Doors wooden external for inhabited and. Wooden exterior doors for residential and public buildings

The standard applies to wooden exterior swing doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises in various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: stations, theaters, museums, sports palaces, exhibition pavilions, palaces of culture.

Doors manufactured according to the standard, depending on the purpose, are divided into the following types:

H - entrance and vestibule;

C - service;

L - hatches and manholes.

Type H doors must be manufactured with panel and frame sheets. Frame cloths can be swinging. Doors of types C and L must be made with panel panels. Panel boards can be made with slatted sheathing.

Doors of H and C types are produced with single-leaf and double-leaf, glazed and blind leaves, with and without a threshold.

All doors manufactured according to the standard are doors of increased moisture resistance.

dimensions doors must correspond to those indicated in Fig. 12. The dimensions in the drawings are given for unpainted products and parts in mm. The dimensions of the openings are shown in Fig. 25.

By agreement between the consumer and the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as using blind sheets.

Doors of type C can also be doors with solid filling and a reinforced frame in accordance with GOST 6629-74.

The following structure is set symbol(brands) of doors.

Examples of symbols:

entrance door or tambour single-leaf door for an opening 21 dm high and 9 dm wide, glazed, with a right hinged panel sheet, with a threshold, with type 2 cladding:

DN 21-9PShchR2 GOST 24698-81

the same, with the left hinge of the frame canvas:

DN 21-9LP GOST 24698-81

entrance door or tambour door with swinging canvases for an opening 24 dm high and 15 dm wide:

DN 24-15K GOST 24698-81

service door, two-leaf, blind, for an opening 21 dm high and 13 dm wide, insulated:

DS 21-13GU GOST 24698-81

single-floor hatch for an opening with a height of 13 and a width of 10 dm:

DL 13-10 GOST 24698-81

The design, shape and dimensions of the doors must correspond to those indicated in Fig. 13 - 16, and the dimensions of the sections - in hell. 17 - 24.

Crap. 12. Dimensions of doors

Notes:

1. Door schemes are shown from the side of the facade.

2. The numbers above the door diagrams indicate the dimensions of the openings in dm.

3. Dimensions in parentheses are for doors 21-15A, 21-19, 24-15A and 24-19 with swinging leaves.

4. Doors 21-9 and 21-13A are provided for one-story buildings and waste collection areas.

Design, shape and sizes of doors

Crap. 13. Panel doors

Sections of parts, see Fig. 17 - 19.

This standard applies to wooden external hinged doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises in various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: stations, theaters, museums, sports palaces, exhibition pavilions, palaces of culture.

1. TYPES, SIZES AND GRADES

1.1. Doors manufactured according to this standard, depending on the purpose, are divided into the following types:
H - entrance and vestibule;
C - service;
L - hatches and manholes.

1.2. Type H doors must be manufactured with panel and frame sheets. Frame cloths can be swinging. Doors of types C and L must be made with panel panels. Panel boards can be made with slatted sheathing.
Doors of H and C types are produced with single-leaf and double-leaf, glazed and blind leaves, with and without a threshold.

1.3. All doors manufactured in accordance with this standard are classified as doors of increased moisture resistance.

1.4. The overall dimensions of the doors must correspond to those indicated in Fig. 1. The dimensions in the drawings of the standard are given for unpainted products and parts in mm. The dimensions of the openings are given in reference appendix 1.
By agreement between the consumer and the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as using blind sheets.
Door leaves of type C, upholstered on both sides with thin-sheet galvanized steel according to GOST 7118-78, have dimensions of 6 mm in width and 5 mm less in height than those of leaves without upholstery.
Doors of type C can also be doors with solid filling and a reinforced frame in accordance with GOST 6629-74.

1.5. The following structure of the symbol (brand) of doors is established.

Examples of symbols:

Entrance door or tambour single-leaf door for an opening 21 dm high and 9 dm wide, glazed, with a right hinged panel sheet, with a threshold, with type 2 cladding:

DN 21-9PShchR2 GOST 24698-81

the same, with the left hinge of the frame canvas:

DN 21-9LP GOST 24698-81

entrance door or tambour door with swinging canvases for an opening 24 dm high and 15 dm wide:

DN 24-15K GOST 24698-81

service door, two-leaf, blind, for an opening 21 dm high and 13 dm wide, insulated:

DS 21-13GU GOST 24698-81

single-floor hatch for an opening with a height of 13 and a width of 10 dm:

DL 13-10 GOST 24698-81

2. DESIGN REQUIREMENTS

2.1. Doors must be manufactured in accordance with the requirements of GOST 475-78, this standard and according to working drawings approved in the prescribed manner.

2.2. The design, shape and dimensions of the doors must correspond to those indicated in Fig. 2 - 5, and the dimensions of the sections - to hell. 6 - 13.

2.3. Sheets of panel doors should be made with solid filling of the panel with wooden slats calibrated in thickness.

Door cladding is made with materials in accordance with GOST 475-78 in the part related to doors of increased moisture resistance.

Provided continuous door trim with outer side profiled laths in accordance with GOST 8242-75 on a layer of glassine in accordance with GOST 2697-75 or galvanized steel sheathing in accordance with GOST 7118-78, it is allowed to use hard fiber boards of the T-400 grade in accordance with GOST 4598-74 or plywood of the FK grade in accordance with GOST 3916-69. Tambour doors are allowed to be made without sheathing with wooden slats. The rails are fastened with screws according to GOST 1144-80 or nails according to GOST 4028-63 40 mm long with anti-corrosion coating. The maximum fastening pitch is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

2.4. The lower parts of the H-type door leafs must be protected with wooden planks 16 - 19 mm thick or strips of decorative paper laminate 1.3 - 2.5 mm thick according to GOST 9590-76, superhard fiberboards 3.2 - 4 mm thick according to GOST 4598 -74, thin sheet galvanized steel. Wood and plastic protective materials fasten waterproof glue and screws with anti-corrosion coating, and steel strips - screws 30 - 40 mm long in accordance with GOST 1144-80. Mounting pitch around the perimeter 100 mm. The dimensions of the protective strips and strips are indicated in Fig. 6 - 11.

2.5. Cloths and frames of fire-retardant and insulated doors of type C should be protected with thin-sheet galvanized steel 0.35 - 0.8 mm thick according to GOST 7118-78 over the entire surface on both sides, as indicated in Fig. 12. Sheets of steel are interconnected in a single fold.

2.6. Cloths of fireproof doors of type C are covered on both sides with layers of asbestos cardboard 5 mm thick in accordance with GOST 2850-75.

Cloths of insulated doors of type C are covered on one side with a layer of soft fiber boards 12 mm thick in accordance with GOST 4598-74. Along the perimeter of the canvas from the insulation side, they are fixed with nails or screws. wooden slats 12 30 mm, fastening pitch 100 - 150 mm.

2.7. Used for glazing doors window glass 4 - 5 mm thick according to GOST 111-78.
If the glass is 800 mm or less from the bottom of the curtain, and when using large format glass, safety guards must be installed.
Examples of installation of protective fences are given in the recommended appendix 2.
The glass thickness, the design of protective grilles and changes in the design of doors associated with the installation of electric locks must be indicated in the working drawings.

2.8. For protection against mechanical damage to reduce noise and heat loss, type H doors must be equipped with ZD1 type door closes in accordance with GOST 5091-78, sealing gaskets in accordance with GOST 10174-72 or from porous rubber in accordance with GOST 7338-77, door stops of the UD1 type in accordance with GOST 5091-78. In double-leaf doors, latches ZT or latches ShV should be installed in accordance with GOST 5090-79.

2.9. The need to equip doors with locks according to GOST 5089-80 must be specified in the order.

2.10. The location of the devices and their types are given in mandatory Appendix 3.

2.11. The door purchase order must specify:
the number of doors by brand and the designation of this standard;
type and color of finish;
glass thickness;
instrument specification.

DOOR OVERALL DIMENSIONS

Notes:

1. Door schemes are shown from the side of the facade.
2. The numbers above the door diagrams indicate the dimensions of the openings in dm.
3. Dimensions in parentheses are for doors 21-15A, 21-19, 24-15A and 24-19 with swinging leaves.
4. Doors 21-9 and 21-13A are provided for one-story buildings and waste collection areas.

DESIGN, SHAPE AND DIMENSIONS OF DOORS

Panel doors

Sections of parts, see Fig. 6 - 8.

Frame doors

Sections of parts, see Fig. 9.

Crap. 3

Sections of parts, see Fig. 10.

Frame doors with swinging leaves

Fireproof and insulated panel doors

Hatches and manholes

Sections of parts, see Fig. 11 - 13.

SECTIONS OF DOOR PARTS

GOST 24698-81
Group Zh32

INTERSTATE STANDARD

EXTERIOR WOODEN DOORS FOR RESIDENTIAL AND PUBLIC BUILDINGS
Types, design and dimensions
Wooden external doors for residential and public buildings. Types, structure and dimensions

MKS 91.060.50
OKP 53 6110; OKP 53 6196

Introduction date 1984-01-01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the State Committee for Civil Engineering and Architecture under the Gosstroy of the USSR

2. APPROVED AND PUT INTO EFFECT by the Decree of the State Committee of the USSR for Construction Affairs dated 31.04.81 * N 51
________________
* Corresponds to the original. Date of adoption of the standard 04/13/81 (official publication, M .: Standards Publishing House, 1981). - Database manufacturer's note.

3. INTRODUCED FOR THE FIRST TIME

4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS

	Item number, applications
GOST 111-2001

GOST 1144-80
GOST 2697-83
GOST 2850-95	2.2, 2.5, 2.6
GOST 3916.1-96
GOST 3916.2-96
GOST 4028-63
GOST 4598-86
GOST 5087-80	2.2, appendix 3
GOST 5088-2005	2.2, 2.4, appendix 3
GOST 5089-2003
GOST 5090-86	2.8, appendix 3
GOST 5091-78	2.8, appendix 3
GOST 7338-90
GOST 8242-88
GOST 9573-96
GOST 9590-76
GOST 10174-90

5. REPUBLICATION. October 2009

This standard applies to wooden external hinged doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises in various sectors of the national economy.
The standard does not apply to the doors of unique public buildings: stations, theaters, museums, sports palaces, exhibition pavilions, palaces of culture.

1. TYPES, SIZES AND GRADES

1.1. Doors, depending on the purpose, are divided into types: H - entrance and vestibule; C - service; L - hatches and manholes.

1.2. Type H doors must be manufactured with panel and frame sheets. Frame cloths can be swinging. Doors of types C and L must be made with panel panels. Panel boards can be made with slatted sheathing.
Doors of H and C types are produced with one- and two-leaf, glazed and blank canvases, with and without a threshold.

1.3. All doors are classified as products of increased moisture resistance.

1.4. The overall dimensions of the doors must correspond to those indicated in Fig. 1. The dimensions in the drawings are given for unpainted products and parts in millimeters. The dimensions of the openings are given in Appendix 1.

Damn.1. Door dimensions

Door dimensions

Damn.1

Notes:

1. Door schemes are shown from the side of the facade.

2. The numbers above the door schemes indicate the dimensions of the openings in decimeters.

3. Dimensions in parentheses are for doors 21-15A, 21-19, 24-15A and 24-19 with swinging leaves.

4. Doors 21-9 and 21-13A are provided for one-story buildings and waste collection facilities.

By agreement between the consumer and the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as using blind sheets.
Door leafs of type C, upholstered on both sides with thin-sheet galvanized steel according to specifications for steel of a particular type, have dimensions of 6 mm in width and 5 mm less in height than for door leaves without upholstery.
Doors of type C can also be doors with solid filling and a reinforced frame in accordance with GOST 6629.

1.5. The following structure of the symbol (brand) of doors is established:

Legend Examples
Entrance door or tambour single-leaf door for an opening 21 dm high and 9 dm wide, glazed, with a right hinged panel sheet, with a threshold, with sheathing type O-2:

DN21-9 PSCHO2 GOST 24698-81

The same, with the left hinge of the frame canvas:

DN21-9LP GOST 24698-81

The same, with swinging canvases for an opening with a height of 24 and a width of 15 dm:

DN24-15K GOST 24698-81

Service door, two-leaf, deaf for an opening 21 dm high and 13 dm wide, insulated:

DS21-13GU GOST 24698-81

Single-floor hatch for an opening 13 dm high and 10 dm wide:

DL13-10 GOST 24698-81

2. DESIGN REQUIREMENTS

2.1. Doors must be manufactured in accordance with the requirements of GOST 475 and this standard according to working drawings approved in the prescribed manner.

2.2. The design, shape and dimensions of the doors must correspond to those indicated in Fig. 2-5, and the dimensions of the sections - in Fig. 6-13.

Devil 2-5. Design, shape and sizes of doors

Design, shape and sizes of doors

Damn.2

Sections of parts - in Fig. 6-8.

Damn.3

Sections of parts - in Fig.9.

Damn.4

Sections of parts - in Fig.10.

Frame doors with swinging leaves

Damn.5

Sections of parts - in Fig. 11-13.

Devil 6-13. Sections of door details

Sections of door details
Type H
Panel doors

1 ; 2 - cladding with fiberboard grades ST or T-B thick 3.2-5 mm according to GOST 4598 ; 3 - rail 12x12 mm; 4 - gasket made of porous rubber 2 mm thick according to GOST 7338; 5 - screw 1-3x30 according to GOST 1144 , step 200 mm;6 - mounting board

Notes:

1. The use of plastic layouts is allowed.

2. It is allowed to use mounting boards of a different design.

1 - cladding of fiberboard grades ST or T-V with a thickness of 3.2-4 mm according to GOST 4598; 2 - sealing gasket according to GOST 10174

1 - sealing gasket according to GOST 10174; 2 - lining of fiberboard grades T, T-S, T-P and T-SP of group A with a thickness of 3.2-4 mm in accordance with GOST 4598 ; 3 - sheathing brand O-3 according to GOST 8242; 4 - glassine according to GOST 2697; 5 - cladding of fiberboard grades ST or ST-S with a thickness of 3.2-4 mm in accordance with GOST 4598 ; 6 - layout 19x13 mm
Damn.8

Type H

1 - sealing gasket according to GOST 10174 ; 2 - connections on glues of the increased water resistance; 3 - screw 1-3x40 according to GOST 1144, pitch 200 mm; 4 - gasket made of porous rubber 2 mm thick according to GOST 7338 ; 5 - rail 12x20 mm; 6 - mounting board

1 - sealing gasket according to GOST 10174

1 - spring loop according to GOST 5088; 2 - laminated paper according to GOST 9590; 3 - mounting board

Type C

1 - foam rubber gasket according to GOST 7338 ; 2 3 - cladding of fiberboard grade ST or T-V 4 mm thick according to GOST 4598 ; 4 - asbestos cardboard according to GOST 2850; 5 - soft fiberboard brand M-1 12 mm thick according to GOST 4598; 6 - wooden lath 12x30 mm; 7 - screws 1-4x40 GOST 1144, pitch 200 mm

Type L

1 - sheet steel galvanized with a thickness of 0.5 mm; 2 - handle-bracket RS in accordance with GOST 5087; 3 - boards; 4 - mineral wool boards on a synthetic binder in accordance with GOST 9573 ; 5 - gasket made of porous rubber 6x20 mm according to GOST 7338; 6 - loop PN1-130 according to GOST 5088; 7 - wooden stop 50 mm thick

2.3. Sheets of panel doors should be made with solid filling of the panel with wooden slats calibrated in thickness.
Doors are lined with materials in accordance with GOST 475 in the part related to doors of increased moisture resistance.
Under the condition of continuous sheathing of doors from the outside with profile rails in accordance with GOST 8242 on a layer of glassine in accordance with GOST 2697 or sheathing with galvanized steel in accordance with specifications for steel of a specific type, it is allowed to use solid fiberboard grades T or T-S, T-P, T-SP according to GOST 4598 or waterproof plywood grade FK according to GOST 3916.1 or GOST 3916.2. Tambour doors are allowed to be made without sheathing with wooden slats. The rails are fastened with screws according to GOST 1144 or nails according to GOST 4028 40 mm long with an anti-corrosion coating. The maximum fastening pitch is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

2.4. The lower parts of the H-type door leafs must be protected with wooden planks 16-19 mm thick or strips of decorative paper laminate 1.3-2.5 mm thick according to GOST 9590*, superhard fiberboard 3.2-4 mm thick according to GOST 4598, thin-sheet galvanized steel. Wood and plastic protective materials are fastened with waterproof glue and screws with an anti-corrosion coating, and steel strips are fastened with screws 30-40 mm long according to GOST 1144. The fastening pitch along the perimeter is 100 mm. The dimensions of the protective strips and strips are indicated in Fig. 6-11.
________________
* Since January 1, 2010, the use in the territory has been discontinued Russian Federation(here and below).

2.5. Cloths and frames of fire-resistant and insulated doors of type C should be protected with thin-sheet galvanized steel 0.35-0.8 mm thick according to specifications for steel of a particular type over the entire surface on both sides, as indicated in Fig. 12. Sheets of steel are interconnected in a single fold.

2.6. Cloths of fireproof doors of type C are covered on both sides with layers of asbestos cardboard 5 mm thick in accordance with GOST 2850.
Cloths of insulated doors of type C are covered on one side with a layer of soft fiberboard 12 mm thick in accordance with GOST 4598. Along the perimeter of the leaf from the insulation side, wooden slats 12x30 mm are fastened with nails or screws, the fastening pitch is 100-150 mm.

2.7. For glazing doors, window glass with a thickness of 4-5 mm is used according to GOST 111.
If the glass is at a distance of 800 mm or less from the bottom of the curtain and when using large format glass, protective guards must be installed.
Examples of installation of protective fences are given in Appendix 2.
The glass thickness, the design of protective grilles and changes in the design of doors associated with the installation of electric locks must be indicated in the working drawings.

2.8. To protect against mechanical damage, reduce noise and heat loss, type H doors must be equipped with ZD1 type door closes in accordance with GOST 5091, sealing gaskets in accordance with GOST 10174 or made of cellular rubber in accordance with GOST 7338, door stops of the UD1 type in accordance with GOST 5091. gate valves ZT or latches ШВ in accordance with GOST 5090.

2.9. The need to equip doors with locks in accordance with GOST 5089 must be specified in the order.

2.10. The location of devices and their types are given in Appendix 3.

2.11. The door purchase order must specify:
- the number of doors by brand and the designation of this standard;
- type and color of finish;
- glass thickness;
- specification of devices.

APPENDIX 1 (informative). DIMENSIONS OF DOOR OPENINGS IN THE WALLS

ANNEX 1
Reference

Type H

Note. In parentheses are the dimensions of the openings for swing doors.

1 - hardwood planks; 2 - steel bar; 3 - fastening plate made of strip steel

1 - door closers ZD1 according to GOST 5091 ; 2 - hinges PN3-130; PN1-150, PN2-150, PN3-150 according to GOST 5088; 3 - valve ZT or latches ШВ in accordance with GOST 5090; 4 - handle-bracket according to GOST 5087

1 - a loop for a counterbalance; 2 - handle-bracket according to GOST 5087; 3 - holes for M5 screws; 4 - loops PN1-130 according to GOST 5088; 5 - wooden stop

Notes:

1. Closers are not installed in type C doors.

2. Locks are installed in the cases provided for by the working drawings.

3. Pull handles can be installed vertically or horizontally.

4. Loops for counterweight are installed in single-floor hatches. The use of loops of a different design is allowed.

ROSSTANDARD FA for technical regulation and metrology
NEW NATIONAL STANDARDS: www.protect.gost.ru
FSUE STANDARTINFORM provision of information from the database "Products of Russia": www.gostinfo.ru
FA FOR TECHNICAL REGULATION"Dangerous goods" system: www.sinatra-gost.ru

INTERSTATE STANDARD

EXTERIOR WOODEN DOORS FOR RESIDENTIAL
AND PUBLIC BUILDINGS

Types, design and dimensions

Wooden external doors for residential and public buildings.
Types, structure and dimensions

GOST
24698-81

Introduction date 01.01.84

This standard applies to wooden external hinged doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises in various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: stations, theaters, museums, sports palaces, exhibition pavilions, palaces of culture.

1. TYPES, SIZES AND GRADES

1.1. Doors, depending on the purpose, are divided into types: H - entrance and vestibule; C - service; L - hatches and manholes.

Doors of H and C types are produced with one- and two-leaf, glazed and blank canvases, with and without a threshold.

1.3. All doors are classified as products of increased moisture resistance.

1.4. The overall dimensions of the doors must correspond to those indicated in Fig. . The dimensions in the drawings are given for unpainted products and parts in millimeters. The dimensions of the openings are given in the appendix.

By agreement between the consumer and the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as using blind sheets.

Door leafs of type C, upholstered on both sides with thin-sheet galvanized steel according to specifications for steel of a particular type, have dimensions of 6 mm in width and 5 mm less in height than for door leaves without upholstery.

Doors of type C can also be doors with solid filling and a reinforced frame in accordance with GOST 6629.

1.5. The following structure of the symbol (brand) of doors is established:

Legend Examples

Entrance door or tambour single-leaf door for an opening 21 dm high and 9 dm wide, glazed, with a right hinged panel sheet, with a threshold, with sheathing type 0-2:

DN21-9 PShch02 GOST 24698-81

The same, with the left hinge of the frame canvas:

DN21-9LP GOST 24698-81

The same, with swinging canvases for an opening with a height of 24 and a width of 15 dm:

DN24-15K GOST 24698-81

Service door, two-leaf, deaf for an opening 21 dm high and 13 dm wide, insulated:

DS21-13GU GOST 24698-81

Single-floor hatch for an opening 13 dm high and 10 dm wide:

Doors are lined with materials in accordance with GOST 475 in the part related to doors of increased moisture resistance.

Under the condition of continuous sheathing of doors from the outside with profile rails in accordance with GOST 8242 on a layer of glassine in accordance with GOST 2697 or sheathing with galvanized steel in accordance with specifications for steel of a specific type, it is allowed to use solid fiberboard grades T or T-S, T-P, T-SP according to GOST 4598 or waterproof plywood grade FK according to GOST 3916.1 or GOST 3916.2. Tambour doors are allowed to be made without sheathing with wooden slats. The rails are fastened with screws according to GOST 1144 or nails according to GOST 4028 40 mm long with an anti-corrosion coating. The maximum fastening pitch is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

__________

* Since January 1, 2010, the use on the territory of the Russian Federation has been discontinued (hereinafter).

Cloths of insulated doors of type C are covered on one side with a layer of soft fiberboard 12 mm thick in accordance with GOST 4598. Along the perimeter of the canvas, from the insulation side, wooden slats are fastened with nails or screws 12 ´ 30 mm, fastening pitch - 100 - 150 mm.

If the glass is at a distance of 800 mm or less from the bottom of the curtain and when using large format glass, protective guards must be installed.

Examples of installation of protective fences are given in the appendix.

The glass thickness, the design of protective grilles and changes in the design of doors associated with the installation of electric locks must be indicated in the working drawings.

Door dimensions

Crap. one

Notes :

1. Door schemes are shown from the side of the facade.

2. The numbers above the door schemes indicate the dimensions of the openings in decimeters.

3. Dimensions in parentheses are for doors 21-15A, 21-19, 24-15A and 24-19 with swinging leaves.

4. Doors 21-9 and 21-13A are provided for one-story buildings and waste collection facilities.

Design, shape and sizes of doors

Frame doors with swinging leaves

Sections of door details

Panel doors

1 - sealing gasket according to GOST 10174; 2 - cladding with fiberboard grades ST or T-V
thickness 3.2 - 5 mm according to GOST 4598; 3 - rail 12´ 12 mm; 4 - foam rubber gasket
2 mm thick according to GOST 7338; 5 - screw 1 - 3´ 30 according to GOST 1144, step 200 mm; 6 - mounting board

Notes :

1. The use of plastic layouts is allowed.

2. It is allowed to use mounting boards of a different design.

1 - cladding with fiberboard grades ST or T-V with a thickness of 3.2 - 4 mm in accordance with GOST 4598;
2 - sealing gasket according to GOST 10174

1 - sealing gasket according to GOST 10174; 2- fiberboard cladding grades T, T-S, T-P and T-SP group A
thickness 3.2 - 4 mm according to GOST 4598; 3 - sheathing brand 0-3 according to GOST 8242; 4 - glassine according to GOST 2697;
5 - cladding of fiberboard grades ST or ST-S with a thickness of 3.2 - 4 mm in accordance with GOST 4598; 6 - layout 19´ 13 mm

Type H

1 - sealing gasket according to GOST 10174; 2 - connection on glues of the increased water resistance;
3 - screw 1-3´ 40 according to GOST 1144, step 200 mm; 4 - foam rubber gasket 2 mm thick
GOST 7338; 5 - rail 12´ 20 mm; 6 - mounting board

1 - sealing gasket according to GOST 10174

Frame doors with swinging leaves

1 - spring loop according to GOST 5088;
2 - paper laminate according to GOST 9590; 3 - mounting board

2.11. The door purchase order must specify:

The number of doors by brand and the designation of this standard;

Type and color of finish;

glass thickness;

Instrument specification.

Type C

Doors

fire-retardant

1 - foam rubber gasket according to GOST 7338; 2 - sheet steel galvanized 0.5 mm thick; 3- cladding with fiberboard grade ST or T-V 4 mm thick in accordance with GOST 4598; 4- asbestos cardboard according to GOST 2850; 5-soft fiberboard grade M-1 12 mm thick according to GOST 4598; 6- wooden lath 12´ 30 mm; 7- screws 1-4 ´ 40 according to GOST 1144, step 200 mm

Type L

1 - sheet steel galvanized 0.5 mm thick; 2 - handle-bracket PC according to GOST 5087;
3 - boards; 4 - mineral wool boards on a synthetic binder in accordance with GOST 9573;
5 - foam rubber gasket 6´ 20 mm according to GOST 7338; 6 - loop PN1-130 according to GOST 5088;
7 - wooden stop 50 mm thick

Notes :

1. Closers are not installed in type C doors.

2. Locks are installed in the cases provided for by the working drawings.

3. Pull handles can be installed vertically or horizontally.

4. Loops for counterweight are installed in single-floor hatches. The use of loops of a different design is allowed.

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the State Committee for Civil Engineering and Architecture under the Gosstroy of the USSR

2. APPROVED AND INTRODUCED BY Decree of the State Committee of the USSR for Construction Affairs No. 51 dated April 31, 1981

3. INTRODUCED FOR THE FIRST TIME

4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS

Designation of NTD,
to which the link is given

item number,
applications

Designation of NTD,
to which the link is given

item number,
applications

I like

STATE STANDARD OF THE UNION OF THE SSR

EXTERIOR WOODEN DOORS FOR RESIDENTIAL AND PUBLIC BUILDINGS

TYPES, DESIGN AND DIMENSIONS

Wooden external doors for dwellings and public buildings. Types, structure and dimensions

GOST 24698-81

Group Zh32

OKP 53 6110; OKP 53 6196

Developed by the State Committee for Civil Engineering and Architecture under the Gosstroy of the USSR.

Performers: Yu.A. Argo (theme leader), Ph.D. tech. sciences; I.V. Strokov; I.S. Poselskaya; G.G. Kovalenko; PER. Burkova; G.V. Levushkin.

Introduced by the State Committee for Civil Engineering and Architecture under the Gosstroy of the USSR;
Deputy Chairman S.G. Zmeul.

This standard applies to wooden external hinged doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises in various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: stations, theaters, museums, sports palaces, exhibition pavilions, palaces of culture.

TYPES, SIZES AND BRANDS

1.1. Doors manufactured according to this standard, depending on the purpose, are divided into the following types:
H - entrance and vestibule;
C - service;
L - hatches and manholes.

Doors of H and C types are produced with single-leaf and double-leaf, glazed and blind leaves, with and without a threshold.

1.3. All doors manufactured in accordance with this standard are classified as doors of increased moisture resistance.

1.4. The overall dimensions of the doors must correspond to those indicated in Fig. 1. The dimensions in the drawings of the standard are given for unpainted products and parts in mm. The dimensions of the openings are given in the reference Appendix 1.

DOOR OVERALL DIMENSIONS

By agreement between the consumer and the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as using blind sheets.

Door leaves of type C, upholstered on both sides with thin-sheet galvanized steel according to GOST 7118-78, have dimensions of 6 mm in width and 5 mm less in height than those of leaves without upholstery.

Doors of type C can also be doors with solid filling and a reinforced frame in accordance with GOST 6629-74.

1.5. The following structure of the symbol (brand) of doors is established.

Examples of symbols:
entrance door or tambour single-leaf door for an opening 21 dm high and 9 dm wide, glazed, with a right hinged panel sheet, with a threshold, with type 2 cladding:
DN 21-9PShchR2 GOST 24698-81

the same, with the left hinge of the frame canvas:
DN 21-9LP GOST 24698-81

entrance door or tambour door with swinging canvases for an opening 24 dm high and 15 dm wide:
DN 24-15K GOST 24698-81

service door, two-leaf, blind, for an opening 21 dm high and 13 dm wide, insulated:

single-floor hatch for an opening with a height of 13 and a width of 10 dm:
DL 13-10 GOST 24698-81

DESIGN REQUIREMENTS

2.1. Doors must be manufactured in accordance with the requirements of GOST 475-78, this standard and according to working drawings approved in the prescribed manner.

2.2. The design, shape and dimensions of the doors must correspond to those indicated in Fig. 2 - 5, and the dimensions of the sections - to hell. 6 - 13.

DESIGN, SHAPE AND DIMENSIONS OF DOORS

Drawing 2

Sections of parts, see Fig. 6 - 8.

Drawing 3

Sections of parts, see Fig. 9

Drawing 4

Sections of parts, see Fig. 10.

Drawing 5

Sections of parts, see Fig. 11 - 13.

Drawing 6

Drawing 7

Drawing 8

Drawing 9

Drawing 10

Drawing 11

Drawing 12

Drawing 13

2.3. Sheets of panel doors should be made with solid filling of the panel with wooden slats calibrated in thickness.

Door cladding is made with materials in accordance with GOST 475-78 in the part related to doors of increased moisture resistance.

Provided that the doors are completely sheathed on the outside with profiled rails in accordance with GOST 8242-75 on a layer of glassine in accordance with GOST 2697-75 or sheathing with galvanized steel in accordance with GOST 7118-78, it is allowed to use solid wood-fiber boards of the T-400 brand in accordance with GOST 4598-74 or glued plywood brand FK in accordance with GOST 3916-69. Tambour doors are allowed to be made without sheathing with wooden slats. The rails are fastened with screws according to GOST 1144-80 or nails according to GOST 4028-63 40 mm long with anti-corrosion coating. The maximum fastening pitch is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

2.4. The lower parts of the H-type door leaves must be protected with wooden planks 16 - 19 mm thick or strips of decorative paper-laminated plastic 1.3 - 2.5 mm thick according to GOST 9590-76, superhard fiberboards 3.2 - 4 mm thick mm according to GOST 4598-74, thin-sheet galvanized steel. Wood and plastic protective materials are fixed with waterproof glue and screws with anti-corrosion coating, and steel strips - with screws 30-40 mm long according to GOST 1144-80. Mounting pitch around the perimeter 100 mm. The dimensions of the protective strips and strips are indicated in Fig. 6 - 11.

2.5. Cloths and frames of fire-retardant and insulated doors of type C should be protected with thin-sheet galvanized steel 0.35 - 0.8 mm thick according to GOST 7118-78 over the entire surface on both sides, as indicated in Fig. 12. Sheets of steel are interconnected in a single fold.
2.6. Cloths of fireproof doors of type C are covered on both sides with layers of asbestos cardboard 5 mm thick in accordance with GOST 2850-75.

Cloths of insulated doors of type C are covered on one side with a layer of soft fiber boards 12 mm thick in accordance with GOST 4598-74. Wooden laths 12 x 30 mm are fastened with nails or screws along the perimeter of the canvas from the insulation side, the fastening pitch is 100 - 150 mm.

2.7. For glazing doors, window glass with a thickness of 4 - 5 mm is used according to GOST 111-78.

If the glass is at a distance of 800 mm or less from the bottom of the curtain and when using large format glass, protective guards must be installed.

Examples of installation of protective fences are given in the recommended Annex 2.

The glass thickness, the design of protective grilles and changes in the design of doors associated with the installation of electric locks must be indicated in the working drawings.

2.8. To protect against mechanical damage to reduce noise and heat loss, type H doors must be equipped with ZD1 type door closes in accordance with GOST 5091-78, sealing gaskets in accordance with GOST 10174-72 or made of porous rubber in accordance with GOST 7338-77, door stops of the UD1 type in accordance with GOST 5091- 78. In double-leaf doors, latches ZT or latches ShV should be installed in accordance with GOST 5090-79.

2.9. The need to equip doors with locks according to GOST 5089-80 must be specified in the order.

2.10. The location of devices and their types are given in the mandatory Appendix 3.

2.11. The door purchase order must specify:
the number of doors by brand and the designation of this standard;
type and color of finish;
glass thickness;
instrument specification.

Doors wooden external for inhabited and. Wooden exterior doors for residential and public buildings

1. TYPES, SIZES AND GRADES

Damn.1. Door dimensions

2. DESIGN REQUIREMENTS

Devil 2-5. Design, shape and sizes of doors

Devil 6-13. Sections of door details

APPENDIX 1 (informative). DIMENSIONS OF DOOR OPENINGS IN THE WALLS

1. TYPES, SIZES AND GRADES

TYPES, SIZES AND BRANDS

DESIGN REQUIREMENTS

Annex 1 Reference