Connection of polypropylene pipes: methods and features. Methods for joining polypropylene pipes How to properly connect polypropylene pipes

Metal pipes have become obsolete for some time. They are being replaced by plastic counterparts. According to their operational characteristics they are not inferior to metal ones, and sometimes even surpass it.

Correct connection of a metal pipe with a polypropylene pipe becomes a guarantee that the system will work without interruptions, with maximum reliability.

How to connect polypropylene pipes with metal ones?

Situations when it is necessary are not so rare .

To understand how to properly connect polyethylene pipes with polypropylene or metal watch video tutorials posted in this article.

There are several ways how to correctly make a connection.

With the presence of a thread. Assumes that you are using fittings that look like couplings. One end is provided with a metal thread, and the other with a cut, with perfect smoothness.
Flanged type. When the stud bolts tighten the flange structures themselves. They will help you understand how to connect polypropylene pipes, videos will make the process more intuitive.

We install threaded fittings

These types of connections are relevant if pipes of medium, small diameter are taken together. Their size should not exceed 40 millimeters.

The thread on the fittings is present not only on the inside, but also on the outside. It is needed to secure the metal sides and ends to parts. The smooth cut of the sleeve is located on the opposite side. It involves soldering plastic.

Fittings are mounted using a simple technology.

The workpiece is cut at a right angle, in the place where the joint is supposed to be. For processing the edge, use solid oil. Then take a thread cutter, and finish processing.
After that, they must be cleaned so that there are no metal shavings. For the future joint, one cannot do without sealing, which implies the use of FUM tapes or tow.
The fitting structure is screwed onto the cut part, with preliminary preparation... It doesn't take too much effort. The part can crack if you press too hard with the tools.
The smooth cut is screwed onto the plastic pipe. Easy to understand how to connect polyethylene pipe with polypropylene.

The material for sealing is laid out along the thread so that at least 1-2 turns are covered with it.

Video: how to connect a pipeline

Installing flanges

This option is more suitable for those who work with large diameters. Thanks to him, during operation, there are fewer problems with access if it is necessary to do cleaning.

The flanges look like flat discs supported by straight braces.

The installation of pipes in the system consists of several stages.

It all starts with creation even cut at the ends of the blanks. The main thing is that there should be no dust and shavings inside.
Then they move on to putting on the flanges on the sections prepared in advance. We place rubber gaskets between the places with the discs.
Bolts are used to connect the flanges to each other. It is important that the tightening is uniform, without applying much force.

Polypropylene pipes and their connection

The ends of pipes made of this material are exposed to high temperatures in order to connect the products, to carry out the docking. You can also use gluing or special fittings.

Video: how to solder correctly

How to solder the structures?

Polypropylene workpieces cannot be joined without a special welding machine called "iron". It works when connected to a regular electrical network.

It is better to purchase the materials themselves with a small margin, in case of possible errors.

The process consists of several stages. This will allow you to understand how to solder a polypropylene pipe.

Several cuts are made where joints will be located in the future. A thorough cleaning is also required for the ends. Special marks are made on their surface with a marker. They indicate how deep the parts should be inside the heating apparatus. The soldering iron temperature must be at least 270 degrees.
Strictly perpendicular connection of nozzles with a hot soldering iron. The same is done with the ends of the other joints.
Wait 10-15 seconds until melting is complete. Then they get rid of the nozzles, and the parts are again connected together. They are lightly applied to each other, but turning is unacceptable.
The parts for joining must be left in one position for a while until they cool down.

Video: learning how to solder

Socket brazing is an option that is used for pipes with 40 mm and larger diameters. But such work is recommended to be trusted by specialists, only they know about all the features.

It is better to heat the connecting elements from the inside and pipes from the outside. Then it will be easier to create knots with high strength. Otherwise, small bumps form inside, due to which the permeability decreases. Air purging of the structure will allow you to forget about such problems.

Features of the "cold" method

Compression fittings are assumed to be used here. From the tools, a conventional crimp wrench is enough.

Assembly process looks like that.

As usual, work begins with the cuts at the ends. After that, you need to check if the edge is in a perpendicular position. Cleaning the ends from burrs is carried out with a wire washcloth or fine-grained sandpaper.
The coupling nut is put on one of the ends of the pipe. The thread must go to the fitting. Then they move on to the operation of rings with compression. They also go to the fitting side, but with long bevels.
The fitting is strung on the surface of the butt-end prepared in advance. The part is inserted into the inner surface until it stops.
The swivel nut is then fully tightened. The system is checked for leaks.

Video

What points to pay attention to when welding?

Professional soldering irons are quite expensive. Better to get inexpensive "hobbyist" options if the job is fickle. These usually have several running attachments at once. You can rent tools. This will not affect the quality of the final connections.

The stable stand has become required element for almost all soldering irons. Even professionals only make connections if the instrument is stable. It takes no more than 10-15 minutes to heat the working surfaces.

There are only 2 parts in the connecting nozzles - a drone on which the coupling is heated, as well as a sleeve, inside which there is a pipe with a drone.

The parts of the nozzle are installed on the soldering iron when it is still cold. And only after that the device is connected to the network. Work should be started only when the indicators go out.

Video

This occurs during the second heating cycle. But the warm-up time is determined by several factors:

Pipe type.
The thickness of the walls.
The diameter of the structure.

All these values are usually indicated in the table that comes with soldering iron sets.

Sewer systems and features of their connection

Many people connect plastic pipes not only with metal, but also with cast-iron counterparts.

Such joints are structurally different from others. You will need to purchase special components:

Seals.
Corrugation.
Cuffs.

The selection and purchase of suitable components should not cause any special problems. But you can also use scrap materials if you find suitable option It does not work.

For example, a seal is cut out of the microporous rubber. A long narrow tape must be placed in the gap between the elements to be connected. A dull wide screwdriver will help seal this material.

Video

Coinage is unacceptable for several reasons. It can deform plastic pipes, interfere with the creation of sealed joints. But even after completing the work, the likelihood of leaks will remain high.

Cement mortar also does not have a high service life. Various materials have different coefficients of thermal expansion, and this difference has a negative effect on the design.

In cemented joints, cracks appear too quickly, such structures simply lose their integrity.

Plastic pipe rolls are sometimes combined with copper ones, but this option is extremely rare. The connection of a metal pipe with a polypropylene pipe is more common.

Recordings

With polypropylene, it is important to know that High Quality when carrying out such work, it can be achieved only when the wall thickness of the products is taken into account. Modern technologies allow you to create fairly durable and reliable communications from such pipes. They do not undergo corrosion processes, which is why they are so widespread. Such manipulations can be carried out in one of several ways, however, the work can be classified into two categories:

soldering method;
use of fittings.

Connection methods

If you decide to find out how to connect a polypropylene pipe with a polypropylene pipe, you need to figure out the methods. For example, thin-walled pipes can be threaded. If you need to equip the feeding system cold water, the temperature of the environment in which does not exceed +20 ° C, then products with the PN 10 marking should be used. The same applies to laying underfloor heating, in which the temperature does not exceed +45 ° C.

If it is necessary to equip a cold water supply system that will be transported at increased pressure, pipes with PN 16 marking should be used. This recommendation is relevant for pipelines with reduced pressure. Most quality option the connection is welding, it can be used for pipes PN 20, which are able to withstand temperatures up to +80 ° C. Their walls are thicker than the previous ones.

The same connection method is also suitable for PN 25 - pipes reinforced with aluminum foil, which are intended for systems central heating and hot water... Pipes with this marking will be able to withstand temperatures up to +95 ° C. Connections can be permanent when welding is used; and also detachable, in this case a thread is used.

Threaded connection

Before connecting a polypropylene pipe to a polypropylene pipe, you need to figure out which method is best to use. For example, for a threaded connection, you need to prepare threaded fittings, because you cannot cut threads on polypropylene products. The connection is carried out using a special tape, which will make the joint strong and reliable.

Fittings used

If you decide to use a threaded connection, then you will need:

solder couplings;
triple square;
combined crosses;
couplings;
squares 90 °;
combined squares;
ball valves;
solder squares at 45 °;
stubs;
external thread adapter;
water outlet;
PP fittings with factory thread.

Welded connection

If you are thinking about how to connect a polypropylene pipe with a polypropylene pipe, then you can use the welded method. However, it is important to consider that the connection will be permanent. When melting, the molecules of one part move to another, diffusion occurs. From heating by an electric welding machine, the parts are organically interconnected, because they have the same chemical composition.

To carry out the work, you should prepare:

soldering iron;
welding machine;
polypropylene fittings and pipes;

In addition to the listed tools and materials, you should prepare a hacksaw or metal scissors, a tape measure, couplings like faucets, corners and pipes. It is important to stock up on fum tape. As for the welding machine, it will consist of heating element and welding nozzles, the diameter of which varies from 16 to 40 mm.

As soon as the indicator goes out, you can start work, because this will be a signal that the required temperature of 260 ° C has been reached. This will take approximately 15 minutes. If there is a subzero temperature environment, then welding work must be abandoned. If it is necessary to weld pipes with a diameter of 60 mm, use the socket welding method. For a more impressive diameter, butt welding is suitable, which does not involve the use of additional parts.

For pipes with diameters ranging from 16 to 50 millimeters, a hand-held soldering iron should be used. More impressive diameters will be connected with a mechanical welding machine. The ends of the pipes should be well heated with removable sleeves, then all that remains is to press the elements together, applying little effort. This effect should last for a few seconds.

Welding with an electric coupling acts as a better option in comparison with the previous method, because the process is controlled by the program. The quality of the joint will be higher, and the need for fixation will disappear. Devices with electrodes are used to supply voltage to the heater inside the sleeve.

Before connecting two polypropylene pipes with the socket method, it is necessary to cut the products at right angles.

Next, the master should apply a mark to the depth of the socket, to which 2 mm should be added. Joining products begins with warming up using a special device. After the parts are connected to each other. And if the polypropylene has an aluminum layer, then the connection can be made through the perforated holes. This makes it possible to significantly increase the strength of the PN 25 pipe.

Using butt welding

Before connecting polypropylene pipes to each other, you should think about which method is best to use. Butt welding may be suitable, which will allow you to connect pipes together for outdoor sewerage... This approach is relevant if the pipe wall thickness exceeds 4 mm.

At the first stage, the weld points should be trimmed to parallelism. After that, it is necessary to carry out heating and ensure accuracy with a centering device. Welding should be accompanied by ventilation of the room, because polypropylene emits carbon dioxide and water vapor, and also smokes.

Solderless connection

Quite often, novice home craftsmen ask themselves how to connect polypropylene pipes without soldering. For this, fittings are usually used made of the same material as the pipes. If the heating system includes fiberglass reinforced mains, other types of products will not work.

You should stock up on polypropylene fittings that are reinforced with fiberglass. An exception is the case when there is a need to combine polypropylene with another material. In this case, threaded elements are used, for example, "American". Before connecting polypropylene pipes without a soldering iron, you should ask what fittings can be found on sale for arranging water supply and heating systems, among them:

Y-shaped;
straight;
T-shaped.

The use of these elements is necessary taking into account the mode of application and the situation. By the type of connection, several types of shaped products are distinguished, namely:

compression (crimp);
welded.

Compression polypropylene fittings are supplied in finished form, there is no need to collect them additionally. Compression fittings have advantages over welded fittings. They consist in:

ease and simplicity of installation;
no need to use welding equipment;
installation options polypropylene fittings under any weather conditions, because they are not afraid of negative temperatures;
no need for a specialist to have special skills for installing crimp fittings.

If you are thinking about the question of how to connect polypropylene pipes at home using fittings, then you should familiarize yourself with the technology. At the first stage, construction tools are prepared, namely:

gas and adjustable wrenches;
screwdrivers;
open-end wrenches;
sealant;
special scissors;
pipe cutter;
bevelling machine;
caliber.

You can think about the placement of pipes that can be in the wall or on top of it. There should be no hard corners in the circuit. Product flexibility is achieved with construction hair dryer... If you decide to use polypropylene pipes for heating, you should know how to connect them.

The connection point must be sealed in any way convenient for you. This can be done using fum tape. Then the system is assembled according to the principle of the constructor; at the corners and in the places where the flow is distributed into several parts, special elements such as corners and tees should be used.

Conclusion

Now you know how to connect polypropylene pipes with fittings. However, as practice shows, the welded method is more reliable, because diffusion occurs in the process, which ensures the reliability and strength of the system.

Every year, more and more often the design of plumbing and heating systems in apartments and private houses it is carried out using polypropylene pipes. Modern technologies for their manufacture allow you to create durable communications that do not corrode. At the same time, the main task facing the builder is to create a high-quality connection of pipes to each other, since the reliability of communication systems will depend on this. Therefore, below we will consider the main methods of connection polypropylene products.

Figure 1. Special fittings have a threaded thread on one side and a solder socket on the other.

Methods for joining polypropylene pipes

The installation of plastic pipes is quite easy and quick, so that even a person without special training can cope with this work. Connections can be detachable (threaded) and one-piece. In the first case, special threaded fittings are used, and you will not be able to cut the threads yourself. Therefore, a sealant or Teflon tape is used to create a secure fit.

Figure 2. Installation of polypropylene pipes using compression fittings.

Welding joints are stronger and more reliable, however, to create them, special equipment is required - an apparatus for welding polypropylene. In turn, welding can be socket or butt welding. Each method has its positive and negative sides.

In most cases, thin-walled products are connected in a collapsible way. PN 10 pipes are widely used for the construction of underfloor heating, as well as for the supply of cold water. high blood pressure products PN 16 are used for water supply. Pipes with diameters PN 20 and PN 25 are recommended to be joined by welding.

Back to the table of contents

Dismountable connection of polypropylene products

For docking plastic products With metal elements(mixers, meters, etc.) special fittings are used, on one side of which there is a threaded thread, and on the other - a socket for soldering (Fig. 1). In this case, the thread can be both external and internal.

Installation of polypropylene pipes with steel using fittings is carried out as follows:

Figure 3. Flange connection diagram.

End metal product lubricated with oil or grease, after which the thread is cut (internal or external). If the fitting has internal thread, then the pipe must have an outer, and vice versa.
Tow is wound on the thread and treated with silicone.
The fitting is screwed on and clamped with a wrench, but without applying excessive force, as otherwise it may crack.
A polypropylene pipe is inserted into the other end of the fitting, after which it is soldered.

With the help of such fittings it is very convenient to create various bends and turns of communication systems. If it is necessary to slightly change the configuration of the fitting, it should be warmed up to a temperature of about 135 ° C.

Another type of collapsible installation of polypropylene pipes is their joining using compression fittings. They are easy to use and can be used to design both cold and hot water supply. In this case, there is no need to use welding equipment. It is enough to have on hand pruning shears and a set wrenches.

Installation of polypropylene pipes using compression fittings is carried out as follows (Fig. 2):

a crimp nut is installed at the end of the pipe;
a split-type ring is installed on top of the nut so that its edge is at a distance of 1 mm relative to the pipe cut;
the plastic pipe is put on until it stops and fixed on the fitting;
the crimp nut is installed using wrenches.

Figure 4. The welding machine has sleeve-shaped nozzles for heating the outer surface of the pipe and a mandrel for heating the inner surface.

Flange mating is used for polypropylene products with a large cross-section. Such a connection makes it possible, if necessary, to easily disassemble any section of the pipeline and eliminate the malfunctions that have arisen (Fig. 3). Also, quite often the flange joint is also used for the installation of plastic products with metal ones.

Installation of flanges is quick and easy. First, the end of the pipe is cut straight, after which a flange and a rubber gasket are put on it. The same operation is performed with the other end of the pipe. After that, both flanges are bolted together.

Back to the table of contents

Welding connection of polypropylene pipes

For welding products with a cross-section of up to 6.3 cm, the preferred type is socket or socket welding. In this case, the pipes are joined using the 3rd part - the coupling.

To connect polypropylene pipes with a diameter of more than 6.3 cm, it is recommended to use butt welding.

Modern technologies allow using polypropylene pipes to create reliable and durable communications. They do not corrode. Therefore, they are widely used. But in this case, the important point is to connect polypropylene pipes with your own hands. This can be done by soldering or using a method without welding. Therefore, it is not necessary to use a specialist. Let's understand each in more detail.

And this process will require welding machine, which experts often refer to as an "iron". This device is a simple device that operates from the mains. In the kit, it often has nozzles of different diameters with instructions.

The connection of such products occurs when high temperature is applied to their ends. But there is one subtlety here. The pipes are heated from the outside, and the connecting elements are heated from the inside. This is the only way to get strong knots.

Phased process:

First, the soldering iron turns on, it must be heated to 270 degrees. Products are cut into desired pieces and cleaned. You can make handy notes to understand how deep to immerse them in the apparatus for heating.
Smoothly insert the pipes and connection elements onto the device nozzles. This is also important for a good quality soldering.
After the element and pipe have melted, they are removed from the device and connected to each other. The evenness of the soldering is also important here. You need to press down slightly, but not scroll around the axis. Pressure also affects the quality of the solder.
After joining the elements, they need to be held for several minutes in a stationary state.

When performing manipulations, you should pay attention to one more important nuance... The inner surface of the seams should not lose permeability. Indeed, when melted, a small tubercle appears, which is dangerous if the products are of small diameter.

Strong build-up of material caused by excessive heating should also be avoided. To check the patency of the pipe, you can blow through it and let water through it.

It should be recommended that if you do not have experience in soldering, you can practice first before proceeding with the basic manipulations. And therefore, it is recommended to purchase materials with a margin, because in addition to training, for sure, a marriage can occur during the main work. And it is highly undesirable to run or go back to the store during the process of soldering. For getting more For information on do-it-yourself soldering, you can also watch a video on the topic.

As for the device itself, it is not necessary to buy it. The device can be rented from someone.

However, this method without welding has one significant drawback. The time to complete the procedures is significantly longer in comparison with welding. And this must be taken into account when choosing a method for connecting pipes.

To the content

Conclusion

In a word, there is nothing terrible or very difficult in connecting polypropylene pipes with your own hands. As with most technologies, it requires a clear and correct execution established technological standards. To do this, you can additionally familiarize yourself with the video materials. Then the process will be performed not only quickly, but also efficiently. And this is already a guarantee of the durability and reliability of the resulting water supply or heating system.

In this case, it is not necessary to use welding. After all, you can get by and alternative way... However, the disadvantage of this solution will be the increase in the time of all work. Therefore, it is necessary to choose a method taking this moment into account. Then everything will go smoothly, and the system being built will acquire the required strength and reliability.

dizain-vannoi.ru

How to connect polypropylene pipes

Polypropylene pipes are much more convenient and practical than their metal counterparts. Their main advantages:

easy installation;
not a lot of weight;
not subject to corrosion;
not expensive.

Due to their advantages, they are becoming more and more popular.

Another important advantage of this material is that you do not need to hire anyone for installation, you can do everything yourself. Therefore, if you need to replace the old leaking water supply system, you can safely get down to work. You can connect polypropylene using soldering or using cold method.

Method 1 - soldering

This method implies the presence of a special welding machine, which specialists call "iron". An iron is a kind of a soldering iron powered by electricity. It comes with attachments different diameters.

If you are not going to professionally install a water supply system, you do not need to buy such a device. It can be rented, usually all sellers provide this service. The process of soldering polypropylene pipes is not complicated.

Video: How to properly solder pipes with your own hands

Soldering technology

Polypropylene products are connected under the influence of high temperature. The pipe itself must be heated with outside, and all connecting elements from the inside. Thus, a strong connection is obtained.

Soldering stages

We turn on the soldering iron, it should warm up to 270 degrees C. While heating occurs, you can cut the necessary workpieces and clean them. For convenience, you can make notes that will show how deep they should be immersed in the welding machine. Cut them off with a special pipe cutter or an ordinary metal hacksaw. If cutting is done with a hacksaw, attention should be paid to burrs and if they remain, they must be cut with a knife.
After the soldering iron has heated up to the required temperature, insert the pipe and connecting elements onto its nozzles. For high-quality soldering, all elements must be inserted exactly. Movements should be quick and confident. Parts that are exposed to heating must not be moved or twisted.
When all the elements are well heated, they are removed from the soldering iron and connected to each other. This is also done with quick and confident movements. Parts are connected with light pressure (no rotation) and fixation for 10-15 seconds.
After this procedure, you can proceed to soldering the next node and so on until the bitter end, when the water supply is completely welded.

Method 2 - no soldering

This is a connection method that does not require soldering equipment. With this method, there are two options: connection with compression fittings and the so-called "cold welding".

For the version with compression fittings, only a special crimp wrench is required. This wrench is usually sold with fittings.

If you stop at the option - "cold welding", then you need a special "aggressive" glue. It is applied to the parts, after which they are connected and pressed, fixing in this position for a few seconds.

The connection of polypropylene pipes with glue is only suitable for water supply with cold water... The connection of polypropylene pipes without soldering has a big drawback, namely, in comparison with soldering, the time for installing the pipeline is significantly longer.

In conclusion, I would like to say that there is nothing difficult in the independent connection of polypropylene pipes. Like most others construction works, you will be required to comply with all technological standards in good faith and accurately.

Then the process of joining polypropylene pipes will be completed quickly and, most importantly, with high quality. And the quality of the work performed is the key to durable and reliable work water supply and heating systems.

Watch the video: How to properly solder polypropylene pipes with your own hands

alina-sharapova.ru

How to connect polypropylene pipes without soldering?

Owners of private houses and apartments often face the problem of pipeline rehabilitation. Many of them decide to replace old products with polypropylene pipes. Even a person without special skills can mount such a water supply system. However, first you need to figure out how to connect polypropylene pipes without soldering.

Cold connection of polypropylene pipes

General information

During the construction of private houses, polypropylene plumbing began to be installed more and more often. The popularity of such products is justified by their low cost, long operating period, ease of installation and the absence of rust. They are used to create water supply and heating systems. Three types of products are produced from polypropylene:

copolymer;
block copolymer;
homopolymer.

The above products can be connected different ways... Many people use the connection of polypropylene pipes without soldering.

Advantages and Disadvantages of Solderless Connection

This method has several serious advantages, due to which some refuse to solder pipeline elements. These include:

Small financial costs. During soldering, you have to use expensive equipment, which is not available to everyone.
Ease of installation. It is much easier to mount pipeline elements without soldering, since you do not have to use a soldering machine and monitor such parameters as the pressure and temperature of soldering polypropylene pipes.
The rate of restoration of the water supply system. If the products were soldered together and there was a serious breakthrough, then the recovery can be greatly delayed. It will take time to wait for a specialist with the right equipment. This problem will disappear if you make connections in other ways.

However, the connection of plastic pipes without soldering has one serious drawback - the installation of the pipeline can take much longer.

Connection methods

Tie-in into a polypropylene pipe without soldering is carried out by different methods. The choice of method directly depends on the purpose of the pipeline, the size and type of elements used. The most common connection methods include:

Use of flanges. This type of connection is quite reliable. The products are connected with bolts that are screwed into special holes in the flanges.
Use of fittings. These products are made from cast iron or steel. They are used when working with small diameter pipes. The advantage of fittings is that they allow you to make transitions between parts of the pipeline and connect them at different angles.
Use of couplings. For their use, threads are made on pipes and wrapped with tow to make the connection more tight.
Gluing. This method cannot be used for plumbing with hot water... During installation, glue is used, which is applied to the parts.

Fitting

If the technology of soldering polypropylene pipes is not used, then they are connected using fittings. They are connecting elements that are most often installed at bends and branches of the pipeline. Fittings consist of a body, a cover, a sleeve and a clamping ring in a special socket. They also have a seam ring with which the polypropylene pipe is fixed.

When installing a water supply system, it is necessary to use pipes that comply with all standards. "

The ovality of the cross-section of the products should be within 1% -1.5% of the diameter. If during operation fittings with a diameter of less than 50 mm are used, then the installation is carried out manually.

Before connecting plastic pipes without soldering with fittings, you must adhere to step by step instructions:

Cutting pipes. They must be cut at right angles.
Burr removal. The surface of the products that will be placed in the fittings must be perfectly flat.
Installing the nut. It is removed from the fitting and installed on the pipe, after which the clamping ring is put on it.
Pipe installation. It enters the fitting until it stops and is fixed with a nut and a clamping ring.

Flanges

Flanges are used when it is necessary to make a connection of plastic pipes without soldering. Such a connection is very reliable, as it can withstand temperatures up to 650 degrees Celsius and cope with pressures up to 20-30 MPa. The diameter of the flanges reaches 3000 millimeters. At the time of selection optimal size the pressure of the pipeline and the material of the products from which it will consist are taken into account.

Flanged PP pipe

Flanges are available in cast iron or steel. They can be:

Cast. Are part of the design of a fitting or pipe.
Welded. It is made in the form of a washer, which will have to be attached to the structure yourself.

During their use, the following recommendations must be followed:

At the place where the elements of the pipeline will be connected, you need to make a special cut. In this case, it must be done so that burrs do not appear.
A gasket is installed on the cut, which should protrude 15 cm.
The flange is attached to the gasket and connects to the flange that is installed on the second pipe.

Also, while performing such work, the following nuances must be taken into account:

it is impossible to install two or more gaskets on one flange, as due to this connection it will become less tight;
during the installation of the water supply system, it is recommended to use rag cardboard gaskets;
the bolts should not protrude much above the nuts;
gaskets must be installed in such a way that their external cross-section does not touch the bolts.

Couplings

They are used during the creation of a pressure and free-flow pipeline. It is quite simple to connect plastic pipes without soldering using couplings with your own hands. To do this, it is enough to adhere to the following rules:

the edges of the elements to be connected are cut in such a way that the cut is perfectly even;
the place where the coupling will be installed is indicated by a marker;
the coupling is covered with special grease;
the sleeve is put on the pipe with the help of the mark made by the marker.

Connection of PP pipes with a coupling

Gluing

The connection of plastic pipes without soldering fittings can be done with glue. Before this, the surface of the products must be prepared. First you need to cut the product with special scissors and clean it from the burrs with sandpaper. All fittings and bonding locations are marked with a marker. After that, you can start gluing, which consists of the following stages:

Degreasing. Before using the glue, you must use a cleaner and degrease all areas where it will be applied.
Glue application. The adhesive should be applied in a thin layer to the places where the fittings will be installed.
Pipe installation. They are installed all the way into the fittings. This must be done very carefully so that the parts do not wiggle too much.
Drying. The glue will dry completely within 15-20 minutes. However, it is only necessary to fill the pipeline no earlier than in a day.

Bonding PP PVC pipes

Conclusion

Polypropylene pipes are connected in various ways. Having figured out how to connect polypropylene pipes with each other and with metal pipes, you can independently mount the pipeline.

How to connect polypropylene pipes

Polypropylene pipes are used for the installation of water supply systems, for the installation of irrigation systems and for heating. The popularity of the material and various areas of use are due to its characteristics: strength, durability, ease of connection. An important argument in favor of polypropylene pipes is their price, which is significantly lower than that of metal-plastic or metal counterparts.

The service life of a plastic pipeline with cold water is 50 years, such an impressive figure makes it necessary to replace outdated lines with just this type of highways. Tightness of joints - the most important factor for any pipeline, therefore, the viability of the system depends on the quality of the installation. In the article we will talk about how to connect polypropylene pipes with metal, polyethylene, steel pipes, and also consider different options welding.

Materials and tools

Soldering iron for welding

If you decide to save on installation services and do it yourself, then you need to buy or rent a special soldering iron with nozzles. In addition to him you will need:

tape measure and marker for marking;
scissors for cutting plastic pipes;
stripping for pipes.

There are several types of polypropylene pipes that differ in the area of use:

PN 10, 16 - used for laying cold water pipes;
PN 20 - universal pipes with thick walls, they are able to withstand hot water up to 80ºC, therefore they are suitable for heating installation;
PN 25 is a composite pipe with a metal or nylon interlayer, which is peeled off when brazed. It is used for heating systems, the final heating temperature is 95 ° C.

Polypropylene pipes and fittings

A distinctive feature of the connection of polypropylene pipes is the absence of joints directly between the pipes. If their diameter is less than 50 mm, all parts can be connected with fittings for various purposes:

couplings - connect sections of the same diameter;
crosses - used to create branches;
plugs - seal the end of the pipe;
adapters - are used to connect pipes of various diameters;
choke fittings - connect to flexible hoses.

How to work with a welding machine

Welding polypropylene

The principle of connecting the pipeline is to heat the elements and quickly connect them. Household pipe welding machines have a power of up to 1 kW. It is enough to quickly and efficiently heat the material, but more powerful and expensive devices are used for industrial purposes. The soldering iron comes with nozzles that match the diameters of various pipes. Heating of the pipe occurs from the outside, and the fitting from the inside.

The work of the soldering iron begins with turning on the network and setting the desired heating temperature, depending on the diameter of the plastic pipes being welded. The average value is 250-270 ° C. Such heat requires caution, touching a hot part will cause burns, for safety reasons it is worth wearing gloves.

Soldering process

A hacksaw or sharp scissors is used to cut pipes, which do not deform the plastic. The incision is made at a right angle. If burrs appear on the end, they are carefully cleaned off. After cutting, the marking of the soldering depth is made. You need to measure the section of the pipe that will go into the tee or coupling, and put a line with a marker. The value of the size of this section depends on the diameter of the pipes; the larger it is, the greater the immersion in the connecting element.

Pipe stripping tool

If you have to work with reinforced pipes, the procedure changes. Before soldering, it is necessary to clean upper layer pipes consisting of aluminum foil, basalt or nylon fiber. Special tool designed so as to remove the desired layer size.

Thorough removal of the foil is very important, a small amount of material on the pipe will spoil the tightness of the soldering.

Reinforced pipe

The soldering iron with nozzles matched to the diameter of the pipes is installed on a flat and solid surface. On both sides, a pipe and a fitting are simultaneously put on the heated nozzle, deepening to the intended line. The heating time of the plastic depends on the size of the pipes: for 20 mm, 6 seconds are enough, and for 32 mm, it will take 8 seconds. Having withstood the set period of time, the elements are removed and firmly fixed into each other, while rotational movements cannot be made. For a strong adhesion of the joint, it will take from 4 to 10 seconds, during which time the polypropylene will harden and form a permanent connection.

Temperature and heating time

Failure to comply with the recommended heating time leads to the formation of leaks - in case of insufficient heating or sealing of the interior space - in case of excessive overheating. You should not try to remove the sag that has appeared immediately; the molten plastic is more deformed in this case. It is necessary to wait until it cools down and cut off the excess.

Try to solder less by weight

Without experience, in order to understand how to properly solder pipes, several training joints can be made. It is convenient to work with short connections by placing the welding machine on the table; in this position, you can perform all possible job, and the connection to a partially laid highway is more difficult. The soldering iron nozzle is put on a fixed polypropylene pipe, and a tee is inserted into the second part, while the apparatus is kept on weight. When executing the trunk, you need to monitor the order of the connections being made. Try to avoid docking in hard-to-reach places where it will be difficult to use a soldering iron.

It is important to keep the material clean and dry, because dirt and moisture will reduce the quality of the pipe connection. Even a small amount of moisture deforms the material when heated. Chemical composition pipes from different manufacturers may not match, this will lead to a leaky joint. All material - pipes and fittings - must be purchased from a single source.

The temperature in the room where the polypropylene is installed should not fall below + 5 ° C.

Crimp connection method

Connection diagram using a collet fitting

Docking the pipeline using the soldering method is reliable and durable, it is impossible to disassemble it, and sometimes this is exactly what is required for repair. In addition, it is not always possible to purchase or lend a welding machine; in such cases, they use the method of joining polypropylene pipes without soldering. For this, fittings with a thread and a pressure ring are used. They are called collet or crimp, such a connection is able to withstand a pressure of sixteen atmospheres.

For a mechanical connection, it is necessary to purchase several additional parts: elbows designed for joining various diameters, a tee, solder and combined couplings, having an external and internal thread, plugs, adapters with external thread, elbows and tees with union nut, ball valves, various fittings with factory thread.

Clamping fitting structure

To ensure tightness, the joints and seals are generously lubricated with silicone.

For work, you need a crimp wrench, which can be purchased at the same time as the fittings. Cutting off the right part pipe, firmly insert it into the fitting, wrap the thread of the element with thread for sealing and tighten the ferrule and nut, fully tightening with a wrench. This method of connection takes much more time than welding, but it is convenient for them to connect polypropylene pipes to radiators.

Compression fittings

Joining a steel pipe with a polypropylene

When installing heating or plumbing, there are areas where metal and plastic joining is required. The connection of a polypropylene pipe and a metal one takes place using special adapters. This fitting has a smooth plastic hole on one side and a threaded metal insert on the other. The polypropylene pipe is connected by welding, and the metal pipe is screwed on with a key. The resulting joint does not have the strength of a welded joint, but it will serve for a long time.

Connection with metal pipe

After complete installation system, it is necessary to conduct a test run of water to check the tightness of all points of connection of pipes and other elements. If threaded connections leaking, they need to be tightened.

Self-installation plumbing or heating from polypropylene pipes is quite a feasible task. To implement it, it is necessary to strictly follow the instructions for using the plastic welding machine and the installation technology. To better understand all the nuances of the process, it is worth watching a video in which experienced installers share their experience.

How to connect a polyethylene pipe with a polypropylene

To connect such pipes, you need to use special fittings. Such a connection is necessary in cases where water was introduced into the house with HDPE pipes, and further distribution of water inside the house is carried out with polypropylene pipes. So, there are 2 types of connections:

In the first case, attach a threaded sleeve to the HDPE pipe, where there will be a clamping connection on one side, and a similar sleeve on the polypropylene pipe, respectively. But there will be a solder joint on one side, and a threaded joint on the other. In both cases, FUM tape or tow is used for the thread to seal the joint and to avoid leaks.
Otherwise, a flange connection is used. Fitted between flanges rubber compressor... The flanges are bolted together.

Polypropylene pipes in the cold water supply system will last 50 years, and in hot water pipelines - at least 25 years. How to connect polypropylene pipes to each other or to a metal pipeline? You will find the answer to these questions in our article. Do not forget that when you are going to make a replacement water pipes hot or cold supply yourself, you must not only choose a docking method, but stock up on the right tool.

Connection methods

Butt welding.
Socket connection.
With fittings.

When choosing a connection method, remember that welded pipelines cannot be dismantled.

Butt welding

To connect pipes with a diameter of more than 50 mm, the butt welding method is used. In this case, a professional welding machine is used.

How to properly connect polypropylene pipes with a diameter of less than 50 mm? A tool is used - a soldering iron for connecting plastic pipes (the so-called "iron").

Technological process for "ironing":

Preparation of pipes - cutting to size, trimming the ends, marking the immersion depth using a marker.
Heating the soldering iron to the soldering temperature - 260-270 o C.
Pipes and connecting parts are put on the soldering iron nozzles strictly perpendicularly.
Time delay for melting.

Warming up parts on a soldering iron

Elements and pipes are removed from the attachments and connected to each other with light squeezing, without twisting. It must be borne in mind that the size of the seam depends on the squeezing force. When brazing small diameter pipes, it is important that the bead does not obstruct the inner pipe passage. Excessive heating should also be avoided, which significantly degrades the quality of the seam.

To "catch" the holding time and the squeezing force, it is necessary to practice on cutting pipes, this will avoid rejects during the main work.

Allow time to cool down.

Socket connection

For joining pipes with a diameter of less than 40 mm, socket soldering is used. For connection, a welding machine with special nozzles and a centering device is used.

Stages of work:

cutting the pipe using special scissors;
cleaning the ends;
heating the device to the desired temperature;
welding (the operation must be performed quickly to avoid deformation);
fixing elements, eliminating mechanical stress.

The quality of each compound should be checked immediately after the exposure to cool.

The socket connection can also be made cold using glue. With this type of connection, it is necessary to make a preliminary "fitting" - check how the pipe enters the fitting. If the entry is too free, the joint will not be airtight, and if it is too tight, the pipe will move the adhesive layer when it enters. When pre-fitting, you need to mark the parts to be connected with a single line.

Performing work step by step:

cut;
stripping;
degreasing with a cleaner;
applying glue (abundantly on the outside of the pipe, on the inside of the connecting element with a thin layer);
connection (the pipe, when inserted into the fitting, turns to uniform distribution glue);
removing excess glue;
exposure time for glue hardening.

Using fittings

Another "cold" method of joining is using fittings. The tool is a crimp wrench that comes with the fittings.

Joining of plastic and metal pipes

You can connect polypropylene pipes to metal pipes using fittings. This type of connection allows you to connect heating devices, water-folding equipment, switch to pipes of other diameters or from other materials.

Fittings types:

press fittings;
crimp;
push fittings.

When working with pipes with a diameter of more than 40 mm, the threaded connection is placed on the metal part of the pipeline.

The connection of polypropylene pipes with metal using special adapters greatly simplifies the work.

Connect metal-plastic pipe with polypropylene can be compression fitting.

After work on the connection of pipes and fittings, it is necessary to check the pipeline for leaks. Water is fed into the system and each connection is checked for leaks. If necessary, the joints are sealed or threaded connections are tightened. In the case of hot water supply, check the system by supplying hot water.