How to make a wooden scabbard. How to make a sheath for a knife from leather or wood with your own hands How to make a sheath from a wooden insert

Every outdoor enthusiast or just a supporter will certainly have a favorite camping knife. And everyone, probably, is familiar with wrapping it in paper, a newspaper, a towel, etc., from which it will certainly jump out on the way and ruin your favorite bag.

Well, if you have a special branded knife, which always comes with a sheath, even if you got it without a sheath, you can pick it up in stores for the expedition. But what if you have the most ordinary, simple, but favorite knife? The way out in this situation will be to make a sheath for a knife with your own hands.

How to sew a knife sheath with your own hands?

Before proceeding with the manufacture of a knife sheath, let's pay attention to one point - the handle of the knife must certainly be impregnated with water-repellent substances.

So, in order to make a scabbard with your own hands, here's what we need:

cotton dense fabric impregnated with resin;
a piece of hard dense quality leather;
kapron thread with a strong needle;
stationery clips;
an awl and pliers, if possible a drill with a thin drill;
calipers;
sharp working knife;
sharp cutters;
strong wire;
high-quality shoe polish for polishing scabbards.

Now we can get to work.

DIY leather sheath:

First of all, we will make a hard liner from cotton fabric. We form it on the blade of the knife itself, after covering it with paraffin.

Next, we cut out a suitable piece of leather, moisten it well, then put the insert on the knife and place it in the center of the cut.

Then we wrap the knife with a piece of skin and fix it with clamps along the contour of the future seam, leave the product until the skin is completely dry.

Returning to work, we remove our clamps.

Now we begin to sew homemade scabbards. Using an awl, make a couple of holes at the beginning of the fold line. We pass the thread on both sides and get the first stitch.

In the opposite direction through the same holes we make the second stitch.

Using the awl, we make markings for the following holes, strictly monitoring the uniformity of their location.
Next, take a drill with a thin drill and make holes.

And we continue to sew the sheath into two needles, removing the needles with pliers.
Thus we sew to the end of the line. Now we tightly tighten the nylon thread in the way as shown in the figures.
Next, cut the ends of the threads and melt them over a candle or match. The most difficult part of making a knife sheath with your own hands is over.

Now take a sharp knife and cut off the excess skin, leaving a small margin.

Then, with the help of an abrasive skin, we process the cut.

Now let's look at how to make a hanger for a scabbard with your own hands. Cut out a U-shaped blank from a skin flap, cut small holes at the top with a knife.

We pass the "tails" through the upper holes.

For further work it is better to remove the knife from the sheath and insert a wooden stick right size. Mark the holes for mounting the suspension.

Using cutters, we make holes along the outlined contours.

And, finally, we will pass the finished suspension into the holes made, focusing on the images.

Now our do-it-yourself leather scabbard is ready. In conclusion, let's do a couple more strokes.
Next, we have to fit the scabbard under Exact size scabbard. So, we insert the knife into the sheath, after wetting them well, and tighten it tightly with wire.
We are waiting for the complete drying of the skin and remove the wire.

In conclusion, we will process our homemade sheaths with shoe cream, so that they will become softer and transform. At the same time, we insert the knife into the sheath, wrapping it with polyethylene.

Now do-it-yourself leather scabbard is ready! Have a fun active holiday.

The sheath is a sheath that protects the knife from any damage and saves its owner from the danger of an accidental cut. Many lovers of hiking, hunting or fishing, as a rule, have several of these things at once. Some of them try to make a knife sheath with their own hands. Although this is a long process, it allows you to make an exclusive and very useful accessory.

Before you make a sheath for a knife with your own hands, you need to choose the right materials and tools. It is on their quality that practicality and attractiveness will depend. appearance finished product.

Another important factor in the success of creating a sheath is strict adherence to the entire sequence of actions and taking into account the advice of people who are professionally involved in the manufacture of this accessory. They will help beginners not only avoid most mistakes, but also make the most beautiful and practical thing. Professionals advise the following:

Manufacturing options

As a rule, all high-quality knives are made of Damascus steel, so they need a strong and reliable sheath. This is necessary not only for your own safety, but also to maintain the cutting object in proper condition. In most cases, a hand-made leather knife case meets all these requirements, so you can prepare all the necessary items and feel free to start working.

In the manufacturing process, a minimum amount of inexpensive and accessible to everyone materials will be used, which can be easily found in stores for fishermen and hunters. All this allows you to make such scabbards even for people with modest financial capabilities.

Leather for a hunting knife

Today, many ways have been invented to make a scabbard out of leather with your own hands. All of them are quite simple, but require accuracy and the ability to work with this material. Beginners need to be extremely careful and not miss even the most small parts process. In order to make high-quality leather scabbard for a hunting knife , it is necessary to prepare such materials and tools:

If you could not find any item from the list, then it can be replaced by any suitable analogue. From this, the quality and appearance of the finished product will not change. The process of making a leather scabbard is simple and consists of the following steps:

In the same way, you can make a leather case for an ax with your own hands. The whole process is carried out in the same steps. The only differences are the size and shape of the leather blank.

For a camping knife

All lovers of outdoor activities cannot do without such an important item as a camping knife. It will help not only cut various objects and food, but also come in handy in other more extreme conditions. To protect it from damage, you need to make a holster for a knife . For this you will need:

When preparing the listed materials, it is important to find each of them. This will make it possible to completely immerse yourself in the workflow and not be distracted by the search for a particular item. Sheaths are made in compliance with the following sequence of actions:

Using the same technology, you can make a scabbard for a sword or dagger. This work is not easy, but with the right approach, it can be done.

simple case

This scabbard making option is one of the simplest, so it is ideal for beginners. Ready product is very strong and reliable . To sew it, you need to take:

In the process of work, you will also need hot water, so you need to choose a suitable pan in advance and boil the liquid. Just warm it up a bit before use. Step-by-step instruction:

Sheaths are a must for any quality knife. With their help, the product is not only protected from mechanical damage, but also becomes safer. At proper manufacture and following all the recommendations of professionals, you can make a unique thing that will appeal not only to you, but also to all your friends. Don't be afraid to experiment and add your own. One day you will succeed and make not just a scabbard, but a real masterpiece.

A hunter cannot do without a good knife. A large selection of models is presented in stores, and some prefer to make this item of equipment on their own. In any case, every knife must have a good sheath. They will securely fix the blade in the stowed position, protect it from dirt and moisture, and prevent injury. Scabbards can be made at home with your own hands. The first point that needs to be decided is what to make this piece of equipment from. Durable scabbards can be made from leather, plastic, plywood, or birch bark.

Making Scandinavian type scabbards from leather

To make a leather scabbard with your own hands, you need to take:

hard skin about 4 mm thick;
shoe knife;
knurling with a wheel for marking seams;
kapron thread;
awl;
a strong needle that can be used to sew leather;
pliers;
wood cutter with a semicircular notch.

First of all, you need to put a knife on a piece of skin and outline the contours of the sheath blank. At the same time, 3 cm must be retreated from the edge of the blade on the sides, and an allowance of 1 cm must be left below the tip. In the upper part, the workpiece must be cut under the handle.

You need to make a markup for two blanks, and then cut them out. For this, it is best to use a shoe knife. It must be held at an angle of 45 degrees, so that in the end the two blanks of the scabbard are connected evenly. If desired, the skin can be made thinner - for this it is enough to scrape off or cut off the inner layer.

Then the skin should be soaked for 15 minutes under warm running water. After that, it becomes soft and pliable, and it can be easily wrapped around the blade. After that, you need to mark the future seams. For this, it is best to use the knurling. Thanks to its use, the seams will turn out to be as even as possible, the thread pitch will be the same throughout. After that, you need to make holes in the sheath with an awl. They should come out through the end cut of the skin, located at an angle of 45 degrees.

In order for the scabbard to be strong and durable, they must be sewn with a thread first on one side, and then skip it again in the opposite direction. After that, the seam must be fixed with knots. Thus, the main part of the scabbard will be ready.

It remains only to add a suspension to the blade case. To do this, you need to make a hole in the sheath with a wood cutter with a semicircular notch. If not, you can use a sharply sharpened metal tube.

To make a pendant, you need to use a strip of leather. At one end it is necessary to make a cutout in the form of a pitchfork 3 cm long and a third of the strip wide, and then prepare the corresponding holes in the sheath, thread the suspension through them and form it. A rivet can be added to the tip of the scabbard.

When making sheaths for Scandinavian-style knives, such as Swedish, Finca or Puuko, a latch is not necessary. Such knives are placed almost completely in the case and hold well in them.

Finished leather scabbards can be dyed. Another option is to polish them with a semi-abrasive wax paste, which will give the product dark shade. Paint and wax applied to the skin will perfectly protect it from moisture. If you want to preserve the natural color of the leather, it can be coated with shoe wax.

Plastic scabbard

Another option is to make a knife sheath out of plastic. sewer pipe. In addition to this, you will need:

saw;
building hair dryer;
vise;
drill or screwdriver;
rivets;
riveter;
ready-made fasteners for fixing the scabbard on the belt or leather for its manufacture.

First you need to saw off a piece of pipe, which should be slightly longer than the blade. Then you need to make a longitudinal cut in it along the entire length. After that, the workpiece must be well heated and squeezed so that it becomes flat. To do this, use a building hair dryer at a temperature of 300 to 500 degrees.

Having warmed up the workpiece well, you need to insert a knife inside and squeeze it, giving it the desired shape. To do this, it is better to clamp the plastic in a vise. When the form is ready, you need to cut off all the excess, giving the workpiece the shape of a blade, leaving an allowance of about 2 cm in the area of the blade.

Then you need to drill holes in the plastic and insert rivets into them. At the same time, it is necessary not to press too hard so that they do not push through the material. Studs from rivets are most conveniently sawn off with a drill.

Finished scabbard can be painted black regular paint from a balloon. It remains only with the help of riveting to attach a latch for fastening on a belt - and the sheath for a hunting knife is ready.

Plywood scabbard

To make such a sheath for a hunting knife, you will need:

layered plywood 1.5 mm thick;
a piece of thick felt;
epoxy resin and hardener for it;
leather belt;
lavsan thread;
file;
sandpaper.

From plywood, you need to cut two blanks in the shape of a knife. They should be slightly larger than the blade itself. It is also necessary to cut out two pieces of felt that match the shape and size of the plywood plates. They need to be glued to the plywood with epoxy.

Both blanks must be folded to each other with felt inside and a leather belt glued to them so that a loop is obtained. It will be used to attach the knife to your belt.

Then the blanks must be coated with epoxy resin from the outside and wrapped with lavsan threads. After the epoxy dries, you need to repeat the procedure. Thus, it is better to apply at least 4 layers of thread so that the sheath is strong and durable.

When epoxy is under last layer the thread will dry, the scabbard needs to be given finished form using a file and sandpaper. You can smooth their corners or apply various grooves and embossments to their surface. To give the product a more presentable look, it will not be superfluous to perform other finishing. To do this, the scabbard can be painted or wrapped with braid.

How to make a scabbard out of birch bark?

You can also make a sheath for a knife with your own hands from birch bark. This is a material that has been tested for centuries. It is especially well suited for making a case with wooden handle, as it will be harmoniously combined with it. To make such a sheath, in addition to birch bark, you will need:

scissors or a knife for cutting material;
wide saucepan;
board 10 mm thick;
a small piece of skin about 2 mm thick;
food film;
insulating tape;
stationery clips.

The first step is to cut three identical blanks from birch bark. They should be shield-shaped with a pointed bottom edge. In the manufacture of the scabbard, the blanks will need to be folded in half and wrapped around the blade, laying them one on top of the other. Then you need to cut out two spacers from a pine plank curved shape, which will be located in front of the cutting edge of the knife.

Birch bark should be placed in boiling water and boiled for 2 hours, and then turn off the heat and leave to soak for a few more hours. After that, she will curl up into a tube. While the birch bark is being cooked, you need to attach a spacer made from a plank to the blade with electrical tape.

It is better to wrap the knife with cling film beforehand. There should be a small distance between the spacer and the knife. To leave it, you need to place a piece of thin skin in front of the cutting edge.

Then you need to get a piece of birch bark out of the water, carefully unfold it and wrap it around the knife, securing it in the area of the cutting edge with clerical clips. After 10 minutes, when the material takes the form of a blade, you need to remove the clamps and put another piece of birch bark on top. Then the procedure must be repeated a third time. After that, leaving the clamps, the birch bark should be allowed to dry for an hour.

Then the future sheath must be smeared moisture resistant glue PVA between layers of birch bark and fasten again with clips. A day later, the entire structure must be disassembled by separating the spacer from the plank from the blade. Next, you need to generously lubricate the PVA spacers, clamp with their help in a vice the part of the sheath located in the region of the cutting edge of the knife, and leave for two weeks.

After that, you need to drill holes in the sheath and sew them with a thick thread or a thin strap. You also need to do oval hole under the belt clip. To make it, you can use a rope or a braid woven from leather strips.

With high-quality scabbards made from improvised materials, a hunting knife will last as long as possible. Which of the manufacturing options to choose is a matter of taste. Any sheath will be good if you approach their manufacture correctly.

Every survivalist, outdoor enthusiast, fishing, hunting or just tourism has a favorite working knife. It's good if the knife comes with a good shop sheath that meets the requirements for them. And what about those who either bought it, but without a sheath, or the sheath turned out to be a "Chinese" fiction ... Of course - to make a sheath for your favorite knife with your own hands. How to make a scabbard from or from I already wrote, it's time to tell you how to make simple handmade leather scabbard.

Let me point out right away that step-by-step instruction belongs to Viktor Vlasenko. (vlasenko.ru)
Notes or before proceeding with the manufacture of the scabbard:
1. The handle of the knife must be impregnated with a water-repellent compound (the handle must not be afraid of moisture).
2. To make a leather scabbard with your own hands, you need a hard liner. Alternatively, it can be made from cotton fabric impregnated with epoxy resin, molded directly on a knife blade, coated with molten stearin or paraffin with a brush. To protect the wooden handle from epoxy resin you can wrap it all, including the bolster, with masking tape (painting tape is impregnated with wax). We cut off the protruding masking tape along the outer edge of the bolster ... We check that the adhesive tape fits snugly on the bolster (without gaps that epoxy could get into). Next, we cover the blade and the area of masking tape near the bolster melted in a "water bath" with paraffin or stearin. Next, we wrap it with a cotton cloth soaked in epoxy resin ... The material is “soaked” in epoxy in strips and wound around the knife blade. Instead of cotton fabric, you can use a medical bandage, gauze, but in this case the liner will turn out to be more fragile. After the polymerization of the epoxy resin, the liner blank is boiled in boiling water to free it from stearin and mechanically processed to the required outer dimension. A hole is made in the liner from the end to drain moisture and, if desired, several holes on the sides to facilitate drying of the skin ...

We believe that we have already made the insert, selected a suitable piece of leather and are ready to start making the scabbard ...

Soak the skin blank for 1 - 2 minutes in warm water. After we place the knife with the insert on the center of the workpiece. (If you feel sorry for a piece of wood or a blade, you can wrap them in polyethylene).

We wrap a knife with an insert with wet skin and, using clerical clips, fix the skin from the side of the future seam.

We leave our design in a warm place until the skin is completely dry ...

After the skin dries, we get a molded leather sheath blank with which you can already work comfortably ...

Let's start sewing! We will sew with two needles. For sewing, we need an awl, a pair of needles, pliers and threads.

We make a couple of holes at the end of the future scabbard. We thread the thread into the second hole and make the first tie towards the end of the scabbard ...

We make the second screed into the old hole, but in the opposite direction ...

We do the markings for the screeds slowly with the help of an ordinary ballpoint pen and any "measurement standard" ...

After marking with an awl, we outline the exact position of the future hole ...

For ease of stitching, the holes marked with an awl are additionally drilled with a drill ...

The seam is performed using two needles ... First, insert one needle with the end of the thread into the prepared hole ...

Using pliers, we pull the needle through the hole ...

Now we insert a second needle into the same hole, but on the other side ...

Continuing in this way we reach the last hole in our seam.

Here, before tightening the threads, we make several turns of one thread relative to the other.

After tightening, this "coil" will be inside the hole ...

We make one or two screeds with "layers" in the opposite direction ...

We bring the threads to the "back side" of our scabbard, cut them with a small margin and melt ...
We did the most laborious part and as a result we got an almost finished scabbard ...

We take a sharp knife in our hands and cut off everything superfluous ...

Armed with an abrasive skin, we bring the edge of the scabbard to the final dimensions ...

Now it is the turn of making a suspension of homemade leather sheaths.

Cut out a U-shaped suspension blank from a strip of leather

We thread two "tails" of the suspension into pre-prepared holes at its end ...

We take out the knife from the sheath, insert a technological wooden insert instead of it, and on the back of the sheath we mark the places for the holes for attaching the suspension ...

With sharp cutters we cut out the marked holes for attaching the suspension ...

Wood cutters are sold in many hardware stores, you can make your own ...

We insert the "tails" of the suspension into the extreme holes ...

We stretch "to the stop" the "tails" of the suspension ...

We make a wire loop and with its help we capture the "tail" of the suspension ...

With a wire we pull out the "tail" of the suspension into the central hole ...

We do the same with the second "tail" of the suspension ...

We cut the "tails" of the suspension to the size we need and insert them into the remaining free holes ...

As a result, we got the gimbal mount only on the skin without the use of all kinds of rivets and other "foreign" parts...

Our scabbard has acquired a completely finished look ...

Although the sheaths made by us can already be used for storing and carrying a knife, but now we need to do a number of additional operations to more accurately "fit" their size to a specific knife. First of all, this applies to the mouth of the scabbard. So let's get started ... Stock up on scraps of thick copper or aluminum wire.
We will soak the sheath sewn by us in warm water for several minutes ... Insert a knife into the wet sheath and use a wire to pull the skin at the edge of the mouth. In order not to deform the edge of the skin in the area of the seam along the latter, we will lay solid protective pads from improvised material. If you want to give the sheath some "artistic" they can be pulled together with wire in several more places ...

Leave the sheath in this state until the skin is completely dry. When the skin dries, it stretches and the inner surface of the sheath will exactly repeat the shape of the knife handle...

After the skin dries and the wire ties are removed, we get a ready-made, but not yet impregnated sheath ... If desired, before impregnation, home-made leather sheaths can be decorated with artistic ornaments using different technologies from surface carving to embossing with painting…

Let's stop at simple version scabbard without additional decorations. For a water-repellent impregnation of the scabbard, we need a wax-based shoe polish. It is better to use "KIWI" in a suitable color, but you can soak the skin with any product containing wax or paraffin, although in the case of the latter, the sheath will turn out to be hard ... Using shoe cream will not only protect the sheath from moisture, but also make the skin soft, which contributes to a more tender and dense fit of the scabbard in the area of the knife handle. To exclude staining of the wood of the knife handle during the impregnation of the skin, the knife is placed in a plastic bag ...

We insert the knife in polyethylene into the sheath and begin to apply the cream on the skin of the sheath ...

After applying a layer of cream on the surface of the skin, let it soak in, then apply it again, let it soak in again ... After a while, rub the sheath with a cloth to a shine ...
If, when wiping the surface of the skin with a clean cloth, it does not stain, then we consider that the entire cream has been absorbed and can be removed. protective film from the knife ... It is also useful to additionally impregnate the skin of the sheath from the inside in the area of \u200b\u200btheir mouth ...

The treatment of the sheath suspension with cream also helps to increase its elasticity ...

It remains only to be happy for us, as we made comfortable, reliable and beautiful scabbards for our favorite camping knife with our own hands.

PySy:
1. After piercing the holes, a groove can be cut along the entire seam so that the thread is recessed into the skin, but this is most likely for aesthetes. Firstly, this seam in such a sheath lies in a recess and access to it is limited (that is, if you run your finger along the seam, you simply won’t feel it, and secondly, when stitching with a nylon thread with a good tightness in unwaxed leather, the thread itself cuts quite well into the skin and does not require additional protection ... Then, when soaking, the skin swells and finally hides the seam ...
2. To protect the threads from cutting, you can use an additional leather spacer along the seam. If you put a normal insert under the blade, then there is no need for a strip of leather under the seam - this is superfluous, because. threads are cut mainly in the area of location cutting edge blade in the sheath, and cutting the threads in the area of the hilt - this still needs to be tried ...
If you make a scabbard without an insert, then a strip of leather saves the thread from cutting through and its use is justified, but with long blades and soft skin often the skin itself is cut on the side in the region of the blade, when the knife is sharp and it is inserted into the sheath with a certain turn of the RK relative to the seam ... The conclusion is unambiguous - for soft sheaths, it is necessary to make a hard liner ... Well, as for the leather spacer - this is optional ... If the sheaths are made without an insert, then the use of a leather spacer to protect the seam from cutting is a necessary attribute.

If you are the proud owner of a license to carry a knife, a sheath is a must for you. If you don't have them, you can make them yourself.

How to make a sheath for a hunting knife?

Usually Hunter knives made of Damascus steel, so the scabbard must be reliable and strong.

First you need to make a sketch on paper. To do this, lay the knife on paper and outline its contours with a pencil.

Then fold the sheet along back side drawing and cut out the layout along the contour. This is what the end result will be.

Now take a piece of leather and attach a knife blank to it, while the sheath will fit exactly in size. On the skin, draw the same product, only with a margin of one centimeter on each side. What kind of leather can be used? On the this example a chrome-tanned saddlecloth three millimeters thick was used.

Don't forget that you also have to cut out a two and a half centimeter wide hanger and a one centimeter wide insert.

The suspension must be made seamless. With any available tool, make holes in it as shown in the figure below.

Cut off the excess and thread the straps through the holes.

In a piece of a knife pattern, the sheath must be equipped with a suspension. To do this, mark and punch three holes.

The width of the straps should be slightly larger than the size of the holes by about two millimeters.

Thread the hangers through the holes.

Thus, you managed to make a suspension without seams.

To continue working on the craft for the knife, you scrape the sheath at the place where the skin is bent. After such processing, you can easily fold the workpiece in the center.

Now the product needs to be glued.

You can use any kind of glue that sticks to the skin.

You can fasten the edges with stationery clothespins. Wait a while for the glue to set. To continue to make products for the knife, the sheath must be completely dry.

After complete drying, cut off the irregularities along the edges with a knife.

Using grinding machine, smooth uneven ends.

Now you need to make a mixture with which you will impregnate the product. To do this, you need to take two measures of vodka and one measure of PVA glue. Stir them together so that the vodka and glue are completely mixed together.

Using a brush, apply the mixture to the craft in several layers.

This impregnation dries in fifteen minutes.

While the craft is not yet dry, mark the seam lines. This can be done using a fork.

She also marks the step of the seams.

Using a one-millimeter drill and a drill, drill holes for the seams on the front side. In this case, the drill must be kept exclusively in a vertical position.

Now cut a groove, connecting all the holes. In this case, this was done using a special Chinese tool.

Now you can paint the craft for the knife. The scabbard can, for example, be stained.

Cover with stain several times to make the color darker.

Once the scabbard is dry, sand it down with sandpaper, increasing the size. First, use one hundred and eightieth size, then two hundred and fortieth and then three hundred and twentieth. At the end, polish with a six hundredth.

Sew the product along the holes using a waxed thread in two needles, the type of seam is saddle.

Now you need to soak the knife sheath with shoe wax.

All is ready!

Sheath for camping knife

When you go out into nature or for a longer vacation, for example, by the sea, you always take with you such a necessary and indispensable item as a knife. So that he does not tear the fabric or the walls of the bag, his blade is wrapped with a rag or newspaper. However, you can do it easier - make a sheath for it, and then you will no longer have such a problem. Below we will describe and show how to make a scabbard.

What materials will be needed

Cotton fabric, which must first be impregnated with resin.
A piece of hard leather of good quality.
Strong needle and thread made of nylon.
Clothespins stationery.
Awl.
Pliers.
Drill.
Thin drill.
Calipers.
Well sharpened knife.
Well sharpened cutter.
A piece of strong wire.
Shoe cream for polishing crafts.

How to do?

First you need to make a solid tab, using cotton fabric for this. Cover the tip of the knife with paraffin and form a tab on it.

Now cut out a piece of leather of a suitable size and moisten it thoroughly. Then put the tab on the knife and place it in the center of the cut piece of leather.

Wrap the knife around this piece and fix the ends with stationery clothespins along the seam. Wait until the skin is completely dry.

After complete drying, remove the clothespins.

Now the product can begin to flash. To do this, use an awl to make two holes where the bend begins. Thread the thread from both sides into the holes, as a result you will get one stitch.

Poke the thread into the same holes in reverse order, you get the second stitch.

With an awl, mark the places where the rest of the holes will be. Make sure they are evenly spaced.

Using a drill and a thin drill, drill holes.

Continue to flash the product. If the needle comes out tight, help it out with pliers.

Cut off the ends of the threads and melt them over the fire. The hardest part is over.

With a knife, cut off the excess skin, leaving a little for the stock.

Using an abrasive skin, process the cut line.

Now make a pendant for the scabbard. Take a piece of leather and cut out a U-shaped figure from it. Cut small holes in the top of the workpiece with a knife.

Thread the ponytails through the holes at the top.

Now you pull out the knife from the craft, and instead of it you insert a wooden stick of the same size. Now mark the places where the mounting holes will be.

Using cutters, make holes according to the marks.

Thread the ends of the suspension into the holes as in the photo below.

Almost everything is ready, there are a couple of steps left.

Customize the size of the scabbard. To do this, moisten the knife well and insert it into the craft. Using wire, tighten tightly.

Wait until the skin is completely dry and remove the wire.

Now it remains only to cover the craft with shoe cream. In this case, the knife must be inserted into the sheath, and its handle must be wrapped in a bag.

Third option

In order to make a case of this type, you will need the following materials and tools:

Soft skin of the required size.
Sheet of cardboard.
Simple pencil.
Scissors.
Cutter.
Scotch tape.
Food film.
Kitchen towel.
Hot water in a pot.
Clamps.
Strong needle.
Waxed thread.

How to do?

First, draw a template.

To do this, lay the knife on the cardboard and circle its contours using a pencil. It is not necessary to circle butt, indent the contours by five millimeters. This will come in handy if the skin is thick. Now draw the other half mirror to the first. Draw the edge of one drawn half, it will be equal to the length of the handle. This is necessary so that later you can form a loop for closing the scabbard.

Now cut out the template along the drawn contours.

With the reverse side of the blade, you determine the exact line for bending the workpiece.

Fold the layout, glue it with adhesive tape and try on the knife. This is necessary in order to be able to adjust the dimensions. Do not forget that cardboard is much thinner than the thinnest kind of leather. Make sure that the knife easily enters the workpiece.

Expand the craft and transfer its contours to a piece of leather on the side where the suede is. For this purpose, you can use a pencil. Using a cutter, cut out the shape we need.

Wrap the knife with cling film.

Heat water in a saucepan and lower part of the skin into it as shown in the figure. This will make the skin soft.

Dry a piece of wet leather using a towel, and then wrap it around the blade and fasten the ends with clothespins. Wait for the piece to dry. While the skin dries, periodically checking that it is desired shape. If anything, adjust the product with your fingers, stretching where necessary.

Once everything is completely dry, remove the clothespins.

Cut off excess or protruding pieces of skin using a cutter. Then you cut out a thin recess with it where the seam will pass.

Mark the places where there will be holes for the stitches. There should be a distance of no more than five millimeters between the points. Make indentations at each point using an awl or other sharp object.