How to make a floor lamp from a table lamp. Floor lamp

Many designers recommend using multiple light sources in a room, ranging from chandeliers to lamps and floor lamps. This will allow you to illuminate specific areas in the room or create a special spectrum of lighting depending on your mood. But in order to realize the plan, significant financial investments will be needed, since creative and cost a lot of money. In this regard, you can make a floor lamp yourself and at the same time not spend much money. You can assemble it from scrap materials, such a product will look good in a country house, apartment or in the country. Next, we will tell you how to make a floor lamp with your own hands, providing instructions with photo and video examples.

Step-by-step instruction

Preparation of materials

In order to make a homemade lamp, you will need the following tools and materials:

lumber and wood glue;
hacksaw;
drill and pliers;
knife, screwdriver;
fasteners;
copper elbow;
wooden beam for the frame (approximately 140 cm);
copper tube for the frame (about one meter);
lamp and electric cord with a plug;
plastic garbage bin (openwork).

You should make a floor lamp yourself step by step. First of all, you need to start making the base of the structure.

Making the foundation

So, the foundation is done as follows:

First of all, two planks should be cut from the board. One should be 35x5x20 cm in parameters (length, thickness, width, respectively), the other - 30x2.5x15 cm.Other sizes can be taken, but it must be borne in mind that the base must withstand the weight of the entire structure and not allow it to tip over.
Then you need to glue the two bars with glue. To do this, grease the smaller board with special glue and attach it to the larger board. This must be done so that it is in the center. Using clamps, fix the bars until the glue is completely dry.
After that, you need to measure 5 centimeters from the edge and make a hole with a diameter of 3 cm. And since the base is relatively thick, you will periodically need to remove the wooden parts from the hole. Once the hole is through, sand all edges.

We make the frame

For the frame, a stand of almost one and a half meters was chosen. This height was selected taking into account that a homemade floor lamp can be placed near the sofa and the light will fall on it from above. But you can choose a different height.

Before you start making the frame, you need to wipe the copper pipe with alcohol. This will remove any remaining stickers and grease.

Then you need to do the following:

We collect the lamp

To assemble a homemade floor lamp you need:

Coming up with a lampshade

It is very easy and simple to make a lampshade. To do this, it is enough to have an ordinary office wastebasket with you and adhere to the following instructions:

The floor lamp is made by hand. Now you can put it near your favorite chair, open a book and enjoy reading. A photo of the finished product is shown below:

A floor lamp for the home can be assembled from a variety of materials at hand. For example, you can simply modify an old lamp by adding a new leg or lampshade. For lovers of coziness and comfort, an excellent solution would be a lampshade made of threads and beads. To do this, you need a mesh and thread. Satin threads are wound around the mesh, and the lampshade is installed on the rack.

Also, a lampshade can be constructed from plain white paper or fabric. A homemade frame is wrapped in cloth or paper and, with the help of special paints, gives it its own style. And handmade jewelry made of beads, shells, rhinestones or buttons will give the lamps their individuality and originality.

We recommend watching a video showing master classes on assembling a floor lamp from scrap materials. Learn how to make a beautiful floor lamp from a washing machine drum, as well as a tabletop model from paper plates:

Such unusual ideas will allow you to create a lamp for any room interior. The advantage of a homemade floor lamp is that no one will have such a product. It will be special and individual. Moreover, you can make not only floor lamps, but also build a table lighting device that can be placed near the bed.

So we looked at how to make a do-it-yourself floor lamp at home. We hope you liked the provided photo and video examples, as well as master classes and inspired you to make a homemade lamp from scrap materials!

When approaching the issue of planning lighting in an apartment, it is worth remembering that most designers recommend providing multiple sources of lighting in a room. One - central and several additional. Such a distribution of light has the most beneficial effect on vision and the psychoemotional state of a person.

Spotlights;
Wall lights;
floor lamp, or floor lamp.

Floor lamps - floor or tabletop - are often chosen for zoning in living rooms and bedrooms. Separating a cozy reading space is easy by choosing a lamp that matches the overall style of the room. It creates a soft atmosphere and diffused light ideal for reading.

But when you go to the store, it turns out to be very difficult to make a choice. A huge number of a wide variety of lamps of all types and shapes can be confusing. There is a simple solution - to make a floor lamp, ideal for your apartment, with your own hands. At first glance, it looks very complicated, but on closer inspection, nothing is impossible!

Lamp repair and restoration

If there is an old lamp in stock that has not been working for a long time, then the task is greatly simplified. You just need to adjust the length of the rack, if necessary - cut, refine the base - paint or decorate with a ribbon. An obligatory step is the replacement of the electrics - the cable, plug, switch and, if necessary, the cartridge are changed.

And the most pleasant thing remains - to make a lampshade for a floor lamp or to put in order a shade, which is also much easier - after all, the mount and frame are already there, it remains only to give freedom of imagination. At the exit, you get a fashionable, exclusive floor lamp from an old, non-working lamp, which was gathering dust in the pantry.

Necessary materials

To make a floor lamp with your own hands, you can use a variety of parts and materials that are in your home. You can give new life to things that no one has used for a long time.

When starting to create your own unique lamp, you need to prepare materials. The main details that you cannot do without:

the leg of the floor lamp is any hollow pin - metal or plastic. It is best to avoid wooden parts in contact with the cable;

electrical cable of the required length;
the cartridge is from an old electrical appliance. Usually use E27, which is suitable for a light bulb with a standard base;
light bulb - energy saving or LED. A conventional incandescent lamp gets very hot during operation, which can lead to a fire hazard.

Important! For a metal leg, a three-core cable is best.

Additionally, materials may be required to create a lampshade. They depend on what kind of plan it will be - paper, textile or glass.

What could be the basis

The basis for a future floor lamp can be very different, but its stability remains a prerequisite. The luminaire must stand firmly on the surface, so choose a heavy base. This could be:

wooden base... A large wooden circle - a cut of a log, a block, or several fastened together in a different way. Alternatively, you can make the shape you need out of wood with your own hands. The finished product must be sanded with sandpaper, and then either painted with a stain to show the texture of the tree, or painted in the desired color;
gypsum base... To create it, you need to dilute the gypsum with water and pour it into the mold, fixing the leg of the future floor lamp in it, for which you need to wait until the gypsum begins to set, but does not completely freeze. A split baking dish is ideal for this. The hole in the tube must be closed. The hardened part must be painted in the desired color or pasted over with paper of the required style.

Important! For greater strength, PVA glue and more water can be added to the gypsum, so cracks will not appear on the product.

For the base, any solid material available, of a suitable shape and with the necessary holes can be selected.

Floor standing or tabletop?

By and large, the only significant difference between a floor or table lamp is the length of the leg. For a floor-standing one, as a rule, it is a hollow pin where the wire is laid, and for a desktop one, options are possible.

You can take a ready-made leg from an old lamp that has fallen into disrepair, or you can make your own unique stand for the plafond. For example, you can take a plastic vase and make a hole for the cable at the bottom, and a holder for the cartridge on top. A floor lamp usually has one leg, but you can make a unique model with several supports, and then it will become a real decoration of the interior, attracting the eye with its uniqueness.

Lampshade - room for imagination

The lampshade is the brightest and most memorable element of the future lamp. It depends on him what kind of light will come from the floor lamp, and how it will fit into the situation. Creating a lampshade for a future floor lamp is a huge scope for imagination. The only limitation may be the style of your interior.

You will need a base for your lampshade - either ready-made - from an old lamp, or made with your own hands from strong wire that will hold its shape and side elements. The side elements must be attached to the base, trying to make the joints as invisible as possible.

If this could not be avoided - do not be upset - this can be easily corrected with the help of decor. The side elements can be: paper - plain, thin rice, corrugated, even the remnants of wallpaper; almost any textile with high light transmission; wooden slats - perfect for a rustic style; glass pendants or threads with strung beads - will give a mysterious shimmer.

The outer surface of the lampshade can be additionally decorated with rhinestones, ribbons, beads, felt elements, wooden details, textile flowers, as well as hand-painted - you just need to avoid heavy, heavy elements that will obscure the light. You can make a lampshade for a floor lamp with your own hands from almost any material, even from those that, it would seem, are not intended for this.

Installation of the finished product

When all the details of the lamp are ready, we proceed to the assembly. It is important to observe safety precautions when working with electrical appliances. We pass the cable through the base and the hollow leg, on the bottom of the base it is better to make legs for convenience, and fix the cable parallel to the floor so that it does not interfere with the stability of the structure. We attach a lamp holder to it and attach the lampshade. We connect the cable to the plug, and everything is ready - you can enjoy your work.

Important! All electrical cable fixing points must be carefully insulated to avoid short circuits.

Table or floor lamps fill the atmosphere with warmth and comfort, create a unique atmosphere. A hand-made element of your interior is not just a lamp - it is a unique exhibit that brings zest and personality to your apartment.

Floor lamps - one of the varieties of an additional light source, have a functional and decorative value. Colored and perforated lampshades not only create a special atmosphere, emphasizing the style of the interior, but also become an alternative to more powerful lighting fixtures, allowing you to use directional light and save energy.

Lightness and mobility, as well as the ability to change the appearance are two more advantages of floor lamps, in contrast to wall and ceiling lamps.

Layout and assembly of a floor lamp at home will not only save money, but also create a high-quality and unique product for yourself or as an original gift for loved ones.

Base for floor lamp

Before starting creative work on a lampshade and other decor, it is worth learning how to make a floor pole for a floor lamp with your own hands. To do this, you need to design the dimensions of the product, and purchase blanks of the appropriate dimensions.

For work, you will need two planks and a wooden beam, a narrow copper pipe, an electric wire with a plug, a socket and a lamp.

A step-by-step guide on how to make an angled pole lamp offers the simplest, but reliable and safe solution. It is convenient to place such a tilted lamp next to upholstered furniture or by the bed.

The foundation

Two boards are taken for gluing a stepped block: the thickness of the lower part should be twice as large as the upper one, they can be cut from standard boards of 50 and 25 mm. An example of the proportions of the width and length of rectangular base blanks with a rack height of 1.5 m: the lower part is 35x20 cm, the upper one is 30x15 cm.

The surface of the smaller part must be covered with wood glue and fixed exactly in the center, right next to the edge along the width of the large part.

Rack

We make parts for the rack. With an indentation of 5 cm from the two-layer edge of the base, using a drill with a nozzle, you need to make a hole in the diameter of 3 mm of the bar.

Next, with a small indent (depending on the height of the floor lamp), we drill a through hole for a copper pipe with an inclination of 60 degrees. Having stepped back 25 cm from the end of the copper workpiece, close to the joint, you will need to drill a hole for the electrical wire.

Assembly

First, you should try on the parts without gluing, to make sure that the holes are made correctly and the structure is stable. Then we fix the timber on the base with wood glue and let the workpiece dry. We pass the wire into the pipe and fix it on the riser. It remains to fix the elbow and the cartridge at the end of the pipe - and the frame of the floor lamp is ready.

For the floor stand of a floor lamp, you can use other materials, but before you do the installation of the structure with your own hands, you need to carefully calculate the dimensions and at all stages check the stability of the stand and the reliability of the fasteners.

In the case of recycling materials (such as plumbing pipes, machine parts, furniture, etc.), care should be taken to clean and sand the surfaces.

Lampshade and decor

To decorate a floor lamp, you can use both ready-made lampshades and lighting fixture parts, or make them yourself, using all the variety of materials and handmade techniques.

Bases and posts can be made of plaster, furniture boards and slats, threaded pipes and fittings, tripods, hangers, etc. Hollow supports will allow you to completely mask the wires, in other cases this can be done, for example, with decorative wrapping from ropes or straw.

The use of plastic springs will allow you to adjust the height of the floor lamp. The product can be equipped with switches and even a remote control.

Energy-saving LED lamps, due to their lower heating compared to spiral ones and a variety of color shades, are ideal for floor lamps. They are safe and give you more room to experiment with lampshades made from unconventional materials - paper, wood, plastic.

When choosing an original lampshade for a DIY floor lamp, you need to adhere to the general idea and take into account the style of the interior. The product should look good even when turned off, so it is important to carefully finish all surfaces, paying attention to the details.

Any of the modern styles of interior decoration can offer its own vision of this lighting device, and you can see this by looking at the collections of photos of floor lamps from various design schools. But at the same time, the scope of use of floor lamps has not changed over the past century.

Especially floor-standing models should serve as additional lighting in living rooms, bedrooms and offices. That is, they should fit in proportionally and stylishly into the interior, becoming not only a decor, but also a functional part of the furnishings.

A purely decorative role for floor lamps is not suitable, without use they turn into an unnecessary thing, causing irritation. This factor must be taken into account, both when designing the dimensions and when choosing a lampshade.

Fabric lampshades usually have a wire frame. The fabric is stretched from the inside, the outside is wrapped on the wire with braid. The lampshade can also be made from any suitable container - for example, a bucket, using perforations.

In some cases, it is better to put emphasis on the design and convenience of the counter, adding decors that have minimal impact on the light flow. These can be glass, plastic, ceramic or metal shades open at the bottom, as well as wire and lattice decors.

Photo of floor lamps with your own hands

Making exclusive interior items with your own hands is an exciting and very effective activity. You get two benefits at the same time: a stylish item that no one else has, and significant financial savings, because handmade items are expensive.

Today in stores you can find any kind of lighting device: any style, from various materials and for any financial opportunity. But the lamp, created in a single copy, is able to radically transform the interior, making it unique. An exclusive piece of furniture is not available to everyone - designer lamps are expensive. The way out of the situation when you want to and the price bites is to make a stylish device for lighting with your own hands. Today we will choose from all the variety of lamp options and try to make it right with our own hands, guided by the video instruction.

A little about the floor lamp

The word "floor lamp" is of French origin, it comes from "torche" and is translated as torch. This type of luminaire belongs to floor lighting fixtures. It is a high stand fixed on the base. The base is made heavy so that the structure is stable. The stand holds a lamp holder (or several). In the rack, electrical wiring runs, the switch is placed on the rack itself, on the base, or a switch on the bulb holder is used.

Depending on the design, the floor lamp can be used with or without a lampshade. In addition to the shape of the lampshade, both the stand and the stand can have different designs.

Three iconic floor lamps

Floor lamps have always attracted designers. Perhaps with its fragile, but at the same time, stable design and a kind of combination of uselessness and utilitarianism. On the one hand, this lighting fixture is very convenient - for example, for creating a cozy light above the armchair. On the other hand, it is its main purpose in the interior: creating a stylish environment.

The design world knows of several truly iconic lighting items, and three of them stand out for high design:

This incredibly stylish floor lamp was designed by brothers Achille and Pierre Giacomo Castiglioni in 1962 for Flos. The elegant lines of the floor lamp are probably known to everyone. The long, curved stand has a telescopic device that allows you to adjust the position of the lamp. You can additionally adjust the light "for yourself" by changing the position of the plafond.

The ideal arc of the pillar ends with a Carrara marble parallelepiped. A hole has been made in the marble block, which is not symmetrical about the base, but its position is precisely adjusted. It is designed to carry the lamp with a stick threaded through the hole.

The prototype of the Anglepoise family of lamps, including the floor lamp, was created in 1932. The author of the legendary lighting fixture is a person who is far from design and architecture. George Carwardine was a car suspension engineer. He applied his knowledge to create a comfortable working lamp that can be fixed in different positions with the help of springs.

The iconic lamp became the hero of the composition of the British rock musicians Soft Boys. In 1978 they recorded the song "I Want To Be An Anglepoise Lamp".

This sensual specimen (“Tetine” in French - chest) of lighting equipment is intriguing and mesmerizing. The shape of the plafond looks like a woman's breast, hence the name. And the black color and thin curved legs give the lamp the appearance of an insect. Tetine lamps were invented by the French sculptor Serge Mui in the 50s of the last century.

Do-it-yourself floor lamp in steampunk style

To make a stylish piece of furniture suitable for, you need a little:

wire of the required length - ballscrew 2 x 0.75 is suitable;
plug and switch;
lampholder with E24 base and clamping ring for mounting the shade;
plumbing products made of ferrous metal: bends, bends, couplings, tees - their number and dimensions depend on the intended design of the luminaire;
a flower pot as a shade;
metallic paint.

Attention! The material of the shade must be made of non-combustible material, otherwise your lamp may become a source of fire.

The principle of manufacturing a floor lamp in the style of steampunk from plumbing parts is that the fittings are threaded parts and are easily connected to each other in any configurations, like elements of a constructor. Think over the design of the future floor lamp and the required number of fittings, and then the assembly process takes place simply by screwing the parts onto the threads. Pull the cable through the pipe during assembly.

After the lamp body is ready, attach the socket, switch and plug. It remains to install the shade - you can use a plastic flower pot or any other item that suits your idea. After assembly, the floor lamp should be painted.

Advice. It is easier to use paint in an aerosol can: it lies smoother and easily paints over all the embossed parts.

Your DIY floor lamp is ready. This brutal model is suitable for a masculine interior. Although the industrial style of the lamp will fit perfectly into any modern interior.

DIY floor lamp: video

Original do-it-yourself floor lamp: photo

Each person seeks to use the opportunities available to him to create a more comfortable and cozy environment in his home, dividing rooms into different functional areas (rest, work, reading, cooking or eating).

There are a huge number of original design solutions. Lighting systems have long performed not only the main function, but also allow you to decorate residential and administrative premises. It is enough to make a floor lamp with your own hands, and the room will change significantly, sparkle with new colors.

A floor lamp is a common lighting fixture that was especially popular in the last century. Today a second life has been “breathed” into the device. Our material describes the independent manufacture of a floor lamp using improvised means.

The purpose of the floor lamp

With the help of one floor lamp, it is unlikely that it will be possible to organize the main lighting in the room. On the other hand, the appearance of this luminaire can significantly change the overall picture. A floor lamp is used to create a cozy atmosphere in a seating area or to provide directional light for working and reading.

Floor lamps will be indispensable in several cases:

organization of local lighting, as described above (highlighting the area where the chair, couch, sofa or other piece of furniture used for relaxation, reading, watching TV are located);
creating a romantic atmosphere for a late dinner with a soul mate;
a combination of different styles - a combination of eastern and western interiors;
search for an original solution that allows you to diversify the design of the room.

In addition, this device can be easily rearranged from one place to another, allowing you to update the interior at any time in your living space.

DIY floor lamp: step-by-step instructions

The manufacturing process of a floor lamp consists of several main stages.

Preparation of the necessary materials and tools

Before starting work on the manufacture of a floor lamp, you need to figure out what materials and tools you need. It is clear that the list will be different for each specific situation. It all depends on the choice of the desired model and the desired end result.

Floor lamps can be made from a variety of materials:

wood is a great option if you want to dilute the interior of the room with natural motives (lampshades consisting of branches look luxurious; if a wooden leg is used, then think in advance about protecting this part of the device from fire and decay);
plastic;
metal;
paper;
fabrics.

In the last two cases, you can create a Japanese-style lighting fixture.

In recent years, the popularity of wood products has increased as most people rely on environmental friendliness and health safety when choosing building materials.

The materials listed above are used for the lampshade (the main part of the floor lamp), but in addition to them, other important elements will be needed:

leg - a wooden rod, a metal rigid string, a pin, etc.;
the electrical wire required to connect the floor lamp to the plug and then to the power supply (ideally there should be a three-core cable);
sockets for light bulbs (you can disassemble the old lamp);
light bulb - the light source is selected depending on the operational characteristics of the finished device (for paper or textile floor lamps, LED or energy-saving bulbs with a minimum heating temperature are suitable).

LED bulbs are considered the safest light source. They are capable of producing the same amount of luminous flux as an incandescent lamp, but at a lower power (8-10 times). To fix all the elements, you will need smaller parts, including glue, wire, screws, etc.

As for the tools, you will definitely need a drill or screwdriver, a ruler, scissors and a pencil. The instructions described above may vary depending on what material is chosen as the main material for the manufacture of the floor lamp.

Base options

The base of a homemade floor device can be created from different blanks. The main condition is the stability of the future structure. The light must be firmly on a level surface, so the main center of mass must be pointed downward.

The base can be round, square, rectangular, and the larger its area, the more stable the lamp will be.

It can be made from the following materials:

Wood. To make a large circle out of wood, you can cut a piece of thick log or bar. It is not at all necessary to make a round stand. You can cut the product to the desired shape yourself. The resulting workpiece needs to be cleaned with emery paper, removing burrs. Next, the base is painted with wood stain to reveal the texture of the tree or with ordinary paint if a certain color is needed.
Gypsum. Take some plaster of Paris and dilute it with water. You will need a small container, the shape of which exactly matches the configuration of the desired base. Baking dishes have proven themselves well in this quality. Pour the solution there, place the leg of the future lamp in the center of the container and wait until it solidifies completely. Close the hole in the tube. The resulting product is painted in the desired color. Alternatively, the tube can be pasted over with paper.

To avoid the appearance of cracks and give strength to the gypsum base, it is advisable to add a little more water and PVA glue to the solution. Do not limit yourself to plaster and wood - for the base, you can take other strong materials that guarantee the stability of the lamp.

Frame fabrication

The frame is a stand, one end of which is connected to the base of the lamp, and the lampshade and all other elements are attached to the other. Choose the length of the rack at your discretion, but keep in mind that the higher it is, the more chances that the device can tip over. Also, when choosing the length, you need to take into account the location of the device.

Ideally, look for high corrosion resistant copper or steel tubing so that it doesn't rust and crumble after a year or two. Before starting work, wipe the product with alcohol or other degreasing agent to remove unnecessary stickers, etc.

The lampshade, along with the lamp, should be located above a sofa, armchair or other piece of furniture. To connect the pipe to the wooden base, drill the last hole exactly in the middle and push the pipe so that the smaller part protrudes 25-30 cm. Mark the point where the wooden base and the copper pipe intersect. At one end of the pipe, where the marking is made, drill another hole with a diameter of 5-6 mm. It will be required in order to pass the electrical cable in the future.

Assembling a floor lamp

During assembly, bond the post to the base using wood glue applied to the bottom of the pipe. Press the parts firmly together and wait for partial crystallization. Leave for a while for the glue to dry completely.

Insert the copper tube with the hole cut out towards the floor. When all the elements are assembled, secure them. All-purpose glue will do. Install an elbow on the copper pipe, designed for mounting a floor lamp and lampshade.

Pass the electrical cable through the hole you made in the previous step so that one of its ends sticks out of the elbow.

Shade

The main decoration of the floor lamp is the lampshade. The choice of this element determines what the luminous flux emanating from the floor lamp will be, and how well it will fit into the environment. In the process of creating it, you are limited only by your imagination. The main limiting factor here is the interior style of the room where the device will be used.

Any lampshade requires a base. Part of an old lamp can be used as it. Another option is to make the frame from strong, but at the same time flexible wire, which will retain the chosen shape. All side elements are attached to the base. When performing these actions, try to ensure that all joints are almost invisible.

If you did not manage to hide them, do not rush to get upset. All flaws can be eliminated with the help of various decor. Side elements can be made of plain or corrugated paper, wallpaper, Whatman paper, textiles characterized by high light transmission. Often, wooden slats are used for this purpose, allowing you to create a lamp in a rustic style. Finally, the frame of the lampshade can be pasted over with glass pendants or beads, through which the fishing line and thread were previously threaded.

The outside of the lampshade can be decorated with other elements - from rhinestones and ribbons to felt or hand-painted textiles with flowers, stars and other objects. At this stage, the main thing to remember is that clinging bulky and heavy products to the lampshade is highly discouraged.

The article described the main stages of creating a floor lamp, including the choice of material for the frame, base, lampshade and the search for suitable decor elements. The method described above can be supplemented and modernized depending on the final result, limited only by the consumer's imagination.

For the manufacture of an original floor lamp, it is not necessary to contact specialists and professional designers. It is much more interesting to show your own imagination, because who, if not you, knows better which lighting device will fit into the overall interior of the room. Moreover, a hand-made product already wins in advance against lamps that are sold in stores or on the market.