How to screw a handle on a door. Installing a door handle-lock in an interior door

This article will describe the work being done on installing latch handles on interior doors, which are by far the most popular in use.

The latch handle has the following design.

The visible part of the handle can be perfect different kind and it might look like this:

Or this way:

All such latch handles basically consist of two parts, from the handle:

and latch:

Each of these parts of the latch handle requires a separate cut into the canvas.

There are different types of latches on sale, with a latch that have an additional mechanism installed in the handle itself, which allows the door to be locked from the inside, and from the outside on the handle there is a mask for a key that allows the door to be locked. Also, such handles are available and without a latch they are not locked. Latch handles from different manufacturers have various design features that in no way can affect the process of inserting into the web. The weight of such handles has a latch on the inside, so the whole process of installing the latch handle is the same for everyone.

Therefore, if there are any differences, then because of this you should not doubt much and you should gain courage and begin to work. And you should start with the preparation of tools.

To do this, we need tools to work.

Screwdriver or hand drill.
Crown with a diameter of 50 mm on wood.
Reduced the size of 23-24mm on wood.
Pencil
Chisel
A hammer

In order to maximally facilitate and speed up the process of installing the latch handle in the door leaf, you can purchase a special kit in specialized stores.

Starting to install the latch

1. In order to proceed with the installation, it is necessary to make markings for drilling from the beginning on the canvas. If you purchased a special set for inserting such a latch handle, then this set already has a marking scheme.

If you do not have such a scheme, then the markup can be done manually. For what, approximately at a distance of 1 meter from the bottom door leaf make a mark, then measure 60 mm from the edge of the canvas along this mark and make a mark for drilling, as shown in the photo.

2. On the side of the door leaf, we also find the center and make a mark for drilling.

3. Next, we take a chisel and for the front plate of the latch on the door leaf we hollow out a recess equal to 3mm. It is better to drill the center of the thickness of the door leaf with a slightly thin drill, so that later you do not have to make markings again.

4. With a crown with a diameter of 50 mm, we make a through hole. through hole on the door leaf, it is better to do it on both sides so as not to damage the canvas.

5. As a result of the manipulations done, we get a hole.

7. As a result, we get several holes on the door leaf.

8. Insert the latch into the hole on the side of the door leaf and screw it.

With the help of a special key that should be included in the kit or any thin and flat object.

We press in the hole on the tongue.

and remove the handle.

10. After the handle, remove the decorative cap and expose the mounting holes.

12. We insert the other half, after which we tighten both halves of the handle with the screws that come with the kit.

14. We cover the door leaf and mark the place where the tongue touches the jamb, in this place we hollow out a recess for the latch tongue.

15. A plastic pocket must be installed in the hollowed out recess.

16. Install a metal lining on top of the plastic pocket and screw it on.

As a result of the work carried out door latch handle installed, the door is now ready for operation.

At what height should a door handle be installed?

The handle is an important part of the "pie" of the interior door, because the comfort and ease of use of the entire structure will directly depend on the correct installation and choice of it, and the Dverka interior door hypermarket will help with this. Most manufacturers offer doors for installation with existing handles and other accessories included.

The height of the handle in this case is standard and, in accordance with GOST, is 100 cm from the floor.

If the handle is not installed, models may or may not have grooves for attaching it. In the second case, there is a special bar in the area of the intended fixation, which allows you to install handles and a lock quickly and easily.

Here the height is determined independently, but the “limit” of indentation up and down should not exceed 10 cm.

A height of 100 cm is focused on a person with a height of 170 cm. But given that given parameter can vary significantly, the best option is to purchase a door without fittings and marked grooves and fix the handle in the place that the best way will suit everyone living in the house.

Peculiarities

To finally determine the appropriate height, you can follow the following rules:

By the wrist. It is necessary to come close to the door, lower your hands along the body. At the level of the wrist, make a mark and step back up 20 cm.
The resulting height is optimal for the person who took the measurements.
Elbow. Everything is simpler here: with a close approach to the door, the notch should be made at the level of the elbow.

If you use both methods at the same time, the result should be approximately the same in the end.

There is no need to make such measurements for each door. It is enough to set a mark on one, measure the resulting distance and measure it on other interior doors of the house.

Pen in the child's room

The height obtained as a result of the above measurements by an adult is not suitable for children - the child will not reach the handle.

On the other hand, an additional groove will negatively affect the aesthetic appearance of the structure. The best option- use the push mechanism of the handle and attach a cord to it.

The child pulls the cord - the door opens without difficulty. When the children grow to a suitable height, the lace is untied.

It is worth considering that the correct height of the handle is not the only important point.

Installing the mortise door handle

The element itself must be of high quality and reliable, easy to press. Especially for children. It is worth checking this point during the purchase. Only in the amount of product quality correct fastening will provide convenience of use of an interroom door.

Expert of the hypermarket of interior doors "Dverka" http://www.dverkadverka.ru Zakirova Victoria

How was the handle fixed on the front door?

All handles on the door, during operation, have the property of stunning and breaking.

Their repair is not so strange, and it will also apply to those who take it for the first time.

There are two ways to fasten the door: screw, through the recess and screws - self-tapping screws. Therefore, repairs cannot be expensive, and it does not require huge efforts to use them.

What tool should I stick to before I start repairing a pen?

First you need to buy a set of screwdrivers or screwdrivers and bits.

By the way, it will be much more convenient and faster to make fasteners.

You will also need a set of screws.

Fixing a broken handle attached to a fork

By connecting two equal parts of the handle on both sides of the door.

This applies to spherical or conical products.

For types presented by the carrier, the elements are installed separately. This means that half is broken, then it is repaired, and the other is in place.

The handle is then removed when the door is opened, holding the hand halfway and the other in the hole.

All design details must be entered manually.

The handle half then detaches and gets the fork set to the desired length.

How to install a latch door handle

In the same way, the whole structure turns back, here it is clean without a special tool.

Technical repair mechanism fixed in the form of brackets

In this case, you will need to buy a screwdriver or screwdriver. It should be noted that transverse bolts are better and stronger than straight ones.

The door handle is moved to cover the old grooves. Then, on the opposite side, two pairs of bolts are attached to the new holes.

Press firmly so you don't have to slide.

The top parts are also installed with screws - screws with drilling new gutters. The overlay can be attached as a square or a diamond. At the end of the work, the application is fixed.

Characteristics of the replacement of small parts parts

When replacing the spring part, the new part is strongly compressed from above, the veneer facing is installed, the veneer ring is attached and connected to the screwdriver.

Then, a delicate screwing of the rotating mechanism is performed, followed by the introduction of a spring element into it.

The button is turned by the key.

In cases where cake repairs have not been successful, it is much easier and cheaper to buy a new product.

Home »Inside» How to open door lock keyless

How to open an interior door lock without a key

Sometimes it happens that the inner door is closed and the key is missing.

You do not want to break the door leaf, because it is quite expensive, and calling a master will be an additional cost element. So, how to quickly and safely open the door without a key to the design itself?

For what reason can the doors be extinguished?

Internal door lock

Before you start opening the neck structure right away, you must state the reason why it was destroyed.

As a rule, this situation can arise for the following reasons:

The lock in the handle is simply stuck or it has turned off.
The latch is locked.
The jammed tab located in the locking mechanism is stuck.
On the other hand, there was a key in the cavity, which does not allow opening the lock.

If you want to pinpoint the cause, you need to use a wide screwdriver.

With help in different places the door leaf rises. You need to pull it out a little, and then it becomes clear where it is. Once you find an error, you can fix it.

Defective latch - what to do?

Typically, bolt failure causes unauthorized door locking.

This item may not move completely. Even when you press the pen all the time, the tongue keeps running out. If the door is too attached to the frame or slammed shut, they can no longer open.

If so, you can do the following:

Using a simple screwdriver or other hard object, gently squeeze the design fabric out of the box and gently lift it up while doing so.
In addition, to eliminate the possibility of such situations in the future, it is not superfluous if you want to spin the lever and see what is wrong with the language.
In case of need and option, it is better to replace the wrong product with a new one.

The language was not successful

There is also a situation where door structure a door that is locked will not open after repeated use.

Even if the round handle is not equipped with an additional latch, but the lock cannot be opened in the usual way, the tongue is most likely the cause of the failure.

To solve this problem, you can use a sharp tool that easily goes into the gap between the box and the door.

Then, to open the interior door lock without a key, you must follow the steps shown in:

Carefully place a ruler in a slot, plastic card, office material, or regular knife.
Orientation to the part of the door on which the door handle is installed.
The tool used to open the tool should be slightly tilted and pressed down.
How to install a handle on an inner door: Photo.

It needs to be pushed so that it can come into contact with the cut part of the tongue.
Tilt a knife or other improvised device towards the door leaf while the tongue is completely hidden in the lock. During the implementation of such measures, the handle must be in the lowered position than in the figure, and the wing must be extended in the direction in which it normally opens.

If you follow all the above rules, the keyless door will open effortlessly.

Locks on the inner door: their main functions

Before opening a doorknob without a key, it will not be superfluous if you find out what functions such mechanisms have.

Only with all the necessary knowledge and skills to solve this problem will be much easier:

Modern manufacturers could not ignore unauthorized stagnation in the doors. That's why they created a special door lock that has a lock on one side and a special opening page (button) on the back.
If the moment when the door needs to be urgently opened without the use of a key, it is enough to insert a rigid rigid object (for example, an anchor) into the hole to open the mechanism.
If there are doors with a glass frame, then in the case of a ridge, they can be carefully removed and entered into the room.

The situation could be big.

But if you can’t deal with the blocked lock yourself, it’s better to call a professional master who will solve the problem in a matter of minutes.

Add a comment

Installing a handle in an interior door with your own hands - instructions on how to install a handle

Interior doors and accessories for them, including handles, are sold separately.

Accordingly, there are no holes for installing handles in the interior door. This happens for the reason that the handles, although standardized, are still different in design and installation dimensions. Here you can do in two ways either call a carpenter, or set the handles in interior door with your own hands.

So, we install the knob-knob in the interior door. This is the most common type of handles, in my opinion, the most suitable and convenient for interior doors.

Before proceeding with the installation of handles, it is advisable to remove the door from the hinges.

If there is no one to help you, then you can not shoot. But you should prepare a chair or stool so that you can fix the door, i.e.

she became immobile.

To install the handles, you will need a drill, a feather drill, a ruler (preferably a square), a hammer, a chisel and a hole saw for large holes (see photo).

photo is red).

Fig.1. To install handles in an interior door, you will need the simplest tool that every home has: a drill or a screwdriver, a chisel, a feather drill with a diameter of 23 mm or a Forstner drill, a wood crown with a diameter of 54 mm.

First of all, we determine the installation location, or rather, the installation height of the handles.

There are no strict restrictions in this regard. Typically, the height of the handle from the floor ranges from 1 to 1.2 meters. This height is sufficient for both adults and children.

They are different for different pens. In addition, they depend on the thickness of the interior door.

Also in the instructions, as a rule, there is a template for installing handles, where all geometric parameters are indicated. We will be mainly interested in the dimensions of the holes for the pawl, the handle itself and their relative position. The diameter of the feather drill and crown depends on these dimensions.

Therefore, the necessary tool must be bought after buying pens.

It is important to note that the drill and crown must be purchased with a diameter equal to the diameter of the hole in the instructions for installing the handles. If you use a larger tool, then it is likely that decorative overlay won't close the hole. If it's smaller, then the handle just won't fit. At the same time, remaking holes for a larger size is very laborious and problematic.

Much easier and faster to do everything right at once.

Now you can directly proceed to install the handle in the interior door. For this, holes are marked for the handle itself and the dog. For these purposes, it is convenient to use a ruler as in the photo.

Fig.2. Relative to the end of the door, the handle can be displaced by a distance of 60 - 70 mm.

At this distance, mark the place for the hole for installing the handle.

Fig.3. First drill a hole for the handle.

To do without burrs and chips on the door, proceed as follows. First, a hole is drilled with a drill with a diameter of 5-6 mm. Then, with a crown, an incision is made on one side of the door with a depth of at least 5-10 mm. After that, a hole is drilled with a crown on the other side of the door.

Fig.4. At the end of the door, at a height where the center of the hole for the handle, mark the center of the hole for the latch, and make a hole using a feather drill.

The latch has a platform 2-3 mm thick. To ensure that the door closes well under the platform, a groove is cut with a chisel. It is convenient to first drill a hole, then insert the latch and mark the groove along it, and then cut it out with a chisel.

After the holes are ready, insert the dog and circle it with a pencil.

And with the help of a chisel we make a groove. This groove is necessary so that the pawl platform is flush with the door and does not interfere with opening and closing.

Fig.5. The installation of the handle begins with the installation of the latch. It is inserted into the groove and secured with screws that come with the handle.

Wrap the screws carefully and do not break the notch for the screwdriver. To simplify screwing, you can pre-drill holes for self-tapping screws with a drill with a diameter of 3-4 mm.

This groove can also be made using a milling cutter. But for this you need to pre-make a template, which is not advisable for a “one-time” installation of handles.

After the preparation is completed, install the handle on the door and wrap the screws.

Fig.6. The last step is to install the handle mechanism.

One half of the handle is installed in the latch groove. The halves of the handle are connected with screws.

Installing a door handle-lock in an interior door

It is important not to overtighten the screws, otherwise the handle may wedge.

As can be seen from the description, the installation of handles in an interior door is very simple. It is important to take your time and do correct markup. After that, holes for installation are made with special drills, a groove for the latch is cut out, and the handle is installed in place.

On average, the installation of handles takes about 20-30 minutes.

Home cosmetics

Install the handle on the inner door with your own hands

It is hard to imagine how to use an interior door without such a mandatory attribute as a handle.

At first glance, its installation can be complicated. However, with a serious approach to the task, you can independently manage the presence necessary tools and materials and proper organization of work with this task. In the presented material, let's see how the handle is installed on inner door.

Handle types

There are several types of cranks that are suitable for insertion into an inner door:

rotary;
with pressure mechanism;
without locking mechanism.

Stationary handles, which do not have mechanical operation, allow the door to be opened by pulling.

As far as pressure systems are concerned, these shutters are made in the form of a lever. In the process of pressing such a handle, the lock tongue moves inward, which allows you to open the door.

What is an oval handle door handle? Installing this system allows you to open the door without pressing the handle. Due to the circular shape of the handle, the operation is performed by turning the handle. The design can be equipped with a lock button that allows you to lock the language of the lock language.

Thus, the door can be locked from the inside.

Tools and materials

What does the installation of handles on the inner door require? Self-assembly may require the following tools:

Measuring measuring tape;
pencil;
Manual or electric drill with a pen-shaped nozzle;
screwdriver;
chisel for woodworking;
a hammer.

Interior door handle height

Before inserting a lock into an interior door, you must determine the optimal location for installing the handle.

To do this, it is enough to simulate the opening of the door in order to consider what height is most suitable for each individual user. As practice shows, right decision is to place the handle on the inner door at a distance of at least 1 meter from the floor plane. The presented images are optimal for both adults and children.

Cutting holes for handle

After you find the necessary tools and determine the location of the building, you can proceed directly to creating a hole for installing the mechanism.

First, mark the height of the future handle on the plane of the door and its end. This is necessary to determine the exact location where the hole will be punched with the double sided drill bit.

In order not to interfere with the calculations, it is enough to take a blocking mechanism, and then, using a tape measure, we measure the distance from his eye to the visible edge.

The parameter must be marked at the pre-selected height on the door leaf. As soon as the appropriate marking appears, you can continue to select the appropriate drill material.

At the end of the holes you need the diameter on the plane and at the end of the door leaf, here you need to attach the opposite parts of the handle structure.

If the thickness of the plane does not allow installation, excess wood should be removed with a chisel. Then you need to scrape the fabric on both sides until the handle engages.

Bolt Assembly

After completing the previous work, the latch should be installed in the prepared hole. Installing doorknob handles on an interior door involves attaching it to the door leaf in an open hole using fasteners that are attached to the product kit.

It is appropriate to work with a screwdriver.

How to install a handle on an interior door

However, in the absence of the latter, you can use a regular screwdriver.

After strengthening the key part of the structure, he for a long time includes a core that is reinforced with a screw. In order not to have problems with the base assembly, the key must be inserted in advance by moving the mechanism lock mechanism to the closed position. Only then should the screw be tightened.

Installing a door handle on an interior door

Direct insertion of the handle into the pre-assembled structure is the most a simple step work.

It is enough to insert a square rod into the corresponding hole of the locking mechanism.

The next step is to secure the handle with a buckle to one side of the door. To do this, you can use self-tapping screws or use zip ties. Once the first handle has been successfully assembled, similar operations must be carried out with the other part of the structure, which must be installed on the back side of the door leaf.

This will establish a connection between the two elements of the system.

Installing the keypad insert in the door frame

In order to install the handle on an interior door, it is considered ideal, it is necessary to make an appropriate hole to enter the locking part of the lock in the door frame.

Do not use calculation errors that allow you to use toothpaste on the tab along the vertical edge. When the door leaf is closed and the handle is released, the blocking element is connected to a part of the box.

The remaining toothpaste label will tell you where to make the hole under your tongue.

Using the method described above is the optimal solution for determining correct location panels. Experts also resort to this causality.

The formed imprint from the protruding tongue of the neck should guide a stable outline with a pencil. Then use a drill and chisel to enter the hole in the cork, then a metal plate with a hole.

In advance, you also need to place holes for fasteners in order to secure the plate to the door of the door.

When you create everything required holes, it is enough to fix the plate in the corresponding section. To fit snugly against the door lid, metal element must be firmly screwed to the wooden surface.

In the end

Therefore, we looked at how the handle is installed on the inner door.

This material provides an example of how to cut a simple mechanism into wooden plan. Now you have enough knowledge to solve your problem on your own, without resorting to external help.

Installing door handles with your own hands is a simple process, but it requires certain knowledge and accuracy when doing the work. In this review, we will look at the three most common types of pens and understand the advantages and disadvantages of each of the options. We need to choose optimal solution and install it according to the instructions below.

Currently, there is no shortage of pens, the choice is so large that it can be a problem to determine the most suitable option.

Stationary;
Push;
Swivel.

Stationary handles

The oldest type of product that has been used for thousands of years.

First, let's look at their main advantages:

Simplicity. There are no elements in the design other than the handle itself and the mounts. Thanks to this, installing such options is much easier than any other. The set of door handles includes only handles and fasteners, which is also important, because you do not have to assemble an ingenious mechanism and figure out how to set it up and install it correctly;

Reliability, due to the simplicity of the design and the absence of moving mechanisms in it, there is simply nothing to break in such products. The only problems you may encounter are damage to the coating over time or loosening of fasteners if the handle is pulled frequently. It is possible to break such a structure only if it is made of low-quality material;

Classic look. Such handles belong to the classics, therefore they are widely used in the arrangement of the corresponding interiors. Very often they are made in a luxurious style and covered with compositions that imitate patina or precious metals.

Also often found forged options, they too can be very, very skillful;

Ease of installation. Fixing the door handle is within the power of any person - you just need to determine the location of the products, align them relative to, after which the self-tapping screws that come with the kit are screwed in;

Various manufacturing materials. You can purchase products made of steel, brass, bronze, aluminum, plastic and composite materials. Wood stands apart, very authentic and unusual handles are obtained from it, very often precious wood is used for their manufacture.

Of course, there are also disadvantages, the main ones are:

No locking mechanism. To close such a door, you need to install either a spring latch or a latch, and this is not always convenient. That is why such products are used less often than others and are most often placed in country houses, baths and outbuildings;
Small selection. Although the range of this product group is rather big, only a few types of pens are usually found on sale. Most often you have to buy suitable options under the order and wait for delivery for some time.

rotary knobs

This type of product is quite common, and its main feature is that the door opens by turning the outer part.

This is a fairly simple and convenient mechanism, let's analyze its main advantages:

Note! The round shape of the handles has several names -. The difference between them lies in the presence of a locking mechanism, which is activated by turning the handle itself to the left or right. The handle-button does not have it, therefore it belongs to stationary views.

Interesting appearance . Most often, handles are spherical or cylindrical in shape and look good on doors. There are many options for execution, so picking up something for your doors is usually not difficult;
Availability of original designs. They themselves are an adornment of any interior and can have a wide variety of colors or patterns on the surface - there are even crystal options, their price is high, but their appearance is luxurious;
compactness- This option takes up little space and is well suited for limited space. In addition, the mechanism is also compact, which greatly simplifies its insertion into the door leaf;
Safety. If you hit such a handle, then the likelihood of injury is low, unlike push options. Therefore, such products are often put by those who have small children.

Now let's deal with the disadvantages of rotary knobs:

Low coverage reliability. because of active use the decorative layer begins to collapse, which worsens the appearance, and the accessories for door handles are not sold separately, and you will either have to use peeled products or change them to new ones;

Advice! As practice shows, chrome-plated products are much more reliable options in gold and bronze. Keep this in mind when choosing a specific solution.

Poor workmanship. Most of the products on the market are not very reliable and durable. Repairing door handles is not a pleasant occupation, and spare parts are not always available, especially if you have some unusual option. In order not to have problems, try to choose products from those manufacturers that are widely represented on the market, at least there will be no problems with repairs;

Impossibility to install other types of handles. If you decide to put a rotary option, then keep in mind that during installation you will have to cut a large hole in the door leaf. After that, putting a lever or another option will not work, you will have to constantly put the same type of structure.

Push handles

This is without a doubt the most popular and common option, which is found literally everywhere. It consists of two L-shaped handles connected by a square, with which the door latch opens when pressed.

As for the main advantages, they are as follows:

Ease of use - it is very easy to open and close the doors, and if the rotary options need to be moved by hand, then the pressure ones can also be opened with your elbow if your hands are busy. Most often, the handles are ergonomically shaped, which is also important, but to appreciate the convenience, it is better to buy products where there are showcases for door handles so that you can hold on to them;

A huge range of products, you can find options for all kinds of colors and designs. You can decide for yourself which color of door handles to choose, which significantly expands the possibilities of decorating the room. There are also budget options middle segment premium products, everyone will find a suitable solution;

Maintainability. Most often, the mechanisms are interchangeable, so there are usually no problems with repairs. And in terms of reliability, this option looks preferable to the one described above, since the lever unlocking system is more wear-resistant and durable.

It should be noted that such products are of two types:

Socket handles. Mounted on a small base, under them you can use different locking mechanisms. If a latch or lock is needed, then an additional socket is placed below, it has the same coating as the main element;

Handles on the bar are more often used on entrance structures, but there are also options for interior doors. In them, the base of the handle is a bar, in the lower part of which there is a keyhole or latch.

Of the minuses, one can only single out a more complicated installation process, since the work requires accuracy, and any errors can lead to damage to the door leaf.

Description of the installation process

Now let's figure out how to put the handles yourself. Two options will be considered - rotary and pressure structures. There is no point in disassembling stationary ones, everything is simple there - you determine the installation location, and screw it on.

Installation of rotary handles

To get started, you should stock up on everything you need.

Naturally, you need a set of door handles, the following tools will also be used:

Feather drills;
Drills for wood or metal;
A hammer;
Chisel;
Screwdriver;
Roulette, pencil and square;
Drill;
Wrench;
Crown on wood.

Installation instructions for door handles of a rotary type look like this:

Illustration	Description
	The location of the element is determined. European standards for door handles and domestic GOST prescribe a height of 1 meter, it is considered convenient for a person. Therefore, first of all, draw lines a hundred centimeters from the floor.
	Your lock is taken, and markings are made on the door leaf. It makes no sense to give specific recommendations - it all depends on the model and size of the pen. Read the instructions, and everything will immediately become clear to you. Usually you need to drill two small holes for the through fasteners, and one larger one for the mechanism. Advice! It is better to drill half the thickness of the web on each side, this is the most accurate way.
	After finishing the work, you should get something like this - a large hole in the middle and two small ones on the side. The main thing is to ensure that drilling is carried out on the same line. Otherwise, an offset will result, due to which installation can become very complicated.
	If you can purchase a special template for inserting door handles, then the work will be greatly simplified. You will need to set it at the required height, fix it on the canvas and drill holes in the right places. No measurements and no error. But templates are not suitable for all pens, so check in advance if this system can be used in your case.
	A hole is also drilled under the core, its diameter is usually 25-27 mm. It is important to find the middle at the end of the door leaf and keep the drill strictly horizontal during operation. If anything, you can make certain edits, the main thing is not to move the hole too much.
	Insertion of door hinges and handles is impossible without making grooves for the elements, in our case it is necessary to make a recess for the latch platform. To do this, the mechanism is placed in the hole, and its outer part is outlined along the perimeter. Then, using a chisel, a layer of wood about 3 mm thick is removed. First, punch the material around the perimeter, and then remove layer by layer until you get the desired result.
	In the process of sampling the recess, constantly check how the latch becomes. It is better to do it once more than to overdo it and shoot too much. The work is simple, but painstaking, it is important to do everything as carefully as possible, the appearance of the structure depends on it.
	After the latch is perfectly in place, it must be fixed with the screws that come with the kit. Tighten them carefully so as not to turn the fastener in the material and thereby weaken it.
	The design of the handle is divided into two parts, one of them will have mounting bushings, which is what we need in the first place.
	First, a part with bushings and a square is placed under the latch. It must be carefully positioned and pressed firmly to make sure that everything is in order and the socket fits snugly against the door leaf.
	The handle is placed on the other side, the holes on it are combined with the bushings. Then two coupling screws are screwed in, which will hold the structure. The work is almost finished, but most likely you still have spare parts for door handles, namely the counterpart and fasteners for it. Let's figure out what to do with it.
	Close the door and note at what level the latch is located. Then attach the counterpart according to the marks and mark the place where you need to drill a recess for the tongue. Lastly, the bar is screwed to the door, this is the end of the job.
	The photo shows how it looks right assembled structure. Everything is neat and secure. The door can be used.

Installing lever handles

Now let's deal with this option. Naturally, the technology can be different, since the production of door handles is established in many countries and everywhere there are standards. We will analyze the most common latch option, which is great for interior doors.

Illustration	Description
	Produced marking work. Above, we said that the standard installation height of door handles is 1 meter, although you can arrange them as you like, it all depends on you. With the help of a tape measure, a clear mark is placed.
	To clearly mark the door on both sides and from the end, the easiest way is to use a construction square. It is pressed tightly against the edge of the canvas, after which a line is drawn. So you will achieve perfect marking accuracy on both sides of the door leaf.
	Now you need to decide where to drill a hole for the latch square. To do this, the latch is applied to the door so that the drawn line is in the middle of the square hole. Keep in mind that the mounting plate will sink into the surface, so position it flush with the end of the door. Do the same for the other side of the door.
	This is how your result should look like. There is no need to chase the accuracy of the markup, it is important to determine exactly where the center of our hole will be, anyway we will make it a little larger than the size of the tetrahedron so that the element can move.
	A hole is made using a drill or screwdriver. For work, a drill with a diameter of 12 mm is used, you can take the 10 mm option, but then you have to slightly drill the hole so that a tetrahedron enters it. The work is done as follows: first, on one side, you need to go deep by about half the thickness of the canvas, then the same is done on the other side, and then you can go through. This is the most accurate way, if you go through on one side, then there is a high probability of displacement.
	This is how the result of the work looks, everything is clear and even. Make sure the square fits and can spin inside.
	Now you need to mark the end for the core. To do this, a tetrahedron is inserted into the hole, a core is put on it and marks are made from above and below. Next, you need to mark a point strictly in the middle of the canvas, this will be our main guideline in the first stage.
	First, a hole is drilled in the middle. Any suitable drill is used for work, but usually a thicker option is taken so that later there is less work to expand the recess with a chisel.
	Since the core has a rectangular or square shape, the hole for it is completed with a chisel. Just knock out a recess according to the required size to the desired depth. This is perhaps the most time-consuming and lengthy stage. It's simple, but it takes a lot of time.
	After the hole is made, the latch is inserted and a notch is marked, which must be made for recessing the mounting plate. Everything is simple here: align the element so that it is parallel to the door leaf and carefully draw lines around the perimeter.
	In order not to remove the excess when removing wood, first of all, you need to cut through the material along the perimeter to a depth of 3 mm. It's simple: the chisel is attached to the surface, after which it must be hit 2-3 times with a hammer. And so around the perimeter.
	The removal of wood is carried out carefully and little by little - a little tweak later is easier than removing too much. Periodically insert the latch to control where and how much to remove. If necessary, you can cut the tree around the perimeter again.
	Next, you need to make holes for the fasteners. They must be through, as the handle is pulled together with special fasteners. Measurements are made and holes are drilled at the required distance. Everything is done here, as in the case above: work is done on both sides at half the depth of the door leaf.
	The core is fastened with two screws, after which you need to check its performance. Insert the square and turn it, the latch should move with little resistance.
	The handles are aligned along the holes, after which special screws are screwed into them, they enter the sleeve and securely fix the structure on the canvas.
	For reliability, it is screwed into the handles under two more self-tapping screws. They are included in the delivery.
	Lastly, put decorative covers on sockets, they cover the fasteners and give the handle a more attractive look. This completes the work, it remains to put only the counterpart, this process is described above, it makes no sense to repeat here.

Conclusion

Now you all know about the types of door handles and how to install them. As you can see, putting the handles is not as difficult as it seems at first glance. You must follow all the recommendations and do everything very carefully. The video in this article will help you understand the issue even better, watch it if you are going to do the work yourself.

Sections of the article:

Today it is difficult to imagine an entrance or interior door without a handle. Of course, there are some types of doors that do not require this element. But in most cases, the handle is simply necessary for the convenient operation of the door leaf. What are the handles and how to install handles on interior doors on your own?

Types of door handles and methods for their installation

Door handles are classified according to several criteria. According to their purpose, they can be divided into those that are not responsible for the operation of some other device and those that are installed in combination with a latch or lock. by the most simple type handles are considered stationary models. A feature of such products is the ease of execution. Stationary handles are rarely distinguished by special grace or elegance.

Such fittings rotate or spin only if it is out of order. The installation process of stationary handles is not very difficult. special attention description of the installation of such products should not be given. They are simply fixed on the door leaf with screws or screws. Another option for installing stationary handles is to secure them with a threaded stud. The last way involves drilling a hole through the door leaf at a height of 800-900 mm from floor covering. Well, then everything is elementary - a hairpin is inserted into the drilled place, onto which handles are screwed on both sides of the door leaf.

Another type of handle is used in combination with a lock or latch. The installation process of such products is more complicated, due to the presence of a locking system. These knobs are either rotary or push. The first are made in a spherical shape and they are also called knobs. Part of their design is a simple locking mechanism. In addition to the above differences, door handles differ in the type of material from which they are made, as well as in their design characteristics.

There is also a number of not particularly important nuances which allow the door handles to differ from each other. To describe everything existing species and subspecies of these attachments, a separate material will be required. In this case, it is more expedient to deal with the principle of installing one of the main types of handles, namely fittings with a locking mechanism in the design.

Required tool

To install a door handle with a latch, you will need to prepare some tools in advance. So, during the installation process, you will need an electric drill or a screwdriver, a hammer, a chisel and a chisel, as well as a set of drill bits different diameter. In addition, it is necessary to prepare a sharpened pencil, measuring tape, square.

It would be nice to say that the best tool to create a seat for a decorative latch trim, a manual milling machine is used. But, given the fact that this equipment is rarely found on the farm, with self installation handles on the interior door will have to be content with chisels and a hammer. It should be emphasized that the chisel is a rather clumsy tool and the quality of the work performed with its help directly depends on the experience and skills of the master. When installing the handle, it is very important not to damage the decorative coating of the door leaf. Therefore, wielding a chisel and a hammer will have to be as accurate and verified as possible.

Door handle installation guide. Process Features

The first step is to get ahead of the place to install the handle. There is a certain height standard at which it is recommended to fix such fittings. This parameter is 800-900 mm from the floor covering and was introduced based on the average height of a person. Of course, when installing the handle on the door leaf, one should take into account the physiological characteristics of the inhabitants of the dwelling. If we are talking about short people, then standard height need to be reduced. For tall residents of the house, on the contrary, it is advisable to fix the handle above the established norm. The process of installing a door handle consists of several successive stages, which will be discussed below.

The first step is to mark the place under the handle. This is not the most difficult operation, which includes a number of steps. First you need to put a mark on the door leaf. This is where the handle will be placed. Then this mark needs to be moved to the center of the end of the door leaf. In this place it will be necessary to drill a hole for the latch latch. To unmistakably get ahead of the location of the handle itself, you should measure the distance from the edge of the latch to the middle of the hole in the mechanism into which the square fastening rod will be inserted. Then the resulting size must be indicated on the door leaf. As you can see, the entire marking process for installing a latch handle comes down to obtaining these two points.

At the next stage of installing handles on interior doors, you need to drill holes. The first step is to prepare a place for a square fastening rod on the side of the door. After this hole is ready, it will be possible to start creating a recess on the end side. So, to drill the side of the door leaf, you will need an electric drill and a feather drill with a diameter of 25 mm. Drilling is required on both sides. This will avoid damage decorative coating door leaf. After the drill appears with reverse side door, you need to continue drilling in the opposite direction. When this hole is ready, you can start creating a recess at the end of the door leaf.

To do this, use a drill with a diameter of 22 mm. After drilling the first hole, it is necessary to make a sweat from the end of the door for a decorative lining on the latch. To do this, it is necessary to install the mechanism in the prepared end hole and outline the plank with a sharp pencil. After that, the latch can be removed with a hammer and chisel right size create a shallow groove for flush installation of the decorative trim.

by the most the best option will be used for these purposes manual router. But such a tool is rare for ordinary apartments, but there is a chisel and a hammer in almost every home.

In the future, installing a handle with a latch on the door involves assembling the entire mechanism inside the canvas. To do this, first of all, a latch is inserted into the door through the end hole. The mechanism is fixed with a pair of screws or screws. By the way, it will be emphasized that during this operation it is advisable to control the performance of the latch. It should not jam, which sometimes happens due to wood dust and shavings getting inside the mechanism. To avoid such troubles, it is recommended to properly clean the end hole before the final fixing of the latch.

The next operation is the installation of a square rod. There is also nothing complicated here. It must be passed through a square hole in the latch to the side of the door leaf. After that, a handle is put on the square on one side of the door. By the way, the kit comes with one right handle and one left handle. It is important not to confuse them here. The handle is put on the square and fixed on the door leaf with screws. Usually, three fasteners are provided for each side.

The second handle is installed on the door leaf in the same way. After fixing both handles, it is necessary to verify their proper functionality. If everything, including the latch, works as it should, then you can proceed to the final phase of the installation. It consists in winding special decorative caps onto the handles, which hide from the eyes the places where the fittings are fixed and give the product aesthetics. In addition, under the handle you will need to tighten a hidden screw for fastening. It is usually screwed in with a hex wrench.

This completes the installation of the handle on the interior door. To use the mechanism for its intended purpose, it remains only to install the counterpart in the door frame. This operation is performed according to a certain technology, which will not create difficulties even for beginners. The first step is to transfer the location of the middle of the latch to the door frame. This should be done with the door leaf not tightly closed. Then, in the part of the box where the door closes, it is necessary to drill a hole about 10 mm deep exactly in the center. A decorative overlay is installed on top, which should come with a latch. It is not necessary to deepen it into the body of the door frame, just screw it on. After that, you need to check how the latch works.

On this, the process of installing a door handle with a latch can be considered completely completed. According to the same algorithm of actions, the installation of a handle with a lock is carried out. The difference in these two processes is only in the size of the end seat and the need to drill another hole on the side surface of the door leaf. In this place the locking system cylinder will be installed. Otherwise, the process of installing the door handle is similar.

Interior doors are sold without fittings. Therefore, the purchase and installation of door handles is carried out separately. To do this, you can use the services of a carpenter or insert it yourself.

Types of door handles

When choosing accessories, you need to know what types of handles are, and how they differ from each other. The variety offered in stores allows you to choose them for the style of the room and ensures ergonomic use. Depending on the installation method, products are divided into two classes:

invoices;
mortise.

Overheads are attached to the surface and, as a rule, there are no difficulties with them. And mortise ones require preliminary preparation of a hole in the door leaf.

Mortise products can be of two types:

Rotary, they are also called knob knobs, which, when the handle is turned, open or close the latch that holds the interior door closed. In most cases, they are made in the form of a ball or disk.
Pushers work on the same principle as rotary ones, only the mechanism is activated by pressing the handle. As a rule, they are sold together with a lock or latch, hence another name for them - lever latch handles. Fittings with a push mechanism are widely used for both interior and exterior doors.

Which type of product is better to choose depends only on your preferences. You should also consider the style of the room. Designers advise buying them for all doors in the same room the same.

The height at which the door handle should be is not clearly fixed by any standards. On average, it is located at a distance of 1 meter from the floor. This value can fluctuate up or down depending on your preferences. It may also depend on the height of those who will constantly use the door. When installing, you can build on the level at which other handles in the room are located so that their height is the same.

Tools

In order to insert a handle into an interior door, you need to have a certain set of tools. It includes:

tape measure, square and pencil;
chisel;
screwdriver, drill;
drill, crown.

Using all the necessary tools greatly facilitates the work process. It is quite possible to embed fittings without a screwdriver and crown, but in this case, the work will take much longer.

Fittings are ideally installed when the canvas is removed from the hinges. If this is not possible, then you need to securely fix it in order to qualitatively and evenly perform marking and tie-in.

Before starting the tie-in, carefully study the instructions for the door handle. All sizes are listed there, and you will know what diameter of the crown and nib you need for work.

The instructions below will help you put the handle on the door leaf and avoid mistakes. And for those who first encountered such a case, it will be useful to watch a video on this topic in order to have a visual idea of \u200b\u200bthe upcoming installation work.

Step-by-step instructions for installing a door handle

Canvas marking.
Drilling a hole for the handle and lock.
Lock installation
Handle notch.
Luke marking.
Cutting a groove in a hole

Let's pay special attention to each stage of work, analyzing it in detail.

Web marking

Installation begins with markings on the door leaf. First you need to decide what height will be chosen for the location of the handle. With the help of a square, tape measure and pencil, places on the canvas are marked in which holes need to be made. To do this, we measure the required distance from the floor and draw a horizontal line with a pencil, first on one side, and then transfer it to the end and the other side.

At the end in the middle of the drawn line, we mark the place where a hole will be made for the lock tongue. On the same line on both sides at the same distance from the beginning of the canvas - this is usually 60 mm - we mark the places where the handle itself will be inserted.

Drilling a hole for the handle and lock

Using a drill and a crown, we make a hole for the door handle. You need to check on each side of the canvas to a depth of half the thickness of the interior door. For convenience, experts recommend outside crowns make a mark with a marker. First, on one side, we drill to the required depth, and then on the other until the drilling is complete. This is done so that the crown does not go to the side and so as not to damage the appearance when selecting material for fittings. You need to hold the drill at an angle of 90 degrees and not allow it to deviate either vertically or horizontally. With the help of a chisel, we smooth out all the bumps.

We make a hole for the lock with a drill and a pen. Work should be carried out carefully, since the distance between the pen and the corner of the butt is not at all large.

Some experts prefer to first make a hole for the latch, and then for the handle. In what order you will do it does not matter.

Lock installation

To install the lock, it must be inserted into the corresponding hole. Overlay, apply on top and circle it around the perimeter with a pencil. Now you need to use a chisel to select the material to a depth equal to the width of the lining in order to drown it in the canvas. For convenience, you can use several chisels of different widths.

The trim is attached to the door with screws. Holes for them are recommended to be made in advance using a thin drill, attaching an overlay and marking the right places with a pencil.

Handle inset

There are products in which the screws are outside. You don't need to parse them. Putting one part in place, you need to get into the holes of the latch with two guides, in which threads for bolts are provided. Then you need to attach the second half and tighten with bolts. You need to twist them evenly so that the handle works well and the latch easily returns back.

Products in which screws are hidden must be disassembled. Included with them are instructions and a key for disassembly. The handle can be easily removed if you find a stopper on it and press on it with a key. The collapsible part is bolted, after which the handle is put in place. Don't use force, assembly should be easy if you do it right.

Loot marking

After installing the handle, you need to make an appropriate hole for the tongue in the loot. Therefore, first of all, it is important to correctly mark the door so that the door closes well and the lock enters the groove without effort and friction.

We close the interior door and mark the top and bottom of the tongue with a pencil on the loot. Using a square, we determine the exact middle of the castle and mark this value on the loot. We make a hole with a drill and a pen and remove excess material with a chisel.

Cutting a groove in a hole

Before screwing the trim, it is important to check how the door closes. This will allow you to be sure that the groove for the tongue is made correctly and there will be no difficulties during operation. When closed, the door should have a slight play, that is, it should stagger a little. This is necessary because the thickness of the latch striker metal will be added to the groove.

The strap is fastened flush with the loot. To do this, as with the installation of the castle, it must be drowned in the loot to the required depth.

A slight play may remain even after you have screwed on the pad. This defect is easy to fix. The striker always has a tongue with a small hole for a screwdriver. It is designed specifically to bend it. Using a flathead screwdriver inserted into this tab, you can adjust the doors by bending it slightly.

The entire described process can be clearly seen on the video on fitting fittings into interior doors. The installation of the handle can be considered successful if it turns easily and the latch enters the groove without friction and effort.

You bought, say, a new interior door and decided to assemble the door frame yourself and install this very door without any experience. Well, it happens that some things have to be done for the first time. The most important thing here is to take your time and be attentive to what you are doing.

When for the first time I had to install interior doors in one of the apartments, I must admit that when sawing the first box, I made a mistake. As a result, I had to buy a new set of boxes. Ever since then, I have been very attentive and accurate when doing the work of assembling and installing doors.

When cutting elements door frame there is no room for error, you need to remember this. As the saying goes, measure twice, cut once!
So, the door has been brought in and is standing in the corridor, perhaps for the second week already. There is nowhere else to put it off and it's time to get down to business. A reasonable question arises. Where to start?

Marking the door leaf for tie-in

You should start by marking on the door leaf the place where it will be recessed latch handle. The door leaf is, in fact, the door itself without additional elements, boxes, dobors and platbands.

To begin with, decide in which direction the door will open, the position of the bevel of the latch tongue will depend on this. Now you need to determine the height at which the door handle will be located. As a rule, the handle is cut at a height of 90-100 cm from the floor or threshold. In rooms, of course, there are no thresholds. But in the bathroom or toilet, they are very possible.

In a box with door handle, you will almost certainly find instructions with the dimensions for which you need to markup. Often the dimensions are indicated on the box itself. Ordinary handles are almost always installed in the same pattern. In shops building tools special kits are sold for inserting handles into the canvas of interior doors. The set consists of a pen drill, 23 mm in diameter. and crowns for wood, with a diameter of 50-54 mm.

So, mark a distance of 95 cm on the end of the door leaf. Using a square, draw a clear line perpendicular to the end of the leaf. Mark the middle on it and pierce it. You can pierce with any sharp object, an awl, a nail or a self-tapping screw. At this point, you will need to drill a hole for the latch. But don't rush, it's not time yet!

Need to continue pen markings, or speaking professionally, for knoba. To do this, you need to continue the line at the end further to the canvas itself on both sides. This must be done strictly perpendicular to the door leaf, using a square. It would be useful to recall that the pencil must be sharply sharpened.

Here you should pay attention to one detail. The handle can be positioned at a distance of 60 or 70 mm. from the edge. To do this, the adjustable latch length design allows. Decide which distance suits you best, and mark the desired distance on both sides of the canvas on the lines drawn earlier.

Please note that on a blank canvas, that is, on one that does not have decorative elements in the form of planks, glasses, and other things, the distance from the edge at which the handle will be embedded is not critical. After all, the canvas is absolutely flat and smooth. But presence decorative inserts may limit the location of the handle. And if you decide to embed the handle at a distance of 70 mm. from the edge of the door leaf, make sure that the handle does not block decorative elements. Otherwise, make a mark of 60 mm. from the edge.

Drilling a hole for the handle

drilled first pen hole, then for latches. It is more comfortable. Firstly, when you start drilling the end, you will know exactly when to stop, and secondly, all the chips will simply fall down when drilling the end, and you will not need to sweep or blow it out with a vacuum cleaner, which is very inconvenient.

So, take a drill, fix a wood crown (50-54 mm.) into the chuck and start drilling from one of the sides, having previously marked the marked point. Do not try to drill through the entire canvas "in one go". Firstly, you will not have enough depth of the crown itself, and secondly, the teeth of the crown will become clogged with sawdust, the crown will get very hot and burn the tree, and the deeper, the stronger. We just needed a fire!

Having drilled 4-6 mm, without turning off the drill, pull it towards you, removing the crown from drilled hole. There is no need to turn on the reverse and generally make sudden movements. Everything should happen smoothly, but surely.

Clean the teeth of the crown from sawdust. Be careful, it can be very hot! It all depends on the material of the door leaf and the degree of its humidity. The denser the material and the wetter, the more the crown heats up. But the crown with blunt, worn teeth is heated most of all. Never use this! Buy a new one is my advice.

After cleaning the teeth of the crown, and allowing it to cool if necessary, immerse it in the place where it was taken out some time ago, and continue this important mechanical operation to obtain the much-needed hole. As I already mentioned, the crown, due to its limited depth, will not allow the canvas to pass through. Having drilled halfway, you should go to the other side and repeat the whole operation again. Here you need to be more careful. Approaching the middle of the canvas, do not press hard, let yourself enjoy the last seconds of this exciting process! Otherwise, you run the risk of slipping through the crown and hitting the door leaf hard with a drill. And we don’t want to scratch it or leave a dent, right?

Drilling a hole for the latch

Let's move on to the next step. We take out the crown from the drill chuck, not forgetting about its elevated temperature. We clamp a feather drill with a diameter of 23 mm into the chuck. Pay attention to the photo. It shows that the size of 25 mm is stamped on the drill. But be calm, no cheating! It’s just that I didn’t have a drill of the required diameter, and I used a “perk” of 25 mm, after grinding its edges to the desired diameter with a grinder. Here's a little trick, take note.

Drilling must be strictly perpendicular to the end of the door leaf. At first it seemed to me that it was very difficult to control. I mean perpendicularity. But then I realized that this is easy to do, just watching how evenly the drill selects the circle. This is especially noticeable at the beginning of drilling, and having gone a little deeper, you can hardly worry that the drill will deviate from the set course. But this does not mean at all that you can relax and look not at the drill, but at the cat sprinkled with sawdust passing by.

Installing a latch for an interior door

Well, what! The drilling of the holes is completed, now you need to drown the latch bar into the end of the door leaf so that it is “flush” with the plane. Professionals do it with a manual milling machine, but not everyone has one, so you have to work with a hammer and a chisel.

Insert the latch into the hole and circle it with a sharpened pencil. In order to keep the plank in place during the stroke, I usually immediately drill holes for the fastening screws and twist them slightly, fixing the plank. After circling the bar, remove the latch and grab the chisel. Do I need to say that the chisel should be not just sharp, but very sharp?!