Crafts for giving from snags. Crafts from wood - which tree is used, interesting products from solid wood, roots and branches

Often, to decorate our home, and regardless of whether it is an apartment or a country house, we use natural materials. Their main advantage is considered to be ecological cleanliness. Again, such materials look very original and beautiful in interior design. Well, the fact that no financial costs are required for their acquisition is clearly a huge plus.

In this article, we will share some ideas DIY homemade products for home and summer cottages from branches and snags. Another option for natural materials is natural stone. Read about what can be made from pebbles in this article.

You can make a lot of useful and interesting homemade products from branches, sticks and snags. Made of them looks very original DIY furniture... And you can fantasize and experiment. For example, you can peel everything from the bark to a white state of the material, or leave it straight with the bark. In both cases, it looks very nice. But if you still decide to remove the bark, we recommend covering it with special means after assembling the entire structure. For example, acrylic or oil varnish. Well, in general, what to cover - there are a huge mass of options. Moreover, these funds can be both colorless and all kinds of shades. As for the connection of parts, they can be fastened both with fasteners (nails, self-tapping screws, screws), and using the groove-tenon technology. Again, you can make this kind of furniture for both the home and the street.

Fig. 1 DIY furniture

Fig. 2 DIY furniture

Fig. 3 DIY furniture

Fig. 4 DIY furniture

Fig. 5 DIY furniture

Fig. 6 DIY furniture

All kinds of lamps will be a very good option for products made from natural materials. They can be made from driftwood, twigs or just logs.

Fig. 7 Luminaire made of wood

Fig. 8 Luminaire made of driftwood

Fig. 9 Driftwood lamp

All kinds of shelves, coasters and tables made of branches and driftwood, which do it yourself not difficult at all.

Fig. 10 Shelf of branches and snags

Fig. 11 Shelf of branches and snags

Fig. 12 Shelf of branches and snags

Fig. 13 Shelf of branches and snags

Fig. 14 Shelf of branches and snags

Often, various cornices or hangers are made from sticks or thin logs. Well, if your house is more than one floor, then an interesting option would be a railing for a staircase made of wood.

Fig. 15 Railing from a log

Fig. 16 Hanger

Fig. 17 Hanger

Fig. 18 Hanger

Fig. 19 Driftwood cornice

Fig. 20 Driftwood hanger

Various fences made of such materials also look great. Moreover, here you can also not clean the bark. Such a fence looks very unusual.

Fig. 21 Fencing

Branches and driftwood can be hung on the wall as a decoration. The walls, decorated with sticks and logs, look very beautiful.

Well, if you replace the legs of the bed with real tree cuts, you will plunge into the atmosphere of the forest right in your bedroom.

Fig. 22 Decorating a room with a tree

Fig. 23 Decorating a room with a tree

Fig. 24 Decorating a room with a tree

Fig. 25 Decorating a room with a tree

Furniture from roots is interesting in that it is definitely not possible to create 2 identical copies. It will look good in a country house, where at least a piece of nature should be present, or on the street. Leaving the city for fresh air, you want everything to be beautiful, fabulous ... All the materials from which the furniture was made should have been natural. Furniture? made from ordinary tree roots? would be the perfect option!

Advantages of the presented type of furniture

Products for the site must be durable, moisture resistant. The tree does an excellent job with the tasks. Furniture can be bought or made by yourself. The tree has been used since time immemorial, and now it has not lost its relevance. Previously, they tried to decorate, improve, in various ways, roots were often used. Now this option also has the right to exist.

The use of roots began in the late 18th century. People were fascinated by bizarre shapes. Each item became individual. Furniture of this kind was in the collections of kings.

Then they forgot about the original method of furniture production, but after a while they revived it again, and it became popular again.

Main distinguishing features:

1. Since each tree is unique, products made from it will also be unique. You will not find the second such in the world.
2. The furniture is environmentally friendly, absolutely safe.
3. The roots are strong, which means that the products are as reliable as possible.
4. Any kind of furniture can be made.

Who is the original solution for

The roots have an expressive shape, suitable for fans of non-standard solutions. Much depends on the conditions in which the tree grew. The more difficult the conditions were, the more bizarre the roots will turn out. If the master is experienced, it will not be difficult for him to find interesting solutions.

Wood products are very durable, furniture is made "for centuries". This applies to those tables, chairs, which are made from a single piece of wood. A whole tree stump with roots is often used.

What can be done

The roots of trees are traditionally used for the production of tables, chairs, and decoration. The products turn out to be fabulously beautiful, quite homemade.

Among the modern interior, original things will look conceptually. Wooden furniture is perfect for a summer residence, a country house. Coniferous products are good for sauna use.

One interesting idea is using roots to create a folk style bar. So each visitor will have a favorite hanger, table, chair. The style can be sustained in any subject. Wood allows you to make any kind of furniture - from flower stands to shelves.

With the help of roots, you can decorate the following things:

• dressers;
• cabinets;
• tables and chairs;
• bed.

On the walls, you can make a panel that imitates living trees.

How to properly prepare the roots

Finding tree roots in our country will not be difficult. It is enough to go to the forest and choose the most interesting driftwood. The question is - how to properly prepare them?

First, you should decide on the material for the frame, backs, legs. The following tree varieties are good options:

• conifers;
• Apple tree;
• nut;
• Birch.

The roots must be thick enough. It is important to make a layout in advance in order to clearly understand what should turn out.

Which roots to take, dry or fresh? Any option can be used. If you see cracks in the wood, that's good, the marks will give a lot of personality, as long as the strength does not decrease. You need to dry so that the tree does not lead. It is better if the process takes place in stages, under a canopy. Drying takes place in an unheated room.

Next comes the processing of the roots. A brush is used for rough roughing, preliminarily clamped in a drill. It is necessary to follow safety rules, wear goggles, respirator. After getting rid of the main dirt, a fine brush is taken, processing continues.

Build rules

The processing of the ends assumes observance of the nuances. Processing is carried out with a coarse brush. Cleaning is done using a drill. You need to act clockwise. You should not press! Then processing is carried out with a fine brush. Next, the roots are dried, assembly is in progress.

Methods of joining pieces of furniture can be different - gluing, wedge-shaped, mounting on screws. When choosing a fastening on a wood grouse screw, you can put a decorative plug on top. The joints are treated with special glue.

Sitting can be done from multiple roots. You can fasten them with a hemp rope. The method will make the furniture durable and individual.

Finishing

If cracks are found that are not credible, they can be repaired with dark colored epoxy. Then the product is sanded.

After grinding and assembly, the excess glue is removed, and the decoration begins. A stain is taken, the product is covered in several layers until the desired color is obtained. In a number of places, accents are placed. Then oil is applied. Then you can enjoy your creativity!

Anyone can make tables, chairs or shelves from tree roots. The material is found in large quantities in the nearby forest. First of all, you need to correctly choose the type of tree. The roots are allowed to be taken both fresh and dried. Original furniture from the roots will be an ideal option for a personal plot, bar, sauna, modern apartment. You will get an exclusive piece of furniture. Do not be afraid to take roots with cracks, they give a special charm.

Furniture from roots (video)

https://dachadecor.ru/images/kdjkldsjflkdsDD_201.jpg "alt =" (! LANG: Furniture from roots: fabulous beauty" width="345" height="227" border="0">!}

It is impossible to list all the ideas arising from the masters during the manufacture of various crafts from snags. We will focus only on a few rather simple but effective decorative items. None of them should be done by men, while others can be handled without problems by women.

What do you need for crafts? Just two things.

1. A wish. Making various items with your own hands does not attract everyone; some of our compatriots prefer to buy beautiful things in stores. The article is intended for those who get real moral pleasure from things made with their own hands and do not want to have consumer goods in their home.
2. Free time. It is required not only for the creative process itself, but also for the preparation of snags - one must independently visit the forest in search of suitable material. True connoisseurs of home art from every outdoor recreation bring home various branches and driftwood. Even if during the collection of blanks there is still no clear idea of ​​their future fate, then each branch and each snag will find its purpose.

Process steps

Each business must be organized and planned in advance, in this way it will be possible to avoid many annoying mistakes.

The more blanks you have, the easier it is to work later. The fact is that creative ideas also come during production, and for their implementation you need to have material.

Howrightcook driftwood

Small snags are used for crafts, their preparation can be done at home. The process consists of several stages. First of all, the surface must be cleaned of dirt, use any brushes. To facilitate the process, it is recommended to wet the dried soil first. Further, special processing is performed.

1. Prepare a container according to the dimensions of the driftwood, it can be a plastic bowl or a barrel, it does not matter, The main condition is that the driftwood must completely get in it. If you soak it in separate areas, then there is a high probability that stripes will remain on the tree, indicating the boundaries of the water. This has a very negative effect on the appearance of the product; it is difficult to get rid of the marks.
2. Add 100 grams of baking soda per liter of water to the water.
3. Dip a snag into the water and press it down strongly with a load, it should not float, but completely immerse itself in the solution. Hold in this position for at least a day.
4. The surface of the wood has cleared but darkened - this is the effect of baking soda. If your craft requires a white surface, then pour bleach into clean water at a rate of 1:15 and again drown the snag in the liquid, soak for at least two days. Check the condition periodically, you can increase the concentration of bleach or the holding time.

Now you need to get the snag and dry it well. What to do with it further depends on the type and manufacturing technology of the selected craft.

Prices for wood preservatives

Impregnation for wood

MostsuccessfuldizaynerskieDIY solutions

Name of crafts	Description and tips for making
	Not a single person can repeat the natural pretentiousness of the driftwood bends, its forms best of all reflect the freedom of natural development. It is necessary to pick up a snag with long roots, if there are none, do not be discouraged. You can bend them in the desired position later in hot water. It is very important to come up with a stand, it must guarantee the stability of the structure and prevent overturning. The wood can be of a natural color without various surface finishes. The electric cable must be hidden, it will not be possible to do this with the help of branches, it is recommended to use a thick natural linen rope for this purpose. There are options for using individual parts of a table lamp or sconce and attaching them to snags in an original way. During manufacturing, unquestioningly comply with the requirements of the PUE, do not forget that wood is a combustible material and requires special measures to protect against fire.
	A simpler craft, for manufacturing you can use both large driftwood and individual branches. There are a lot of design options, the same do not exist. Each twist of the driftwood can be used to give it a special look and accentuate its geometry.
	Any photographs decorate the interior, and if they are also in exclusive frames, then the effect increases many times over. Frames can be geometrically correct or bizarre natural shapes, different sizes. Hang on the wall or mounted on bedside tables, have a natural color or be covered in bright, catchy colors. The specific type does not really matter, there are a huge number of solutions. The option that you personally like is considered ideal; this is the main criterion for choosing a frame design.
	It can be used both in summer cottages and in city apartments, looks great in saunas. On the one hand, you need to thin out the roots a little and make room for clothes. Special shelves or hangers are made for hats.
	In recent years, fascination with Japanese folk traditions has become very fashionable in our country. An excellent bonsai can be made from driftwood, the technology is simple, the entire composition can be ready in just one day.

Candlesticks and vases

Lamps and fixtures

Decorations

Snag shelves

Step by stepwaya inwithbonsai making instructions

Step 1. Find a small snag that looks like an old tree. It should have a prominent thick trunk and branches of the crown on the sides. Do not pay attention to small branches, they can be cut off later.

Step 2. Clean it from dirt, wash and dry. First, cut off all unnecessary with a pruner and form a crown, work carefully, nothing can be glued back.

Practical advice. It is much easier and quicker to clean the driftwood with an old toothbrush. Its villi get dirt from even the smallest pits and curves.

Step 3. Stir the alabaster. The amount depends on the container in which you plan to fix the snag. Alabaster will hold it and imitate the earth.

The larger the driftwood, the larger and heavier the base must be in order to guarantee the stability of the structure. In our case, about 0.7–0.9 liters of the finished mass is enough.

Remember that alabaster hardens very quickly, prepare the container for the composition first, then there will be no time to look.

Step 4. Hold the snag upright with one hand and level the alabaster with the other. If dirty spots of the mass appear on the surface of the driftwood, then they must be thoroughly removed immediately with a slightly damp cloth. After drying, white alabaster is deeply absorbed into the wood, it is almost impossible to clean the surface.

Wait a little until the solution begins to seize, the driftwood should hold on by itself. Leave the solution alone to set completely, this will take about 10-20 minutes.

Step 5. Prepare special artificial branches of pine or spruce, they are then cut into small branches and inserted into the snag. To make holes, you must have an awl or hand drill. The surface of the wood is impregnated with wood stain, it emphasizes the structure. Prepare small stones and a glue gun. It is better to use a modern hot one, it is easy to work with it, and the adhesion rates are quite sufficient for our craft. To improve the design look, a finishing varnish is made. All of these materials must be prepared in advance.

Step 6. Use a small brush to paint the alabaster stain. The material absorbs a lot of water, it will be necessary to cover one place at least three to four times.

Step 7. Saturate the driftwood with stain, here you need to be careful and achieve the most natural color of the tree. Do not make it completely the same tonality, let there be areas with different shades.

Step 8. Use a small hand drill to carefully make holes in the driftwood, fill them with hot glue and immediately insert the pieces of artificial needles. Work carefully, do not leave thin strands of glue. They can be removed immediately or after the composition has set. The second option is preferable, the threads are easily torn off at the base, the hands are not scalded.

Step 9. Gradually shape the crown of the tree. Do your best to keep everything looking organic.

Glue gun prices

Glue gun

Step 10. Cover the alabaster with moss, attach some of it to the driftwood. The fact is that in Japan such trees have been growing for many decades, and the trunk is necessarily covered with live moss.

This completes the manufacture of the craft, you can install it in the allotted place and enjoy the results of your labors.

Artificial bonsai from driftwood

Step by stepinstructionfor makinghangers

This craft can be hung in a bathhouse or a hunting lodge, in an apartment it will look very exotic and not everyone likes it. This craft is not for everybody, there are never extra hangers. For manufacturing, you need a rather long driftwood with a small number of roots. Additionally, you need to prepare several twisted branches. The material is needed without bark, it must first be cleaned of dirt and washed thoroughly. There is no specific hanger project yet, decisions will be made as the craft is made.

Step 1. Using long self-tapping screws, screw a branch with small branches to the snag, they will serve as hooks. Choose the most stable position, the horizontal branch should have at least the spirit of rigid stops at the maximum distance from each other. Due to this, the overturning shoulder is reduced, the hanger is more reliable and stable.

Step 2. In small-diameter branches, drill holes for self-tapping screws, otherwise the tree will crack. Driftwood does not have an even structure of wood, the roots always have ornateness, the fibers are twisted, there are other natural malformations. Such a tree cannot hold internal stresses, all measures must be taken to prevent their formation.

Step 3. Prepare a small piece of board, sand it first and cover it with several coats of varnish. A horizontal shelf will be made from this board. Place the hanger on the table in approximately the same position that it will occupy on the wall. Think about how best to fix the shelf. Try several options, don't screw anything yet.

Cordless Drill Prices

Cordless drill

You need to achieve such a position that two conditions are fulfilled simultaneously.

1. The shelf must be securely fastened. Determine at least three branches for the stop, their diameter should allow the existing screws to be screwed in.
2. Things are stored on the shelf, and for this it must be in a horizontal position. See how to fix it correctly. If there are problems, then change the angle of inclination of the entire hanger so that the shelf takes the correct position.

Practical advice. The craft looks the better, the fewer any connections are noticeable. Never chip or saw anything, screw the screws in inconspicuous places.

If it is not possible to naturally hide some of the joints, then sink them into the wood, and seal the holes with a special putty. But this is an extreme option, experienced craftsmen will always see the place where the putty is applied.

Step 4. Carefully inspect the craft, check the strength of the structure. If hesitation is found, then additionally fix the connections. You can use branches not only to increase strength, but also as additional elements for placing clothes.

Video - Driftwood hanger

Large snags can be used to make garden benches, tables and chairs, etc. With minimal wood carving skills, strange fairy-tale animals, forest dwellers and wizards are made. The main advantage of such crafts is that there are no two identical products in the world.

Snag tables

Crafts made from snags can become a real highlight of the interior, trees that have outlived their life get a second chance and delight people for a long period of time. Crafts from snags look great against the background of modern furniture styles, but it is even better to design a special recreation area from them. Try to make an original composition with your own hands and place next to crafts from snags handicrafts from branches.

25.09.2018 354 Views

Creative coasters for home decor

Autumn is an interesting time of the year. At first, the crowns of trees take on yellow and red color, and then the leaves fall off, causing dejection. It is during this period that you need to diversify your life with something interesting and original. It's about crafts made from snags. It turns out that at first glance, unnecessary twigs can be very useful to you in the interior or in your summer cottage. Consider 5 master classes related to making beauty with your own hands.

• Using driftwood for furniture
• Lighting
• Original panels from snags
• Picture frame



Stylish DIY interior item












How to prepare branches for crafts?

From an ordinary, unremarkable driftwood, you can make original wood, which will later be used for homemade gizmos. Many craftswomen are wondering about the intricacies of preparing this material. The process is simple if you follow a certain order of actions. For preparatory activities, you will need the following items (they are found in almost every home):

• Plastic container.
• Soda ash.
• Sandpaper.
• Linen bleach.



Soaking an old branch in a solution

Preparing branches

• Take a plastic container and add about half a glass of baking soda to it, and then pour hot water over the contents.
• Now you need to send branches into this container and press them down hard - until the wood is completely covered with water. Then you need to put a heavy load on the tree, which will act as an anchor to hold it under the moisture. Leave for two days.
• After the process of peeling the branches, you will notice that the wood is uneven in color. Now we have to deal with her whitening. You need to pour bleach into clean water and fill it with water at a ratio of 1:15. The wood is again immersed 100% in the container and left for 48 hours.
• Subsequently, the snags are taken out and put on a sunny place for several more days. After three days, you will receive products ready for creativity. But while they are very rough, so sharp places are subject to cleaning and grinding.



Original photo frame idea

Using branches for furniture

Large driftwood is ideal for creating tables and clothes hangers. Medium-sized raw materials will be the best option for the manufacture of shelves, children's furniture. And small driftwood will come in handy for individual details. When making furniture structures, it is important to consider some points.












• Driftwood must necessarily be strong, since they have to take on an enormous load, especially when it comes to pieces of furniture of impressive size.
• The raw materials are prepared for work in accordance with the information indicated above. They need to be bleached and sanded.
• Next, the tools are being prepared. You will need a drill, screwdriver, nails for knocking down snags, if this is provided by the furniture structure. Other equipment is also being prepared, which is necessary to create an original craft.
• After the production process, the driftwood should be once again treated with compounds that prevent rotting and pests. Leave it for a couple of days, and then put the piece of furniture into operation.



Interesting pieces with unusual shapes will become an irreplaceable functional piece of furniture

Since there are a lot of furniture structures made of driftwood, it is worth using the tips for making specific types of furniture.

Lighting

From driftwood, it turns out, you can make a gorgeous lamp! Of course, there are many design options, but we will consider the process and algorithm using the example of a classic product. Whatever we say about its standard, it will look unusual, but its appearance will allow it to fit into absolutely any interior.



Luminaire made of wood and rope

Now - about the manufacturing procedure. Arm yourself with certain materials and get started.

• Take one large snag (up to 1 m long). It is desirable that it have an interesting shape (curly branches in the original order). Choose the breed at your discretion, but it is best to give preference to oak or pine needles: the production process will give you a lot of pleasant emotions, and the result will amaze you with its unusualness.
• Process the wood according to the first master class, and then along the entire length of the base and individual branches at a distance of 10 cm from each other, make holes in it in order to insert decorations into them. These can be metal accessories, decorative stones, ribbon bows.
  
  

  The uniqueness of the luminaire depends on the shape of the tree that acts as the basis

  

  An illustrative example of converting a decorative lamp

• Prepare the base for the lamp. It can be a purchased part in the form of a regular stand. Then you need to connect the stand and the snag in a convenient way. To do this, you will have to acquire carpentry skills, it will be difficult for a beginner. The thickest part of the driftwood should be closer to the pallet, and the thinnest part will act as the top.
• A decorative braid or rope 20-30 cm long is suspended from the upper part of the structure.On the other side of this thick thread, an electric mechanism will be located, that is, a system for turning on and off the lamp.
• To prevent the bulb from being "naked", provide a lampshade for it. This step is a matter of your imagination. You can make it yourself or buy a ready-made version.



Rotten wood can be turned into a spectacular decorative element

Original panels from snags

If you want to get involved in the process of such needlework, stylish and interesting panels will help you. They are hung on the wall and used as paintings or candle holders, souvenirs. In our case, a master class on making a panel candlestick will be considered.



Great material for creating original items

• Prepare a rectangular driftwood (it can be a felling of a log) 30 cm long and 10 cm wide. Process it in accordance with the first master class. This will be the basis of the panel.
• Another element is attached across the base. It should have the shape of a parallelepiped and match the length of the base. Fastening can be done with nails or good wood glue.
• Then you just have to process the tree and put a candle on the protruding element - your home will be transformed in the blink of an eye!



Candlestick made of solid dry wood

This is how this original panel looks like. If you follow the instructions given, the result will pleasantly surprise you.

Photo frame made of driftwood

Do you want to make your interior unique and capture the best moments of your life forever? Why not make a photo frame from driftwood? All you need is a couple of small twigs and good glue. The branches need to be carefully prepared in accordance with the first master class, and then proceed to the main part of the work.



Easy and effortless activity to decorate your own home

• First, the canvas itself is made. This is a block of wood 2 cm thick. The length and width are determined by the dimensions of the photo (9 * 13, 10 * 15 cm and so on). Please note that these indicators should be with a margin of 2-3 cm, so in fact you will need a beam of 12 * 16 cm or 13 * 18 cm, respectively.
• The canvas is processed with sandpaper, covered with anti-rot and deterioration compounds. Then a photo is placed on it face up, and small twigs are superimposed on the perimeter in an indent of 2-3 cm and fixed with glue.
• If you want to diversify your picture, you can put not just twigs, but driftwood, painted in different colors. The order of laying out is determined by the author.













As a result, you will get an original stylish photo frame, which will become a wonderful gift for family and friends.

Ordinary tree twigs, which are usually abundant in an orchard or a backyard, are a unique material.

Nature has already given them bizarre forms that, with proper imagination and a little skill, can be turned into a real work of art. Crafts from tree branches will fit into the home environment in an original way, help to diversify and decorate the interior.

Material requirements

Of course, not every branch is suitable for making crafts. It is better to harvest the material in early spring or autumn, when the bark and core are not touched by bark beetles.

There are no requirements for the type of wood: birch, willow, grape and other branches are equally suitable for making crafts. The main thing is that the material does not have traces of the presence of pests, chips and other defects.

To exclude the appearance of any insect larvae in the house, the collected branches are recommended to be treated with a weakly concentrated solution of potassium permanganate.

So that the craft from branches and snags for the interior does not warp, the material must be preliminary. This can be done in two ways:

• in vivo by spreading the branches in an even layer on the floor and keeping at room temperature for about 2 weeks;
• expedited process- spread out on a baking sheet and place in the oven for 3 hours. There must be a slow fire and a slightly open door so that the moisture comes out evenly.

If it is supposed to remove bark from wood for crafts, this operation must be performed before drying begins. When the branches have been freed from excess moisture, the surface can be covered with wood varnish.

Decorative candlestick

This is the easiest way to make crafts with your own hands. It will take less than an hour to make a decorative piece. For work you will need:

• glass beaker. A container with high and low walls is suitable, it is better to choose transparent glass, but this moment remains at the discretion of the master;
• glue;
• thin dry branches;
• small secateurs.

At the initial stage, the lower parts of the branches need to be trimmed so that they lie flat against the bottom of the glass. The proportionality of the upper part does not play a significant role.

The further operation is simple: we spread the branches with glue and glue them to the glass wall close to each other. The candle is inserted inside the glass container, and the original candlestick for decorating a room or a romantic dinner is ready.

The second version of this craft: the branches are glued directly to the candle. For this, thin willow twigs, which have a straight shape, are more suitable. However, such products are used only as a decoration: it is not worth lighting a candle covered with dry wood for reasons of fire safety.

Photo frames and mirrors

From tree branches, you can make a beautiful frame for a family photo or a mirror in the hallway. The work is carried out according to an identical scheme, the difference lies only in the method of registration and the amount of consumables for crafts.

To decorate the photo, dried and varnished thin twigs are glued to a wooden frame.

Note! You can also make the base of the photo frame yourself by cutting out a rectangle with a jigsaw from plywood.

The pasting starts from the long sides. The twigs are laid close to each other, two or three rows are allowed. Then the short sides of the frame are pasted over in a similar pattern. At the corners, the ends of the branches can be laid end-to-end or with an intersection, both options look equally interesting. As an additional decoration for the craft, you can use dried moss or any other decoration at the discretion of the master.

In a similar way, you can make an original frame for the mirror. However, the base has a larger area here, and finding relatively straight branches can be problematic. In such cases, the starting material can be cut into small pieces (3-5 cm) and the branches can be glued not parallel, but perpendicular to the base. There will be more time to make such a craft from branches, but an ordinary mirror will look elegant and unusual.

Stands

Having cut down an old tree in the country, you do not need to immediately send it to the fire. A small part of the barrel can be used to make an original stationery stand. To create this craft you will need:

• saw cut of a trunk with a diameter of not more than 15 cm, a height of 5-8 cm;
• drill with a set of drills;
• fine-grained sandpaper;
• varnish for wood processing.

The workpiece is cleared of bark if necessary, the lower part, which will serve as the base, is leveled to give stability. Holes are drilled in the upper part, the distance between each is maintained at 5-10 mm. Then all surfaces and corners are sanded with sandpaper. At the final stage, the wood is covered with several layers of varnish, and after drying, the holder for pencils and pens is ready for use.

Hanger

Homemade hangers are ideal for decorating the hallways of apartment buildings and private houses, summer cottages. This is not even a craft, but a real carpentry made from tree branches.

For manufacturing you will need:

• board. Its length and width are chosen arbitrarily, depending on the amount of clothes that will be placed on the hanger;
• thick branches of trees with branches of branches, preferably located at an acute angle.
• self-tapping screws;
• saw;
• paints and varnishes.

The base board must be sawn in accordance with the specified dimensions, varnished or painted, having previously treated the surface with sandpaper.

Each thick branch is cut to a length of 30-40 cm, 1-2 branches are left on the base, which will function as clothes hooks. The back of the knots can be chipped off to ensure a snug fit to the base.

The branches-hooks are fastened with self-tapping screws, if a homemade hanger is not supposed to be used for storing heavy things, you can do with glue.

Vases

Flower pots and flower vases can also be beautifully decorated with branches. To do this, the branches are cut on both sides so that the source material has the same dimensions. The branches are laid out in one row on the table, tied together with a strong thick thread, twine. To make the design more presentable and durable, the branches are fixed in two places: above and below. If the work is done correctly, you should get a path of tight-fitting twigs.

A vase or flower pot is pasted over with burlap. At the final stage, the branches are wrapped around the base, the ends of the twine are tied together with a bow. As an additional decoration, the surface of the wooden craft can be varnished or decorated with decorative elements.

As a decoration for branches for a vase, they make flowers out of paper with their own hands, then stick them on the craft. They use cones, old beads, pieces of cotton wool. Diode bulbs look beautiful as a backlight for a floor vase.

Crafts from roots and snags

Remarkably, a stylish decorative piece or handmade wooden sculpture can be created with a minimum of effort. Stumps, driftwood, roots, which remain in large quantities after harvesting trees, will help with this. In fact, the driftwood is already a finished sculpture, which only needs to be peeled from the bark, dried and varnished. Children are happy to search for interesting forms. Crafts made from snags are suitable for older groups in the kindergarten and for school.

In general, wood is a unique raw material for construction or home art. This is an environmentally friendly material that is easy to process, retains its original properties for a long time, does not require special care.

In addition, even ordinary branches and twigs that go to kindle a fire can turn into real works of art even in the hands of an inexperienced master. Crafts are made from small branches and large branches, first sawing off all unnecessary.

From the scraps of tree trunks, you can fold a low woodpile, decorating it with thin branches on top - you get an interesting coffee table that will organically fit into any interior.

Branches with a diameter of 5-7 cm and a height of 1.5 m are collected in a rectangular frame. The walls are created from branches folded in a criss-cross pattern. We put glass on top and get a beautiful dressing table.

You can decorate the interior with tree branches and decorate almost any piece of home furniture: floor lamps, shelves, ceiling chandeliers and wall lamps. Finally, thin twigs can simply be placed in a vase, making a decorative composition.