What to glue an inflatable mattress Bestway. We repair useful things: how to make an inflatable mattress at home, and what glue to use

The popularity of inflatable furniture is due to the convenience of its use and compact sizes in folded. It can be used both in tourist trips and at home, as an additional bedroom. The active operation of the product often leads to the appearance of holes through which the air leaves, so the owners are often wondering how to make an inflatable mattress.

We put the mattress with glue (click to enlarge)

Violation of the integrity of the product from PVC is not a reason to throw it away. Typically, the sales centers of branded inflatable furniture provide services for the repair of their goods. Specialists know how to restore the product. However, choosing where to make an inflatable mattress, it is necessary to take into account that this is a costly service.

Why air leaves

Index products can be blown away for various reasons. It does not always blame for that puncture or gap. The source of the problem may be valve. Perhaps the garbage accumulated in the groove does not allow you to spin the lid enough tightly, in this case, rinse enough enough. The broken plug can be replaced.

Acute items or claws of pets can leave cuts on the fabric of the product. From improper operation, the seams are diverged and the inner partitions of the inflatable mattress are broken.

Methods for detection of defect

To repair the product, you need to find the place of damage. Often the holes have minor sizes that are almost impossible to notice. There are several methods with which you can detect a break:

• the product can be immersed in water. The hole will detect itself with a shading of small air bubbles;
• at home, the break site can be found using a foamed soap solution, which is applied to the surface of the mattress. Big bubble sides above the break site;
• several liters of the foam solution are poured inside the influted product. Outping the mattress, it can be detected from defects with a quiet whistle liquid flows;
• the surface of the air filled mattress is recommended to sprinkle with flour or any powdered product. The air flowing out from the opening will blow down the powder. After detection, the mattress is cleaned with a vacuum cleaner;

From the video you can learn more:

IMPORTANT! Usually, damage appear at once a few pieces. Faster all the inflatable mattresses are torn the area of \u200b\u200bthe relief pattern.

The detected defect should be marked with a marker or marker.

Need to localize the place (click to enlarge)

Repair of an inflatable product

Choosing how to flip inflatable mattress Intex., It is necessary, if possible, use a corporate set for repair, which is sold complete with a product. Manufacturers are equipped with a set of velor pages, special glue and vinyl film. How to make a mattress, described in detail in the instructions. She is attached to the set.

If the set is lost or used, it is possible to flick the mattress in other ways. You can proceed to the rope process only when the product is dry. It is important to choose correctly, what glue to use for these purposes. It is better to use the adhesive agent on a rubber basis or another composition, which after drying saves plasticity. By gluing a superclaim, the owner risks irretrievably spoil his thing.

Usually, the approach to repair changes, based on the location of the damage location.

Elimination of punctures and cuts

The question is how to make an inflatable mattress, is solved easily. The patch can be cut out of the rubberized thing or use the latch from Remkomplekt for tires.

On the smooth side of the product area around the hole is sufficiently deguted with acetone or alcohol. The same means the patch is processed. For mattresses they are cut without corners. The glue is applied on both surfaces that are tightly pressed to each other. Place of repair is placed under the press for 12 hours.

If the mattress is damaged from the velor side, the pile from the surface around the hole should be considered fine-grained emery paper. Next is glued with the latch in the described method. Defect on velor with this repair can not be avoided.

Check the video to learn more:

You can take an inflatable mattress from the wrong side, then on the surface the place of the puncture will be almost unnoticed. To do this, the defect area needs to be pulled out through the product for an inflation. The patch is fixed with glue. After half a day, the product can be turned out and filled with air. Reflecting on how to make an inflatable mattress, we must take into account a number of advantages of the last way: the break site is effectively disguised, the patch is kept from the inside more reliable, since the air puts the air to which the bed is filled. Although the repair process is more laborious.

Failure to comply with the rules of operation of the product leads to the fact that the consumer is often forced to look for an answer to the question of how to make an inflatable mattress on the seam. The defect of the joints to eliminate it is quite difficult enough. The patch, put on the seam from the wrong side, will not last long. Manufacturers recommend calling for help in service center.

Tip! An insulating tape can be used as a temporary means of eliminating punctures. A missed mattress can be used for several days.

Inflatable furniture is simple and easy to use. Thanks to such products, you can provide full-fledged bedrooms for guests, and the rest in nature is more comfortable. Careful use and compliance with operation techniques can save from the need to look for an answer, how to make an inflatable mattress at home.

Over time, inflatable accessories for recreation and tourism lose their strength, and this happens for various reasons: due to puncture, cracks, negligent circulation. How to make an inflatable mattress to bring him the practicality and extend the service life? Read about the selection of glue, the rapid detection of the defect, the rules of repair, as well as useful advice In handling inflatable mattresses.

How to detect damage

Inflatable mattress is a universal thing both in hike and in everyday life. He is indispensable in the tent, on the beach, as a spare bed for guests. Mattresses are made of fine material, thanks to which the object weighs little and is easily transported. For the same reason, the product does not differ in high strength: they are easy to pierce with a stone, a branch or simply break, the mattress will not stand in front of the animal claws.

The cause of damage on the inflatable mattress can be an excessive pumping air. Due to the voltage on the surface, microcracks appear, more often - in places of seams and other connections.

If the mattress is quickly blown away, then you need to look for damage. You can detect a hole in several ways:

1. Inflate the mattress completely. Turn off all noise sources and listen. If there is a hole, she will give himself a whistling sound. To determine the exact location, take the hand near the sound source. You will feel a thin and cold air flow. To find it faster, wet the palm with water.
2. Immerse the mattress in the water: air bubbles will go in the place of puncture. In this way, it is easier to find the location of the defect, but it does not differ convenience for home conditions, since the volumetric mattress cannot be placed in a bath or pelvis. Work on the detection of bubbles in water is recommended to be carried out in the pool or reservoir.
3. Another way: Beat the water with a detergent in soap foam, jump out it with a tassel or sponge and apply a thick layer on the surface of the inflatable mattress. The product should be tightly pumped, otherwise the method does not work. If the puncture is there, it will start bubble. In the case when the approximate place of damage is known, you can apply for shaving foam.
4. If the mattress has a lurisal surface, then the soap solution will be badly foaming. For such surfaces there is a dry method: covered with starch, flour, or something powdery and easy. Together with the air, the powder layer will be blown away.

After the damage is detected, circle it with a chalk or marker so as not to lose. Do not forget to completely dry the mattress before fixing it.

Preparation of the surface and patchwork

Repair of inflatable mattresses are made only on a dry and compressed surface. If you neglect by this rule, the quality of the repair will leave much to be desired. First of all, the product is well dried, then cleaned from dust and dirt. The next stage is degreasing. The mattress in the place of damage is wiped with gasoline, alcohol or acetone. If there is a flock on the product (such a coating forms the upper side of the known Intex mattresses), then the pile is removed. This can be made fine-grained emery paper or acetone.

Mattress manufacturers have provided possible damage. There are special sets for repair, which include a patch, glue. They can be bought immediately with an inflatable mattress. The advantage of such a repair kit is that the patchwork material corresponds to the source.

If the repair kit is not, then a piece of rubber is suitable for repairing automotive or cycling chambers. Material can serve both a children's rubber toy. The patch is cut for 2-3 cm. Wider damage. The form is round or oval. Before fixing the mattress, the patch is also cleaned and degreased for better clutch.

What glue to use

In the assortment of glue is easy to get lost. What makeup to choose to repair? Recommended universal adhesives, Products for pVC gluing, as well as rubber varieties. The glue must meet the following requirements:

• water resistance, because the mattress will be used in water bodies;
• strength, since the product is subject to loads;
• elasticity - glue must correspond to the material that is filled with air.

Than you can pack the mattress inflatable:

• glue "Moment Universal": gluits almost all materials in various combinations;
• polyurethane can be consolidated to repair an inflatable mattress, as it creates a solid, elastic and waterproof layer;
• From the natural rubber forms elastic seams and does not leave stains, but requires reinforced pressed parts.

Tip! The glue "super moment" or "second" (and other cyanacrylate compositions) can also attach a patch, but they do not differ elasticity after drying, as well as some compositions can damage the product fabric. Therefore, such adhesives are not recommended.

Mattress repair

Repair is to impose a patchwork for damage. For a smooth side, this method is applied:

1. The prolque place should be circled with a marker. This area is slightly cleaned and degreased by a solvent.
2. Cut the patch out suitable material, preferably without acute corners. So the mount will be more reliable.
3. Apply a small amount of glue using a brushes on a cleaning patch and leave an average of 10 minutes. Exact time Search in instructions for glue. Do the same with the place where the patch will be attached.
4. Connect the plot with a place of damage and hold a few minutes.
5. You can leave details under the press.
6. Full drying of the adhesive occurs on average after a day.
7. It is recommended to use the product after 2-3 days, not earlier.
8. If there are several damage, then it is necessary to repair the mattress in stages, waiting for the complete drying of each patch.
9. If after sticking the air still leaves the mattress, look for other damage. Or check whether the valve is firmly closed.
10. If malfunctions in the valve, then you need to unscrew and wrap.

Tip! No need to apply a thick layer of glue, enough one or two drops.

How to repair the mattress Intex.:

1. If the defects showed up from the velor side, then before work you need to clean the pile. Flock coating is treated with alcohol or solvent.
2. Now you need to cut extra villi to the width of the patch. This is done with a sandpaper (shallow emery paper). If this is not done, the glue will not connect the patch and velor. You can skip the coating with a knife. The main thing is that the blade is blunt.
3. The resulting Piglet is better to handle again with acetone, so that the perfectly smooth surface is turned out.
4. Now you can cover the purified glue zone.
5. Further, all actions are similar to the method described above: to connect the plug by glue, hold a few minutes or leave under the press, wait for drying.

The darous products will not be repaired unnoticed. When attaching a patch, the "lisks" will remain. But there is interesting method: If the mattress design allows, repair it from the inside. To do this, remove the damaged part - push it through the pump hole. Actions on the imposition of patchwork are no different from the external method of fixing. Such a repair will be as inconspicuous, as well as durable, because it presss the air from the inside.

1. Compositions for gluing inflatable products flammable. Do not conduct repair work Near the sources of fire. Do not inhale glue pairs, work in a protective mask in a ventilated room.
2. If you doubt the reliability of gluing with your own hands, the workshop will always come to the rescue. There you can repair the discharges of the seams, damage to the internal partitions, the valve defects, the breaks of more than 5 cm. Such defects are eliminated using special equipment.
3. The renovated thing is stored only in a blown state. If it is used on water, then after carefully drying.
4. For cleaning does not apply aggressive and abrasive detergents.
5. Inexpensive products are not intended for a wide range of use. So, inflatable beds are not used on water bodies.
6. If the mattress is rubber, then the glue for its repair is selected rubber. More often, the mattresses are made from polyvinyl chloride (PVC).

Consider the mattress with your own hands is easy. You only need to detect all holes, pick up the right glue or simply use the items for the repair that were included with the mattress. Despite the simplicity of repair, still it is necessary to treat inflatable products extremely gently, not to place them on the surface with large and sharp particles, do not pump the air, to store correctly.

If you discovered a hole on velor, on a flower surface, first of all, you need to remove these villi from the zone adjacent to the hole. Around the hole should be cleared a small area of \u200b\u200bthe size of a little more than five-supported coins.

To remove a flocked coating, velor, pile, it is necessary to moisten with a solvent or a tool for removing the nail polish and wait for 1-2 minutes. The adhesive mix of the pile with an inflatable mattress will soften a little and then the whole layer can be easily considered a blunt knife or spoon.

Formed harsh, once again rub the solvent and remove the remnants of the adhesive basis vellar coating. After drying, we apply glue, we wait, we apply a latch, press. For details about the right gluing, see below ...

1. Rate damage and prepare a place to repair an inflatable mattress. Gently straighten the affected cylinder site on a flat surface. If there is no such, then put the board under the cut.

2. Remove the glue and tape of transparent material from the repair kit.

3. Clean the place of gluing from dirt and degrease it with a 646 solvent. You can also use acetone, or at worst, in field conditions - alcohol. I do not advise to clean the material with emery paper - it can only harm it.

4. Verify the piping on the cut and draw the place of the gluing a pencil or handle

5. Cut the patch from the material strips desired size included in the repair kit. The patch can be any form, but better if it is round or oval. In the field, you can simply cut the corners from the rectangular billet. Diameter or maximum length Patchworks must be 3-5 cm length Core.

5. Singing the contents of the glue tube to the place of damage. With the help of a tassel uniform, thin layer apply glue on both bonded surfaces. Give adhesion to dry.

6. After 10 - 15 minutes, repeat the same procedure and leave the glue again.

7. After 5 minutes, you can begin actually the gluing itself. Five minutes - conditional time. It depends on temperature ambient, glue storage time, and even from humidity. Touch the glue - it should dry, but stick slightly.

8. For the "activation" of glue, the gluing site and the patch must be heated. To do this, you can use the hair dryer for drying. Remember that the place of the gluing must be heated, and not to light! It is necessary to carry out this operation, it is necessary enough that glue during this time is not drying.

9. Now the glued surfaces must be applied one to another.so that the air bubbles do not remain under the patch and pushing it well and roll the solid roller. If there is no one at hand, you can use any techniques: knife handle, can, spoon, etc.

10. Not bending material at the place of gluing, gently fold the mattress (boat) and leave to dry at least one day.

Watch the video how to stack a bed with repair kit Intex:

Many will be interested to know how the Intex mattress is rushing at home to extend the operational period.

After all, inflatable furniture is not only convenient for relaxing in nature, but also is sharply necessary when the house is unexpectedly filled with guests.

The most important thing, inflatable furniture is characterized by compactness - it can be easily folded if necessary and hide in the closet.

But keep in low temperatures Such a product is not recommended, since a similar environment will adversely affect its surface shell.

How to detect punctures in inflatable furniture?

Before starting the repair of the spoiled inflatable Intex mattress, it is necessary to carefully examine it on the presence of punctures, the number of which will be able to identify after certain manipulations.

Since inflatable furniture (mattresses are no exception), it is most often torn on the butt seams, then to look for damages, starting with their inspection.

Typically, such mattresses lose their tightness due to severe pumping, which is prohibited by the instructions.

In this case, the gap often occurs between the horizontal plane of the canvas and the inner edge.

Other causes of damage to the INTEX product may be cuts or punctures, whose culprits become animals - amateurs can be quiet or torture claws.

If independently at home failed to identify damage, you will have to seek help to the master.

The most complex areas of the inflatable mattress that need to be repaired is considered to be the discrepancy between the seam and the coupling of the inner edge - with such a problem it is unlikely to cope at home, so best output Will give the mattress for repairs in the workshop.

By the way, to make an Intex inflatable mattress, you need to contact the service center of the company, in which this product was purchased.

If the firm is solid, then it goes towards its customers, i.e. it can carry out the repair of the product at home, which is most often suitable for the owners. If the puncture is small, then you can make an intex inflatable mattress at home.

To detect punctures in the canvas of an inflatable mattress, various ways are used.

If the product had small size, It would be possible to inflate and omit in the bathroom filled with water, which would allow to see how air leaves the punctors.

But since such a product is large, and in parts, it makes no sense in parts, it is better to use another, not less effective method Detecting punctures:

• we take any detergent, but it should be good in a foam;
• foam we apply to the sections of the mattress web, where damage is suspected;
• we investigate the processed canvas for the presence of bubbles that will say that air leaves the mattress in this place.

If the specified method did not bring results, you can apply another way to identify punctures, but it is more troublesome.

In a fully liberated mattress, the mattress needs to pour soapy water - there will be five liters enough. Then it is necessary to pump up the product again.

When turning into an inflatable mattress from punctures with air, water will be punched. There will be such places to circle with a marker, freeing the mattress from the water, and before the ripping, carefully dry.

How to independently repair the inflatable mattress?

After the punctures in the inflatable product managed to detect, they need to be stuck, impoverished on the damaged space of the lat.

But if it was damaged to the seam on the product, then only professionals with special equipment will be able to fully repair it.

You can try to renovate butkovo Sow. Inflatable mattress and at home.

The seam discrepancy site is carefully treated with alcohol, which will help not only clean, but also to degrease the lobby layer of the web, then, following the instructions, it will remain to impose a patch and take a damaged place.

In this case, there is no guarantee that such a repair will allow for a long time to operate the product.

The fact is that the seams of the mattress when sticking will interfere, as a result of which the patch can not be firmly pressing to their surface.

Given this factor and the fact that the patch will spoil the attractiveness of inflatable furniture intex, it is better to try to repair damaged seams from the inside:

• the spoiled section of the mattress must be turned through the hole for the valve, which can be done using the usual line and hands;
• the surface to be repaired should be dry and clean. In order to degrease it, it is wiped with alcohol;
• using a patch suitable sizeneed to miss it inner side glue, with the adhesive substance should not be much, as this will reduce the quality of work;
• the glue-treated patch is pressed tightly to the damaged portion of the web;
• after 12 hours, the repaired product is turned off, and after installing the valve, the place is inflated.

In order to improve the quality of the work done, the missed section of the mattress is recommended to be put under the press.

Since the rowing is performed using a substance containing dangerous components (methyl, acetone, polyurethane tires), then the repair of the product is not possible in the residential room. After using glue, it is necessary to wash your hands.

It happens that all punctures are stuck, and the mattress does not hold air. In this case, it is recommended to pay attention to the tightness of the product valve, which is a weak place of all types of inflatable furniture.

In order to repair the valve, the valve is removed, the place of its adjoining to the canvas is grinding in fine skin, then treated with silicone lubrication, after which the valve is returned to its place.

How to store and use an inflatable product?

The rules for storing inflatable furniture suggest that the mattress is better to save in a nasty form. In this case, the product should be dry and clean.

Therefore, if it was used to relax in nature, it needs to be thoroughly washed and dried. For washing the cloth, it is recommended to use a weak soap solution.

It is unacceptable to use detergents containing abrasive inclusions or chemically active ingredients.

With their help, you can quickly clean the mattress, but they will significantly reduce the duration of its operation, negatively affecting the strength of the canvas.

Inflatable mattresses are manufactured for various purposes, they have a different quality that respectively affects the cost.

Some people, wanting to save, acquire cheap products for the purpose of using them are not intended.

For example, take a mattress for swimming with you, to sleep on it. As a result, the goal does not justify the funds spent, since the mattress in the process of operation will quickly deteriorate.

If the mattress began to gradually drop the air and there is no confidence that it will be repaired at home so that the product does not lose former look, it is better to attribute it to the repair shop.

The master, knowing his business and having the necessary equipment at hand, will be able to solve the problem in a short time.

With new technologies, all available punctures and weak seams of an inflatable mattress will be detected and repaired without losing a aesthetic appearance.

Do not do independent repair Mattress, if its damage exceeds 5 mm or there is a problem with internal partitions.

Such damage to fix at home is almost impossible, while in a specialist workshop will be able to assess the existing damage and, if necessary, restore the product by replacing the sections of the old web to the new one.

Do not think that the workshop does not take place repairing mattresses with large breaks of seams or surfaces.