Spinner at home. How to make a spinner with your own hands without bearing: the best master classes homemade spinner for hands

Spinner is a new funny toy that came to taste to adults and children. She appeared in America last year and for a short time won great popularity. The principle of operation of the toy is simple: Middle and thumb take one hand for the central bearing. With the other hand, refer to the wings of the turntable. With sufficiently good management skills, you can bring the toy into action with one hand. Purchase and thumb take the central bearing. Nand Spinner consists of three parts: housing, bearing and plugs.

Benefits Spinner

1. Motoric has developed, fingers become more sensitive. This tool is very useful for those who have suffered various injuries of the hands.
2. This toy from the kind of antistress, which soothes the nerves. In addition, thanks to her, it is possible to focus, restore performance, remove the excitement and nervousness, and also become less irritable.
3. Spinner will be an excellent companion during a long trip, it can be perfectly taken free time.

LED spinner on controller

Someone buys them, and someone makes them hands. Here schematic scheme Spinner with LEDs controlled by a microcontroller. When rotating, all sorts of pictures and signs are created.

List of project details:

• MK Attiny-45
• 5 SMD LED (1206)
• 5 SMD Resistor (47 Ohm)
• 1 Battery 16 mm (3 V)
• Diameter 22 mm bearing
• Piece of wood or plastic

The scheme as you can see the simplest, but if anyone does not understand - read the datashitis from ATMEL.

Positive LED conclusions go to PB0 - PB4 on MK. For current programming added resistors between them. Negative contacts of LEDs go to minus - GND.

Possible different variants Displaying figures, so the browser page is made to create sequences of images for spinner. In the shared file, the link to which was higher, you will find the drawing, firmware and program.

Spinner on ball bearings

This spinner consists of the housing on bearings and plugs. The central bearing is the most important. The speed and time of rotation of the spoon depends on its quality. The plugs are inserted into the central hole.

One of the most accessible from the remedies is paper and cardboard. From paper Hand Spinner is made using a knife, four bearings, glue. First you need to make drawings. With the help of a stationery knife cut parts from paper or cardboard. Bearing holes are cut with manicure scissors or knife. It is important to look so that their diameter should be slightly smaller than the bearing diameter. It is necessary so that the bearings are tightly entered into the holes. The number of parts depends on the width of the bearing. For gluing you need a lot of glue. It will give the product a greater strength. After completing the work, the toy is painted in any color.

To increase the moment of inertia, it is necessary to provide weights. Most. simple option They are glued together coins. For 10 mm plywood, it is necessary to glue 8 ten-topical coins among themselves. The inner surfaces of the workpiece align with the help of the borders. The outer surfaces gently and quickly bring to the contour with a grinder with a grinding circle. All the remaining irregularities are removing manually by sandpaper.

Those who can work the jigsaw and drill, you can make a spinner of wood. Tree - Ecological Clean Materials. The product is beautiful, pleasant to the touch. First choose solid wood. For beginners it is better to use Phaneur. Skills are needed to work with the tree. First prepare the drawing. It can be thought of it or simply print from the Internet. Paper blank applied to a tree or plywood and put in a pencil. To cut down and polish the detail of sandpaper. The hole can be cut down, but it is better to make a drill so that the hole is smooth. Important moment: Make a drill on one side hole up to half, and then turn the item. So more chances to get the perfect hole for the bearing. The thickness of the tree or plywood should be exactly the same as the bearing. If it is a little more, you need to polish.

Typically use a bearing of skateboard wheels, rollers or scooters. They have standard size The diameter of 22 millimeters, width and inner diameter can be selected at its discretion.

Experimenting with sizes, we came to the conclusion that perfect size For long twist 25-27 mm in diameter. At the same time, for spinner, it is better not to take the bearings less than 20 and more than 30 mm.

Finger Spinner will be the Savior of those people who are nibble, knobs or the like. The turntable is designed to withdraw stress, the warm-up of the fingers, as well as to concentrate the attention and development of the motility of the hands. Such a device will become an indispensable thing for children and adults.

The surface of the materials can be drunk or smooth, in color you can find a variety of options: white, black, red and many others. The dimensions of the toy are small, which allows you to carry it with you. Unusual I. stylish design Can make an excellent accessory from it.

How to make a spinner do it yourself

Why do you need a spinner from the store, if it is mono to do it yourself. The whole process of work will take a little time, and in the design it is simple. In order to start making, you will need:

• Textolite;
• furniture ties;
• bearings;
• drill and drills to her;
• rule, Circle.

First you need to take textolite and cut out the base for spinner. Previously, with the help of a circulation, a drawing of the toy is drawn, and only then cuts out. Before painting the base, you need to know the bearing size, for example, it is 22 mm, respectively, the circulation must be inserted into the textolite for 11 mm and draw a circle. After that, insert a circuit for 18 mm, and draw another circle. For each case, an individual counting is required. Make it just, all the variety of options is presented on the Internet, there are stencils for Spinner.

Then proceed to work with bearings. Each of them needs to wipe the resin, after which you can connect them with BRO. Only after that you can drill holes under the sleeve. To do this, notice the six sectors of the Sport. Each point of intersection of sectors and circles is the center of Gils. You need to drill holes in each intersection, exactly six pieces. Then you need to drive the center of Spinner.

Each sleeve, before inserting into the hole, you need to span. It is very simple to do it, for this it is necessary to insert it into the cartridge of the drill and rub on the sweeping paper on the lowest turns on the sandpaper until all the paint deals with them. Each of the sleeves you need to lubricate all the same resin and to press.

After all actions are made, the toy need dates to dry. This will require at least six hours, after which you can enjoy the game with a spinner for hands.

Video - the most cool spiners

This craft will be dedicated to how to make a spinner with their own hands. The design is quite simple, so much that even the child can do it.

What is spinner? This is an anti-stress toy, developing motility of hands in children and the soothing nerves of adults. That's what you need a spinner for hands. The basis of spinner is the bearing or a rotating core, and on the edges there are weights. Thanks to this design, the entire body can rotate for a long time around its center, and the acceleration can be betrayed with his fingers.

How to make spinner

A key role in creating this toy is a ball bearing. But the materials of which will be made by the case, is not so important. It can be a tree, plastic, paper, cardboard or metal.

How to make spinner at home

By the way, the spinner can be done at all without a housing. Let's consider this option, as the first example, we will make the spinner with your own hands at home from 4 bearings and clamps.

Everything necessary materialsexcept bearings, most likely you already have at home. But the bearing can be removed from old rollers or buy in the sports store. As balancing loads, we will use exactly the same bearings. We will connect them with clamps.

We need:

• 4 bearings
• 9 tiezhek

Connect 3 screeds with each other and in the corners of the resulting triangle place bearings. Make another 3 rings, put them on the design, place another bearing in the center and tightly all the shock. Cut sticking ties and everything, now you know how to make spinner yourself.

But do not forget to pre-clean bearings from oil and dirt. After that, it can be painted into your favorite color.

Easy way to make spinner at home

In this method, we will connect bearings with epoxy resin and colored shoelaces. If you already know how to make a spinner of the bearing, then you will not have difficulties.

What can spinner do from:

• 4 bearings
• epoxy resin
• sandpaper
• colored shoelaces
• feltolsters

First of all, open one bearing and remove the lubricant. With the help of sandpaper, sand the metal that needs to be glued together. Prepare epoxy and apply it to ends. Add a little resin from above and let dry.

In order to decorate your spinner, you can use multi-colored laces.

Apply some glue or epoxy resin on the lace and cross the anti-stress toy.

With the help of felt-tippers, you can decorate Spinner in any favorite color.

How to make a spinner of one bearing

It is not necessary to use 4 bearings, it is done for aesthetic beauty. The main rule when creating a manual twist is symmetrically located at the edges of the weights.

You can use conventional bolts or nuts as weights. The washer is used as a stand to accidentally not glue the design to the table.

Draw a circle and draw three diagonal lines. In the center of the circle, place the bearing, and glue the bolts to the three sides using a superclay or epoxy resin.

Now you know how to make a spinner with your own hands from the bearing and bolts. By the way, such a design turned out to be the most successful, thanks to the long bolts, the spinner spins very long.

As you can see, everything is very simple and there is no need to immediately run to the store for a new toy. Now you know 3 simple ways to make a spinner in 5 minutes.

How to make a paper spinner

The principle you understood. Therefore, you can now boldly make this fun toy from anything. As a case, we will use cardboard or paper, and the weights will be ordinary ruble coins.

How to make a spinner of paper without bearing

In this example, the bearing does not need us. It can be replaced by a wand or a wooden spanch, around which Finger Spinner will rotate.

It will take:

• Cardboard
• Paper
• Coins 6pcs.
• Adhesive gun.
• PVA glue (you can only do the adhesive gun or super-glue)

The detailed process is shown in the video.

As you can see a new-fashioned turntable toy can be made almost from anything. Share in the comments What ways you know!

Spinners entered the mass fashion not so long ago, but in just a few months they conquered the hearts not only adults, but also children. Today, the spinners are spinning everywhere: on the street, at work, in the subway and even in children's garden! And every child wishes his toy something different from those who already have peers. You can buy the original spinner, but it is worth such a toy is not cheap, and the search for a unique spinner takes a lot of time. The best decision - Make a spinner yourself.

So, we bring to your attention a few simple ways How to make a spinner with your own hands from the materials that every home has.

1. How to make spinner from plastic covers?

Materials: Looks from any plastic bottles of the same size (4 pcs), plasticine, thermoclay, nail, scissors, lighter and toothpick.

What do we have to do: Put the plasticine in 3 covers, with the help of a thermoclause, creep the remaining space of the covers. Take the fourth cap (without plasticine) and make a hole in it, for example, heated nail. Stick the lids with sand to the one where you just did a hole. Take the glue rod and cut 2 small pieces from it (1 cm). Felt in half to the toothpick and wear a piece of glue to her end (watch the sharp tip of the toothpick sticking) and place it in the center of your future spinner. From the opposite side to the tip of the toothpick put on the remaining piece adhesive rod. Your spinner is ready!

For more interesting view, you can paint the caps in different colors Acrylic paints.

2. How to make a spinner of cardboard?

Materials: Looks from plastic bottles, cardboard, scissors, marker, sewn or manicure scissors, glue, 3 coins and rods from the handle.

What do we have to do: With the help of the covers, draw 4 circles on cardboard in the form of your future spinner. After that, cut out 5 such blanks and glue them with each other, carefully smoking the edges. Next, cut out a smaller circle. Using sewn or thin manicure scissors Make a hole in the center of Spinner. On the sides of the billets, glue 3 coins or any stickers.

Next, take a pending handle rod and carefully cut 1 cm from it. Make small holes in the center on two small circles. Sliced \u200b\u200bpiece from the handle rod insert into one of the circles and glue it along the edges of the hole to secure it to securely. Slide this circle to the center of your spinner and get the second circle from the reverse side. The two remaining small circles can be glued on top of the tips of the rod. So that your spinner spinning faster, put some gasket between the workpiece of the spinner itself and small circles (in our example we used metal suspensions).

Ready! Let the child decorate his spinner as he wants, you can use sparkles, stickers, rhinestones and other decorations.

3. How to make a spinner using bearings?

Materials: Bearings (3 pieces), screed clamps, adhesive gun or superchalter (for more complex spinner).

What do we have to do: Cut the bearings from all sides with cable ties. Cut extra clamps and all - the spinner is ready!

To be more bright and attractive, you can make the design more complicated. Take 7 bearings, 6 of them post around the seventh. You will not use all 7 bearings, you will need only 3 circular and 1 central. The rest of the bearings are needed to you only for accurate measurement, so we will only leave those that form a triangle. Stick all the necessary parts with adhesive pistol or superclaud. Spinner is ready! Decorate Spinner as you want. You can stick a fluffy wire, apply glue on the sides of the spinner and fall asleep the edges of sparkles.

Be sure of such spinners, like your child, will not have anyone!

How to make a spinner with your own hands at home? - this question is interested in very many. And it is not surprising, today there is a real boom with spinners. Everyone knows about them, and everyone wants to twist it. But the prices of normal spinners are puzzled by the fact that a piece of material and bearings are so much worth so much. There is always a way out - make a spinner with your own hands.

Honestly, at first I generally thought that the spinner was some kind of spinning toy for cats, and just recently interested, what is it and how to make spinner himself.

The choice fell on classic models Three-Spinner, whose bearing and center and on each petal. Bearings on the edges are needed rather as weighting agents, twist, holding for them not so interesting, and depending on the size of the spinner, not all of all the length of the fingers.

Bearing for Spinner

So, to make a high-quality spinner, with your own hands, you will first need to get the bearings. Cheap spiners are most often made without bearings, which is somehow not ice. You can cut from cardboard, and turn on the rod from the handle, but we want everything to be on Feng-Shui).

Most often used bearing indicated as 608. This is not some kind magic number, but simply the bearing brand, there are 607 (less) and 609 (more). The 608th bearing has an outer diameter of 22 mm, and internal - 7 mm. Thick is 8 mm.

It is used most often on the anchor of motors of perforators and electric drills. Well, it was found in one of the car shops. In the same place, by the way, with me, the perforator was revealed.

Each bearing was packed in a bag and a small box, arguing that he was made in Russia. But then it turned out from a familiar seller, the inscription "Made in Russia", as a rule, says that he is Chinese ... (Clarification - I live in Tashkent, Uzbekistan, so I do not know how things are in Russia)

Quality bearing - very important element Spinner, because It depends on how long the spinner will spin, and how stable it will be. Therefore, later the bearings were replaced with similar Korean.

Good bearings, but smaller size (15 mm in diameter and 5mm thick) were used in old hard disks. The speed of rotation of the hard generation was 5400 rpm, and the modern 7200 rpm. In modern hardhas, the bearing is in the engine and has even smaller sizes. On such a bearing, you can make a good high-turn spinner that can spin very long time.

Preparing Bearings for Spinner

Bearings are sold closed dustproof rings and lubricated. For spinner, no lubricant is required, it will only pack your hands and slow down the rotation of its viscosity. Therefore, the lubricant must be deleted. This will require 50-100ml of gasoline.

We disseparable bearings, removing dust-proof rings with something sharp and thin. We throw bearings in a jar and fill with gasoline. We leave them in gasoline for several minutes, then chatting a jar, so that the bearings have stuck. The perch of unnecessary toothbrush into gasoline, remove the residues of lubrication from bearings.

To get rid of the smell of gasoline, you can wash the bearings with soap, using the same toothbrush. If you wish, you can insert back dustproof rings, but I like the combination of wood and metal more. Now bearings are fully prepared for use in spinner.

Material for spinner

The material was chosen plywood as the most convenient during processing. You can also cut out of a thick sheet of gethinaks or plexiglas, but it is easily scratched, so it is difficult to do neatly. In the bins of the house there was a piece of 10 mm plywood, from some killed Soviet tape recorder.

I did the markup using the circus, line, the transport and pencil. It is important to make a very accurate markup, otherwise then the center of the mass can shift and the spinner when rotating will beat. It is more convenient to print a pattern of paper, cut and circle, it will save both time and nerves.

Production of Spinner housing

Because was chosen classic curved shape, 19mm crown was used to cut the internal rounds and holes for bearings. Better, of course, use 20 or 21 mm, but I was simply not able to find it on sale.

The crown has a special holder in which the drill is inserted for the center. Before driving large holes, in the centers of future holes it is better to drill guides of a smaller diameter, and then fixing the crown in a drill, drills 6 large holes in a circle and one central.

The crowns on the tree have a fairly large teeth. They can easily wear upper plywood layers. Therefore, if you decide to make a spinner with your own hands from plywood, it is better to drill up to the middle first on the one hand, and then on the other.

Drink the body of Spinner

Now we spill extra, each petal. For this, the jigsaw was used, but it is possible to the usual hacksaw. We try to suck as close as possible to the markup, so that later I had to get better.

Rarsing holes for bearings

In addition to the outer part of the case, internal, i.e. need Holes for bearings. They turned 3 mm less required. Using a round file and focusing on the markup, we melt the holes so that each bearing is very tight. Better, of course, all this is done by the machine, if you have it.

Customize the spinner in thickness and whisch

After how everything was crushed and sharpened, it was time to bring the found pilher to the thickness of the bearings, i.e. 8mm instead of 10. For this, with each of the side of the workpiece, it was removed along the layer of plywood and it became exactly 8 mm thick. Further, the entire workpiece was extracted first large, and then shallow sandpaper.

Finished design:

Holder for fingers

By inserting bearings and twisting, it was decided to make a finger holder. When the holes are dried, there are holey rounds, which just went to this matter.

A sharp knife, a column was cut from the tail, along the inner diameter of the bearing. Rounds were trimmed in layers up to 3. The ends of the column with a file were rapidly so that there are tight rigs. This is how the composite parts of the holder look like:

It remains only to insert the holder into the central bearing, pre-missing the places of compounds with glue and waiting for a complete drying to rejoice new toy - Spinner made by hand)

Now you know how to make a spinner with your own hands - the thing is quite useless, but cool.

Write all questions in the comments

Does your child succumbed to the mass fashion for the spinner twist? Requests himself red, yellow, and still luminous and in the form of minion? In general, not like everyone else? Then you can make a toy with your own hands. Moreover, such a work lesson will take you, and your baby. And if you still do not know what a spinner is -, there we answered all popular questions about this modern arms for fun.

We have collected for you three ways to make a spinner, two lungs and one - more complicated (there will be a help of Pope). But, we are confident that the tools and materials should be found at home or in the country. Each instruction is supported by a video lesson found on YouTube for clarity. So, how to make a spinner of paper, from plastic covers and from wood?

Method 1. Spinner of paper and cardboard.

Just, cheap and very not even angrily - paper spinner for beginner spinnerodels. Older child will handle himself, kid may need small helpAnd the result can be proud to attribute to the garden or school - there is always a creative in honor.

What do you need:

• Cardboard, marker and lid (or ready-made template from the Internet)
• Scissors
• Manicure scissors or awl
• 3 coins
• Rod from handle
• Paints or sequins for decoration

Instruction:

1. Download the ready-made spinner pattern from the Internet. Or draw it yourself by going covers from plastic bottle on cardboard. You need to cut two blanks from cardboard in the form of spinner.
2. Cut more four more smaller circles. You can circle a coin of less dignity.
3. Start three coins of suitable size on the sides of one of the cardboard blanks.
4. Stick from above to the workpiece with coins, the second half.
5. Manicure scissors or seer Make a hole in the center of Spinner.
6. Cut about 1 centimeter from the rod from the handle.
7. In two small circles, do holes in the center.
8. You can paint the finished blank of the Sport in any colors or decorate it with sequins, rhinestones or stickers with your favorite heroes of the child. All about your choice and completely unique!
9. Insert a piece of the rod into one of the small circles and glue it along the edges of the hole.
10. Slide the circle with the rod to the center of Spinner and stick the second circle on the other side.
11. Stick two remaining small mugs on top of the ends of the rod. Ready! The spinner of cardboard, without bearing and with full blows of fantasy in terms of design, will necessarily take a child for a while.

A source: Plastilin.

Method 2. Spinner of plastic covers.

This spinner will require a little more materials and zeal, but also will last an order of magnitude longer. In general, the spinner of caps from under Coca-Cola is approximately as crafts from matching boxes For older generations. Cute heart consumables and heating soul the result with minimal for actively functioning (that is, spinning) things.

What do you need:

• Covers from plastic bottles
• Kinetic sand or plasticine
• Glue gun
• Nail and lighter
• Adhesive rod.
• Scissors
• Toothpick

Instruction:

1. In three covers from bottles, put almost to the top of the kinetic sand or plasticine. The main thing is to drain the blades.
2. The glue-gun fill the space left in the covers to the top.
3. In the fourth (without sand), make a hole (you can with a heated nail).
4. Stick three covers with sand to the central lid with a hole.
5. Cut two pieces of approximately 1 centimeter from the adhesive rod.
6. Break in half toothpicks. Put on one end a piece of the rod (the toothpick should not stick together) and the gross to the center of Spinner.
7. Put the second piece of the rod on the tip of the toothpick on the other side. Ready! If there is a great zeal, such a spinner can also be created creatively - paint (for example, acrylic) or punctured something positive. And you can leave and as it is, choosing interesting combinations Bottled drinks.

A source: Chip day.

Method 3. Spinner of wood (with bearing)

Go to the most time consuming method of manufacturing spinner. Here, without parents, it is not necessary to do, but the result can be safely lay out on the desk together with purchased toys. Again, in terms of design, freedom is provided for self-expression. For those dads and children that they are friends with the jigsaw, you know how to find the bearings on the shelves and know how to keep the drill.

What do you need:

• Bearing for 2 mm
• Plywood Leaf (5 mm)
• Stack of coins
• Scissors
• Pencil
• Manual Lobzik
• Sandpaper
• Template (or cardboard and marker for its creation)
• Clamp
• Drill

Instruction:

1. Stick the template on the plywood sheet and tick the place for future holes in each of the circles.
2. Drill holes in each of the three mugs on the sides, so that it was more convenient to cut them out.
3. Grind the jigsaw to the holes and drink them.
4. Drink the billet from the sheet of plywood itself and put it with its sandpaper.
5. You can paint the spinner to any color you like.
6. Grind the bearing to the central circle, if it is bad, you can drive it there with a hammer.
7. Slide the stack of coins for internal circles. Start with a five-book coin (put it under the circle), hereinafter - bubble and from above again coin with a nominal five rubles.
8. Make it for all circles. You can decorate it from above at will. Ready! Just think how much benefits from homemade anti-stress toys: they spent a good time with the child together, they worked out nicely and saved on the purchase of another plastic trough. And he turns perfectly!