How to attach a ceiling lamp to a chandelier. Fixing the chandelier to the ceiling with a mounting plate

A chandelier is both a lighting fixture and an important decorative element, so many of them are quite heavy and complex structure. The installation of the luminaire becomes milestone repair, because even the safety of the inhabitants of the room will depend on the reliability of its fastening. To understand how to attach a chandelier to the ceiling correctly and with minimal cost, you need to know what kind of lamps for rooms are and how their installation methods differ.

Omitting the details of decorative differences between chandeliers, let's focus on what is important for the installation process: classification by type of fixture. On this basis, two main types of devices are distinguished:

• ceiling mounted with a hook;
• console, which are mounted on brackets or special strips.

Mounting the chandelier on a hook and on a bar (bracket)

Heavier models belong precisely to the first category, since only the hook can securely hold massive structures. The same models, which have less weight, are conveniently mounted on different types strips that can be attached to false ceiling profiles.

Mounting types

How are they structured different mounts? The hook is most often already built into the ceiling, however, if it is not there or it is unreliable, you can make it yourself. There are several types of structures that are used for such purposes, one of which is a collet stud. It is a collet, which is practically used as a dowel, and a stud that replaces the self-tapping screw, on which the hook clings.

Types of collet studs

You can use another option: a metal anchor or a self-tapping hook. When the chandelier is attached to the plasterboard ceiling in this way, the chain can also be included in the design. There is also a variety of hooks that are used to hang light fixtures from plasterboard ceilings and are called "butterfly" for the drop-down design, which prevents the fasteners from falling out of the hole in the profile.

Ceiling hook for chandelier

As for the mounting strips, they are fastened with dowels and screws. Long screws can also be used. Console models of chandeliers are often mounted using a butterfly dowel, which opens when fixed with a self-tapping screw and can be either metal or plastic.

Dowel "butterfly"

Stages of mounting a chandelier on a hook

When thinking about how to fix a chandelier to a ceiling with a hook already installed, first of all check it for strength: hang a load of the same weight as the lamp you have chosen, or pull hard. An unreliable hook that falls out or wobbles needs to be replaced. It is important to remember that fasteners for heavy chandeliers are mounted only on the main ceiling, since no variety suspended drywall can't handle such a load. To mount the collet, a hole is drilled with a puncher, into which the fastener is inserted. A pin is screwed into the collet, on which an anchor hook is hung, or it is screwed directly into the collet.

Mounting the collet on the ceiling

A hole in drywall is also needed for driving a metal anchor into a concrete base or screwing a self-tapping hook into wooden base. To overcome the distance separating the base ceiling from the suspended one, a chain is used: it is hung on a hook and the chandelier itself is attached to it.

As for light fixtures that are mounted on plasterboard ceiling profiles, the fastening is carried out as follows: a “butterfly” hook is inserted into the hole in the plasterboard, which corresponds to the hole in the ceiling frame profile, which automatically opens and locks.

The principle of "opening" and adopting a T-shape also applies to dowels-"butterflies" on which console lamps are mounted. At least two such dowels are needed. They are inserted into the holes in the ceiling and profile and fixed with a self-tapping screw, after which they are automatically fixed.

Butterfly Hook Mounting

Mounting plate installation

These fasteners are mounted on plasterboard ceiling not designed for heavy loads. Therefore, in order not to damage it, you need to strengthen the part of the coating where the lamp will hang. Even at the frame installation stage, you should decide how to attach the chandelier to the ceiling, and use one of the reinforcement options. For example, you can install two parallel profiles (at the same distance from each other as the holes in the plank) or build a square or rectangle out of them (again, in accordance with the dimensions of the chandelier fixture).

First you need to correctly mark the places for the holes in the ceiling: they must match the places for the screws on the bar. Dowels are inserted into the ceiling holes, to which the bar is screwed. In addition, there may be a hook in the ceiling that you do not need, but you should not dismantle it: in case of changing the chandelier, it may still come in handy. The lamp itself is attached to the bar with screws.

Fixing strap for chandelier

There is also a very simple option that can be used for light chandeliers. small size. It consists in fastening the strip to the profiles with long self-tapping screws. For heavier structures, as already mentioned, it is possible to mount only on the main ceiling, concrete or wood.

So how do you hang a chandelier from the ceiling? First you need to evaluate the lamp itself: its weight, type of attachment, size. And this must be done before installation. false ceiling so that it is possible, if necessary, to install the necessary reinforcing structures.

Then the necessary preparatory work, the type of fastening material is determined and the installation is carried out sequentially. When the fasteners are installed, you can connect the lamp to the mains.

Finishing renovations or moving to new apartment, many inexperienced builders are wondering: a how to hang a chandelier on the ceiling? Let's make a reservation right away that it is difficult only at first glance. But after mastering the initial skills of fixing the chandelier, the problems will disappear on their own.

Note! Of course, you can always go to the housing office and call an electrician to your house who will do everything for you, but this option is definitely not ours (we do everything with our own hands!), Especially in such a simple matter.

The electrical aspect of the issue

You most likely saw a hole in the ceiling from which wires stick out (usually three - two phases and one zero). First, determine "xy from xy", for which take an induction screwdriver and touch the wires in turn. And if the light in the screwdriver lights up, then the cable is phase, and if not, then, accordingly, zero.

Note! Touch only the bare part of the wire with a screwdriver, and in the absence of such, strip it after de-energizing it (using a switch or shield in the entrance).

Then do the same with the chandelier - determine by ringing or “by eye” all the wires. If there are several lamps in the chandelier, then put the switch on two keys and make sure that when one button is pressed, only part of the bulbs are lit, and when the second is pressed, the entire chandelier is lit. This can be done by a special connection of wires using terminal blocks, shown in more detail in the diagram.

Video - Correct connection of the chandelier

Having decided on the wires, you can hang the chandelier: zero to zero, phase to phase.

How to hang a chandelier?

Now that everything is clear with the "electric" issue, you can hang the chandelier. This can be done in one of two ways - on a hook or on a decorative bar. Let's talk about each method.

Hanging a chandelier on a hook

Take and drill a small hole in the ceiling. If there is such a hole, simply insert a plastic dowel there and screw in a pre-prepared hook. Connect the wires, wrap the connection points with insulating tape, cover everything with a decorative “cup” (it should be included) and make a test switch on.

We hang a chandelier on a decorative bar

To hang the chandelier in this way, you again need a puncher. First, attach the bar to the place of the planned fastening and mark the places for the holes. Make holes of the appropriate diameter, insert plastic dowels there (only be sure to be corrugated!).

At the next stage, take self-tapping screws or screws and use them to fasten a decorative strip to the ceiling. As in previous version, connect the pre-prepared wires, fix the chandelier and cover everything with a decorative “cup”.

Video - Installing a chandelier

This is the end of the lesson, now you know how to hang a chandelier right and what it takes. And remember about safety. Successful work!

How to choose the right chandelier
How to choose geyser
How to apply liquid wallpaper on the wall?

When buying new lighting fixtures many are wondering: how to hang a chandelier on a concrete ceiling? Indeed, the floor slab, as a rule, has a high density and hardness, which makes it difficult to screw in hooks or bolts. And it is for this reason that many prefer to seek help from a master, rather than doing the work on their own. But in fact, there is nothing particularly complicated in such electrical works ah no - even without experience with an electrician, you can easily cope with this task if you follow our tips and instructions.

Basic ways

To begin with, let's figure out what are the possibilities for installation on the ceiling. Today there are two types of fasteners:

• Hook- used for old-style chandeliers, as well as very heavy fixtures
• Mounting bar or bracket- modern fasteners, which are used for light chandeliers and lamps

The specified types of fastening involve working with concrete slab. Because without special tools not enough. Next - details on how to attach the chandelier in the above ways.

How to attach a mounting plate

The most convenient method of installation on concrete ceilings is the bracket. This is easy, as all the necessary accessories and fixtures are usually supplied with the chandelier. The first step is to install a special bar. This is done in several steps:

- Choose and prepare a place for installation. Since the bracket must fit snugly against the ceiling, the mounting location must be leveled if necessary. To do this, use the usual putty in the color of the decor.

Before hanging the chandelier, also it is necessary to check the wiring, the quality of the output wires- after fixing the bar, it will be problematic to do this

- If there is already a hook in place for mounting the luminaire, then you just need to gently bend it to the ceiling or even cut it down. The second option is more time-consuming, because it is rarely used even by professional electricians.

- We mark the surface. To do this, a bracket is applied so that its edges lie against the surface.

- The marked surface is drilled with a drill with drill for concrete or perforator

- Dowels are driven into the holes, after which the bar is applied and screwed with the screws or self-tapping screws offered or chosen by you

Done, you have installed the mounting plate for your chandelier. Before further work fastening should be checked.

How to connect wiring

The next stage of fastening to the mounting plate is the wiring connection. It is also quite simple to do this work, following the instructions:

• We turn off the electricity in the apartment- this is required by the basic rules of electrical safety
• We are looking at wiring. As a rule, two or three wires are output for mounting the chandelier - phase, zero and, possibly, ground. The number of wires will depend on the age of your home and the wiring itself. Usually, ground wires were not provided in Soviet skyscrapers. But in private homes, on the contrary, this is an almost mandatory element.
• We match the wires of the chandelier. The phase is usually in a red or black shell (again, depending on the age of the wiring), zero is in a blue shell, and ground is in yellow. You can also just test the wires with an indicator. To do this, electricity is turned on in the house, and the master touches the wires in turn. The indicator light will report that there is current in the wire, which means that this is a phase
• Identical wires should be connected with special terminals. In their absence, twist and insulate with ordinary electrical tape or special accessories. If there is no ground wire in the ceiling, the corresponding wire is simply isolated and no longer touched

Fixture fixture

• We attach the decorative element to the bracket and make sure there are no gaps
• We twist the screws or nuts, tightly fixing the decorative trim

That's it - it's time to assemble the chandelier - screw in the light bulbs, hang the shades, etc.

Chandelier hook

More difficult task- installation of a chandelier on concrete ceilings on special hooks. To begin with, let's make a reservation that the hooks are as follows:

• With normal thread
• With anchor bolt

A threaded hook is used for mounting lightweight chandeliers (3-4 kilograms) - only in this case the fasteners can do the job well. For heavy fixtures weighing more than five kilograms, hooks on anchor bolts are used.

Installing the chandelier hook

In the case of threaded fasteners, the algorithm of operation is quite simple. You drill a hole in the concrete where the chandelier is to be installed. A strong dowel is inserted into this hole, into which the hook is subsequently simply screwed.

With anchor bolts, things are a little more complicated, but if you have worked with anchor mechanisms before, then there should be no difficulty. To do this, a hole of the required diameter is drilled in the concrete ceiling. After that, the anchor is inserted there and screwed up to the stop. The peculiarity of this fastener is high reliability. The anchor hook is perfect solution under heavy load.

Connecting chandelier wires to house wiring

The algorithm for working with the electrician remains the same as when installing the chandelier on the mounting bracket. We note several features:

• With a two-phase connection, the steps will be identical, however, you must connect each phase pair in series. If you do not understand electrics and do not have the opportunity to check the voltage, then it is better to leave installation work specialists
• The metal hook itself is best insulated to prevent short circuits for your own safety. This can be done using a special rubber cover or ordinary electrical tape. Make sure there are no open spaces

Hook fastening

To fix the chandelier on the ceiling, follow a few simple steps:

• We hang the chandelier on the principle of "hook and loop"
• We push a special decorative bowl onto the junction of the wires
• Make sure that the bowl fits snugly against the ceiling surface without gaps. This is an optional requirement, but this way the chandeliers look more aesthetically pleasing.

In any case, anchoring will be more reliable and effective - a chandelier installed in this way can be used for years.

How to connect a chandelier with a cascade switch

Such a way - perfect solution for large rooms in which it is customary to install multi-track chandeliers. In this case, the lamps are powered not from one, but from several switches, each of which is responsible for a certain combination of light sources. In this case, not two, but three cores are used. One of them will be common to all horns, and the other two will be responsible for their combinations of light bulbs. To learn more about this, you can explore the options electrical circuits which are easy to find on the web.

Some useful tips for hanging any chandelier on a concrete ceiling

Our tips will help you install the chandelier on a concrete base faster and more efficiently:

Before starting installation, it is necessary to remove everything from the chandelier decorative elements and unscrew all the bulbs. This will protect you in the process of work, and the chandelier itself will not break. It is especially important to unscrew the economy light bulbs, as they contain mercury, which will enter the room if the lamp is damaged.

When checking the wiring wires, it is necessary not only to turn on the light on switchboard, but do not forget to use the switch in the room, otherwise your work will not show any result - you simply will not be able to check the chandelier and wires when studying the wiring. However, before starting the connection, turn off the plugs again

Be sure to calculate the length of the hook before you start installing it - it is important that the decorative cap completely covers the mount. If you see that you have chosen the wrong dimensions after the installation work has been completed, you will have to cut the metal with a grinder or a hacksaw, and then bend the hook with pliers - not every master can do this job. It is best to take into account the features of your chandelier in advance

If you need to lead a heavy chandelier, then you should use anchor fastening. It is also best not to do the work yourself, but to use the help of a partner.

When installing anchor hook for a chandelier, it is recommended to carefully compare its diameter with the diameter of the hole so that you can screw it tightly

Use special electric screwdrivers to work on installing the chandelier, which will signal if current is supplied through the wire. This will simplify and speed up your work and protect you from surprises when installing the chandelier.

If during the test of the chandelier some bulbs do not work or the device does not produce light at all, most likely an error was made during installation. Most often, this means that you have confused the ground wire with the phase. You can fix the problem only by reconnecting the chandelier, as a rule, it is enough to swap two wires

electrical safety

The job of installing a chandelier is not the most simple task, although upon closer examination, no particular difficult decisions not required. However, it should be understood that connecting a chandelier is work with an electrician, therefore it is important to follow the basic precautions:

• Before you start working with the chandelier, you must turn off the plugs
• It is recommended to use only special screwdrivers for working with electricity - with insulated handles
• Chandelier and wires should not be touched with wet hands.
• Before drilling a hole for a hook or dowels, you should check the ceiling with a special device that will tell you where the wires lie. This is especially true if the wiring in the house is old and you did not install it. Often, former owners save money and lay wires, including for a chandelier, without a specific scheme. Damage to the braid during drilling can lead to a short circuit
• When working with an electrician, you should not neglect the safety rules, even if you turn off the power supply - use rubber mats or shoes with rubber soles. This will save you from electric shock if something goes wrong.
• You should not mount the chandelier yourself if you are not sure of the quality of your wiring. The specialist has special equipment for electrical work, and home master it's usually not there

Subject to safety rules and strict adherence to the instructions, fastening the chandelier to concrete base will not take you much time and will be successful and safe. In some cases, for example, with old wiring, the inability to see the wiring diagram, without necessary tool It is best to entrust the work to a professional. Although often completely ignorant of electricians, people do an excellent job of installing a chandelier.

Each owner is well aware that the choice of ways to illuminate the premises allows you to give efficient view room, emphasize the individual preferences of the owner, create a favorable atmosphere in the home.

The original ways of lighting the apartment characterize the image of the owner as a person with a design taste, able to form guests positive emotions, good mood.

Being independently engaged in design, the master uses different kinds fixtures:

1. chandeliers;
2. point sources of local lighting;
3. decorative lighting strips and garlands.

Features of fastening the first two types of lighting fixtures are disclosed in this article. For attaching sconces and garlands, they are also well suited.

How to install a chandelier on the ceiling

Before starting any work on the wiring, always check on it. This will eliminate the possibility of creating short circuits, keep your health, ensure safety at work.

The method of installation depends on many factors. His choice is influenced by:

• weight, dimensions and design of the lamp;
• material and type of ceiling;
• the presence of fasteners mounted during construction.

Fixing a chandelier to a concrete ceiling

Almost all apartments inside multi-storey buildings now have ceilings made of reinforced concrete slabs overlap. During their installation, builders install special hooks or remove the steel wire tied to the reinforcement.

Old-fashioned way to hang a chandelier

In houses old building most commonly used is a mounting wire that can be bent in the desired direction. It is able to withstand quite a lot of weight, but, to check the strength of the fastening, it is recommended to pull it with a certain force.

It is convenient to place light plastic chandeliers on such fasteners. For connection electrical wires use an adapter terminal block.

The fastening element of the chandelier and the connecting wires are hidden inside the decorative cover.

Modern fastening methods

Chandelier hooks

The main element that perceives the mechanical loads of the chandelier is the hook, which can have a different design.

For fastening inside reinforced concrete ceilings, hooks are produced:

1. equipped at the opposite end with a threaded self-tapping screw screwed into a plastic dowel fixed in a drilled hole;
2. having rotary mechanism with stops.

The second method can be used:

• movable paws with a locking mechanism;
• washer with or without a slit;
• rotary plate;
• movable stops.

This method requires the creation of a through hole through the floor slab with a diameter that allows the passage of the rotary mechanism, but securely holds total weight lamp.

Varieties of such hooks are fasteners made in the form of plates that can be pushed into flat slots drilled with thin drills.

Mounting brackets

These mounting fixtures do not require any through holes in the plate. For them, it is enough to knock out sockets for installing dowels with a puncher in the ceiling and then screw the screws through the bracket.

The mounting plate itself can be made:

1. the shape of the plate with slots for fixing in different convenient places;
2. or in the form of a crosshair of two plates.

In the second way, you can create more places for fixing screws in the ceiling. Therefore, heavier chandeliers are attached to the cross plate.

Threaded studs are screwed onto all these brackets before they are mounted on the ceiling to secure the base of the chandelier body with screw nuts.

Before installing the lamp, pay attention to the state of the dielectric layer of the wires. When it is weakened, it is strengthened by winding insulating tape. However, now there are more effective ones on the market. heat shrink tubing which are easily put on the place to be insulated and then under the heat of the flame industrial hair dryer, lighters or even matches are firmly deposited on the surfaces to be joined.

Fixing a chandelier to a wooden ceiling

Here, the main means of fastening are the simplest hooks, made at the end with a sharp self-tapping screw, which is simply screwed into the wood.

So that the wood does not crack, and the screw is screwed in without undue effort, it is recommended to pre-drill the hole with a drill bit smaller than the inner diameter of the thread on the self-tapping screw.

The place of fastening must be chosen so that the hook is held not only in the boards with which the ceiling is sheathed, but also with a significant part of it securely enters the beam.

Fixing a chandelier through a suspended structure

Now home masters in the interior of rooms widely use various types of stretch ceilings:

• on a film and cloth basis from synthetic fabrics of various colors:
• suspended structure based on drywall and similar dense materials.

Realization of the desire of the owner to have beautiful chandelier to illuminate such a room, it requires the creation of a mounting adapter, the thickness of which is chosen according to the size of the gap between the canvas of the suspended structure and the concrete base.

The adapter itself is attached to the concrete in advance, before the installation of the suspended canvas, and then mounted decorative ceiling and already through it a chandelier is hung on the mounting adapter.

Through the drywall coating, you can simply screw in the screws. When used stretch ceiling, then adapters with glued rings are mounted in them, inside which an incision is made in the fabric of the canvas.

Wires are pulled through this slot and the chandelier suspension unit is mounted on the adapter.

Luminaire suspension fixtures

After the hook for hanging the chandelier is installed, you will need to raise the lighting device to the ceiling and connect it at a height electric wires. Such work requires the simultaneous execution of two actions:

• secure fixation of the lamp on the ceiling;
• wiring installation.

Therefore, the master does not have enough hands and an assistant is required. For frequent execution similar work, you can make a simple fixture, consisting of:

• hook for hanging the chandelier for fixing the ceiling;
• cable made of dielectric material;
• tip with a swivel mechanism inserted into the hole of the lamp.

The principle of its work is explained by pictures.

The swivel mount works on the same principle as the fisherman's cuckoo. It is inserted into any hole on the body, and the chandelier hangs freely on a cable. The master has free hands, can connect the wiring. When the swivel mechanism is disengaged, the hook is removed and a lamp is hung in its place.

Such a device facilitates installation. It is made for constant work of the same type. But, when a single installation of a chandelier is performed, it can simply be tied with a strong cord.

How to mount a spotlight on a false ceiling

Drywall constructions

This material has fairly good strength and is produced in sheets with different thickness. Directly in drywall, it is customary to install Spotlights.

To do this, perform work in the following order:

1. wiring is mounted on the base ceiling with a small margin in length to connect the cartridge;
2. install a drywall construction;
3. special drills drill holes for the lamp;
4. wires out;
5. connect the cartridge;
6. compress the mounting plates;
7. the lamp is inserted into the hole until the springs are released to fix the housing.

A protective decorative cover closes the cut hole in the plasterboard.

Stretch ceiling

For fixing spotlights, the same principle is used as for a chandelier - the use of an additional mounting adapter.

Usually they are made at the factory with the ability to adjust the height of the gap between stretched cloth and base surface. For this purpose, the stationary part is attached to the main ceiling, and the position of the adjusting brackets is set with screw clamps.

A fastening ring is also glued onto the fabric of the canvas, as for a chandelier, and a cut is made inside it to pull the wires and install the lamp. Between the light source body and tension material have a transparent protective thermal ring that provides thermal protection of the material.

Constructions from PVC boards

In these ceilings, the installation of spotlights is carried out using the same technology as for plasterboard slabs. PVC boards have good strength characteristics and are able to securely hold light spotlights.

Due to the fact that when replacing burnt out light bulbs, increased mechanical loads can be created, mounting adapters are also used for fastening. They are conveniently made from perforated tin strips with a galvanized surface.

Such structures are easy to create, withstand loads well, and are designed for long-term operation.

After fixing the chandelier to the ceiling, wires must be connected to it and the switch. This topic is presented

We offer you to watch a video on installing a chandelier.

If you know other ways of fixing lamps, then tell us about them in the comments.

Traditionally, it is believed that connecting a chandelier is a difficult task that a professional electrician should perform. But, there is nothing difficult in connecting two or four wires, so any man can hang new chandelier in your home with your own hands.

Connecting a chandelier in a new home

If it's just built a private house, and if it is self-built, then it all starts with wiring. Usually, it is made internal. Although, you can use external wiring, which is retracted into a decorative casing.

Internal wiring

In concrete, brick or wooden wall a special groove is made for electrical wires. This groove is called a groove. You can make it or special device, a wall chaser, or an ordinary chisel. In case of wooden wall- chisel. The same groove is made in the ceiling.

Creating a channel for wires

The wire is placed in a special casing, which is closed from above during interior decoration premises. Don't forget about junction box, from which the wires should diverge to the chandelier, to other lamps, to the socket and to the switch.

Junction box

The presence of a junction box will facilitate the replacement of the fragment electrical wiring if necessary.

External wiring

The principle of laying external wiring is the same, with the only difference being that the strobe is not made, and the wire is fixed directly on the wall in an insulating decorative casing.

Wires in an insulating casing are hidden in the wall

If the switch is single-key, then two wires go from it to the chandelier. And if two-key - then four. Usually, pairs of wires in the chandelier itself different color so there are no connectivity issues.

Connection diagram of a single-gang switch

When conducting wiring, it must be borne in mind that to connect the chandelier, it is necessary to leave sufficiently long ends. This will make it easier to connect. Surplus can always be hidden either in a hole in the wall, or behind decorative cover chandeliers.

Chandelier mounting types

There are chandeliers that are quite heavy. And the safety of people under it depends on how well it is fixed. How it will be attached must be decided by looking at the fastening provided by the manufacturer. Usually, it is of two types:

• fastening with a strap;
• fastening with a hook.

How to hang a chandelier with a plank

Almost all modern chandeliers are attached with a strap. It is a strip of metal, which is fixed to the ceiling with self-tapping screws. To make the fastening secure, you need to drill two holes in the ceiling. Plastic chopsticks are hammered into the holes, to which the bar is attached with screws. Self-tapping screws, entering the chopiks, expand them, which makes such fastening even more reliable.

Photo: fixing a chandelier with a strap

After the bar is fixed on the ceiling, it is necessary to connect the wires to the chandelier. Here it is better to use the services of an assistant who will hold the product. Although, you can temporarily hang the chandelier at some distance from the ceiling with a strong and thin nylon rope. And after connecting the wires, hang it the way it should hang. In this case, one person can do all the work.

You should always use a ladder for this kind of work. No need to stack stools, tables, etc. This is dangerous for your health.

Wire connections may vary. On modern products, special couplings are sometimes made at the ends of the wires. Wires that come out of the ceiling are inserted into these sleeves and secured with a bolt. If there are no couplings, then the ends of the wiring and the wires of the chandelier are simply twisted together. They just twist. You can not connect the wires simply by making hooks at their ends, since the connection must be strong.

Photo: wire connections using a terminal block

Everything is insulated with high-quality insulating tape. If the wires are copper, consisting of many strands, then before connecting, all the strands must be twisted together. Of course, the ends of the wires must first be cleaned of insulation.

On the modern chandeliers at the ends of the wires there are special couplings for connection: just press the spring with a button or lever, insert the wire and that's it!

After the wires are fastened and insulated, you need to lift the chandelier and hang it on the bar. Usually, this does not cause any difficulties. Each chandelier has a decorative casing with which you can close the ends of the wires. This work is facilitated when, during gating, in the place where the chandelier will hang, provide an additional recess.

How to hang a chandelier on a hook

If fastening to the bar is not provided, then a hole is drilled in the ceiling, a plastic chop is driven into it, and a hook is screwed into it. Usually the key is equipped with a special latch that is driven into drilled hole and then screwing expands the spacer. concrete ceiling drilled with a Pobedite drill to a depth of about 7-8 cm.