How to glue ceiling tiles on uneven ceilings. How to glue ceiling tiles: step by step instructions How to glue walls with ceiling tiles

Modern manufacturers offer a lot of finishing materials for the ceiling in any texture, texture and color. Ceiling tile is one of the most affordable materials for ceiling decoration and budget repairs. Can I glue it in the bathroom or on the walls of the room? The answers to these and other questions are given below.

Before gluing tiles to the ceiling, the surface must be prepared.

Preparatory work:

If the ceiling is whitewashed, it needs to be washed out, wallpaper - removed, paint - removed. The ceiling must be completely cleaned from the previous finish. If there are remains of old materials on the surface, in some cases this may endanger the quality of gluing new tiles.
All noticeable irregularities, sockets, pits and other defects must be eliminated with a filler mixture on an acrylic base or sealant. If this is not done, then in places of obvious irregularities, the tile will simply break or not lie down and a large amount of glue will not save the situation. If you paste over (using the word past up incorrectly) with a tile ceiling with small irregularities, the aesthetic appearance will be spoiled.
When the putty is completely dry, it is necessary to mark the ceiling. This is done with a chop thread. The diagonal is cast, the center is marked horizontally.

The gluing process itself is largely uncomplicated: the glue is applied to the tile either pointwise or around the perimeter and in the center, and the material is glued to the ceiling. If necessary, they can be customized and trimmed relative to the edge of the surface. Regardless of the chosen method of gluing, there are a number of specific recommendations already at the final stage.

Namely:

Overlapping the joints between the tiles is possible only after the glue has completely dried. Otherwise, the tile can be displaced, peeled off or damaged.
Do not cut the ceiling tiles too far from the wall, otherwise there will be gaps that even with a ceiling plinth will be difficult to close.
After the glue is applied to the tile, it should be kept for several seconds and only then apply it to the surface.

If, at the end of the repair work, after some time the ceiling color is fed up, the tile can be freely repainted in any other shade you like. Dispersion or acrylic paints are suitable for this. If you do not take into account the fragility of the emulsion, then this mixture is also quite suitable.

Ideas: how to glue ceiling tiles with a rhombus and in other ways

Methods of gluing tiles for the ceiling are in the options for its location on the surface. There are only four of them: in a row, a rhombus (diagonally), “bricks” (with offset), or in the form of a chessboard.

Let's consider each method in more detail:

Diamonds or diagonally. First you need to make the labels on the diagonal layout and perpendicular. You need to start sticking from the center. The advantage of the method is that it will help to hide the curvature of the walls. The disadvantage is a large amount of waste.
Way in rows - the simplest and most common. Tiles are laid parallel to the walls along perpendicular markings. The installation should also start from the center, but you can still from the window.
Checkerboard method includes the use of tiles in two colors. Installation begins from the center of the ceiling. Tiles are stacked in rows with alternating colors.
The method of "brickwork" or offsetmay include one color of the tile, two or more. The starting tile is laid from the center of the ceiling, the subsequent elements are shifted relative to the previous row to the side by half a tile or a third (quarter). Each row is performed with an offset.

The last method with offset looks interesting in several color schemes, if the use of a "rainbow" allows the interior.

Wet rooms: is it possible to glue the ceiling tiles in the bathroom

Ceiling tile is made from environmentally friendly materials, it is practical and unpretentious in care.

There are different types of tiles, they differ in the method of manufacture and technical characteristics:

Pressed (stamped) tiles are the most affordable and very widespread. They are a universal material for all rooms.
Cast elementscast in factories in special forms. This type of production is considered more reliable, and it is recommended to use it in rooms with a high level of humidity.

The process of finishing the ceiling of the bathroom is not much different from the standard gluing of tiles on the ceiling. After preparation, the surface must be primed for better adhesion. According to the markings, tiles in the bathroom can be laid in any acceptable way.

Options for using ceiling tiles on the walls

On the walls, ceiling tiles can be used as panels at the head of the bed or, for example, to decorate a fragment of one of the walls. A wide selection of textures, textures and colors makes budget decor very sophisticated. Americans have long been using this decor method.

There are several uses for ceiling tiles on walls:

As a decoration, instead of photo wallpaper with relief tiles, one of the walls is completely pasted from floor to ceiling.
You can completely paste over all the walls of the room with this tile, customizing the patterns.
Ceiling tile is an excellent budget option for wall decoration in patchwork tile. To do this, you must have tiles with different patterns and colors, the more options - the better.
The use of ceiling tiles as a material for a panel at the head of the bed or above a tea table creates an undeniable effect.

For walls, depending on the use case, ceiling tiles of any kind can be used, however, it should be remembered that the material is not resistant to mechanical damage and is capable of deformation.

Different ways: how to glue the ceiling tile (video)

When using ceiling tiles to decorate walls or ceilings, it should be remembered that the glue seizes quite quickly, so slowness will only interfere with work. In the process of gluing, it is important to monitor the docking of the plates and not leave gaps. Elements clipped to the walls are hidden by a skirting board. If you are finishing with different types of tiles, you should first lay out the pattern on the floor, then move the elements to the ceiling or wall. Compliance with the recommendations of specialists is a key rule, thanks to which even a beginner home master can make the right quality repairs.

Have a good experiment!

Technique of pasting the ceiling with foam tiles, different methods and schemes of fastening, the selection of suitable materials and useful installation tips.

Preparatory work before installation of ceiling tiles

It is necessary to start work on pasting the ceiling before wall cladding, since wallpaper can be stained with glue. However, if replacement of the finish on the walls is not planned, and the ceiling needs to be glued, then the wallpaper can be closed with plastic wrap. Almost any type of surface (wood, concrete) can be pasted with polystyrene ceiling tiles.

For reliability of fixation and durability of the coating, we prepare the ceiling:

We remove the chandelier and isolate the ends of the wires.
We get rid of the old finish. At the same stage, we tap the surface for the presence of unreliably fixed elements. At the corners and at the joints it is more convenient to do with a screwdriver.
We remove stains of rust, mold, fungus, soot and grease with special antiseptic solutions. If you skip this step, then all traces will eventually appear on the new lining.
We make a thick cement-based putty mixture and cover large cracks if present.
Priming the ceiling with a deep penetration compound with antifungal components. Please note that a deep penetration primer can be prepared at home by diluting the PVA glue in water in a ratio of one to three.
At the same stage, we evaluate the evenness of the coating. If the difference and potholes are significant, then we align them with a layer of starting putty. After that, we wipe the roughness with sanding paper and primed with an acrylic composition. If the irregularities are insignificant, then the tile itself will mask it.

The tile can be glued even on whitewashing, if the ceiling is even, but it is important that the whitewashing layer does not crumble and crumble. In addition, the whitewash will need to be primed before gluing to improve adhesion with the adhesive.

Types of ceiling tiles for the ceiling

In the process, we will need the ceiling tile itself and glue, on which we will fix it to the surface.

According to the method of production, tile happens:

Pressed. This expanded polystyrene ceiling tile is stamped. Its thickness is usually from 6 to 8 mm. Elements of this particular type are most often found defective.
Extruded. Issued in blocks. In the manufacturing process using a polystyrene strip with a film coating, which is intensively pressed. Products are more dense compared to pressed tiles, smooth and shiny surface, and their thickness is usually 2.5 mm. There are models that imitate wood, marble and other natural materials. Such a tile can be used to glue the ceiling in the bathroom, since it has improved moisture-resistant characteristics.
Injection. Products are produced by sintering the feedstock in special molds. In the production of granules are not destroyed. And therefore, in the end, a tile of the correct geometric shape with a deep pattern is obtained. Thickness - from 9 to 14 mm.
Seamless. Such a coating looks as aesthetically pleasing as it does not have visible seams. This material will cost more, but it looks more aesthetically pleasing.

Having decided on the type of ceiling tile, pay special attention to its quality. To do this, when buying, consider the following features:

Each element must be geometrically correct, the sides are even, the angles are 90 degrees. Otherwise, when gluing, there will be uneven seams and rows.
The finer the grain in polystyrene foam tile, the better it is. However, make sure that the product does not crumble or crumble at the edges.
The pattern should be uniform, without defects, and the pattern should be clear and symmetrical.
Traditionally, tiles are available in sizes of 50 * 50, therefore, it is not difficult to calculate the required number of elements, knowing the area of \u200b\u200bthe ceiling. Rectangular models of extruded tiles with dimensions of 100 * 16.5 cm are much less common.

Please note that it is important to purchase material with a margin of 10-15%. Otherwise, you will have to buy from the next batch, and it may differ in shade or other details.

Choosing adhesive for ceiling tiles

As for the adhesive for ceiling tiles, its selection should be taken no less seriously than the choice of tiles, because the longevity of the finish, reliability of fastening, and ease of use depend on it. It is important that it has a not too thick and not too fluid structure. Only in this case will it lie down with a thick and thin layer, which is very important if the ceiling has slight irregularities.

For gluing the ceiling with tiles, different compositions are used: putty, drywall adhesive, liquid nails, polyurethane or acrylic adhesive.

First of all, the choice of composition depends on the type of surface. The tile can be fixed to the aligned ceiling with liquid nails, polyurethane and acrylic glue. But if the surface is with irregularities, then it is better to use putty. It is evenly distributed over the surface and will ensure the reliability of fastening.

When purchasing materials, do not forget about ceiling skirting boards to mask joints with walls, a socket for a chandelier and other decorative elements.

Creating a drawing and marking the ceiling for tiles

Before starting work, you need to draw up a diagram according to which the tile will be fixed. The most common location options are: parallel, diagonal, combined (staggered, snake, around the perimeter).

Depending on the chosen method of placing the tiles, you need to mark the ceiling. To do this, you need a tape measure, a laser level and a chop cord.

We carry out work according to this instruction:

For parallel fastening of the marking line, apply from opposite angles. They should cross in the center.
For diagonal fastening in the center of the ceiling we beat off with a masking cord the lines connecting the centers of the opposite walls.
In parallel with two axial ones over the entire surface with a step of 0.5 meters (standard size of the ceiling tile) we draw lines.

Do not rely on the eye and start gluing without marking, because uneven gaps will completely ruin the result.

Parallel mounting of ceiling tiles

To start gluing tiles according to this technique, it is necessary at the wall opposite the door. And even better - from the most noticeable angle.

We carry out the work in the following sequence:

We apply glue around the perimeter of the inside of the tile and in the middle with a cross. It is not recommended to lubricate with an excessively thick layer. Otherwise, inaccurate marks will appear along the edges, and the seams between the individual parts will become much more noticeable.
Firmly press the tile to the surface and smooth it in one plane. It is necessary that the adhesive is evenly bonded.
The next element is first joined with the previous one and only then pressed to the coating. Please note that you must pay attention to the symmetry of the pattern.
In this way we glue the entire ceiling to the edge.
Having reached the extreme row, we measure with a ruler the distance from the seam of the previous tile to the wall and cut off the necessary part with a clerical knife. It is not recommended to cut off several at once. For each row, it is better to take a new measurement, since the walls can be uneven.

Upon completion of the process of gluing tiles, it is necessary to close the gaps with decorative skirting boards. They are usually made of the same material and sit on the same glue.

Diagonal installation of ceiling tiles

It is more convenient to start fastening diagonally from the center of the ceiling. If it is planned to install a lighting device in this place, then the edges of the tile will have to be cut off. In the future, the hole can be closed with a decorative plug.

In the process, we adhere to the following instructions:

According to the markup made, we attach the first tile in the center so that at each corner there is a line in the middle.
We fix the second part along the axes applied to the ceiling.
We glue the tiles along both axes from the center to the walls.
Attach the rest of the details.
For mounting on the extreme row, we cut out a suitable element, having previously measured the required distance with a ruler.

After the ceiling is fully pasted over, a damp cloth can remove excess glue near the seams and pencil marks if available.

Ceiling Tile Adhesive

The essence of this method is to fasten four elements at once and align them on one plane. It is most often used when gluing an uneven ceiling with putty.

We carry out the work in this order:

With a notched trowel, apply the adhesive to the ceiling under the area of \u200b\u200bfour plates. Using this tool allows you to immediately apply a layer of the desired thickness.
We attach four parts at once and we join them with each other.
Using a two-meter level or rule, we align all the elements relative to the ceiling and among themselves.
On a marked line, we lay a row of two tiles to each wall in order. In this case, the parts must be positioned so that their joint runs exactly along the axis.
We attach the remaining elements according to the marked markings.
The extreme row is made of harvested segments.

Please note that during the process of gluing the ceiling with irregularities, you must definitely use the building level. This method is a little more complicated, because it is recommended for beginners to initially smooth the coating with putty, then proceed to gluing the ceiling tiles.

The technology of fixing the tiles to the ceiling is not particularly complicated, and even with the right approach, even a beginner can cope with it. However, some tricks will help you avoid mistakes and greatly facilitate the work:

Before starting work, leave the tile for some time in the room where the installation is planned. This is necessary to adapt the material.
The combination of tiles of several colors looks original. Such a combination can be placed in a rhombus, in a checkerboard pattern or in another pattern, depending on your preference.
A small arrow is usually applied to the inside of the plates. Make sure that she looks in every direction on every detail.
So that the teeth do not form on the coating and the seam does not stray, it is not recommended to interrupt the process in the middle of the row.
If it is necessary to wipe gaps in some places, then this should be done only after the adhesive has dried. It is better to do this using putty or sealant. If the grout gets on the tile, immediately remove it with a wet brush.
The tile will be pressed closer to the ceiling if it is not held with your hands, but with a wooden block to evenly distribute the load.
In order to save costs for pasting, you can use transparent compositions on a liquid "rubber" basis. Their consumption is much less, however, in order for the part to fix firmly, after applying the glue to the tile, you need to wait a bit until it dries.
It is not recommended to install high-power lamps at a distance of less than 20 cm from the coating, since expanded polystyrene can melt under the influence of high temperature.
If you prefer foam tiles, then note that a water-based paint for its finish will not work, because it will begin to peel off after a year. The best option for these purposes is a dispersion composition based on acrylates.

Watch the video about installing ceiling tiles:

We figured out how to glue the ceiling tiles in several ways. With the help of step-by-step instructions, you can independently prepare the surface, choose the material and fasten in any way you like. Properly selected and fixed tiles will not look like a budget finish. Painting or combining several colors allows you to create an original ceiling design.

One of the important details of a quality repair is a beautiful and even ceiling. Some are limited to whitewashing, others acquire tension options. One of the popular ways is to glue the ceiling tiles. How to install so that the material is firmly held and decorated the room? A selection of helpful tips is provided in this article.

Material characteristic

Ceiling tile is a foam material. It is usually sold in squares, but there are also rectangular patterns. The most common size is 0.5 × 0.5 m. The front side is smooth and embossed, laminated or without any coating. The decor of the tile can imitate wood, fabric, ceramics, stucco molding and other structures.

There are three types of finishing material:

injection is obtained by sintering and molding polystyrene foam in special forms;
extruded is extruded from an extruded strip, usually film or dyed;
pressed is made by pressing.

There is a so-called seamless tile. Its advantage is that at the end of the work, the joints are completely invisible. Usually they have a curly edge: when glued, the wavy joints on the ceiling become invisible. Installation of such a coating is carried out with an accuracy of a millimeter and only on a flat surface.

Ceiling tile is a way to quickly and cost-effectively decorate a room. When the ceiling is designed in this way, it is called “glued” or “glue”.

Advantages and disadvantages

Why should you give preference to polystyrene tiles for the ceiling? Material Advantages:

It is environmentally friendly.
One of the key benefits is accessibility. Expanded polystyrene tile is inexpensive and is a common material.
A wide range of reliefs allows you to choose the option for any interior.
Suitable for finishing most basic surfaces: concrete, brick, wood, plaster and gypsum.
It has soundproofing property.
Helps to keep warm indoors.
Easy and quick to install with your own hands.
Allows you to easily correct the result after some time (for example, to glue the departed part).
Aesthetic look.
Helps to hide minor defects in the ceiling (potholes, cracks).
The material is not combustible, therefore it is allowed to glue near heating systems.
Such material is easy to care for: it can be cleaned and wiped with a damp cloth. If the coating is not laminated, then it is cleaned with a soft nozzle of a vacuum cleaner or with a dry cloth.

The material has a number of disadvantages:

It melts at temperatures above +80 degrees, so the lamps should not be located closer than 30 cm.
It turns yellow over time from sunlight.
Some coatings do not tolerate dampness.
On an uneven ceiling, it is difficult to achieve uniformity due to the abundance of joints.
Poor air leakage, which makes the room more stuffy.
Fragility: Thin sheets are easy to warp and damage until they are fixed to the ceiling.

What to glue

To finish the material for a long time, you need to choose a good glue for the ceiling tiles. The final result and the durability of the coating largely depend on the choice.

What to stick polystyrene squares on:

"Moment" - one of the commonly used compounds. Its advantage is that it dries very quickly, which justifies its name. It is enough to press the tile to the ceiling for a few seconds. Of the minuses, it is worth noting the high cost and high consumption.
- universal adhesive based on polymers. It is used for gluing tiles, ceiling skirting and other materials: linoleum, parquet, etc. After drying, it remains transparent, which ensures the preservation of the aesthetic appearance of the coating. It takes longer to “Moment”, so you have to hold the tile longer, which is not always convenient.
Eco-naset - glue similar to Titan. Plus - during operation, you can adjust the position of the tile. The minus, as with Titan, is a relatively long polymerization.

How to install

What items will be needed for a successful installation:

stepladder (or high steady table);
glue gun;
stationery knife;
ruler (tape measure);
pencil;
putty knife;
brushes;
twine;
rags for wiping;
protective gloves and mask;
glue and tile.

Training:

First, make sure that each tile is clean.
Sheets with bent edges and other defects are not used. For this reason, you should buy material with a small margin. A defect can be detected when unpacking the bundle, but even during installation, the material can easily be damaged by inaccurate handling. It is recommended to purchase a ceiling finish 10% more than necessary.
Before starting repairs, it is better to remove all the furniture from the room. If this is not possible, then large plastic bags will come to the rescue, which should cover items.
Close the windows, windows and doors - you need to glue the ceiling plates strictly at room temperature and without drafts.
Be sure to turn off the power to the room.
Make a rough drawing on a piece of paper to better orient yourself in the amount of tile needed and its location on the ceiling.

Preparation of the foundation is one of the most important stages. The surface should be clean and as even as possible. It is recommended to clean the ceiling from old finishes - plaster, whitewash, etc. A spatula will help to clean the ceiling. Then, if necessary, re-plaster or plaster and coat with a primer. The tile will hide minor defects, but noticeable irregularities are best eliminated.

Advice! Rinsing whitewash and primers to concrete is a difficult and long process, and also very dirty. When using glue with good adhesion it is allowed to wash off only whitewash.

The main methods for installing the ceiling plate:

parallel to the walls - the most convenient;
it looks very beautiful diagonally, but it will take more material and time to finish the edge of the ceiling (lies with triangles or incomplete squares).

How to glue the ceiling tile:

The first stage is the marking of the ceiling. Squares are glued from the center to the edges. How to quickly determine the middle of the ceiling? Pull two twine diagonally from the corners. The point of their intersection is the center. It should be noted. Next, two perpendicular lines are drawn through the point, which will divide the ceiling into 4 parts. Tiles will be fastened along these lines. To be sure, you can markup the entire ceiling, drawing the place of each detail of the coating.
The glue is applied to the sheets in a thin layer or spot using a special gun. The lower the weight of the material, the less glue you need to attach it. Pay particular attention to the edges and middle.
The first tile is pressed to the center of the ceiling, guided by the markup. Place the first four squares. Their angles should be in contact at one point, central.
Next, you need to stick other panels, focusing on the layout and position of the previous parts. All joints should be tight, without gaps.
Remember to remove excess glue with a damp sponge or cloth.
The tile placed against the wall is cut to size with a sharp knife, for example, a shoe or wallpaper, along an iron ruler or square. First, the desired part is cut out, and only then glue is applied.

What to do if the ceiling is uneven? In this case, gaps form between the tiles. It is easiest to wipe the seams with white acrylic sealant. After grouting, the excess is removed with a damp sponge.

Advice! If the tile closes the fixture for the chandelier, then make a suitable hole in advance, insert the wires into it and stick the tile. Remember to turn off the electricity before this operation.

Ceiling finish is completed by gluing the ceiling plinth. The glue for this material is used the same as for the tile. One condition: the composition must be transparent after drying. Otherwise, if accidentally hit on the front side, it will ruin the view.

A few rules for fixing skirting boards:

Start with the wall opposite the door.
Cornices in the corners are cut at an angle of 45 degrees.
Glue is applied on both sides: one is in contact with the ceiling, the other with the wall.
The gaps and joints in the corners are perfectly masked if you cover them with sealant.

For repairs to succeed, you need to take into account many points that not everyone can immediately remember. What you should know about ceiling tiles:

After purchasing and transporting, allow the panels to rest at room temperature to avoid deformation during operation.
Soft tiles at the time of gluing will be correctly held by a wooden block. The material is deformed by pressing with fingers.
Sometimes the dimensions of the tiles do not match each other. This is imperceptible to the naked eye, but manifests itself in the installation process. To avoid inconsistencies in the pattern, attach a square to the glued tile that is not oiled with glue. If the size is the same, then installation continues. If it does not match, you will either have to leave a gap, which you will later need to wipe with sealant, or (preferably) take another sheet.
Do not press too much styrofoam. This will not accelerate the setting of the glue, but may leave dents.

Gluing the ceiling is a crucial part of the repair. Successful completion of the finish is possible only with the right choice of glue, correct calculations and accuracy during installation.

Lightweight foam tile is the most sought after ceiling coating. With its help, they transform the space in kitchens, hallways, bedrooms and even in halls for receiving guests. First of all, people choose this finishing material because in comparison with stretch ceilings it costs mere pennies.

And, of course, everyone, without exception, likes the fact that even the person who does the repair for the first time in his life can cope with such a stick. For such newcomers, we will tell you how to properly tile the ceiling and what methods can be done.

How to properly and beautifully glue foam ceiling tiles: different ways

Scheme number 1

Scheme No. 2

For those who do not know the ceiling tiles - these are squares with perfectly even sides that have a front and back side. In view of this, when carrying out finishing work, you should carefully watch whether you fix them correctly on the ceiling.

After all, if you glue the tiles, not paying attention to this nuance, then in the end you will not be able to lay down the perfect picture. Also, when planning such works, it is extremely important to decide in advance which way you will glue the tile. This must be done in order to understand exactly how much material you may need.

Methods of sticking foam to the ceiling:

Parallel to the wall. This method of decoration suggests that the finishing work will begin to be carried out against the wall, which is located opposite the window or doorways. The first tile will need to be smeared with glue and lay it exactly parallel to the wall, slightly backing away from it.
Diagonally. If you choose this method, then you will need to start decorating the ceiling exactly from the center of the room. In order to determine this place, you will need to stretch the thread through the corners located opposite each other. The place where they intersect will be the center of the room.
Diamonds. I want to say right away that this method is considered the most difficult, so it’s better for beginners to not take it. In this case, you will also need to find the center of the room, put aside a few squares from it, and then glue the tiles diagonally from them. If you do everything right, then the corner of the tile will look exactly in the center, and one side will coincide with the diagonal on the ceiling.

How to mark the ceiling under the ceiling tiles?

Layout Recommendations

As already mentioned a little above, in order for the ceiling tile to look perfect, preliminary marking must be done before fixing it. Remember, if you do not want to redo all your work from the very beginning, you must do it.

Indeed, only correctly marked markings on the ceiling will help you place the first tile as it should, and subsequently create the perfect pattern. If you will fasten the tile to the ceiling with diamonds or diagonally, then the marking will help you mask the seams as well as possible, thereby making the canvas visually even.

First, use a measuring tape to measure the approximate distance (diagonally) from one corner of the room to another
Next, cut two pieces of rope (their length should correspond to the data obtained)
In the next step, you will need to stretch these two blanks from corner to corner so that they intersect in the center of the ceiling
Next, take, for example, a level and a simple pencil and draw the diagonals formed on the ceiling space, and be sure to mark the center point of the room
Remove the ropes and draw a square near the center point where the ceiling tile will fit easily. From this place you will continue to finish the entire ceiling.

Where to start gluing ceiling tiles?

It is necessary to start finishing the flow from a central point

If you carefully read our article, you probably understood that you can start gluing a plate to the ceiling from two places. If you are doing this for the first time, it will be better if you give preference to the method in which tiles are glued parallel to the wall. In this case, you will not need to carry out any preliminary measurements, and you can literally immediately go to the main stage of work. All you have to do is find the perfect place on the ceiling and fix the first plate on it.

After fixing it, you will need to check whether you placed it correctly, and you can proceed to fixing the rest of the decorative material. If you want to create a more complex picture on the ceiling, then you will need to mark it (we told you how to do it right above) and after that you can start transforming the living space. In this case, the first tile will need to be placed in the center of the room being repaired.

How to apply glue to the ceiling tiles?

Glue application

Most people who make repairs for the first time in their life think that applying glue to the finishing material does not require any special knowledge. But as practice shows, even such a simple, at first glance, process must be carried out correctly. If you apply glue randomly, then in the end the tile will not be fixed as it should and what is most unpleasant, the formed seams will not fit perfectly to the ceiling coating.

So, for a start, apply a small amount of glue to the very center of the tile, then put the droplets diagonally from this point, and at the very end, draw a line around the entire perimeter of the finishing material. When applying glue to the tiles, make sure that the droplets are not very large. If there is a lot of glue, then when you press the tile to the ceiling, it will start to go outside and as a result, you will have to remove the excess, and this can damage the structure of the finishing material.

Yes, and remember, if you want the adhesive to fix the tile to the ceiling as well as possible, before fixing it will need to be held in the air for 1-3 minutes. During this time, the adhesive will react with air and this will contribute to the fact that the substances that are responsible for adhesion will become more active.

Which adhesive is best for ceiling tiles?

Ceiling tile adhesive

As a rule, people think that the more expensive the glue, the better it is. Of course, in most cases, an expensive remedy is much better than a cheap one. But still, in the case of ceiling tiles, you need to pay attention to other factors. The most important indicator of glue quality is adhesive strength. The larger this figure, the more reliable the decorative material will be fixed on the ceiling.

In addition, you should pay attention to how quickly the glue dries. The faster this happens, the better it will be for you. After all, if it does not set in 30 seconds, but 2-3 minutes, then you simply get tired of holding the tile for such a time, and most importantly, you just won’t be able to fix it correctly. Also, when buying, be sure to pay attention to the viscosity of the adhesive.

If the glue you choose is very liquid, then try to choose another option for the finishing work. As practice shows, a too liquid glue base will not allow you to securely fix the tile on the ceiling and it is likely that after a while you will have to redo everything from the very beginning.

Types of adhesive for fixing ceiling tiles:

Universal
Titanium
Adhesive compound (silicone based)
Acrylic Putty
Liquid Nails
Polyvinyl acetate glue

How to beautifully and correctly stick diagonal ceiling tiles, rhombus: description, video

Before you start fixing the tiles, you must definitely prepare the ceiling space. If you do not do this, then in the end with all the desire you will not be able to fix the finishing material correctly. For this reason, it would be better if you first carefully inspect the ceiling and close up all the defects.

But keep in mind that in order for the tile to fit perfectly, it is not enough to repair all cracks and pits. If you want the maximum adhesion between the ceiling and the decorative coating, then you will definitely need to grind the surface and then carefully ground it.

First, measure the area of \u200b\u200bthe ceiling and figure out how many tiles you may need. Keep in mind that if you fix it with a rhombus, it may be needed more than if you glued it diagonally.
At the next stage, you will need to markup and designate the center point of the ceiling, as well as diagonal lines, equal to which you will lay out the diagonals and rhombuses.
After the marking is done, you will need to apply glue to the entire tile and fix it at a central point. If you want it to fix instantly, do not forget that it must be maintained for at least 1 minute.
In order for the tile to fix, it must be pressed to the ceiling and held in this position for 30 seconds. After you make sure that it does not move, you can start applying glue to the remaining decorative material.
Initially, you will need to lay out the tiles along the diagonals that were drawn during the layout, and when this is done, you can proceed to fill the empty space.
It is necessary to fix the tiles on the ceiling, moving from a central point to the corners, while trying to make sure that visually they fold into a perfectly flat line.

How to glue ceiling tiles seamlessly?

Sticking seamless tile

In principle, seamless tiles are glued in the same way that we introduced you a little higher. Therefore, in this case too, you will need to initially measure the area of \u200b\u200bthe ceiling in the renovated room, mark it, determine the center point, and only after that proceed to gluing the decorative material. But still, if you want to get the perfect ceiling coating, then glue the tiles either diagonally or parallel to the wall.

Yes, if you prefer the latter method of decorating the ceiling, then start fixing the tile on the wall opposite the window. Such a little trick will help you to make less visible those gaps that are formed when finishing with similar material. And finally, I want to say that, although some sources claim that in the case of seamless ceiling tiles, glue does not have to be applied around its entire perimeter, it still needs to be done.

As practice shows, if this is not done, then after drying, the gap formed during installation is quite evident. Well, of course, do not forget that the ceiling tile is made of very soft material, so you need to hold and smooth it not with your hands, but with a foam sponge or soft rag.

How to glue ceiling tiles on uneven ceilings?

Sticking ceiling tiles on uneven ceilings

As a rule, in old houses and apartments, ceilings are far from ideal. Most often they are covered with cracks and small indentations, which are very striking in the eye. If you live in a house with the same ceiling coating, then if you wish, you can fix the appearance of the house with ceiling tiles.

If you don’t want to tinker with leveling and grinding the ceiling, then just buy a foam tile and stick it in a parallel way to the wall. True, you must remember that you can do this if the defects on the ceiling are very minimal. If they are too large, then you will either have to decide to completely tear out the surface or to install a special frame.

Usually it is installed a little lower than the ceiling itself and this makes it possible to hide even very protruding defects. True, in this case, it will have to fix a more expensive tile, for example, wooden, metal or ceramic.

How to seal the seams between the ceiling tiles?

Seam Ceiling Tips

As already mentioned a little above, even the so-called seamless tile requires additional processing of the gaps that are formed after the ceiling fabric has completely dried. In view of this, when planning such finishing work, immediately lay in their cost special tools that will help you make the surface to be repaired as even as possible.

As for how to do this, in this case it is best to give preference to acrylic sealant. If you want to close the joints without any problems, then rub on the sealant in the tube and the gun, which will help you distribute it evenly.

Fix the gun on the sealant tube
Use a pair of scissors to cut the tip at an angle of 45 degrees
Press the hole to the beginning of the seam
Gently push the gun handle and guide it exactly along the seam
After filling the seam, carefully remove the gun from the ceiling and allow the sealant to cement

Can ceiling tiles be painted?

You can paint the ceiling tiles

Sooner or later, the desire to paint the ceiling trimmed with tiles appears in all people. But as practice shows, only a small part of beginning repairmen decide on this step. Most of these people believe that the paint will simply spoil the ceiling tiles and they will again have to spend money on expensive repairs. In fact, it’s not possible to paint the whole tile.

For example, in no case can a seamless tile be treated with coloring materials in such a way as it will necessarily make the seams darker and as a result, they will stand out quite strongly against the general background of the room space. The rest of the tiles can be painted calmly, though keep in mind that in order for the color of the updated ceiling to be as saturated as possible, you will need to apply the paint in at least two layers.

How can I paint foam ceiling tiles?

Ceiling Painting Scheme

As for the choice of paint for updating the ceiling, when buying it, you need to pay attention not only to color. If you want the ceiling to remain in perfect condition for a long time, you must choose the right coloring material.

And this means that it should prevent the growth of mold, be moisture resistant and have dust-repellent properties. In addition, it must have a moderate level of glossy effect. In view of all this, we can definitely say that it is best to paint ceiling tiles with water-based emulsion or acrylic paint.

Video: To how to glue the CEILING TILE quickly?

Styrofoam ceiling tiles are the most common, affordable way to upgrade a ceiling. Everyone tries to approach this responsibly and individually. Before gluing the ceiling tile, it is necessary to carry out preparatory work so that the beautiful ceiling coating, with the original finish, pleases the eye for many years. Choosing the option of decoration, everyone tries to approach this responsibly and individually. He tries to get acquainted with the varieties of this material, the rules for calculating the required amount, with which glue to glue, as well as some nuances of combining tiles with the interior of the room.

Types of Ceiling Tiles

On the construction market, ceiling tiles are represented by the following varieties, differing in the methods of their production:

Pressed tiles for the ceiling are made by stamping from polystyrene blocks. The thickness of the finished product min - 6 mm, max - 8 mm.
Extruded blocks are made from a polystyrene strip by pressing. They have a shiny smooth surface. The plates can be structured into a marble slab, a cut of a tree trunk and other natural materials.
For the manufacture of injection tiles for the ceiling, a method is used in which the feedstock is sintered. As a result, the product has the correct shape with a deep pattern. Its thickness is from 9, but not more than 14 mm.

The choice of ceiling tiles according to physical parameters

In order to properly glue the ceiling tiles, at the time of purchase you need to pay special attention to the geometry of the product. If a tile is selected with squares, then all its corners should correspond to the required parameters, that is, equal 90º. The slightest deviation in the future will lead to the formation of uneven seams. Corners of ceiling tiles must not be rounded or wrinkled.

Another indicator when choosing a ceiling tile is the material from which it is made. When buying polystyrene tiles, it is necessary to ensure that the edges do not crumble, and all grains are the same in size. Better quality is considered one in which the grain size is especially small. Expanded polystyrene plates should not break under its own weight if it is held at any of the corners by weight. The selected ceiling tile should have a clear pattern. No flaws are allowed, any minor inaccuracy or dent will immediately attract attention.

Calculation of the required amount of material and the choice of glue

After choosing the type of ceiling tile according to its physical parameters and external design, it is necessary to determine how much tile will be required for the entire ceiling area. More experienced owners immediately buy 10-15% more in case of rejection due to broken corners or errors during trimming. In general, the calculation is not complicated. You need to know the area of \u200b\u200bthe ceiling and the size of each element. Typically, ceiling tiles are available in sizes of side faces 50-50 cm. If the size of the ceiling is not a multiple of the length of the side of the tile, then there will be gaps at the edges of the ceiling when finishing. Therefore, when calculating this nuance must be taken into account.

Advice from an experienced craftsman: if you want to save on glue, instead of liquid nails, it is better to use transparent glue with a more liquid “rubber” base. Its consumption is significantly lower. But for a firm hold, be sure to dry the adhesive already applied to the tile a little.

After calculating the required number of tiles, you need to decide what glue to glue. A lot of people use “Titan”, “Econaset”, “Liquid nails”, “Moment”. They adhere well to any surface and dry quickly. After gluing, the tile holds tight. Only for this it needs to be pressed for a few seconds to the ceiling.

Work order

Many owners of apartments and private houses prefer to stick ceiling tiles with their own hands. Therefore, it is important for them to know that work should begin with marking the center of the finish area. To do this, from diagonally located corners, it is necessary to stretch two threads. Their intersection is the desired center. If a chandelier hangs in the room, then you can start work from this point. In this case, the docking angles at the lamp wire are slightly cut off. As a result, they will be closed with a curly glass of the rod of the chandelier.

Many start work from one of the walls and row after row of tiles. This option is the simplest and fastest. But here there is a slight nuance. The first row is best laid from the wall opposite the window or front door. Then gaps that are covered by partial fragments will not be so noticeable.

Before proceeding to the sticker, the ebbs at the edges of the product must be carefully cut. At the same time, the surface of the ceiling will be perfectly smooth, without seams. It is also necessary to strictly observe the symmetry of the pattern at the joints of the tiles. The slightest deviation violates the integrity and beauty of the finish.

There are relatively many options for arranging ceiling tiles relative to the walls of the room. The most common are parallel and diagonal with respect to the faces of the intersection of walls and ceiling. You can choose plain, color and combination tiles. Of the combined styling options, the following are most often practiced:

alternating or intersecting diagonals,

staggered

a snake

around the perimeter of the ceiling or in its center, etc.

At the end of the work, skirting boards are installed around the entire perimeter. They are glued with the same glue as the tile itself.

Options for gluing ceiling tiles to whitewash

We will glue directly on whitewashing, so you should choose one of two ways:

The first is that a primer is applied over the old whitewash. It is absorbed into the layer of the old coating and seizes with the main surface of the ceiling. Then you need to wait until the primer has completely dried and proceed to the finish.

The second method involves the partial scraping of the falling off whitewashed layer with a spatula. As a result, a layer of glue of a larger thickness is applied to the underside of the tile, and it is pressed for several minutes to the place of gluing. The glue is absorbed through a thin layer of whitewash remaining on the ceiling and seizes with the ceiling.

How to glue ceiling tiles with your own hands: video tutorial

Renovation of the ceiling is time-consuming and expensive. In addition to tiles, you can arrange tension and suspension structures, mirror panels of various configurations and sizes. Here everything is decided by the financial possibilities and fantasies of the owner.

(No ratings yet)

Discussion:

Andrey said:

I just cleaned the whitewash of the place where the glue will be applied. I bought superglue (putty glue sold by sellers in operation proved to be so reliable). I smeared with them only the places of the sticker at five points, pressed it to the ceiling and that's it. The tile holds. I didn’t close the seams - there wasn’t much need. Then the ceiling plinth - and that’s it. The ceiling is pleasing to the eye. Better than any whitewash. And faster and cheaper than suspended and suspended ceilings.

Svetlana said:

She glued tiles with her husband to the ceiling in the living room on their own. Now I know what to look for. An important note - it is important to process the seams with the correct material. We needed to take silicone immediately, but we confused and took white glue. As a result, our joints turned yellow after drying, the ceiling looked terrible. The only solution was to paint the ceiling with paint to close the seams.