Do-it-yourself gas forge forge: how to make a mini forging device from improvised means. DIY tin can forge DIY tin can forge

Dear friends and visitors of the site "", from the presented material you will learn how from a simple tin can make a small and full-fledged horn. Yes, yes, it is a forge, with the help of which it will be possible to heat the steel to red and forge, for example, a knife ... Today, the blacksmith theme is quite popular, both among young people and the middle generation. Work with metal has been respected since ancient times, the profession of "Blacksmith" was the most respected among the artisans of antiquity. Even when enemies attacked the city and destroyed all living things around, the Blacksmith was not touched in any way, but taken to himself (willingly or not). History was forged by blacksmiths.

In order to subjugate the recalcitrant metal, it must be naturally heated to red, and this can be done with the help of a forge from a tin can. An ordinary canned food can is taken as a basis, the walls inside are made of chamotte clay 1-1.5 cm thick. A hole is made in the upper part for installing a gas burner nozzle. M-6 bolts and pipe trimmings are used as legs. The stand can be made from plywood or board.

And so, let's look at what is needed to create a forge from a tin can.

materials

tin
chamotte clay
gas-burner
metal pipe 22 mm
M-6 bolts
nuts
board 25-30 mm
gas cylinder
dichlorvos bottle

Tools

hacksaw for metal
drill
putty knife
ruler
hacksaw
wrench
pliers
brush

Step-by-step instructions for creating a forge

First of all, you should familiarize yourself with the drawing and the diagram shown in the photo.

A tin can or a paint can is taken, as well as 2 bolts for making legs, 3 pipe trimmings, two of which will go to the legs, and one will be installed in the upper part of the can exactly in the middle with a slight slope. Can be used as a stand regular board 25-30 mm.
The legs are screwed on like this.
Pipe cuts are put on the bolts and screwed to a wooden plank.
Attention! The pipe cut in the upper part of the can is installed at a slight slope. The gas burner nozzle will be inserted into this tube.
Then you need to create heat-resistant walls inside the tin, for which you need to use fireclay clay.
The wall thickness should be 1-1.5 cm. The clay is diluted with water in a container and brought to a homogeneous mass, and in order to form a cavity inside the jar, you need to insert a dichlorvos balloon into it and fix it with adhesive tape. The mixture is poured inside, it is also necessary to tap the walls so that everything spreads evenly.
The clay will harden for about 4-6 days, after which a hole needs to be made in the back, it is necessary for long parts.
After that, a gas burner is inserted into the hole and the clay is hardened, everything is also tested.
Thus, it is possible to heat the metal to red and forge any object.
As a result, the horn from a tin can was painted in golden color, it turned out quite aesthetically.
As you can see, there is nothing complicated in making a forge, everything is extremely simple and clear, the materials are affordable and budget. If desired, the child will also collect. By installing it in your garage or workshop, you can forge small parts or knives. Now let's watch the video and consolidate the material covered.

Thank you very much for your attention! Come back often, we have a lot of interesting information.

A compact and easy to manufacture forge forging metal (knives and other products) is offered by “lawyer Egorov”. You can make it from a simple tin can and gypsum with your own hands.

To work, you only need a screwdriver or drill. The blowtorch that is used in this forge is one of the cheapest. The author of the video tutorial bought it for 750 rubles. Now you need to screw the plumbing coupling into the resulting hole. To be able to use a thread, the hole in the jar must be smaller than the diameter of the thread.

You can cut a ring out of the pipe and use it as a washer. It is best to use a standard plumbing nut.

Next, you need to make a tight connection installed clutch and neck blowtorch. The neck of the blowtorch exactly matched copper pipe 1/2 inch. The author had a connector for such a pipe and he pressed it into the coupling using a vise.

It remains to drill 2 more holes in the bank for two bolts - legs and fix these legs on the support.

The final stage is the application of a thermally insulating gypsum layer on the inner surface of the can. Gypsum hardens very quickly (1.5 minutes), so before cooking gypsum mortar, it is useful to prepare all the necessary parts and tools. It is necessary to prepare a cylinder (an aerosol bottle is convenient), which will form the cavity of the furnace, a spoon, water and other details.

First you need to mix gypsum and sand in a 1: 1 ratio. After adding water, knead the solution until a homogeneous mass, like thick sour cream. Put the resulting solution in a jar and insert a cylinder inside to form the cavity of the furnace. To make it easier to remove the cylinder later, you can wrap it with wax paper.

Until the cylinder is removed and the gypsum has not hardened, it is necessary to make a channel for the flow of gas. Gypsum rises within 1.5 minutes. It remains to dry the forge and you can start working on it.

The productivity of such a hearth is small and without a brick plug, its operation will be wasteful. With it, the performance, that is, the heating rate, increases significantly.

It is better to ignite the gas not in the furnace, but in the socket of the blowtorch. That will be safer. Horn - a source of increased danger! Do not leave a burning forge unattended. Forging on such a hearth occurs at a temperature of 700 degrees, the metal does not heat up quickly.

I am fond of blacksmithing and already long time I wanted to bring some of it to my suburban garage. After watching several thematic videos, I understood what to do, but did not find any step by step instructions on this topic, so I decided to write down for you how to make a forge forge with your own hands.

Do-it-yourself mini-forge assembly time from start to finish is about an hour and a half.

Step 1: Gathering the necessary things

You will need:

Can
wooden block
Pipe connector - 1.5 * 5 cm
Two L-brackets
Two wood screws to secure the brackets to the wood block
A pair of small metal screws with washers and nuts to secure the jar to the brackets
Sand
gypsum
Large bag for mixing plaster and sand
Conventional propane torch with spiral gas nozzle
Protective glasses
Fire extinguisher - just in case

Step 2: Preparing the Jar

Drill two holes about 1.5 cm from each edge of the jar.

On the opposite side of the holes, about 2-3 cm from the back of the jar, drill a 1.5 cm hole for the pipe connector, at a slight downward angle.

Step 3: Screw the Brackets to the Wood Block

Measure the distance between the holes in the jar and screw the brackets to the tree accordingly.

Step 4: Attach the jar to the brackets

Secure the jar to the brackets using screws, washers and nuts.

Step 5: Insert a Pipe Connector into the Jar

Just screw it inside, everything should look like in the photo: link. Try to think over the position of the tube so that when the burner fire begins to flow through it, it does not rest against the walls of the vessel, but smoothly exits the tube and twists in the jar - this will increase the efficiency of the melting installation.

Step 6: Create the Heat Resistant Filler

Mix gypsum and sand in equal proportions, add enough water to achieve the consistency of wet clay. We used a 350 ml plastic mug and in our experience for a large tin we advise mixing 3 mugs of sand and gypsum and adding 1 - 1.5 mugs of water to the mixture.

You need to work very quickly, as the mixture begins to instantly set and harden.

Stuff the jar tightly to 3/4 of its volume, and then make a hole in the middle with a radius of about 4 cm (for example, using a spoon), leaving walls about 2 cm thick. Choose a wider cavity at the back (bottom) of the jar to create best zone heat retention.

Use the back of a spoon or other thin object to clean the protruding pipe connector from the sand/gypsum mixture. Clean all surfaces with a damp cloth and let the mixture stand for about 30 minutes.

Later, I came up with the idea that you could stuff the pipe connector with paper, and use the pipe from under the can to create a hole in the can. toilet paper and stuff the heat-resistant mixture around it, and then all the paper will just burn on the first calcination.