cover. It grabs longer than "Moment", so you have to hold the tile longer, which is not always convenient.
Eco-Set- glue similar to Titan. Plus - when working, you can adjust the position of the tiles. Minus, like Titan, is a relatively long polymerization.

How to carry out the installation correctly

What items will be needed for a successful installation:

a stepladder (or a high stable table);
glue gun;
stationery knife;
ruler (tape measure);
pencil;
putty knife;
brushes;
twine;
wiping cloths;
protective gloves and mask;
glue and tiles.

Training:

First, make sure each tile is free of contamination.
Sheets with curled edges and other defects are not used. For this reason, you should buy material with a small margin. The defect can be found when unpacking the pack, but during installation, the material can be easily damaged if handled carelessly. It is recommended to purchase ceiling decoration 10% more than necessary.
Before starting repairs, it is better to remove all the furniture from the room. If this is not possible, then big ones will come to the rescue. plastic bags, with which it is worth covering objects.
Close vents, windows and doors - glue ceiling tiles it is necessary strictly for room temperature and without drafts.
Be sure to disconnect the power supply in the room.
Make a rough drawing on a piece of paper to get a better sense of the quantity required tiles and its location on the ceiling.

Substrate preparation is one of the most important stages... The surface must be clean and as flat as possible. It is recommended to clean the ceiling from old finishes - plaster, whitewash, etc. A spatula will help to clean the ceiling. Then, if necessary, re-plaster or putty and cover with a primer. Tile will hide minor defects, but it is better to eliminate noticeable irregularities.

Advice! Washing off whitewash and primer to concrete is a difficult and time-consuming process, and, moreover, it is very dirty. When using an adhesive with good adhesion, only the whitewash can be washed off.

The main ways to install the ceiling plate:

parallel to the walls - the most convenient;
diagonally it looks very nice, but it will take more material and time to finish the edge of the ceiling (it will lie in triangles or incomplete squares).

How to properly glue ceiling tiles:

The first stage is marking the ceiling. The squares are glued from the center to the edges. How to quickly determine the middle of the ceiling? Pull two twines diagonally from the corners. The point of their intersection is the center. It should be noted. Further, two perpendicular lines are drawn through the point, which will divide the ceiling into 4 parts. Tiles will be attached along these lines. To be sure, you can mark the entire ceiling by drawing the location of each detail of the coating.
The glue is applied to the sheets in a thin layer or pointwise using a special gun. The lighter the material, the less glue you need to attach it. Pay special attention to the edges and the middle.
The first tile is pressed to the center of the ceiling, guided by the markings. Place the first four squares. Their corners should touch at one point, the central one.
Next, you need to glue on other panels, guided by the markings and the position of the previous parts. All joints must be tight, without gaps.
Remember to wipe off excess glue with a damp sponge or cloth.
Tiles placed against a wall are cut to size with a sharp knife, such as a shoe or wallpaper, along an iron ruler or square. First, the desired part is cut out, and only then the glue is applied.

What if the ceiling is uneven? In this case, gaps are formed between the tiles. The seams are easiest to rub over with a white acrylic sealant. After grouting, the excess is removed with a damp sponge.

Advice! If the tile covers the chandelier mount, make a suitable hole in advance, insert the wires into it and glue the tile. Remember to turn off the electricity before this operation.

The finishing of the ceiling is completed by gluing the ceiling plinth. The adhesive for this material is the same as for the tile. One condition: the composition must be transparent after drying. Otherwise, if accidentally hit on the front side, it will spoil the view.

Several rules for attaching skirting boards:

Start on the opposite wall from the door.
Cornices in the corners are cut at an angle of 45 degrees.
The glue is applied on both sides: one is in contact with the ceiling, the other with the wall.
Gaps and joints in the corners are perfectly masked if you cover them with sealant.

For the repair to be a success, you need to take into account many points that not everyone can remember right away. What you need to know about ceiling tiles:

After purchase and transportation, allow the panels to rest at room temperature to avoid deformation during operation.
Soft tiles at the time of gluing will be correctly supported by a wooden block. The material deforms from pressing with your fingers.
Sometimes the sizes of the tiles do not match. This is imperceptible to the naked eye, but manifests itself during the editing process. To avoid inconsistencies in the pattern, attach a square, not smeared with glue, to the glued tile. If the size matches, the installation continues. If it does not match, you will either have to leave a gap, which you will later need to wipe with a sealant, or (preferably) take another sheet.
Do not press the expanded polystyrene too hard. This will not accelerate the setting of the adhesive, but it may dent.

Pasting the ceiling is an important part of the renovation. The successful completion of the finishing is possible only with the right choice glue, correct calculations and accuracy during installation.

Lightweight foam tile is the most sought after ceiling covering. With its help, they transform the space in kitchens, hallways, bedrooms and even in halls for receiving guests. First of all, people choose this finishing material due to the fact that, in comparison with stretch ceilings it costs a mere penny.

And, of course, everyone, without exception, likes the fact that even the person who makes repairs with his own hands for the first time in his life can handle such gluing. For such beginners, we will tell you how to properly glue the tiles to the ceiling and what methods you can do it.

How to glue foam ceiling tiles correctly and beautifully: different ways

Scheme No. 1

Scheme No. 2

For those who do not know, ceiling tiles are squares with perfectly straight sides, which have a front and a back side. In view of this, when carrying out finishing work, you must carefully consider whether you are fixing them correctly on the ceiling.

After all, if you glue the tiles, not paying attention to this nuance, then in the end you will not be able to fold the perfect pattern. Also, when planning such work, it is extremely important to determine in advance what method you will glue the tiles. This needs to be done in order to understand exactly how much material you may need.

Methods for gluing foam to the ceiling:

Parallel to the wall. This method finishing assumes that Finishing work will begin to be carried out against the wall that is opposite the window or doorways... The first tile will need to be spread with glue and laid exactly parallel to the wall, stepping back a little from it.
Diagonally. If you choose this particular method, then you will need to start finishing the ceiling exactly from the center of the room. In order to locate this location, you will need to pull the thread through the corners opposite each other. The place where they intersect will be the center of the room.
Diamonds. Immediately I want to say that this method is considered the most difficult, so it is better for beginners not to take it. In this case, you will also need to find the center of the room, set aside several squares from it, and then glue tiles diagonally from them. If you do everything correctly, then the corner of the tile will point exactly to the center, and one side will coincide with the diagonal on the ceiling.

How to mark the ceiling under the ceiling tiles?

Recommendations for marking

As mentioned a little above, in order for the ceiling tile to look perfect, it is necessary to carry out preliminary marking before fixing it. Remember, if you do not want to redo all your work from the very beginning, you must do it.

After all, only the markings correctly applied to the ceiling will help you to place the first tile as it should, and subsequently create the perfect pattern. If you attach the tiles to the ceiling with rhombuses or diagonally, the markings will help you mask the seams as well as possible, thereby making the canvas visually even.

To start with measuring tape measure the approximate distance (diagonally) from one corner of the room to another
Next, cut two pieces of rope (their length should correspond to the received data)
In the next step, you will need to stretch these two blanks from corner to corner so that they intersect in the center of the ceiling.
Next, take, for example, a level and a simple pencil and draw the resulting diagonals on the ceiling space, and be sure to mark the center point of the room
Remove the ropes and draw a square near the center point that the ceiling tile can easily fit into. From this place, you will continue to finish the entire ceiling covering.

Where to start gluing ceiling tiles?

You need to start finishing the flow from the central point.

If you carefully read our article, you probably realized that you can start gluing the slab to the ceiling from two places. If you are doing this for the first time, it will be better if you give preference to the method in which the tiles are glued parallel to the wall. In this case, you will not need to carry out any preliminary measurements, and you can literally immediately go to the main stage of work. All you have to do is find perfect place on the ceiling covering and fix the first plate on it.

After fixing it, you will need to check if you placed it correctly, and you can move on to fixing the rest decorative material... If you want to create a more complex pattern on the ceiling, then you will need to apply markings on it (we told you how to do this correctly above) and after that you can start transforming the living space. In this case, the first tile will need to be placed in the center of the room to be repaired.

How to apply adhesive to ceiling tiles?

Glue application scheme

Most people who make repairs for the first time in their lives think that applying glue to a finishing material does not require any special knowledge. But as practice shows, even such a simple, at first glance, process must be carried out correctly. If you apply the glue randomly, then in the end the tile will not fix as it should and, what is most unpleasant, the resulting seams will not perfectly adhere to the ceiling covering.

So, first, apply a small amount of glue to the very center of the tile, then put the droplets diagonally from this point, and at the very end, draw a line around the entire perimeter of the finishing material. When applying glue to the tiles, make sure that the droplets are not very large. If there is a lot of glue, then when the tiles are pressed against the ceiling, it will begin to come out and, as a result, you will have to remove the excess, and this can damage the structure of the finishing material.

Yes, and remember, if you want the adhesive to fix the tile to the ceiling as well as possible, you will need to hold it in the air for 1-3 minutes before fixing it. During this time, the glue will react with air and this will contribute to the fact that the substances that are responsible for adhesion become more active.

Which adhesive is best for ceiling tiles?

Ceiling tile adhesive

As a rule, people think that the more expensive the glue, the better it is. Of course, in most cases, an expensive product is much better than a cheap one. But still, in the case of ceiling tiles, you need to pay attention to other factors. The most important indicator of the quality of the adhesive is the adhesive strength. The higher this indicator is, the more reliable the decorative material will be fixed on the ceiling covering.

In addition, you should pay attention to how quickly the glue dries. The faster this happens, the better it will be for you. After all, if it seizes not 30 seconds, but 2-3 minutes, then you will simply get tired of holding the tile for such a time and, most importantly, you will definitely not be able to fix it correctly. Also, when buying, be sure to pay attention to the viscosity of the adhesive.

If the glue you have chosen is very liquid, then try to choose another option for finishing work. As practice shows, a too liquid glue base will not allow you to reliably fix the tile to the ceiling and it is likely that after a while you will have to redo everything from the very beginning.

Types of adhesive for fixing ceiling tiles:

Universal
Titanium
Adhesive compound (silicone based)
Acrylic putty
Liquid Nails
Polyvinyl acetate adhesive

How to beautifully and correctly glue the ceiling tiles diagonally, with a diamond: description, video

Before proceeding with fixing the tiles, it is imperative to prepare the ceiling space. If you do not do this, then in the end, with all the desire, you will not be able to fix the finishing material correctly. For this reason, it will be better if you first carefully examine the ceiling and repair any defects.

But keep in mind that in order for the tile to fit perfectly, it is not enough to patch up all the cracks and pits. If you want a grip between the ceiling and decorative coating was the maximum, then you will definitely need to polish the surface, and then prime it thoroughly.

First, measure the area of the ceiling and estimate how many tiles you might need. Note that if you fix it with a diamond, then you may need it more than if you glued it diagonally.
At the next stage, you will need to mark up and mark the central point of the ceiling, as well as the diagonal lines, which you will use to lay out the diagonals and rhombuses.
After the markings are done, you will need to apply glue to the entire tile and fix it to a center point. If you want it to take hold instantly, do not forget that it must be kept for at least 1 minute.
In order for the tile to fix, it must be pressed against the ceiling covering and held in this position for 30 seconds. Once you've made sure it doesn't move, you can start applying glue to the remaining decorative material.
Initially, you will need to lay out the tiles along the diagonals that were drawn during the layout, and when this is done, you can proceed to filling in the empty space.
It is necessary to fix the tiles on the ceiling, moving from the central point to the corners, while trying to ensure that they visually fold into a perfectly straight line.

How to properly glue ceiling tiles without seams?

Bonding seamless tiles

In principle, seamless tiles are glued in the same way that we introduced you a little above. Therefore, in this case, you will need to initially measure the area of the ceiling in the room being repaired, apply markings on it, determine the center point, and only then proceed to gluing the decorative material. But still, if you want to end up with the perfect ceiling covering, then glue the tiles either diagonally or parallel to the wall.

Yes, if you give preference to the last method of finishing the ceiling, then start fixing the tiles on the wall opposite to the window. This little trick will help you make the gaps that are formed when trimming with this material are less noticeable. And finally, I would like to say that, although some sources claim that in the case of seamless ceiling tiles, it is not necessary to apply glue around its entire perimeter, it still needs to be done.

As practice shows, if this is not done, then after drying, the gap formed during installation is quite striking. And, of course, do not forget that the ceiling tiles are made of very soft material, therefore, it is necessary to hold and smooth it not with your hands, but foam sponge or a soft cloth.

How to properly glue ceiling tiles to uneven ceilings?

Bonding ceiling tiles to uneven ceilings

As a rule, ceilings in old houses and apartments are far from ideal. Most often, they are covered with cracks and small depressions, which are very striking. If you live in a house with the same ceiling covering, then if you wish, you can fix appearance dwellings with ceiling tiles.

If you don't want to mess around with leveling and sanding the ceiling, then just buy a foam tile and glue it parallel to the wall in a way. True, you must remember that you can do this if the defects on the ceiling are the smallest. If they are too large, then you will either have to decide to completely pull out the surface or to install a special frame.

Usually it is installed slightly below the ceiling itself and this makes it possible to hide even very prominent defects. True, in this case, more expensive tiles, for example, wood, metal or ceramic, will have to be fixed on it.

How to seal the joints between ceiling tiles?

Recommendations for sealing ceiling tiles

As mentioned a little above, even the so-called seamless tile requires additional processing gaps that form after the ceiling sheet is completely dry. In view of this, when planning such finishing work, immediately include in their cost special means which will help you to make the repaired surface as flat as possible.

As for how to do it, then in this case it is best to give preference to acrylic sealant. In case you want to seal the seams without any problems, then invest in a sealant in a tube and a gun that will help you distribute it evenly.

Secure gun to sealant tube
Using scissors, cut off the tip at a 45 degree angle
Press the resulting hole to the beginning of the seam
Smoothly press down on the pistol grip and guide them exactly along the seam
After filling the joint, carefully move the gun away from the ceiling and allow time for the sealant to cement.

Can ceiling tiles be painted?

You can paint the ceiling tiles

Sooner or later, the desire to paint the tiled ceiling appears in all people. But as practice shows, only a small part of novice repairmen decides to take this step. Most of these people believe that paint will simply ruin the ceiling tiles and they will have to spend more money on expensive repairs. In fact, not all tiles can be painted.

For example, in no case should a seamless tile be treated with dyes, as this will necessarily make the seams darker and, as a result, they will stand out quite strongly against the general background of the room space. The rest of the tiles can be painted calmly, but keep in mind that in order for the color of the renovated ceiling to be as saturated as possible, paint will need to be applied in at least two layers.

How can you paint your styrofoam ceiling tiles?

Ceiling painting scheme

As for the choice of paint for updating the ceiling, when buying it, you need to pay attention not only to the color. If you want the ceiling to remain in perfect condition for a long time, you must choose the right coloring agent.

This means that it must prevent the growth of mold, be moisture resistant and have dust-repellent properties. In addition, it must have a moderate level of glossy effect. In view of all this, we can definitely say that it is best to paint the ceiling tiles with water-based or acrylic paint.

Video: K How quickly to glue the CEILING TILES?

Styrofoam ceiling tiles are the most common, affordable way to renovate a ceiling. Everyone tries to approach it responsibly and individually. Before gluing the ceiling tiles, you need to preparatory work for a beautiful ceiling, with original finish pleasing to the eye for many years. Choosing a finishing option, everyone tries to approach it responsibly and individually. He tries to familiarize himself with the varieties of this material, the rules for calculating the required amount, what glue to glue, as well as some of the nuances of combining tiles with the interior of the room.

Ceiling tile types

On the construction market ceiling tiles are represented by the following varieties, differing in the methods of their production:

Pressed ceiling tiles are made of polystyrene blocks by stamping. Thickness finished product min - 6 mm, max - 8 mm.
Extruded blocks are produced from polystyrene strip by pressing. They have a shiny, smooth surface. The plates can be structured like a marble slab, a cut of a tree trunk and other natural materials.
For the manufacture of injector ceiling tiles, a method is used in which the raw material is sintered. As a result, the product correct shape with a deep pattern. Its thickness is from 9, but not more than 14 mm.

Selection of ceiling tiles by physical parameters

In order to properly glue the tiles for the ceiling, during the purchase, you need to pay special attention to the geometry of the product. If a tile is selected in squares, then all its corners must correspond to the required parameters, that is, equal to 90º. The slightest deviation in the future will lead to the formation of uneven seams. The corners of the ceiling tiles must not be rounded or pinched.

Another indicator when choosing a ceiling tile is the material from which it is made. When buying polystyrene tiles, you need to make sure that the edges do not crumble, and all the grains are the same in size. Higher quality is considered to be the one in which the grain size is especially small. Expanded polystyrene plates should not break under their own weight if held at any of the corners while suspended. The selected ceiling tile should have a clear pattern. No flaws are allowed, any minor inaccuracy or dent will immediately attract attention.

Calculation of the required amount of material and the choice of adhesive

After choosing the type of ceiling tile according to its physical parameters and external design, it is necessary to determine how many tiles will be required for the entire ceiling area. More experienced owners immediately buy 10-15% more in case of rejection due to broken corners or mistakes during pruning. In general, the calculation is not difficult. It is necessary to know the area of the ceiling and the size of each element. Typically, ceiling tiles are produced with the dimensions of the side faces 50-50 cm. If the dimensions of the ceiling are not a multiple of the length of the side of the tiles, then during finishing there will be gaps along the edges of the ceiling. Therefore, when calculating such a nuance must be taken into account.

An experienced craftsman's advice: if you want to save on glue, instead liquid nails it is better to use a transparent glue with a thinner “rubber” base. Its consumption is significantly lower. But for a strong fixation, be sure to dry the glue already applied to the tile a little.

Having calculated the required number of tiles, you need to decide what kind of glue to glue. Many people use "Titan", "Econaset", "Liquid nails", "Moment". They adhere well to all surfaces and dry quickly. After gluing, the tiles adhere firmly. Only for this it is necessary to press it against the ceiling for a few seconds.

Work order

Many owners of apartments and private houses prefer to glue the ceiling tiles with their own hands. Therefore, it is important for them to know that work must begin with marking the center of the finishing area. To do this, from diagonally located corners, you need to stretch two threads. Their intersection is the desired center. If there is a chandelier in the room, then you can start work from this point. In this case, the docking angles at the luminaire wire are slightly cut off. As a result, they will be closed with a curly glass of the chandelier rod.

Many start working from one of the walls and lay the tiles row by row. This option is the simplest and fastest. But there is also a small nuance here. It is better to lay the first row from the wall opposite the window or front door... Then the gaps that are closed by partial fragments will not be so noticeable.

Before proceeding with the sticker, the ebb around the edges of the product must be carefully cut off. In this case, the surface of the ceiling will turn out to be perfectly flat, without seams. It is also necessary to strictly observe the symmetry of the pattern at the joints of the tiles. The slightest deviation violates the entire integrity and beauty of the finish.

There are relatively many options for the location of the ceiling tiles relative to the walls of the room. The most common are parallel and diagonal with respect to the edges of the intersection of walls and ceilings. You can choose from plain, color and combination tiles. From combined options styling is most often practiced the following:

alternating or intersecting diagonals,

staggered

snake

along the perimeter of the ceiling or in its center, etc.

At the end of the work, skirting boards are installed around the entire perimeter. They are glued with the same glue as the tile itself.

Options for gluing ceiling tiles to whitewash

We will glue directly to the whitewash, so you should choose one of two ways:

The first is that on top of old whitewash a primer is applied. It is absorbed into the layer of the old coating and adheres to the main surface of the ceiling. Then you need to wait until the primer is completely dry and start finishing.

The second method involves partial scraping of the falling off whitewashed layer with a spatula. As a result, a thicker layer of glue is applied to the seamy surface of the tile, and it is pressed for several minutes to the gluing site. The glue is absorbed through a thin layer of whitewash remaining on the ceiling and sets to the overlap.

How to glue ceiling tiles with your own hands: video instructions

Ceiling renovation is a laborious and costly process. In addition to tiles, you can arrange tension and suspended structures, mirror panels of various configurations and sizes. Here everything is decided by the financial capabilities and the owner's fantasies.

(No ratings yet)

Discussion:

Andrey said:

I just peeled off the whitewash where the glue will be applied. I bought superglue (putty glue sold by sellers proved to be so reliable in operation). I smeared them only the places of the sticker at five points, pressed it to the ceiling and that's it. The tile holds. I did not close the seams - there was no great need. Later ceiling plinth- that's all. The ceiling is pleasing to the eye. Better than any whitewash. And faster and cheaper than suspended and stretch ceilings.

Svetlana said:

My husband and I glued the tiles to the ceiling in the living room on our own. Now I already know what to look for. Important note - it is important to process the seams the right material... We had to take silicone right away, but we confused it and took white glue. As a result, our seams turned yellow after drying, the ceiling looked terrible. The only solution began to paint the ceiling with paint to close the seams.