How to make a bar stool with your own hands? Metal bar stool dimensions.

Usual bar stool bun made from walnut and iron with a seat.

The iron was taken from ancient bed frames, and the wood from pieces of walnut. The height of the chair is approximately 64 cm.

The main detail of this homemade product is its shape, for easy welding and strengthening of pieces of iron. If you are a cook for the first time, this project will make you very familiar with this activity, and thanks to it you will learn how to cook perfectly.

Part 1: Getting started.

Let's start creating the shape of the future bar stool.

We cut the metal into 4 parts of 23.2 cm by 54.5 cm.

Everything was fastened with a side joint and secured with screws, so they formed 20 cm. square pipe 58.5 cm.

Part 2: The base in the form of an angle under the shape.

We make the base from a piece of lumber with a thickness of 9.5 cm.

The pieces themselves had to be cut beveled so that everything fit.

With the help of a tape measure, we will find a suitable angle and set it so that everything matches. Pieces of lumber went through the saw so that there would always be a beveled edge if needed.

Part 3: End of the base part.

We cut the tips of the beveled lumber under the base of the form at 45 degrees and adjust along the perimeter.

We fasten the beveled base with plywood and nail it with an edge. This part is not connected to the pipe, so it can be removed if necessary.

Part 4: Mark and cut off future legs.

The newly made shape will help you easily locate the legs. You don't need to take any measurements, just attach and mark.

Mark the bottom of each leg and cut off first. To mark up, we hang the corner of the form over the edge of the table, and fix the metal part in place.

When cutting pieces of legs, everything is placed in the form and then the upper ends are also marked.

Part 5: The top of the chair.

The upper part of the bar stool was made with 4 corners of the iron.

Everything was marked with the square made earlier and a regular stationery pen.

The resulting pieces are glued together, and then removed from the mold to fit the exact weld on each side.

Part 6: Vise.

It is better not to install a vice on wood as the author, since the bolts with which everything was fastened fly out and everything has to be redone.

Part 7: Footrest.

Now you can cut a few more pieces of metal for the future stand.

The pieces turned out to be 30 cm long and at an angle of 45 degrees.

Part 8: Finish the welded parts and skin them.

The stand and support were held with blocks for support and the top of the chair.

Metal linings were welded from below under each leg.

Now let's all grind sandpaper grit 40.

Part 9: Location.

The walnut that the author used lay with him for a very long time and then he decided to use it.

The main part of the mode is on two thickened boards.

All boards are cleaned with sandpaper.

We grind the beveled edges with sandpaper with a grit of 100 to 220.

Part 10: Painting.

Every person wants to equip their home with the most in the best way. To do this, people make stylish and original repairs and arrange furniture. Furniture items can not only be purchased in ready-made in stores, but also do it yourself.

The second option is economical Money, exclusive designs and a wide flight of fancy.

Bars appeared on the market not so long ago, but managed to become popular and in demand among owners of spacious kitchens or dining rooms, where in addition there is also a bar counter. Most often, they are found in spacious private houses, where there is a free place. If you are lucky enough to become the owner of such a home, then you should definitely put a few original and exclusive chairs near the bar counter, which will become the main decoration of the room.

To the main benefits self-manufacturing furniture items should include:

Peculiarities

Concerning design features, then bar stools are different forms, designs, sizes and materials of manufacture. According to the types of structures, they are divided into models:

Advice: if you are just starting to master the profession of a furniture maker, opt for a stool.

The choice of wood species

You can make a bar stool out of wood or metal. Metal constructions suitable for those who know how to work with a welding machine.

But to collect wooden product almost every person can, having little experience in carpentry and a great desire to make furniture with their own hands.

Furniture from natural wood will bring a special atmosphere to the interior hearth, warmth and comfort. It will delight owners not only with its environmental friendliness, but also with interesting shades, textures and textures.

When choosing wood, there are several factors to consider. Namely, the fact that by species the whole tree is divided into:

• Soft. These species include pine, birch, alder;
• The average. These are oak, cherry, beech;
• Solid. They should include maple, exotic trees, yew

Attention: in addition to the strength of wood, it is worth considering its resistance to moisture. Even hard varieties of trees do not always withstand increased moisture, and upon contact with it, they swell and lose their original appearance.

Softwood is the easiest to work with. But it does not have a long service life and high technical qualities. A chair made of soft varieties will serve the owners from 10 to 15 years. But this best option for beginners in carpentry. If you already have experience self assembly chairs, it is better to use more expensive types of wood, such as oak, beech, ash. Such chairs will serve you and your family for decades, and will delight you with aesthetics and ease of use.

You can make a bar stool from different breeds trees. The most sought after and popular are:

Drawing, standard dimensions of legs and seat

Before you start creating a drawing, you need to decide on the design and type of construction of the future chair. At this stage, consider:

• The number of legs. by the most good option will be the manufacture of a chair with four legs.
• Height adjustable. Of course, you can make a standard chair, but it will be much more convenient if its height can be adjusted.
• Ease of use. To do this, it is recommended to make a footrest, armrests and backrest at the chair.
• Upholstery and frame materials. The frame can be made of wood or metal. And for the upholstery, durable and beautiful fabrics are selected.

After that, the best option for creating a drawing of a bar stool is selected. And you can do it in different ways:

• Draw by hand with a pencil on a piece of paper or graph paper. This option is suitable for professional furniture makers who know how to present a piece of furniture in different projections and realize it all on paper.
• To find suitable option drawings on the Internet. This is the easiest, and all novice masters use this method. Here you will not need to calculate the size of the chair, calculate the number of consumables, come up with a design. Experienced craftsmen this will all be done for you.
• Use special computer programs. The most popular of them are: cutting, PRO - 100.

Which option to opt for is up to you. The main thing is that the drawing of the bar stool is thought out correctly. After all, its comfort in operation will depend on this.

Although there are many options for creating a bar stool drawing, the following factors should be considered. Namely, this piece of furniture must have certain dimensions:

It's just conventions. If the seat of the bar stool has a round or oval shape, its dimensions will differ significantly from those indicated above.

Also, when creating a drawing, it is worth considering that the seat can be both hard and soft. For the manufacture of soft seat additional preparation is required the following materials:

• foam rubber;
• upholstery fabric;
• furniture stapler;
• paint glue.

Tools and materials

Of the tools we need:

Of the materials in the workflow will be used:

• lumber;
• fasteners for legs;
• glue;
• self-tapping screws;
• paints and varnishes;
• stain;
• solvent;
• brushes.

How to make according to the standard?

Making a bar stool, like any other piece of furniture, begins with sawing the details. We will need to prepare the following individual elements:

• four stiffeners, the thickness of which must be at least 3 cm;
• two circles. The thickness of the first is 2 cm and a diameter of 26 cm, the thickness of the second is 3 cm and a diameter of 36 cm;
• four legs, each 3 cm thick.

Reference: a small circle will be used as a substrate, a large one as a seat.

After preparation individual elements bar stool, you can start assembling it. All parts are assembled with self-tapping screws, and to give the product strength, you can use PVA glue. The bar stool assembly process will look like this:

We have considered the easiest option for making a bar stool made of natural wood with our own hands.

If you want to make a recess in the seat, you need to cut it out on the surface, and then plan it with a chisel. Next, the seat is sanded and covered with paints and varnishes.

The seat of the bar stool can be made soft. To do this, foam rubber, at least 3 cm thick, is glued to plywood or boards, and upholstery fabric is nailed on top with a stapler.

Decorating wooden furniture

After making a bar stool, it must be decorated. Each master chooses his own version of decorating a piece of furniture made by himself.

Some just cover wooden surfaces stain and varnish or paint. Someone likes to carve the legs and back of furniture, someone prefers the decoupage technique.

The easiest way to decorate a bar stool is with fabric.. For these purposes, materials resistant to moisture and pollution are selected (tapestry, leather, leatherette, jacquard, microfiber).

It is not at all necessary to bother yourself with hauling furniture, sometimes it is enough just to sew covers on it. So you can update the interior of the room from time to time, creating new covers. When choosing a fabric for decoration, it is important to consider the overall interior of the kitchen or dining room. The chair should harmoniously fit into the environment and be its main decoration.

A photo

Ideas for decorating the resulting furniture and its use can be seen in the following photos:

Useful video

A detailed process of manufacturing, assembly and decoration can be viewed in the following video:

Conclusion

In conclusion, it is worth noting that all bar stools are unique and inimitable in their own way. They are able to bring into the interior a special atmosphere of warmth and harmony. A self-made chair with your own hands will become not only a decoration for the kitchen or dining room, but also a source of pride among your family members and guests.

In contact with

On the modern kitchen often they arrange a corner for relaxing behind the bar counter, for which chairs will certainly be needed.

A bar stool is a height-adjustable stool that is designed to be used in conjunction with a bar counter.

Tools and materials

• solid wood;
• screwdriver-drill;
• jigsaw;
• Sander;
• plane;
• roulette;
• pencil;
• drill.

For work, among other things, drills of 3 and 6 mm should be prepared (hereinafter, the dimensions will be indicated in millimeters). If, after making the chair, it is supposed to be stained before the varnishing process, it is preferable to purchase a solid birch, since pine is characterized by uneven staining. Stock up to be an array with a thickness of 30 and 20 mm. The first option will go to a circle, which needs to be given a diameter of 360 mm, and a jigsaw will be used when carrying out these works. This element will become the seat. If you have a milling machine or manual router an aesthetic profile can be provided around the perimeter. If this is not possible, you can chamfer using a planer, after which the treated surface should be ground.

A circle with smaller dimensions, the diameter of which should be equal to 260 mm, must be cut from an array of 20 mm. The same material should also be used to make stiffeners that will act as footrests. They need to be prepared using an array with a thickness of 30 mm, while making sure that the wood structure is located vertically.

The bar seat should be assembled using the following types of screws:

• 5x80 - for pairing the legs with each other and with a small circle;
• 5x40 - to fix the seat to a small circle;
• 5x20 - to fix the stiffeners, the elements must be matched with the legs with corners.

In the part for self-tapping screws, it is worth drilling holes, the diameter of which should be 6 mm, and at the end, the drilled holes should have a diameter of 3 mm.

After you managed to make a bar stool, you can cover its surface with stain. The layer should dry, after which you can begin to apply varnish.

Back to index

Alternative design

Balusters can be used as legs for a bar stool.

You can make a chair with your own hands and according to a different sketch. For the process, plywood 30 mm thick should be used. Balusters will become the legs, they can be replaced with cuttings for shovels, their diameter is 30 mm.

Detail (mm):

• legs (4 pcs.) - length 750;
• seat with a radius of 180;
• draft seat with a radius of 170.
• top ring with an outer radius of 143, an inner radius of 110;
• bottom ring with an outer radius of 153, an inner radius of 120.

Before cutting the rings, they will have to be marked for drilling. On the workpiece, you need to depict the outer contour of the element and draw 2 straight lines through the center of the circle. From the cross, set aside 140 in each direction, which will allow you to get the centers of the holes that you need to select with a drill. Now you can draw the inner contour by sawing a ring out of the drilled element.

The rough seat needs to be marked as the top ring, but it should be drilled ½ of the thickness, these will be the “nests” for the legs. The legs to the rings can be fixed with screws. Under them it is necessary to drill holes with a 6 mm drill. The upper ring should not be pulled immediately, insert the legs into the nests of the draft seat, where PVA is poured in advance.

The draft seat must be connected to the legs with 5x60 self-tapping screws. Now you can proceed to fixing the upper seat with 4x40 self-tapping screws.

The manufacturing process of the structure can be completed by tinting with a stain and varnishing everything.

1. Characteristics of the bar stool.
2. Tools and materials.
3. Manufacturing sequence.
Bar stools are convenient attributes for tables with a height of more than 850 mm. Outwardly, they may look like ordinary stools, but only with elongated legs. The height of the chair should be 300 - 350 mm lower than the level of the tabletop.

The remaining parameters (width, length, height of the legs, the presence of a back) are adapted to the wishes of the user and the design of the room. Consider how you can make a bar stool with your own hands from a bar, which, for example, can be purchased at hardware stores.

Tools and materials.

For the manufacture of the presented model, you will need the following set of tools:

• - square;
• - roulette;
• - a simple pencil;
• - drill;
• - drills with a diameter of 2.5 mm, 3.5 mm;
• - manual milling machine with nozzles;
• - hammer;
• - a screwdriver with a cross profile;
• - sanding paper with different grain sizes;
• - vibratory grinder;
• - core;
• - soft brush for painting;
• - stationery knife.

The following materials are required, part number in brackets:
1. wooden beam for legs, section 30 by 40 mm and length 600 mm, in the amount of 4 pcs. (1A, 1B, 1C, 1D).
2. Wooden beam for tsarg and prolegs with a section of 30 by 40 mm and a length of 300 mm - 4 pcs. (2); 320 mm - 4 pcs. (3).
3. Beam for connecting the elements of the seat, size 25 X 30 X 315 mm - 2 pcs. (4).
4. Wooden beam for the seat with dimensions 20 X 40 X 320 mm - 8 pcs. (five).
5. PVA glue.
6. Screws, 80 mm long, 16 pcs. and 45 mm - 4 pcs.
7. Nails for 1 X 30 mm - 16 pcs.
8. Rag to wipe off excess glue.
9. Colorless varnish.
10. Felt coasters with self-adhesive surface.
To prevent weakening of the chair structure, all wooden elements it is desirable to use without knots.
In the presented material, the bar stool is assembled from a common type of wood - pine.

Manufacturing sequence.

To make a bar stool with your own hands, you can follow the following sequence:
Step 1
Round off the bars intended for legs, sides, prolegs on all sides using a manual milling machine and an appropriate nozzle.
Step 2
Using a hand router with the same tool as in step 1, round off the seat blanks on one side to a length and width of 40mm.
Step 3
Clean all elements of the chair with sandpaper until the surface is smooth.
Step 4
On the legs, drill holes with a diameter of 3.5 mm for fastening the legs and drawers. Their coordinates are shown in Figure 1.
Step 5
Based on the photo, lean the parts against each other and mark the attachment point with self-tapping screws through the holes in the legs.

To reduce the stress that occurs in the process of tightening the fasteners at the ends of the parts, drill blind hole 2.5 mm in diameter and about 30 mm deep.
Step 6
Self-tapping screws for drilled holes fasten together the blanks of the legs, tsarg, prolegs.
Step 7
On the resulting chair frame, unscrew the screws so that they do not come out of the body of the workpiece, but the ends of the part could be smeared with glue.
Step 8
Lubricate the ends of the frame with glue and tighten the fasteners until its head is placed flush with the surface of the beam. Remove the protruding PVA particles with a rag.
Step 8
To drawer sides No. 2, with 40 mm screws, attach a beam for attaching the seat from the inner side so that one side of the beam with a width of 25 mm is adjacent to the drawer side, and in the lower part is flush with it.

Step 9
Remove the screws from the seat blank and apply glue to the side adjacent to the chair. Connect these elements.
Step 10
From the side of the seat, apply glue to the support bar (20 X 25 mm) and, setting the seat blanks close, from the first to the eighth, nail them to the support. Dip the nail heads into the body of the tree with a core. Remove excess glue with a rag.
Step 11
Clean the surface of the chair from dust. Putty potholes, recesses in the tree. Clean all the elements with sandpaper. Using a brush, apply varnish evenly over the entire surface of the bar stool. Let the product dry.
Step 12
When used as a soft sole under the legs of a chair of a solid canvas with a self-adhesive film, determine the dimensions of the end part of the leg and, based on these data, cut out the appropriate elements from the specified material.

Now it has become fashionable to equip a bar counter in the kitchen or living room. An individual approach automatically generates the question, how to make a bar stool with your own hands? Of course, you can buy them in the store, but independent work will give you the opportunity to make a unique model that will be impossible to buy.

The most popular option for how to assemble a bar stool is to use wood and plywood. You can use metal inserts, but this will complicate the work at home. In order to make a wooden bar stool without being distracted, you should prepare the basic tools and materials:

• screwdriver;
• drill;
• hammer;
• jigsaw;
• roulette and corner;
• bit;
• plane;
• self-tapping screws;
• grinder.

The Internet has a lot kitchen furniture from step by step description its manufacture at home. You can try with solid wood and plywood, this material is not difficult to get, but it is almost impossible to spoil it.

Before proceeding directly to the manufacture of bar stools, you should draw an exact diagram of the product. If you know how to disassemble a bar stool, then it will be easier for you to imagine it in parts, thereby completing each detail yourself. The prepared scheme will help determine consumable. The height of your model should be such that the distance between the seat and the table top is no more than 40 centimeters.

Assembly of prepared parts

When choosing a tree for a bar stool with your own hands, pay attention to pine or birch. They have a fairly long service life, besides, they are easy to work with. How to choose material for home furniture can be viewed on the Internet, there are many photo and video files on this topic. The thickness of the material should be 25 - 30 centimeters, then you will not have to doubt the strength of the seat.

A standard wooden bar stool consists of:

• circle with a diameter of 40 mm., and a thickness of 30 mm. No. 1;
• circle with a diameter of 30 mm., and a thickness of 20 mm. No. 2;
• legs with a thickness of 30 mm., the length is chosen arbitrarily in the amount of four pieces. No. 3;
• stiffener 30 mm., in the amount of four pieces.

Next, we will show you how to make your own several options for bar stools.

Option 1. A chair with a round seat

The first part will serve as a seat. The second (small circle) - with a substrate under the seat Chair legs From an array 20 mm thick we cut out the stiffeners

The ribs are attached to the legs with the help of corners, which are placed from below, from the side of the floor. We tint the chair with stain. Dry and open with varnish in 2-3 layers. Bar stool ready

Option 2. A chair with a curved seat

Creating a drawing

We take 4 beams 40x40 mm We fasten the legs. Installing the crossbars Attaching the top and bottom rails
With a hand saw in the board, we make several cuts of various depths. Cut out the seat. We attach the seat to the chair, which we varnish after assembly. The chair with a curved seat is ready

A bar stool made of wood with your own hands looks simply gorgeous. We collect all the details gradually, carefully connecting them together. The larger circle is the seat, the smaller one is the underlayment. Basically, bar stools for the kitchen come in a round shape, so you can stick to the standard option for a start.

To begin with, we attach the legs to the small circle on the screws. In order not to have to disassemble the product later, make marks on the tree with a special pencil. Then we fix the stiffeners, also according to the pre-prepared markings. The final step is to mount the seat. The chair should be comfortable and therefore the screws should not be felt by hand.

How to decorate a chair?

Woodwork will never go out of fashion. Therefore, the most convenient way will varnish them, of course, if it is combined with a bar counter. In general, there are no restrictions on decoration, it all depends on the desire of the creators. Most importantly, sand the product before painting.

Chairs with metal inserts

You can make a stool with your own hands with metal inserts. This method can not only decorate externally, but also add strength. Forged bar stools look expensive and stately, but to make them yourself you need good blacksmith skills and a workshop. You can make legs out of profile pipe with your own hands, this diversifies the model.

In this case, you can install a gas lift mechanism. It will help to adjust the height of the seat itself without getting up from it. When it breaks, the chair is not thrown out, disassembly and replacement of the mechanism is carried out quickly and is quite cheap. Preliminary drawings are also being prepared for such chairs and it doesn’t matter what you make your chair from, metal or pipes.

Metal bar stools (photo 1) Metal bar stools (photo 2)

When choosing which chair model to make at home, do not focus on standard templates. Individual approach and personal preferences will make it unique.