What is the best way to paint walls from imitation timber. How to paint imitation timber

tree for country house- most suitable material both for outdoor and inner lining. Pledge of cozy warm atmosphere and nice-looking facade and interiors. Minus the material - low resistance to aggressive factors external environment. In this article, we will tell you how to paint imitation timber in order to achieve high quality and maximum durability of the finish.

All paints and varnishes can be divided into two large groups:

glazing (emphasizing the woody structure);
covering (hiding the pattern of the tree).

The painted facade is not afraid of the harmful effects of the sun, precipitation, wind, temperature changes.

The internal sheathing board is processed more often in decorative purposes, with the exception of rooms with high humidity. For this, both traditional impregnations and primers are used, as well as alternative products: various oils and organic solutions. Read about how to properly paint the imitation of timber inside and outside the room, what paintwork materials to use in each case, what to use for finishing, Further.

How to paint an imitation of timber inside the house?

A fact that few people know about: the specific composition of the primer is selected for the “finishing” material! That is why manufacturers of different paints for simulating timber indoors recommend using a specific staining technology (antiseptic primer, intermediate layer, top coat), optimally suited for this particular composition.

We try to select our own coating for each material - thanks to our extensive experience, our specialists simply know when and what is best to use. For example, there is a special oil for decking - it differs from the compositions that are used for facade boards and for interior cladding.

Before painting inside the imitation of timber, boards:

polished;
are dedusted;
treated with antiseptics (compositions that prevent rotting and the formation of fungus).

Important! To get a high-quality result, the boards are first painted and only after complete drying are attached to the walls.

The paint is applied in 2-3 layers on the pre-primed sides and ends of the products, and each previous layer must dry completely before applying the next one. Works can be performed with a brush or a spray gun (spray gun).

How to paint an imitation of a bar on the outside?

For exterior finishes, special oils or varnishes can be used. Oils provide not only protection, but also toning - you can choose a composition that will give a very noble, “velvet” tone, or, conversely, light, delicate - how to paint an imitation of a bar outside the house, in general, a matter of taste.

Here is what, for example, you can create an exquisite wooden facade, if you treat it with dark tinted oil. By the way, coatings for facades necessarily contain pigments that protect the material from UV radiation - perfect option if not very resistant pine or rare tropical wood is used for sheathing.

The main stages of the work are identical: the boards need to be processed in the same way, primed and only then painted, the difference is only in the selection optimal material and the number of layers:

varnishes are more durable and have a wide color palette;
oils will have to be renewed every few years, but there is no need for laborious grinding. Fragmentary tinting of a damaged coating is also possible (after removing stains, repairing chips, etc.).

When deciding what is better to paint the imitation of a bar on the outside, remember the main thing - for outdoor work, they choose paintwork materials that are resistant to ultraviolet radiation and temperature extremes.

So, how painted imitation of timber is made, how to order painting of panels, and what is the cost of painting imitation of timber, we will tell you in this article.

Often, painting the imitation of timber indoors is done after installation. This is fundamentally wrong. Let's look at an example:

installation of panels, area of approximately 100 m2, imitation material, execution - a team of carpenters. So the installation was done a short time Well done guys, they did their best.

It's decided. The men are handy, they themselves will paint. This is followed by the choice of paint by the customer and painting of the imitation of timber inside the house begins ...

Be sure that the quality of the painted surface will not suit you. And why?

it is very difficult to pre-grind on the wall;
if grinding is done, then the appearance of the coating will still not be ideal. It is IMPOSSIBLE to grind in places where the chamfers on the wall are beveled;
the same can be said about intermediate grinding, it is technically impossible to perform it on the wall with high quality;
the product, after a short period of time (for example, after turning on the heating), will slightly change its geometry, this is a natural process, even for a painted imitation of timber, and at the joints the color of the tree will be visible, which the coating layer could not get on.

So, knowing these BUT, it is better to make a choice towards painting the imitation of timber in the workshop of a company specializing in this. Especially to buy ready product with delivery may even be cheaper than the same operations performed by workers at your facility. This purchase will make you happy high quality:

preliminary grinding, including chamfer grinding;
application of adhesive primer;
intermediate grinding;
applying the desired thickness of paintwork materials in micron.

The price of painting imitation timber for installation outside the house will be more expensive than for work performed indoors. The cost varies from the fact that in order to protect against an aggressive environment on the facade, it is necessary to use more expensive paintwork materials with a large dry residue.

Sometimes customers need two-tone painting of timber imitation panels. In the LesoBirzha online store, each product is equipped with a choice of colors according to RAL catalogs, Teknomix, Woodex. Colors are presented as opaque and translucent (translucent).

Sale of painted products, imitation of timber, lining and others finishing panels with delivery in Moscow and the region - this is our forte. You can order the service by phone in the section. Lead time is no more than 14 days. Company guarantee up to 5 years.

We know how to decorate any building so that it looks like a classic log house or wooden building different type. This requires not only relevant Decoration Materials (wooden lining, block house, etc.), but also their proper decoration. We paint timber imitation using modern, reliable and durable coatings, offering:

pre-treatment with primers;
painting with covering paints;
treatment with glazing antiseptics;
oil and wax treatment.

As a result, you get a durable and perfectly protected coating, designed for decades of operation, not afraid of exposure to moisture, direct sunlight, temperature changes, pests, etc.

The price for painting imitation timber depends on the required final result, the amount of work, their urgency and the time of year. Give us a call to book services and check current rates. We guarantee that the amount offered by us will be more attractive than that of other companies providing similar services!

Winter painting

Please note: painting imitation timber in winter period on the street (painting lining, etc. already mounted on the facade of the house) is technically impossible, since at low and negative temperatures it will not be possible to obtain a consistently strong and durable layer of paintwork. However, we have our own paint shop with specialized equipment, drying chambers and optimal temperature regime. Thanks to this, we are able to paint the board at home at any time of the year and put it on the site for installation. Even in the dead of winter!

Proper maintenance of false timber trim includes timely painting of this material. It is important to know what paint to choose in order to paint the imitation of timber with high quality and reliability. Periodic treatment of wood with the right paint guarantees a flawless finish. appearance interior and exterior walls of the house. Paints and varnishes on wooden panels support the safety of products for many years. But in order for such protection of the ball to be correct, you need to know how to paint the imitation of a bar inside the house, which we will try to figure out now.

Types of paints

All paints intended for processing imitation panels are divided into transparent and opaque compositions. The former are indispensable where protection is required wooden panels from harmful effects environment while retaining the original texture of the false beam. For these purposes, varnishes or glazes are purchased that have good protective properties and light decorative effects.

Lacquers, in turn, are divided into:

Acrylic.
Water emulsion.
Polyurethane.
Epoxy.

Lacquers can be completely transparent or with a moderate tint; after application, a film is formed on the finish of imitation timber. Liquid glazes with protective components penetrate deep into the wood and leave a beautiful matte shine and the desired shade on its surface.

Opaque coatings include:

Acrylic paints.
Alkyd emulsions - oil and enamel.
Water-dispersion paints.

If opaque paint is applied to the imitation of timber, the real wood pattern will be completely painted over with pigments.

Interior paints

The primary function of painting imitation timber indoors is a decorative purpose. Interior decoration walls usually do not impose special requirements for protection. The exceptions are rooms with high humidity - sauna, bath, bath, kitchen. It is advisable to treat such premises with stronger paints. In other cases, the emphasis is on the decorative properties of the compositions, for which opaque coatings are selected that create the necessary textural effect.

A range of coloring compositions for internal walls consists of the following items:

Oil paint.
Enamels.
acrylic paint.
Alkyd paint- for baths, saunas and pools.

Painting imitation timber inside the house

Before you paint an imitation of timber inside the house, you must follow the basic rule: when buying paint for a living space, you need to rely on the safety of the coating. When choosing a material, you should pay attention to a trusted manufacturer. Low-quality paint is toxic and releases into the air during the entire period of operation. harmful substances. Knowing how to competently cover the imitation of timber inside the house, a person will protect himself and his loved ones from the negative consequences of painting. Most best option paints for interior decoration - compositions based on water.

On our website you can find contacts of construction companies that offer home finishing and insulation services. You can directly communicate with representatives by visiting the exhibition of houses "Low-Rise Country".

The choice of paint material for exterior decoration

The outer sheathing board can suffer from exposure to sudden changes in temperature, precipitation, and the scorching sun. The main criterion for painting imitation timber outside the house is the protective properties of the coating. Changing the appearance of the panel is in second place here.

Range facade paints under the bar:

Professional - applied using a special technology.
Alkyd.
Acrylic.
Silicone.

The final coating protects the panel from destruction as much as possible. Painting decorative layer for the best effect is carried out in three stages. How exactly to paint the imitation of a bar on the outside depends on many factors - each paintwork differs in price, durability, application technology. To cover the imitation of timber, an acrylic variety of compositions has proven itself well. Facade water-borne paint, bonded with silicone resins, has worthy characteristics: resistance to moisture, cracks, abrasion. However, silicone paint is not so common in household repairs, like other types of coatings, due to the inflated cost. good choice in terms of price - quality are alkyd enamels.

Service life of various paints

One of the criteria for the quality of paint applied to imitation timber is the service life of the coating. The time during which the paint performs its functions is different for each type of coating. The performance of paints to some extent depends on the preparation of the surface to be painted and the technology of coating. In many ways, the durability of paints determines the degree of aggressiveness of the environment.

If during the production of paints all the requirements of GOST were observed, the coating acquires the properties indicated in the description. Respectively, right choice coating guarantees a good result for many years. Performance characteristics Paintwork for wooden bases:

Oil paint based on natural drying oil - no more than 3 years.
Enamel based on alkyd resin - 10 years.
Acrylic paint with polyacrylate binder - at least 8 years.
Water-dispersion coating with organic solvent - 20 years.
Water-dispersion on a mineral basis - 10 years.
Silicone based on silicone resins - 20 years.

If the exterior panels are treated with a clear coat, you should be ready for re-painting after 2 to 3 years.

Paint preparation

The LKM market is crowded today different types coatings. For more quality products The supplier sets rather high prices. It is important to guess correctly with the amount of paint, so as not to further undermine your budget with unnecessary waste. The interior and exterior finishes of imitation timber are covered with paint in several stages, this must be taken into account when preparing paintwork materials. A smooth wooden surface, unlike a rough one, absorbs much less paint.

By multiplying the total area of the walls by the number of layers of paint, you can find out how much you need to purchase paintwork material for exterior or interior painting. Paint consumption may vary if the composition is diluted with solvents.

Preparation of imitation timber for painting

Regardless of the type of paintwork, the surface of the sheathing board before starting painting work should be properly prepared.

As a rule, ready-made imitation panels for timber are already polished and do not require additional machining. Except when you need to remove the old peeling layer of paint, dirt and dust. A clean machined surface improves the adhesion of the paints to the wood. The preparation of the finish also consists in protecting the wood from fungal infections.

Additional mechanical restoration can give the tree a more pronounced naturalness. To do this, it is convenient to use a special brush with stiff bristles, leaving behind small depressions in the wood. This way pre-training appropriate if transparent paint is to be applied.

From the processes of decay and deformation of wooden panels, antiseptic preparations are suitable under the timber. Most paints are perfectly applied to imitation timber, so the primer wooden surface not required. TO painting work proceed after the final drying of the compositions on the surface of the base material.

Interior wall painting

The interior atmosphere of the room largely depends on comfort and coziness. Reach desired result possible with the help original finish under the beam Lumber will retain its decorative properties for a long time if it is periodically treated with special paint to imitate timber inside any room.

Practical Tips:

When mixing the coloring composition, the proportions provided by the paint manufacturer must be observed. Information about this is contained on the packaging of the product.
To work, you need a tool for painting. Ordinary brush is resistant to chemicals and withstand the load.
To avoid smudges and uneven layer, you need to work slowly and carefully, immersing the brush in the composition up to half the bristles. A small amount of paint on the surface is distributed as thinly as possible.
For large volumes, it is convenient to apply the composition with a roller or spray gun.
Re-painting is possible after thorough drying of the first layer of coating.

Modern paints for internal works are non-toxic and do not have a strong odor. It is safe to work with such compounds even with prolonged contact.

Video description

Read more about painting walls from false beams inside - in this video.

Painting the facade under the beam

Exterior painting of imitation finishes according to technology is not much different from interior painting. Specific skills and equipment require the use of professional compositions, so it is rational to entrust such work to specialists. Before painting, wooden panels for timber should be prepared as described above. After opening, the coloring composition is thoroughly mixed. For the spray gun, the paint is pre-diluted with a solvent.

Features of applying exterior paint:

Use protective equipment if necessary.
For work, you need to choose dry and calm weather.

Thanks to the bright and rich shades Exterior decoration of the house always looks fashionable and stylish. The neutral natural color of the facade under the beam is combined with any shade of the roof, the bold colors of the houses need to be matched to the shade of the roof more carefully.

Conclusion

With the help of modern paints, you can ennoble even without that stylish finish beam imitation. And even if, for some reason, the shade of paint does not like it, you can always change it to another tone, and then your house will look new. The range of coatings presented on the modern market allows you to realize any design ideas.

The desire to update the appearance of the house arises in any homeowner, and to give a beautiful appearance to the home, you can paint the walls. Houses finished with siding or stone do not need to be painted, and this is rather their minus, since you can change the appearance of such a house only by changing the finish.

It is a completely different matter if the house is sheathed with an imitation of timber or logs. Painting a sheathing board is one of the prerequisites for such a finish. This is where the questions arise, how and with what to paint the imitation? How often do you need to repaint? This article will be useful to those who are going to paint imitation timber or logs inside and outside the house.

1. Choose a coating to simulate a beam:

Glazing coating.

Our choice of coating will be directly related to the types of paints and varnishes. They are:

Glazing (emphasize the structure of wood).
Covering (hide wood structures).

Glazing coatings:

These coatings do not change the appearance of wood and favorably emphasize its structure. These include: varnishes, impregnations, azures, oils, waxes, etc. They can be seen in action in numerous photos on the Internet. This type of paint and varnish materials, in addition to preserving the appearance of wood, also has vapor permeability, i.e. sheathing panels with such a coating will not retain moisture, and this will prevent them from rotting. In this group, I would especially like to note such materials as Finnish Teknol 1888 and German Deco-tec 5420, because they are the most popular for painting wood paneling in terms of price / quality ratio. Of more budget materials we recommend paying attention to domestic material Neomid Bio Color Aqua.

Covering coating.

Covering covers:

This type of coating covers wooden panels and decorates them, hiding the wood structure (under the plastic). Such coatings include: acrylic and water-dispersion paints, enamels, etc. These paints and varnishes very reliably protect wood from the effects of UV radiation (burning) due to the presence of a large amount of pigment (color). From a high-quality professional line of covering paints, it is worth highlighting, first of all, the Finnish Nordica Eco 3330-03, Deutsch Deco-tec 5450, as well as Rubbol® WF 361.

2. Differences in painting the sheathing board outside and inside the room:

Painting the facade of the house interior spaces differs in its purpose. The facade is painted to protect it from the harmful effects of the sun, water, wind, temperature changes, and only the secondary function of such a coating is decorative. Interior painting is primarily a decorative function, but even here there are subtleties, for example, for rooms with high humidity, protection should still be primary.

The process of internal and external painting differs in the number of applied layers. The interior finish is covered, as a rule, in two layers, and the exterior, most often, in three (depending on the manufacturer of paintwork materials, the painting technology and the number of layers may vary, so we recommend consulting with specialists). For interior work, materials such as Finnish interior waxes and varnishes are very popular (unconditional sales leader - it is a colorless or whitish varnish Teknocoat Aqua 2550-02), because they are distinguished by their hypoallergenicity, environmental friendliness, protective properties, incl. from moisture, as well as its ease of application.

3. The main stages of painting imitation timber / logs:

All work on painting the imitation of timber can be divided into the main stages:

Sanding - removal of dirt / damage, opening the pores of wood:*

Preparatory sanding of wood is a key to successful painting and guarantees good adhesion of the paint material, as well as reduces paint consumption and evens out the absorbency of the applied material. Thus, it gives a unique appearance of timber/log imitation, favorably emphasizing the advantages of wood, and also hides its shortcomings and natural defects. You may come across a proposal to use an iron brush for sanding, so that the composition penetrates deeper into the wood. This method is also called "brushing" - with imitation of this method, a soft layer is removed and the tree becomes more textured. It is recommended to grind at least P100 grit - for exterior finish and P100-P180 - for internal. Subsequent treatment with an antiseptic should be carried out within 1-2 days after the completion of grinding.

Dedusting imitation timber / log:

Removal of dust and dirt after grinding, by blowing or brushes.

Antiseptic treatment of the sheathing board from all sides, including end cuts and saw cuts (spray/brush):

This is what happens if you forget about the antiseptic - a fungus forms right under the paint and destroys the wood.

Regardless of where the imitation will be used (outside or inside), we strongly recommend protecting the wood from blue, rot and fungus with an antiseptic composition, preferably from the same manufacturer , which is the final material.

IMPORTANT: We advise you not to neglect the bioprotection of wood even during internal work, in view of the fact that often the sheathing board has traces and lesions already from the moment it arrives from production, and also because coniferous woods are predisposed to these infections. The most popular from the line of high-quality professional materials: Finnish water antiseptic Teknol Aqua 1410-01(can be used for both outdoor and indoor work), Zowo-tec 100(for outdoor work), Zowo-tec 245(for interior work) and Cetol® WV 885 BPD(for external and internal works). From a more budgetary segment of the market, we recommend that you pay your attention to Russian materials: Neomid 440 Eco(for outdoor work) and Neomid 400(for interior work).

Protection of ends, end cuts and saw cuts with a special tool (1-2 layers, depending on the manufacturer's technology):

The most vulnerable place for wood and imitation of timber / logs in particular are the ends and end cuts and saw cuts, they are prone to moisture penetration, and as a result, it is from them that the destruction and biodamage of the tree begins. To protect them, they use special means for sealing and “sealing” the ends from moisture penetration, such as, for example, Finnish Teknol JRM.

It is recommended to apply the first layer of finishing material on a imitation that has not yet been mounted, because only in this case it will be possible to paint over the tenon-groove joint, which is most susceptible to moisture in the “unpainted” state, with sufficient quality. This is also done because the panels will dry out, especially indoors, and the seams at the junctions will diverge - the “non-painted” places will become visible.

IMPORTANT: If possible, then facade works it is best to apply the first priming layer of paintwork materials to the sheathing board from all sides in order to protect it as much as possible from the possible penetration of moisture and other factors that destroy the tree.

Application of the second (if necessary, following the manufacturer's technology and the third) layer of finishing material (spray/brush):

Finishing layers are best applied already on the mounted imitation - to ensure the highest quality painting and eliminate defects that can be applied to the coating during the installation of the board. If possible or necessary (sometimes the end composition is applied as an independent finishing material), apply paintwork materials to the ends of the sheathing panel to make the color uniform (if the ends of the imitation are open).