How to start a single-circuit tribute boiler. How to turn on and light up gas boilers of the Danko and Conord models

Thermostats for heating boilers

Thermostats for heating boilers are an important and necessary part in the unit, without which it will be simply impossible to control the boiler. The boiler thermostat makes it possible to significantly save energy, and significantly extend the operating time of the system itself

Inverter generator for gas boiler

An inverter generator for a gas boiler is simply necessary in order to be sure that power outages will in no way affect the operation of expensive equipment. Such generators are a guarantee of the uninterrupted operation of imported boilers, in which an ultra-precise ...

Batteries for UPS for heating boilers

Each boiler must have an uninterruptible power supply, which is a special device (current converter) that converts 12 W from a battery to 220 W. This is the voltage at which all boilers operate. To have an idea of why you need a UPS, you need to know ...

Automatic equipment for heating gas boilers AOGV

Automation for gas heating boilers ensures stable and safe operation of the equipment. These systems greatly simplify the use of heating equipment, increase the efficiency of its work and allow the rational use of energy resources. Automation for gas boilers ...

Question: Boiler Ross AOGV-11, on the street -10, while the gas consumption is about 20 cubic meters / day. Private house 80 sq. M. The boiler stands at 2, the temperature in the house is about 23 degrees. I thought that the expense should be less. Or I'm wrong? Answer: The gas consumption can be checked as follows: set the maximum on the automation, that is, by gas meter count the costs in one minute, then multiply the costs per minute by 60. Check with technical characteristics look at the boiler and see if we fit in or not. Depending on the cost, we either regulate the pressure on the gas valve or not. Question: I have a 16 kW floor-standing Ross boiler. During heating and cooling, a loud knock (click) is heard with a frequency of about 3 seconds, inside at the bottom left, all fasteners are tightened.

How to light a Dani cauldron

If the flame goes out, repeat the operation after at least 1 minute. If the burner does not light up for any reason and the pilot burner goes out, repeat the ignition no earlier than 5 minutes later.
4. Regulation of the temperature of the coolant in the apparatus (boiler) is carried out by turning the temperature adjustment knob to position 1- 7. Position 7 approximately corresponds to a temperature of 90 ° C.

Drawing. Gas valve "HONEYWELL" Sequence of switching on the device (boiler) with gas valve"EUROSIT" Figure. Gas valve "EUROSIT" 1. Open the appliance (boiler) door.

Make sure that the control knob and temperature adjustment (control knob) is in the position (the device (boiler) is off). Open the valve on the gas pipeline in front of the device. 2. Turn the control knob counterclockwise to the piezo ignition position.

Dani heating boilers

Info

Open the appliance (boiler) door. Make sure that the control knob is in the position (the device (boiler) is off). Open the valve on the gas pipeline in front of the device (boiler).

2. Turn the control knob all the way (counterclockwise) to the ignition position and press down, hold it down for 5-10 s (the holding time that is necessary to displace air from the pilot burner tube), and turn further, without releasing the knob, to the middle position (a click should follow). If the pilot burner has lit up, keep the control knob pressed for at least 15 seconds and release it smoothly. Then turn the control knob to the position (device (boiler) on) to ignite the burner, while the flame on the pilot burner must not go out. 3. The pilot burner may not ignite until air is forced out of the pilot tube by gas pressure.

Adjustment of automation in the gas boiler aogv-18 dani comfort

MTS Group) is one of the world's leading manufacturers of water heating and heating equipment, air conditioners and components for domestic and industrial use. ARISTON equipment is specially adapted for Russia; during the development and testing, many factors that have to be encountered in Russian operational practice were taken into account: surges in gas pressure and voltage, low air temperatures, “hardness” of water, areas with high seismic activity, etc.
company

Attention

MTS Group is constantly working to improve its products and reserves the right to make necessary technical changes to its products without prior notice. ATTENTION. In addition to the information provided in this manual, it is imperative to observe the relevant standards, rules, instructions and ordinances that are not listed here.

Gas boiler dani akgv 12 s

Question: Boiler Ross double-circuit 26ntd - E8 jumps out. What does it mean, I can't decipher the error? Answer: The DHW sensor does not work.

Question: Please tell me about the Ross boiler. There is automatic equipment Eurosit 630. The problem is as follows: when the main burner is turned off, it does not completely go out, it burns itself on the sly.

Please tell me is it ok? Answer: Quite normal. The main burner goes out when the set temperature is exceeded. Before this, the bellows covers the burner in order to save and maintain the setpoint. Question: Boiler AOGV Dani.
This article is about how to turn on the Dani boiler with different gas valves. With the arrival of the autumn-winter period, most people are looking for a way to warm up and warm their home. Most of the people use a gas boiler for these purposes. After a long period of not using the boiler or at the first meeting with a gas boiler, many forget or do not know how to start the boiler. Many also do not know what to do if the boiler has gone out or it does not light up at all. And the gas boiler does not ignite, most likely due to the incorrect inclusion of it.

It also happened with us. In our apartment there is Dani's parapet gas boiler. And I decided to give you a little instruction on how to start a Dani gas boiler to help you.

Before turning on the Dani gas boiler, it is necessary to ventilate the room for at least 15 minutes. The sequence of switching on the apparatus (boiler) with the gas valve "HONEYWELL" 1.

Gas boiler tribute instruction manual

Press the control knob all the way and without releasing it, press the piezo ignition button until it clicks. keep the control knob depressed for 5-10 seconds. 4. Release the control knob and check for the presence of flame on the pilot (pilot) burner 5.

If there is no flame, repeat the steps, increasing the time of pressing the control knob. 6. Regulation of the temperature of the coolant in the apparatus (boiler) is carried out by turning the control knob to position 1-7. Position 7 roughly corresponds to a temperature of 90 ° C. The sequence of switching on the apparatus (boiler) with the gas valve "CJSC Mashzavod" ATTENTION! Before firing up the apparatus (boiler), check that the tap of the main burner 1 is closed. Open the door of the apparatus (boiler) and, making sure that the tap 3 in front of the burner is closed, open the tap on the gas pipeline in front of the apparatus (boiler). 2.

Soot constantly appears, it was repeatedly cleaned, everything repeats and the boiler stops working. What to do? Answer: Pull out the burner and rinse it under a high pressure of water from the side of the flame - most likely it is clogged with dust inside, and the gas pressure on the burner is possibly too high.

Well, clean the heat exchanger from soot. Question: Boiler Dani AOGV 7.4. The temperature controller raises the temperature by itself. I bet on 50, next time I come - about 80. The interval between observations is about a month. Everything was fine before. The boiler is 5 years old. What could it be? Answer: What gas valve (temperature controller) is on the unit? He raises the temperature himself - does he mean turning the handle? Or does it not keep the set temperature? If the latter is a gas valve with a thermal bulb and a capillary, then first you need to check the performance of this system itself.
Repair manual, maintenance, technical device, setting up, installing wall-mounted gas boilers Ariston Here, recently came into the hands of a manual for the repair of wall-mounted gas boilers Ariston. tutorial Genus MTS groop. Sorry, the book is paperback. And it was necessary to return it in a couple of days. Therefore, I decided to scan this manual for myself. True, the quality of scanning was disappointing due to the soft binding, but the manual is quite readable. It has over 250 pages. In the internet, I did not find a similar manual for downloading, so I decided to file all the pictures in PDF and put it on a deposit so that everyone could download it. I would like to say a few more words before I link to the file. Still, the file turned out to be not small, almost 100 megabytes, so I decided to give detailed description... The book contains logical schemes for the operation of a gas boiler. principle and device.
ЛЯ`ЙX│7жr? У╝juВО »Д▓% 4╩j'PШ▒╜M╞) X Y┼ @ И▐пP3QЗmж╙н╡HrпT (ОNvyuj ~ СY╪ = VAпTD 4ЦSЄ╗уNХ * ╩хП ╜▄╙ vcaГnяи? Ъ @ u▒hu╦Gzh ┐╠ bK╢мЯlo? √ЎёWПVДЦAHЄ! = ўX1-k╞, gr▓Z╤r F-Gyushi @ ╚ "(b: №ї╒ _ ^ @ И╞88Ре┘ыё @Kh W7фEl ^ Рa█Т├╛F! T╚х1, ї╗ z'bMЇn╬) FKe * zq # Д┌ и╥`╔ 1ь1ьмNttЙn┤╫╫▐ (ЗG┐YИ4√┴Б№╗╨╤░ b! ┤╚└┌Жr╠▄0M () ДЇ) b / ГhМЇ║гФ @ ┬, t┤kу5├└ @ JО% ┌r = ═╚▀ ╞П╥h┘V_Ў╕╤¤a! ▀`╤Ъ▌H3ЦэХ ╔л╧6В╨▌╦зъ6б Юj (mG┤╡ # 4╝Етк╝Д╨tЭБ-, Л█sу╣▌w│NhP% ─ ╢ЁГb╥ЁoЩ8╥ю╪Цш╖gvidНа╥╩чЛf█I╘┼ jМюъBш3шх╛▓_ | ╟ГёЇ╡КW'qEi4 ° o╞В-d Ф┐З = D.╗vus) ╫╫ yTBl $ J ФДР! "бХ╗A! бPZёу4wФun [1 Щg╞A7YЩ! b?) Z│i: Y▓YNL_║GЗ√Э╓FЗеm3╖ФAh; bб╖B; ЛChwnэ╜▒ ": m┼h│ (Д№6.
CONNECTING EXTERNAL CONTROL DEVICES 6.3 MENUS AND BOILER SETTING 6.3.1 Setting: LANGUAGE, CURRENT TIME, DATE 6.3.2 Entering the menu 6.3.3 Menu description 1: PROGRAMMER TIMER SETTING 6.3.4 Menu 2 description: BOILER SETTING 6.3.5 Description menu 3: SOLAR SYSTEM 6.3.6 Description of menu 4: PARAMETERS FOR TEMPERATURE ZONE 1 6.3.7 Description of menu 5: PARAMETERS FOR ZONE 2 6.3.8 Description of menu 7: TESTS AND TEST PROGRAMS 6.3.9 Description of menu 8: PARAMETERS FOR SERVICE SPECIALISTS 6.4 BOILER INFORMATION MENU (INFO) 6.5 BOILER SAFETY SYSTEMS 6.5.1 Fault codes 6.6 LCD DISPLAY OF BOILER OPERATION MODES 6.7 BOILER CONTROL PANEL 6.8 LCD DISPLAY 7 MAINTENANCE SERVICE added MAINTENANCE here to make it easier to search for the file through search engines.
I set the desired temperature. At a given temperature (for example, 60 degrees), the automation (Kare) turns off the device, then when the set temperature drops, the automation restarts it. Periodically (at different times, about once a week), the boiler stops automatically starting up (the temperature has dropped to 17 degrees, and for some reason the boiler did not turn on? maintains the set temperature again until some time.What needs to be checked, cleaned, blown out, changed in order for the boiler to work normally ??? Answer: Check the thermostat Question: Danko boiler, Kare automatics.Sometimes the boiler heats up the water until it boils and goes out And he does not want to switch from the wick to the main torch until you release the tube that goes to the temperature regulator slightly from the reducer.

The boiler operation manual is a set of rules and requirements that are attached in printed form to each model. Despite the variety of gas heating equipment, the principles of use and safety are the same for all models.

The principle of the boiler

Gas heaters can differ in design and technical parameters, but the principle of creating heat in the house is the same - heating the coolant (water / antifreeze) with combustion gas (natural / liquefied). The supply of gaseous fuel to a dwelling is not the easiest and safest thing to do, but consumers are attracted by gas, its comparative cheapness and versatility.

Blue fuel can be used not only for heating, but also for heating domestic water using columns or dual-circuit heater models. Modern equipment is equipped with effective security systems that prevent all possible emergencies. Nevertheless, there are operating rules that are mandatory and are a guarantee of safe operation.

Precautionary measures

Despite the manufacturers' commitment to safety gas appliances, they can still become a source of danger. The Ministry of Emergency Situations regularly reminds the owners of any gas-powered equipment about the precautions:

It is necessary to buy gas-fired appliances from organizations that have an appropriate sales license.
Installation should only be carried out by qualified personnel.
The set should include an instruction manual.
It is forbidden to change the structure of the device in any way.
A technical check must be carried out annually.
It is forbidden to reduce ventilation openings in windows and walls.
In the presence of sealed windows it is necessary to organize the flow of air.
Materials that can quickly ignite must not be stored in the boiler room.
It is forbidden to increase the temperature of the heating medium over 90 ° C.

Accommodation rules

The area of the room in which the heater is installed is at least 7.5 m².
Ceilings - from 2.2 m.
There should be a window that allows air access from the street.
The door should open in the direction of the movement of a person leaving the room.
It is forbidden to equip switches in the boiler room. If they are already installed, they will have to be taken out of the room.
It is necessary to equip supply and exhaust ventilation... For each m³ of consumed fuel - 15 m² of air.
The distance from the heater to elements capable of burning is 25 cm or more. Up to non-combustible elements - 5 cm.From the chimney to combustible parts - 40 cm, to non-combustible - 15 cm.
The device is mounted on a perfectly flat surface, without slopes.

Chimney requirements

Chimney material - steel. It is recommended to use stainless steel.
Cleaning hatches and condensate drainage are required. There should be a pocket at the bottom of the chimney in which deposits accumulate.
Chimney equip external thermal insulation, which is protected from moisture (condensation, precipitation).
Chimney height - from 5 m and at least 2 cm above the outlet.
The chimney is installed on the receiving plate of the vapor trap.
The expansion tank is installed at the highest point in the system.
A safety group and a thermometer are installed on the supply pipeline.
It is undesirable to place the device in openings, niches and other hard-to-reach places.

How to use

V modern models heaters, human involvement is minimized. Before the device is started, it is connected to:

gas pipeline - employees of the gas service;
heating pipes;
water supply - representatives of organizations serving heating systems.

The first start-up is also carried out by service workers. If during connection and maintenance the requirements of the instructions are violated, the warranty will be canceled. The equipment should only be used for the purposes specified by the manufacturer.

During installation, maintenance and repair, original spare parts must be used. If a breakdown or incorrect operation is found, the user should immediately turn off the gas with a valve and call the service or gas service. Produce renovation work on your own is strictly prohibited.

When performing any work on or near the air duct or chimney, it is imperative to turn off the gas. After completing the work, they check the functionality of the chimney and air duct and only then they start starting the device.

How to turn off the boiler correctly

If the device will not be used long time, perform the following actions:

Close the gas valve.
If the equipment is volatile, it is necessary to disconnect the automation and the water pump from the mains.
Shut off the water supply and heating valves.
If the temperature is expected to drop below zero, you will have to drain the water.
Call a specialist to permanently turn off the equipment.

The heater is also turned off for cleaning. Clean it with a damp cloth with a soft detergent and soap. It is forbidden to use aggressive substances.

Safety system

Gas powered appliances need serious monitoring. It is provided either by a person or by an automation system. The latter is capable of providing multi-stage protection that prevents dangerous situations and improves the safety of the equipment. The main task of the protection system is to turn off the device in time by stopping the fuel supply.

Consider the steps of protection using an example floor boiler"Wolf KSO". These modern devices have multi-stage protection. One of the stages is an ionization sensor that monitors the flame. If the fire goes out, a signal will be given to the control unit, it will cut off the fuel supply and prevent an accident.

The combustion chamber has a temperature sensor that monitors the heating of the coolant and does not allow the furnace to burn out quickly. "Wolves" are equipped with a KTD system - chimney draft control. It prevents the build-up of carbon monoxide gases. If there is no draft, the accumulation of combustion products in the chimney begins, the thermostat heats up. When the temperature limit is reached, the thermostat contacts open - the flow of fuel stops.

Automatic protection

Modern heater models are saturated with electronic instrumentation that generates signals for the control unit. Automation, receiving signals from sensors, coordinates the work of all units. The elements that prevent various kinds of malfunctions and problems are safety valves, expansion tanks, air valves, smoke detectors and other devices.

What to do if malfunctions appear

Let's consider situations with breakdowns using the example of Italian boilers. Italian wall and floor heaters are an example of quality and efficiency. But even with proper use, malfunctions may occur that require prompt elimination.

The following problems may appear in Baksi models:

the burner does not ignite;
while working in the firebox, claps are heard;
the boiler has overheated;
the device makes a lot of noise;
the sensor is out of order.

The probable causes of breakdowns are associated both with violations of the operating rules and with reasons beyond the control of the user:

moisture has entered the device;
low quality of the coolant;
decreased pressure in the gas pipeline;
voltage drop in the power grid;
errors were made during installation.

Violation of at least one rule or norm leads to breakdowns, incorrect operation and unnecessary costs.

Frost protection

One of important rules operation of heating systems - ensuring minimum permissible temperature coolant. If water is poured into the system, then at low temperatures freezing occurs, pipes and radiators become unusable. In modern models, this problem is solved - the user is relieved of the need to monitor the coolant.

So, for example, the boilers of the South Korean manufacturer provide reliable protection from freezing. "Navien" is cheaper than European counterparts, but these boilers have all the necessary protection functions, which greatly simplifies use.

When the coolant temperature drops below 10 ° C, it automatically starts circulation pump... If the coolant cools down to 6 ° C, the burner automatically turns on, heating the coolant to 21 ° C.

Ignition instructions

Heaters differ in the type of ignition, so there are nuances when starting different modifications. Before turning on the device, you need to read the ignition instructions in order to do everything right. Let's consider firing up on the example of the Italian boiler "". It is important to check the system for leaks before switching on. For this purpose, the thermostat is turned on to the maximum so that the changeover is automatically triggered. Ariston ignition process:

the appliance is connected to the mains, and the heating regulator is set desired value temperature;
a small noise is heard when the pump is turned on;
when all are eliminated in the pipes air locks, the noise will disappear;
electric ignition is triggered - the boiler turns on independently.

Self-diagnosis

The operation of the heaters is simplified if they have a self-diagnostic function. Almost all European manufacturers have equipped their products with it.

So, for example, German heaters "", displaying error codes on the display, allow the user to quickly understand the cause of the problem and take measures to eliminate it. If code A7 appears on the screen, it is clear that the hot water temperature sensor is faulty.

If A8 is highlighted, the connection to the BUS bus is broken. This feature greatly simplifies the use of gas equipment, makes it easier and more comfortable.

Dangerous situations

The greatest risk is burner malfunction. If the flame goes out, gas can accumulate in the room, which will subsequently cause an explosion. Reasons for extinguishing the fire:

the gas pressure has dropped below the permissible norm;
there is no draft in the chimney;
the supply voltage has disappeared;
the igniter went out.

In an emergency, it is necessary to immediately shut off the fuel supply to the burners - automatically or manually. Modern versions are equipped with automatic devices necessary for prompt shutdown of equipment. The operation of such devices is not only convenient, but also safe.

How to prevent gas build-up in a room

Modern safety standards provide for the installation of gas analyzers in boiler rooms, they are necessary for signaling when gas appears in the room. A special electronic valve reacts to their signals, automatically stopping the flow of fuel to the burners.

What other safety rules are there?

Do not disassemble or disassemble gas devices on one's own.
Handle the power cord with care.
Do not place foreign objects on top of the appliance.
Do not step on the boiler. Do not step on chairs, tables or other unstable objects to clean the wall-mounted kettle.
Watch the coolant, add it to the system in time.
Be careful - in some modifications the use of antifreeze is prohibited.
If you smell gas, immediately turn off the gas, open windows and doors. Exit the boiler room and call the gas service.

Perhaps it is necessary to adjust the main burner, how should it be done, can it be adjusted while the boiler is operating? Answer: Perhaps the knocking occurs due to the thermal expansion of the metal of the heat exchanger. Cracking sound is the result of scale and build-up. Question: Boiler Ross double-circuit 26ntd - E8 jumps out. What does it mean, I can't decipher the error? Answer: The DHW sensor does not work. Question: Please tell me about the Ross boiler. There is automatic equipment Eurosit 630. The problem is as follows: when the main burner is turned off, it does not completely go out, it burns itself on the sly. Please tell me is it ok? Answer: Quite normal. The main burner goes out when the set temperature is exceeded. Before this, the bellows covers the burner in order to save and maintain the setpoint. Question: Boiler AOGV Dani.

How to light a Dani cauldron

This can be done as follows: - Pull the bulb out of the boiler sleeve.

—

Attention

Take two jars of water, an electric boiler for a glass, a thermometer with a maximum temperature of more than 100 C.

— Place the electric boiler for a glass, a thermometer and a thermobalon in one jar of water.
By turning on the boiler and heating the bulb to a certain temperature and then by cooling (for example, pulling it out of a jar of heated water and lowering it into a jar with cold water check (repeatedly) how the gas valve will operate.
—

If it works normally, then you need to check how the contact between the wall of the thermocylinder and the wall of the glass (where it is inserted) is ensured in the boiler.

404 not found

The wick burns, and does not light the main burners, and when it boils, it goes out completely.

Important

Tell me what to do? Answer: The main burners turn off when the specified temperature is reached.

Causes: contamination of the impulse (connecting) tubes between the membrane valve and the thermostat, jamming of the thermostat remote sleeve.

When the water temperature reaches 50-90 C, the boiler turns off completely (everything): adjust the sensor against boiling, there is no draft in the chimney.

Question: As soon as I fully clamp the bushing on the diaphragm valve, the boiler does not ignite, but as soon as I loosen it up a little, it works, and the gas is poisoned a little.

What to do? Answer: Unscrew the screw and remove the handle. Unscrew the screws and remove the scale.

Info

Unscrew the screws and remove the thermostat cover. Remove the diaphragm assembly without damaging the diaphragms.

Remove the assembly using the valve fastening screw. Remove the spacer sleeve.

Adjustment of automation in the gas boiler aogv-18 dani comfort

Press the control knob all the way and without releasing it, press the piezo ignition button until it clicks.
keep the control knob depressed for 5-10 seconds. 4.

Release the control knob and check for the presence of flame on the pilot (pilot) burner 5.

If there is no flame, repeat the steps, increasing the time of pressing the control knob.

6. Regulation of the temperature of the coolant in the apparatus (boiler) is carried out by turning the control knob to position 1-7.
Position 7 roughly corresponds to a temperature of 90 ° C.

The sequence of switching on the apparatus (boiler) with the gas valve "CJSC Mashzavod" ATTENTION! Before lighting the device (boiler), check that the main burner valve is closed 1.

Open the door of the device (boiler) and, making sure that the valve 3 in front of the burner is closed, open the valve on the gas pipeline in front of the device (boiler).
2.

Gas boiler dani akgv 12 s

Question: Boiler Ross AOGV-11, on the street -10, while the gas consumption is about 20 cubic meters / day.
Private house 80 sq. The boiler stands at 2, the temperature in the house is about 23 degrees.

I thought that the expense should be less. Or I'm wrong? Answer: The gas consumption can be checked as follows: set the maximum on the automation, that is, count the costs for one minute on the gas meter, then multiply the costs per minute by 60.

We check with the technical characteristics of the boiler and see if we fit in or not.

Depending on the cost, we either regulate the pressure on the gas valve or not.

Question: I have a 16 kW floor-standing Ross boiler. During heating and cooling, a loud knock (click) is heard with a frequency of about 3 seconds, inside at the bottom left, all fasteners are tightened.

Dani boiler instruction manual

IiQirЖ Y + ╚ & H, Же╛ЕY ^ АЫ (╨н + h, ¤ч ∙ L` L┌╖yУйjO╒╢ЭAR6╖Щф─мъф! 9є╠┼АBpzEPTDEz┬П╬ (┐mgT╞═ИЫў ╝K▀e (tT┤╧dXЄJL░PhX? TXZH »Z┐SHSKMTО (┬хg% ┬╖J ° Рne╤ё8К & ╞Hl┼dпmшХ8ЦSfя╡Sэу╨pX8sBkq4i└ гG · t ° ЦS0с╓ўщД╨Н╬-0uс█ ╥; a = / ╝└t▒u ∙ dггв ° lme╢╓] ЦЦОш'╢я-▀) nTSVZd * ┤зхХ # (L (! Э╔на2╛┬p / и▀┬ + fxМ ° уу╣1кJ╖ ∙ PEEs * k═╒╤hXagШB╙M) ~ ╣wpПYCtl and qн╪4╠╕ (┘┌╗ # СЎ╒hЪ @ ╥ЙD┌╫R▒т; t╔% Сo┼ё # ТЭНЇSюK┘Ъ┬╨╛ ) │оЕ╨гЎ╚Bj & s─┘KACj [▓wt3ЕЎEQ╘YИ╙ & f╦хь + ╥ТЁW╜! Gє (╨eэc╫] ~ 9 | 2b ^ iО% 3n┘╝ъZ = ╜╕д╦Їх3 + ў ┘╜_█Ёёц┘r╣f (° 4 \ 3v╘╘╫TM├╓ыFu▐kagMey╨╧dZI╟╦MЇИ, ъРoаsх = Ї 6 |) [(╡╦7╦╦шЗЇ░Сх: ╧3Нж╚ ЇO╣┼BС ┬ 6▀ »T╥ ∙ bЛР @ ╜ВОЮО & Ё█eвd1┘bIе╠ГЎ╛ Ky╤] + h¤з * ─гPzhr╡Y ($ D * C, L $ YTS, AyUtsivNG # ЁИ─ОH░ єИ─Р▀ж ^ s─ъПрПЙвSжJ ^ ┼ + HVЬЖhlLkцЎ_tUg╨YXр, ╠) / # \ gЦ╡чЛ-hLЮ-╛eoWъ`Z7e8J # MЖb╧, Тєё @ ╤▀Й (* √bPjюUI.BЁ%: р ╢r ° Ў░┬┬╟Ў╖ + 6╢ ^ ╧V№╒PniEC \ m╬Е \ @ Лiodj / ∙ ∙ ЬvЕ + HВб╫ИL│ # ╤9чц.╢▄▓W╢he√) ╦ЙТ╜ ¤╝ъ2эЯ)