Workshop of useful homemade homemade homemade products. Interesting and useful homemade products for the home

Interesting homemade products for giving are waiting for you in this article. You will learn how to make a lawn mower from an old washing machine, make a sink, country shower, a dryer from scrap materials.

Useful homemade products for a summer residence - do-it-yourself washing

Not everyone has the financial ability to buy a car "Karcher". If you can't get it, why not invent it? Homemade sink will allow you to do without running water, reduce water consumption and thoroughly wash your car, fence, garden path or other items.

Here's what you need for such a homemade product for a summer residence:

• plastic canister with a capacity of 5–20 liters;
• set of hose connectors;
• automobile nipple;
• piece of hose;
• silicone sealant;
• sharp knife;
• compressor or car pump;
• watering gun.

Take a hose nozzle kit that includes 2 connectors, 3/4 threaded nipple, 1/2 reducer.

Here is the principle of operation of such a homemade product for a summer residence: you connect the gun to the hose, attach this device to the bottom of the canister. A nipple will be built into its neck.

Fill the container with water, but not to the top. Then screw the cap back on and pump air in. This will create pressure and water will run well when you pull the trigger of the gun. Here's how to assemble such a mini-sink.

Carefully cut a hole in the cover with the tip of a knife. It should be slightly less than the diameter of the nipple stem. Also cut a circle of the desired diameter at the bottom of the canister side.

Insert the nipple into the cover.

Now, helping yourself with a wire, put the sleeve in the hole provided for it. Apply silicone sealant to secure the junction of the sleeve to the canister.

It is necessary to tighten the lid and perform the rest of the work only after the sealant has completely solidified. Then you connect one end of the hose to the water gun and the other to the canister.

Pour water into a container, but not to the top, so that there is room for pumping air. But do not pump too much so that the canister does not deform or burst under pressure. See how the union should be screwed in and the connectors installed.

If everything is done correctly, then when you pull the trigger of the water pistol, the water will gush with a good stream. You can adjust the pressure by twisting the tip of the gun.

At the dacha, you can hardly do without a shower. Try to make an unusual, and tropical, then you can enjoy even more water treatments.

How to make a rain shower from scrap materials for a summer residence?

If you have just recently purchased a plot and you do not yet have a washing room, then you can take a shower right on the street, fencing a small area near the fence with a curtain. To make such a rain shower, very few components are required, these are:

• bracket;
• wire;
• flexible hose;
• metal beer can;
• hose adapter;
• awl;
• nails.

Nail the metal bracket onto wooden fence so that the device turns out to the right height... Screw the adapter to the end of the hose, fix it on the slots of the beer can. The junction can be treated with a sealant. Use an awl to make many small punctures in the jar.

Wire the top of the hose to the bracket and attach the other end to the plumbing or pump. When you lower the pump into a barrel of warm water, you will be able to enjoy a pleasant water treatment.

You can also make a rain shower head using a disc container as it. In its center, you need to fix a plastic adapter that is attached to the shower hose, and the central axis of the discs must be removed. Use an awl to make holes at the top of the cover. Glue all fasteners well with sealant. Such a nozzle is held on a bracket using a thick wire or on a rigid pipe.

If you have a desire to make a rain shower, then you can use plastic pipes for this.

You need to supply water to them, first make many small holes with a soldering iron, and then enjoy the pouring drops. Children like such water procedures.

But do not forget to first check the water in the container from which it will be poured into the shower, it should warm up in the sun.

And to make a stationary shower, you first need to pour water into a tank or a barrel, which will be located under the roof or on the roof of the building. On a warm summer day, the water warms up well here, and you can wash yourself in plenty. To be able to do this even in cooler weather, then it is necessary to provide a heating system in such containers.

Dacha shower with your own hands

Before installing it, you need to make a shower stall. If possible, you can craft it out of wood by placing this small structure on the base. Put wooden door or limit yourself to this shower curtain.

There are more simple options... If you have oilcloth fabric, then use it.

Another option is to purchase an impregnated fabric or use an old awning or tent.

If you made a fence from corrugated board and you still have materials, then try to make a shower for giving out of them. Metal pipes you need to dig in according to the markings, fill them with concrete. When it dries, cut sheets of corrugated board are welded to the racks. One of them will become a roof.

If you have little wooden planks, then implement the option shown in the next photo on the right. And on the left is a shower, which is made like a wattle fence. So the materials for him will cost almost free.

When the shower is ready, you can install a water container on it. To make it warm better, you can make a kind of coil from metal or from a hose. Then the water will warm up more actively.

These and other homemade products for summer cottages allow you to make the most of the available containers.

To be able to receive warm water even when it is not heated by the sun, use electric heating. To do this, you can plastic barrel arrange vertically or horizontally. Then it will be necessary to mount ten on one side, and on the other? water bay fitting. Make an overflow hole so that excess liquid flows out and you can see that the container is already full.

Now it remains to install the tank. Usually a shower roof is used for this. You can put a flat tank here, made of iron or plastic. You can also make a shower canister out of metal or iron barrel... If you need to heat the water, then a heating element is mounted in the barrel.

Check out other examples of what you can do on personal plot do it yourself.

Interesting homemade products for giving with your own hands

Gardening tools are essential for working on the ground. Often, the store does not sell very high-quality sets. After a short use, the handle of the shovel breaks off, or the teeth of the hoe become bent. Therefore, if possible, try to make the tools yourself.

Take:

• stalk;
• a fragment of a water pipe;
• trim from a two-handed saw;
• screws;
• screws;
• a fragment of a profile pipe with a cross section of 3 cm.

Using a grinder, cut a piece of pipe. Taking a lever tool, you need to cut out a piece of pipe, unbend the sector and in the place where the handle will be, you need to work with a hammer to give the future hoe the desired shape.

To make a blade, take a piece of a two-handed saw and sketch out the outlines of the future hoe. Punch two holes.

At the same distance and the same diameter, you need to make 2 holes on the hoe itself, and then cut out a fragment from a two-handed saw.

Drill these holes with a drill and drill designed for metalworking. Connect the two parts with rivets, which are screws.

Now drill a hole in the top of the hoe to attach the handle here.

Make another scoop, which is very interesting to work in the beds. Then such homemade products for giving will allow you to find a very durable set of tools.

Saw off the desired piece of the cutting with a grinder and begin to unbend part of it with a chisel.

Then, using the lever tools, unbend this part almost completely.

It remains to work with a hammer so that the scoop blade takes the desired shape. Using a felt-tip pen, draw the outlines of its working part and cut it out with a grinder.

Use an abrasive wheel to smooth out the edges of the shovel and make them smoother. Now sand the tool with a flap wheel. This shovel will become so shiny.

Also drill a hole in it for the handle, then insert it and secure with a screw.

Cover the cuttings of both tools with antiseptic and then varnish. Now you can use the tools as intended. If you want, use the same principle to make a ripper for the beds.

It is very exciting to create such things for a summer residence with your own hands. Maybe after you make your tools, you want to make a fixture that can dry some of the harvest. See how one gardener did it.

How to make a dryer for fruits and vegetables?

See what materials you need to take for this:

• sheet metal;
• square pipes;
• locking mechanism;
• polycarbonate sheet;
• self-tapping screws, screws;
• 2 door hinges.

But what tools you need to arm yourself with:

• grinder;
• welding machine;
• drill;
• a clerical knife;
• tape measure and marker;
• scissors for metal;
• hacksaw.

First you need to make the base for the drying cabinet. Make a frame from square pipes... Horizontal and vertical posts sawn off so that the edges are even. And the tips on the connectors should be chamfered.

The door here will be metal. To make it, cut 4 fragments from the iron pipe and weld them into a rectangle. Then you need to sheathe this base with metal using screws with nuts and self-tapping screws. If possible, weld on the steel sheet. To make a baking tray holder, attach wooden blocks to the back of the frame. Take self-tapping screws for this. In this case, on each side there are 4 wooden blocks for 4 trays.

An absorber is installed in the dryer. Take sheets of metal and paint it black. Use heat resistant paint. When it's dry, place this blank on the bottom of the dryer.

For the absorber, take a thick aluminum or copper sheet, or at least steel. These materials conduct heat well.

Now you need to sheathe the outside of the dryer, make the roof transparent, made of polycarbonate. Then the sun's rays will penetrate here well. Glass can also be used. Close up ventilation windows mosquito net so that insects do not fly in here.

Attach the hinges and locking mechanism to the door. Reattach the door in place. Look, what a wonderful beautiful and spacious dryer turned out to be.

It remains to make baking sheets. They must be breathable. First, put together the frames from the bars, and then attach the metal mesh to them.

Now you can slice the fruit and watch your device work. Place a thermometer in the dryer to keep track of the temperature. It should be in the range of 50–55 ° С. If the temperature is colder, cover the bottom holes with a rag.

In such a homemade dryer, you can dry not only fruits, but also vegetables, spicy herbs, fish, meat, roots.

If this diagram of the device of such a device seemed complicated to you, then you can make a dryer out of metal barrel... A hole for the door is cut out in it, and racks made of metal mesh are inserted inside.

So that water does not flow here and there is better ventilation, such a roof is installed on top.

You can upgrade this fixture by installing a fan and an electric heater inside.

If you want to make your own lawn mower, then this is also possible.

Turn the old one into it washing machine, for example, this one.

And if you still have old bedside table, then you will make a platform out of it for the future almost self-propelled device. But you only need a door from the bedside table.

Drill holes in the center of the motor shaft. Cutting knife make from an old two-handed saw. It is necessary to saw off from it to size the desired shape, cut a recess inside.

Attach two wooden pickets that will become the handles of the mower. Remember to secure the motor and extension cord to it. Now you can test such an interesting unit.

If you are interested in other homemade products for giving, then it will be useful for you to watch the following video.

A lot of interesting ideas await you in the first video.

And with cool homemade products from plastic pipes you can get acquainted if you watch the second plot.

Crafts made from old objects and things to which you can return a second life can make your home much more comfortable. Some made homemade products for household with their own hands, they can significantly save the home budget, make work easier or make the surrounding interior more interesting. And even if difficulties arise in the process, overcoming them will be worth it.

Homemade products for a home workshop

In almost any home there is always some set of tools necessary for the household. But sometimes situations arise when, to work in your own workshop or garage, you need some kind of device that cannot be purchased in the store or it is very expensive. In this case, a way out can be found by making it with your own hands.

Balloon Forge

This metal heating device will become irreplaceable assistant in a home workshop. The forge can be safely used to make original items using artistic forging. These will be truly unique forged items.

For the furnace, it is best to use an empty 25 liter gas cylinder. Its ends are cut off with a grinder, and the furnace door and its rear part will be made from the cut parts. The inside of the cylinder is covered with refractory ceramic wool, which is able to withstand temperatures over 1200 0 C. From above, it is coated with fireclay clay (lined), which can withstand temperatures up to 1500 0 C. After lining, fireclay slabs or refractory bricks are placed on the bottom of the hearth.

A hole is drilled at the top and a small squeegee is inserted, allowing you to insert the nozzle of a gas burner, which can create a temperature in the hearth of more than 1000 0 C - quite enough to heat the metal to a certain temperature suitable for forging.

Dismountable garage crane

In the manufacture of such a lift, the cash costs will be much less than buying a factory model. To make it, you will have to spend only on materials, half of which, perhaps, can be found in the garage.

Materials required to assemble the lift:

1. Two racks - shaped tube 100x100x2350.
2. Cross bar - steel pipe arbitrary length with a diameter of 100 mm.
3. Four supports for the bar - profile pipe 100x100x600.
4. Base and braces - corner with 100 mm shelves.
5. Two metal rope rollers.
6. Four wheels for movement.

For the hoist it is best to use hand winch with a worm gear with a maximum load of up to 500 kg, which is attached to one of the racks of the crane.

The design does not take up much space in the workshop, easily moves on hard surfaces and is quite convenient for removing the engine from the car.

Mobile tool rack

The main highlight of this rack is its small size., but at the same time it is possible to place a large number of tools on it, and if necessary, quickly move it to any place or adjacent room. It is very convenient to use such a rack in your workshop or when conducting construction and repair work in large rooms, especially when you need to carry tools frequently.

The rack can be assembled on the basis of a collapsible plastic rack installed on a homemade platform with wheels (cart). The platform is made precisely to the dimensions of the rack from a metal corner with 45x45 mm shelves or a sheet of plywood with a thickness of at least 10 mm. Furniture metal wheels are used for movement.

In addition to the rack, you can make and fix fasteners for building levels, extension cords and other tools that can be stored hanging.

To help the hostess

There is not always a financial opportunity to buy, for example, something from new furniture in a furniture showroom or place an order for its production. But you can always get out of this situation by making the right thing do it yourself, while making it attractive and unique, using available tools for this.

Cork backsplash

A backsplash is a wall surface between a worktop and wall units. Usually this part of the wall is lined tiles... But to cover it, it is possible to use many other materials, for example, to glue wine corks on the wall.

This exclusive decor looks pretty gorgeous.

Before gluing, each cork is cut lengthwise into two halves with a sharp clerical knife. It is advisable to paint the wall black, which will accentuate the seams between the corks.

The plugs are glued to the wall with liquid nails in a checkerboard pattern or with a certain pattern, since it will hardly be possible to lay them out perfectly, and the curved rows will visually look disgusting.

The corks themselves are not afraid of moisture, but they quickly get dirty and poorly washed, so it is best to cover them with a glass screen made of tempered glass. True, you will have to spend a little money on it and order glass in a special workshop, where they will cut it to a given size and make holes for sockets and fasteners.

The glass is fixed to the wall with anchor dowels, which can be purchased at almost any hardware store.

Although the apron decorated wine corks may be expensive, but achieved result will be worth it.

The surface of the countertop, as well as the wall, can be decorated with corks and covered with tempered glass.

Hinged folding table

Mounted on the wall folding table IR allows you to save some space in the apartment. In the unfolded state, it can protrude from the wall at a distance of no more than 10 cm and does not bother anyone at all, but when unfolded it can replace a full-fledged table.

There are many options where you can use a folding table fixed to the wall. Here are just a few of the most basic ones:

Shower for giving

There is probably nothing better than freshening up under the tap of water on a hot summer day, especially if he went to work in the garden. Naturally, only a shower will solve this problem and remove the fatigue that has accumulated during the day.

The shower can be installed by yourself without involving outside help, the main thing is to choose a place for it and decide on the type of shower cabin.

Three types of cabins stand out among summer showers., which you can freely build on your own:

Installing a simple shower is done in this way:

1. The frame of the shower stall is made, which can be assembled from metal, timber or other materials at hand.
2. A metal or plastic water container is installed on the roof of the assembled frame, which can have a volume of 50 to 200 liters.
3. It is advisable to paint the metal container black for better water heating. Additionally, several electric heating elements can be installed in the container, then you can take a shower in cloudy weather.

The booth can be sheathed with boards, plywood, slate, or simply covered with tarpaulin or cellophane wrap with folding canopies.

For self-construction

The topic of construction or renovation probably worries everyone. And, of course, everyone who deals with it wants to finish it as soon as possible with minimal financial costs. Therefore, if you want to save money, you can make some materials for construction on your own. For example, it can be wall SIP panels or such useful tool, like a vibrating plate, the need for which often arises for many owners of a personal plot.

Homemade SIP panels

For their manufacture, you need to prepare a flat, hard platform. Having laid an OSB sheet with a thickness of 10-12 mm on it rubber spatula apply glue to it with teeth.

Then put sheets of foam grade 25-30 on the glue. After that, on top of the laid foam plastic, as well as on the bottom OSB plate, an adhesive mass is applied, and the second OSB sheet is laid on top.

If several panels are being made at the same time, stacked in a pile, work should be done quickly, until the glue hardens. Usually, in this way, no more than 4-5 panels can be prepared at a time.

After the blank for the formed slabs, you need to create pressure using a press. Since at home, of course, hydraulic press no, it can be replaced with a thick plywood sheet laid on the prepared SIP-plates over the entire plane and loaded for 2-3 hours, for example, with several bags of cement, sand or other cargo. You can even use by car, having driven onto a plywood sheet along a pre-made overpass.

After the glue has completely dried, the homemade panels will be ready, they can be folded into a separate pile and start preparing new panels. The manufactured panels should lie already without load for another day, after which they can be used for their intended purpose.

Vibratory plate manufacturing

To make homemade vibrating plate, you will need to prepare:

1. An electric motor with an eccentric of the IV-98E brand, which is the main part of the vibrating plate.
2. Steel sheet, not less than 8 mm thick, size 450x800 mm. It can be ordered at any metal warehouse.
3. Two pieces of a channel with a length of no more than 400 mm.
4. Inch pipe for the handle and two rubber bushings for its attachment.
5. From the tools you will need a welding machine, a grinder and a set of wrenches.

On the narrow sides of the slab, stepping back from the edges by 80-100 mm, make an incision with a grinder to a depth of about 5 mm. After that, bend the edges towards the notch at an angle of approximately 25 0 and weld them. Bends are needed so that the vibrating plate does not sink into the material it compresses and moves freely along its surface.

Then, across the plate at a certain distance, calculated for the fastening of the electric motor, two channels are welded with the shelves down. Through advance drilled holes in the channel, with the help of M10 bolts, an electric vibrator is attached to them.

The tube handle attaches to the vibrator through soft rubber grommets available from your auto store or hardware store in the hardware department.

Thus, you can make a lot of useful things in the household with your own hands, spending only part of the money that would have to be paid when buying finished product... You just need to make some effort and have certain skills.

A summer cottage is the territory where you can give yourself freedom to carry out numerous experiments and dream up to your heart's content. This manifests itself not only in interior design, but mainly in the design of the garden or vegetable garden. Inquisitive and inventive owners have not been guided by expensive and standard methods for arranging their plots for a long time, since there are many alternative solutions for virtually all areas of activity.

There are several types of vertical beds that optimize the use of free space. Custom designs are a great opportunity to create interesting design garden, vegetable garden, suburban area.

This type of beds in most cases is used for growing ornamental plants or herbs.

Materials for making:

The length of the drainpipes is regulated in accordance with the wishes of the owner of the site. However, cumbersome beds should not be made, as they can complicate movement across the territory.

Creating a garden bed

Stage 1. Create a container. To do this, we take a drainpipe, cut it in half lengthwise and put on special plugs on both sides.

Stage 2. We take the prepared metal holders, put them on the resulting frames for the beds.

Stage 3. We make holes in the pipe. They are made in those places where metal fasteners will be located.

Stage 4. We pass a cable or a strong rope through the holes made.

Stage 5. We fix the cable / rope with fasteners.

Stage 6. We fill the resulting beds with expanded clay and soil.

Stage 7. We plant the plants in the beds.

Stage 8. We hang the pipes to the chosen place. Sometimes a special wooden crossbar is placed for this, or rather a construction in the shape of the letter "P".

Step 9. Alternatively, you can make a special design for the pipes.

Important! A bed of drainpipes is not resistant to strong gusty winds, so you should choose a place for it that is not blown from four sides by winds. Otherwise, the frame will quickly collapse, nullifying all your efforts.

A bed made of plastic bag, is another modification of vertical beds. It is extremely compact, functional and externally interesting. You can make such a bed in a couple of hours.

Materials for making:

• durable plastic wrap;
• sewing machine;
• priming;
• seedling.

In order for the bed to turn out to be durable, it is recommended Special attention give thickness plastic film, which in this case will act as a "frame" of the structure. Minimum thickness films - 0.2 millimeters.

The process of creating a plastic bed

Step 1 . We cut out 2 rectangular film segments, the size of which corresponds to the size of the created bed. An allowance of one and a half to two centimeters should be left on each side. The recommended bed diameter is twenty centimeters.

Step 2. Sew the rectangles together, leaving only the upper part of the bag unconnected.

Step 3. Sew a handle to the future garden bed, the strength of which will support the weight of the bag filled with soil. It should also be borne in mind that when watering, the weight will increase.

Step 4. Fill the bag with fertilized soil.

Step 5. We make horizontal cuts on the bag in twenty centimeters increments. They are necessary in order to plant seedlings in the garden bed.

Step 6. We plant seedlings.

Step 7. Water the soil regularly and add the necessary fertilizers.

With these simple steps, you can get a cheap and useful garden bed.

An integral part of every summer cottage is a compost heap. This is the place where all kinds of biochemical reactions take place that ensure the creation of fertilizers.

To create fertilizers that will satisfy all the requirements for them, you should carefully consider several key steps: creating a container and directly correct manufacturing the compost itself. Let's talk about each of them in more detail.

Stage 1. Take eight support posts of the same length.

Stage 2. We treat the lower part of the wooden posts with engine oil or tar.

Stage 3. We dig the posts into the ground so that they are reliable and stable. If compost bin will be located next to the fence, then 4 posts (that is, one side) can be attached to the fence. This will avoid having to dig 4 holes.

Stage 4. Between each two adjacent posts we nail the crossbeams so that we end up with three independent sections. Be sure to leave slots that will function as ventilation holes.

Stage 5. In two sections, we nail the boards horizontally to half the height of the posts. In these places, it is planned to create two small doors.

Step 6. The remaining section will big door so only one plank should be nailed down. It should be located at the very bottom in a horizontal position, that is, like a regular crossbar.

Stage 7. Installing the covers. You can use one large solid board for this.

Stage 8. Install the pre-prepared doors.

Stage 9. We provide doors with handles and latches.

Stage 10. We process wood using special impregnations.

Step 11. Paint the box any color that suits your preferences.

Many gardeners mistakenly believe that any component can be dumped into a compost heap. In fact, to create the right biofertilizer, you need to carefully select the "ingredients".

Among the mandatory components compost heap the following components:

• peat;
• ash;
• needles;
• tree branches;
• leaves;
• hay or grass;
• wood ash;
• plant roots;
• raw vegetables and fruits, etc.

All elements are randomly mixed on the heap. To speed up chemical reactions it is recommended to cover the pile with a tarp (this is especially true in the absence of a box).

Trips to the country house with the family involve the presence of entertainment elements on the site that will delight children. The most common way to keep young summer residents busy is with a swing.

Building a swing yourself is not an easy task, but quite doable. Of course, you can always take a stick, tie it with a rope and hang the structure on a tree, but this can hardly be called a full swing. True craftsmen prefer to build comfortable structures with a comfortable seating position.

Constructive components:

• two logs;
• strong rope.

Indicators:

• diameter of logs - 85 mm;
• length of logs - 700 mm;
• distance between ropes - 500 mm.

Making a swing

Stage 1. We stretch the ropes between the logs.

Stage 2. We wrap each log with ropes.

Stage 3. We release the ropes out.

Stage 4. We tighten the ropes by 3 knots.

Stage 5. We fix the swing on the tree.

Important: such a swing is designed for only one person.

Garden path from scrap materials

There are several types of garden paths that you can easily do with your own hands.

Step 1. Remove the sidewall from the tire using a knife or saw.

Step 2. Cut the tires.

Step 3. We line the space with grooved stripes.

Step 4. We paint the path with paint.

Step 5. Sprinkle with stone chips.

This is an economical option for those who do not want to rack their brains and spend time on a full-fledged garden path. The tire track is usually used for vegetable gardens, as it easily fits into the ground.

Stage 1. We paint the corks in different colors.

Stage 2. We dig a small trench.

Stage 3. We drive in supports to strengthen the future track.

Stage 4. We build the formwork using boards.

Stage 5. Install spacers along the edges of the trench.

Stage 6. We place crushed stone deep into the trench and carefully tamp it.

Stage 7. We make a mortar from sand, cement, glue and water.

Stage 8. Pour the solution into the trench.

Stage 9. Press in the plugs in random order. Even multi-colored stripes look interesting.

These are the simplest and quick ways make a garden path without purchasing expensive materials.

DIY tools

The expression "everything will come in handy on the farm" turns out to be as relevant as possible when it comes about canisters. From this plastic container, you can make a large number of irreplaceable tools that are actively used in the process of summer cottage work.

To make this tool, we only need a sharp knife and the container itself.

Stage 1. Cut off the bottom of the canister.

Stage 2. We mark the cut line for the scoop on the container so that the handle from the canister is the handle of the future tool.

Stage 3. Cut off excess material.

As a result of these simple steps, we get an excellent scoop with a comfortable handle.

Materials:

Manufacturing

Stage 1. Carefully wash the canister so that there is no smell left in it.

Stage 2. We cut the canister vertically into two parts.

Stage 3. We make a groove on the plank using a woodworking machine.

Stage 4. Apply glue to the plywood and insert into the bottom of the canister.

Stage 5. We paint the resulting shelf with a spray can.

Of course, such a structure will not withstand a lot of weight, but it is quite suitable for storing small parts.

Materials:

• 40 cans;
• scissors;
• rope;
• paper;
• marker.

Stage 1. We pierce the upper part of the cans with a knife.

Stage 2. We make a stencil out of paper.

Stage 3. We apply it to the canister, outline it with a marker.

Step 4. Cut out large holes with scissors.

Stage 5. We put the prepared cans in several rows, tying each row by prying the rope under the handles of the containers.

Stage 6. We tie all the rows around the perimeter for greater strength.

Stage 7. If the cabinet is planned to lean against the wall, then we drill it to the surface.

Stage 8. We put heavy objects in the bottom row - stones or bricks.

The result is a fairly spacious and functional rack that will help get rid of the issue of storing many small parts.

Be resourceful and courageous in bringing your ideas to life. Good luck!

Video - DIY homemade products for giving

Video - We do it ourselves for a summer residence