DIY table lamp bases. How to make a table lamp with your own hands? Making a lampshade with children

Decorating a house on your own is a favorite pastime of many hostesses, this article reveals how to make a lamp with your own hands. You can revive the interior of a living room, bedroom or hallway with the help of improvised means, only by changing the shade of a chandelier, floor lamp or table lamp. DIY lamp shades can be used not only in residential interior, but also in the halls of cafes, pubs, pizzerias.

The choice of materials and lamps for the lamp

Products made for children's rooms should be made of natural non-toxic materials and painted with ecological paints.

When manufacturing, you should also remember fire safety, therefore, lampshades made of flammable materials made of paper, plastic, feathers or thread should only be used with lamps that have a low heating temperature.

You need to use LED or fluorescent lamps. They have several advantages:

long service life;
minimum heating of the base from the glass part;
light has three shades: warm, cold, neutral.

In addition, such lamps are also called energy-saving; their only drawback is their high cost.

It is also advisable that the connection of the wire to the base is made by a specialist. You do not need to try to perform this operation yourself, as this can lead to undesirable consequences. It is more convenient to decorate an existing shade frame or make it from durable and not very heavy materials.

The following materials are used to create lamps: scissors, an assembly knife, fishing line, wire, pliers, a hot gun, in some cases it can be replaced with super glue. They must be used by an adult; it is unacceptable to involve a child in gluing. Since in one case he will receive a burn, and in the other he may glue his fingers or stick to the details of the future product.

What can you make a plafond from?

Many craftsmen make lamps from completely unnecessary materials:

made of plastic or glass bottles;
newspapers, tissue or colored paper;
artificial or natural threads;
dried branches unusual shape;
disposable spoons;
old disks.

Plastic lamp

From plastic containers of different sizes, a homemade chandelier is easily obtained.

For the base, you need to take a 5 liter bottle. The bottom is cut off from it. Then circles with a diameter of 1.5 cm are drawn on the surface. They need to be cut out with an assembly knife or small scissors.
The bottom of the bottles for decoration is cut off and the entire surface is cut with scissors into strips 0.5 - 1 cm wide, then the workpiece is heated over the lighted burner. Under the influence of heat, the stripes will acquire a chaotic appearance.
Then workpieces are inserted into a 5-liter container with holes, and with inside lids are screwed on. Then a wire is threaded through a large neck and a plafond is installed. For such a shade, you need to use an energy-saving lamp.
In some interiors, you can find a fancy lamp made on the basis of an ordinary hanger or a straw hat. In general, nothing can limit the scope of imagination of both home craftsmen and professional designers.

Glass bottle shade

A very interesting version of a homemade chandelier is obtained from glass bottles. They are used to decorate the halls of catering establishments. Also this a good option for a kitchen in a residential building or apartment. This can be a shade, consisting of one or several bottles, from which the bottom is cut off. You can do this yourself, but it is better to use the services of a workshop where glass and mirrors are cut.

How to use threads

For a lampshade made of threads or ribbons you will need: a ready-made frame made of strong wire, threads different color, scissors, glue.

The frame consists of two rings connected by metal segments. You can make it yourself from strong wire.
One color or several shades of thread are required.
A thread is fixed on the lower part, then it must be pulled through the upper ring, lowered down and thrown over the lower ring. It is necessary to ensure that the thread is taut and the turns fit snugly against each other. As soon as the thread ends, you need to attach the next piece to the bottom ring.
Carefully cut off the remaining threads and glue them on the back.

Lamp spoons

You can make a multi-tiered, colored lamp from ordinary disposable spoons.

It is necessary to make a frame of wire, for a small round lamp you need to make three circles with a diameter: 12, 18, 26 cm. Then the circles are fastened together with a fishing line. The top will be the largest diameter, there should be the same distance between them.
In spoons, make a small hole with a thick needle at the top of the handle.
Spoons stain acrylic paints in three colors, for example yellow, orange, red.
Assembling a homemade chandelier: the line is cut to a length equal to the distance between the circles. A spoon is tied to one end of the fishing line, and the other to the frame. Spoons need to be tied to the lower circle of small diameter yellow color, to the middle - orange and to the top - red.

Light and graceful shade

For a paper shade, paper or thin cardboard is suitable. Such a shade can be either rectangular or square. First, you need to think about the size of the plafond, the larger the room, the wider the structure can be. In a small nursery or hallway, a shade with a diameter of 30 - 35 centimeters will look good.

The frame can be made of wire, it will consist of an upper and a lower part, consider making a shade in the shape of a cylinder.

You need to make two circles of wire of the required diameter. They are connected to each other using a fishing line, the distance between the lower and top frame- 12 - 15 cm, with a fishing line the hoops are fastened in three, four places. The larger the base diameter, the more connecting elements need to be made.
You can draw circles on a paper blank different diameters, figurines of cartoon characters. Outline drawings can be taken from the Internet and printed, then redrawn using a carbon copy. A special ruler is suitable for drawing circles, or you can outline caps or buttons of different diameters. Some drawings are cut completely with a clerical knife, some are cut along the contour.
The paper is tried on on the base and glued with an overlap. Then they are glued to the wire, it can also be fixed with thin wire... To do this, first, a hole is made in the paper with a thick needle or an awl, then a wire is threaded and carefully tied to the frame. It is advisable to glue thin paper, as it is easy to spoil it.

Exclusive shade made of metal cans

Basins of any metal are used, an interesting option will be obtained from copper or aluminum containers. An old used basin will do as well. If there is a through hole in it, it needs to be welded or sealed, for example, epoxy resin.
The inner surface must be painted in a light color so that the light is reflected from it as much as possible.
The outer surface can be painted dark, saturated color in harmony with the interior.
A fringe about 5 centimeters long is glued to the lower part of the rim with hot glue. In the central part of the basin, you need to make a hole for the wire. It can be drilled with a drill or pierced with a nail.

Such a shade can be decorated with CD mosaics. To do this, the discs are cut with sharp scissors into small fragments, which are glued to the outer surface of the pelvis. You can only glue the bottom outline, and paint the rest. Or decorate the entire surface of the plafond with such a mosaic. The more convex the surface, the finer the disc fragments should be.

Natural materials

An original lamp can be made from a dry branch of an unusual shape. It must be cleaned of bark and covered with a stain, then, if desired, treated with transparent varnish. The branch must be attached to a hook on the ceiling using a regular line. Then I wind the wire with the lamp around the branch several times. A branch entwined with several wires looks beautiful.

You can make a lamp out of plastic hangers. Described in detail in the video:

Luminaires for different rooms

DIY bottle chandeliers are more suitable for the kitchen. Constructions made of glass or plastic will be easy to clean from dust and, if necessary, wash. For the kitchen, hallway or living room, a lamp from natural wood.

For a children's room, a plafond made of painted plastic bottles, a floor lamp made of bright threads or paper composition... The last option cannot be called durable, but this is the option that children will like. Girls will love a shade with butterflies, floral elements, boys will love designs with cars, superheroes or bright plastic shades.

In some cafes and pubs they are used to decorate the hall. original lamps from bottles. These can be beer bottles. They can serve as both a shade for light bulbs and be an interesting frame for a lamp.

Homemade lighting ideas by location

With your own hands, you can give a new look to a floor lamp. You can decorate the plafond with cloth, threads, paper with cut-out patterns; you also do not need to ignore the base and leg of the lamp. They can be painted with acrylics, glazed, decorated with beads. The decor of the lower part of the floor lamp should overlap with the elements in the upper part. The easiest option is to decorate the plafond solid color lace or guipure.

Lighting fixtures

The lower part of the plafond made of threads can be decorated with pompons of the same size hanging on a thread. They are glued on the inside of the frame with glue. Pompons can be hung on the same or on different heights... They can be made in one color or several shades can be combined.

To decorate paper lamps, you can use lace, thick tulle, beads different sizes... You can decorate glass jars or bottles with glass pebbles, which can be purchased at hardware stores. You can also use buttons in different sizes and colors. Small buttons can be glued even on PVA.

On new year holidays it is customary to decorate a Christmas tree, but you can also decorate the shades of lamps, floor lamps. Here you can use ordinary rain, do-it-yourself snowflakes, Christmas tree figures, decorative balls and an ordinary garland. If an energy-saving lamp is installed in a wall or floor lamp, then its shade can be decorated with paper snowflakes.

Wall sconces installed in living rooms, bedrooms, children's rooms. After renovation, you can use old sconces only by changing them. appearance... You can paint the body of the lamp in a light color, and on top apply bronze or silver paint with a brush with a hard nap to create a patina effect. If the shade is made of glass, the pattern you like is applied to its surface using a glass stencil. Here you can use contour (they are used to create a stained glass window) or spray paints.

It takes ~ 3 minutes to read

Save

Each piece of interior that is made by hand is able to fill the house with special comfort and warmth. In addition, such crafts will not only look great in any room, they will become a completely exclusive item. Chandeliers made on their own using scrap materials will look very original in the house. This is a great idea!

To create such a wonderful piece, discover the inimitable design talent that is present in every person. It is this revealed quality that will bring into the house not only bright light, but also a cozy atmosphere.

Save

DIY kitchen chandelier

A similar handicraft product will look very elegant and graceful in the kitchen. And when guests come to the house, they will not even be able to guess that such a chandelier was made with their own hands, and not purchased in an expensive designer store. Imagine their admiration if they find out that it was you who were able to create such a masterpiece as a chandelier with your own hands. It is always fabulous in the kitchen with such a product.

Save

You will need the following materials:

A leg that can be removed from an old chandelier.
A hemisphere that is made of metal.
Any light fixture that has been used in the home in the past. You can disassemble and remove the required part. If this is not available, then an old school globe, previously cut in half, will do.
Sandpaper. It may not be useful, but it should still be available just in case you have to do some cleaning to get a perfect surface.
Wallpaper glue. Use this particular look as it dries and becomes completely transparent.
Regular sponge.
Dye. For the manufacture of a chandelier, you can take a matte finish, which is also used for painting walls.
White fabric.
Artificial leaves as well as flowers.
Half beads.
Beautiful ribbon.

Save

So everybody necessary materials are at hand, you can come directly to the manufacture of a beautiful chandelier for the kitchen.

First, dilute the glue and lower a piece of fabric into it. All material must be completely saturated with glue. Now you can lay out a sticky piece of fabric on the previously prepared hemisphere - this is the future shade. In order to make it more convenient to make folds on it, you can use any sharp object to make small cuts. Wrap everything that remains to stick out inside the product. The lamp must be completely pasted over.
Give the garment time to dry.
We take a sponge and paint the surface with it (inside and outside). Once the paint is completely dry, it is better to apply another coat for reliability. Now you can attach the resulting product to the leg.
The next step is to decorate the lamp. But first, think carefully. Decide what the final product should look like. You can make a few sketches on paper with different options design. When decided, then you can go to further work over the lamp. First, glue the decorative leaves in random order. Then comes a layer of flowers. If you have figurines ladybirds, for example, you can attach them too.
To complete the composition, you can decorate everything with a beautiful ribbon. But attach it in such a way that it is under the leaves, so it is more beautiful.
At the end, you can add half beads to the composition. The lamp is ready.

Save

Chandelier made from old plastic cups

Save

Many people are involved in creating amazing and beautiful things that are perfect for decorating the interior of the house. But often everyone forgets about chandeliers and lamps. Or maybe there is simply no idea for creativity ... That is why so often people ask the question: is it possible to make a chandelier with your own hands using what is at hand? Yes of course!

Necessary materials:

Plastic cups (about 300 pieces).
Staples and stapler.
Bolts.
Washers (one large and one small).
An energy-saving light bulb (this type is taken, since the usual one heats up very much).
Cartridge with wire.

Let's move on to making a chandelier:

Use a stapler to hold the three glasses together. It is best to start the connection from the bottom, and then move to the very top. What happened is the basic design. The resulting product is attached to the rest of the cups. The tapered design provides a sphere. And we must not forget that when everything is ready, you need to leave one hole for the cup empty. It is in this last glass that you burn a small hole. Place a large washer inside.
The electrical wire is tied in a knot and then pushed out through the holes.
Now attach the cup with bolts and small washers. If some kind of breakdown occurs, then all this can be easily disassembled. Using the same technology, you can also make a floor lamp by finding a suitable and beautiful stand.

Save

Openwork sconce or floor lamp

Chandeliers (lamps) and sconces, which are made of improvised materials with their own hands, always look very beautiful. Any glass jar can be used as a shade, and a container for bulk products is also suitable. For the elements of decorating the lampshade, crocheted lace will be used.

Save

For the manufacture of the lamp you will need the following materials:

Glass container and tin lid.
Hex nut.
Drill with drills.
Electric wire.
Bracket and chuck.
Electric lamp.
A napkin or any lace product.
Aerosol adhesive and paint.

You can get to work:

It is necessary to drill a hole in the very center for fastening. And also you need to make four holes in a circle to avoid overheating.
Now we attach the bracket, nut and cartridge, and then install the light bulb.
A layer of glue is applied to the surface of the can and then lace is applied. They can be applied to any part. It all depends on the imagination.
If you plan to make a sconce, then an openwork napkin can be attached with ordinary tape. Then everything is painted with spray paint. When the product is dry, the napkin can be removed and the painted shape will be preserved.

Save

Rose petal chandelier (DIY pendant lamp)

Save

This is a very romantic version of a pendant lamp.

Stock up following materials, before you start making:

Wooden embroidery hoop (you need 3 pieces of different sizes).
Rose petals (you can buy them at special store for decoration or make it yourself by cutting them out of thick white fabric).
Silk thread.
Paste starch.
White acrylic paint.
Fishing line.

Getting started:

Cut out white circles from the fabric, and then glue them with paste in pairs. Run a white thread between them. The length should be approximately 40 or 50 cm.
Now let's move on to coloring the hoop. You need to use white paint... Then we hang them on the fishing line in the following sequence: the most big ring, after - the average, and the last will be the smallest.
Now tie the petal threads to the hoop. In the place where the binding is made, glue a circle of fabric. This process is very time consuming. But the result will be excellent.

Save

Wire butterfly chandelier

This is a very original chandelier that will bring a constant feeling of summer and warmth to your home. Flocks of butterflies will literally come to life after a slight breeze blows. And the best part is that it is very easy to make such a chandelier with your own hands. The idea of using a beautiful butterfly to make this lamp is very good.

Necessary materials:

Lampshade that has two rings.
Decorative chains.
Scissors.
Silver paint (preferably aerosol).
Very thin marker.
Transparent plastic.
Pliers.
Silver wire.

Completing of the work:

The lampshade is painted with silver paint.
A stencil is made in the form beautiful butterflies... Here you can use your imagination and do everything yourself or find ready-made samples on the Internet.
We cut out butterflies from plastic according to stencils.
Several butterflies need to be painted silver. The rest should remain transparent.
You need to cut the chains 10 cm long. Now you need to put on transparent beads on them. So, the product can be given a very beautiful view because the beads will sparkle every time the sun hits them.
Next, you should attach the butterflies using pliers and wire. We attach the remaining end of the chain to the lampshade.

Save

Making from disposable spoons

Save

Such an uncomplicated object as a plastic spoon can become a real masterpiece in skillful hands... Let's consider how to make a chandelier from such material.

Necessary materials:

One 3 liter plastic bottle.
Glue.
Nippers.
Plastic spoons (one large package).

Chandelier assembly:

Using nippers, separate the heads of the spoons.
Next, cut out the bottom of the bottle.
Starting from the very bottom of the bottle, proceed to gluing the spoon heads over the entire surface of the bottle. Each new row must be glued so that it goes over the previous one. Stagger the spoons.
When we come to the neck of the bottle, you need to stop. At this point, a ring is made that resembles a bracelet. We make it from well-glued spoons.
For this chandelier it is necessary to use only energy-saving bulbs, as ordinary bulbs get too hot. And this will ruin the structure.

Save

Original idea: thread lampshade

Save

Threads are another very beautiful and simple improvised material that can be used to make a beautiful chandelier with your own hands. You will get a very unusual plafond. The following materials must be prepared:

Balloon.
Knitting.
Starch glue.
Lighting fixtures and wire.
Foam brush.
Yorshiki.
Scissors.

Lighting devices can not only dispel the darkness, but also give an unusual aura to your interior.

There are many different ideas with which you can make Wall Light or any other type of lamp with your own hands.

You yourself are able to create a masterpiece that cannot be found in any store.

Creating an extravagant chandelier

Very original thing is obtained from the simplest materials, most of which can be saved after a picnic. Lamps from various containers will look spectacular.

To do this, you will need:

oval plastic bottle with a capacity of 5 liters;
disposable spoons;
cable with socket and plug;
low power LED lamp;
pliers;
glue gun;
screwdriver;
stationery knife.

To avoid fire, use only LED bulb!

Using a knife, carefully cut the bottom of the bottle, then remove the handles from all plastic spoons. Apply a small amount of hot glue from a gun to the cut site, glue them from the bottom of the container.

You will need approximately seventeen pieces approximately. Place the next and other rows in a chessboard order.

In order to hide the neck of the bottle, put ten to twelve spoons without a handle on the glue so that they form a ring.

Pull the socket with the lamp and cable through the hole on the bottom of the bottle.

If there is no desire to make this part with your own hands, there is an opportunity to purchase it in any department of household goods - the wire, socket and plug are already connected together.

Make a hole in the lid for the cord by drilling it with a drill or a hot self-tapping screw. Screw on the lid, put on the previously prepared spoon ring on top. Exclusive LED lamp ready for use.

A few ideas for creating lampshades

It is enough just to create a lamp from scrap materials for your home or summer cottage.

Idea N1

any hollow dish (this can be an old saucepan or flowerpot);
wire;
polyurethane foam and gloves;
paint and brush;
sharp knife;
pliers.

Place the object taken as a base upside down. Wind the wire around the product the way you want the lampshade to be, since all the turns copy its shape. Put on gloves and squeeze the foam out a little on the frame so that it completely covers the wire, leave to dry.

Then, using a knife, give the contours more evenness and paint in any color. This option will be the best for a street lamp.

Idea N2 - a classic

thick wire;
pliers;
a small bottle of water.

Note!

To make the top center piece, wind a coil of wire onto the bottle, then remove it and cut off the excess. The ends must be fixed so that they form a ring, the diameter of which should allow the cartridge to be threaded at the bottom, and not to let it come out at the top.

Next, you need to make a large outer ring from the wire. You will need four equal pieces of wire to secure it. Connect one edge of each with a small ring, and the other with a large ring. The upper part of the lamp is ready.

The bottom circle of wire will be the largest, it must be attached to the second top one, evenly placing five identical pieces of wire.

To decorate the frame, pass the wire through the second upper ring, giving it a wavy shape, wind it onto the base. Design the bottom ring in the same way.

Note!

Take with you for a walk in the woods interesting shape a branch, it will make an excellent lamp made of wood. Wash the branch and peel off the bark with a knife, cover with wood varnish. For good stability, screw the lamp to a heavy stand with self-tapping screws, it can also serve as a tree.

A better option is an oak tree, find a broken branch and saw off a circle at least five centimeters thick from it. Cover it with varnish or paint it too.

Making a lampshade with children

There is an option for making a lampshade with children. For the frame, you will need a canister or bottle with a capacity of five liters. You need to roll the paper strips into a tube, it is best to wind them around a pencil or sushi stick, then glue the remaining edge with glue.

These blanks must be glued to the frame in several layers so that there are no gaps. Once the glue is dry, you can put the lampshade over a table lamp or make a ceiling lamp that looks very unusual.

Experienced needlewomen can knit or crochet a lampshade, decorating it with knitted flowers, ribbons.

To give the product the correct shape, you can use a starch solution or ordinary PVA glue. Look at the proposed photos of knitted lamps, how much tenderness and comfort they have!

Note!

This article told you how to make a DIY lamp. Using the information received and your own imagination, now you can create an exclusive lighting fixture for any room.

DIY lamp photo

Lighting is the most important component of the interior. The coziness and level of comfort of our home depends on the lighting. The play of light and shadow allows you to play up the winning moments of the interior and divert attention from unfortunate moments. And also - lamps, floor lamps, chandeliers and lamps create the atmosphere that we call "home". Unique lamps and The best way- make a lampshade with your own hands. Homemade shades and lampshades are the strong point that will make your home stand out from others.

A few words about safety

In the manufacture of lamps, floor lamps and chandeliers in industrial conditions, a preliminary calculation is made of the minimum distance from the "body" of the lamp to the materials. This distance depends on the power and thermal radiation of the lamp and on the type (combustibility) of the material from which the shade / lampshade is made. At home, hardly anyone will bother with such calculations. And in order not to create dangerous situation, it is worth adhering to certain rules.

And in general, having made a lampshade and installing it, in the first few days, pay attention to whether the lamp shade is warming up. Any rise in temperature above the environment... If the shade feels "warm", change the bulb to a less powerful one. Check again. So until the homemade lampshade is warm.

Where to get the frame

If you want to remake an old lamp, a floor lamp, the sconces of which the old lampshade has become unusable, you can simply use the existing base by stripping old stuff... Before starting work, inspect the frame well, if there is rust or damaged coating somewhere, maybe it is worth peeling and painting everything again? At the same time, the color can be changed. If you don't have the old frames, you can buy an inexpensive lamp (at a store or at a flea market) and do the same thing with it. Quite good lampshades can, by the way, be made from waste baskets. They are wire, there are plastic. The main thing is to find the right one in shape and size. Then in the bottom you make a hole for the cartridge. Further - it's up to the decoration / cladding, and then there are a lot of options.

If this method is not available, you can make a lampshade without a frame (there are some) or make a frame yourself. The material for making a frame for a lampshade with your own hands is: wire, wood (wooden or bamboo sticks, specially cut elements), plastic bottles.

How to make a wire frame for a homemade lampshade

The wire for the lamp frame needs aluminum or steel. It is easy to work with aluminum, but it wrinkles easily. This is not very important when the lampshade is already in use, but this fact must be taken into account during operation: you can ruin the shape. On the other hand, such plasticity makes it easy and simple to make changes to the shape during operation. So it's not a bad option. Aluminum wire can be obtained from electrical cables. You will have to remove the protective shell and you can use it.

Steel wire is more elastic so that it retains its shape well. You can search for it on construction market... Working with her is more difficult. It is desirable to have strong male hands nearby.

In addition to the wire, you will need powerful wire cutters and pliers for work. The frame of a lampshade usually consists of two rings and posts connecting them. The shape of the future lampshade depends on the size of the rings and the shape of the racks. Questions may arise about the number of racks and how they are attached. The number of posts depends on the size of the rings and how “round” you want the lampshade. The more racks there are, the smoother the fabric will be. So it's up to you, but the optimal distance between the posts along the lower circle is about 5-6 cm.

Techniques for creating a frame for a wire lampshade

How you attach the stack to the rings of your lampshade depends on the thickness and type of wire and the tools you have. The easiest way is to make a small hook at the end, then clamp it tightly. And so that the ring does not slide left and right, pre-process the wire at the attachment point sandpaper with coarse grains. This is an option for thick aluminum wires. If the wire is steel, with a diameter of 1.2-2 mm or more, the best way is. The thinner wire can be bent and wrapped around the ring, or you can also make a hook.

If you make hooks, wrap the wire, the appearance is far from being as ideal as that of factory frames. But this imperfection will be covered by the lampshade itself. If you still care about it, find a ribbon of a suitable color (usually matched to the color of the lampshade) and carefully wrap the resulting frame. It will get much better. The tape can be coated with PVA glue and, wet, tightly, turn by turn, wrap the frame.

Wire mesh

If you can find a thin wire mesh, you can quickly make an almost perfect cylindrical shade for a floor lamp, table lamp, night light, candle shade, etc. All you need is to cut off a piece of mesh of the required length and width, roll it into a ring and fasten the wires by wrapping them around the racks.

To prevent the mesh from straightening when cutting a piece, cut so that there are long loose ends on both sides. They will be used to fasten the cylindrical shade. And the imperfection of the upper and lower rings can be masked with a tape of the desired color.

From a five liter plastic bottle

An interesting shape of a lampshade can be obtained from a large-capacity plastic bottle. There are bottles of 5-6 liters and even 10. So they can be used. Cut off the top or bottom from the container - depending on what you like best. In the cut off part, we make a ring for the cartridge. If the top is cut off, the neck can be used for some cartridges. For those with a larger diameter, it will have to be cut off.

Then we cut out the excess plastic, form the rims and stands of the plafond. In order not to be mistaken, you can first draw all the lines with a marker. It will be easier to cut. Everything is elementary. Then we just decorate. And yes, you must cut out the plastic, otherwise warm air nowhere to go.

We make lampshades on the frame

There are enough options for how you can make a lampshade cover:

From ribbons

The easiest and quickest way to convert an old lamp shade to a floor lamp or table lamp is to use ribbons. You need a frame or a lampshade in the form of a cylinder. It can be “naked” or covered in fabric. If you use a bare wire frame, light will filter through the slits, which will create interesting lighting effects, but the lighting will be uneven. It is inconvenient to read in this light - this is an interior solution. If you need even lighting, wrap the fabric over the frame first. It can be the same color as the ribbons, a couple of tones darker or lighter, it can be contrasting. It all depends on your desire. And remember that the darker the fabric, the less light the lampshade lets through.

We take a tape 1-2.5 cm wide. We fix it from the seamy side of the lampshade using PVA glue, additionally fixing it with a pin. If we took a wire frame without fabric, we attach it to the upper or lower rim (you can sew it with your hands, you can use glue). Then we begin to wrap the entire frame, from top to bottom, placing the turns of the tape close to each other, but without overlap.

Having completed the circle, unfold the tape 90 °. We fix it in this position (with a needle and thread or PVA glue, glue from a pistol, temporarily fixing it with a pin, pressing it with a clothespin). Then we pass the tape under the first tape, take it out, put it on top of the second one, then pull it down again, pull it up through one tape. So, gradually, we create a weave, filling the entire lampshade.

Alternatively, you can skip two vertical belts. But then you need to make sure that each next row is shifted by one crossbar. Then you get a different type of weave. Such a lampshade is ideal for floor lamps, as it will direct the light downward, and the dispersion through the walls will be small.

In this version, the ribbons can be the same, they can be of the same color, but of different textures, they can differ by a couple of tones or be contrasting. The tapes can be run in a continuous circle around the circle, or after a certain distance. If you find a wide tape and overlap it, then you won't need horizontal ones at all. And if you use a braided or twisted cord (in the lower photo on the right), we get a completely different lampshade. So only this technique of finishing the lampshade gives a lot of options.

Let's briefly present the ideas. There are many options for how you can customize standard lampshade frames. The first method has already been announced: you can knit a lamp shade cover on knitting needles or crochet. Several options in the photo.

Not everyone knows how to knit. It's easier to work with beads, especially if you glue them. You can decorate old fabric with beads, sequins, beads different shapes and sizes. You can make such a "new-old" lampshade with your own hands in a couple of hours. Pick up jewelry that matches the color, coat the fabric with PVA glue, glue the jewelry. To complete the image, you can assemble pendants from beads and beads that are attached to the lower rim, but this is already painstaking work... The effect is interesting though.

You can sew a new fabric lampshade. But it is not necessary to make it an updated copy of the old one. Fantasy should be included! If a lamp or floor lamp is in the girls' room, new case on the lampshade can be made in the form of a skirt. You choose the style of the skirt yourself. They look interesting in the fold. With and without ruffles.

In the boy's room, you can use the old geographic map... They are on thick paper... If the paper is not thick enough, you first need to glue the card onto the cardboard, and then glue the lampshade from such a blank.

Original shades are obtained if the finished frame is braided with threads or ropes. The ropes can be natural. In this case, they are gray, brown beige. Thin synthetic colored cords can be found. From them you will get more "fun" in color products. The situation is even simpler with knitting threads. They are thin, thick, textured, with a smoothly changing color. In general, there are a lot of options.

We take the frame and weave it according to a certain pattern. You can start with the racks. Braid each rack with a pigtail (the length of the threads should be 3 times the height of the rack). When this work is over, we begin to stretch the threads / ropes between the posts. They will need to be passed through the pigtails, so with threads it is more convenient to do this with a needle, and the ropes can be inserted like that.

The second option is to first entangle the entire frame horizontally, and then braid the racks. The pigtail will not work here, you just need to fix the turns on the rack with inclined stitches with a certain inclination. This version is somewhat simpler in execution, but the "pigtails" look more decorative.

Homemade shades without a frame

Many materials are tough enough to hold their shape on their own and, at the same time, they are flexible enough to make something interesting out of them. Of such homemade lampshades well, a lot. And almost all of them are worth your attention. We will give here only a part, the other part will go in the section with photos (see below).

From knitted lace napkins

Many people have crocheted napkins and they lie in the "stash boxes", as it is a pity to throw it away, and do not know how to use it. There are very interesting idea- to make a lampshade out of them for a chandelier on a suspension. In addition to napkins, you will need a large balloon or bouncy ball, glue for heavy wallpaper(vinyl, silkscreen, etc.), brush.

Soak the glue according to the instructions, wait until it swells. We inflate the ball or take the ball, hang it up. When the glue is ready, lay out a napkin on some clean surface, coat it with glue, put it on a ball.

It is necessary to spread it on such a condition that a hole for the cartridge remains in the center. Glue the napkins one by one. They should be laid out so that the edges overlap a little. When all the napkins are laid, we coat them with glue again and leave to dry. When the glue is dry, blow off the ball or ball (the ball can be punctured, if not sorry) and take it out through the hole. That's all, lace lampshade ready.

In some cases, problems arise with how to hang the finished lampshade on the cartridge. The problem is solved simply - take a transparent plastic bottle, cut off the neck of it, if necessary, expand the hole to the required size (so that it fits tightly on the cartridge), then cut off the plastic so that you get a ring 5-7 cm wide.You coat this ring with PVA glue, and glue it to the lampshade from the inside of the ball.

Round shades made of threads

Practically the same technology can be used to make round and semicircular stylish shades. Choose a thread of a suitable color. Their composition is absolutely unimportant - the color, thickness and texture are important. They can be shaggy, smooth, twisted, thinner and thicker. The appearance depends on it. It is most convenient to work with medium-thick cotton threads. They absorb glue well and then, after drying, keep their shape perfectly.

You will also need a ball or a ball. This will be the base of the lampshade that defines the shape. The dimensions of the base are selected at will. The threads will need to be glued, for this you need PVA glue. It is poured into a container, diluted with water in a 1: 1 ratio.

Other glue can also be used. It is important that it becomes transparent after drying. These are WB-29 from TYTAN Professional and D2 glue for carpentry work. If you will be using any of these types of adhesives, read the instructions.

Draw a circle on the ball or ball, which will be slightly smaller in size than the lamp holder. Draw a larger circle on the opposite side - this will be the lower edge of the plafond. Now everything is ready, we can proceed.

We coat the threads with glue and wind them around the ball in a chaotic manner. It is more convenient to do this if the glue is poured into the container - you can lower the entire skein there, and just slowly pull the thread. With glue in a tube, everything is not so comfortable: you have to coat areas up to a meter long, wind it up, smear it again. Time takes much longer. This is if you use non-PVA. But on the other hand, the products turn out to be more rigid and do not sag, do not change shape over time, as can happen with filament lampshades on PVA.

When winding threads on a ball, we carefully go around the drawn circles. If you accidentally climbed into the "forbidden territory", we simply move the threads, forming an even (more or less even) edge. When the threads run out or you decide that there is enough density, the process can be stopped. We thread the edge of the thread between others. Everything. Then we coat the ball with wound threads again with glue (PVA can be poured) and leave to dry (at least 2 days). To prevent the ball from rolling, we find a bowl or saucepan and use it as a stand.

The last step is to blow off the ball or ball. If the ball has a nipple, press on it with a thin wire, releasing air. We take out the deflated ball. That's all, you can thread the lamp inside and test the lampshade.

The technology is the same, but the look is very different ...

Using the technology described above, it is possible to make not only round shades. Rectangular, triangular, trapezoidal. Choose a base that is easy to remove, wind the threads dipped in glue, braid, even sticks, newspaper tubes, etc. After drying, remove the base and now, you have made a lampshade with your own hands. A couple of examples in the photo below.

You can also use sticks…. Only wrap the ball with cling film and use transparent carpentry instead of PVA glue.

It is pasty polymer clay in a tube, which was applied to a milk bag, then dried and the bag was removed ...

Creative homemade shades for lamps, floor lamps and chandeliers

You just wonder why people don't make beautiful and unusual things. Plafond from a cup, grater, bottle, beer or glass jars, metal parts and rings from beer cans ... It seems that everything can be used ...

Old sieve shade ... stylish

Candlesticks turn into lamps ... without lampshades

You won't tell in real life, but these lampshades are made of hooks used to open metal cans for drinks and canned food ... if you paint them, it will be even more interesting

Not sure what to do with granny's crystal? Make plafonds out of it ...

Many designers recommend using multiple light sources in a room, ranging from chandeliers to lamps and floor lamps. This will allow you to illuminate specific areas in the room or create a special spectrum of lighting depending on your mood. But in order to realize the plan, significant financial investments will be needed, since creative and cost a lot of money. In this regard, you can make yourself floor lamp and at the same time do not spend much money. You can assemble it from scrap materials, such a product will look good in country house, apartment or in the country. Next, we will tell you how to make a floor lamp with your own hands, providing instructions with photo and video examples.

Step-by-step instruction

Preparation of materials

In order to make a homemade lamp, you will need the following tools and materials:

lumber and wood glue;
hacksaw;
drill and pliers;
knife, screwdriver;
fasteners;
copper elbow;
wooden beam for the frame (approximately 140 cm);
copper tube for the frame (about one meter);
lamp and electric cord with a plug;
plastic garbage bin (openwork).

You should make a floor lamp yourself step by step. First of all, you need to start making the base of the structure.

Making the foundation

So, the foundation is done as follows:

First of all, two planks should be cut from the board. One should be 35x5x20 cm in parameters (length, thickness, width, respectively), the other - 30x2.5x15 cm. Other dimensions can be taken, but it must be borne in mind that the base must withstand the weight of the entire structure and not allow it to tip over.
Then you need to glue the two bars with glue. To do this, grease the smaller board with special glue and attach it to the larger board. This must be done so that it is in the center. Using clamps, fix the bars until the glue is completely dry.
After that, you need to measure 5 centimeters from the edge and make a hole with a diameter of 3 cm. And since the base is relatively thick, you will periodically need to remove the wooden parts from the hole. Once the hole is through, sand all edges.

We make the frame

For the frame, a stand of almost one and a half meters was chosen. This height was selected taking into account that a homemade floor lamp can be placed near the sofa and the light will fall on it from above. But you can choose a different height.

Before proceeding with the manufacture of the frame, you need to wipe copper pipe alcohol. This will remove any remaining stickers and grease.

Then you need to do the following:

We collect the lamp

To assemble a homemade floor lamp you need:

Coming up with a lampshade

It is very easy and simple to make a lampshade. To do this, it is enough to have an ordinary office wastebasket with you and adhere to the following instructions:

The floor lamp is made by hand. Now you can put it near your favorite chair, open a book and enjoy reading. Photo finished product pictured below:

A floor lamp for a home can be assembled from a variety of materials at hand. For example, one can simply change old lamp by adding a new leg or lampshade. For lovers of coziness and comfort a great solution there will be a lampshade made of threads and beads. To do this, you need a mesh and thread. Satin threads are wound around the mesh, and the lampshade is installed on the rack.

Also, the lampshade can be constructed from plain white paper or fabric. Homemade frame wrapped with cloth or paper and with the help of special paints give it their own style. And handmade jewelry made of beads, shells, rhinestones or buttons will give the lamps their individuality and originality.

We recommend watching a video showing master classes on assembling a floor lamp from scrap materials. Find out how to do beautiful lamp floor type out of the drum washing machine, and tabletop model from paper plates:

Such unusual ideas will allow you to create a lamp for any room interior. The advantage of a homemade floor lamp is that no one will have such a product. It will be special and individual. Moreover, you can make not only floor lamps, but also build a table lighting device that can be placed near the bed.

So we looked at how to make a do-it-yourself floor lamp at home. We hope that you liked the provided photo and video examples, as well as master classes and inspired you to make homemade lamp from scrap materials!