How to adjust a reinforced-plastic entrance door. Instructions for simple customization of plastic doors

Before installing a plastic door, you must not only choose the manufacturer carefully, but also pay attention to its components. Only in these cases will the door serve you for more than a dozen years. But some time after installation, the door mechanisms may fail. To eliminate this malfunction, it is not at all necessary to contact the masters. You can adjust the mechanisms yourself. To do this, you need to know how to adjust it yourself.

The most common causes of breakdowns

As a rule, all faults plastic doors arise as a result of a violation of the position of the canvas itself. Due to its frequent use, all movable mechanisms gradually fail. Therefore, before adjusting the plastic door, let's first figure out in what cases it is necessary to do this.

• The bottom of the door is rubbing against the threshold. As a rule, this is due to insufficiently tightly clamped mechanisms. This is not due to the quality of the door itself, but to the carelessness of the master who installed it. In addition, the door leaf can sag under its own weight. This is mainly due to the weighted
• The middle part of the door (near the handle) rubs against the plastic strip. This usually occurs as a result of sudden changes in temperature.
• The door does not close hermetically. The cause of such a malfunction can be not only the same sharp temperature changes, but also the displacement of the pressure roller after a long use of the doors.

Prevention of malfunctions in plastic doors

Many people probably think that, knowing how to adjust a plastic door, it is not at all necessary to treat it with care. Unfortunately, this is not the case. The door can be adjusted several times. But after a while the moment will come when this procedure simply will no longer help. Thus, it should always be remembered that door prevention should be taken seriously as well as its selection or installation.

So, before you buy this or that door model, never refuse to complete it, even if it will increase the cost of your purchase. Otherwise, before you adjust the hinges of plastic doors yourself, you will again need to spend time and money to find this or that component.

Necessary accessories for plastic doors

Most important tools for adjusting plastic doors, it is customary to consider the following:

1. Microlift. This device will help to eliminate the malfunction of doors of any size and weight. It helps prevent sagging of even the heaviest door leaves. The microlift takes on part of the door's load, but only in its closed position. It can look different. The most common types are a roller at the bottom or a movable plate at the top of the web.
2. Door opening limiter. This mechanism not only helps to prevent the door from sagging, but also sets the maximum angle of its opening in such a way that it protects the door leaf from hitting the slopes.

In addition, before you stop at choosing one or another manufacturer of plastic doors, find out more information about it. The fact is that many companies neglect the quality of the fittings themselves, install cheaper ones, which may also be one of the reasons for the minimum service life of the product.

Eliminate sagging door leaf

We have already found out what the sagging of the canvas depends on, now let's look at how to properly adjust the plastic door with our own hands in this situation.

If you notice that the canvas clings to the threshold, you need to eliminate this malfunction as soon as possible. To do this, open the doors and find a small screw on the top hinge. As a rule, it is a hexagon. In some cases, it may look like an asterisk. In one case or another, you will need to choose a wrench for the screw.

So turn the screw clockwise. Make two or three turns. Close the door. It should now close freely.

If the canvas sags very much, and these actions did not help to eliminate this malfunction, then experts give the following recommendation on how to adjust the height of the plastic door. Locate the adjusting screw under the protective cap of the lower canopy and turn it clockwise a couple of times. These steps will help you fix the door sagging problem.

Elimination of mashing of the door leaf from the side

Side rubbing of the door is also easy to prevent. How to adjust the plastic door in this case? To do this, find on the lower canopy now another screw, which is located not below, but on the side, that is, with inside canvases. Again, by turning it clockwise, you can put the door leaf in the right place. It will no longer cling to the jamb and can be closed easily.

If this technique did not help to eliminate the door mashing from the side, find the upper canopy, about which it was written above, and follow all the same steps.

Establishing door tightness

If you notice that your door is not closing tightly, then this troubleshooting step is for you. Let's see how to adjust the pressure of the plastic door.

First, turn the stripping to the ends of the door. There are special eccentrics. By rotating them you can adjust correct mode doors. The only tricky part here is finding the right eccentrics. Usually, at the top, side and bottom, they are installed in three. All of them should be gradually turned at the same angle so that the door closes tightly. But since this fit will be only near the handle, it will also be necessary to adjust the awnings with special screws.

Door handle adjustment

We have already covered how to adjust the plastic door. But what if its handle does not function properly when opened? Do not worry, you can also fix such handle problems with your own hands.

To do this, move the decorative plate 90 degrees. Underneath you will find a handle mechanism and mounting screws. Fasten these screws, and the handle on the door leaf will be fixed stronger. Thus, you will be able to adjust its fixing density yourself, which makes it possible to troubleshoot the door opening mechanism.

Replacing the handle in plastic doors

Now you know how to adjust a plastic door with your own hands. But more difficulties will be caused by replacing her handle. After all, such fittings are the most vulnerable. It is also worth noting that its service life is much shorter than indicated by the manufacturer.

The main reason for the breakage of the handle of plastic doors is the poor quality of the material. Its constant use leads to cracks, and in the future - to the fact that the handle completely breaks off.

If you are faced with the latter problem, first you need to choose an analogue of your pen. You need to choose this or that accessories carefully, turning Special attention for the identity of the dimensions of the part itself and the fasteners. As a rule, all these devices are almost the same, but in this case it will be useful to play it safe.

The handle is attached directly to the metal hidden under plastic profile the base with self-tapping screws, which are subsequently closed with decorative plugs.

We hope our advice helped. Now you know how to adjust a plastic entrance door yourself.

Often, when installing PVC balcony doors, technical problems arise associated with the operation of opening mechanisms and other structural elements. This is due to many factors: violation of installation technology, building shrinkage, improper door operation. To eliminate minor malfunctions, you can do it yourself - it is enough to correctly adjust the plastic door, following the step-by-step instructions.

Common causes of PVC door malfunctions

Adjustment of plastic doors is carried out immediately upon detection of visual structural defects in the following situations:

Violation of the tightness of the door structure

The fault can be recognized in this way. Open the door, and insert a piece of paper into the space between the frame and the canvas. Then close the canvas and try to pull the sheet towards you. The paper is pulled out effortlessly if the closing mechanism is not pressed properly. Similar actions are performed along the entire perimeter of the structure. Violation of the door tightness leads to the appearance of condensation on the glass surfaces.

Sagging and skewing of the door

It is quite simple to determine the subsidence of the canvas - a closed sash is traced with a pencil. If in open position the reference line runs parallel to the frame, this indicates that there is no distortion. In some cases, the sagging of the door can be determined by the formation of a through corner slot at the top of the structure or the friction of the lower part of the door leaf on the threshold.

Door frame rubbing

Difficulties in opening and closing the canvas appear as a result of friction against the box. This is due to the wear of the upper protective layer of the door, which can lead to damage to the metal-plastic profile and incorrect operation of the fittings.

Looseness or tight turning of the handle

The door handle can become loose due to insufficient fixation in the seat. This can be caused by improper or careless use of the fittings.

Another problem is tight turning of the handle, which occurs as a result of damage or contamination of the key core or the handle itself.

Incorrect operation of the locking mechanism

This is due to dirt, wear or damage to the mechanism.

Such malfunctions indicate that the PVC door to the balcony is in a bad technical condition and requires immediate adjustment.

Plastic door customization process

Adjustment of plastic doors provides for the identification and elimination of all existing faults. Perhaps fittings or individual elements structures are badly worn out, so the problem can only be solved by completely replacing them.

Consider the most likely breakdowns of the entrance balcony euro-door, which you can fix yourself.

Working tools for customization

Depending on the size of the regulating and fixing elements of the structure, as well as the manufacturer's company, the following working tools will be required to adjust the locking mechanisms:

• a set of hexagons of various diameters;
• a set of star keys;
• flat and Phillips screwdrivers;
• pliers;
• plastic overlays;
• means for lubricating sealing strips;
• clean rags.

Adjusting door hinges and awnings

Metal-plastic doors are completed hidden hinges overhead type, the number of which depends on the functional and technical features models. The hinges are adjusted horizontally and vertically.

You can adjust the hinges horizontally as follows:

1. Open the door leaf and unscrew the screws from the hinges located at the top. To loosen the screws, you can use a hex key of a suitable diameter.
2. Then close the door, remove the decorative strips, which are designed to hide the adjusting screws.
3. To prevent possible skewing of the blade, the elongated screw at the top must be tightened more than at the bottom.
4. To move the fabric evenly towards the hinges or reverse side, it is necessary to remove the lower decorative strip, tighten the loop and loosen the screws located horizontally.

Vertical adjustment of the hinges is carried out to raise or lower the door. To do this, you need to find an adjusting screw, which is located at the end of the hinge from the bottom along the axis. In some models of products, such an element can be hidden under a decorative strip.

To adjust the door leaf vertically, a 5 mm hexagon is used. Making a rotational movement with a wrench clockwise, slightly raise the blade and set it in the desired position. Then tighten the screw in the opposite direction and install the decorative strip.

Adjusting the door handle

Often, the problem with the handle for a plastic door is associated with its loosening in the seat and tight turn when opening / closing the leaf.

Adjustment of the handle when it is loosening is carried out as follows:

1. The plastic cap at the base of the handle can be rotated 90 degrees.
2. The hidden screws are tightened with a Phillips screwdriver so as not to damage the handle body.
3. The hardware is checked for functionality.

Stiff handle movement may be associated with skew. door leaf or breakdown of the locking mechanism. After troubleshooting the position of the door, the locking mechanism will work properly, otherwise it will need to be replaced.

The faulty handle can also be replaced if necessary. To do this, it is installed in the "open" position, the screws are unscrewed from the seats, the entire lock is dismantled. The new handle fits into the seat and is secured with screws.

Replacing the sealing tape

If the door structure is used for a long time with sagging or skewing, this can lead to deformation or damage to the sealing strip.

A high-quality sealant has been in operation for 5-7 years, but as a result mechanical damage or door malfunctions, its wear can occur much earlier.

To replace the sealing tape for a plastic door, you will need: scissors, a new tape, silicone glue. The sequence of actions is as follows:

1. Careful dismantling of the old seal with improvised means and purchasing a new product. It is better to choose a sealing tape from one manufacturer to ensure maximum sealing of the structure.
2. After dismantling, the grooves are thoroughly cleaned to remove adhesive residues and dirt.
3. To avoid displacement of the seal, a thin layer of silicone adhesive is applied to the corners.
4. The prepared sealant is evenly placed in the cleaned groove, starting from the place of fixation of the old tape. In this case, sagging, tensions or material assemblies should be excluded.
5. The joints are fixed close, sometimes a cut at 45 degrees is made.
6. A properly installed seal must completely prevent cold penetration from the balcony.

Leveling and pulling up in height

To tighten the door structure in height and eliminate its friction against the threshold, it is necessary to tighten the vertical adjustment screw.

The sequence of actions is as follows:

1. For the adjusting screw, use a hexagon or a wrench with an asterisk attachment. Decorative overlays are dismantled from the hinges.
2. The door leaf opens to gain access to the adjusting elements.
3. The upper screw in the hinge is tightened clockwise with a hexagon, observing a strictly vertical position of the sash.
4. With a significant shift, the lower screw is adjusted. It is important to remember that in order to raise the door, the screws are tightened clockwise, in order to lower - against it.

Align the plastic door horizontally so that it stops looping, you can use the adjustment screws that are hidden under the technological holes in the hinges. To provide free access to them, the door leaf must be kept open.

When the door is moved to the right side, the adjusting element is tightened counterclockwise, when it is moved to the left, it is tightened clockwise. Thus, it is possible to adjust the position of the door in the horizontal plane in the range from 2 to 4 mm.

In some cases, the door is adjusted as follows: at the end of the open door leaf a special tongue is pressed to transfer the structure to micro-ventilation mode. This allows easy access to the adjustment screws on the top hinge. After adjustment, the door leaf returns to its original position.

Other door problems

If the door had time to seriously sink and other troubleshooting methods did not give the desired result, then it is necessary to carry out a small repair using a double-glazed window:

1. The glazing beads holding the glass unit are dismantled.
2. With a special plastic or wood spatula, the glass unit is shifted to the side to eliminate the sagging of the door leaf.
3. Plastic spacers are installed in the formed gap.
4. Next, the location of the door is checked and the glazing beads are installed.

In some cases, a malfunction of a plastic door is associated with a broken lock. In case of failure a separate part mechanism, it is enough to replace it with a new element purchased in a specialized point of sale... If the entire lock breaks down, a complete replacement of the device will be required.

Prevention of malfunctions of plastic doors

To avoid costly repair of PVC doors, it is necessary to provide timely Maintenance fittings and structural locking mechanisms.

High-quality door hardware from European manufacturers is capable of withstanding maximum loads of up to 130 kg, while the tensile strength of products of Chinese brands does not exceed 90 kg.

To ensure the smooth operation of plastic doors, two elements allow - an opening limiter and a microlift, which are not included in the standard package of the product. Therefore, it is recommended to purchase them separately before installation. door structure.

Stopper is a special comb, which is designed to limit the opening of the door leaf. This prevents possible sagging or skewing of the web.

Microlift is a device in the form of a movable plate or roller, which is provided for overall and volumetric plastic doors equipped with a heavy glass unit. The microlift eliminates the sagging of the door leaf when it is closed, taking on part of the weight of the door.

Anyone should be able to solve problems with the elimination of minor malfunctions of a plastic door House master... Similar designs are used for balconies, loggias, winter greenhouses and summer kitchens. Self-adjustment will allow you to correctly set the operating modes "winter" and "summer", save cash for maintenance and repair of the door.

Installation metal-plastic doors and window systems to the balcony is a frequently practiced scheme. It is convenient, has a reasonable cost and is durable, both in operation and in external data. After a certain period of time, the door leaf opening mechanisms begin to work worse. This period depends on the accuracy of use, the manufacturer of the mechanism, the correct initial installation, and even on temperature parameters. If the balcony door begins to open or close poorly, this does not mean that it is time to change the entire unit - it is enough just to adjust the mechanism. How to adjust a plastic balcony door? It is enough to know a few basic points.

When do you need to adjust the door?

It is worth thinking about adjusting the balcony door only when malfunctions in the operation of the sash become noticeable - discomfort when using the door.

Remember when new windows and doors were just installed on the balcony. The handle turned easily and into a strictly necessary position, the door did not "get confused" - to make a full opening or set for ventilation. All movements of the sash were smooth and light.

Any problems with operation balcony door, even in the form of a more rigid opening or closing - adjustment of the mechanism is necessary.

Frequent problems and why they occur

Plastic balcony doors have been widely used as balcony doors for more than a year. During this period, companies that perform technical and warranty maintenance of window and door mechanisms were able to easily compile a list of the most common problems that need to be adjusted to the balcony door.

Sagging under its own weight - the door leaf begins to cling to the threshold. At first, almost imperceptibly, over time - more and more clearly.

The sagging of the balcony door is caused by the natural sagging mechanism of the hinges. The weight of such a sash is rather big and over the years the hinges get tired of holding it. The rate at which this problem occurs depends on the manufacturer and material of the hinges, as well as on the number of chambers and the thickness of the glass.

If you live in a climate with a sharp change in temperature and humidity, and your balcony is not reinforced with additional thermal insulation materials, get ready for the door to start sticking in the middle. This is how the door leaf is displaced to the side, towards the frame.

In 90% of cases, it occurs as a reaction to climatic conditions - temperature drops, high humidity followed by drought.

Next frequent problem - the balcony door ceases to adhere tightly to the frame when closed. This malfunction not only causes inconvenience during use, but also hazardous to the health of the residents of the apartment. Unplanned in the middle of winter is a very unpleasant experience.

The cause of this problem is age - the age of the mechanism. Over time, the parts responsible for pressing the door leaf to the frame weaken and need to be adjusted.

Substandard materials and rough handling will lead to doorhandle loose or fall off altogether. This problem is also not difficult to fix.

Other possible malfunctions in the mechanisms occur much less frequently, some require the intervention of specialists.

Instructions for adjusting plastic doors

The problems described above can be fixed by yourself, with some knowledge and general idea about the work of the door mechanism. It won't take long to fix these problems - normal adjustments rarely takes more than 30 minutes. Observing due care, it is impossible to irreversibly spoil something when adjusting the mechanism.

Sagging

To eliminate the sagging of the balcony sash, the task is to raise the sash to a certain height.

• To do this, remove the decorative and protective cover from the lower hinge.
• There is a vertical hole in the top of the hinge into which you need to insert a hexagon ( standard size – 6 mm).
• Rotate clockwise with the hex wrench until the door snaps into place.
• Check the opening of the sash after each round - rarely more is needed 5 turns.
• If problems arise or the hexagon does not rotate, it is necessary to slightly adjust the upper hinge in the same way.
• Make sure that the sash does not cling to the threshold, but does not rise too high, otherwise the tightness in the closed position will be broken.

Video

Sticking in the middle

When the sash sags, we resort to vertical adjustment, and in case of seizure in the middle caused by climatic conditions - to horizontal adjustment.

1. Open the sash wide.
2. At the end, near the inner part of the hinges, there is a hole.
3. If the elements of the mechanism are closed with plugs, remove them.
4. Insert a hexagon into the hole near the bottom hinge.
5. Begin clockwise rotation similar to vertical adjustment.
6. This will pull the door to the hinge.
7. Check after each revolution.
8. If the malfunction persists and the sash is still jammed, do the same with the upper hinge.
9. After success, replace the plugs.

Loose fit

There are locking mechanisms in the end part of the balcony sash. It is they who will help save the residents of the apartment from unwanted drafts and keep the house warm.

Most plastic flaps have 4 locking mechanisms... They have two types of eccentrics.

To change the fit of the door, it is necessary to act on these eccentrics. Diagonal position for standard and center position for i.s. indicate an average degree of sash clamping.

Displacement towards the vertical or to the right - weakens the degree of pressing the sash to the frame, displacement towards the horizontal or to the left - enhances.

For the cold season, it is better to install tighter fit of the sash.

Now you know how to fix common problems with door mechanisms. There is nothing difficult in this, but the presence of a hexagon will play into the hands. If not, you can try using a screwdriver.

If you are afraid of introducing a balcony sash into the mechanism, invite a master who will not only make a competent adjustment necessary elements, and will teach you how to adjust the position of the sash in the future yourself.

This problem is one of the most common and brings significant discomfort.

Loose knobs are quickly fixed. Of the tools, you only need a Phillips screwdriver.

Between the handle and the sash panel there is a vertical plastic cover - a plug. It needs to be turned to a horizontal position, you will see two screws. Turn the screwdriver clockwise to tighten the screws.

They should be twisted tightly, but no frills.

Check - the handle should start working normally without dangling. Return the plug to its original position.

If the malfunction persists, there is a high probability that an almost imperceptible crack has gone into the plastic of the handle. This is the reason for purchasing a new handle for the balcony door.

If the doorknob isn't loose, but feels tight or doesn't work well, try lubricating door mechanisms grease type WD.

With the correct adjustment, the door to the balcony will serve for many more years.

The door serves to delimit space in an apartment or in a house, protects residents from street noise and winter cold. Many people install plastic structures in their apartments: they look good and have many other advantages. But they also have a drawback - the large weight of the shutters. It leads to sagging and loss of tightness. For troubleshooting, there is an instruction for adjusting plastic doors yourself.

Problems most often arise with the onset of autumn. The plastic sheet begins to close poorly, touch the frame, and require additional efforts when turning the handle. As a result, cold penetration may occur. street air into the room. To eliminate these problems, the plastic doors are adjusted, which can be done on our own.

If the plastic product is under warranty service, then it is better to call the master. He can check the entire door structure and establish the cause of the problems. After that, he will carry out work on the lubrication of the parts and the necessary adjustment of the plastic door.

The adjustment can consist in adjusting the plastic product horizontally and vertically, as well as adjusting the pressing of the web against the box. The door will acquire the qualities of just assembled structure: it will be tightly pressed against the box, will not be randomly closed or opened.

Prophylaxis

Engage in adjustment PVC doors will have to be annually. To do this less often, you need to do some simple rules prevention. It is good to equip the sash with an opening limiter and a microlift. The microlift will protect the canvas from sagging, and the stopper will not allow the hinges to loosen when the doors are fully opened.

To prevent the handle from breaking, do not hang heavy bags on it. Plastic parts stay intact longer if wiped with a clean, damp cloth. Any plastic door structure includes rubber seals... They must be regularly lubricated with silicone compounds that give the rubber plasticity.

The lock, eccentrics and other parts of the mechanism are also subject to lubrication. Over time, the handle turns tighter, you have to lean on it with all your body weight. From this, distortions of the canvas appear. If you follow all the rules, it will last much longer. Metal fittings are lubricated with technical petroleum jelly.

How to adjust a plastic door

Adjustment of a plastic door begins with identifying defects. This can be done using a paper strip. They put it at open door onto the frame and close the sash tightly. After that, you need to pull the paper towards you. If it is pulled out without effort, it means that the door does not press well against the frame. In this way, it is checked around the entire perimeter. The adjustment pattern depends on where the paper is loose.

If the blade is displaced in the horizontal direction, you need to remove the plug from the hinges and tighten the self-tapping screws. After that, use a hex wrench to rotate the horizontally located adjusting screw. In this way, the horizontal displacement of the PVC door is adjusted.

Sagging of the canvas

The door often sags under its own weight. When the web is displaced in the vertical direction, it is simply returned to its place by rotating the adjusting screws that are located at the bottom of the hinges. To do this, use a hexagon. If the operations are performed correctly, the plastic flap will take the desired position and will be in contact with the box tightly.

If you move the door in height, it moves up to 2 mm. Turning the adjusting screw counterclockwise will lower the door leaf. Clockwise - rises. The main thing is not to rush. The desired result brings only correct adjustment door hinges.

Mashing

With a large degree of lowering vertically, the canvas begins to touch the elements door frame... The canvas is rubbed. The malfunction is regulated by retraction of the web to the right or left. It is recommended to start work from the bottom. To perform the operation, you need to take a hexagon and insert it into the corresponding hole. The PVC door will begin to slide towards or away from the hinge. In the same way, the upper part of the structure is taken to the right place.

We set up the clamp ourselves

Over time, a situation may arise that the PVC door does not open or opens, but with difficulty. In this case, frontal adjustment of the structure is used. There are two ways to adjust the pressure of the plastic door:

• using eccentrics;
• using the clamping mechanism.

Eccentrics are located along the perimeter of the end part of the door leaf. The clamping mechanism is located in the canopy area. To adjust the pressure using the eccentrics, you need to turn them around their axis. As a result, the pressure of the blade against the box will change. If the eccentric moves towards the room, the clamp will weaken. It is recommended to choose this position for summer season... For winter, you need to turn the eccentrics towards the street. All eccentrics turn in the same direction. This can be done with a special wrench or pliers.

Loose fit

It is a little more difficult to adjust the door with your own hands if it does not fit snugly. You can notice this problem by the sensation of turning the handle - more effort has to be made. The eccentrics in this case are already set to the winter position. You can put them in the middle position, which will weaken the clamp. If this does not help, the reason lies in the handle: its entire mechanism is clogged, and the canvas does not close well.

Handle adjustment instructions

Often there is a situation where the handle is loose. In this case, you need to adjust it. For this decorative strip rotates 90 degrees to loosen the mounting screws. These screws are unscrewed and the handle is removed. Then you should carefully inspect the parts, if necessary, replace those that are out of order. The assembly is carried out in reverse order... The assembled and lubricated handle serves well for a long time.

Adjusting plastic doors yourself is a simple matter. To perform all operations, it is necessary to open the sash to gain access to all mechanisms. The adjusting screw is tightened with a 4 mm Allen key.

Required tools

To carry out repair and adjustment work, some tools are required:

1. hex keys;
2. flat screwdriver;
3. Phillips screwdriver;
4. plastic gaskets;
5. roulette;
6. rubber seals (not always);
7. adjustment instructions.

This set of tools is enough to carry out quality work... It remains only to monitor the health of the structure:

• if necessary, the old seal is removed and a spare one is installed;
• you need to monitor the level of the canvas in the horizontal plane;
• the sides of the hinges must always be firmly fixed;
• timely adjust eccentrics;
• lubricate all assemblies and parts regularly.

These actions will extend the life of the PVC doors.

Before each user plastic products, after a long time of operation, a dilemma arises - how to adjust the plastic door? No matter how high the quality characteristics of the door and its components, which are designed to ensure the closing and opening of the PVC sash, after a certain time the mechanism, one way or another, will need to be adjusted.

If it is necessary to regulate PVC doors, it would be more rational to contact the appropriate specialists, in particular to those who carried out its installation. But, unfortunately, such an opportunity is not always available, nevertheless, and the departure of the master is unlikely to be carried out on the day of the call.

In addition, mastering the skill on your own is not at all difficult, since the process of adjusting a plastic door is not something supernatural. Moreover, customizing plastic products is never a frequent procedure. Adjusting a plastic door is only relevant when you have a complaint about the door's functioning.

The installation of a new plastic door also includes adjustment work, which is carried out immediately, and for a long time after, the design should not cause unnecessary questions. But after a time of active operation, the product will still need to adjust the mechanism, as a result of sagging, poor pressure or the inability to close the door.

Despite the excellent quality and confidence in the organization installing the door, it is recommended that you personally observe the adjustment process to make sure that the adjustment of the plastic doors was made correctly.

Upon completion of work related to the establishment of loops plastic construction, pay attention to the following points:

• the frame should fit snugly against the box around the perimeter;
• opening and closing the door should be easy, without additional effort, without squeaks;
• use building level to check the verticality of the door;
• check the arbitrary opening and closing of the sash. To do this, open the door halfway, while checking to exclude the effect of wind and draft.

Frequent damage to the plastic door

The most popular defects in the work of the product are as follows:

• The bottom edge of the sash touches a part of the frame that functions as a threshold. This occurs as a result of the sash sliding under the influence of its own weight;
• The canvas touches the middle of the frame. The reason for this is the direct shift of the sash under the influence of various deformations, as well as temperature;
• Poor clamping of the sash to the frame, as a result of wear of the seal;
• Doorknob staggering and falling out of slot.

Initially, it may seem that adjusting a plastic door is a complicated procedure based on the options possible malfunctions... But in fact, you just need to understand which mechanism needs to be configured, and the instructions below will help you troubleshoot problems with your own hands related to a plastic product.

Adjusting the plastic structure

Before you start setting up a PVC door with your own hands, stock up on screwdrivers (regular, flat and cross), hex keys different sizes, gaskets.

Competent instruction and necessary tools will allow you to correctly perform the entire cycle with your own hands, and as a result, the adjustment of plastic doors will be successfully and safely performed.

Elimination of sagging of the sash

To eliminate such a breakdown, you should direct the canvas up and slightly move it towards the loop, which is located above. Open the sash, and with a hexagon wrench (4 mm), unscrew the screw at the end of the sash at the top, at the location of the hinges.

To move the sash, make about 1-2 turns clockwise. Then close the sash and remove the protective cap from the hinges arranged at the bottom. Turn the upper hinge screw while slightly lifting the blade. If the sash moves easily, then the problem is solved.

Pressure regulation

Diagrams for setting hinges on a plastic door.

To adjust the pressure of the curtain to the frame, it is necessary to use a locking element. It is located inside the sash and acts as eccentrics. The trunnions are adjusted with a special key and pliers.

Do-it-yourself clamp setting is done in summer and winter seasons, this is sufficient for normal operation of the product. In winter, you should independently adjust a tighter and stronger pressure than in summer. It is necessary to press the sash to the frame from the hinge side by means of adjusting screws.

Horizontal adjustment

Correction of the work of the hinges of the plastic structure can be done both in vertical and horizontal directions. For horizontal adjustment, first remove the door from the hinges at the top.

Then close it and lift up the caps that hide the adjusting screws. To avoid skewing the product, tighten the long screw at the upper hinges slightly more forcefully than at the bottom. To ensure the same movement of the sash, remove the cover plate from the hinges and tighten it by loosening the screws horizontally located in the door hinges.

Vertical looping

If it is necessary to raise or lower the product, adjust the mechanism vertically. There is an adjusting screw along the axis of the lower hinge. To adjust the entrance plastic doors, a hex screwdriver (5 mm) is useful.

By turning the tool, the door can be raised slightly, and in the case of a screwdriver turning in the opposite direction, the structure will be lowered.

How to avoid frequent adjustments?

It will not be possible to completely get rid of the door adjustment, but it is quite possible to make it less frequent. When purchasing a double-glazed window, worry about the compliance of the fittings and the weight of the canvas.

The optimal sash weight is considered to be 100-130 kilograms.

The sagging of the structure under its own weight can be eliminated by installing an auxiliary piece of fittings, which is called a sag compensator, better known as a "microlift".

Such a detail is simply necessary for the product, especially in the presence of a double-glazed window unit with impressive dimensions of the structure. And if you correctly install the supporting tire - the opening limiter with your own hands, you can easily avoid jamming and sagging of the structure.

As you can see, adjusting a plastic door is not very difficult if you wish.