Do-it-yourself installation of the built-in hob. Ways to install the hob in the countertop with your own hands

In the conditions of an apartment, the installation location of the gas panel is determined by the location gas pipe. A shut-off valve must be installed on the gas pipe. It is worth noting that the transfer of a gas pipe to any distance should be done only by specialists of a gas company. At the same time, no one forbids installing a gas panel at a certain distance from the pipe, using a flexible gas supply (gas hose) for this.

Bellows hose, flexible gas connection

measurements

Before purchasing a panel, you need to know the width of the countertop. The dimensions of most panels are standard and do not go beyond 55-57 cm. In the documentation for the panel, not only the dimensions of the panel, but also the size of the hole in the countertop for installing the panel should be indicated.

Panel Installation Diagram

To protect the surface of the countertop from the movement of the jigsaw sole and from chipping when cutting, masking tape is glued next to the markings or along the markings.

So that the cut does not fall and break the countertop, you need to support it from below, as in the photo, with clamps.

Cutting tabletops with a jigsaw

Preparing the panel for installation

The kit includes jets for the main connection to the panel. If they are not installed, they must be replaced. The jet installation diagram is glued to the bottom of the panel or indicated in the passport.

If gas panel connects to gas bottle, jets need to buy others.

Jets

The layout of modern furniture sets for the kitchen provides for a built-in electric or gas stove, the hob and oven of which are mounted separately. The built-in panel is a functionally finished product, which, in principle, can be used without a kitchen. This article will tell you how to install a built-in hob and connect to the network with your own hands. The surface can be electric, gas or a combination, but the basic rules that should guide the operation are the same for all versions.

Step by step installation instructions

Speaking of tools, if the built-in panel is installed in a new set, and the hole for mounting the case in the countertop has not yet been made, a drill and an electric jigsaw are required. To connect to the mains, you will also need a screwdriver, pliers, a voltage indicator.

The first thing to take care of is a 220 volt electrical outlet, which will include a built-in hob. The choice of its location and installation must be carried out before the installation of furniture. In addition to the panel, the oven is included in the set of the stove. If the first is placed without a cabinet, it can be plugged into one outlet. Install electrical outlet should be lower than the built-in hob will be in order to prevent it from being exposed to moisture and grease during cooking.

When and kitchen wall completed, you can get to work. You can install the built-in hob according to the following step-by-step instructions:

1. First you need to determine the dimensions of the mounting opening, which must be cut in the countertop. This information can be found in the instructions provided by the manufacturer. If there is no instruction, you need to carefully measure the seats. It’s a good idea to make a cardboard layout according to these dimensions (sometimes it is included in the kit), which then needs to be installed on the tabletop and circled with a pencil. It is necessary to provide a gap between the landing parts of the body and the edges of the table from 1 to 2 millimeters.
   
2. Carefully mark the future hole. You will need a long ruler and a pencil. Do not forget that the tabletop is made of pressed sawdust and decorated with a coating of artificial stone. For this reason, you should not cut a hole closer than 50 mm to the edge, as thin sections of the table may collapse.
3. Carefully drill holes in the corners of the marked area with a drill, without going beyond it. We use a drill 8 - 10 mm for this purpose. In the process of drilling, it must be installed and held strictly perpendicular to the surface.
   
4. Insert into electric jigsaw a fine-toothed wood blade to avoid chipping the tabletop surface at the edge of the slot. Having inserted the canvas into one of the prepared holes, we make a cut according to the markup, firmly pressing the jigsaw to the surface. After cutting, we make sure that the built-in hob fits easily into the seat with a small gap. Otherwise, the edges of the hole should be trimmed.
   
5. It is desirable to protect the end sections of the slot made from moisture. For this purpose, the edges are processed with a sealant, as shown in the photo below. Then you can stick the seal included in the kit.
   
6. Now the built-in hob is being prepared for installation, after which it is installed and connected. Gently insert it into the hole and, with a gentle touch of the hands, push it down until the protruding edges are completely attached to the surface of the countertop. Before this, you can apply a layer silicone sealant onto the surface, which is then covered by the built-in hob. This will ensure the sealing of the connection. When pressing on the surface, care should be taken, especially if it is glass. It is important that the built-in panel lies evenly on the surface of the countertop. Otherwise, placing a heavy pan on it may create a breaking force.
   
7. The last stage of installation is that the built-in panel is fixed using special fixing clips included in the kit. The clamps are installed from below, after which the case is fixed. Protruding excess sealant that has been applied to the surface of the countertop must be carefully removed. If an oven is installed under the hob, a layer of thermal insulation is laid between them.
   

The detailed process of installing an electric hob in the countertop is shown in the video tutorials:

Electrical connection

To connect the built-in hob to the mains, it is enough to check the presence of voltage and connect the plug to the socket. When preparing for installation, make sure that the cross section of the wires corresponds to the connected electric power, which the built-in panel has. Otherwise, you need to draw a separate line from the inlet shield to the plate. Then the installation of an outlet may not be required. We talked about it in more detail in a separate article, which we strongly recommend that you read.

I still opted for an induction hob. Because I don’t have gas in the house, but I didn’t want a regular electric one. Panel from the manufacturer HANSA, there will definitely be an article about it, but today is not about that. Today I need to install this hob in the countertop! And I have never done this before, I just saw how the masters do it. But I didn’t really want to pay 2000 - 2500 rubles for installing the surface, and therefore I decided to install it myself, in principle, I succeeded, I think you can too ...

The article will be with pictures, so read and see everything step by step.

Guys for starters. Be sure to read the article, so as not to redo the wiring several times!

1) Tool. For installation (cut-in) hob, we need a jigsaw, a drill, a tape measure, marking pencils and a flat board, about 1 meter (I have furniture left) or a large ruler.

2) We determine the place where we will embed the panel, I have this place above the void for the oven. Of course, the panel can also be embedded above cabinets with dishes and kitchen utensils, but in my opinion this is not very correct.

3) We try on the panel by eye. The main thing is to leave enough space around the edges.

4) Now the most difficult thing is to mark the dimensions on the countertop. To begin with, I determined the center, simply measured the distance (where the installation will be made) and marked the center.

5) Now we take a book, it has everything required dimensions you should try to follow them. To begin with, I define the gaps horizontally. That is, what size should be set aside from the wall and which one should be left to the edge of the countertop. Moreover, these dimensions are already indicated by the manufacturer, here they are in the picture - X and X1. X - 50 mm (to the wall), X1 - 60 mm (to the edge). Set aside these dimensions. I have a corner attached, it is 30 mm, so I set aside another 20 mm from it and that 50 mm. At the end, exactly 60 mm remains, you don’t even need to measure there.

6) Now the dimension “A” is important to us - this is the width of the plate, we have it 560 mm, that is, 280 mm from the center (which we set aside). Draw two parallel lines from the center at a distance of 280 mm. And in the end we get all the sizes. Look here.

7) Now we take a drill, insert a drill 8 - 10 mm (to fit a jigsaw file) and drill. We need to drill three - four holes (three are possible, then the last corner in which we do not drill - we will cut to it). Here are my three holes.

8) Next, we take a jigsaw and begin to cut the countertop, everything is strictly in size. It should be noted the dimensions that are in the instructions already with gaps. You will have to sweat the tabletop is difficult to saw, but after 20 - 25 minutes everything was ready.

9) After that, just take out the cut out plate and remove it.

10) We remove the sawdust and try to insert the panel into place, everything should be fine! They did it according to the size of the manufacturer. The plate moves a little, that is, you can move it a little to the right - to the left, as well as up and down.

Complex stoves for the kitchen, simultaneously combining a hob and an oven, are becoming more and more a thing of the past. Modern housewives are less and less using intended purpose ovens. They are increasingly turning into a warehouse of pots and pans.

Why overpay money for an unnecessary metal cabinet when you can buy a comfortable and aesthetic hob, and the free space formed under it is perfect for storing dishes and other things. Even an inexperienced master can install a hob in a countertop, because its installation does not require experience and qualifications at all.

Varieties of hobs

So, before proceeding with such a procedure as installing a hob into a worktop with your own hands (you can see the photo in this article), you should deal with the varieties of these devices. There are the following main types of hobs:

1. Electrical.
2. Induction.
3. Gas.

It is advisable to entrust the installation and installation of the latter option to a professional, since an incorrect connection can lead to serious problems. When using gas stoves indoors, special requirements must be observed. During installation electrical panels it is also important to observe caution and safety rules when working with high voltage. It is necessary to provide high-quality electrical power with grounding.

When buying a hob, it is important Special attention pay attention to it Since the installation of the hob in the countertop should be carried out with a small margin at the edges. In addition, you need to decide on the location of the tie-in. Spend in advance

Countertop installation

If you have purchased a glass or stone countertop, it is advisable to entrust its installation to professionals. Since you do not know about all the intricacies of the process, you can damage an expensive item. If you can handle the installation yourself, but with some building skills.

You will need the following:

• Grout for tiles.
• Tiles for facing the surface of the countertop.
• Mounting or tile adhesive.
• Tiles with tungsten coating.
• Gun with silicone sealant.
• Electric jigsaw.
• Waterproof wood board.
• A set of tools - a square, a screwdriver, screws.

Replacing the countertop should begin with the dismantling of the old one. Despite the fact that you will not need the old countertop in the future, you must remove it very carefully to avoid damage to the kitchen unit.

It is very important to fit the new countertop to the dimensions of your furniture. It is likely that you will need to cut off the excess. In this case, the unprotected edges of the chipboard are exposed. This material perfectly absorbs moisture, so the cuts must be well treated with a sealant. If the countertop is mounted with saw cuts to the stove, it is advisable to close them with special end strips.

Required Tools

Before proceeding to such a process as installing a hob in a countertop (photos show what they are), you need to prepare the following tools:

• Pencil.
• Roulette.
• Jigsaw.
• Drill driver with a drill for wood with a diameter of 8-10 mm.
• Sealant.

Preparatory process

To begin with, you should make sure that there are accessible outlets in the place where the hob will be installed in the countertop. The presence of an outlet, a suitable length of the gas supply hose, without squeezing and kinks for a gas stove - these are two fundamental aspects.

If the wiring is old and there is no certainty that it is reliable, it is recommended to run an independent cable for the stove directly from the meter.

Installing the hob in the countertop

1. First you need to make a hole in the countertop. To do this, according to the instructions, an opening is marked. If there is no instruction, then
   the full dimension is outlined, while on each side you need to retreat about 5 mm.
2. Using a drill, a hole is drilled so as not to go beyond the contour boundary. Then we continue to work with a jigsaw. To reduce chipping, it is recommended to take a file with fine teeth. In addition, you can paste over the contour with stationery or masking tape.
3. After the drank is completed, you need to paint over or sealant the sawn edges to prevent the countertop from swelling.
4. Next, the hob is installed in a 28 mm worktop, fixed and connected to the network.

Panel insertion must be carried out with maximum precision. Otherwise, even an error of 1 cm can ruin the countertop, which is one of the most expensive elements of a kitchen set.

Countertop made of artificial stone

Compared to their chipboard counterparts, an artificial stone countertop is the most durable. Despite this, the main problem is the installation of the hob in an artificial stone countertop.

In most cases, an artificial stone countertop is ordered with pre-drilled holes for a specific hob. But what if the countertop is already installed, but the hob is not yet? In this case, the most reliable and the best option will give the countertop to qualified specialists who, using a professional tool, will make the necessary hole.

If you still decide to take the risk, then this work can be produced using the technology described above, but only instead of a jigsaw you will need to take an angular grinder and a diamond-coated blade designed for cutting concrete.

It is important to remember that self-installation hob in the countertop should be well thought out at all stages of installation. Only in this case, less time will be spent on this type of work, and their quality and subsequent result will significantly improve.

The hob allows you to not only cook any dish, but also save space. After all, such equipment has smaller dimensions than large and bulky gas stoves. How to install the hob and oven? Everything is simple. The main thing is to follow the instructions. Everyone is able to cope with such tasks. This does not require expensive equipment, but only the presence of certain tools is important.

What will be required

In conclusion

Now you know how to embed the hob in the countertop with your own hands. Before starting work, it is worth evaluating your skills and abilities. If this is not possible for you, then you should seek the help of professionals. However, it is safe to say that the installation process is not very complicated. Practically everyone can cope with such a task. The main thing is to carefully study the instructions and have everything at hand. necessary tools. When performing such work, it is recommended to take into account all the nuances and subtleties of the process.