How to attach a sink sink to a countertop. How to choose and install a mortise sink in a countertop: expert advice

Installing a sink in a countertop is a rather laborious and very difficult process. If you do not follow all the installation conditions, you can not only reject an expensive plumbing fixture, but also seriously damage the surface of the countertop. The sink in the kitchen is one of the strategically important objects, therefore, when choosing and self installation it is necessary to listen to the recommendations of professionals on how to embed the sink into the countertop, and do everything clearly according to the rules.

Types of kitchen sinks

Self-assembly kitchen sink can be made taking into account various technologies. It is necessary to choose the type of installation, depending on the type of sink construction:

1. Overhead, perhaps the most budgetary and simple to self-assembly. The sink must be put on a separate cabinet, so here you need to know how to attach the sink to the cabinet. The disadvantage of this option is the gaps that remain between the sink and cabinet.
2. Mortise sinks are mounted directly into the countertop itself, for this you need to cut out the appropriate hole and clearly understand how to cut the countertop for the sink yourself.
3. Undercounter sinks are the most expensive option, they are mounted below the countertop and therefore provide excellent appearance and excellent sealing.

Before you install the sink in the kitchen, and think about how to install the sink in the countertop, you need to choose the product itself. Ideally, this is the connection of a deep sink and a not very high faucet - in this case, less splashes will be created while washing dishes. The sink should be deep enough so that when washing pots and folding plates after a large feast, there is no discomfort.

The material also plays a big role good decision is the choice of stainless steel sink. A good choice would be to install a sink in the kitchen made of enamelled steel.

How to install a mortise sink type?

Self-insertion of the sink into the countertop requires the presence at hand the following materials and tools:

• sealant;
• pencil
• self-tapping screws and screwdrivers;
• jigsaw;
• fasteners (as a rule, they are included with the product).

Advice! Before attaching the sink to the countertop, it is necessary to carefully treat all the seats with sealant. This will provide excellent waterproofing and protect the chipboard from damage due to high levels of humidity.

A do-it-yourself overhead sink is much easier to install above the table, however, the mortise model looks quite attractive on a pedestal with a common worktop, and it also provides high level tightness. The question of how to install a sink in the kitchen is quite easy to solve - you just need to correctly cut a hole for the sink in the countertop.

Installing the kitchen sink in the countertop occurs according to the following algorithm:

1. On the countertop, it is necessary to determine the installation location of the sink and the shape of the future hole. To do this, you need to turn the sink itself over and circle it along the contour on cardboard or directly on the countertop. If your choice fell on the product complex shape, then most likely it is already equipped with a special template, this is necessary in order to be able to cut the desired hole.
2. Then we retreat about 7 cm from the edge, apply the template to the countertop and saw. To do this, it is necessary to retreat about 1.8 cm deep from the edge of the template, so that there is a support for the sides of the sink and cut it out.
3. On the cutting line, you must first make a hole with a drill, and then cut the contour with a jigsaw. The bottom of the tabletop must be secured so that it does not fall out when sawing and does not spoil the edge of the remaining surface.
4. Sealant must be applied along the contour of the cut. They also need to cover lower part joints of the sink, before fixing the sink, it is installed in the hole on the sealant.
5. You can proceed to attaching the sink - it is pressed with the help of the clamps included in the kit.
6. After removing excess sealant, you can start connecting communications.

An inset sink can be fixed flush with the countertop, but it must be remembered that installing the inset sink flush with the countertop is a rather laborious process that requires experience, since for this operation it is necessary to remove the layer of the countertop under the rim. The depth of removal is equal to the height of the side with a layer of sealant.

In the event that you want to install and fix the sink into the countertop with your own hands so that it is located below the level of the table, then you will need to turn to specialists for help. After all this method installation is selected for expensive models- not made of steel, but of natural or artificial stone. Installing an artificial stone sink is also a job for professionals.

For fastening in this case, special tools are also needed, such as a jigsaw and diamond-coated saws. Since in such sinks there may not be a hole intended for draining water, complete sawing of products in industrial conditions is not done. The fastening of sinks made of natural materials is carried out using a special assembly adhesive.

What about sinks? unusual shape, then they are equipped with a paper template, thanks to which you can cut out the installation hole. Often a template is included for a corner or round sink that shows how to cut a hole and how to install a sink sink of this type.

Important! Fastening the sink to the countertop or module using self-tapping screws is carried out only manually. When using a tool, you can create a fairly strong voltage, which can damage the structure.

Features of insertion of round, corner and stone sinks

Despite the shape of the sink, the entire installation procedure is absolutely identical to the process described above. But round and corner options have some features that are worth studying before installing products.

How to properly cut a countertop round sink:

• it is necessary to make several holes along the cutting line at a distance of about 7-10 cm from each other. This is necessary to facilitate the cutting process;
• Some models come with a cutout template. If the Sink is not equipped with a template, then you can make this template yourself.

The cut circle can be adapted to create small table for giving.

The cut surface for the corner sink is made according to this principle:

• due to the fact that the angle of rotation of the cutting lines is less than 90 °, then for easier passage of the jigsaw saw, it is necessary to make several holes - directly in corner connection lines at a distance of 2-3 mm from it.

Installation of a granite or stone sink should be done only by professionals and using modern tools. Then the products will be correctly installed and connected.

The whole procedure is absolutely no different from installing a stainless steel sink and includes the following steps:

• table top markings;
• hole cutout;
• installation of a sink in a countertop. The joints between the countertop and the sink also need to be sealed.

The fastening elements are the same as those of the standard versions described above.
The peculiarity of the installation is that granite sink there are no holes for mounting a faucet and a drain siphon.

They are made using a drill with a special nozzle. If there is no experience with artificial stone, then even a small mistake can lead to a sink defect and its marriage.

Connecting the sink to communications

Once the installation is completed, you can start connecting the sink. To do this, the hoses through which cold and hot water must be connected to a public water supply.

Advice! The connection requires the use of a rubber gasket to better seal the joint.

After the hoses are fixed, the connection must be made in the following sequence:

• it is necessary to bring the outlet of the siphon into the sink ( optimal solution is the use of an S-shaped design, since the bottle clogs quickly enough);
• it is necessary to add a pipe to the siphon (flexible corrugated or angular rigid);
• from the siphon, the pipe is discharged into the sewer;
• all connections are checked for leaks.

It may turn out that the diameters sewer pipe and the pipes coming from the siphon are very different. In this case, it is imperative to use an adapter - a sealing cuff. Thus, the installation of the kitchen sink can be considered complete.

Installing a mortise kitchen sink is a rather responsible task. Poor-quality installation can not only spoil the interior of the kitchen, but also lead to a quick failure of the countertop itself due to the penetration of water under the sink into the cut of the countertop. Most important point The one that needs to be given the most serious attention is the sealing of the sink-countertop joint, and not relying on high-quality processing of the end of the cutout.

Installing a sink in the kitchen only at first glance seems like a simple task. Features of the installation process depend on the type of sink, its location. How to install a kitchen sink correctly?

Types of sinks for the kitchen

Faced with the choice of a kitchen sink, it turns out that there are several types that differ in operating conditions, as well as in the installation method.

There are 3 types of washing:

Tip: the overhead sink is ideal for a kitchen set consisting of separate sections. If the kitchen modules are under a common worktop, it would be more rational to install a built-in model.

How to choose a place to install a sink in the kitchen

Before proceeding with the installation of the sink in the kitchen, you should familiarize yourself with the rules for its placement. So the sink cannot be installed near gas stove– Splashes of water may fall on it and extinguish the fire.

The sink should be located next to the work surface so that it is convenient to wash the dishes after cooking.

The optimal place for placing a kitchen sink is between two work areas (for rough work and for ready meals).

Installing a mortise sink

Mortise sinks can be made from various materials have a variety of shapes and sizes. Their installation in a wooden worktop or chipboard can be done independently, but if working surface the headset is made of stone, it is better to entrust this work to a specialist.

To install a sink in the kitchen you will need:

• Electric drill with wood drills;
• Electric jigsaw;
• Screwdriwer set;
• pliers;
• silicone sealant;
• Scotch masking;
• Square, ruler, pencil for marking.

Note: modern sinks are supplied with fasteners and cardboard templates, which greatly simplify the installation process of the product.

Installation of a kitchen mortise sink is carried out in the following sequence:

Installing a surface sink is much easier than a mortise sink. It is simply put on top of the cabinet and connected to the water supply and sewerage. The sink is attached to the cabinet;

• With sealant, which is applied to the end parts of the cabinet. Then a sink is applied on top and pressed against the cabinet until the sealant is completely set;
• With brackets. FROM inside cabinets are screwed in with self-tapping screws, on which fasteners are baited. The screws are tightened a little, the sink is installed, shifting its mounting angle so that the self-tapping screw falls into the recess of the corner, and the sink itself fits snugly against the cabinet. In this position, the screws are tightened to the end.

Video: Installing the sink. Insert sink into countertop.

Attention, only TODAY!

To install a sink in a countertop, you need to spend a lot of time and work. But if you cut a hole in the furniture block correctly and install it, washing dishes will not seem like such a burdensome task. Next, we will talk about how to cut a countertop for a sink.

Making and applying a template

The process of installing a sink in a countertop consists of several stages. To properly perform this time-consuming work, you must carefully cut a hole in the countertop, while it is advisable to follow the instructions below.

• First you need to purchase a blank sheet of cardboard required size, from which the template will be cut. This work step will be simplified if the manufacturer, as is often the case, makes the template himself and puts it in the product packaging. It remains only to cut the template along the traced contour with scissors. If there is no template, you need to take the sink, turn it upside down, attach it to the cardboard, then use a pencil to draw the necessary outline and cut the template along the finished contour. If there is no packaging with a picture, and there is no necessary sheet of cardboard, the outline of the inverted sanitary ware is carried out directly on the countertop.
• Next, you need to evaluate the future location of the furniture block. It is necessary to know in advance where the mixer will be installed, how to make the piping, whether it is expected to cut the countertop before the final installation. It is also necessary to look at the design of the furniture from the inside. This will allow you to determine which elements, if necessary, can still be cut, and which cannot be touched - the supporting fragments of the tabletop must remain intact and intact.

• Once the template is ready, it's time to use it. To mark the tabletop, you need to attach a template to its surface, while it must be motionless. After this operation, a contour is drawn. The same work is carried out if a factory template is available. On the circled line, it will be possible to cut immediately. If cardboard is used or an inverted sink was outlined in pencil on the countertop, there is additional work to be done. The fact is that the drawn line will repeat the edges of the sink, and its bowl will be inserted into the future hole. Therefore, you need to draw one more contour - the inner one. When drawing it, you need to take into account the distance from the edge of the sink to the fastening elements of the plumbing fixture. The result is new template, which is focused on the dimensions of the bowl. It is applied to the surface of the countertop and a new contour is applied along which it will be possible to cut a hole.
• There is an option in which a cardboard template is attached to the surface of the countertop and a hole is sawn along its edges. If you look at such work with practical side- this is inconvenient - it is better to draw a contour with a pencil. When cutting along a drawn line, there is a real possibility of chipping on the inside edges of the countertop. To avoid marriage, it is recommended to stick masking tape on the surface in the area of ​​\u200b\u200bthe intended contour, which can be easily removed in the future. In order to start sawing, it is necessary to make a hole with a drill in the body of the countertop from the inside of the drawn line. IN drilled hole the jigsaw file is pulled out, after which it is fixed in the tool. You need to saw carefully and without haste, since when pressed, the canvas can go away from the intended contour.
• The resulting cut is cleaned sandpaper, blown and carefully lubricated with silicone. Thanks to this composition, the harmful effects of moisture on the cut surface will be minimized. If any fragments of the furniture block interfere with the installation of the sink bowl, they must be carefully trimmed. Measurements for trimming must be done accurately - it is not recommended to perform such work “by eye”. You need to know that when using the manufacturer's template, cutting out internal elements is much easier and easier, since such nuances are also provided for in its manufacture.

Installing a sink in a countertop

• To get started final assembly washing, it is necessary to do some compulsory work. First you need to try on the pipes and assemble the siphon, then in the internal structure of the countertop you need to make holes for sewerage and water supply. All these works are performed with a jigsaw or a crown. After that, the installation of the mixer is carried out, if a place has been prepared for it on the countertop. In addition, if necessary, cut the hoses. If the mixer will be installed on the sink itself, a place for the equipment is determined on the plumbing fixture and a hole of the desired diameter is drilled.
• Before installing the sink, a sealing tape is put on the sanitary ware - it, as a rule, comes with the appliance. The tape is fixed near the edge, while leaving a special groove free, into which silicone will be poured. Then fasteners are installed in their places, which, when tightened, are not tightened - they will be fixed tightly after the entire structure is finally aligned. If the faucet is to be fixed to the sink, it is time to mount it. The hole is abundantly smeared with silicone, after which the sanitary ware is installed in the hole for the sink. Before installation, the fasteners must be bent. In order for the sink to sit in its place and fit well into the contour of the opening, you need to move the plumbing fixture a little. After that, you need to climb under the sink and finally tighten the fasteners. While the sealant is in liquid state, it is wiped off - after a while the composition will seize and harden. If gaps remain somewhere, they also need to be sealed with sealant.

The sink is installed on the countertop. Plumbing fixtures can be used.

Video

The correct preparation of the hole in the countertop and the installation technology of the sink are shown in the following video:

A photo

When repairing in the kitchen, many of our compatriots, having spent money on materials, want to save on installation, so the question of installing a sink in a countertop on their own is quite relevant.

If the issue of installing a toilet bowl with your own hands is relevant to you, this article will also be useful to you. And installation of heated towel rails - here.

Installation of a sink made of artificial stone

Installing a sink made of artificial stone in a countertop is in great demand, for the reason that composite sinks are pleasing to the eye, strong and practical.

To mount the sink on the countertop, you need to go through a number of steps.

1. The initial stage consists of preparing the tool. Namely: a template, pencil, tape measure, electric jigsaw, electric drill, transparent silicone and a gun.
2. Table markings. If the kit does not include a template, it can really be made in 5 minutes. To do this, a paper sheet is placed on the countertop, then the sink is turned over and outlined. To get a working contour, one centimeter retreats from the existing line and outlines it again. After the template is cut out, and its forms are transferred to the countertop with a pencil.
3. Drilling a hole for the sink and sawing it with an electric jigsaw.
4. Next comes the installation of a stone sink in the countertop. Lowering the sink into the countertop, silicone is applied to its edges to prevent the countertop from swelling and water from entering under the sink.
5. Use the sink only after the silicone has dried. The final stage is the installation of the mixer.

So that the question of how to install a stone sink in a countertop is not tormented by doubts, it is better to study the instructions attached by the manufacturer before starting work.

Installation of a round sink

When thinking about how to install a sink in a countertop with your own hands, you should refer to the recommendations of specialists.

Installing a round sink in the countertop yourself is a doable task, but it requires accuracy and patience.

The correct installation of the sink in the countertop should be carried out according to the template, so if it is not included in the kit, you just need to copy the outline from the sink.

Next comes the installation of the mortise sink directly into the countertop. The template is fixed on the countertop with adhesive tape and the location of the sink is marked on it. The location of the sink must be considered so that it is not too high or, on the contrary, low. A hole is drilled according to the marking and, according to the outline, a notch for the sink is cut with a jigsaw. The cut must be completely cleaned of sawdust. At this stage, it is useful to understand how to properly install the mortise sink into the countertop. It is tried on in the resulting hole and the edges are processed silicone sealant. Such a measure is needed in order to protect the edges of the countertop from contact with moisture.

The sink must be pressed tightly around the edges so that all existing voids are filled with a viscous composition. Then fasteners are tightened along the borders and in the middle of the sink, and the sink is connected to the sewer. After that, the mixer is put into operation and the tightness of the elements is tested.

This example shows that the installation of a mortise sink in the countertop, with strict observance of the manual, can be carried out without calling a plumber.

Ceramic sink installation

A video of installing a ceramic sink in a countertop will be required by home craftsmen at the stage of installing a kitchen set.

Many housewives like the ceramic sink for washing dishes, because it is easy to clean, durable and known for its practical qualities.

When figuring out how to install a kitchen sink in a countertop, the main thing to understand is that the mortise method is based on attaching the device to the table. At the same time, the sawing process itself leaves behind dust and chips, you need to be prepared for this.

So, how to install a ceramic sink in a countertop. Armed with the necessary tools and a template, using a drill and a jigsaw, they prepare an opening for washing. The sink must fit perfectly into the resulting hole.

Installing a sink into a countertop in a kitchen can be considered complete after it has been placed on top. construction sealant, and a rubber band will be laid between the table and the sink. The sink is fastened with clips that come with the kit; they can be plastic or metal.

The sealant will spread widely outside the sink, and will perfectly keep it from shifting. The viscous composition protruding to the surface can be safely cut off as soon as it dries. After that, the sink is ready for use.

Read also:
— Replacement of broken glass during repair interior doors
— Repair of interior doors
— Prices for the installation of locks in metal doors
— Replace the lock in metal door: Can you do it yourself?
- Jig for drilling holes with your own hands
— Replacement of the larvae in the door lock

• Almetievsk
• Volgograd
• Voronezh
• Ekaterinburg
• Zelenodolsk
• Yoshkar Ola
• Kazan
• Krasnoyarsk
• Moscow
• Naberezhnye Chelny
• Nizhnekamsk
• Nizhny Novgorod
• Novosibirsk
• Permian
• Rostov-on-Don
• Samara
• St. Petersburg
• Ulyanovsk
• Chelyabinsk
• Yaroslavl

Do-it-yourself installation of the sink in the counter

How to fix the sink to the countertop?

I think what is meant is the procedure for installing a mortise sink in a countertop (usually a kitchen one).

To work, we need a jigsaw, a screwdriver and a drill (or another tool for drilling - a screwdriver successfully combines both functions), silicone sealant with a gun for it, a simple pencil.

We put the sink on the countertop and circle its outline with a pencil.

Stepping back 1-1.5 cm from the edge inside the contour, draw another one.

We drill a through hole for a jigsaw file - it should be adjacent to the inner contour without going beyond its edges.

Cut through hole. At the last stage, it is necessary to hold the cut piece from below in order to prevent it from falling out.

This is fraught with the formation of chips and damage to the countertop.

We put screw clamps on the sink itself (in the mounting eyes).

We glue the sealing strip from the inside. We generously coat with sealant and install in place.

Sealant can also be added to the seam so that it stands out evenly around the entire perimeter.

We tighten the screw clamps, pulling the sink to the countertop.

Remove excess sealant. Let's dry.

Kitchen sinks are divided into built-in and overhead.

The surface of the washing panel can be located at the level of the desktop or on the plane of the tabletop. Mixer bowls must be fixed between sections of the kitchen set. The curbstone intended for fastening of a laid on sink is a separate element of a kitchen interior. Integrable mortise sinks mounted on the surface of the desktop headsets and floor modules.

Overhead sinks are the easiest to mount. They are a cabinet with a sink, which is complemented by a panel for storing kitchen items.

• The panel is fixed on the pedestal using brackets and slides into the grooves of the pedestal using special slides.
• The sink may come with an adhesive seal that is inserted into the groove of the panel. This prevents moisture penetration.
• Rubber seals, as a rule, do not adhere tightly to the butt surfaces, and have a rather short service life. Therefore, it is rational to replace them moisture resistant sealant, which will help fill the gaps and retain its properties when dried.
• If the underframe does not have internal elements, this allows access to repair pipelines, as well as to clean the siphon and sewer pipes.
• Supporting bars must be attached under the overhead sink, which will help to significantly increase the strength of the structure.
• Before attaching the sink to the countertop, a mixer is mounted, and water supply hoses and a siphon are also installed.
• The overhead sink is fixed with special fasteners, having an L-shape and an overhead slot. For reliable fastening, it is enough to install 5 such elements.

  Pre-mark on the inside of the cabinet places for fastening self-tapping screws. It is better to screw in the screws with a screwdriver, as using a screwdriver can damage the countertop.

• The sink bowls can be different, so you need to transfer the geometric parameters of the bowl to the surface of the countertop as accurately as possible. Most often, manufacturers of mortise sinks to kitchen set attach a special template on which to draw special form holes won't be difficult.
• Make a cut line from the sides of the bowl by about 1 centimeter. Mark the contour points, insert a jigsaw and cut a hole to fit the bowl.

  Don't forget that on outside masking tape must be glued to the contour to protect the surface of the countertop from damage by the foot of the jigsaw.

• When installing a conventional mortise sink, the cut line does not require additional processing.

  But at the same time, the edge must be perfectly even. This will help in the future to ensure complete tightness of the connection and a decorative appearance.

• Clean the cut surface.

  How to embed a sink into a countertop - let's do a great job

  Apply a layer of sealant and install the sink. After the sealant has completely dried, fix the sink with clamps. Planning to install in the kitchen individual elements headset, use an underframe with an overhead sink.

Together with the new sink, there should be, in the kit, fasteners. If there are no fasteners, then you can use small metal corners, I did this at home. There is not a big nuance, before buying corners with self-tapping screws, decide on the thickness of the material from which the countertop is made, too long self-tapping screws can go through.

In general, ordinary silicone can easily and tightly hold the sink, if it is applied correctly, correctly, it is over the entire surface.

It is also important to correctly mark and cut a hole for the kitchen sink, it (the hole) should not be too wide, the sink should fit into it tightly and securely, plus room for bumpers. If you don't want to be self-employed, then special mounts for the sink are sold separately, just say "sink mount" in the store, they are sold individually, depending on the configuration of the sink, decide on the quantity, four mounts are enough for a square one, and two are enough for a round one.

More questions about your topic:

leave a comment

Builder's vocabulary:: Repair questions:: Calculators:: Special equipment:: Miscellaneous

2006 — 2017 © user agreement:: communication with the site administration [email protected]

Installing the sink in the countertop: overhead sink

Carefully chosen by the hostesses, the countertop sink is often chosen specifically for arranging the kitchen. In the plumbing store you will be offered classic sinks of various shapes.

On the showcase there are models with straight, rounded corners, perfect round or oval shape. They may be different size, and the design of the product consists of one or two or three bowls.

The depth of the sink is within 20 cm, which is enough to make it convenient to wash dishes, vegetables or fruits. From a mortise sink, overhead models differ in the presence of an additional plane - the “wing”.

It is used for hot items, dishes, as a place for drying fruits. About the advantages of this type of sinks and how it is made correct installation sinks in the countertop you will learn from this article.

Photo 1.

Countertop washbasin.

Installing an overhead sink on a countertop: the advantages of an overhead sink

Installing an overhead sink on a countertop is easier than installing a mortise one: unlike it, an overhead sink is mounted on a special pedestal. As a rule, an overhead sink is installed on the countertop of a kitchen cabinet made of wood, chipboard and other materials.

Some models are equipped with a wooden side, they increase the rigidity of the product and protect the cabinet from damage.

Overhead kitchen sinks are most often used in everyday life. They are made from stainless steel High Quality. During its "life" a stainless steel bowl interacts with tap water(and it rarely has a neutral pH), detergents and various cleaning agents.

The higher the quality of the steel chosen for its manufacture, the longer it will serve you.

Photo 2. Overhead sink - convenient and practical solution for kitchen.

The installation of overhead sinks differs from the installation of mortise bowls and the technology of installing sinks in the bathroom.

Installing it is easier and simpler, any man can handle this task. The product is superimposed on a kitchen cabinet, cabinet, table. For installation of additional devices - it is not necessary.

There are 3 main advantages of overhead sinks:

1. Ease of maintenance. Stainless steel is easily and quickly cleaned of dirt and long time maintains a presentable appearance.

   The metal used for manufacturing does not oxidize upon contact with detergents, is not afraid of liquid high temperature. The surface of the bowl is easy to clean, it will not fade and retain its original shine.

2. Ease of installation.

   You can install the product yourself. Even if you have never held a tool in your hands, the instructions on how to install a sink will help you to carry out this process quickly and well.

3. Price. A countertop model costs less than an inset sink of the same size.
4. Multifunctionality. Overhead sinks are equipped not only with a bowl for washing dishes, but also with an additional surface. The plane is used for drying dishes, vegetables and other items.

Installation of an overhead sink on a countertop: types of overhead sinks

Sinks for kitchen overhead type differ in the type of manufacture.

Some are stamped and some are welded. There is another type of overhead sinks - bathroom sinks, they are a separate bowl that is installed on the cabinet. The shape of the bowl can be different - oval, round, rectangular.

Photo 3.

As a rule, overhead sinks are installed in kitchen cabinets.

Stamped bowls are made from sheet steel. The number of seams is minimal. Appearance is attractive. The cost of this type of product is democratic. The production technology allows us to offer sinks with a depth of no more than 15 cm. This characteristic is attributed to the disadvantages of products of this type.

Welded sinks in their design have several parts.

Each is made separately, then they are welded together, turning into a single system. The surface of the seam is ground and polished. With this manufacturing method, a deeper shape of the product is obtained.

Kitchen sink installation. How to embed a sink into a countertop

In assortment of a bowl of different depth and a form. The depth of the bowl reaches 20-22 cm.

How to install a countertop sink

There are several options for mounting a surface sink.

The simplest is mounting on a cabinet or a special table. The width of the surface of the sink in this case is slightly larger than the size of the underframe. This is a prerequisite, so that the sides are well hidden side ends bedside tables. Difficulty of option - choice right size sinks. It is best to purchase furniture and a sink at once. In another case, you need to carefully take measurements and buy a bowl, the inner size of which will ideally match the hole in the cabinet, and the width of the sides of the sink will cover the end walls of the bedside table.

Decided to start installation?

Prepare everything you need for this process: a screwdriver, a set of screwdrivers, fasteners, a mixer, a siphon, sealant, plumbing tape, gaskets, flexible hoses for water supply.

First of all, prepare the ends of the cabinet.

They are treated with silicone sealant. Use a spatula for easy application. Silicone will protect the furniture from moisture and securely hold the product in the "saddle". Choose a quick-drying sealant. You won't have to wait long before you can start using the sink. For wooden and plastic countertops use alcohol sealant. After applying silicone, install the sink, press it around the entire perimeter. For reliable clamping use a clamp.

Then remove the excess sealant. And after it dries, they begin to connect the bowl to the sewer and install the mixer.

To make it easier for yourself, you can install the mixer in advance, immediately before installation.

And the siphon will have to be connected later, after the sealant has dried. The choice of a siphon must be approached carefully, especially the owner of a private house. Right choice siphon and a number of activities will help eliminate unpleasant odors from the sewer.

Before starting the sewer drain, check the tightness of each joint. We mount the mixer in a hole specially designated for it.

For reliable fastening, use a rubber gasket, its diameter must match the diameter of the base of the kitchen faucet.

How to install an overhead sink in a cabinet using brackets

Surface-mounted models are mounted in a cabinet. Usually the cabinet is called the underframe. They are a cabinet of a headset type, in which there is no top cover and back wall. Such a cabinet is quite simple to assemble or make yourself. To simplify the task, they purchase both a kitchen set and a sink according to the size of the table-cabinet for it.

Self-assembly of the product takes place subject to a certain sequence.

Stage 1. Before installing the sink, the masters recommend installing a mixer. While the product is not fixed, you can smoothly and securely screw the tap and ensure the tightness of the water supply.

Stage 2.

Prepare your brackets.

They come in a set. You can also purchase special mounts separately. To begin, place the L-shaped mounts on the table base. The place of application is outlined with a pencil. Self-tapping screws are screwed into the indicated point. Their length should be 16 mm. The screws protrude no more than 5 mm above the pencil mark.

Photo 4.

Placement of fixtures at the base of the table.

Stage 3. A layer of sealant is applied to the ends of the table or cabinet with a spatula. Silicone plays the role of glue and will protect wooden surface from water drops.

Photo 5. Application of sealant.

Stage 4. Attach the sink to the attached screws. Tighten the screws until the product fits snugly.

Then the fasteners are tightened. The exposed sealant is removed with a knife or a rag.

Stage 5. Connection to the sewer. This is the final stage. To connect, use a siphon with a corrugated hose. It is attached to the screw, through the mesh in the drain hole of the sink. For the tightness of the connecting elements, gaskets and plumbing tape are used.

If you decide to put a countertop sink on the countertop, then you need to study the instructions on how to properly install the mortise-type sink.

In this case, you will have to make a hole of the right size for the sink and secure it with double-sided tape and self-tapping screws. The markings on the countertop are made according to the finished template.

It is included. The hole is cut with a hacksaw or a jigsaw. In order for the product to sit well in the prepared hole, you need to grind the ends. Before the final fixing of the bowl, do a fitting. The product must be freely hung in a prepared place.

The next step is also to process the sections of the countertop with a sealant.

And fasteners are screwed to the inner wall. Fasteners are included with kitchen sink overhead type. If not, please purchase them separately. Suitable for sink installation side mounts for kitchen cabinets. After you screwed the fasteners with self-tapping screws, apply sealant to the edge of the sink, put sealing tape on top of it.

Double-sided tape is also suitable for sealing joints. It remains to install the sink and screw it.

As you can see, the installation of an overhead sink is a simple task that does not require special skills and tools.

You will cope with it with due diligence no worse than the masters.

Video: Installing a countertop sink

Today the market offers a huge range of sinks for the kitchen of the most different models and forms. When purchasing a sink, buyers can choose decorative trim, material, shape, as well as the color of the sink. However, the main criterion that should be taken into account when choosing a sink is its resistance to aggressive environments, the ability to maintain its previous view, despite mechanical damage, temperature fluctuations and exposure to detergents.

Types of kitchen sinks

There are four main types of kitchen sinks.

The classification depends on the type of their installation, taking into account the conditions of subsequent operation.

How to cut a hole for a sink in a countertop?

Today, the following types of sinks are very popular:

1. mortise- sinks that cut into the countertop, which gives them an attractive appearance and convenience;
2. undercounter sinks- are installed in a countertop created from solid wood or stone;
3. integrated- installed without joints (sinks of this type are also called seamless);
4. overhead sinks– are mounted on a curbstone and are capable to replace a table-top (differ in extremely simple installation).

The most popular type of sinks for the kitchen is mortise in the countertop.

Therefore, in this article we will tell you in detail about how to properly install a sink in the kitchen.

Competent position and marking

Before proceeding with the installation of a mortise-type sink, you should first determine its correct position and mark it.

To do this, you need to turn the sink upside down and attach it to the countertop. Then place the sink on the countertop in the way you want it to be. At the same time, it is necessary to take into account how comfortable it will be for you to wash the dishes later, as well as a number of other factors individual for each individual situation.

The distance from the edge of the sink to the back of the countertop must be at least 4 centimeters.

Possible big values However, this distance should in no case be less than 4 centimeters. The reason for this is that the worktop reserved for the installation of the skirting board for the kitchen should not be covered by the sink. When you decide where exactly to install the sink, then circle this area along the contour.

Before proceeding with the following installation steps for a sink type sink:

• outline marking,
• drilling holes,
• sawing the opening

you need to remove the table top from the furniture.

Since for self-assembly you will need to create the most comfortable conditions. Most best option- put the tabletop on two stools set at the edges.

Working contour marking

Having outlined the initial contour of the sink, you can begin to mark the working contour.

As a rule, professional kitchen furniture assemblers prefer to mark with a marker (medium fat content - approximately 0.5 to 1 millimeter). Do not be afraid to spoil the countertop, because in the future you will still cut off that part of it on which the markup was applied. To create a working contour, it is necessary to put marks from the initial one by 1 or 1.5 centimeters inside the countertop. Then connect them.

Sawing in the worktop of the opening

After marking the working contour, you can start drilling holes in the countertop.

This is done using a standard wood drill, the diameter of which is 10 millimeters. The number of holes depends on geometric shape sinks.

For a sink having a square shape, three holes will be enough, and for a round one - at least two. Here it is necessary to make sure that the connection converges at a comfortable distance for you, since during the last stage of installation you will have to hold the top of the countertop from below so that the sawn off piece does not fall with a loud roar inside the cabinet.

There is also another important nuance: it is necessary to choose the optimal place to start sawing, i.e.

the final step in the hole joining process should take place as far away from you as possible. Otherwise, you will experience extreme inconvenience and even endanger yourself when you stick your hand under the countertop: we must not forget that the jigsaw file has quite large revolutions.

Sealing and installation

After sawing the opening, you need to wipe the dust from its edges and be sure to thoroughly coat it with some kind of waterproofing material (epoxy resin, silicone or sealant).

On the area where the countertop is in contact with the sink, that is, on the end part of the opening, it is necessary to apply a non-greasy layer of transparent silicone (the best option is silicone with an adhesive base), without gaps.

In this case, the material for waterproofing should not have time to harden. In order to prevent hardening, it is necessary to first prepare the sink for installation and sealing - snap the fixing devices that come with it onto the sink. After that, you need to insert it into the opening for installation, fix it with fasteners, and remove the excess part of the sealant with simple paper towels.

That, in fact, is all!

You have installed a mortise-type sink, and now you just have to enjoy the fruit of your successful work! If you strictly adhere to all the operations specified in this manual, you will be able to install a sink of any shape and from any materials in a short period of time.

(Last Updated On: 03.10.2017)

Corner kitchen sink - perfect option for a small space. It fits perfectly into the corner kitchen set and well saves such missing square centimeters of usable area.

Selection rules: which material is preferable

The variety of materials from which kitchen corner sinks are made is great.

It could be:

• stainless steel (cheap, accessible to everyone);
• ceramics (kaolin/faience);
• fake diamond;
• composite materials (corian/silacryl);
• granite and marble for expensive interiors.

Fashionable at the end of the 20th century, enameled sinks are a thing of the past, as enamel is short-lived, quickly fades, cracks and chips off if something heavy is dropped.

Ceramic models have many advantages - water flowing down their walls does not make noise, the surface is not afraid of exposure to chemicals and high temperatures, and it is also easy to clean with conventional means.

Stainless - the cheapest, are not afraid of acids / high temperatures / shocks.

However, their surface is easily scratched and often looks untidy, as water droplets, when dried, give it an untidy appearance.

For an average apartment with simple design stainless or ceramic sinks are fine. At the same time, stainless steel will perfectly fit into a modern interior.

Shape and dimensions

Corner sink for the kitchen can be of any size and shape.

First of all, you need to start from the size of the room itself, as well as from the furniture that is installed in it. A small sink is appropriate in a small kitchen.

The cabinet for her should also be suitable in size.

The shape of the corner sink can be any - round, oval, square, rectangular.

Do-it-yourself installation and connection of a mortise sink

The best solution may be to install a sink of two sections (two sinks), supplemented by a place for folding the washed dishes.

Types of mounts: how to choose the right one

All kitchen sinks (not only corner sinks) are divided by type of attachment:

• under-table;
• mortise;
• overhead.

Underbench ones are attached in a special way to the table top from below, mortise ones are installed in a special hole in the upper part of the cabinet, overhead ones come with a “leg”.

Installation: tools and workflow

Installation of a corner sink for the kitchen is quite simple, so any man can handle it.

To work, you will need the following tools:

• gas key;
• pipes / corrugated hose;
• rubber seals / plugs;
• siphon;
• screws and corners.

You will also need the sink itself, a cabinet under it, preferably with a hole, otherwise you will also need a jigsaw to cut it out.

First, the old sink, faucet and all fasteners are dismantled.

Then a new plumbing is mounted, a sink is installed on the pedestal or “leg”.

The cabinet is tightly attached to the walls and floor. Then the mixer is installed, and the system is checked for operability (no leaks).

If corner sink for the kitchen is installed correctly, there should be no leakage.

Pros and cons of models installed in the corner

When choosing a kitchen sink, choose the right faucet.

His gander should not be too high (splash will fly in all directions) or too low (even a small saucepan cannot be washed under it).

An undoubted advantage of corner structures can be considered a good space saving, the ability to choose any shape and type of fastening, additional space for folding washed dishes (if the model is equipped with a special “wing”).

The only negative in comparison with conventional sinks is their smaller size.

However, for small kitchen it's hard to call it a minus. Large-sized dishes, which usually happen on holidays, can also be washed in the bathroom.

From the author: Good day, dear readers! Today we will introduce you to the algorithm for performing work on installing a kitchen sink. Organize water supply in the kitchen - milestone any repair work. You may need the help of a professional to install a countertop sink. But, if you are confident in your own abilities and have already been engaged in the repair of premises, you can try to perform this procedure yourself.

What tools are needed to install the sink?

Installation of the sink, produced independently, will not do without special tools. You will need:

• hacksaw;
• screws;
• drill;
• jigsaw (tool for woodworking);
• cardboard, pencils, scissors and wide adhesive tape;
• sealant (silicone is best);
• brackets and elements for fasteners;
• drills in a set;
• sandpaper;
• rag.

Be careful with the canvas of the countertop: in case of unsuccessful movements, you may have to change it. Before starting work, check how strong you have purchased the sink, and build on this knowledge during the installation process.

What are kitchen sinks

There are several types of structures. They differ in how they are installed.

1. Overhead. Such a sink implies any supporting structure, for example, a cabinet. After installation, there should be a small space between the structure and the countertop itself. Such products are usually made of loose, thin material.
2. Underbench. Made from a more durable material than overhead sinks, these sinks must be mounted below the surface of the countertop. This strengthens the structure and "hooks" it to the supporting pedestal.
3. Mortise. The type of sinks that we will talk about today. A similar design simply crashes into the countertop during installation. It does not require additional supporting pedestals and similar structures.
4. Mounted. Such a thing is convenient: it provides quick access to all pipes.

In addition, sinks can be various forms, have more than one bowl, and be made from materials of varying strength. Stainless steel, ceramic, acrylic, glass or granite are the most common materials used for kitchen and bathroom sinks. You should pay attention to these characteristics in order to understand how you need to work with your chosen product.

Don't forget about additional elements which may also require installation. Such elements include filters, special valves, secondary outlets that complement the main outlet.

How to install a mortise structure correctly?

If possible, do not use a screwdriver. Manual screwing is considered the strongest and safest. Without a screwdriver, you do not injure the sink, which may be subject to deformation.

How to attach a sink to the wall without using a cabinet?

You will need mounting brackets. They can be purchased at the repair and construction supply store.

1. Mark the wall at a height of eighty centimeters from the floor.
2. Measure back wall models. After that, make a second marking on the wall below the first by as many centimeters as you got after measurements. These markings will be the bracket attachment lines.
3. On the product, the mounting points of the brackets are already marked. You will need to measure the distance between these locations and transfer the measurements to the anchor lines. At the resulting points, you need to drill small holes.
4. Start screwing on the brackets. Do this with special tools, not with your hands! You will need as many fasteners as the number of points for connecting them to the sink is indicated in the plan that comes with your purchase.
5. Fix the model with brackets. You do not need to additionally protect the wall with various gaskets.

Choose the strongest brackets. They should last you as long as possible, so you should not save on such materials.

How to choose a kitchen sink?

Pay attention to functionality. Choose a sink that will suit you with the number of taps, wings, bowls. In addition, it is important to consider the availability of space for drying. In sinks that are mounted in the countertop, such a place is usually provided.

Don't forget capacity. If you cook daily big family you will need a roomy, deep sink.

The material from which the model is made is important. The stronger it is, the more durable your purchase will serve. Check the reviews of a particular company's products on the Internet to choose the design that suits you personally.

In the design of the sink, nothing should confuse you. The sink should be comfortable, aesthetically attractive. In addition, the design can not argue with the design kitchen sets, so choose the one that fits perfectly with your surroundings.

If it is important for you to have a separate faucet with filtered water, pay attention only to those models that meet this requirement. Do not buy a sink that does not satisfy you completely. As a result, such a model will not please you with durability, since you will see only one drawback.

We wish you good luck in choosing and installing a mortise sink! This type of sink is considered the most convenient and durable in operation. When using such a sink, moisture does not accumulate between the cabinets, and the products themselves are very practical. Mortise models are usually made of very durable materials, which significantly increase the service life of the product. Be careful when installing such a product and do not forget about safety precautions so as not to accidentally damage either the objects around you, or yourself or your assistants.