The pressure created by the baby pump. Benefits of submersible pumps kid

Many owners of summer cottages and private households that are not connected to a centralized water supply are familiar with the problem of supplying water to their homes and gardens.

The “Kid” submersible pump will help to partially solve it, which, although not a powerful device capable of pumping water from artesian wells, will quite cope with the supply of water from wells, shallow wells and open reservoirs.

It will be useful for those who are just going to equip an autonomous water supply, as well as users of pumping equipment, to learn about the device, the principle of operation and the rules for operating the unit. We will describe in detail how to install the "Baby" in the well and ensure its smooth operation.

Submersible pumps of the “Malysh” series are produced by the Russian enterprise Livgidromash, whose history goes back nearly seventy years. During this time, more than three million copies of various pumping equipment have rolled off the assembly line of the plant.

The use of a filter will not only extend the life of the unit, but also ensure the supply of better quality water, purified from any impurities.

Pump Maintenance Malysh

In order for the pump to serve for a long time and properly, it is necessary to observe the operating and storage conditions recommended by the manufacturer. In this case, the manufacturer guarantees its normal operation for two years. The pump does not require complex maintenance and care, and it will not be difficult to follow simple rules.

After the first installation of the device in the well, you need to let it work for one to two hours, and then take it out and carefully inspect the body and components for faults. If everything is normal, then the vibration pump can be put in place and used further, leaving it immersed in water for a long time.

Periodically, at least once every three months, and if possible, then every hundred hours of operation, it is also necessary to inspect the unit. If at the same time traces of friction are found on the body, it means that it was installed incorrectly and, during operation, came into contact with the walls of the water intake.

To avoid this, it is necessary to set it evenly and put an additional rubber ring on the body.

If the inlet holes are clogged, they must be carefully cleaned without damaging the rubber valve. For cleaning, it is best to use a tool with a blunt end.

If the pump is not used in winter, it must be pulled out of the well, washed and dried well. During storage, the unit should be placed away from heaters and protected from direct sunlight.

If, following the manufacturer's recommendations, a breakdown occurs for reasons beyond the control of the user, the pump should be taken to a service center. A list of popular breakdowns of the “Baby” pump and ways to fix them are described in.

Submersible pump "Kid" is a convenient and inexpensive household appliance, easy to use and easy to maintain. Of course, due to its low power, it is not able to provide a full-fledged water supply to a private house, and, in fact, no one sets such tasks for it.

An inexpensive vibrator is perfect for seasonal use. He will become a real assistant in summer cottages. So, with the help of "Kid" you can organize watering plants and water supply from wells, wells or open reservoirs.

Have experience installing or using a Baby pump? Please share information with our readers, tell us about the specifics of the unit. You can leave comments and ask questions in the form below.

The most inexpensive, but reliable devices for pumping water from wells and shallow wells include a Brook or Malysh pump. They are characterized by simple design, stable operation, durability, and a pleasant ratio of price and technical capabilities.

The types and parameters of the Kid will be discussed in this article.

Application area

The operating power of the Baby pump is small, so it cannot be used to extract water from deep. But it works great in wells and wells "on the sand", and can also pump water from rivers and lakes containing mechanical impurities.

What tasks can be solved with its help:

Lifting water from a depth of up to 40 meters;
Its injection into the water supply system of the house and site;
Watering garden plantings;
Pumping water from pools, flooded basements and cellars;
Washing a car, paths and platforms, facades of buildings, etc.

Note. The device of the vibration pump Malysh allows you to use it for pumping liquids contaminated with insoluble impurities - sand, silt. But if their number exceeds the maximum allowable, a filtration system is needed.

Operating principle

Submersible pump Malysh is a vibration unit, the principle of which is based on the conversion of electrical energy into electromagnetic oscillations. They are transmitted to the piston, the vibrations of which lead to the injection of liquid and its expulsion from the device. Every second, the piston makes about a hundred reciprocating movements.

A coil with a core is responsible for converting electricity into electromagnetic. Its winding is quite sensitive to overheating, which occurs when the pump is idling. Therefore, you must always monitor the water level in the source or supply the device with an automatic switch that trips when it drops critically.

Depending on the location of the suction valve, Toddlers are divided into two types of construction:

With top intake. In it, the working elements are located in the lower part of the body, so they are always in the water and cool better, and less sand, silt and other contaminants from the bottom of the source get into the suction hole;
With bottom intake. Less resistant to overheating, require constant monitoring, and when working in a low-rate well (see) - installation of mechanical filters on the suction pipe.

Advice. Do not ignore the recommendations for installing a filter, this will save your pump parts from wear. Moreover, the price of the most popular EFVP filter for vibration pumps is only about a hundred rubles.

Specifications and features of models

In the line of pumps of this brand there are several models with top and bottom suction. All of them are used to take water from a well or a shallow well, as well as from open reservoirs, and supply it in a horizontal direction to a distance of 100-150 meters. Which makes them convenient both for water supply at home (see), and for watering a personal plot.

Note. The Baby pump for a well can only work with water, the temperature of which does not exceed 35 degrees, and the content of contaminants and insoluble impurities is not more than 0.01% of the volume.

Conventions

When studying the pump before buying, you should pay attention to the markings and be able to decipher the alphanumeric designations.

How to do this, we will tell using the example of the device BV 0.12-40 Malysh-K (p) Ikl:

BV- household vibration;
0,12 - nominal flow in liters per second;
40 - head in meters at nominal flow;
Kid-K- the name in which the letter K indicates the presence of built-in thermal protection;

Note. Malysh-3 is the only pump of all units of this brand that can be used in narrow three-inch wells.

(P)- if this letter is present in brackets in the designation, then the device case is made of high-strength plastic. Its absence indicates an aluminum case;

Ikl– the first class of protection against electric shock. The absence of such a designation indicates the second class.

Basic model Kid

This is the simplest modification with a lower water intake, designed to work in a source with a diameter of at least 100 mm. It has no filter, no overheating protection, no pressure switch. But all this can be purchased and installed separately, as well as a hose with a diameter of 18-22 mm for supplying pumped water to the consumer.

Deep well pump Kid features the following:

Note. These parameters are approximately the same for all modifications.

Malysh-M

In terms of its parameters, this unit does not differ from the base model, the difference lies in the upper location of the water intake valve. The performance of the Malysh-M pump is the same as that of the Malysh.

Kid-3

The diameter of the Malysh-3 pump allows it to be used in narrower wells - from 80 mm. This is a more compact version of the basic model, with a reduced power rating to 165 W and a head of up to 20 m. It is ideal for installation in low flow sources.

The kit includes a network waterproof cable 30 meters long.

Kid-K

This is the most advanced modification with built-in thermal protection and lower water intake. Automation protects the device from overheating, disconnecting it from the network in time when the engine temperature rises. Unlike other devices, rewinding the Malysh-K pump as a result of winding combustion is not required.

Features of installation and connection

The main rule: the pump must be mounted in a vertical position, otherwise its service life will be seriously reduced. And the depth of its immersion should be such that the suction hole is always in the water. Therefore, you need to know the lower dynamic water level in your source.

For reference. The dynamic level is the mark at which water is held in the well when the pump is running. It depends on its performance.

Installation instructions:

Prepare the water supply hose. Its length must correspond to the immersion depth, and its diameter must correspond to the diameter of the discharge pipe;
Fasten the hose to the nozzle with a plastic clamp;
Attach the filter to the suction pipe. This is especially true for pumps with a lower water intake, since mechanical impurities entering the working chamber of the device lead to rapid wear of the check valve and piston, clog the hose, which leads to a critical increase in pressure inside the device;

Advice. Bottom suction pumps should not be placed closer than 50 cm from the bottom of a well or well, even if they are equipped with a filter.

Make sure the network cable is long enough. If this is not the case, you need to build it up with your own hands, but so that the junction is above the level of the well;
Combine the hose and cable with plastic clamps so that the latter cannot slide down, but is in a loose state;

If there is a very small gap between the pump and the walls, then a rubber ring must be put on its body, which will prevent mechanical damage to the device from vibration;
Fix a steel cable or a nylon cord that comes with the pump in a special eye on the body. Tie an elastic rubber band about 50 cm long to its upper end - it will dampen the vibration;
Lower the rope pump into the source to the specified depth, then carefully secure the rope from the outside.

Now you can connect the cable to the network and use the device. Connection is possible only after complete immersion, as idling will quickly lead to breakage.

Unfortunately, the pressure that the Malysh pump creates does not suit everyone, especially if there are appliances in the house, for the normal operation of which it must be at least 2 atm. Vibrating devices are, in principle, capable of producing it, but if the source is located far away, then significant pressure losses occur in horizontal sections.

But there is a way out: the pump must be additionally equipped with a check valve, a pressure switch and a hydraulic accumulator, turning it into a mini-pumping station. Automatic maintenance of the water level in the accumulator is carried out using a relay: it turns on the pump when the pressure in it drops.

Automation for the pump

Dry running controllers that turn off the unit when air or sand enters it;
Float switches activated when the water level drops;
Pressure switch and thermal relay;
The stabilizer for the pump Kid, maintaining the current unchanged during pressure surges;
Start-up devices;
check valves;
Hydraulic accumulators that maintain pressure in the network through a pressure switch.

To get an idea of how it all works, we suggest studying the following diagram:

1 - control node;
2 - cable with a plug for connecting to the network;
3 - cable with a socket for connecting the pump;
4 - automatic switch;
5 - socket;
6 - pump Malysh;
7 - power cable;
8 - nipple;
9 - check valve;
10 - pressure pipeline;
11 - cross;
12 - adapter nipple;
13 - flexible eyeliner;
14 - hydraulic accumulator;
15 - distribution pipeline.

When the pump is turned on, it supplies water to the accumulator connected to the automation system. When the pressure in it reaches the nominal value, the pressure switch turns off the pump and turns it on again when it drops.

Advice. To drain water from the system for the winter, insert a ball valve between the filter and the check valve.

Conclusion

The technical characteristics of the vibration pumps Kid, of course, are not amazing. But these devices successfully cope with the water supply of a small country house or cottage of several acres. Which, combined with a low cost, cannot but rejoice.

In order to avoid mistakes when choosing and installing a pump, we recommend that you watch the video in this article before buying it.

To ensure water supply in summer cottages and farms, it is worth using a household electric pump. The Malysh submersible pump is considered a universal option, which is used at various facilities where water supply is required. The name of the equipment is explained by its compact size and light weight. Despite the modest power, such a device guarantees a good water pressure.

Applications

People living in rural areas, as well as summer residents, use the Malysh pump for the following purposes:

providing water to non-residential and residential facilities;
water supply for summer cottages and vegetable gardens;
the inclusion of an irrigation system operating in automatic mode, which facilitates the care of plants;
spraying shrubs and green spaces with spray nozzles;
water pumping.

It is important to remember that submersible pumps are not designed for pumping contaminated liquid, because in this case, the details of the structure will quickly wear out. Accordingly, the service life will be short.

In general, a wide range of applications for Malysh submersible pumps is explained by ease of operation, reliability and low price. Also an important role is played by the absence of the need for installation. The pump will start working immediately after immersion in water.

Many consumers prefer submersible models with top water intake, thanks to which it will be possible to avoid contamination from the bottom including sand and silt. Moreover, this equipment cools faster, which means that you can not be afraid of engine overheating and its failure. These pumps are used to lift water from a well or well. They are also an important element in an autonomous water supply system.

Main characteristics

Universal submersible pumps may have different characteristics depending on the manufacturer and specific modification.

Separately, it is worth mentioning the presence of automation. Thanks to such equipment of the Malysh submersible structures, maintenance and operation are simplified, and safety is increased. The automatic system maintains a certain pressure and monitors the operation of the engine. Also, the automation will protect the Baby pump from overheating, and the engine will not suffer due to power surges. If the water level is insufficient, the pump will be powered off.

On sale you can find models with an electric generator or equipment powered by solar panels.

Universal units are sold at an affordable price, which affects the service life. Usually, working resource is designed for 3-4 years. In this case, the device will pay for itself in one season.

For many consumers, the classic model is considered the best option. It is suitable for wells with a diameter of 100 mm and provides water supply over a distance of 100-150 m. It is important to remember that in the basic version there is no automation that protects the unit from overheating, and this reduces the price of equipment and reduces the service life.

Principle of operation

After connecting the drive to the network, the electricity is converted into electromagnetic oscillations. They enter the corresponding valve, after which the membrane begins to oscillate. This leads to pressure build-up and pumping of water.. Naturally, such mechanisms turn out to be sensitive to overheating, therefore, it provides for the presence of automation that turns off the engine when the water level drops. Such equipment is recognized as low-level, but it copes with its tasks perfectly.

It is important to remember that Malysh submersible pumps are of 2 types:

top water intake: this option is considered the most preferable, because the equipment will cool faster and will not suck up dirt;
units with a hole at the bottom: they need careful control, automation, a thermal protection system and a mechanical filter to prevent sand or debris from entering the pump.

Installation and connection

To perform a correct installation, you need to pay attention to the type of equipment:

pumps with a hole located at the bottom must be fixed at a distance of 1 cm.
equipment with a valve at the top is lowered to the very bottom.

Before installation, the end of the nylon cord is fixed on the pump housing, and to the other end it is necessary attach a medical tourniquet or rubber hose. Thanks to this solution, the resulting vibrations will be significantly reduced.

During operation, it is necessary to check that the submersible pump does not touch the pipe or well. In this case, an additional protection will be a rubber ring located on the body of the device. After reaching the depth, you need to fix the pump, and then connect the unit to the network.

How to extend the service life?

Almost always, a submersible pump is used in difficult conditions, so you should take care in advance to avoid equipment breakdown. In particular, it must be remembered that small debris, lime deposits and sand can get under the body, which means that the parts will wear out over time, and the pipes will become clogged, because of which you will have to buy a new submersible pump. To avoid this, you need to purchase a special filter that can trap solid particles. Such equipment is easy to install and protects the pump from the smallest particles, the size of which does not exceed 150 microns. Thanks to such an inexpensive filter, the life of the Malysh pump will increase significantly, and efficiency will increase.

In order for the device to last as long as possible, it is necessary to remember other important nuances.

The Malysh submersible pump is the best option for summer residents and owners of small garden plots. The use of such equipment will help solve the problem of water supply. In order for the unit to serve as long as possible, it is worth choosing the right power, following the manufacturer's recommendations and using the device carefully.

The presence of a home well or an equipped well on the site requires the participation of water pressure equipment for the unhindered rise of moisture for domestic needs. According to the recommendations of users, the domestic version of the submersible pump, which has the name according to its dimensions - "Kid" deserves special attention. Small in size, however, there is no reason to doubt the productivity of the unit.

"Baby" - the principle of operation, advantages and disadvantages

Units are classified as vibrating. The principle of operation is to create electromagnetic waves that act on the pump valve. The float, in turn, interacts with the membrane, which causes oscillations. Their strength is sufficient to create pressure and buoyancy pressure. Hence the benefits:

compactness. All parts of the unit - an electromagnetic core, a vibrator - are in a sealed enclosure. There are no remote mechanisms except for the electric cable. Dimensions allow pumping water from narrow shafts of wells, wells or hard-to-reach flooded places - "Kid" is used not only to deliver drinking water, but also to drain basements and storm drains.
Durability. It is due to the absence of rubbing parts that require regular maintenance and lubrication. The service life is estimated at several tens of years, given that the unit is maintainable.
Light weight. "Baby" is light - from 5 kg. Therefore, the installation will happen quickly, without the use of additional mechanisms and assistance. it will also be easy to extract it from a well or a well shaft.
Economy. Due to the low power, unlike centrifugal ones, the use of the Malysh submersible pump for country and residential needs is economically justified. True, with a caveat - in the case of a house of more than 100 square meters. m, year-round living and developed "infrastructure" - bathrooms, baths, sinks - a different version of the unit is required.

To be fair, the shortcomings should also be pointed out. This is the collapse of a well or well that is not reinforced with casing pipes. Vibration contributes to the fall of the soil from the walls, which in the future will result in clogging of the filter with dirt and water of the appropriate quality.

It is also important to mention that the pump cannot operate for a long time - more than two hours. Vibrating units are sensitive to cable heating. Low productivity and depth of installation are the accompanying qualities of the "Baby" - for this it is purchased.

Technical characteristics of the pump Kid

The range of models "Baby" is wide. Each option has its own technical characteristics for rational use for a specific situation. Consider:

Classic submersible pump

Designed to work in wells over 100 mm, lifting height up to 40 m and pressure transfer up to 150 m. The option is good for use in summer cottages and in small houses with year-round living for modest needs. Pump Toddler Specifications:

The concentration of suspended matter in water should not exceed 0.01% of the total mass, otherwise the coarse filter may not be able to cope and the unit will operate at full capacity, which is fraught with overheating.
The temperature of the pumped water is up to +35 C. It is not suitable for pumping liquids from warm reservoirs or flooding due to district heating.
Power - 245 watts. The unit operates from a 220 V network.
The performance is directly proportional to the lift - the deeper, the slower and less water is pumped. From 1 m - more than 1 cu. m, from 40 m - up to 500 l.
Safety of work - 2 hours.

Complete set of model – only the pump. Hoses, cables and cleaning filters are missing. In addition, it is important to pay attention - there is no pressure switch that protects the unit from idling and other protective automation.

Series "Baby - M"

It is identical to the classic units, with the only difference that in the first version the submersible pump is made with a lower water intake circuit, and the series - M - with an upper one.

"Baby - 3"

Depending on the financial capacity and the available source of water - a well, a well - namely, the debit of a resource - these models are selected, related to the budget ones. The differences from the basic configuration are as follows:

Reduced power. For reservoirs with a small influx of moisture, 165 watts is enough.
A small horizontal length - about 20 m. However, this is quite enough for country needs.
The pump is compact, and its weight is close to the minimum - 3 kg, which greatly facilitates installation.
In addition to the model, a hose and a filter are purchased. Power cable included - length 30 m.

"Baby - K"

Owners who care about the long-term operation of the unit, but for obvious reasons, who cannot pay fabulous money for the pump, are offered Malysh - K - a device that is indistinguishable from the classic unit, but has additional protection against overheating. With it, the pump is not threatened by emergency situations - long uncontrolled work, dry running.

Features of connecting the pump Kid to the well

The installation algorithm for any Baby model is simple, but responsible. To begin with, the depth of the location is determined - almost every series is designed for a small amount. Further, a supply hose is purchased with the required diameter indicated in the marking of the unit.

This is important, since a mismatch is fraught with engine overload due to the difference in pipe and hose cross-sections. Plastic clamps are used in the form of fastening. It is undesirable to mount the wire, since vibration is already capable of affecting the walls of the well, exposing them to destruction.

Other features:

Depending on the installed water intake circuit - upper or lower - the pump is installed directly on the bottom of the reservoir or half a meter from it, respectively. This is due to obtaining a clean resource - in the first case, water will go from the thickness of the column, in the second, the pump will not scoop up dirt.
It is impossible to observe the exact depth setting for the model, indicated in the marking as the lower dynamic level. This is the limit value, and the real parameter should be lower. Pumps "Kid", any series, are installed in a well or well strictly vertically.
The horizontal position will reduce the life of the unit and give a dirty resource - the filters will not cope with the constant movement of silted soil.
Before lowering the unit into the shaft, it is recommended to equip it with a coarse filter - all components are offered by sales offices. In case of omission, the submersible Baby is threatened with clogging of the hoses with soil, silt and mud. The pressure will increase, that hi, in turn, to system malfunctions. Automation in this case would protect it, but it is not offered in the kit.
It is recommended to lower the pump on a strong nylon cord fixed in an eyelet on the unit - it is fixed on the head of the source. To dampen the vibration of the pump, a rubber pipe or a piece of gasket is attached to the cable or cord. It is also recommended to purchase a kind of rubber cover for the case, if the diameter of the well does not allow the pump to be placed freely, and it is impossible to allow hitting the walls.

Pumping station from Malysh for the needs of a private house

The essence of complex equipment is the use of protective devices in addition to the pump. Like that:

check valve;

Let's consider in detail:

The check valve prevents the flow from becoming intermittent during the entire operation of the pump.
The pressure switch protects the hydraulic tank from drying out and maintains the desired water level for normal use.
The hydraulic accumulator restrains shocks that occur due to pressure loss and its salvo appearance.

In a word, the equipment serves for the long-term operation of the submersible pump, increases the comfort of use for the owners. It will not be difficult to equip the unit with the listed devices - they are all commercially available and will fit any "Baby" series.

Conclusion

Undoubtedly, "Kid" is not a panacea for solving problems with water supply for a private house or site - there are many other models for use in autonomous systems. However, this is a budget the price of pumps Kid start from 1500 rubles, depending on the modification) and rational acquisition is not inferior to the "famous" models in terms of consumption characteristics. Therefore, "Baby" is worth your attention!

The convenient submersible pump Malysh will help solve the problem of supplying water to many owners of private households and cottages that are not connected to the water supply. The electric pump Malysh is not a powerful device for pumping water from artesian wells, but it will quite cope with the tasks of lifting water from wells, small wells, open reservoirs.

The lineup

3 main models are produced under the Malysh brand, which differ not only in technical parameters and in the intake system, but also differ in scope.

The standard submersible pump Kid has a lower water intake. These units are designed for:
pumping water from far located open reservoirs;
drainage of flooded basements and lower floors;
pumping water to a minimum level.

If the name has a K mark, then additional thermal protection is built into the design. That is, there is a thermal relay in the case, which will turn off the device in case of overheating. Such equipment can be left unattended for a long time without fear that it will burn out.

If the name is marked M, it means that the body is made of durable plastic. By default, it is made of aluminum. Without a doubt, the aluminum case is more durable, but it costs more.

The design of the Malysh-M and Malysh-3 pumps includes an upper water intake. The Malysh M pump is similar in technical characteristics to the basic modification. The device Malysh-3 has significant differences from it.

Top suction devices are used to draw liquids from wells / wells. In these places, units with a lower water intake may fail if they are not equipped with an additionally installed filtration system. Electric pumps with an upper intake during operation do not suck in silt from the bottom, which can clog the system.

Application area

The vibration pump Malysh has gained wide popularity due to its good technical characteristics, inexpensive cost and ease of use. Compact and not heavy (weighing up to 3 and a half kilograms), the devices cope with a wide range of tasks.

They apply for:
uninterrupted rise of water from wells / wells with an internal diameter of 8 cm to 11 cm and from any reservoirs in which the ambient temperature does not exceed 35 degrees;
for pumping liquids from a distance of 100-150m, which is quite enough to provide a small area;
pumping water from the tank to the water supply;
creating a water supply for agricultural or domestic needs;
pumping flood waters from flooded basements;
filling/draining pools.

Gardeners also include these electric pumps in automatic irrigation systems for tending horticultural crops or spraying shrubs using spray nozzles. The water pump Malysh works with liquids in which the amount of mechanical impurities does not exceed 0.01%. These models are not suitable for pumping more polluted waters, as the parts are subject to increased wear, which shortens the life of the devices.

Construction and connection

Vibration pump Malysh consists of a hermetic case, inside which there is an electric drive and a vibrator. The inlets of the models are closed by a valve. The operation of the device is based on the power of alternating current, under the influence of a shock absorber, forcing the armature and piston to oscillate, simultaneously pushing water into the nozzle.

The reason for the popularity that the Malysh vibration pump deserves is also the fact that it can be used to create a full-fledged pumping station included in the auto water supply system. To do this, you will have to supplement the design of the pressure switch, a hydraulic accumulator and a check valve. The relay will help maintain the desired liquid level, as it will automatically turn on / off the pump when the water level changes. The pressure of the Kid will be quite enough even for the installation of an autonomous water supply system in a country house, which reduces the cost of organizing water supply.

Such a unit is highly reliable, largely due to the proven design. And if a breakdown occurs, then this is not a problem at all, because thanks to the wide distribution of spare parts, it is not difficult to repair the Malysh pump today.

Installation

It is very important to connect the Baby pump correctly. Its working position must be strictly vertical, without distortions. The submersible pump baby is fixed with a strong nylon cord, for which grooves are provided on the body. At the bottom of the unit, you need to hang a weight with a spring to dampen the vibration.

The pump body is separated from the casing pipe by special elastic cuffs or simply by a wide ring of dense rubber. Do not lower the electric pump on the wire, as it will resonate vibration, which will lead to wear of the fastening. There must be a distance of at least one meter from the bottom to the pump housing.

Pump Toddler Specifications

All modifications of the line work from a 220V household network. They can dive up to 3 meters deep. They are produced in several modifications differing in the length of the power cord, power and pressure.

In wells with a low flow rate, deeper lowering is acceptable. The water intake rate for all models is the same - 430 l / h.

Malysh, Malysh-M have a head of 40m - 60m, Malysh-3 - 20m - 25m.

Productivity increases when working without pressure up to 1 500l.

Electric pumps also differ in size and power.

The power of the basic modification Malysh and M is 240W.

Dimensions in length - 25.5 cm, and weight - 3.4 kg. The modification Malysh-3 has a lower power - 185W, the length of the unit does not exceed 24cm, weight - 2kg.

Electric pumps Malysh and Malysh-M can be used to lift liquids from wells with a diameter of more than 100mm from a depth of up to 40m, and Malysh-3 is designed to work with wells with a diameter of more than 80mm and up to 20m deep.

Where to buy a baby pump

It will not be difficult to buy a Baby pump due to its widespread use. The price of such a device, depending on the modification, is in the range of 1500 - 3000 rubles.

Baby water pump has the following advantages:
The location of the suction holes at the bottom of the body in the electric pumps Malysh allows you to pump water from the bottom.
The location of the suction holes on top in the electric pumps Malysh-M, Malysh-3 allows you to operate the device without supervision, since the unit will not overheat.
Electric pumps can also be used for pumping clean drinking water.
They do not require maintenance.
Long service life.

Video about the pump Baby

Household electric pumps are used to provide water supply to personal plots and small farms. Universal submersible pump Kid can be optimally used in places with low water consumption. The name Malysh electric pump was due to its compact miniature size and light weight. Despite the modest power characteristics, the kid submersible pump provides a fairly good water pressure, depending on the feed height.