Round bench around a tree. Do-it-yourself wooden benches: photos, drawings of a circular bench

Today we are talking about benches for rest. We are no longer surprised when they are not in the most needed places! Could they be outrageously expensive? No. Moreover, they are not difficult to make with your own hands.

As a rule, wooden benches are made in the form of a hexagon. They can be with or without a back. It is better that the trunk diameter reaches more than 500 millimeters. If the tree is still growing, it is worth considering what diameter it will be in the future. To make a bench around the oaks, you need a larger one. The product can be made in the form of an octagon.

Tools and materials

To make a bench with your own hands you will need the following materials:
● screws;
● planed lumber (section is 70x70 millimeters) - 4 pieces of 2 meters each, length - 480 millimeters;
● planed material with a section of 45x70 millimeters - 9 meters;
● terraced boards with a section of 22x95 millimeters - 30 meters;
● corners - 8 pieces.

Do not forget about cement - you will need about 2 bags and materials such as varnish, paint, wood impregnation. It is not necessary to paint the finished bench.

Planed lumber will be required to make a bench around a tree

Wood also has special requirements. To make a bench, you will have to find a tree that is highly resistant to weathering. It can be different types tropical wood. If the rocks are not so resistant, they will have to be treated with special impregnations.

For the manufacture of benches, pine is often used, made under pressure. If there are knots on the rock, this is not an obstacle for impregnation treatment. Any additional processing not required.

Step-by-step instruction

Making drawings
The bench is usually made of 6 parts of equal size, in the photo it looks very original. First you need to determine the diameter of the tree trunk. If it is young, it is necessary to add 30 centimeters, if an adult - 15. To determine the length of the short part individual element divide by 4. Mark the length on a measuring stick and saw off the edges at a 30 degree angle.

Drawing of a bench around a tree

Product size
To make the bench, complete the starting board template based on the measurements you found with the corners sawn off at 30 degrees. Next, lay 3 boards parallel to the board and separate them with centimeter spacers. Reiki applied to wooden elements(taking into account the angle of 30 degrees of the initial board). Put a mark.

To make a bench, you need to complete the template of the initial board, based on the identified dimensions with corners

sawing boards
The cut should be done like this. Set the saw to 30 degrees. Saw the 3 boards marked earlier to length with opposite angles at both ends.

It is necessary to cut the boards according to the marks

Assembly
Now you need to assemble the hexagon. This is done on a flat surface, do not forget to add centimeter spacers. Start from the inside of the seat. It is important to clarify whether the corners fit.

legs
Making the legs is pretty easy. They include an inner and outer leg, located between 2 supports. It will take 12 elements to assemble 6 frames. Craft 12 supports. The end of each of them should be sawn off at an angle of 30 degrees.

Bolt holes
Although they are not visible in the photo, the recesses for the bolts should be prepared in advance. Take a drill and make holes, the indent from the front edge of the outer support should be 5 centimeters. Make a mark on the vertical flat side at the indicated location. Repeat the procedure on the other side of the support.

Leg pinning
Fasten the supports and legs with your hands. Place the bolts into the holes. Use for tightening bolts with nut and washer wrench.

Section Assembly
Place your feet vertically on a flat surface with your hands. Secure using clamps. At the top of the leg of the assembly between the boards, install spacers. The edge of the board should be on half of the leg of the assembly. The boards are fixed to the legs with self-tapping screws. Fasten the legs to 4 sections. As a result, 2 groups should come out, each with 2 sections. Install the last section. On opposite sides of the trunk, place 2 groups. Fasten them with the remaining 2 sections.

End of work
Align the item. To do this, using a spatula, dig the legs into the ground. If necessary, cut and put the backs, that's all, in front of you is an almost finished bench that will look good on a photo in a family album. It remains only to make an apron.

To do this, measure the distance between the long support points in the sections. Make 6 bars at an angle of 30 degrees. Fasten the bar using a clamp. Next, you should drill holes, mount to the outer leg. All sections should be processed in the same way. The final stage is the grinding of roughness. The result is a very comfortable bench.

The final step in building a bench around a tree is sanding the roughness

● If you deviate a little from the size of the bars and support boards, there is nothing to worry about, just the design of the bench will change a little, it will still look spectacular. However, the outer frame must still be in the shape of a square. The dimensions of the short sides are decisive, and the thickness of the timber, multiplied by 2, should be added to the long ones.

● Water is able to penetrate into the wood through the lower parts of the legs, so it is recommended to treat them with azure or special oil. A wax-like composition gives a good effect; a bench soaked with this product will look great.

● If you are going to make a backrest, you should foresee 4 components, 4 backrests and loose seats. As a result, when assembled, you get an octagon.

● Load capacity finished product sufficient. If you think that the load will be large, install additional supports in the inner square. But if the ground is uneven, installation can cause problems.

● If the bench elements have been treated under pressure, the product will be resistant to sunlight and adverse weather conditions. In this case, the tree should not be painted, the sections are not subjected to additional processing.

● It is important to determine in advance where the bench will be placed. On the ground, before installation, markings are made in the form of a regular 6-pointed star or octagon. It is very easy to draw a star - superimpose 2 equilateral triangles on top of each other.

Do-it-yourself bench around a tree (video)

A bench around a tree, as in the photo in this article, can be done by almost everyone, the main thing is to act in stages, following the instructions. It is important to choose the right wood, it must be durable and not be afraid of sunlight and bad weather. Everyone can have their own bench option. Most often, 6-angled shapes are used, but if the tree is impressive, then it is better to stop at an octagon. Backrests are optional.

Varieties of benches with a tree (video)

Many people lament wildly that their garden plots are not gentrified enough. Spreading oaks create coolness, but it is a pity to use them for hammering nails. Therefore, today I propose to watch a master class on the topic of a chic comfortable bench around a tree with your own hands.

We take old boards or slats and take measurements around the selected tree. Please note that the bench will dig in, so try to choose the most comfortable size.

Let's take wooden planks and measure the dimensions we need. Try to do it carefully, it is best to use special tools for the correct size.

When you are wondering: how to build a bench with a backrest with your own hands, then you should not put anything aside. Therefore, after measurements, it is urgent to cut and drill holes to connect the back to the main part of the bench.

First, we begin to assemble the bench on the floor to fit it up to the right sizes. Carefully assemble the bench in a circle, assemble it as accurately as possible, but so that you can disassemble it.

We twist the bench, trying to tighten the bolts as much as possible. After all, the bench can also be used as a couch or even as sleeping place during the daytime.

We assemble our bench near the selected tree and diligently dig it around the entire perimeter of our tree.

It remains only to screw the back into place and our wonderful bench is ready.

When the task arises - how to build a bench with your own hands, you do not need to skimp on materials, it is best to use a well-hardened tree that will survive many summer seasons, including winter period inaction.

In the kitchen, we tend to spend a lot of personal time. So why not make our stay there more enjoyable and comfortable? We found in the open spaces of Aliexpress useful things for the kitchen which will definitely be of interest to everyone. And they all cost no more than 200 rubles, so in addition it will not be expensive for your budget.

To build a bench around a tree, you need to choose specially impregnated and thermally modified pine. Let's get started.

1. Make a bench template.

2. Create a template.

The bench will consist of six parts of the same size.Measure the diameter of the tree.Add 15 cm for a mature tree and 30 cm for a young tree to allow the tree to grow.Divide the sum by 4 to find the length of the short side of the individual piece. Mark the amount received on the measuring rod and saw off the edges of the rail at 30 degrees.

3. The size of the part of the bench.

Make a template for the first board of the bench, according to the previous dimensions, with sawn-off corners at 30 degrees.Lay three boards parallel to it, separating them with centimetergaskets as shown.Attach the slats to the boards, taking into account the 30 degree angle of the first board. Make a mark.

4. Saw the boards according to the marks.

Set the saw to 30 degrees.Cut the three bench boards you marked in the previous step to length with opposite angles on both ends.Repeat steps 3 and 4 and make the remaining 5 parts of the bench.

5. Lay out all the parts of the bench.

Assemble the pieces into a bench hexagonal shape on a flat surface using, adding centimeterspacers between them as shown in the picture.Beginning with inner board seats.Check how the corners are applied.

6. Blanks for bench legs.

The legs consist of an outer and an inner leg sandwiched between two supports.Cut out 12 legs in order to assemble 6 frames to the height of the bench.(If the ground around the tree is uneven, make the legs longer, so that you can then level the bench by digging the soil under them).Cut out 12 supports. Saw off the end of each support at an angle of 30 degrees. This will be needed further to attach the apron.

7. Mark and drill holes for the bolts.

Using a drill, drill holes 5 cm from the front edge of the outer support and make a mark on the vertical flat side of the support at this location.Repeat for the other side of the support.See drawing.

8. Fasten the legs and supports together.

Insert bolts into each hole you made in the last step.Use an adjustable wrench to tighten all bolts with washer and nut.Repeat these steps for the remaining five assembled legs.

9. Beginning of the assembly of sections

Stand with your feet upright on a flat surface, secure everything with clamps.Place spacers between boards, at the top of the leg assembly. The edge of the board should lie halfwayassembly legs. Fasten the boards to the legs with self-tapping screws. Fasten the legs to 4 sections. As it shown on the picture. You should have 2 groups of 2 sections.

10. Attach the last section.

Place two groups on opposite sides of the tree. Connect these groups with the remaining 2 sections.

11. Level the bench.

Using a spatula, deepen the legs of the bench to level the surface.

12. Cut and install backrests.

13. Cut and install the apron.

Measure the distance between the long support points for each section.Cut out six pieces with 30 degree edges.Fasten the bar with a clamp.Drill pilot holes and attach it to the outer leg. Repeat these steps for the rest of the sections. Finish the bench by sanding any rough edges.

Here's what we got. Comfortable and simple bench. In hot weather, you can hide under a tree with the whole family. You will enjoy relaxing with your favorite book throughout the summer.

A flower bed around a tree looks spectacular, and for inexperienced inhabitants, such an idea seems simple and easy to implement. However, when creating it, it is necessary to take into account the compatibility of the type of tree and the plants growing under it. ornamental plants. There are species that do not tolerate any vegetation in the zone trunk circle. Such individual farmers include birch, willow, spruce, Walnut, larch, maple, irga, thuja and pine.

These tree species have a surface root system and will oppress any closely growing plant, competing for nutrients and moisture. It is better to arrange the trunk circles of this group of trees in some other way than to create a flower garden doomed to death. Lawn grass will grow well under such trees.

However, with a strong desire, in such cases it is possible to create some elevation from the soil mixture in the form of a podium, the design of such a flower garden will be discussed in more detail below. Hazel and chestnut produce substances that are toxic to other plants.

Apple, pear, mountain ash, linden, oak, poplar, ash and fir easily let grassy neighbors under their crown, allowing you to create luxurious compositions.

Regardless of the type of tree, when planning and arranging a flower garden, you will need to take into account some more features of such a design project. Flower plants are selected only shade-tolerant and resistant to uneven moisture. These plants include all types of hosta, most groundcovers, dwarf conifers, some perennials (bergenia, periwinkle, Volzhanka, lily of the valley, saxifrage, lungwort, snowdrop, ferns, foxglove, violet, raven, slipper, Goryanka, anemone) and bulbous.

Usually flowering shade-loving plants occurs in early spring, when the crown still lets in enough sunlight. Although the main decoration of the shady flower bed is decorative foliage.

Before planting flowers around a tree, you need to properly prepare the place. Removed first upper layer soil. This is done very carefully so as not to damage the root system of the tree. In some cases, planting is carried out in "pockets" between thick root branches. The bottom of the dug hole should be lined with non-woven material to protect the root system and restrain its growth.

Next, be sure to lay out a drainage layer of pebbles, broken bricks or crushed stone 10 cm thick. The removed soil is replaced with a nutrient mixture of compost, soddy soil and peat with complex mineral fertilizers. In the presence of rhizomes of weeds, it is recommended to carefully select them. Seedlings are planted in moist soil. Free areas are mulched with sawdust or wood chips. Complex flower beds of plants with different habits are made according to the principle: the higher, the closer to the trunk.

The shape of the flower bed can be either round or asymmetrical. So that the soil does not spill out and is not washed out during irrigation, the border of the flower garden must be marked using decorative stones or a border made of wood or plastic. The arrangement of flowers in a flower bed does not have to follow any scheme; chaotic compositions look interesting and natural.

DIY raised flower bed under a tree

While creating flower bed under unfavorable trees, difficulties may arise due to the many roots penetrating the topsoil in the near-stem circle. Perennials with deep-penetrating roots cannot be used for the composition; it is much more profitable to plant annuals (ageratum, begonia, amaranth, annual asters, succession, carnation, gazania, lobelia, verbena).

To increase space for root growth flower crops, you can design a raised or multi-tiered flower bed on the site under the tree. To make the side of an asymmetric flower bed, you can use wooden slats and plastic bottles, and for a round one, bricks, old tires and a plastic curb are suitable. Easy and quick to make a square wooden box from boards. It is important that the height of the soil covering the tree trunk does not exceed 10 cm. If the root neck is somewhat raised above the soil level, then the soil can be covered even higher.

You can make a flower bed of logs in an original and low-cost way. To do this, thick branches or the trunk of an old tree are sawn into cylinders 20–30 cm long, which, in turn, are split into halves. In construction stores you can buy ready-made borders. Harvested logs are treated with an antiseptic and dried.

Then the geotextile tape is cut off, to which the logs are attached with staples or nails. Geotextiles will protect the tree from moisture and extend the life of the curb. At the next stage, the finished border is buried in the soil around the tree and fixed with steel rods. After layout nonwoven fabric, drainage and backfilling devices, the flower bed is ready for planting.

Resting place under the tree: bench and table

The trunk circle zone can be not only beautiful, but also useful. A round, hexagonal or square bench around a tree trunk and a table will complement a well-maintained garden without requiring highlighting. separate place. The bench and table can have a different design, differing in style and complexity of execution.

Most often garden furniture suit under birch, chestnut, walnut and willow. The main rule: buildings should not fit snugly against the trunk, be sure to leave room for growth. Wood is more acceptable as a material, but metal and stone are also used.

Of the breeds, it is preferable to choose larch - the record holder for durability and resistance to external influence. Less expensive options: pine, acacia, spruce and cherry.

The most common garden bench design is hexagonal, backless or high backed.

To make a simple bench with your own hands, you will need to do the following work:

preparation of the material (wide boards for the seat, 12 bars about half a meter long for the legs, 6 planks for the back, small blanks for joining and self-tapping screws);
section size determination (largest side = trunk diameter + 15 cm, smallest inner side= length of longest side / 1.75);
cutting the parts that make up each of the 6 sections, while the cut angle should be 30º;
processing of all parts and places of cuts with an antiseptic, followed by drying;
assembly of sections, consisting in fixing the seat slats to meter-long transverse boards;
assembling the legs, which consists in fixing the outer and inner legs to a common wide bar using self-tapping screws, as a result, 6 prefabricated elements should be obtained;
fastening adjacent sections to the legs, in this case two parts of 3 sections each should be obtained;
fastening parts around a tree;
installation of back parts;
the finished structure is coated with a wax-containing impregnation.

The table around the tree of the simplest design consists of metal frame with bars fixed around the trunk, and a tabletop consisting of several sections. The connection of the frame and the tabletop is carried out by means of wooden planks.

How to arrange a gazebo around a tree?

If the creation of a flower bed and a bench seems too simple and unoriginal, you can think about building something larger, for example, a gazebo or a cozy seating area.

A plot under a tree can be a great place for an open garden gazebo. At the same time, the crown of the tree will serve as a natural canopy from the scorching sun, and if the shade does not seem enough, then you can plant actinidia - a fruit-bearing vine weaving along the branches with large leaves protecting from the sun and light summer rain.

A garden gazebo around a tree serves as a comfortable place not only for outdoor activities and communication, but can also be a great corner for sleeping and reading. Its design can be very different, the design depends on general style garden. A simplified solution is a small wooden deck podium.

If you add a low fence to the raised flooring, you get a fairly simple open gazebo.

For those who want to create more monumental structures and, so to speak, rise above the ground, buildings on high wooden racks can be advised. They look quite impressive, and allow you to enjoy the picturesque view of the site.

All considered design ideas design of the site in the zone of the near-trunk circle can be actively used on any garden plot, adding new details and modifying the proposed appearance of the building. In addition to the options presented, the area around the tree can be decorated with pebbles, sown with grass or mulched with wood chips. In some design styles such minimalism is the best choice.

Do-it-yourself log bench for the garden

First of all, you need to decide on the place where you want to put the bench.

It is best to choose a shade, under a tree or a canopy near the house, you can also make a canopy.

Also think about what you will see when sitting on a bench: it is better if it is a pond, a garden, the front entrance of a house or a playground, a sandbox.

Now we measure the length of the future bench. As for other parameters, everything here is standard for all benches: seat height - 40-50 cm, back height - 35-50 cm, seat width - 50-55 cm.

Next, decide what materials you have to create a bench (boards, logs, stumps), and what size they are. Based on this, you can decide which of the shops below you can make.

First, it’s worth saying how to treat the surfaces so that there is no resin on them.

There are two simple options:

It is also necessary to remove knots, and the surfaces on which they will sit and lean should be processed grinder(if not, then with a simple sandpaper).

For the durability of the bench, cover it with a good antiseptic and protective coating.

Do you want to learn how to make a gazebo with your own hands?

Or read about sealing cracks in a log house.

Creating a simple bench from logs

This is a very simple option. garden bench from a log.

To create it you need:

So, after the preparatory work described above, we proceed directly to the manufacture of the bench. Let's start with the seat.

Sawing big log and process the cut points. One half is the seat.

From the other half we cut off the rounding, leaving a board 10 centimeters wide. This is the back.

Then we put them on their side and cut out the v-shaped cutouts in order to put the seat in them.

Now we attach the seat to the legs with self-tapping screws.

It remains only to attach the back. Let's start with the pegs on which it will hold. We attach them with one self-tapping screw to the back of the seat next to the leg, and with the second - to the protruding part of this leg. Can be done with or without tilt.

The same with the second peg. We fasten the back to them. The bench is ready!

Step-by-step instruction

Making drawings

The bench is usually made of 6 parts of equal size, in the photo it looks very original. First you need to determine the diameter of the tree trunk. If it is young, you need to add 30 centimeters, if an adult - 15. To determine the length of the short part of an individual element, divide the sum by 4. Mark the length on a measuring stick and saw off the edges at an angle of 30 degrees.

Product size

To make the bench, complete the starting board template based on the measurements you found with the corners sawn off at 30 degrees. Next, lay 3 boards parallel to the board and separate them with centimeter spacers. Reiki is applied to wooden elements (taking into account the angle of 30 degrees of the initial board). Put a mark.

sawing boards

The cut should be done like this. Set the saw to 30 degrees. Saw the 3 boards marked earlier to length with opposite angles at both ends.

Assembly

Now you need to assemble a hexagon with your own hands. This is done on a flat surface, do not forget to add centimeter pads. Start from the inside of the seat. It is important to clarify whether the corners fit.

legs

Making the legs is pretty easy. They include an inner and outer leg, located between 2 supports. It will take 12 elements to assemble 6 frames. Craft 12 supports. The end of each of them should be sawn off at an angle of 30 degrees.

Bolt holes

Although they are not visible in the photo, the recesses for the bolts should be prepared in advance. Take a drill and make holes, the indent from the front edge of the outer support should be 5 centimeters. Make a mark on the vertical flat side at the indicated location. Repeat the procedure on the other side of the support.

Leg pinning

Fasten the supports and legs with your hands. Place the bolts into the holes. Use an adjustable wrench to tighten the bolts with a nut and washer.

Section Assembly

Place your feet vertically on a flat surface with your hands. Secure using clamps. At the top of the leg of the assembly between the boards, install spacers. The edge of the board should be on half of the leg of the assembly. The boards are fixed to the legs with self-tapping screws. Fasten the legs to 4 sections. As a result, 2 groups should come out, each with 2 sections. Install the last section. On opposite sides of the trunk, place 2 groups. Fasten them with the remaining 2 sections.

End of work

Align the item. To do this, using a spatula, dig the legs into the ground. If necessary, cut and put the backs, that's all, in front of you is an almost finished bench that will look good on a photo in a family album. It remains only to make an apron.

If you deviate a little from the size of the bars and support boards, there is nothing to worry about, just the design of the bench will change a little, it will still look spectacular in the photo. However, the outer frame must still be in the shape of a square. The dimensions of the short sides are decisive, and the thickness of the timber, multiplied by 2, should be added to the long ones.
Water is able to penetrate the tree through the lower parts of the legs, so it is recommended to treat them with azure or special oil. A wax-like composition gives a good effect; in the photo, a bench soaked with this product will look great.
If you are going to make a back, you should foresee 4 components, 4 backs and loose seats. As a result, when assembled, you get an octagon.
The carrying capacity of the finished product is sufficient. If you think that the load will be large, install additional supports in the inner square. But if the ground is uneven, installation can cause problems.
If the elements of the bench were processed under pressure, the product will be resistant to sunlight and adverse weather conditions. In this case, the tree should not be painted, the sections are not subjected to additional processing.
It is recommended to lean back a little. The design of the legs with two points of support on the seat allows you to give the bench stability.
It is important to determine in advance where the bench will be placed. On the ground, before installation, markings are made in the form of a regular 6-pointed star or octagon. It is very simple to draw a star - superimpose 2 equilateral triangles on top of each other.

Round benches around trees

The trunk of a tree is round, so it makes sense that many benches around trees are also made round. This bench, which offers a wonderful view, is a real decoration of the deck. The slats from which it is made echo the slats of the fence.

Round bench around a tree with a great view

This bench from Forever Redwood has a comfortable back, which is very pleasant to lean on while you are in the clouds. The bench is made of superbly sanded mahogany and the sealant guarantees weather resistance.

Round bench around mahogany tree

Carved bench around a tree from Benches.co.uk, featured on the actual top photo full of personality. The design with round holes at the top of the back is reminiscent of the Midcentury style, and the wooden slats radiate from the center of the bench. Absolutely great product!

What could be better than handles that allow you to designate personal space, especially if the bench is located in public place! And again, mahogany in the Luna model from Forever Redwood. Please note that this bench is available in three standard sizes.

Tree Bench by Forever Redwood

Hexagonal benches around trees

Round shapes are great, but add a few corners and you'll end up with an image that embraces both the hexagon itself and the space behind it. This bench around the tree on the deck creates clean lines.

Bench around a tree on a wooden deck

Benches around trees can be placed on wooden decks, green lawns, in stone patios. It cannot be denied that this bench in gray tone looks very modern

Gray hexagonal bench around a tree

The bench in the photo below is truly the centerpiece of a pebbly garden full of treasures. Notice how well the warm tone of the shop harmonizes with warm color brick gardening.

Hexagonal bench in the yard covered with pebbles

Below is a hexagonal wooden model Coral Coast Fillmore by Hayneedle, which provides back support and weather-resistant cedar adds golden tones to the yard.

Wooden bench from Hayneedle

Like the previous model, the bench from Brookstone encircles the tree of your choice:

Hexagonal bench from Brookstone

creative solutions

Today's review ends with benches that defy mediocrity.

To create more unusual look it is worth abandoning the bench, located completely around the tree, and choose an L-shape, as is done in the photo below:

Modern L-Shaped Tree Bench

For variety, you can choose a semi-circular bench, especially in the case when installing a bench completely around the tree is not possible. The photo below shows the Miramar bench from Forever Redwood, which is available in three available sizes.

Semi-circular bench from Forever Redwood

Isn't it true that these creative ideas for garden benches from BHG, simply fabulous? The photo on the left shows a painted bench, in which each plank has its own shade. To the right is a bench floral design lined with mosaics.

Garden Creativity by BHG

Sleek and modern appearance square bench in the photo below echoes the shape of square bright ottomans that add zest modern courtyard at home.

Contemporary square bench around a tree

No tree is too thin for a bench! For a strong effect, leave a small hole in the center of the bench. Modern and stunning, don't you think?

Square bench around a thin tree

Leave extra space in the center of the bench, fill it with soil and arrange a flower bed. Why not make the most of the space?

Flower bed in a bench around a tree

This unusual bench near a tree looks more like a deck chair. And there is nothing wrong with that! Attractive pillows complete the casual look.

Bench-chaise longue in a beautiful patio

Last but not least. Several creative solutions from Mono Goen, which will be able to transform the interior space.

All it takes is one or two indoor plants. Are you looking for a solution with a bench, or interesting option with a table and a chair, the ideas presented in the photos below will help you create an original interior.

Unusual seating by Mono Goen

Connoisseurs of natural harmony strive to turn a place in the shade of a fragrant linden, mighty oak or compact chestnut tree into a cozy corner of relaxation and solitude.

For some gardeners optimal solution will put an ordinary bench under the tree, while others are looking for original ideas.

In any case, a lawn under a tree can not only perform an aesthetic function, but also carry a functional load, serving as a place for a family tea party, an evening conversation with friends, or lonely thought.

Create a flower bed under a tree

A flower bed around a tree looks spectacular, and for inexperienced inhabitants, such an idea seems simple and easy to implement. However, when creating it, it is necessary to take into account the compatibility of the type of tree and ornamental plants growing under it. There are species that do not tolerate any vegetation in the zone of the near-trunk circle. Such individual farmers include birch, willow, spruce, walnut, larch, maple, irga, thuja and pine.

These tree species have a shallow root system and will overwhelm any closely growing plant, competing for nutrients and moisture. It is better to arrange the trunk circles of this group of trees in some other way than to create a flower garden doomed to death. Lawn grass will grow well under such trees.

Apple, pear, mountain ash, linden, oak, poplar, ash and fir easily let grassy neighbors under their crown, allowing you to create luxurious compositions.

As a rule, flowering of shade-loving plants occurs in early spring, when the crown still lets in enough sunlight. Although the main decoration of the shady flower bed is decorative foliage.

Before planting flowers around a tree, you need to properly prepare the place. First, the top layer of soil is removed. This is done very carefully so as not to damage the root system of the tree. In some cases, planting is carried out in "pockets" between thick root branches. The bottom of the dug hole should be lined with non-woven material to protect the root system and restrain its growth.

The shape of the flower bed can be either round or asymmetrical. So that the soil does not spill out and does not wash out during irrigation, the border of the flower garden must be marked using decorative stones or a border made of wood or plastic. The arrangement of flowers in a flower bed does not have to follow any scheme; chaotic compositions look interesting and natural.

DIY raised flower bed under a tree

When creating a flower bed under unfavorable trees, difficulties can arise due to the many roots penetrating the top layer of soil in the near-stem circle. Perennials with deep-penetrating roots cannot be used for the composition; it is much more profitable to plant annuals (ageratum, begonia, amaranth, annual asters, succession, carnation, gazania, lobelia, verbena).

To increase the space for the growth of the roots of flower crops, you can design a raised or multi-tiered flower bed in the area under the tree. To make the side of an asymmetric flower bed, you can use wooden slats and plastic bottles, and for a round one, bricks, old tires and a plastic border are suitable. It is easy and quick to make a square wooden box from planks. It is important that the height of the soil covering the tree trunk does not exceed 10 cm. If the root neck is somewhat raised above the soil level, then the soil can be covered even higher.

Then the geotextile tape is cut off, to which the logs are attached with staples or nails. Geotextiles will protect the tree from moisture and extend the life of the curb. At the next stage, the finished border is buried in the soil around the tree and fixed with steel rods. After laying out the non-woven material, draining and backfilling the soil, the flower bed is ready for planting.

Resting place under the tree: bench and table

The trunk circle zone can be not only beautiful, but also useful. A round, hexagonal or square bench around a tree trunk and a table will successfully complement a well-groomed garden without requiring a separate place. The bench and table can have a different design, differing in style and complexity of execution.

Most often, garden furniture is arranged under birch, chestnut, walnut and willow. The main rule: buildings should not fit snugly against the trunk, be sure to leave room for growth. Wood is more acceptable as a material, but metal and stone are also used.

Of the breeds, it is preferable to choose larch - the record holder for durability and resistance to external influences. Less expensive options: pine, acacia, spruce and cherry.

The most common garden bench design is hexagonal, backless or high backed.

To make a simple bench with your own hands, you will need to do the following work:

preparation of the material (wide boards for the seat, 12 bars about half a meter long for the legs, 6 planks for the back, small blanks for joining and self-tapping screws);
section size determination (largest side = trunk diameter + 15 cm, smallest inner side = longest side length / 1.75);
cutting the parts that make up each of the 6 sections, while the cut angle should be 30º;
processing of all parts and places of cuts with an antiseptic, followed by drying;
assembly of sections, consisting in fixing the seat slats to meter-long transverse boards;
assembling the legs, which consists in fixing the outer and inner legs to a common wide bar using self-tapping screws, as a result, 6 prefabricated elements should be obtained;
fastening adjacent sections to the legs, in this case two parts of 3 sections each should be obtained;
fastening parts around a tree;
installation of back parts;
the finished structure is coated with a wax-containing impregnation.

A table around a tree of the simplest design consists of a metal frame with bars fixed around the trunk, and a tabletop consisting of several sections. The connection of the frame and the tabletop is carried out by means of wooden planks.

How to arrange a gazebo around a tree?

If the creation of a flower bed and a bench seems too simple and unoriginal, you can think about building something larger, for example, a gazebo or a cozy seating area.

A plot under a tree can be a great place for an outdoor garden gazebo. At the same time, the crown of the tree will serve as a natural canopy from the scorching sun, and if the shade does not seem enough, then you can plant actinidia - a fruit-bearing vine weaving along the branches with large leaves that protect from the sun and light summer rain.

A garden gazebo around a tree serves as a comfortable place not only for outdoor activities and communication, but can also be a great corner for sleeping and reading. Its design can be very different, the design depends on the overall style of the garden. A simplified solution is a small wooden deck podium.

If you add a low fence to the raised flooring, you get a fairly simple open gazebo.

All considered design ideas for decorating a plot in the area of the near-trunk circle can be actively applied to any garden plot, adding new details and modifying the proposed appearance of the building. In addition to the options presented, the area around the tree can be decorated with pebbles, sown with grass or mulched with wood chips. In some design styles, this minimalism is the best choice.