Installing the fence from the chain grid. The fence from the chain grid: species for different soils and goals, how to make and install

Rabita is a good option to arrange the fence, and in a short time and without the use of some special tools. The final result will not disappoint the owner of the site, since such a fence is simple, practical and quite reliable. In specialized stores, the grid is offered to consumers in rolls that are not difficult to deliver to the venue.

How to do and where in demand?

Undoubtedly, in front of any subsidence and the owner of the private household questioned the question: how to make a fence from the challenges with their own hands? This material is in demand in each subsidiary farm.

Such fences are more appropriate to arrange in summer cottages, the grid can be covered with water bodies, poultry houses, cattle pens and other small areas that require fence.

Tip: In order to extend the timing of the grid operation, try to acquire a galvanized version.

Types of fence from Rabit

The fence from such a mesh can be 2 types:

Tension;
Sectional.

Tension fence

The device of the first option does not represent any complexity, as it does not need complex tools or does not require welding, it does not exclude the possibility of using and wooden supports (pipes).

It is enough to wear into the ground pipes, and what they will, round or square, does not have a fundamental importance.

Fencing from sections

In this case, the situation is different, as it is assumed to install a grid in a metal frame, after which a sectional installation of the fence is made.

If you need to build a fence in a short time, then use the first option.

Installation of tension fence

Let's start with what we will tell you what actions will need to take to build a tensioning fence from the chain grid.

Materials for work

At the initial stage, it is necessary to determine the amount of material that will be required for work;
You need to measure the perimeter of a fixed area, and for these purposes, four angular columns should be installed and skid through them, the length of which will allow you to obtain the necessary data.

Knowing the required amount of the grid, it is easier to calculate how to make a fence from the grid of the chain, how much the support columns and other utility materials are needed, such as:

Wood or metal pillars;
Fasteners (cable, durable wire);
Rabita grid itself.

In the construction market, such a mesh is represented in several varieties.

It is distinguished by its shape of cells and their size. But, if the first parameter does not play a special role, then in the second case, the large size of the cells will not suit, for example, in the case when the courtyard on which the poultry is contained. Since chicks will be able to break through such cells.

The height of the future fence from the chain grid is equal to the roll width.

Install columns

As already mentioned, the columns can be wooden or metal, the second material is more durable to use due to its high strength.

But the wooden columns are also a good material, because the chain grid does not differ in sailboat, only one end of the wooden pillar will be required (which will be carried in the soil) to handle a pre-special mastic with waterproofing properties.

Brief instruction will allow you to describe all the steps:

To make recesses for installing columns, optimally use a special boring, which can be both mechanical and gasoline.
The pillar's height depends on the width of the Rabent grid roll, that is, if this parameter is 2m, then the pole must be at least 2.95m.
Set the posts should be at a distance of no more than 2.5m, with the depth of their bumping into the ground from 70 cm to 1m so that the submerged part is 10-15 cm below the level of its freezing.
As soon as the pits are prepared, their bottom should be filled with small stone and rubble, to prevent the scholarships.

Tip: If we are talking about metal poles, then it is permissible to carry out concreting. To this end, you can prepare a mixture of concrete yourself. The standard option requires the connection of such ingredients as cement, sand, crushed stone taken in the ratio of 1: 3: 5, or to use the finished brand of the mixture No. 150.

If concreting is carried out, then the time is necessary to dry out - it takes 2-3 days.

Installation of grid Rabitsa

After the posts occupied their place, you can safely begin the installation of the chain mesh.

If an attachment is assumed to the wooden poles, then in this case, nails or special brackets are used.

And to the metal pillars, the grid is fixed with hooks, wires and welding.

It is necessary to tighten the chain in such a way that it does not send it later, that is, the most tight.

All the details can be viewed on the video.

Tip: Mesh tension should be started from any angular pillar. For preventing its sagging, you can skip a solid wire or fittings through the upper mesh cells and fasten them over the poles.

Selection section

In this case, almost the same materials are required as for the first option. Add Items for the manufacture of fence sections and such equipment as a welding machine. In this regard, both the complexity of installation work and the total cost of fence increases.

Manufacturing technology

A frame of the steel corner is welded;
Inside the frame is stretched and the grid is fixed;
Prepared sections are attached to the metal pillars, since there are no speech about wooden versions here, which requires welding.

It is more durable in its parameters, reliable and durable in comparison with tension.

In order to exclude the possibility of entering the pillars of water and excessive moisture inside, they are recommended from top to cover with special plugs. This can be done using independently manufactured items, or use industrial samples that are also played by a decorative role.

If a challenge with an anti-corrosion coating is selected for the fence, then its service life can reach 20 years. The usual grid without a protective coating may be unusable in five years, but this is one of the ways of saving funds if it is necessary to perform a temporary fence.

Conclusion

The chain grid as a fence allows you to quickly and reliably disappoint a plot with minimal cost and time costs. The price of such a fencing is small, it protects well from extraneous penetration, perfectly misses the light, without limiting the overview, and is excellent for enhancing adjacent boundaries between neighbors.

The grid is widely used in the fence of country sites. Set the fence from the grid of the chain chain can anyone, having a minimum of tools at hand. In compliance with the technology of installation and the choice of high-quality materials, such a fence will last 15-20 years. Before starting work, you need to study the types and characteristics of the grid, as well as study in detail the instructions in order to avoid errors.

The grid is made of black and galvanized wire, so the quality of the chain chain is different. Black wire grid is the cheapest and short-lived. It is covered with rust after the first fog or rain, and after 3-4 years it comes to full dissent. It is possible to extend the service life of the non-scattered challenge using paint or liquid rubber, which should be applied to the grid before it is installed, and then periodically update the protective layer.

The grid of galvanized corrosion wire is not afraid, and therefore serves longer. It costs a little more expensive black, but absolutely does not need protecting processing. Of the galvanized chains, it looks neat and attractive.

Plasticized Rabita is becoming increasingly popular. This metal mesh is covered with a dense layer of anti-corrosion polymer, thereby having increased resistance to atmospheric effects. In addition, the polymer is colored, the grid looks very attractive and aesthetically. And although such a challenge is quite expensive, the demand for it is constantly growing.

In addition to the quality, the chain grid is characterized by the size of cells, wire thickness and the height of the roll. Cells may have dimensions from 10 to 65 mm, the wire diameter is 1-5 mm. Roll height from 0.8 to 2 m, but the most sought-after - 1.5 m. The standard grid length in the roll is 10 m, the rolls are made at 20 m. The smaller cells, the more expensive the cost of the grid, because it increases the material consumption .

Type of grid Rabita	Wire diameter, mm	Mesh width, mm	Live cross section mesh,%	Estimated weight 1m2 mesh, kg
	1,20	1000	55,0	4,52
wicker Mesh with Rhombic Cell	1,20	1000	61,0	33,73
wicker Mesh with Rhombic Cell	1,20	1000	69,8	2,78
wicker Mesh with Rhombic Cell	1,40	1000	65,5	3,8
	1,20	1000,1500	75,3 (78,9)	2,20 (1,94)
wicker grid with a rhombic or square cell	1,40	1000,1500	71,5 (76,2)	3,00 (2,57)
wicker grid with a rhombic or square cell	1,40	1000,1500	76,3 (77,0)	3,24 (2,74)
wicker grid with a rhombic or square cell	1,60	1000,1500	73,3 (77,0)	3,24 (2,74)
wicker grid with a rhombic or square cell	1,80	1000,1500	76,0 (78,9)	3,25 (2,75)
wicker grid with a rhombic or square cell	1,60	1000,1500	77,5 (80,9)	2,57 (2,17)
	1,4	1000-2000	83,6	1,77
wicker grid for fences	1,4	1000-2000	87,0	1,33
wicker grid for fences	1,6	1000-2000	85,7	1,74
wicker grid for fences	1,6	1000-2000	88,0	1,39
wicker grid for fences	1,8	1000-2000	87,0	1,76
wicker grid for fences	1,8	1000-2000	89	1,46
wicker grid for fences	2,0	1000-2000	87,9	1,81
wicker grid for fences	1,8	1000-2000	91	1,1
wicker grid for fences	2,0	1000-2000	90,7	1,36
wicker grid for fences	2,0	1000-2000	91,7	1,23
wicker grid for fences	2,5	1000-2000	90,7	1,70
wicker grid for fences	3,0	1000-2000	89	2,44
wicker grid for fences	2,5	1000-2000	92	1,41
wicker grid for fences	3,0	1000-2000	92	1,74
wicker grid for fences	2,5	1000-2000	94	1,10
wicker grid for fences	3,0	1000-2000	93	1,53

Rabita grid prices

Rabitz

Types of mesh fences

The fence from the chain grid is sectional and stretched. The first option provides for the manufacture of rectangular metal sections, inside which the grid is fixed. For sections, metal corners, profile and round tubes of a small diameter are used. Connect them with welding or bolts, if not. Such a fence looks more aesthetically and attractive, the metal frame does not allow the grid to be saved.

Stretching fence to install faster and easier; Its design consists only of support pillars and the grid itself. Fasten the mesh with steel wire, clamps or hanging hooks on the folds welded to the columns. For pillars, pipes are suitable for different diameters, concrete columns, wooden timber.

Installation of fence columns

And for the sectional, and for the tensioning fence markup, the preparation and installation of the columns is made according to the same technology, only in the first case the poles must be stronger. This is due to the additional load from the metal sections; If the supports are too thin, the fence necessarily turns.

For work it will be necessary:

roulette;
wooden pegs;
motok thin rope;
building level;
manual drill;
crushed stone and sand;
solution;
profile pipes 60x40 mm;
bulgarian;
primer.

Step 1. Installing corner pillars

The reserved area is purified from vegetation if you need to align, the location of the extreme pillars. Experienced builders recommend angular poles from the pipes of a larger cross section than intermediate, and boil deeper. For example, if the intermediate supports take the profile pipe 40x40 mm, then it is better to take 60x40 mm for angles and 15-20 cm is longer.

Getting started to install pillars:

When the solution is slightly freezing, you can remove the struts and proceed to the markup for intermediate racks.

Step 2. Marking

Between the corner supports, the rope is tightened at a height of 15 cm from the ground - it will be a fence line. The line must be divided into equal segments corresponding to the width of the span. The optimal width of the span for the fence from the slave is 2-2.5 m; If you increase it, the grid will definitely offer. Retreat from the extreme pillar to the desired distance and drive into the soil pegs, and so to the opposite corner. All pegs should come into contact with a stretched rope and be on an equal distance from each other.

Video - a new way to install support pillars

Step 3. Installing Intermediate Supports

At the scene of the pegs, the holes under the columns and fall asleep with the bottom of the sand. To make more convenient to control the height of the supports, on the upper edge of the corner racks stretch another rope. Now the pipes are inserted into the pits, leveling in height and vertical, befened with rubble and soil and tightly tightly scramble. Top poured concrete and smash the surface.

If you plan to install a tension fence, and the ground on the site is quite dense, the intermediate supports can be simply scored in the ground and do not concrete. For this, the holes are dried on half the required depth, insert pipes there and clog the sledgehammer. To protect the upper edge of the deformation columns, take a piece of a larger pipe, welded a steel plate on one side and put on top to the column. After the pit supports, the pits fall asleep with rubble and sand, shed water to a better seal and a pretty tram.

Step 4. Welding hooks

About a week later, when the concrete is hard enough, you can continue the installation. Consign the grid on the pillars with wire or clamps, but it is more convenient to push it on the hooks. There are profile pipes with already welded hooks, but if there is a welding machine, cheaper to make them alone. For this, it will suit the segments of the steel rod, screws, nails, even a thick wire - everything you can tear to the pipe and bend. On the post 2 m height, it is enough to make 3 hooks: at a distance of 15 cm from the ground, 10 cm from the top of the pipe and in the middle.

Video - fence from the challenges with their own hands

Step 1. Mounting Mesh

The chain roll is set near the corner post, wound a little and put on the cells on the hooks. To securely fix the edge of the grid, you need to take a segment of the reinforcement with a cross section of 8 mm and a length of 1.5 m and to turn it into the first row cell. After that, the reinforcement attach to the pipe and weld. Now, when tensioning the roll, the grid will not be fed. Securing the end of the mesh, the roll is transferred to the next support, gently unwinding it.

Recovering the platform connections with a pipe 10-15 cm, the steel rods again fought in the cells. This time it is not necessary to weld it, it just helps evenly pull the grid. When the grid is hoping for hooks, the rod is taken out, the roll is unwinding another span, they again in the reinforcement and so until the very end of the fence. To connect two canvases, a wire from the extreme vertical row of one of the rolls is used.

Step 2. Locking the canvas from sagging

Even a well-stretched canvas over time saves a little, so at the installation stage you need to take care of the additional fixation of the challenges between the columns. It will take the wire with a cross section of 6 mm and the welding machine. The wire is fought in the second or third row of cells horizontally along the entire fence. In places of mesh adjacent to the columns, welded wire. Then the bottom edge of the grid is then strengthened, and the hooks bend in complete. Now the cloth of the fence is securely fixed on the supports and will not be fed and saving.

Step 3. Finishing Stage

When the fence is installed, you must complete the final strokes:

to wear plastic plugs on the pipes;
paint columns;
top mustache breakdown to twist on 2 turns and bend down.

On this, the installation of a tension fence is considered to be made.

Video - Rabita connection in one roll

Installation of a sectional fence

Production of sections

Step 2. Preparation of racks

From sheet steel, rectangular plates 20x5 cm and 4-5 mm thick thickness are cut. Take one plate, apply perpendicular to the post at a height of 20 cm from the ground and weld. The second plate is welded at the top, retreating from the edge of 15-20 cm. The plates on the rest of the supports are fixed in the same way.

Step 3. Installation of sections

The first section is put between pillars, lifted and exposed in terms of level. Then weld the sides to the plates and go to the next span. It is very important to correctly combine the sections in the height, so that the upper crossbars of the frame make a single line. After installing all sections, the places of welding are cleaned, grind and paint the frame of the fence.

Read step-by-step instructions, how to do in our new article.

Video - how to make a fence from the grid Rabit

Owners of country houses, summer cottages, as well as residents of the private sector in cities often face the problem of installing the fence. High quality fence on a concrete foundation requires significant investments of forces and financial resources. This can be justified if you have a big plot outside the city, where you want to reliably protect not only from neighbors and passing transport, but also from stray animals. Small sites within the city's city or in the country village most often wallpace with a chain grid, which does not shadow green plantings, and its installation takes a little time even without attracting professionals.

What do you need

To install the fence occupied as little time as possible, you need to prepare in advance and calculate the number of material and tools.

To mount the fence from the grid, you will need:

Rabita grid in countable quantity with a small margin.

Poles.

Wire for fastening the challenges to the columns.

Fasteners (plates, brackets, clamps, nuts, bolts) - depending on the selected method of installation.

A hammer.

Pliers.

Bulgarian.

Apparatus for welding.

Materials for the preparation of concrete (if necessary, pillars concreting).

To determine the required number of chains, pillars and other fasteners, the first thing is necessary to measure the perimeter of the part of the part. The simplest and most reliable measurement option - on the stretched cord.

To do this, you need to knots in the corners of the site, which will be covered, and stretch the durable thread, fishing line or wire, the length of which is subsequently and measured. The measurement result will be equal to the required amount of mesh patterns.

However, it is necessary to add a couple of reserve meters. Poles for the fence are mounted on average at a distance of two and a half meters from each other, but not closer than two meters.

Knowing the size of the perimeter of the part of the part, it is easy to calculate the required amount of supports and, accordingly, the approximate amount of fastening elements, which, however varies depending on the selected form of the fence design.

Types of designs

The main types of fences designs from Rabitsa:

Stretch fence without guides. The easiest in the installation and accessible by finance option. To establish such a fence, it is enough to wear the poles and cover them with a grid, attaching to the supports of the wire. For such a fence, there are pillars of any form from any material. This design is perfect for temporary fence or fences inside the site.

Stretch fence with guides. This species differs from the previous presence of two longitudinal guides, which can be both wooden (timber) and metal (tube). This design looks solid and better keeps the form, however, it is not recommended to install the fence with metal guides on the bunched soils due to the possible breaks in the primer of the soil.

Sectional fence. This type of fencing is a series of welded sections from metal welded to the columns, in which the chain challenge is mounted. The mesh frames are made by welding from a metal corner. Main installation is also carried out by welding method. Such a fence is the most sustainable, outwardly more presentable, however, and a more expensive option.

Grid

Today, the chain grid is produced by several species:

Neokinated. The cheapest and short-lived. Such a grid requires mandatory painting, because after a short time after installation will definitely begin to rust. Service life in an unfamiliar form - no more than three years. Suitable for temporary barriers. For more solid structures, it has been practically not used lately.

Galvanized. It is not corrosion, durable, easily mounted, not much higher than the cost of a non-scattered chapter, received widespread distribution and firmly occupies leadership among other types of sales.

Plasticized. This type of chain appeared relatively recently and is a wire mesh with a special protective coating. Combines all the positive qualities of galvanized grid with greater aesthetic. Very durable, but also more expensive.

Plastic. Such a mesh is made entirely of plastic and is available in different color solutions with different cell form. It can be used for inter-fences between neighbors or for fences within the site. As a fence from the street, the plastic grid will not work due to its insufficient strength.

Important! When choosing a plasticized chain chain, you should familiarize yourself with the quality certificate of goods issued for sale, since poor-quality coating may not withstand the tests by weather conditions, as a result of which cracks and detects.

Another criterion for the differences in the types of slaves is the size of cells. Basically, the size of the cells varies from 25 mm to 60 mm. However, there are and meshes with cell size up to 100 mm.

The most suitable for external fence is the size of 40-50 mm, and the bird yard is better to protect the grid with smaller cells, through which even the smallest chicks will not be able to crawl.

Deciding with the type of chain and the option of the option suitable in all parameters, it is necessary to carefully examine the roll for damage and deformations.

Even a small bentness or curvature of a wire when installing a fence may pour into a serious problem.

The edges of the chain must necessarily be bent. Moreover, the "tails" of the wire should not be shorter than half the length of the cell.

Did you know? The grid invented and patented at the end of the 19th century Mason Karl Rabitz, and at first it was used when the walls were plastered.

Pillars

The basis for the fence from the challenges is the pillars, which, depending on the type of construction and the soil beneath it, are either simply bought into the ground, or concreted.

For installation, the fence from the Rabits can be used the following types of supports:

Wooden. Since the tree is a short-lived material, such supports are suitable only for temporary fence. The undoubted advantage is their low cost. Before installing wooden poles, it is necessary to align in height and process the underground part of the non-water mastic. The above-ground part of the support must be painted to extend the life of its service. The desired wooden column size is 100x100 mm.

Metal. The most optimal type of support for the fence from the challenge. They are characterized by durability, reliability and durability and most often are a hollow circular profile (with a diameter of 60 mm) or a square section (recommended size 25x40 mm). Recommended metal thickness - not less than 2 mm. The processing of such columns is primer and painting. They are easily welded any fasteners. You can also buy ready-made pillars with hooks to secure the grid.

Concrete. Such supports can be made independently or purchased ready, especially since they are relatively inexpensive. By cons of such a type of support refers to the inconvenience of their installation due to the severity and complexity of the mesh fastening.

Step-by-step installation

Installation of the fence from the chain is carried out in several stages.

Marking of the territory

To place the territory for the future fence, you need to knock off pegs along the corners of the part of the part and pull the construction thread. At this stage, the necessary materials are also calculated.

Then it should be noted the places for installing the supports that will face apart from each other at a distance of 2-2.5 m during the installation of the tensioning fence. When installing the fence with the sludge or sectional fence, the step between the columns can be 3 m.

Installing columns

Starting the installation of the supports with the corners, which are recommended to wear deeper, since they will have the main load of the entire design. To install the pillar (take the basis of the metal), it is necessary to dig up in the earlier place either to drill the yum brown.

The depth of the pit must be 15-20 cm more than the depth of the primer of the soil. It is recommended to increase the depth of the pit on the clay and suglinist soils. At the bottom of the hole for water drain, it is necessary to pour 10-15 cm gravel, and on top of the sand layer.

Then the pole is installed in the pit, previously treated with anti-corrosion composition. If the design of the fence is light, and the more temporary, the supports can be installed without concreting.

In this case, after the post room in the pit, the free space is covered with alternating layers of stone and soil, each of which is carefully tumped. In the case of installing a sectional fence or tensioning fence with guides that will increase the load on the supports, the pillars are better slain.
For this, a cement solution of sand and cement is prepared in a ratio of 1: 2, in which two more parts of rubble are added after stirring. When all bulk parts are added and mixed, water poured.

In this case, it is necessary to ensure that the solution is not too liquid. The finished solution is poured into the pit around the pipe. Concrete is necessary to dying and compact with a bayonet shovel and leave up to its complete hardening, which is usually taken up to seven days.

After installing the angular columns, the rest are installed in the same way.

Important! It is necessary to control the verticality of the support of the support using a construction plunder. To make it easier to fit the pillars in height relative to each other, it is recommended to pull the cord between the corner supports at a distance of ten centimeters from the top.

Pulling the mesh and fixing on supports

Different supports use different types of fasteners. Fixing the grid on metal poles is carried out with the help of hooks and welding, brackets and nails are suitable for wooden poles, and the slave is fastened to the concrete supports of the chain or wire.
Consider in detail the embodiment of the mesh on the fence with metal pillars. Start tensioning the chain challenges from an angular pillar.

It will be more convenient to do this if there is a little more in the mesh cells than before the support, to turn the reinforcement for which two people will pull - one closer to the upper edge, and the second to the bottom.

The third person can fasten the challenge on the hooks of support. After that, the grid can be welded to the post, using a private one or more branches.

In case the roll ended between the supports, it is enough to simply connect the two closers of the chain, having reversed the extreme spiral element of one web, then the bracket is connected to both parts of the grid and insert the output element.

Important! To reduce the load on the corner supports, it is better not to go back with the grid, but, disconnecting the cell, fasten the chain with the help of a welding machine and stretch further by a separate web.

After tightening the chapter described above, in order to avoid saving the top edge of the grid, it is recommended to go through extreme cells a thick wire or fittings that should also be welded to the columns. The same can be done with the bottom edge. Such a fence will be stronger.

At the end of the installation of the Rabita, it is necessary to bend and weld all the hooks on the supports, as well as paint the poles to avoid corrosion of the metal. If you mount the fence by an urgent way, then painting the supports can be carried out before they are installed.

Installation of fence with guides is not much different from the simple stretch. The difference consists only that in addition to the grid, the guides are also welded to the supports.

Important! Stretching fence from the challenge cannot be installed on a blockage plot, because in the inclined position it is very badly attached. The exit from this situation will be the terracement of the site or the installation of a sectional fence.

The procedure for the marking of the territory and the installation of the supports for a sectional fence is the same as for the usual stretch. Metal plates are welded to the installed columns (width - 5 cm, length - 15-30 cm) at a distance of 20-30 cm from the top and bottom edge of the support.

Sections are formed from rectangular frames welded from metal corners (30x40 mm or 40x50 mm), into which part of the chain of the required size is welded with rods.

Sections are installed between the columns and are welded to the plates. After graduating from installation, the fence is covered with paint.

22 once already
helped

This article was created to provide information on the features of the installation of the fence from the chain grid with their own hands. Here you will learn from which the chain grid is manufactured, from which its quality and cost depends.

We provide a phased technology for the manufacture of ordinary and sectional.

Decide how to install supports, and which material is best suited for this purpose.

The fence from the chain grid is the best option if you need to protect the site. As they say, cheap and angry, and for a small segment of time, with minimal costs.

Rabita grid is a very flexible material, with which you can make rounded parts of the fence. The service life depends on the quality of the material, and ranges from 5 to 30 years, and even more.

Installation of the fence from the chain grid can be carried out by tensioning between the supports or sectional between the pile.

Material for pillars can be any:, metal, wood.

Types of Rabit Mesh

Installation of the fence from the chain grid by a sectional method It looks pretty attractive. At equal intervals and at the desired height, the support posts are installed.

Between them is attached stack. This method is expensive, but more reliable. Suitable for installation on uneven relief.

Reduce the maintenance of the fence from the Rabit You can, if you use reinforcement as a frame. Do individual items there is no need. You can stretch it in the mesh cell at the top and bottom, and welcome to the columns.

The best operational characteristics possess the posts for the collection of metal grid. To install them, you only need to handle the metal of primer and paint the part that will be trapped in the ground.

Metal columns can be welded any fastener. You can buy such pillars in any point of receiving metal products, decently saved at the same time.

Also, on the metal market there are pillars of supports already painted with special hooks for the construction of a sectional type. Their price is higher, but it is less thanmed with them. It is recommended to use a rectangular profile in operation, which is characterized by special strength due to rigidity ribs.

Wooden supports Also popular with accessibility and cheapness. But very often, the saying is triggered by "miser pays twice." Wood has a property to be subject to negative impact of atmospheric precipitation, it is very loved by various insects.

Pipes from asbestos cement also use support for fences as pins. They are strong and not very expensive. The cost fluctuates within 400 rubles per 1 m.

Poles for the fence from a brick grid as a support are extremely rarely used. It is very impossible to look together these two material. Monumentality of brick and light mesh, not very attractive combination.

In order to install brick supports It is necessary to fill a solid foundation. But, after all, as you know, the chain grid is used primarily because of its cheapness, and the brick poles contribute only to the increase in the cost of the project.

The same applies to the columns from. Yes, they are durable and durable, can stand in many decades. But they are also inconvenient to install, pouring under support.

Work on the installation of a fence from the chain grid with their own hands begin with cleansing the territory.

Marking. At the corners they put pegs and pull the lace between them. Then, mark the location of the columns, at a distance of 2 - 2.5 m. It warns the grid bending.

Calculate the number of columns, it is possible to divide the length of the fence section by 2 - 2.5. The total length is separated by the average. Example: side 35: 2 \u003d 17.5 pillars, 35: 2.5 \u003d 14. Choose a round number 14. 37 m: 14 racks \u003d 2.5 m.

Through the line of the stretched cord, they put labels and dig a deepening, the level of which should be lower than the water freezing point of 15-20 cm. These are exemplary indicators that differ in each individual area.

However, the recess must be at least meter. The mass of the fence from the chain grid is big, and if the pits are not deep enough, the design can be tamed.

Metal supports We are hammered by a sledgehammer, pre-laying the board or Phaneur. This is done to avoid metal deformation. The installation of the supports must be carried out in a single order, in order to build one line.

After the concrete base of the poles will freeze, you can begin the tension of the chain grid. On top of the pillars stretch the cord, determining the upper level of the fence. The grid is set in such a way that there is no contact with the soil, why the material will quickly cover rust.

Rabits fastening to metallic columns Made by welding, to wooden with nails every 15 - 20 cm. Asbestos-cement supports and concrete mesh, using wire or plastic clamps.

Fasten the mesh starts from the corner post, because it is not very comfortable to go back in the future. The grid roll is vertical and fasten with any convenient method.

For the convenience of work, you can stretch the rod and brew with welding with hooks. This will allow the grid tight uniformly. It is more convenient to work in a few hands: one person holds, the second unlocks, the third fixes.

In order to connect the edges of the challenges among themselvesYou need to pull out the wire from one edge to avoid the saving of the fence from the chain grid, through the cells are passed to the reinforcement or wire and fix it on the poles. Direct mustache on the challenge bend in order to avoid traumatization.

Technology assembling sectional fence from chain grid

Preliminary works are the same as described above. First of all, set supports from the selected material. To set the grid, the roll must be unwrapped and highlight the desired piece pulling out the wire.

To pull the grid between the supports follows:

in the extreme holes of the mesh, rods 4-5 mm thick;
weld on one side inside the corner;
from the bottom and above;
with the help of welding connect the reinforcement from the mesh securing;
the grid is stretched and fasten inside the island from the columns.

Reading time ≈ 5 minutes

To date, with all the variety of fences, little of the design could replace the fence from the chain net, made by their own hands.

Advantages of the fence from the chain grid

Very quickly and easily installed with your own hands;
Low cost;
The ease of construction does not require an enhanced foundation;
Misses light, it will not create conflict situations with neighbors due to the shadow being created;
Strict and unobtrusive appearance, which perfectly fits into any landscape.

Installation methods

The fence from the grid of the Rabita can be installed in two ways:

1. NormalAs in the photo above, when the grid is tensioning between two supporting columns. This method is at times cheaper and easier. It is recommended to use in cases where the goal is not to pursue an impeccable appearance, but you just need to install the fence quickly and cheaply.

2. SectionalAs in the photo above, when the finished sections of the fence are manufactured, in which the fragment of the chain grid is fixed. This method will cost the order more expensive, because it will have to get a metal corner, the price of which is higher than the grid itself, but at the same time the fence itself will be much more attractive and practical (for example, on the top of the fence it will be possible to hang a carpet, something to dry, etc.)

Materials

To install such a fence, we will need the following materials:

Metal poles 50x50x2x3000 mm;
Rabita grid (not galvanized, galvanized or plasticized);
Fastenings (nails, galvanized bolts);
Concrete M200.

Step-by-step instructions for installing a fence from the chain grid

So how to make a fence from the chain grid with their own hands?

I. Marking of the territory.

We begin work from drivening the pegs in the corners of the site and pulling the laces between them. We measure the length of the lace is the length of the required grid of the chain, it is also necessary to consider + 5-7% of the additional length "about the supply". Next, place the places of support, the optimal step is 2.5-3 m.

II. Installing columns.

In the event that, after the construction of the house there was a sufficient amount of wooden timber or other material that can be used as future fencing pillars; When the price for the "forest" in your region is at times cheaper than the metal profile, well, or you just need a temporary fence - then you should use wooden supports. The surface of the wooden bar must be cleaned from the crust, and it is also desirable to treat it with antiseptics and waterproofing mastic that will protect the material from rotting and pests. Cut the pillars follows from the calculation of the desired height of the fence, as well as the depth of the base of the base (the pit must be greater than 100-150mm from the depth of the soil; therefore, if you count on a two-meter fence, and the depth of the primer of the soil is 800 mm; m). But such supports will not be asked for a long time, so it is better to use metal pillars!

If you decide to build a thorough and durable fence - take care of the purchase of metal columns. The installation of such supports requires base concreting. The depth of the concrete pit should be 1/3 of the height of the fence. For example, if you planned to put a fence with a height of 2 m, the depth of the pit should be at least 1 m (also should be taken into account the depth of the freezing and the bunch of soils).

III. Rabits grid stretch.

To the wooden base of the fence is more convenient to penetrate the grid with nails.

Sectional fence from the chain grid do it yourself

The main difference of this method from the usual is the presence of a frame.

For the installation of a sectional fence from the chain grid, we need the following materials:

Metal pillars 50x50x2x3000 mm;
Rabitan Galvanized Mesh or Plasticized;
Corner metal bent 40x40x3 mm
Metal rod and lanes for welding
Concrete M200

Marking and installation of the pillars of the sectional fence from the chain is no different from its simpler counterpart, but with welding frames will have to sweat. If you do not have good welding skills, it is better to turn to a professional.