Gas hob worktop. How to install the hob in the worktop with your own hands

Thinking about self-production kitchen furniture? Then it's time for you to find out that making it is only half the battle, and the second half of this business is to complete the furniture with all kinds of equipment. These are both built-in washing and dishwashers, and a sink, and an oven, and, of course, the hob, which will be discussed in this article. Together with the site okuhne.net, we will deal with the question of how to install the hob with our own hands and how to connect it to the home gas pipeline and electrical wiring.

Hob installation photo

Installing the hob: marking the installation site

Marking is perhaps the most important stage of work associated with installing the hob with your own hands, which, oddly enough, has the most nuances. Judge for yourself - the whole appearance of the kitchen depends on how clearly and accurately you can mark, and then cut a hole for the hob. This is exactly the case in which an error of one centimeter can be irreparable - you should always remember about the cost of the countertop. Buying a new one isn't all that cheap. The fact is that the panel itself must fit clearly above the curbstone, and there is practically no margin in width there.

There are two ways to mark the bore hole - you can simply lay it on the tabletop, center it on the peephole and circle it with a pencil, or go the way of professionals and calculate everything down to a millimeter. Naturally, it is better to choose the second option for solving the issue, since in this case the chances of making a mistake are minimal. This is done as follows.

Now it's just a small matter - cut and install the hob into the hole. We will talk about this further. For those who do not like to read and delve into what has been written, we attach a video on installing the hob in the worktop.

Installing a gas hob: two ways to cut a hole

You can cut a hole for the hob using three different electric tools - a jigsaw, a drill or a hand-held milling machine. The most accurate and beautiful cut is obtained when using hand router, but you don't even need to ask about the presence of him in the home workshop of a person who is not associated with construction. Not everyone can find a jigsaw either, but at least it is not very expensive, and you can buy it for these works. Well, almost every household man has a drill. Let's start with it, but first I will warn about the quality of the hole obtained with the drill - it can be said to be disgusting. It is quite difficult to seal torn edges, but this must be done, and problems will arise in this regard. In principle, they can be solved, but more on that later.

After the hole is ready, it is imperative to waterproof it - if water or even just moisture gets into the end of the countertop, there is a very high probability that the material from which it is made will swell and the countertop will deteriorate. Typically, the end of the cutout is treated with silicone. If you cut a hole with a drill, then it will be quite difficult to do it efficiently - you have to tinker.

Installing the electric hob: fixing and connecting

To make it easier to understand how the hob is installed in the hole of the countertop, we represent it in the form of a sequence of work - so to speak, in the form of a small, but clear instructions on the installation of the hob.

Basically, that's it. The electric hob is mounted in exactly the same way. The only exception is the absence of a gas hose in it. There may, of course, be other nuances - for example, if we talk about a hob dependent on the oven, then the installation process here looks a little different. To begin with, the oven is installed, and then the panel, which is connected directly to the oven itself.

Basically, that's it. Now judge for yourself whether this work is difficult or not. You will cope with it yourself, or perhaps contact the specialists. In general, based on experience, I can say that most people who are wondering how to install the hob with their own hands, cope with this work easily. In fact, it is not difficult, and all that is needed for the successful completion of the case is to clearly observe all the subtleties and nuances.

An integral part of the kitchen is gas stove followed by ideal option the husband is standing and preparing breakfast for his wife. Non-classic gas or electric stoves, and the hobs. Their convenience lies in their compactness and the possibility of separate installation. oven... But installing them on the countertop will make an inexperienced master sweat. Is it possible to fix such a module on your own and what is needed for this? This will be discussed in the article.

Varieties of hobs

All hobs can be divided into two large groups. The power source unites these groups; it can be:

• electricity;

By outward appearance hobs that are connected to the gas main are practically no different from conventional slabs... An option for such modules can be an automatic start system, which can be autonomous or dependent on electricity. In the first case, it is represented by a piezoelectric element, which in the right moment gives a spark. Gas hobs may vary in size for better usability.

Electric hobs can be of two types:

• classic;
• induction.

In a classic hob, the role of a burner is played by a heating element or another a heating element... Such a module is cheaper and is not particularly economical. Induction hobs are the dream of every modern housewife. The essence of the operation of the product is to heat the product due to electromagnetic field... Moreover, if you put your hand on a working burner, then you will not feel anything. A metal pan with a thick bottom is required for the product to function properly. In this case, the material from which the dishes are made must be magnetic. The installation process for each of these surfaces is very similar. The difference lies only in the need to connect the gas hose for the first version of the stove.

Installation tool

The entire installation process does not take much time and requires a tool that you may already have in your arsenal. home master... Among the main tools are:

• screwdriver or drill;
• electric jigsaw;
• roulette;
• marker or pencil;
• silicone sealant.

Additionally, you may need a level or a long metal ruler to make it easier to draw straight lines.

Preparatory stage

If it comes on the hob, which is powered by electrical network, then preparatory stage will consist in the power supply. The average power consumption of such modules is within 3.2 kW. This means that an ordinary but good outlet will be enough for connection. If the socket was not installed in advance, then you can purchase an invoice option, since it will be easier to mount and not needed additional tool in the form of a punch or drill with a crown. The cable for such an outlet must go directly from the distribution board.

This step is being taken in order to provide such a powerful device with a separate circuit breaker who would control his work. The rated current for which the machine must be calculated is 16 amperes. The best solution will install a differential automaton that is able to catch the slightest leaks. The socket is mounted slightly below the table top. This is done not for greater convenience of connection, but so that moisture and fats do not get on it during cooking. The socket must be grounded in case of a short circuit.

Note! It should be noted that standard socket withstands a load of 3.5 kW and a current of 16 amperes.

Step-by-step instruction

An important step during the installation of the hob in the worktop is the marking. Usually, the manufacturer in the technical documentation that comes with the hob indicates what should be the dimensions of the hole for installation. One of the options would be to make a sample from cardboard, which can be used to draw the outline of the future hole. There is another option, how you can make the markup, it can be seen in the photo below.

Place the hob on a worktop but turn it upside down. She will be an example. It must be located in the place where the direct installation will be carried out. The photo clearly shows that it is important to make a small gap from the edge of the countertop to the hob. Usually it is about 5 cm. It is done so that the edge of the cooking surface is not damaged from constant interaction with it.

The next step, as shown in the photo, is to apply the markings. To do this, the hob is simply traced in a circle with a pencil. The lines must be accurate so that they do not have to be redrawn several times, since this will only confuse you later.

The photo shows that the hob has a small protrusion, thanks to which it is fixed in the hole. This protrusion has a certain dimension that must be taken into account. It is also important to mark it on the contour of the future hole, as shown in the photo below.

In this case, it is necessary to make a small gap. If the protrusion has a length of 15 mm, then the size of the hob must only move 10 mm away from the main line. A 5 mm gap is required for smooth installation of the hob into the prepared hole.

After making the markings for the hob, it is necessary to prepare the holes to make it easier to cut the required part. Holes are drilled with a drill or screwdriver at four corners. In this case, it is necessary to ensure that the drill does not damage the facade or other elements of the kitchen set. The diameter of the drill should be such that the file fits freely into the hole.

To continue the process of installing the hob, you will need a jigsaw. His file is inserted into the prepared hole and the cut is made. It is important to remember that you need to cut along the inner line, not along the outer line. If a mistake is made, then the surface will simply fall into the hole without fixing.

In the process of work, it is necessary to remove sawdust in a timely manner so that they do not overlap the cutting line, since you can easily get off it and damage the tabletop. During the cut, it is necessary to ensure that the file does not damage the walls of the cabinets or their surface. Before going through the last side, it is necessary to provide the tabletop with sufficient support so that the nail file does not bite, and also so that part of the tabletop does not fall on the leg.

Once the hole is complete, you can try on the hob to make sure it fits properly.

The process does not end there. The table top is most often made from chipboard. If moisture gets on it, then it swells and deforms. When cooking on the hob, such a scenario is inevitable, so it is important to protect the place that has lost the laminated layer. To do this, a special sealant is applied to it, which is used when installing the panels. It simultaneously acts as a fixing base for the entire structure. The layer must be sufficient to cover all moisture accessible areas.

An adhesive sealant is applied to the reverse side of the hob rim, which will additionally fix the product on the countertop. After that, the panel is inserted into its place and gently pressed down until the contact with the surface of the countertop is felt. The sealant that has come out must be removed immediately, since after drying it will be more difficult to do. It is important to check that the abutment is the same over the entire surface. If this is not done, the glass may shatter under the pressure from a heavy saucepan.

Advice! If the hob is glass, then it is important to be careful when applying pressure so that it does not burst.

The fixation does not end there. Special metal plates are supplied with the surface, as seen in the photo above. They must be screwed in such a way that they provide support and prevent the panel from lifting above the table top. You can watch a video about installing the hob below.

Network connection

After completing the installation process, you can proceed to connecting the electrical part. Most often, hobs are supplied in a single-phase version, but they can also be three-phase, which will be useful if three phases come to a house or apartment. Usually the hob has a built-in power cable. But if it is not there, then you will need to buy it separately. To connect, you need a wire marked PVA 3 × 4. Each core of this cable is rated for a rated continuous load of 8 kW.

This is necessary for a small margin, which will exclude overheating of the conductor. The wires are stripped from both sides. With one, a plug is mounted, which in terms of current must correspond to that indicated for the hob. If this is not observed, then it may simply melt. The wire is not monolithic, so you will need to crimp the cores with ferrules. Near the terminal block, where the connection to the hob will be carried out, markings are usually applied.

The Latin letter L denotes the cable through which the phase comes, the letter N denotes zero, there may be a third letter E, which denotes the place where the ground wire is connected. Most often, instead of the third letter, a drawing is applied, which indicates grounding. It is important to firmly fix each core that is crimped with a ferrule with a bolt. The service life will depend on the quality of the contact. If under hob the oven will be installed, then a separate outlet must be provided for it. The total power consumption of the surface and the cabinet is twice that of a single-phase outlet.

Summary

As you can see, the installation of the surface can be done independently without significant skills. During work, all safety precautions and safety measures must be observed. When drilling and working with an electric jigsaw, you must have protective glasses in front of your eyes, which will protect you from flying sawdust. During the installation of the socket and connection of the electrical part, it is necessary to use tools that have dielectric handles that protect against breakdown electric shock... Before starting work, it is necessary to de-energize the machine, which is attached to the prepared wire in the kitchen.

I still chose an induction hob. Because I don't have gas in my house, and I didn't want a regular electric one. The panel from the manufacturer HANSA, there will definitely be an article about it, but today is not about that. Today I need to install this hob in my countertop! And I have never done this before, I just saw how the masters do it. But I didn’t really want to give 2000 - 2500 rubles, I didn’t really want to install the surface, so I decided to install it myself, in principle I did it, I think you can do it too ...

The article will be with pictures, so read and see everything step by step.

Guys for a start -. Be sure to read the article so as not to redo the wiring several times later!

1) Tool. To install (cut-in) the hob, we need a jigsaw, drill, tape measure, marking pencils and a flat board, about 1 meter (I have left of the furniture) or a large ruler.

2) Determine the place where we will embed the panel, I have this place above the void for the oven. Of course, the panel can also be embedded over cabinets with dishes and kitchen utensils, but as I think this is not very correct.

3) Try on the panel by eye. The main thing is that there is enough space around the edges.

4) Now the most difficult thing is to mark the dimensions on the countertop. To begin with, I determined the center, just measured the distance (where the installation will be made) and marked the center.

5) Now we take a book, it has everything required dimensions, you need to try to comply with them. First, I define the horizontal gaps. That is, what size should be set aside from the wall and what should be left to the edge of the countertop. Moreover, these dimensions are already indicated by the manufacturer, here they are in the picture - X and X1. X - 50 mm (up to the wall), X1 - 60 mm (up to the edge). We postpone these dimensions. I have a corner attached, it is 30 mm, so I set aside another 20 mm and that 50 mm from it. At the end, exactly 60 mm remains, you don't even need to measure there.

6) Now the dimension "A" is important for us - this is the width of the slab, we have it 560 mm, that is, 280 mm from the center (which we set aside). Draw two parallel lines from the center at a distance of 280 mm. And in the end, we get all sizes. Take a look.

7) Now we take a drill, insert a drill 8 - 10 mm (to fit the jigsaw file) and drill. We need to drill three to four holes (three are possible, then the last corner in which we do not drill - we will cut to it). Here are my three holes.

8) Next, we take a jigsaw and begin to cut the tabletop, everything is strictly in size. It should be noted the dimensions that are in the instructions already with gaps. We'll have to sweat the worktop is difficult to saw, but after 20 - 25 minutes everything was ready.

9) After that, we simply take out the cut plate and remove it.

10) We remove the sawdust and try to insert the panel into place, everything should be fine! They did it according to the manufacturer's size. The stove moves a little, that is, you can move it slightly to the right - to the left, as well as up and down.

Hob installation: basic rules and recommendations

The joy of purchasing a hob is understandable - now a new beautiful and smart assistant will appear in your kitchen. However, in order for her to fully show her talents, you need to know how to install the hob correctly.

How to install the hob: general requirements

This technique is available in electric or gas format. This is reflected in the difference in panel mounting, but general rules before the process itself remain the same:

1. Mandatory presence ventilation system. Modern rules hygiene and safety requirements dictate that there should be a hood over any hob. If this cannot be done, then be sure to install a high-power fan on the window.
2. The source material for the countertop can be any - the main thing is that its heat resistance does not go below the 100 ° C mark. This imposes certain obligations on the thickness, which should be within 25 mm (not thinner).
3. In the event that the installation is done between two cabinets, then you need to leave a distance from the wall of each to the plate at least 15 cm. kitchen wall the requirements are slightly reduced, but you still should not step over the 5 cm threshold. If this rule cannot be observed, then it is imperative to lay a heat-insulating material between the wall and the panel.

Installing the hob in a worktop: process features

The surface of the tabletop will have to be sawed - a jigsaw is best for this. From the materials you should prepare:

• special sealant;
• self-tapping screws;
• clamps.

After compliance general requirements you can start the work itself. It will consist of observing the following simple algorithm:

1. The instructions usually indicate the dimensions of the panel. If it is not there, then you can measure it yourself, but you do not need to do it tightly - you need to leave a gap of 1-2 mm between the panel and the tabletop.
2. Better to attach and circle the cardboard layout first.
3. The space between the hob and the edge of the worktop must be at least 5 cm.
4. Drill the corners of the tabletop with an electric drill.
5. Saw carefully along the marked lines from one sawn corner to another.
6. Close the edges of the tabletop in the places where it has been cut with a special seal (included with the purchase). It is also recommended to use a silicone sealant to protect the countertop from the negative effects of excessive moisture.
7. Lower the hob into the resulting niche.
8. Align it, but do not allow too much effort.
9. Firmly fix the surface using special clamps, securing them with self-tapping screws - this will hold the panel in one place.

Further actions in the event will depend on what method of connection this technique has.

How to install an electric hob

Installing a socket for the hob

An initial grounding check is of great importance in connecting such a plate. Second important rule is a ban on the use of adapters and extension cords.

Has its own characteristics and installation of the socket for the hob. You need to take care of its location before starting work, so that this moment does not distract. It is best to place it below the level of the table top.

Very often, in this process, a kitchen set is dismantled - this is necessary to prepare a new wiring channel, strengthen it and close it with a cement or putty layer. Only after that in back wall a hole is cut into the furniture, with the help of which the panel will be connected to the outlet.

Following actions

They must go according to the following instructions:

1. The electrical cord with grounding is connected to the connectors of the plate.
2. The panel itself is connected to communications. Modification of the power supply system is possible.
3. Functionality check in progress.

If you connect to single-phase network, then the work is supplemented by the following points:

1. A separate electrical line is being laid (it is better to take a three-core 3x4 wire).
2. A special socket with grounding is installed.
3. A circuit breaker is installed.

Modification of the power supply system is also very important - this significantly reduces both the breakdown of the device itself and the risk of electric shock to the user. To carry it out, you should contact a specialist.

A similar installation can be seen more clearly in the following video:

Installing the gas hob

Due to the specificity of connecting such equipment, only an employee of the gas service should connect it - poor-quality work by amateurs can lead to tragedy. The recommendations below are for them (and for those who have repeatedly connected devices to the gas main).

Connection features

There is a difference between recipient nozzles for main or bottled gas. This should be taken into account when connecting. You can unscrew them with keys 6.7 and 8. Those that go for main gas have a larger hole diameter.

The panel is connected to a gas source with a special flexible hose. For additional safety, in combined panels, it is worth installing a thermal shut-off valve - it will shut off the gas supply if the temperature goes over the threshold of 80 degrees (a second such valve will need to be installed on the gas cylinder).

After connection, all joints are checked for tightness. Usually, a soap solution is used for this - bubbles will appear on it if something turns out to be leaky somewhere.

It is best to turn off the gas valve after each use, so it should be controlled and easily accessible.

Installing the hob in a worktop: 6 steps

You can install the hob yourself if you first read the instructions Many years ago kitchen sets did not imagine the possibility of installing a hob in them. Today it is a common phenomenon, which saves space in the kitchen, as well as makes cooking more convenient and comfortable. You can install the hob in the worktop yourself. The main thing is to correctly determine the sequence of actions and follow it. It is very important to correctly determine the dimensions of the future opening.

Do-it-yourself hob installation

Modern technologies do not stand still. Today it has become possible to integrate hobs into kitchen sets, which has a qualitative effect on the interior of the kitchen and its functionality. The hob insertion will not notice a lot of time.

You can read more about the features of electric hobs in the article "Hob of 3 types".

First of all, you need to make markings on the countertop that will correspond to the dimensions of the hob.

Next to each side of the niche, you need to drill a hole, the diameter of each should be from 8 to 10 mm. The next step is to carve out the niche and internal processing silicone. The table top is installed on the lower level of the headset. The inside of the panel is attached with double-sided tape or a little plasticine. The table top is covered with silicone.

In order to properly install the hob, follow the step-by-step instructions

Step by step installation:

1. The table top is laid on lower part headset. If the walls are uneven, the countertop will need to be trimmed. And if they pass through it gas pipes, special holes must be made for them. The countertop should be ready to be installed down the kitchen.
2. Inside the box in which the hob will be installed, it is necessary to make a markup. To do this, you can simply make pencil sketches that will help you make further markup.
3. The worktop is laid face down, and on back side make markup for future inset.
4. In each intended cut, small holes need to be made so that you can work with a jigsaw.
5. Carefully cut out a niche using an electric jigsaw.
6. Care must be taken to ensure that the table top does not deflect under its own weight. It is better to maintain it carefully during the cutting process.

The inside of the cut is treated with silicone. After installing the panel, you can additionally coat it with silicone with outside... This is done in order to create an additional hydro barrier, since the fasteners may not be enough to press against the tabletop.

The gas hob must be chosen very responsibly, because it should last for many years. After the choice has been made, the panel must be installed so that it is convenient and safe to use. You can embed the panel yourself, but you should not do this if you are not confident in your abilities. In any case, you can turn to a specialist for help.

At self-installation it is important to prepare everything necessary materials: panel, measuring instruments, pencils, sealant, adjustable wrench, saw, gas winding, steel hose.

All work related to gas is unsafe to carry out. It is best to perform the installation with a technician or someone who knows the entire installation process thoroughly. One of the most important milestones installation - hose selection.

If you need to install a gas hob, then it is better to seek the help of specialists.

Hose Selection Tips:

• Check the hose for damage. There should be no defects on the hose.
• The hose must be certified. When buying, you should ask the seller to provide all documents for the goods.
• The hose can be corrugated metal or rubber.

When installing the panel, the calculation of the dimensions must be given Special attention... Sometimes, in the kit for the hob, you can find a template that you need to use in order to properly saw the worktop. It is important to remember that water must not get on the surface of the panel. Gas countertop must be located at a safe distance from furniture and textiles.

How to properly install the hob in the worktop

Built-in electric stove - very convenient device for installation in the kitchen. It works as efficiently as a stationary cooker, but does not take up as much space. Installing such a panel can be quick and easy without the need for specialist assistance. The surface can be combined with an oven for even more convenient cooking.

If the master conducts DIY repair not the first time, then installing the hob will not cause difficulties.

Before installing the panel, you need to properly cut a hole in the countertop. To facilitate the installation work, manufacturers indicate the required dimensions in the instructions for the device. Pre-marking greatly simplifies and speeds up the installation process.

Before installing the hob, it is necessary to make special markings on the worktop.

Installation steps:

• On the countertop, you need to make a markup that will match the dimensions of the panel.
• Using an electric jigsaw, you need to make a cutout in the countertop. To get started, you need to drill a small hole for the jigsaw. The cut will be even if you use a fine-toothed jigsaw file.
• Dimensions (edit) hob must line up with the cut-out hole. Sections must be treated with a sealant or nitro varnish. For processing, self-adhesive sealing tape can be used.

The electric tabletop is connected, focusing on the diagram. It can be found on the back of the panel. It is important to connect the wires correctly in order to be able to regulate the switching on of the burners and their temperature.

What to look for: Attaching the hob to the worktop

The hob installation process is simple, but requires careful preliminary preparation... The first step is to choose the right hob, check its passport data, prepare the tools and decide on the installation site. The installation of a cooking gas and an electric surface is practically the same.

You need to fix the panel on the table top, in which you need to make a corresponding cutout.

It should be noted that to install electrical panel you will also need installation electrical outlet... For the gas panel, you need to take care of the gas communication. The built-in panel must be installed so that the maximum gap between it and the worktop is 1-2 mm.

When installing the hob, special attention will need to be paid to its attachment to the worktop.

What to look for:

• Correctly measure the dimensions of the panel and transfer them to the cutout in the worktop.
• Cut out the necessary segment in the worktop in order to carry out the installation correctly.
• Treat the countertop with special materials that will protect it from the effects of external negative factors.
• Flush the panel into the cutout.

It is important to remember that the flush panel must not be forced into the gap. If there is a backlash, the location of the table top must be aligned, focusing on the front edge. Fastening the seal over the entire surface of the countertop will avoid contamination of the panel.

Hob gasket

It is imperative to attach to the hob gasket... If the panel is removed after some time of use, you will notice that the seal will be covered in dirt and grease. The gasket needs to be replaced from time to time.

If there is a gap between the panel and the countertop, then the plate can be fixed in the plane, but this must be done so that debris does not fall into the vertical gap.

You can buy a special tape, or you can use a glass seal. The table and cutout can be pre-treated with a clear sealant. Remains of sealant must be wiped off or carefully removed with a spatula.

Many people prefer to use sealing tape because it is safe and environmentally friendly.

Advantages of the sealing tape:

• Reliability;
• Ease of use;
• Environmental friendliness.

His high quality Bosch seals are known. Just putting the panel on isn't enough. It must be protected from moisture, grease and debris. If the panel is installed in a large opening, and a gap is formed, then tape and sealing the gaps with a sealant will help to save the situation.

Installing the hob in a worktop (video)

The built-in hob is a convenient device that saves space in the kitchen and ensures comfortable cooking. The rules for installing the panel are simple, so you can install it yourself. It is possible to cut the panel qualitatively only when the dimensions of the panel are measured correctly. After cutting a hole in the countertop, it must be well sealed to protect the panel from water and dirt. All actions must be phased and coordinated.

Similar materials