The Favorit profile system developed specifically for the Russian market has become, which made it possible to deploy the company's active activities in Russia, satisfying the needs of a discerning Russian buyer.

FAVORIT windows - a new standard of comfort

Concept new system answers the following requirements: plastic windows Thyssen Favorite much warmer than similar systems from three-chamber profiles, withstands all heat loads (including very low temperatures, strong winds and solar radiation), protects against harmful effects ultraviolet and infrared light, it is heat and moisture resistant. In addition, we consider important qualities elegant design, the flawlessness of the components and the profile surfaces, as well as the long service life of the system. and affordability pleasantly surprise buyers.

Although we are supporters of the use of glass with selective coating in insulating glass units, the economic situation in many regions is still such that the use of two-chamber insulating glass units is more justified. When increasing the width air gap a double-glazed window unit by 2 mm in the range from 10 to 15-16 mm gives on average an increase in its resistance to heat transfer by 0.02 m²C / W. As a standard glass unit for the FAVORIT system, the best option with a total thickness of 36 mm.

The system includes elite, and the possibility of using thresholds with a thermal insert.

Regarding the requirements for entrance doors, the new regulations prescribe:

Reduced resistance to heat transfer Ro, m2С / W, entrance doors and doors (without a vestibule) of apartments on the first floors and gates, as well as doors of apartments with unheated staircases, there must be at least 0.6 Rreq product (0.8 Rreq products for entrance doors to single-family houses), where Rreq is the reduced resistance to heat transfer of walls determined by the formula (3); for doors to apartments above the first floor of buildings with heated staircases - not less than 0.55 m2C / W.

Without further details, it is obvious that these are very high thermal engineering requirements! Typical doors on the market made of PVC profiles- these are in the overwhelming majority two-chamber systems with powerful closed steel, which do not fit into the requirements of the norms. The FAVORIT system is an exception. The system includes luxury doors from five-chamber profiles with a width of 71 mm, and the possibility of using. Thus, the resistance to heat transfer will be at least not lower, and when using sandwich panels large area, higher than that of the windows, which will fully comply with the requirements of the standards.

Window scheme Thyssen Favorite:

1. Five air chambers for high thermal protection (class 1 in accordance with GOST 30673).
2. Width 71 mm for optimal temperature distribution in the profiles.
3. Installation of double-glazed windows up to 47 mm wide is possible.
4. Glazing beads with two support legs guarantee reliable glazing.
5. Two planes of the gaskets protect against blow-throughs.
6. Robust steel liners, identical in the frame and sash, ensure the resilience of harsh wind loads.
7. The auxiliary profiles snap into the mounting clips.
8. The hinges are installed through plastic and steel.
9. The drainage of water and ventilation of the folds of the double-glazed windows go through the outer chamber.
10. The axial dimension of the fittings is 13 mm, which increases burglary protection.
11. The 45 ° slope ensures good water drainage and an elegant design.
12. Increased thermal protection thanks to the width of 71 mm and 5 air chambers with a width of at least 5 mm. Heat transfer resistance of the system:

• 0.78 m2С / ВТ (with reinforcing insert)
• 0.82 m2C / W (without reinforcing insert).

Specifications Thyssen Favorite:

Currently, SNiP 23-02-03 has been adopted and put into effect.

THERMAL PROTECTION OF BUILDINGS (ADOPTED AND PUT INTO EFFECT from October 1, 2003 by the decree of the Gosstroy of Russia dated June 26, 2003 No. 113 REPLACE SNiP II-3-79 *). With element-by-element rationing, the principle and long-proven principle has been preserved, where the degree-day of the heating period is taken as the basis. But, despite the fact that the order of the numbers remained the same, and the revolution, as it was with the introduction of amendments to the old SNiP in 1998, did not take place, the required reduced resistance of the windows still changed slightly. Moreover, in different ways: if for the southern regions and Central Russia the value increased by about 0.03 m2C / W, then for cold regions (with degree days above 6000) the figures remained the same. This is due to the fact that it is difficult for economic reasons to improve the design of windows in Siberia and in the northern regions.

Selected direction of development regulatory framework in Russia is in line with general European and world trends. For example, a serious impetus for development building technologies in Europe, EnEV was adopted, the use of which should reduce energy consumption by about 30%. The adoption of EnEV in February 2002 set the stage for the transition in Germany from window sash designs with three chambers and a width of about 60 mm to multi-chamber systems from 70 mm wide. The system also includes a 128 mm wide box.

Being aware of the new standards that are being prepared, simultaneously with their introduction into force in Russia came out with the concept of FAVORIT windows Thyssen Polymer in the group Deceuninck companies... The main principle of the system is that it must be warm and withstand all the harsh climatic loads in Russia. For this, the system must have five air chambers and overall width profiles of 71 mm.

Practice and calculations show that profiles with a width of about 60 mm in terms of increasing thermal protection have exhausted their development potential. The last attempts were ideas to turn 60 mm profiles into four-chambered ones, and to use reinforcing steel with thermal breaks, according to the aluminum principle. But studies and tests in all European laboratories have shown no difference in thermal protection between three- and four-chamber 60mm wide profiles. Only air chambers work and give the effect of thermal protection, in which the thickness of the air gap is at least 5 mm, and in profiles with a width of 60 mm, you can only go along the path of crushing the air chambers into sections 2-4 mm wide. As a result, dies made by all firms for four-chamber 60 mm profiles are gathering dust on wooden shelves in storerooms ... As for steel with thermal inserts, an increase in heat transfer resistance can be obtained, but this solution turned out to be too expensive. Therefore, the FAVORIT system has four heat-insulating chambers with a width of at least 5 mm, and, taking into account the requirements of statics, the size of the fifth, inner chamber for steel was determined. The total required width of the profiles, based on these two considerations, turned out to be 71 mm for the system.

High resistance to heat transfer profile system increases the reduced resistance to heat transfer of windows as a whole. According to the calculated data, for the FAVORIT system with the same double-glazed windows and with a ratio of the glazing area to the product area of ​​0.7, this important indicator increases by 0.03 m2C / W.

This is exactly the amount by which the requirements of the norms increase. For window manufacturers, this means that without changing the design of glass units, but applying a new window system, they will automatically fit into the new norms without increasing the cost of production.

In practice, the resistance to heat transfer is higher than the calculated values. According to tests carried out in the Ural region (SpetsRemStroy LLC) (Test Center Building materials, products and structures of FSUE GRTs KB im. Academician Makeeva V.P.), the following test results were obtained:

• with a glass unit 4M1-12-4M1-12-4M1: 0.66 m2C / W;
• with a glass unit 4M1-12-4M1-12-I4: 0.80 m2С / W;
• with a glass unit 4M1-16-4M1: 0.48 m2С / W;
• with a 4M1-16-I4 double-glazed window: 0.74 m2С / W.

1. Reduction of the edge effect in double-glazed windows, due to the width of the profiles of 71 mm and the height of the pinching of the glass unit of 20 mm. The analysis of the distribution of isotherms in the profiles of the system showed a significant decrease in the edge effect of the glass unit, that is, the formation of condensation along its perimeter.

2. It is possible to install double-glazed windows in the windows with a width of up to 47 mm. Although we are supporters of the use of glass with selective coating in insulating glass units, the economic situation in many regions is still such that the use of two-chamber insulating glass units is more justified. With an increase in the width of the air gap of a double-glazed unit by 2 mm in the range from 10 to 15-16 mm, it gives on average an increase in its resistance to heat transfer by 0.02 m2C / W. The optimal version with a total thickness of 36 mm is adopted as a standard glass unit for the FAVORIT system.

3. The compound (raw mix) is prepared for the use of profiles in the harsh Russian climate.

• The plastic of windows must withstand the most severe frosts, therefore, it contains Special attention toughness modifier. The climate perceptual profile refers to frost-resistant performance ;
• Vicat softening temperature is +89 C;
• Charpy impact strength 44 kJ / m2;
• strength corner joints exceeds the requirements of the norms by two or three times !;
• confirmed durability 50 conventional years of operation (for temperate climate) and 20 - for the northern regions.

4. High static reliability and dimensional stability of the system due to the increased moments of inertia of steel amplifiers and the strength of the PVC profile itself. The moment of inertia of the impost is twice that of other profile systems.

5. The height of the porches: from the outside 8mm, from the inside 9mm. This height of the porches guarantees a secure fit of the sashes to the frame and ample opportunities fittings adjustment. Together with elastic seal special form, it gives high sound insulation and density of windows. At the same time, if necessary, a Regel-Air climatic valve can be installed in the windows.

6. In the constructions of windows of the FAVORIT system, welded seals made of thermoplastic elastomers (TPE) are used gray.The gray color of the gaskets gives the windows a new, elegant design. The stretched seals are welded together with the profiles, which speeds up and simplifies the manufacture of windows.
As for the physical and mechanical properties of seals, they entirely depend on their chemical composition... The formulation used by Thyssen Polymer GmbH makes it possible to use TPE gaskets in the harsh climatic conditions of Russia.

7. The axial size of the fitting of 13 mm increases the anti-burglary qualities of FAVORIT windows.

8. The profiles are elegantly designed with a 45 ° slope and flawless surfaces. technical features, the company made sure that the price of the FAVORIT profile system was competitive in comparison with the currently dominant three-chamber systems with a width of 60m.

The technical characteristics optimized for Russia, together with the availability to the mass consumer, make the FAVORIT system a unique offer on the Russian market.
Excellent technical concept and balanced price policy are prerequisites for the widespread use of FAVORIT PVC windows in municipal and private construction in Russia.

The Thyssen profile is produced by Deceuninck Corporation, an international group of companies whose area of ​​specialization covers the production of the compound, all stages of development and finishing of profiles and PVC systems, as well as the release of products from recycled raw materials. The company is represented in 32 countries, has 18 subsidiaries (production facilities and representative offices). Deceuninck employs 2,700 people, of whom 560 are employed at the headquarters in Bogen (Germany). The key markets for the company's products are North America and Europe. Today Deceuninck is the fifth largest producer of PVC profiles in the USA and Europe.

Thyssen Favorite profile - ideal for Russia

Against the background of a huge variety of products, the pride of the company deserves special attention - the profile system "Favorit" created especially for the Russian market. Thyssen Favorit is a complex system, originally conceived and developed for the harsh Russian climatic conditions. The best German and Russian specialists worked on the creation of this project. FAVORITE windows - structural features

The new window system is significantly warmer than the systems available on the market today, made from profiles of a similar class. It is able to withstand the widest range of thermal loads: extremely low temperatures, strong winds, perfectly resists solar radiation, is characterized by increased moisture resistance and heat resistance.

Additional advantages are elegant design, impeccable selection of high-quality components, as well as profile surfaces, long service life of the system. In addition, having studied the broad color range of this window system, you will be pleasantly surprised by the acceptable cost.

Advantages of the Thyssen Favorite profile

1. Five air chambers designed for increased thermal protection (1st class in accordance with GOST 30673).
2. Width 71mm. Allows you to optimally distribute the temperature inside the profiles.
3. Installation of double-glazed windows with a width of up to 47mm is provided.
4. The glazing beads are equipped with 2 support legs, which provides glazing with increased reliability.
5. Sealing gaskets are located in two planes, which completely eliminates blowing.
6. Heavy-duty steel liners, identical for frame and sash, resist harsh wind loads.
7. The accessory profiles snap securely into the mounting clips.
8. The hinges are installed through steel and plastic.
9. The water outlets, as well as the ventilation of the folds, pass through the outer chamber.
10. The 13mm axial size of the hardware significantly increases burglary protection.
11. The 45 ° tilt does an excellent job of draining water and provides an elegant appearance.

Thyssen Bautec window constructions

This profile system has been specially designed so that it can be used even in the Far North. Regular European windows are about 59-60 millimeters wide, but in this model, the frame and sash have been expanded to 71 mm.

• Only high-quality German-made ROMB fittings are included with the profiles. Each case offers unique additional options.
• "Thyssenite" is a special modifier of impact strength, which was added to the window system for the first time. Even with low temperatures thanks to this material, the structure remains strong.
• From the inside, the porches are 9 mm high, from the outside - 8 mm.
• The “edge effect” of double-glazed units is noticeably reduced due to the height of the glass unit pinching of 20 millimeters and the width of the profiles of 71 millimeters.

Thyssen Zendow

Great combination advanced technologies and high performance characteristics... New development from Deceuninck, which never ceases to delight with its models.

• Excellent moisture drainage and complete protection of fittings due to design features.
• You can always install double-glazed windows up to 41 mm thick. This will provide sound insulation from noise up to 43 dB.
• You can forget about the weather conditions on the street forever, the house will always be warm and cozy.
• There is a multifunctional seal.
• Three or five cameras can be used in the same profile system.
• One of best models in terms of the ratio between price and quality.
• 70 mm - profile width.

Thyssen AD

With a system like AD, you can fully appreciate the benefits of insulating glass units. This is largely due to the affordable price. An excellent option for those who have a very limited budget, even when it comes to necessary acquisitions... The presence of a seal on the frame rebate and in the sash becomes main feature this design.

Besides:

• Steel reinforcements make the structure even more robust.
• The design has high static reliability.
• If necessary, you can easily replace the glass unit.
• Improved precipitation removal and elegant appearance are provided by original design with a 45 degree bevel.
• It is possible to install a double-glazed window up to 39 mm thick.
• Even with temperature extremes, the structure does not collapse, because a special nylon thread strengthens the sealing rubber from the outside.
• The sealing rubbers themselves can last up to 30 years.
• The service life of the window is about 40 years.

Plastic windows Thyssen (Deceunink)

Thyssen windows, produced by the Belgian company Deceuninck, which bought this brand in 2005, are distinguished by their excellent design, excellent heat and sound insulation characteristics, due to which they deservedly belong to the premium class products, we strongly recommend installing them in cases where strict requirements for soundproofing and energy saving. This is especially true in cases where heating costs are a burden on the owner of the premises.
Put reliable windows much cheaper than spending extra fuel heating the environment. The Deceuninck company is engaged in the production of window profiles Thyssen, already under her brand, opened a profile production plant in Protvino, Moscow region. Thyssen (Deceuninck) products have found wide application and respect from customers. At the moment in Russia, two types of profile are widely known from Deceunink products, they are both of the seventieth series: Favorite five-chamber profile with a gray seal and Bautek three-chamber analogue of Favorite with a black seal. The most popular are windows:

from Thyssen Favorite profile

When choosing windows for your home, you should pay attention to the TISSEN FAVORIT windows. This product has been developed for areas with very low temperatures or in buildings where there is an increased requirement for energy efficiency.

The THYSSEN FAVORIT profile has improved thermal insulation characteristics, the profile width is 71 mm, the profile has a flawless white appearance, 5-chamber structure. In the THYSSEN FAVORIT profile, you can install a double-glazed window up to forty-seven millimeters wide. Optimum thermal insulation will be achieved when using a 40 mm glass unit.

The composition of the raw materials from which the profile is made is tested at low temperatures. Plastic must withstand without deformation very coldy, therefore, in its composition, special attention is paid to impact toughness. The THYSSEN FAVORITE profile is a Premium class profile.

In terms of price, design quality, it has no equal.

The THYSSEN FAVORITE profile uses a special light gray seal made of a special material. This sealant is the Deceuninck know-how. According to the test results, the service life of the seals of this system is 30 years. In addition to the sealant in Thyssen, there are other know-hows: anti-break glazing bead, a special system of linings in the glass unit so that the sashes do not sag, plastic mount imposts.

Below, you can see the structure of the profile

Thyssen "Favorite"

Natalya Sergeevna

I want to thank the guys from the Ramokna company for an excellent and quality work... Thanks to the measurer Pavel for guiding the price and choosing the windows for us, I also want to thank the guys from the OT team, Oleg and Viktor, they did everything quickly and efficiently. Everyone is very polite and pleasant. Thanks. Happy New Year! Good luck and prosperity!

Boris Stepanovich, Moscow

I would like to thank the RamOkna company for the quality work done. I got new windows installed yesterday. The AS team worked. I would especially like to note the work of the installer Alexander (unfortunately I do not know the name), as well as the measurer Sergei, who initially made a professional calculation. As a result, everything came up and performed with excellent marks.

Irina Khimki

Moved to new apartment, the windows seem to be not bad, but they were blowing pretty hard. I decided to change it right away, without waiting for winter. According to the reviews, I liked the company Ramokna, people praise it. I made an order, the measurer arrived on the same day, and after another 5 days, the guys Igor and Alexey had already made the installation. I liked everything very much, for the quality and service I give a solid five!

Lyudmila Vasilievna

Today the installation was carried out on Shipilovskaya street. I liked everything very much, from the measurer Oleg to the installers Fedor and Alexander, the team is very qualified, they installed everything on time. I express my deep gratitude to the whole team. 12/08/17

Astakhovs Maxim and Olga

We would like to express our gratitude to the installer Fyodor Georgievich, the installation was carried out on 09/27/14 (in Lyublino). A very neat person, he does everything with love. The installation was done with high quality! We are going to order another window, and of course we will ask Fyodor Georgievich to install the window. He swept the trash behind him, removed it, took everything out! There would be more people like that!

Thyssen profile is produced by the company Deceuninck... Deceuninck is an international group of companies specializing in the compounding, design, development, extrusion, finishing of PVC systems and profiles and the production of recycled products. The company operates in 32 countries, has 18 subsidiaries(production and / or representative office), has 2,700 employees, 560 of whom work in the main plant. The company has Thyssen Polymer(a subsidiary of Deceuninck) three factories: one, the main one in Bogen (Southern Germany), and two others in the USA. The four most important markets for the company are Germany, North America, Central, Eastern and Southern Europe. Today the company occupies fifth place in Europe and in the USA for the production of PVC profiles.

Profile Thyssen Favorite. Profile design Thyssen Favorit

The pride of the Deckenink-Thyssen Polymer company was the profile system Favorit, developed specifically for the Russian market, which allowed the company to expand its activities in Russia, satisfying the needs of a discerning Russian buyer.

Plastic windows Thyssen Favorit- this is complex system, originally conceived and developed specifically for Russia with its harsh climatic conditions, is a joint product of German and Russian specialists.

Five air chambers for high thermal protection (class 1 in accordance with GOST 30673). Width 71 mm for optimal temperature distribution in the profiles. Installation of double-glazed windows up to 47 mm wide is possible. Glazing beads with two support legs guarantee reliable glazing. Two planes of the gaskets protect against blow-throughs. Robust steel liners, identical in the frame and sash, ensure the resilience of harsh wind loads. The auxiliary profiles snap into the mounting clips. The hinges are installed through plastic and steel. The drainage of water and ventilation of the folds of the double-glazed windows go through the outer chamber. The axial dimension of the fittings is 13 mm, which increases burglary protection. The 45 ° slope ensures good water drainage and an elegant design.

Why do plastic windows from the Thyssen Favorit profile provide a high level of comfort?

• The room is warm in winter and cool in summer.


• Thermal comfort not only in the room, but also near the window.


• The height of the porch increased to 9 mm prevents the penetration of dust and noise into the room.


• Easy to clean due to the absence of condensation.


• The geometry of the profile makes it easy to remove dust from the groove for the glazing bead.


• Possibility of installing a Regel-Air climatic valve to improve the microclimate.


• The plastic mullion connector excludes freezing at the junction, unlike metal connectors, and the strength of such a connection is higher than a standard metal one.

How do PVC windows from the Thyssen Favorit profile differ from their analogues?

1. Increased thermal protection due to the width of 71 mm and 5 air chambers with a width of at least 5 mm.

The high heat transfer resistance of the profile system increases the reduced heat transfer resistance of windows as a whole. According to the calculated data, for the FAVORIT system with the same double-glazed windows and with a ratio of the glazing area to the product area of ​​0.7, this important indicator increases by 0.03 m2С / W.

2. Reduction of the "edge effect" of double-glazed windows, due to the width of the profiles of 71 mm and the height of the clamping of the double-glazed window 20 mm.

The analysis of the distribution of isotherms in the profiles of the system showed a significant decrease in the "edge effect" of the glass unit, that is, the formation of condensate along its perimeter.

3. It is possible to install double-glazed windows in windows up to 47 mm wide.

Although we are supporters of the use of glass with selective coating in insulating glass units, the economic situation in many regions is still such that the use of two-chamber insulating glass units is more justified. With an increase in the width of the air gap of a double-glazed unit by 2 mm in the range from 10 to 15-16 mm, it gives on average an increase in its resistance to heat transfer by 0.02 m2C / W. The optimal version with a total thickness of 36 mm is adopted as a standard glass unit for the FAVORIT system.

4. The system includes elite doors from five-chamber profiles with a width of 71 mm, and the possibility of using thresholds with a thermal insert.

Thus, the resistance to heat transfer of entrance doors from FAVORIT profiles will be at least not lower, and when using large-area sandwich panels, higher than that of windows, which will fully comply with the requirements of standards.

5. The compound (raw mix) is prepared for the use of profiles in the harsh Russian climate.

The plastic of windows must withstand the most severe frosts, therefore, special attention is paid to the modifier for impact strength in its composition. The climate perceptual profile refers to "Frost-resistant performance";

· Vicat softening temperature is +89 С;

· Impact strength according to Charpy 44 kJ / m2;

· The strength of corner joints exceeds the requirements of the norms two to three times !;

· Confirmed durability 50 conventional years of operation(for a temperate climate) and 20 for the northern regions.

6. High static reliability and dimensional stability of the system due to the increased moments of inertia of steel reinforcements and the strength of the PVC profile itself.

The moment of inertia of the impost is twice as high as that of other specialized systems.

7. Height of the vestibules: outside 8mm, inside 9mm.

Such a height of the rebates guarantees a secure fit of the sashes to the frame and wide possibilities for adjusting the fittings. Together with an elastic seal of a special shape, this gives high sound insulation and tightness of the windows. At the same time, if necessary, a climatic valve "Regel-Air" can be installed in the windows.

8. In the constructions of windows of the FAVORIT system, welded seals made of gray thermoplastic elastomers (TPE) are used.

The gray color of the gaskets gives the windows a new, elegant design. The stretched seals are welded together with the profiles, which speeds up and simplifies the manufacture of windows.

9. The axial dimension of the fitting of 13 mm increases the anti-burglary qualities of FAVORIT windows.

10. The profiles are elegantly designed with a 45 ° slope and flawless surfaces.

Along with all the above technical features, the company made sure that the price of the profile system "FAVORIT" was competitive in comparison with the currently dominant three-chamber systems 60m wide.

The technical characteristics optimized for Russia, together with the availability to the mass consumer, make the FAVORIT system a unique offer on the Russian market.

An excellent technical concept and a balanced pricing policy are prerequisites for the widespread use of FAVORIT PVC windows in municipal and private construction in Russia.