Wooden heat-saving windows. Heat-saving glass

One of the important factors of energy saving in the room is the right glazing, since a lot of heat may be lost through the windows, and a significant share of losses falls on infrared radiation. Reduce the convective heat loss through the window, by increasing the number of glasses and cameras in the package and installing a warm separation frame, and infrared radiation can be kept indoors due to heat-reflecting glass coating.

If sufficient thermal insulation is not provided in the edge zones of double-glazed windows, the window freezes, it is covered by it, through it the room leaves warm air, and inside penetrates cold. When used in the design of double-glazes of traditional aluminum dividing frames, such a problem is observed quite often.

Frames made of stainless steel improve the thermal properties of the glass package. But the best heat insulating properties have the so-called warm framework of the Warm EDGE system, for the manufacture of fiberglass, plastic, silicone and similar polymeric materials.

Read about other types of distance frames.

Warm framework is durable and does not lose performance characteristics Under the influence of sun rays, no moisture is afraid. The thermal conductivity of the warm framework is significantly lower than aluminum, therefore, heat insulating characteristics above. In practice, double-glazed windows with a warm frame ( warm edge) have such advantages over windows with an aluminum separation frame:

• in winter time 5-6% increase the temperature of the edge zones of the window;
• preventing the formation of condensate, mold, in winter - Inea;
• none in the design design, vulnerable to cold penetration from outside;
• heat losses are reduced through the window, the recoil coefficient of heat into the room reaches 70%.

Heat-reflecting glass package

Even a single-chamber package of two glasses is well kept warm in the room, if the glass is applied. It is almost transparent, permeable for rays of the visible spectrum (the transmission rate of the energy-saving windows with a heat transfer coating is only 4-5% lower than the usual).

Essence of the heat transfer (low-emission) coating in the election bandwidth. Solar energy (shortwave) it passes well inside the room, and long-wavelength energy released by heaters and resulting as a result of the conversion of solar, delays indoors. Heat losses are reduced, cold zones disappear in the area of \u200b\u200bthe window, the effect of drafts is eliminated, the probability of condensate formation is reduced, since the glass is well warmed.

Even in the USSR, the technology of applying a three-layer coating was developed: the reflective layer is located between the buffer and protective. For reflective, silver, silver and copper are used, and for buffer and protective - aluminum, tin, titanium. The coating on this technology is applied to the purified glass by spraying in vacuo, the spraying can be arc or magnetron. Today, heat-reflecting coatings are divided into "soft" and "tough", or and-glass and to-glass.

• The technology of applying a soft coating is easier, the cathode spraying method is used in vacuo, a two-layer coating, a silver layer directly to reflect infrared rays, and the titanium oxide layer is protective.
• The rigid coating is applied by pyrolysis by directly in the process of producing glass, at the moment when it is rolled and has not yet cooled. The feature of the K-glass is that the metal particles penetrate the crystal structure of the glass, the metallized heat transfer film is covered with thin protective layer Glass.

Adhesion and stability to damage to the hard coating are higher, but the actual heat transfer characteristics are better at the soft coating, and it lies more evenly. In addition, its technology is preferable in terms of environmental impact. The rigid heat-reflecting coating today is lost popularity, since the process of its application is very laborious, which affects the cost of such glasses and double-glazed windows with them. And glass is more affordable by price, but less durable, the coating is characterized by low chemical resistance.

The properties of the heat-saving film allow energy-saving windows in winter Save heat indoors and reduce its heating costs. In the summer, they prevent overheating of the room, creating a comfortable and favorable microclimate in it.

Double-glazed windows with heat transfer coating are more expensive than normal, but more economical due to the possibility of reduced the number of cameras when choosing a glass package and saving on heating after installation. This technology allows you to do with a smaller number of windows - a single-chamber double-glazed glass with heat-reflecting glass by heat insulating characteristics is superior to a two-chamber without spraying. it perfect solution For conditions that do not allow using massive double-glazed windows and solve the heat saving problem by increasing the thickness of the glass and the number of cameras.

There is another technology of manufacturing energy-saving windows until he received widespread Due to high cost, but characterized by exceptional energy efficiency. This is the so-called electric-heated double-glazed glass of tempered to-glass with conductive tracks, it connects to the power supply and is used as heating element. Such double-glazed windows can be installed in unheated rooms.

Sliding warm glazing

On balconies and loggias, and the verandas often use sliding glazing, which allows the maximum rational use of the existing area. The frames do not break off, and shift relative to each other. Such glazing can be cold (aluminum) and warm (using a plastic profile). If the glazed room is planned to sculpt and use as a residential, do not do without, although it is more expensive.

Sliding systems based on aluminum profile Also may have a thermal master, such systems can be used for warm glazing and are not inferior to the energy efficiency of plastic glass packages.

One of best decisions for warm sliding glazing - pVC system Slidors (Sladors). These systems are made from PVC profile with galvanized reinforcement inside, in double-glazed windows, a double seal with a special insertion is used. Double-glazed windows combine high strength with excellent heat and sound insulation characteristics, waterproof, due to the high rail can be used in any weather. By price sliding systems Based on the PVC profile is more accessible than swinging.

For warm sliding glazing, you can apply the PREMILINE CVE system under the condition of the installation of energy-saving double-glazed windows. LG Hausys system with double 18 mm thick glass packages are also used for warm sliding glazing.

Panoramic warm glazing

Well, that he passes into the room maximum light. On the other hand, an increase in the glazing area can lead to a growing heat loss in winter. Therefore, it is important to use for warm panoramic glazing Not single glasses, and double-glazed windows, with the best heat insulating characteristics. For these purposes, it is worth choosing double glazed windows with filling chambers with argon, low-emission coating of glass and a warm separating frame.

For warm panoramic glazing, not massive PVC packets, and smaller windows based on an aluminum profile with a plastic thermal master can be preferable. The constructs of Sunflex (Germany) are ideal, this is a folding system that allows you to glazate the openings of different configurations up to 3.5 m high, to carry out non-free glazing. The design is distinguished by low thermal conductivity and high noise insulating properties, each sash has a double seal contour. The system can be aluminum or wood-aluminum, has aesthetic attractiveness.

The heat-saving characteristics of the window depend on a number of parameters - thickness and quantity of glasses, chamber thickness, and filling them, the material of the separation frame, the presence of heat transfer coating and the technology of applied. Increases the heat-saving properties of the window Filling cameras argon, the use of a polymer separation frame, low-emission spraying on the glass. The most effective windows in which several heat-saving parameters are combined.

For the manufacture of energy efficient windows in the company "Isolux" manufacturers can order CLIMAGUARD ® heat-saving windows with a thickness of 4 mm with a protective layer based on silver, as well as packages with and glass 4 and 6 mm. Both those and others are filled with argon.

Advantages of heat-saving glass windows

Strength and reliabilityWindow systems with heat-shielding double-glazed windows are easier and smoothed out accessories, extending its service life. Low-emission spraying is maintained throughout the system operation time.

Effective heat protection in winterThe design isolates heat much better than standard, although less weighs. A package with one camera of two energy-efficient glasses is 1.5 times easier typical and saves in a room by 25% more heat.

Comfortable microclimate in summerIN summer heat Packages reflect thermal waves out and maintain a pleasant coolness in the room.

Heat indoors provide two sources. First - solar radiationentering the windows outside - ultraviolet, visible light and short IR waves; The second is heated objects and heating devices in the room from which long IR waves proceed. Prevent heat loss help Low-emission coating and low-emissionreflecting infrared radiation into the room. Glass with ion coating is mounted first so that the spraying is located inside the glass package. Silver ions on the surface of the heat efficient package create a mirror effect. In contact with thermal waves from heating devices, they direct radiation back. As a result, the intensity of heating can be reduced to 50%.

Energy PackakesClimaguard ®.SOLAR Multifunctional. They solve two tasks: in winter, they hold warm in the room and protect the room from the sun. One layer of their coating reflects heat waves from the heated surfaces into the room, the other - holds to 60% solar energy. Silver spraying does not violate the transparency and optical properties of glass, helps save on heat supply, eliminates fogging windows.

Application and price for heat saving double-glazed windows

We offer affordable high quality design. All of them are certified and meet the requirements of GOST. Teplopackets are popular in glazing:

• cottages,
• urban apartments,
• trade and business centers,
• medical institutions.

The cost of such products depends on the selection of their modification - with and-glass or multifunctional Climaguard ®, from glass filling area, glass thickness. The energy-saving glass package quickly pays off - it saves up to 40% more heat in comparison with the standard analogue.

That ended the summer, it's time for the heat, and at the same time the fall and preparation for heating season. Very soon the batteries, as well as electrograms and gas heating devices that consume hot water, gas and electricity in large quantities. In connection with this situation, the question arises related to the decrease in premises heating costs, and one of the most practical and cheap solutions is the replacement of conventional windows to heat saving. Saving energy and finance when using these windows is obvious: when using heat exchange with external environment reduced by 70%What leads to a similar reduction in heat loss, and, of course, your money!

Stis glass windas - winner of the Award "Take care of Energy"

What is heat-saving windows?

What is heat-saving windows? it ordinary windows With special windows in the composition of double-glazed windows, covered with a very thin layer of metal, which practically does not miss warmly through itself - that is, in winter it will be warm in the apartment, and in the summer - cool, while ordinary glasses are practically delayed. Also a serious advantage of this type of windows is that it prevents the burnout of furniture, wallpaper and carpets, that is, over time, from behind the Sun, they will not lose their color and brightness! Window data also varies by types of coating: a solid coating used in single glazing without double-glazed windows (for example, with glazing balconies, loggias, etc.), and a soft coating that is universal in essence, because it is characterized by higher thermal insulation parameters and Used only in the composition of the glass package.

GlassComposite profile + double-glazed windows: the perfect formula of the warm window

Also, one of the most significant advantages of heat-saving windows can be attributed to the fact that they are much easier and stronger than their glass analogues, which not only facilitates their use, but also significantly increases durability through the use of alloys and composites in them.

Thus, the advantages of energy-saving double-glazed windows are obvious, and if you have a desire to get the optimal combination of price and quality - you can safely order them and calmly meet the heating season.

As one of optimal options From the point of view of the listed performance characteristics, a universal window system can be called the STIS ™ heatpapers, which, with a competent configuration of options, are ideal for all regions of Russia in any climatic conditions.

Our company, at the request of the customer, will install such double glazed windows like in warm sliding doorsand in any swing structures.

Premium German brand in the Russian market since 1995. With us you get present German quality from the company with a 48-year history worldwide.

• EVERYTHING profile systems top class "A"
• All are filled with frost-resistant and marked with the letter "M"
• All have the maximum 4-sided steel reinforcement
• Unified quality standard, regardless of the country of production

The more aircases, the smaller the air exchange and, respectively, above thermal insulation.

The wider profile and more mounting depth, the higher the heat insulation.

Profiles only of the highest class "A"

According to the thickness of the inner walls, all our profiles are higher class "A" - the thickness of their facial wall is at least 3 mm.

• class "A": Face wall at least 3.0 mm
• class "B": front wall of at least 2.5 mm
• class "C": wall thickness is not normalized

Please note that 80-90% of the Russian market are the classes "B" and "C" and only 10-20% of the class A profiles. At the same time in our assortment Veka profiles Only class "A".

We fundamentally use the profile systems of classes "B" and "C" (with a width of the front wall less than 3.0 mm).

Only frost-resistant profiles

According to GOST 30673-99 "PVC profiles for window and door blocks" for climatic resistance, all our profiles are "frost-resistant" - for areas with an average monthly air temperature in January below minus 20 ° C.

GOST standards for different classes:

• normal performance "H": average temperature In January - minus 20 ° C and above
• frost-resistant execution "M": The average temperature in January is lower than minus 20 ° C

In our assortment only frost-resistant specialized systems marked with the letter "M".

The heat transfer resistance (thermal heat resistance) is the main thermal insulation coefficient. It is determined by the ratio of the temperature difference outside and indoors to the heat flux passing through the window. The higher this number, the better the effectiveness of thermal insulation.

Evolutionary windows SmartGlass 2.0

Our multifunction glass windows work on you and in winter, and in summer. In winter, the spraying of silver particles retains up to 90% of the heat of the heating devices, and in the summer the double-glazed windows reflects 25% more solar heat than ordinary plastic windows.

• 42% more heat in winter (energy-saving properties)
• 25% less heat in summer (sunscreens)

All our double-glazed windows contain special energy-efficient glass. We do not use conventional glasses even in the most basic equipment.

Climate Management Systems AIRDRIVE I, II and III

The windows are built into the optimal mechanisms of ventilation - the sash are opened by 1-5 mm depending on the selected mode. These are not external devices (comb or valves), namely embedded accessories.

Three options:

• AIRDRIVE I: Slotted ventilation (1 mode)
• AIRDRIVE II: Discrete multistage ventilation (3 modes)
• AIRDRIVE III: Discrete multistage ventilation (5 modes)

We try not to put the ridges because of their external view (Only at your desire). Valves in principle do not use due to the fact that they violate the integrity of the window, reduce its tightness and strength (since profile and reinforcement is drilled).

The comfort and heat in the house depends on the quality of window structures. Many people want to buy windows in Moscow, having high heat protection rates that are well transmitting sunlight inside the room.

Constructions with I-glass have a number of advantages:

• reduce heating costs;
• prevent the burnout of interior items;
• improve the thermal insulation of the room;
• do not accumulate on inner side condensate;
• have a long service life.

It is necessary to know that the price of heat-saving windows in Moscow is available to everyone. Designs with I-glass are not much different at cost from conventional plastic models.

Examples of calculating cost

Bivalve.

Profile: Kbe Etalon. 58 mm.

Cost * with a discount of 29% 8 190 rubles.

Three-rigid.

Profile: KBE Etalon 58 mm.

Filling: two-chamber glass windows 4-10-4-10-4Irs (thickness 32 mm).

The outer glass is covered with low-emission energy-saving spraying based on silver ions.

Cost * at a discount of 29% 11 960 rubles.

Balcony block.

Profile: KBE Etalon 58 mm.

Filling: two-chamber glass windows 4-10-4-10-4Irs (thickness 32 mm).

The outer glass is covered with low-emission energy-saving spraying based on silver ions.

Cost * with a discount of 29% 14 700 rubles.

* The cost is followed by the product: excluding delivery and installation work.

Advantages of the order in the "Star window"

The company offers energy-saving plastic windows for any premises. The company has extensive experience, offers customers only high-quality products made according to individual measurements.

Another advantage is that we ourselves produce plastic windows saving heat. All materials used are characterized by high wear resistance, safety for human health.

Ordering from us window systems With energy-saving glass packages, you do not have to wait long. The manufacture of structures will take at least a time, the work will be executed within the specified time.

How we are working?

Customers know that the cost of our products offered is available. Collaboration with the client begins at the stage of measurement. You can call the measurer for free and calculate the cost.

After performing measurements, our company employees perform such actions:

• clarify the wishes of customers;
• systems are design;
• manufactures structures;
• deliver them to the object.

Profile and glass designs match high qualityAnd their installation is engaged in real professionals.