Make a closet in the hallway with your own hands drawings. Sliding wardrobe for the hallway: self-assembly

Today, more and more owners are paying attention modern design premises. It is extremely important that all rooms are decorated in a stylish, original way and at the same time harmonize with each other. The entrance hall is the place that first introduces guests to the apartment. It has many features. It is in the corridor that they store shoes and clothes, meet guests, preen themselves immediately before going out. It should be practical and comfortable. Installation of the hallway can be done independently.

Today, many are trying to Beautiful design not only in living rooms, but also in the hallway. Thanks to this, the corridor can look stylish, neat and beautiful. But for this you need to know the techniques and methods that will help you correctly arrange the furniture.

It is important to decide in advance on the pieces of furniture that will be located in the corridor. They must be practical first and foremost.

Our climate is very changeable. Therefore, the hallway is often a concentration of dust, moisture and dirt. It is important to think over the floor finish, as well as storage methods. outerwear and rooms. It is important to remember the main rule that the material should be of high quality and durable.

What to put in the hallway:

• Swing wardrobe;
• Shelf for shoes;
• Large mirror.

When choosing this or sometimes type of furniture, it is important to pay attention to its capacity. Very often, overall-looking furniture cannot accommodate a sufficient number of things. Furniture should be ergonomic. Today, modular designs are very popular.

Hallway Assembly: Basic Elements

The cost of arranging a hallway can vary. After purchasing the necessary furniture, the owners will have to resolve the issue of its assembly. This can be done by specially hired workers.

Assembly of the hallway can be done independently. However, this requires certain knowledge and skills.

Furniture can not only be assembled, but also made independently. To do this, you need to determine the number necessary elements. Work should begin with the development of an assembly scheme.

Hallway assembly elements:

• Single cabinet;
• Double cabinet;
• Hanger;
• Pencil case;
• Cupboard.

In order to collect full set furniture, it is necessary to prepare materials, make drawings, determine the number of parts. After the parts are ready, you need to make sure that you have enough fasteners. It is important to assemble following safety precautions.

How to assemble a hallway with your own hands: assembling a pencil case

Pencil size can vary. It is worth deciding on the dimensions of the furniture in advance so that unforeseen situations do not occur. Materials for the pencil case can be bought at building supermarkets or ordered online.

Preparing for the assembly of the pencil case takes little time. The main thing is to cut the planks of the appropriate size.

During the assembly process, the strips must be placed parallel to each other and fastened to the lid with self-tapping screws. It is necessary not to forget to fix the frame with corners made of plywood. After that, it is fashionable to start cutting out doors and shelves.

Features of the assembly of the pencil case:

• May have different sizes.
• The cover should be cut "overlap".
• To fix the doors use 2 or 3 hinges.

The assembly of the pencil case is not difficult. However, you should not take up work without experience working with building materials. It is important that the hallway looks beautiful.

In our next article you will find useful advice by choice of functional wardrobe cabinets: .

Hallway Assembly Scheme: Corner Option

When assembling a corner hallway with your own hands, it is important to be extremely careful. Incorrect calculations can lead to damage to the material from which the furniture is made. Before assembling furniture, you need to check the condition of the wall near which the furniture will be located.

The curved wall suggests the presence of a common frame, to which the shelves are screwed during the assembly process.

The correctness of the assembly scheme is influenced by the size of the room, the length of the walls and the proximity of the doorways. After the dimensions are taken into account, it is necessary to consider the internal equipment furniture design. It consists of six main body elements.

Corner cabinet assembly process:

• Frame assembly;
• Work on the slats (lower and upper);
• Production of back walls;
• Creation of side walls;
• Installation of internal shelves, drawers and baskets;
• Fastening rods and hooks.

Collect corner cupboard you can on your own. For this, it is important to prepare in advance. Watch video tutorials that will help you understand the assembly process in more detail. It is important to note that the quality of the cabinet will depend on the material chosen. It is best to use natural tree species. However, such a cabinet, even with self-manufacturing, will be quite expensive.

How to assemble a hallway with your own hands (video)

You can assemble the furniture in the hallway yourself. The main thing is to take the assembly and installation of the hallway responsibly and carefully. Many designers advise to install a modular design in the living room. It is ergonomic and has a beautiful appearance. Building modules may take some time. Furniture can also be made independently. However, this cannot be done without professionalism and appropriate skills.

Housing furnishing is the final step that combines all the repair and design stages. IN modern furniture several important qualities should be combined: operational functionality, appearance as such, compliance with the general design idea.

Coupe systems or their elements are present in almost every home. The convenience and functionality of this furniture are indisputable, and for such design styles, like minimalism, urban, hi-tech and completely irreplaceable. The article provides comprehensive recommendations for the independent manufacture of a sliding wardrobe.

Advantages

Having considered the pros and cons of this class of furniture, we will get a complete picture of modern concept closet with compartment door opening system.

Advantages
Ergonomics	Standard designs require blind areas for opening. In coupe systems, doors move in the same plane along the guides when opening and closing. Significantly saves floor space.
capacity	The ability to arbitrarily configure the internal space (filling), which determines the spaciousness. The only requirement is ergonomic expediency.
Versatility	Fits into any interior. Various ways decorations and finishes allow you to install the wardrobe in the bedroom, kitchen, living room, etc.
Functionality	Inside, unlike conventional cabinets, you can store dimensional items, household appliances. Embed various devices - ironing board, workbench, countertop, etc.
Ideal solution for narrow spaces	For narrow aisles and corridors, a sliding wardrobe is often only decision. Only it can be put in such places and comfortably operated.
Zoning	Double functional purpose. Using such furniture, you can easily zone the room, that is, it can also perform the function of a partition.
Variety of designs	No restrictions for internal filling. A large number of materials for the manufacture of facades, which allows you to realize any design idea.
Using a mirror	A mirror can be installed on the facade. This will improve the functionality of the room and visually expand the space.
Operational reliability	Doors that move along rails will last much longer than those that open on hinges.

The disadvantages are much less, but they are:

disadvantages
Failure sliding system	Occurs only in the case of the acquisition of a low-quality sliding system.
The need for additional lighting	If the dimensions are large, additional light will be required, it significantly increases operational comfort.
The need to clean the guides	Over time, the lower guides become clogged, which can become an obstacle to the movement of the roller. Therefore, sometimes you have to clean the grooves of the guides.
Mirror gets dirty quickly	If a mirror is used in the decoration, then it will often have to be washed from stains and traces of hands.
No swap option	When designing, the dimensions are related to the specific location of the cabinet. Not suitable for fans of frequent permutations.

Varieties in form

There are several varieties, they have structural and external differences:

• built-in;
• stand-alone;
• corner;
• diagonal corners.

Let's consider each of them separately.

built-in

When constructing such a cabinet, there is no top, back wall and base. Partitions are made only. The entire structure is screwed directly to the ceiling, walls and floor. Metal corners are used as fixation.

This fixed structure, and it is an invariable part of the created interior.

Standing separately

It has sidewalls, top, bottom, back and sliding doors. This is a complete separate subject furnishings. It can be moved, it is not attached to any design elements.

Angular

Great solution for small apartments where every meter is precious. Repeats the shape of the corner and allows you to rationally use the space of the room.

diagonal corner

This is a kind of corner, but the facade does not repeat the shape of the corner, but is made diagonal. The increased capacity of this design determines its frequent use as a dressing room.

Material used

Furniture with a sliding door system is made from a variety of materials. The table shows the main ones:

Material
	The most common and frequently used. chipboard, having a low price, is characterized by sufficient strength. A huge selection of textures, colors, patterns allows you to make a front part for any design solutions. There is one, but significant, drawback - it is difficult to fine-tune. For this reason, mostly simple structures are made from chipboard or chipboard.
	Eco-friendly material, easy to process. The variety of facade coatings is no less than that of chipboard. Practical and affordable material.
	Expensive option but natural wood will last a long time. A great decoration for any interior.

Types by design

Classification by design differences is as follows:

1. embedded;
2. case.

Embedded . There is no need for top, bottom and side parts. Their function is performed by the walls, floor and ceiling of the niche. For the manufacture, you can use drywall, which will reduce total costs on the product.

Cabinet . The main difference from conventional cabinet- method of opening doors. If necessary, you can move. Transportation (moving) without disassembly is possible. Minus - increased consumption of materials, as side, lower and upper walls, the back are made.

Now let's take a closer look at the organization of the internal volume of the cabinet.

Design features

When designing, ergonomic and operational specifics should be taken into account.

Consider the main structural elements sliding wardrobe.

Door width

The choice of door size depends on factors:

• manufacturers of sliding systems are limited to certain sizes. Some systems allow you to make a sash up to 120 cm wide;
• the width is affected by the number of internal sections. Each section must be freely accessible;
• choice is influenced by personal preference. There are no special rules, unless it goes beyond the restrictions listed above.

The optimal width, worked out in practice, is from 600 to 900 mm. This size provides the most comfortable conditions use.

Sliding systems

Sliding systems are classified according to two main criteria:

1. profile material;
2. expansion principle.

For the manufacture of the profile of the movable system, aluminum or steel is used. The material of the sliding system is chosen, as a rule, the same as that used for the door frame. Steel structures are cheaper, but in most cases aluminum is preferred.

Structurally, two types of systems are produced - bottom-support and top-hung. In the lower support - the door with rollers moves along the rail. In top-hung - its rollers move along the upper guides.

Height

The height is chosen arbitrary. The only limitation may be the ceilings or the small stature of the owners of the apartment / house. Designs are made both from ceiling to floor, and smaller heights.

The standard length of wall material used is 270 cm. Standard apartment has a ceiling height of 260–270 cm. Almost identical dimensions allow you not to saw or build up structural elements.

For ceilings above 270mm (if you want a floor-to-ceiling cabinet), there are two solutions. First, the sheets of material are joined to the required length. The second - the mezzanine is going. Sheets can be joined on high-precision equipment of companies specializing in such services.

Shelf depth

The depth of the shelves determines the daily usability of the cabinet. The optimal and recommended figure is 60–70 cm. Usually a hanger bar is placed in the closet, the width of which is about 48 cm. A depth of 60 cm will completely eliminate the contact of the inner surface of the door and the clothes hung on the hangers. Most furniture accessories (boxes, trays, etc.) have a width of 50 cm. You should not make shelves deeper, since it will be inconvenient to get "under the wall" when placing things.

Not always the dimensions of the premises allow you to install furniture with the maximum recommended depth of the shelves. But there are limitations on the minimum depth. The best option may be a depth of 40 cm. Considering that 10 cm goes under the mechanism sliding doors, small hangers 30 cm wide can be purchased. Alternatively, mounting a hanging bar (s) perpendicular to the doors and the back wall, in this case, the width of the placed hangers is not limited.

Such a solution is much better than completely refusing to install a cabinet, especially since even such a "narrow" design for small apartments - perfect solution.

Length

When designing, the length of the cabinet is selected in accordance with the place of its further installation.

Height of shelves and rods

The height between the shelves is 250–350 mm. The choice rule is simple: more depth of shelves - more distance between them, less depth - less distance. This dependence is associated with the convenience of access to the stacks of linen located in the depth of the shelf (near the back wall).

When designing a mezzanine, you should take into account the dimensions of things that are supposed to be stored on it. If these are suitcases, then the height of the mezzanine should be equal to the height of the suitcase, plus a small margin.

The mounting height of the hanger bar is determined by the length of the clothes placed on it. Max Height will be equal to the longest thing. Average length of typical wardrobe items:

• shirts - up to 100 cm;
• jackets - up to 110 cm;
• long clothes - up to 130 cm;
• raincoats and fur coats - up to 150 cm.

These calculations are approximate, since the length of clothing depends on height, style and other parameters.

Video:

Schemes and drawings

The diagrams show various options furniture assembly projects and technologies:

Device inside

When designing the filling of a sliding wardrobe, first of all, zoning of the internal space is done. The figure shows a universal scheme for dividing various things into storage zones:

Buying ready product, you will have to agree with the filling configuration proposed by the manufacturer. Self-manufacturing will allow you to take into account the dimensions, functionality, location of various zones and much more, which, ultimately, will provide maximum operational comfort.

Below is a table with examples of frequently used elements of internal filling and zoning of a sliding wardrobe with their help.

Zoning
	Shelves are one of the main elements of filling. They can be fixed and retractable, solid and ventilated, half and full depth, etc.
	Drawers - the second most important element of the cabinet.
	Hanging bar - necessary for clothes on hangers. The material of manufacture is different, most often metal.
	Convenient storage baskets. All things are clearly visible in them, which creates a certain convenience.
	This device is called - bruchnik. Pants are always ironed and ready to wear.
	Rod (hanger) for storing ties - it is convenient to choose, do not wrinkle, the correct suspension prevents shape change.
	Convenient placement of belts, as an alternative - storage on a shelf in rolls.
	Compact and convenient storage underwear.
	Placement of bed linen, towels, some clothes in piles on shelves.
	For storing blouses, light blazers, short sundresses, a significant part of the internal volume is allocated. A pipe with hangers is installed in the opening. You can make several of these departments - for short and long things.
	Section for accessories - bracelets, watches, glasses, etc. It is recommended to store these items in drawers. Inside the space can be divided into separate cells.
	Shelves for storing shoes. In the upper (mezzanine) part, you can place shoes in boxes.
	Hooks, hangers, carabiners, rings and other accessories for bags.
Hiking suitcases	Rarely used (once a year during the holidays) suitcases place on the far (upper) shelves or mezzanine.
	One of the options for bed linen. Shelf width up to 80 cm, height - up to 60 cm.

Characteristics of the main filling elements:

• sliding and fixed shelves. For convenient use, the distance between them is from 350 to 450 mm;
• drawers. Two types - fully retractable (100%), partially retractable (80%). Can be equipped with closers that provide smooth semi-automatic closing of the drawer;
• mezzanines, known as hard-to-reach shelves. Located at the top. They store rarely used and overall things;
• bars are needed for hangers. Mounted across the width of the cabinet;
• pantographs or special "furniture lifts". Thanks to them, clothes are stored at the required level and can be easily pulled out with a special bar. They are electrical or mechanical;
• baskets are convenient for storing small items. Equipped with rollers and guides.

facades

Thought out to the smallest detail, the internal content will be sharply dissonant with unsuccessfully chosen facades. It is the facades that give the whole cabinet a special finished look. Consider several options for their implementation.

Mirrored

The mirror visually enlarges the space and makes the room brighter. It can be whole or divided into several parts. The large weight of the mirror determines the need to select high-quality and reliable rollers. Such a facade creates additional maintenance chores - the mirror quickly gets dirty. It will have to be wiped and washed regularly, especially if there are small children in the family.

For façade mirrors various finishes- sandblasting patterns and drawings, coating of various shades (silver, emerald, gold, etc.) for glass, printing color images and much more. For safety reasons, the mirror inside covered with anti-shock (armor-) film. If the mirror breaks, the pieces will not scatter.

glass

Glass is no less popular than a mirror, facades are equipped with unbreakable. Mainly used frosted glass with an image. Vertical, horizontal stripes look original, dividing the canvas into separate squares.

MDF and chipboard

These materials are laminated with film. The facades look massive and heavy. To install them, you will need reliable roller systems. One of the advantages is a huge selection of colors, shades and patterns, in texture - from matte to bright glossy.

on MDF and Chipboard facades photo printing can be applied.

These are the main types of facades used in the manufacture of sliding wardrobes. You can combine them with each other. This article contains photographs with a considerable number of original ideas for the production of facades.

Step by step instructions for making

Adhesive edge tape

After cutting all the elements, the edge tape is glued to the ends of the plate. The sequence of operations performed:

Instructions for gluing the edge to the end of the blanks
	If there is no assistant, you can use a simple trick. You will need a small box and a quick clamp. The clamp presses the board to the box, ensuring the stability of the workpiece and the convenience of gluing the edge tape.
	One side of the edge tape has an adhesive surface. Warm up to high temperature it is easy to stick to the workpiece.
	Cut the edge to the desired length. Leave a margin of 1 cm around the edges. You can cut off after gluing with ordinary scissors.
	For gluing, set the position of the temperature sensor of the iron to "2".
	For your safety, wear left hand two gloves. There should be no pellets on the palm.
	Run the iron along the edge tape, and hold it with your left hand (leveling).
	We carry out the iron in the opposite direction, at the same time with a hand in a glove we firmly press (smooth out) the edge tape.
	Hand smooth the edge a few more times.
	The use of a special roller. Glue the edge tape with an iron and then roll it with a roller. Very comfortably.
	The cooled tape, with a sharp knife from the end, carefully cut off the remnants.
	We get such a cut.
	We repeat the procedure for all ends of the workpiece. We measure the tape with a margin of 1 centimeter, from each edge.
	Glue with an iron and smooth.
	We cut off the cooled edge. The edge has already been glued on the adjacent edge, we make the cut very carefully.
	From all sides we cut off the longitudinal remnants of the protruding edge.
	Result. We glue the ends of the remaining blanks with an edge tape.
	All cuts are ground with a special bar. The inner part of it is filled with foam rubber, the outside - fine-grained abrasive.
	Grinding of slices is done only with longitudinal movements.

Processing of the main elements is carried out in a similar way.

Assembly

Details are cut according to the project. This operation is best done in the workshop on a special format machine. After cutting and gluing the edges, we assemble the cabinet:

Frame Assembly Instructions
	To work, you will need to assemble an additional device, consisting of a metal strip and two pieces of board connected at an angle. It turns out a corner with a metal guide. You will also need two quick clamps. With this device it is very convenient to connect workpieces at right angles.
	We make a check with a square - it should be 90˚.
	Set aside 70 mm from the top edge.
	In the example, a 16 mm plate is used, therefore, 9 mm must be retreated from the edge. Why not 8 mm? Because the plate protrudes 1 mm beyond the edge, forming a small ledge. The middle of the end of the adjoining plate is at a distance of 9 mm.
	Drill mark.
	A similar mark is placed below.
	Using a drill, we make holes for fasteners.
	A special drill replaces three at once. It allows you to make the main hole, corbel and chamfer in one operation.
	drilling.
	We twist the confirmation with a screwdriver.
	Having fixed the sidewall, according to the project, we mark the places for installing the shelves.
	Next, using a square, put marks on both sides under the holes for attaching the shelves.
	Marks on which holes for confirmations will be drilled.
	The device assembled at the beginning of work is convenient to use for attaching shelves. We measure with a tape measure 1/2 the thickness of the plate. The thickness of the plate is 16 mm, so we retreat 8 mm from the mark.
	At this level, we install the shelf using quick-clamp clamps.
	It is clearly seen here that the mark is in the middle of the end face of the workpiece. Everything is ready for drilling.
	Drilling.
	We twist the confirmations.
	Install the remaining shelves in the same way.
	Install the crossbar. And we fasten each shelf with confirmations.
	Having fixed the cross member with a quick-clamp clamp, we twist it with confirmations from above and below, then we fix each shelf.
	So going Bottom part sliding wardrobe. We clamp the strip from the plate with a clamp and fix it from the end with a confirmation.
	We drill shallow holes from below for installing furniture legs.
	We twist the metal sleeve with external and internal threads.
	Using a hexagon, tighten (retract) to the desired position.
	We twist the leg with a plastic support into the sleeve. Thanks to this, the furniture can be moved and leveled.
	Two parts supporting leg assembled.
	After assembling the cabinet on its back side a fiberboard sheet is attached with ordinary carnations.
	Fastening fiberboard start from the top. By tilting the cabinet from side to side, we achieve a 90˚ angle between the sidewall and the top bar. We nail the side and bottom sides of the fiberboard sheet.
	When assembling, such plastic furniture corners were not used. Why? The use of confirmat is much more practical, since it is screwed into the slab by several centimeters and securely connects the structure, giving it additional rigidity.
	We close the hats of confirmations with a decorative cap.

In the same operating sequence, you can assemble a sliding wardrobe of any configuration.

Video:

Door manufacturing

The door consists of a frame, metal guides and a system of rollers. It is worth ordering it from a company professionally engaged in similar systems. Specialized software according to the given dimensions, it will calculate all the elements and issue a complete specification for the assembly. Mirrors or slabs of other materials are cut to the size of the doors for mounting in frames.

Elements for sliding system
	Vertical bars/handles for the side parts of the door.
	Sealing rubber for a mirror.
	Self-adhesive brush to soften the impact of doors when they are opened / closed.
	Staples for fixing doors in extreme positions.

The main parts for assembling the doors are made of aluminium. All metal components must be covered protective film to protect them from scratches during transit.

Sliding system assembly

Consider step by step assembly door leaf. In our example, there will be two mirror doors.

Finished closet

Door Assembly Instructions
	The door is located in a horizontal position and provides free access from all sides.
	At the top vertical rack, simultaneously serving as a door handle, we drill two mounting holes.
	The lower one is 6.5 mm in diameter.
	Top hole - 10 mm. Through it, the upper profile of the doors and the roller will be attached.
	lower part of the same vertical profile. Top hole - 10 mm, bottom - 6.5 mm. Distance from the edge of the first hole - 7 mm, the second - 43 mm. Closer to the edge, the lower roller will be attached. The second hole is for the screw connecting to the profile.
Profile mounting	From above we fix the rubber seal with a profile, gently inserting it.
	The procedure is performed sequentially on all faces. Rubber compressor we do not cut off at the corner, but continuously lay around the entire perimeter.
Should not be screwed all the way	This screw is not fully tightened. Later, the upper rollers will be installed in it.
	Install the upper rollers and tighten the screw until it stops.
	Rubber seal installed at the bottom of the door.
The screw with the top roller is also twisted	In the upper part we fix the second pair of rollers.
	Install the bottom roller. We press the spring on the roller and carefully insert it into the hole, fix it with a screw.
	The screw is tightened with a hexagon.	Wardrobe with the first door installed.
	In the same sequence, we assemble and mount the second door.

Additionally, we install auxiliary elements - a pipe for hangers, etc.

Video:

At the end it should look like this

We invite you to familiarize yourself with the diagrams and drawings. They will help you create your own project.

Video:

Video:

A photo

The hallway will be inferior if it does not have a solid spacious closet. It is not necessary to buy it at all, since the manufacturing process is quite simple.

Spacious closet in the hallway niche

The advantages of this option:

• you can choose any project that is most suitable for the hallway in terms of style and parameters;
• designers for development individual project don't have to pay;
• material costs are minimal.

The main thing is that the furniture in the hallway should be roomy, compact, neat, not pretentious.

Details to consider when designing.

• must be exact dimensions;
• the presence of a crossbar to accommodate the hangers;
• hooks for clothes for every day;
• one or more shelves for hats;
• cabinet for storing shoes.
• mirror;
• small drawers for small items (gloves, scarves, etc.).

Furniture fittings for the wardrobe in the hallway

To assemble a wardrobe in the hallway with your own hands, the following tools and accessories are prepared in advance:

• guides for installing boxes;
• tires, if a "coupe" with a sliding system is conceived;
• hinges and handles for doors;
• clothes hooks;
• the number of nails, screws, self-tapping screws calculated in accordance with the project;
• wooden fasteners are also needed: confirmations, dowels for furniture assembly;
• furniture corners (metal, plastic) and plugs;
• you can not do without a standard set of tools (screwdriver, drill, electric jigsaw, saws for wood, a key for furniture confirmations, a mallet, clamps, a square and a building level).

DIY cabinet assembly tool

It is better to take inexpensive materials that are easy to process. For example, even experienced manufacturers will not undertake to make furniture from solid wood.

• Chipboard is the most acceptable option for a future DIY product. This material is easy to cut, process. The building material weighs a little, so it does not need reinforced fasteners or fittings. An important fact is the low cost.

  

  Chipboard cabinet with mirrored door

• Plywood is a light, durable and denser material that can be used to make curly details, as well as welt patterns.

  

  Spacious eco-friendly plywood wardrobe

• MDF can be subjected to various types of processing (painting, tinting, staining, etc.). It is less durable than plywood.

  

  Sliding wardrobe and cabinet made of MDF in the hallway

• Fiberboard must be purchased for the back walls of the elements.

  

  Fiberboard for the back wall of the cabinet in the hallway

• wooden beam for frame structure.

  

  Wooden beam for the frame of a homemade cabinet

• Edged boards(usually from pine).

  

  Edged board (pine)

• Drywall for interior space equipment with built-in niches.

  

  Homemade drywall wardrobe in the hallway

The most responsible approach is to take measurements. If a miscalculation is allowed, all subsequent work will be difficult or nothing will work out at all. There are various ready-made options from suitable sizes. If the finished drawings are not suitable, and the drawing skills are weak, you need to attract a specialist for this stage, who will think over the project with the right dimensions. Cutting materials and edging the end parts is better in a store that sells building material. Store services are inexpensive, but it saves a lot of time.

Assembling the wardrobe

This model belongs to the built-in ones, it is easier to manufacture, since the parts do not need to be calculated and cut out. The complexity of this option is that it is necessary to take into account the features of walls and floors.

The ideal solution for such furniture would be a niche with a sliding system, equipped with several shelves, a crossbar for hangers. The installation of the sashes in this case is the same as for interior doors(involved wall and floor).

Very often, a closet is made in the corner of the room. This model does not have one side and back wall (and in some cases there is no floor and ceiling).

The base consists of wooden frame, which consists of a pair of frames (front and side), assembled on self-tapping screws or nails. If the project provides for the arrangement of shelves and partitions, cross rails must be fixed to the frames in the designated places.

Instruction

Mark the walls, floor, ceiling in places where the frame will be installed, drill holes for the fasteners. It is recommended to mark the places of the paper clip as well.

We make markings for shelves, install corners

Fasten the front frame to the wall and ceiling with dowels. Check its verticality using a level.

We lay and fasten the shelves on the corners, install the vertical panel to the shelves inside the cabinet

Install the side frame.

In the resulting niche, wooden slats are attached to the walls, designed for shelves (cut shelves from plywood or chipboard). You can not fix the shelves by laying them on the slats or fix them with nails.

On top of our construction, we lay a horizontal shelf according to the level

The side is sheathed with drywall or laminated chipboard. Drywall is pasted over or painted. The side part, in which the crossbar with hangers will be located, must be strong (chipboard, plywood, but not drywall).

We prepare panels for the front side of the cabinet

Attaching the bottom and top panels

The final stage is the installation of sliding doors. Top and bottom rails are mounted respectively on the ceiling and on the floor.

Installing door rails

Here it is very important to observe the exact dimensions. First, they try to install the layout of the future door. Take any part whose height is the same as that of the door and install it inside the top rail. Check the verticality value and mark the area where the lower guide will be attached. The door must first be inserted by slightly pressing on the upper rollers, and then into the lower tire. To adjust the position of the door leaf, adjusting screws are used. Right installed door moves smoothly and unhindered.

We insert the doors into the guides, snap the latches and adjust the mechanisms in the roller systems

The above example is suitable for a simple small size structure consisting of two halves. With a good hallway area, it is possible to manufacture a more spacious model. Then the frame of the bars will not work. It is better to make a base from chipboard, and “fasten” its elements with the help of a common floor and ceiling. This method will allow you to place in a niche, in addition to shelves and a bar for hangers, also boxes for small items and other details.

Such a product will be assembled as a designer for dowels and confirmations. For this fitting, you must first drill holes. All this must be done very carefully and patiently. All fasteners for corners are kept in a clamp for a day.

Built-in two-door wardrobe in the hallway

Corner cabinet assembly

It will be easy to make a corner module with your own hands. For stability, modules are often made of durable solid materials (chipboard, plywood). These products come in several forms:

• triangle;
• L-shaped;
• trapeze;
• five-walled.

Basic configurations of corner cabinets

The most suitable for the hallway is five-walled.

Built-in five-wall corner cabinet

Detailed assembly diagram of the corner cabinet

Instructions for self-assembly of a corner cabinet

Shoe cabinet assembly

Convenient do-it-yourself shoe cabinet

This is the easiest process, because everything that is needed in the work is sold by the building materials store.

The design includes: an outer frame, several shelves with partitions. The width of the structure depends on the maximum shoe size, and the height depends on the number of shelves.

Addition of facades and clearances of cabinets for shoes

A good solution would be to connect shoe cabinet with chest of drawers. Or place it in a closet or corner wardrobe, which have open facades.

There is a lot of information on the Internet about how to make a closet in the hallway with your own hands. Therefore, by examining all the available data, the most suitable model can be successfully constructed.

Video: Wardrobe in the hallway, do it yourself

Sliding wardrobes are an excellent solution for rooms with limited space. The doors move apart like on a train, which allows you to install the cabinet in small hallways and narrow corridors. A similar design is offered in all furniture stores, but not always typical dimensions fit exactly the size of your room. You can order a wardrobe designed to your measurements based on the characteristics of your room, but the cost of one copy doubles. For those who need a cabinet larger or smaller than a typical one, there is another solution - to assemble the structure with your own hands. This is not very difficult to do if you know where to start.

photos

Choice of cabinet design and placement options

Placement of the cabinet in a niche. Residential designers are sometimes very inventive, so in half typical houses in the hallway there are niches of unknown purpose. It is in this niche that you can make a wardrobe. To do this, you will need to install door guides and order the doors themselves with fittings. This way you save space, time and money.

Wardrobe along the entire length of the wall. A good solution is to build a cabinet along the entire length of the wall. Firstly, the room is not broken by the corners of the furniture and visually does not lose space. Secondly, such a closet can serve not only as a wardrobe, but also as a pantry where skates, skateboards, skis and even car tires are stored.

A sliding wardrobe can separate the hallway area from the living area in studio apartments. The wardrobe is installed across the entire width of the room, in its center a through compartment door is made, and on the sides there are compartments for clothes. Some prefer to make all the doors on both sides, which provides access to clothes from the hallway and bedroom at the same time. Very convenient option when access to outerwear is carried out from the hallway, and access to bed linen is from the living quarters.

materials

The most optimal for creating a cabinet is chipboard and MDF of high or medium density. This material is not very expensive and relatively dense. But when choosing chipboard, be sure to pay attention to its category (should be E-1) and the coating (preferably laminated on all sides). Chipboard emits formaldehyde and phenol when heated, so if there are heating pipes in your hallway, then don’t risk it and choose another material. Another disadvantage of chipboard can be considered a weak retention of screws.

MDF is safe for humans, because when heated, lignin is released, which is contained in natural wood. True, the price of MDF is significantly higher, and it is a fire hazardous material.

Wood - traditional material, however, if you plan to make a built-in wardrobe, then it is better not to use it. Concrete wall additional moisture is created, and spruce and pine, from which boards are usually made, have low moisture resistance.

It is better not to use drywall, because this material is not for manufacturing. load-bearing structures. He is fragile and if not thought through complex structure bases, will not hold the wardrobe doors.

One of options is the preliminary design of the cabinet, and then the purchase of ready-made components in stores or the creation of such components to order in the workshop (still cheaper than buying ready-made furniture).

What to consider when designing

When you design your own closet, consider the following:

• useless space (this is what takes up space, but is not used for its intended purpose. In a particular case, this is a sliding system. It is necessary to lay 10 cm on it and add to usable space, which must be at least the width of the hanger. Thus, the depth of the wardrobe with a standard bar is: the width of the largest hanger + 10 cm for the convenience of placing things + 10 cm for door mechanism);
• if you are assembling on the floor (do not mount the cabinet in a niche or directly against the wall), then the height of the structure must be at least 10 cm lower than the ceiling height in the hallway at a depth of 70 cm, and preferably even more so that you can lift and put the cabinet vertically;
• if you plan to put the cabinet on adjustable support legs, then lay a place under them next to the nearest partition (no further than 30 cm from it);
• structural rigidity is provided by transverse ribs on the back wall of the cabinet, without them the structure will stagger;
• if space does not allow the installation of a cabinet with a standard longitudinal bar, lay several sections for the transverse bar;
• when designing drawers, allow 7 mm between fronts for the width of the bottom rail protruding downwards. If this is not done, the drawers will not close;

• the most important thing when designing internal sections is to consider the width sliding design! Therefore, decide in advance on the number and width of doors, so that later you can fit the entire system under them. If the width of the door does not match the width of the chest of drawers, the drawers will not open. Bulkheads between compartments must coincide with the boundaries of the doors;
• shelves have a distance of about 30 cm;
• the compartment for hanging clothes is calculated based on the length of the longest thing and another 10 cm is added to it;

In any wardrobe, especially if it is alone in the apartment, there should be sections for storing outerwear, shoes, hats, linen, bed linen, suitcases, pillows, blankets, dresses, jackets and trousers. The picture shows the optimal placement of sections in the closet for the hallway.

Drawings can be made in design programs: "Astro Furniture Designer", "Pro 100", "bCAD" and others.

The entrance hall is the first thing you see when you enter the apartment. Often the choice in stores is the same, and choosing furniture for the corridor is not easy. And if it is not large, then the closet simply may not enter or take up all the space. In this case, you can make furniture for the hallway yourself. In addition to saving money, you will get a customized model that suits your space.

What furniture is needed for the hallway

The main rule for furniture in the hallway, it should be roomy, compact, with a neat appearance. Don't over decorate it. In addition to decoration, it has the function of storing things. You should carefully consider the size, availability of drawers and cabinets. It is better if there are more of them, but it is necessary to push off from the area of ​​\u200b\u200bthe corridor, you do not need to overload.

Hooks of an unusual shape on the wall look beautiful, plus a shoe rack.

Looks original, if available large hallway, wooden bench, it will give the interior a zest. A win-win wardrobe, it will fit into any interior. And a wardrobe, if space permits, is an ideal solution, it is comfortable and roomy.

At small sizes, you should use:

• built-in wardrobes - take up minimal space,
• mirrors and light finishes - visually expand the space.

DIY hallway furniture

With the help of the right project, even a small area can be transformed, and the hallway will look organic and roomy.

The design of this room should be combined with the interior of the entire apartment. It is permissible to choose a different decor or floor covering different from other rooms, but the stylistic direction should be the same.

Practicality

When choosing a model, you should pay attention to practicality. With a small hallway, you should stop at the standard version and choose multifunctional furniture: compartments for clothes, shoes.

A compromise between capacity and external beauty is a corner cabinet. It looks small, but has a lot of depth, so it's roomy.

In the presence of a large family, it is necessary to think over a place for the things of each inhabitant of the apartment.

The entrance hall is a room into which dirt is carried from the street. Therefore, it should not be done in light colors, it will quickly get dirty. And such things as: umbrellas, strollers, bicycles, it is undesirable to carry deep into the apartment, it is worth providing a storage system for them in the corridor.

Individuality

Everything that is done by hand, including furniture, is always the embodiment of your ideas and desires. You can decorate the hallway with decor to your taste and give it personality. Such furniture will be one of a kind, and not mass-produced at the factory, and guests will be surprised at its exclusivity.

What you need to work

Having chosen a model, having made a drawing, you should prepare everything that is needed for work: material, accessories, tools.

Depending on the type of furniture, the accessories need different:

• sliding wardrobe - guides for drawers, tires for a sliding system;
• closet with hinged doors- hinges, handles, locks;
• hooks for clothes.

Instruments

You should stock up on the following tool:

• saw or electric jigsaw;
• screwdriver or screwdriver;
• sandpaper;
• with a knife;
• screws;
• tape measure;
• corners;
• loops;
• plugs;
• special wooden fasteners;
• chimney.

This is the main set that can be useful in the manufacture of furniture.

We make the hallway ourselves: the choice of material

Importance is given to the choice of material, should not be taken too expensive. In addition, it should be easy to process and safe for health.

Suitable: plywood, chipboard, fiberboard, MDF, furniture board, edged board, wooden block, drywall - they have a long service life and good quality.

• Wood. Wood is an environmentally friendly material, so it is perfect for an apartment. It never goes out of fashion, and furniture from it speaks of the wealth and excellent taste of the owners. The wooden entrance hall will harmoniously fit into any style. It can be carved, thereby giving individuality. For the manufacture of furniture, different species are used: oak, birch, pine, beech, walnut. The only negative is the high price, but given the long service life, this cost will fully pay off.
• Furniture shield. Made from natural materials and therefore safe for health. Looks classy and lasts a long time. The cost is high, but below the tree.
• Chipboard. Chipboard is a common and convenient material for making a hallway on your own. It is simply cut and processed, weighs little, there is no need for reinforced fasteners. With all the pluses, it is affordable.
• Plywood .. It has the same qualities as chipboard, but more dense and durable. From it you can make not only parts with curved lines, but also make a welt pattern.
• MDF. Slightly less durable than plywood. But has endless possibilities in processing: painting, toning, staining.
• Fiberboard. It is used only for the manufacture of the back wall of cabinets.
• Wooden bar. Designed to assemble a frame structure.
• Cutting boards. Relatively expensive material, pine boards are the most affordable.
• Drywall. Built-in niches are equipped with drywall.
• Mirror or glass. Glass or mirror inserts will decorate any room, and you can’t do without a mirror in the hallway. However, they are heavy and cannot be handled alone.

Choosing a hallway depending on the type of room

When designing a hallway, you need to take into account the features of the room and the number of households. You should decide on the functional accessories of the hallway so that it is practical and comfortable. With a small area, the beauty of the closet will not be visible and it will look bulky. It is better to choose the corner version of the hallway. In addition, there should be enough shelves and hooks for all family members.

Correct solution- install furniture along a long wall.

Ordinary hallway: instructions, diagrams and drawings

Making a simple entrance hall yourself is not difficult. It includes: a hanger, a shoe rack, a small pencil case or chest of drawers with a mirror.

For this you will need:

• loops;
• furniture board;
• plywood;
• grooved boards;
• three-dimensional rail.;
• pens.

The first thing to start with is a pencil case. For this, planks of the required size are cut out of the shield, a cover for the top (with an overlap) and shelves. The assembly is not complicated - the slats, with the help of self-tapping screws, are attached to the lid, the shelves are installed in the same way. For structural strength, corners are cut out of plywood and fixed in the corners. A door is made from the shield, which is mounted on 3 hinges.

Now we make cabinets. If desired, you can make only one cabinet. For manufacturing, you need 2 sidewalls of the same size and a bottom that will connect them together. The lid should be made smaller than the bottom. All parts are fixed with glue and screws. Doors are cut out of the shield and attached to the hinges. In the presence of drawer skids are required. You can make them yourself from plywood, but it’s better to buy them (the box will roll out easily on them). The second cabinet is made according to the same principle as the first.

Now, the whole structure is going. The prepared boards are fixed to the edge of the pencil case and to the cabinet - this will be the base of the hanger. From above, the boards are connected with a rail, for strength. Hooks for clothes are attached to the rails, and a shelf for hats is screwed on top.

The final stage is the installation of handles and varnishing.

Corner option: instructions, diagrams and drawings

Corner hallway easy to do with your own hands, but in order for it to be stable, it is necessary to use solid material: chipboard, plywood. The module consists of 2 parts that are connected at right angles. In addition, you should decide whether the walls themselves will be the frame or the base. If the walls are even, then you can do without a frame, fasten the shelves directly to the walls - this will be economical.

Manufacturing principle:

• a drawing is made in size, areas for attaching shelves are marked;
• Chipboard is cut with a jigsaw;
• holes are drilled for dowels on the front side of one panel and at the end of the other, holes are made for confirmations;
• dowels are lubricated with glue and sidewalls are assembled;
• shelves are attached to confirmations, clothes hooks.

If necessary, you can attach a mirror to the door or make compartment doors, thereby getting a corner wardrobe.

Do-it-yourself non-standard hallway: drawings and diagrams

If there is a non-standard corridor that does not fit the wardrobe or hallways sold in the store, you can resort to the original and simple solution. For example, the presence of a bedside table or shoe rack, plus a hanger and a mirror.

You should start with a nightstand. From furniture board 2 sidewalls of the same size are cut out, the base and the lid. If there are skirting boards, then the corners are cut off from the sidewalls (on one side). Back wall made from plywood. All parts are fastened with self-tapping screws. Inside, skids for drawers and fasteners for shelves are made. Doors are hinged.

A hanger in the hallway is an element that you cannot do without. It is not difficult to make it and you can give free rein to your imagination. For lovers of eco-style and everything natural, tree branches are suitable instead of a hanger. Those who prefer country style need a vintage version.

Capabilities wardrobe: instructions, diagrams and drawings

The sliding wardrobe is an excellent choice for the hallway, it can be built-in or separate. If there is a niche, shelves are mounted in it and it is equipped with a sliding system.

The process of manufacturing a cabinet with side walls:

1. A wooden frame is being made.
2. The place for the cabinet is determined. Holes are made on the walls, floor, ceiling to fix the frame.
3. The front frame is attached to the wall and ceiling with dowels, and then the side ones.
4. Inside, rails are mounted under the shelves. The shelves themselves are cut out of plywood.
5. The sides are sheathed with drywall, then glued or painted as desired.
6. Guides are mounted on the floor and ceiling.
7. Doors are installed - first in the upper tire, and then in the lower one. Doors must move freely, their position is regulated by screws.

You can make a sliding wardrobe in different sizes and models, depending on the preferences and area of ​​\u200b\u200bthe room.

Furniture for the hallway is really do it yourself. Models are quite simple and small in size. And if you have imagination, you can turn an ordinary hanger into a piece and a unique thing.

Photo gallery

Video