Bamboo flutes in feng shui - protection, support and good luck in the house. How to Use Bamboo Flutes Pipe Making Materials and Tools

Svirel (it is also called "snot" or "string") is one of the types of longitudinal flute, common in Russia. According to Slavic legend, Lel, the son of the goddess of love, played the flute. Therefore, it was believed that the flute can awaken mutual feelings.

Materials and tools for making a flute

To make a flute out of wood with our own hands, we need a rather impressive arsenal:

sandpaper
small wooden plug (1.5 cm in diameter and 4 cm long)
ruler
pencil
tuner
small vices (not necessary, but they are much more convenient)
something with which you can drill (drill, drill, engraver) and drills different diameters: about 0.8 to 4.2 mm
needle file
semicircular cutter
pair of clamps
PVA glue
two wooden blocks 30 × 2x1 cm.

Making a flute with your own hands

First, we take wooden blocks and mark them. It is necessary to draw the boundaries of the inner channel of the flute, on one side of the bar this channel is 1.5 cm wide, and on the other, 1 cm, that is, the channel will narrow slightly towards the end of the flute.

Now we clamp one of the bars into a vise and begin to cut out a semicircular channel. On my workpiece, an area is shaded that will need to be removed with a cutter.

Carefully and slowly remove the chips, follow the direction of the wood fibers. They may not always go along the workpiece, so be careful, otherwise the cutter may go crooked.

We try to cut the channel to an even semicircle along the entire length. We do the same with the second bar.

When both halves are cut out, they need to be sanded. With a piece of sandpaper we pass along the inner surface of the channel, achieving smoothness.

After grinding, we move on to the whistle. Stepping back 4 cm from the upper edge of the workpiece (where the wide end of the channel is), draw a rectangle 5 by 7 cm, preferably exactly in the center.

With a 4.2 mm drill, we make three holes close to each other, so that an oval window is obtained.

Now we take a needle file and bring the window to a rectangular shape, according to the markings made.

After that, with the same file, we grind one side of the window at an angle of about 30-45 degrees. This is the most important part of the work: the sound quality will depend on the sharpness and smoothness of the edge.

It's time to put the halves together. We smear them with PVA glue and fold them, carefully aligning the channel. We press with clamps and leave to dry for a couple of hours.

When the glue dries, unwind the clamps and take the knife. Cut off the top of a small wooden sleeve, about 1.5 mm, so that you get a flat, even edge. Look at the photo and everything will become clear.

After that, grease the sleeve with glue and insert it from the upper end of the flute, forming a whistle. Cut edge up, exactly to the edge of the whistle window.

We wait until the glue dries, and we take the knife. Gently cutting the workpiece, give it a rounded shape, then smooth it with sandpaper.

To make it convenient to play, we will make a cut at the upper end of the flute at the back.

Now the fun part is the setup. Try blowing into the flute, listen to the sound and check with the tuner. If you did everything carefully, you will get A sharp. This is the lowest sound that our flute can produce.
In total, we will have seven notes and six playing holes. Let's mark them: the very first hole will be 6 cm from the lower end of the pipe, the remaining holes - in 2 cm increments.

Armed with drills of different diameters, we begin the setup. The flute is often tuned in natural major. This means that we should get such a series of sounds: A sharp - Do - Re - Re sharp - Fa - Sol - La.

The general tuning principle is this: the larger the hole, the higher the sound. Therefore, first we drill a very small hole, listen. If you need a sound a little higher, drill more. The main thing is not to overdo it, because making the hole smaller will not work.

Start drilling from the lowest hole. When it is configured, go to the second. The second hole is adjusted with open ground and so on. That is, when you listen to sound from a hole, this hole and all holes below it must be open.

OK it's all over Now! The flute is ready, you can start playing. And you can decorate it to your taste. I just covered my flute with stain.

Materials:

Gas torch or fire for heating a metal rod;
Steel rod with a minimum diameter of 12 mm;
Potholder or heavy cloth;
Hacksaw for metal with frequent teeth;
Marker;
A sheet of sandpaper with fine grain;
Old drill with a diameter of 6mm;
Pliers;
Old bamboo fishing rod;
Roulette;
Linseed oil and a rag.

Instruction:

Cut a piece of bamboo at least 45-50 cm long and 20-25 mm in diameter from the bottom of the old bamboo rod. Be sure to cut it off so that one end is covered by a partition between the sections. (see pic.)

Measure and mark a spot 25mm apart at the end of the covered part of the bamboo. Measure 150mm from the first mark and make five more marks 25mm apart. When you're done, you should have a total of seven marks. (see pic.)

In the next step, you need to use a 12 mm rod to burn through the unnecessary partitions and clean out the unnecessary fibers from the bamboo flute. To do this, heat one end of a steel rod until it turns red. *WARNING* - be sure to use an oven mitt or heavy cloth when holding the other end of the rod as it will be very hot. When the rod is hot, insert it into the open end of the bamboo and press lightly to burn through the partitions. Be sure to leave the last baffle (the end of the flute) (see pic.)

Next you need to heat up the 6mm drill bit. Use pliers to do this and burn holes in the places you marked. Don't drill holes in the bamboo as it will burst (see pic.)

Take a piece of fine grit sandpaper, about 7cm x 7cm, and roll it up. Using rolled sandpaper, remove the bamboo embers from any burnt holes. You can also use sandpaper to widen the blow hole. This will make it easier to get sound, but make sure you don't make the hole too big.

Cover the flute with a layer of linseed oil. Place three fingers of each hand on 6 holes. Blow into the inlet (near the closed end of the flute) at an angle. Practice until you get a consistent tone. Now you can remove your finger to get a different sound. If it doesn't work out well, you can try to practice on empty bottle. Try blowing into the bottle by touching the neck with your lower lip. The same principle is used when extracting sound from a flute. Don't be discouraged if you don't succeed right away. Playing the flute requires a certain amount of skill.

Basic information Avlos - ancient woodwind musical instrument. Avlos is considered a distant predecessor of the modern oboe. It was distributed in Asia Minor and Ancient Greece. The performer usually played two aulos (or double aulos). Playing the aulos was used in ancient tragedy, in sacrifice, in military music (in Sparta). Solo singing accompanied by playing the aulos was called aullodia.

Basic information The cor anglais is a woodwind musical instrument, which is an alto oboe. The English horn got its name due to the erroneous use of the French word anglais (“English”) instead of the correct angle (“curved angle” - in the form of a hunting oboe, from which the English horn originated). Device According to the device, the English horn is similar to the oboe, but has a larger size, pear-shaped bell

Basic information Bansuri is an ancient Indian woodwind musical instrument. Bansuri is a transverse flute made from whole piece bamboo. Has six or seven playing holes. Bansuri is widespread in India, Pakistan, Bangladesh and Nepal. Bansuri is very popular with shepherds and is part of their customs. It can also be seen in Buddhist painting around 100 AD.

Bass clarinet (Italian: clarinetto basso) is a woodwind musical instrument, a bass variety of the clarinet that appeared in the second quarter of the 19th century. The range of the bass clarinet is from D (large octave D; on some models, the range is extended down to B1 - B flat contra octave) to b1 (B flat first octave). Theoretically, it is possible to extract higher sounds, but they are not used.

Basset horn is a woodwind musical instrument, a kind of clarinet. The basset horn has the same arrangement as the normal clarinet, however great length, which is why it sounds lower. For compactness, the basset horn tube is slightly curved at the mouthpiece and at the bell. In addition, the instrument is equipped with several additional valves that extend its range down to the C note (as it is written). Basset horn tone

Basic information, history The recorder is a woodwind musical instrument from the family of whistling wind instruments, such as the flute, ocarina. The recorder is a type of longitudinal flute. The recorder has been known in Europe since the 11th century. It was widespread in the XVI-XVIII centuries. Used as a solo instrument, in ensembles and orchestras. A. Vivaldi, G. F. Telemann, G. F.

Key information Brelka is a Russian folk woodwind musical instrument that existed in the past in the pastoral environment, and now occasionally appears at concert venues in the hands of musicians of folklore ensembles. The key fob has a strong sound of a very bright and light timbre. The keychain is essentially nothing more than an ancient version of the oboe, however, compared to the shepherd's pity,

Basic information Whistle is a woodwind musical instrument, a Celtic folk pipe. Whistles are made, as a rule, from tin, but there are also wooden, plastic and even silver versions of the instruments. Whistle is very popular not only in Ireland, but throughout Europe. Most whistles, however, are made in England and Ireland, and are the most popular among whistlers. Whistles exist

Oboe is a soprano register woodwind musical instrument, which is a conical tube with a valve system and a double reed (tongue). The instrument has a melodious, but somewhat nasal, and in the upper register - a sharp timbre. Instruments that are considered the direct predecessors of the modern oboe have been known since antiquity and have been preserved in their original form in different cultures. Folk instruments such

Basic information The oboe d'amore is a woodwind musical instrument, very similar to an ordinary oboe. The oboe d'amore is slightly larger than the regular oboe and, in comparison, produces a less assertive and softer and calmer sound. In the oboe family, it is set as a mezzo-soprano or alto. The range is from salt of a small octave to re of the third octave. oboe d'amour

Basic information, origin Di (hengchui, handi - transverse flute) is an ancient Chinese woodwind musical instrument. Di is one of the most common wind instruments in China. It was supposedly brought from Central Asia between 140 and 87 BC. BC. However, during recent archaeological excavations, bone transverse flutes of about

Basic information The didjeridoo is the oldest woodwind musical instrument of the aboriginal peoples of northern Australia. One of the most ancient musical instruments on Earth. The didgeridoo is the European-American name for Australia's oldest musical instrument. In northern Australia, where the didgeridoo originated, it is called yidaki. The didgeridoo is unique in that it usually sounds on one note (the so-called

Basic information Dudka is a folk wind wooden musical instrument, consisting of a wooden (usually elderberry) reed or reed and having several side holes, and a mouthpiece for blowing. There are double pipes: two folded pipes are blown through one common mouthpiece. In Ukraine, the name sopilka (snot) has survived to this day, which is rare in Russia, in Belarus it

Basic information Duduk (tsiranapokh) - a woodwind musical instrument, is a pipe with 9 playing holes and a double reed. Distributed among the peoples of the Caucasus. Most popular in Armenia, as well as among Armenians living outside of it. The traditional name of the Armenian duduk is tsiranapokh, which can literally be translated as “apricot pipe” or “soul of an apricot tree”. Music

Basic information Zhaleika - an old Russian folk wind wooden musical instrument - a wooden, reed or cattail tube with a bell made of horn or birch bark. Zhaleika is also known as zhalomeika. Origin, history of zhaleyka The word "zhaleyka" is not found in any ancient Russian written monument. The first mention of a zhaleyka is in the notes of A. Tuchkov dating back to the end of the 18th century.

Basic information Zurna is an ancient woodwind musical instrument common among the peoples of Transcaucasia and Central Asia. A zurna is a wooden tube with a socket and several (usually 8-9) holes, one of which is on the opposite side. The range of the zurna is about one and a half octaves of the diatonic or chromatic scale. The timbre of the zurna is bright and piercing. Zurna is in close proximity

Basic information Kaval is a shepherd's woodwind musical instrument. The kaval is a longitudinal flute with a long wooden barrel and 6-8 playing holes. At the lower end of the barrel there can be up to 3-4 more holes for tuning and resonating. The kavala scale is diatonic. The length of the kaval reaches 50-70 cm. The kaval is widespread in Bulgaria, Moldova and Romania, Macedonia, Serbia,

Basic information, device Kamyl is an Adyghe wind wooden musical instrument, a traditional Adyghe (Circassian) flute. Kamyl is a longitudinal flute made from a metal tube (most often from a gun barrel). There are 3 play holes at the bottom of the tube. It is possible that the instrument was originally made of reed (as the name indicates). The length of the reed is about 70 cm.

Basic information Kena (Spanish quena) - woodwind musical instrument - longitudinal flute used in music Andean region Latin America. The kena is usually made of reed and has six upper and one lower playing holes. Typically, kena is done in G (G) tuning. The quenacho flute is a lower pitched variant of the quena, in D (D) tuning.

Basic information The clarinet is a woodwind musical instrument with a single reed. The clarinet was invented around 1700 in Nuremberg, and has been actively used in music since the second half of the 18th century. It is used in a wide variety of musical genres and compositions: as a solo instrument, in chamber ensembles, symphony and brass bands, folk music, on the stage and in jazz. Clarinet

Basic information Clarinet d'amour (Italian: clarinetto d'amore) is a woodwind musical instrument. Device Like the species instrument, the d'amore clarinet had a single reed and a cylindrical tube, but the width of this tube was less than that of a conventional clarinet, sound holes were also narrower. In addition, the part of the tube to which the mouthpiece was attached was slightly curved for compactness - the body

Basic information Kolyuk - a woodwind musical instrument - an ancient Russian variety of a longitudinal overtone flute without playing holes. For the manufacture of thorns, dried stems of umbrella plants are used - hogweed, shepherd's pipe and others. The role of a whistle or beep is played by the tongue. The height of the sound is achieved by overblowing. To change the sound, the bottom hole of the tube is also used, which is clamped with a finger or

Basic information Contrabassoon is a woodwind musical instrument, a kind of bassoon. The contrabassoon is an instrument of the same type and device as the bassoon, but with a twice as large column of air contained in it, which makes it sound an octave lower than the bassoon. The contrabassoon is the lowest sounding instrument of the woodwind group and performs a contrabass voice in it. Names of the contrabassoon

Basic information Kugikly (kuvikly) is a woodwind musical instrument, a Russian variety of the multi-barreled Pan flute. Kugicle device Kugicles are a set of hollow tubes of various lengths and diameters with an open upper end and a closed lower one. This tool was usually made of kugi (reed), reed, bamboo, etc. stems, the trunk knot served as the bottom. Nowadays, plastic, ebonite

Basic information Kurai is a national Bashkir woodwind musical instrument similar to a flute. The popularity of kurai is associated with its timbre richness. The sound of kurai is poetic and epicly sublime, the timbre is soft, accompanied by a throaty bourdon sound when played. The main and traditional feature of playing kurai is the ability to play with a chest voice. A light whistle is forgiven only for novice performers. The professionals play the melody

Basic Information Mabu is a traditional woodwind musical instrument of the Solomon Islanders. Mabu represents wooden pipe with a socket, hollowed out from a piece of a tree trunk. A half of a coconut was attached to the upper end, in which a game hole was made. Large specimens of mabu could reach up to a meter in length with a mouth width of about 15 cm and a wall thickness of about

Basic information Mabu (mapu) is a traditional Tibetan woodwind musical instrument. Translated from the nose, “ma” means “bamboo”, and “bu” means “pipe”, “reed flute”. Mabu has a bamboo stem with a single scoring tongue. There are 8 playing holes made in the flute barrel, 7 upper ones, one lower one. At the end of the trunk is a small horn socket. Mabu is also sometimes made

Basic information, characteristics Small clarinet (clarinet-piccolo) is a woodwind musical instrument, a kind of clarinet. The small clarinet has the same structure as the regular clarinet, but is smaller in size, which is why it sounds in a higher register. The timbre of the small clarinet is harsh, somewhat noisy, especially in the upper register. Like most other instruments of the clarinet family, the small clarinet is transposing and is used

Basic information, device Nay - Moldavian, Romanian and Ukrainian woodwind musical instrument - a longitudinal multi-barreled flute. Nai consists of 8-24 tubes of different lengths, reinforced in an arched leather clip. The length of the tube determines the pitch of the sound. Sound row diatonic. On the nai, folk melodies of various genres are performed - from doina to dance motifs. The most famous Moldovan naists:

Basic information Ocarina is an ancient woodwind musical instrument, a clay whistle flute. The name "ocarina" in Italian means "gosling". The ocarina is a small egg-shaped chamber with four to thirteen finger holes. The ocarina is usually made in ceramic, but is sometimes also made of plastic, wood, glass or metal. By

Basic information Pinquillo (pingulo) - an ancient woodwind musical instrument of the Quechua Indians, a reed transverse flute. Pinkillo is common among the Indian population of Peru, Bolivia, Northern Argentina, Chile, Ecuador. The Pinkillo is the ancestor of the Peruvian quena. Pinkillo is made from cane, traditionally cut "at dawn, away from prying eyes." It has 5-6 side playing holes. Pingulo length 30-32 cm. Pingulo range approx.

Basic information, application A transverse flute (or just a flute) is a woodwind musical instrument of the soprano register. Names of the transverse flute on different languages: flauto (Italian); flatus (Latin); flute (French); flute (English); float (German). The flute is available in a wide variety of performance techniques; it is often entrusted with an orchestral solo. The transverse flute is used in symphony and brass bands, and also, along with the clarinet,

Basic information Russian horn is a woodwind musical instrument. Russian horn has different names: in addition to "Russian" - "shepherd", "song", "Vladimir". The name "Vladimir" horn acquired relatively recently, at the end of the 19th century, as a result of the success that the performances of the horn choir conducted by Nikolai Vasilyevich Kondratyev from the Vladimir region had. Horn tunes are divided into 4 genre varieties: signal, song,

Basic information Saxophone (Sax - the name of the inventor, phone - sound) is a woodwind musical instrument, belonging to the wood family according to the principle of sound production, despite the fact that it is never made of wood. The family of saxophones was designed in 1842 by the Belgian musical master Adolf Sax and patented by him four years later. Adolf Sachs named his first constructed instrument

Basic information Svirel is an ancient Russian woodwind musical instrument of the longitudinal flat type. Origin, history of the flute The Russian flute has not yet been sufficiently studied. Experts have long been trying to correlate existing whistle instruments with ancient Russian names. Chroniclers most often use three names for instruments of this type - a flute, a sniff, and a forearm. According to legend, the son played the flute Slavic goddess love frets

Basic information Suling is an Indonesian woodwind musical instrument, a longitudinal whistle flute. The suling consists of a bamboo cylindrical trunk, about 85 cm long and equipped with 3-6 playing holes. The suling sound is very gentle. Usually sad melodies are played on this instrument. The suling is used both solo and as an orchestral instrument. Video: Sulingna video + sound Thanks to these videos you

Basic information, device, application Shakuhachi is a woodwind musical instrument, a longitudinal bamboo flute that came to Japan from China during the Nara period. The Chinese name for the shakuhachi flute is chi-ba. Standard length shakuhachi flutes - 1.8 Japanese feet (which is 54.5 cm). This determined the very Japanese name of the instrument, since "shaku" means "foot", and "hachi" means "eight".

Basic information Tilinka (calf) is a Moldavian, Romanian and Ukrainian folk woodwind musical instrument, which is an open pipe without playing holes. Tilinka is common in rural life, most often used by peoples living near the Carpathian Mountains. The sound of the tilinka depends on how much the musician closes the open end of the tube with his finger. The transition between notes is carried out by overblowing and closing / opening of the opposite

Article written by Robert E. Kramer

Materials:

1 propane or butane torch or fire to heat the metal rod
1 steel rod approximately 1/2" in diameter
1 oven glove or hard cloth
1 well-sharpened cutting object such as a hacksaw
1 pencil or magic marker
1 fine sheet sandpaper
1 old 1/4" drill
1 pliers
1 old bamboo rod
1 ruler
Linseed oil and a rag

Manufacturing

Cut from the end of the old rod a piece of bamboo about 45.7 cm to 50.8 cm long, with a diameter somewhere between 1.9 cm and 2.54 cm. Make sure you cut the bamboo so that one end remains blocked by the fibrous material that fills the bamboo between sections(see fig 1).

Measure and mark a point 2.54 cm in diameter from the closed end of the bamboo tube. Next, mark a distance of 15.24 cm from your first mark, then make five more marks 2.54 cm apart. When you are done you should have a total of seven marks (see fig. 2).

Your next step is to use a steel rod (diameter - 1.27 cm) to burn off the unwanted fibrous material. To do this, heat one end of a steel rod to red heat. *WARNING* - REMEMBER TO USE THE OVEN GLOVE OR HARD CLOTH WHEN HOLDING THE UNPINLED END OF THE ROD AS IT WILL BE VERY HOT TOO. When the rod is hot, insert it into the open end of the bamboo tube and apply moderate force to burn through the fiber layer. Don't forget to leave last layer fibrous material (at the closed end) intact (see Fig. 3).

Next, you need to heat the drill (diameter - 0.635 cm) to redness. Use pliers to hold the drill bit and burn holes in the places you marked. Do not drill holes in the bamboo tube with a drill, as this may cause cracks in the bamboo (see fig. 4).

Take a piece of fine sandpaper about 7.62 x 7.62 cm and twist it. Use rolled sandpaper to remove the black burnt bamboo from and around the holes you burned. You can also use sandpaper to widen the playing hole. This will help you pick up the sound more easily, not only don't make the hole too big (see fig. 5).

Wipe the finished flute with a cloth dampened linseed oil. Close the remaining six holes with the index, middle and ring fingers each hand. Blow into the sound hole ( nearest to the end - approx. translator) as if you were trying to make a sound by blowing into glass bottle from coca-cola. Keep trying until you get an even note. Now you can remove one finger to get a different sound. Experiment and practice. Good luck with your fun!!!

For real ideal material for the manufacture of musical wind instruments there will be bamboo. Firstly, it is hollow inside, and the stem has partitions, so there will be no need to additionally make a cork. Secondly, bamboo does not need additional drying. And real craftsmen create even saxophones and flutes from bamboo. The most common bamboo flute can be made by hand.

First you need to choose a suitable bamboo stalk. It can be grown very quickly in the country or even on an ordinary windowsill. In addition, an old bamboo rod or part of a curtain will do if it is made of stems of sufficient length. The diameter of the bamboo should be from 2 to 2.5 cm. But nothing bad will happen if the tool turns out to be a little thicker or thinner.

Using a jigsaw with a fine file, cut a piece of bamboo about half a meter long. You need to saw off so that at one end of the flute there is a natural cork.

Mark the first, inlet, hole, for which, from the end on which the cork is located, measure 2.5 cm with a ruler. It will be convenient to make marks with a regular marker. From the applied first mark, measure another 15-20 cm on the same side, making a second mark. Stepping back from the second mark again 2.5 cm, put the third mark. Make 4 more exactly the same marks. If everything is done correctly, you will end up with 4 marks.

Next, you need to get rid of unnecessary natural partitions. Most likely there will be 2-3 of them. And you need one, only the one that closes the tool from the end. You can get rid of them using a heated steel rod. With its help, excess fibrous plugs are burned out. First you need to heat the rod either on gas burner, or at the stake red-hot. At the same time, hold the other end of the rod with an oven mitt, for example, using a kitchen mitt.

The next step in creating a flute is drilling holes. It is best to do this with a drill with a diameter of just over 0.6 cm. Do not use an electric drill for this, otherwise cracks will appear on the bamboo. Can apply hand drill, but the handle must be turned slowly with care. The drill needs to be red-hot.

Of course, the potholder will no longer help here, so it's better to use pliers.

And the last moment. Wrap fine sandpaper, such as knitting or bicycle needles, and process the inside of the flute.

How to make a bamboo flute

http://website/assets/modules/svensoft-social-share-buttons/images/placeholder.png

A truly ideal material for making musical wind instruments would be bamboo. Firstly, it is hollow inside, and the stem has partitions, so there will be no need to additionally make a cork. Secondly, bamboo does not need additional drying. And real craftsmen create even saxophones and flutes from bamboo. The most common bamboo flute can be made by hand. First you need to choose […]