What can be done from the wheels on the site. Crafts from tires for the garden with your own hands (photo)

Nowadays, more and more people are concerned about reducing the amount of garbage. Not the last role in this is played by the reuse of various end-of-life items, especially in the country. This is not only environmentally friendly, but also saves the family budget, and also allows you to show your creative abilities. One of the most accessible materials for making country crafts is old tires, which can be taken for free at any car service or tire fitting. Tires are used to make furniture, flower beds, warm beds and a variety of crafts that make the summer cottage unlike the neighboring ones and decorate it.

Do-it-yourself tire crafts in the country: everything from preparing a tire to choosing a location

Starting any work, it is necessary to select the material and tools.

Cooking tires

The thinnest European-made tires are considered the most convenient for cutting and arching. And also experienced craftsmen advise using winter tires - they are softer than summer ones.

Before starting the creative process, tires must:

What tools will be needed

May be useful:

Cutting a tire is a rather laborious process. It is not always possible to choose a knife of the required strength; not every summer resident has a jigsaw. Those who have preserved old sickles in their household, which are now rarely used for their intended purpose, can use their “antiques” to cut the tire.

Video: an interesting way to cut a tire with a sickle

Step by step instructions for making a flower basket

Such a basket can be used for low flowers, since there will not be much land in it. The airy design will look good on the terrace or near the porch of the house.

Procedure:

We prepare the tire as described above.
We cut out a template from cardboard, put it on the tire, circle it.
You can not use a template for drawing a simple pattern if the master has a good eye
Cut out the pattern with a jigsaw on both sides.
It is easier and faster to cut a pattern on a tire with an electric jigsaw than with a knife
We put the tire vertically, mark the middle on its upper edge and saw the surface in half.
We turn the tire.
We twist the long ends and fasten with self-tapping screws.
To twist the tight ends, you will need physical strength, sometimes it is better to do it together
We drill drainage holes in the bottom of the basket.

Video: a master class on making a flower basket from a tire

Collections of figurines from tires to decorate a summer cottage

Human imagination is limitless: flowerbeds, garden figurines, decor items and even furniture are made from old tires. Characters from fairy tales and exotic animals can live on the site. In cloudy weather, a cheerful sun from a tire will cheer you up, and rustic-style utensils painted in polka dots or flowers can compete with flower beds.

Tire animal figurines

Animals, birds, fish and insects made from used tires can be placed near the playground, if it is available in a summer cottage, or in a recreation area. Be sure to paint them in bright colors, then they will delight both adults and children.

Photo gallery: animal figurines in a summer cottage from old tires

A red-yellow crab will look good next to a red brick house. To make a funny bee, you will need three tires, wire and plastic for the wings. A green-yellow turtle is in no hurry. with experience A proud peacock will decorate any flower bed A bright red puppy can be placed on a playground The most traditional tire craft is a swan figure A bright butterfly can serve as a decoration and basis for a flower bed

Fairy tale characters from tires

In summer, many summer cottages are home to parents with children or grandchildren with grandparents. An excellent gift for the beginning of the holidays will be figurines of characters from your favorite fairy tales and cartoons.

Photo gallery: figurines of fairy-tale characters and cartoon characters from old tires

It is very easy to make a mischievous octopus from a cartoon about an octopus dad and his children. A donkey with a cart is a whole artistic composition from oriental tales. To make a funny hare, you will need several tires of different sizes. it's not boring to wash Cheburashka's muzzle and ears are carved from the bottom of large plastic bottles Mikhailo Potapych from Russian folk tales guards the site Even a child can make such a frog princess from three tires: you will need a tourist rug, old hoses and plastic buckets The head of the famous Wolf from the series “Well, wait a minute!" can be made from waterproof OSB or thick iron sheet

Other Tire Figures

Crafts from tires can serve as elements of the decor of the site. Bright figures are often used as flower beds. And if you glue the bottom, also cut out of the tire, you can make an original water container from a cup or teapot. Rubber retains heat well, and this water is suitable for irrigating greenhouse plantings.

One of the simplest figurines is a sun made of tires and plastic bottles. It is done like this:

We paint the tires with yellow or orange acrylic paint.
To paint the tire, you can use a special paint for rubber, which is sold in spray cans.
Pour the same paint into the bottles and shake well. After the paint has evenly covered the walls of the bottles from the inside, remove the corks and put them to dry.
We put the tire, which will be the sun, on another tire-stand (we also pre-paint it) or dig it into the ground.
We cut out a circle from plywood (10 mm) or thick metal (up to 5 mm) and attach it to the tire using self-tapping screws.

With a little free time and unnecessary tires left, you can easily create crafts from car tires for the playground with your own hands. We will provide you with ready-made ideas, photos and diagrams that clearly show how to cut and make toys and products for kids. Usually, in the territory of the post-Soviet countries, tires are used to protect school and kindergarten territories, courtyard flower beds. We offer several fun options for crafts that will decorate the playing area and bring the kids to complete delight!

Variants of children's crafts from old car tires.

Sandboxes

One of the most common and easy crafts to make is a children's sandbox. To create it, you can use either one large tractor tire (convenient for one child under 5 years old), or several tires from a car.

To make a sandbox, you will need the following materials:

Tires (one or more).
insulating material.
Spray cans with waterproof paints of the desired shades.
Washed sand.
Shovel.

It is convenient to make a sandbox for one kid from one big tire. To protect from the sun, you can install an umbrella in the center.

Step by step process:

It is necessary to dig a recess along the diameter of the future sandbox. It will help to fix the tire and reduce its height if you are using a large tractor tire.
At the bottom of the recess you need to lay insulating material. Its use will allow the sand not to mix with the ground, prevent the germination of weeds and the ingress of insects into the sand from the ground.
The tire must be washed and covered with paints for outdoor use.
Next, it remains to install the tire in the recess and fill it with sand.

If several small tires are used to create a sandbox, they will first need to be cut with a jigsaw and laid in the selected shape.

In such a large sandbox-flower, it will be convenient for several kids to play.

A flower-shaped sandbox made from several tires is a convenient option for several children.

Swing

Another popular craft, so beloved by all kids, is the swing. There are several options for how to make them.

Option 1

For the manufacture of this type of hanging swing, you will need a reliable support in the form of a structure made of wooden beams or a metal frame. The tires must be cut into two parts, painted and tied with a strong cable to the support at the two edges.

Hanging swing on a metal support.

Option 2

The next version of the hanging swing is more suitable for older children. They are made as simply as possible - a strong rope is attached to the tires placed horizontally or vertically by a metal hook and suspended from a support. Usually a strong tree branch acts as a support.

For the manufacture of swings, it is important to choose undamaged, durable tires that can easily withstand the load when riding.

Hanging swing from whole tires.

Rocking chair-balancer

Another favorite type of swing for children is the swing-balancer. And tires are perfect for their manufacture. Usually balancers are created in the form of horses, but you should not be limited to any shape or color.

A bright balance beam with jumpers for riding two kids.

Such a balance horse is suitable as a toy and decor for a playground, but if you remove the wooden base, the horse can be used for riding.

Horse balancer.

If you attach a steering wheel from an unnecessary bicycle to the balancer, you get a great toy for a child, which will be comfortable to hold on to while riding.

Balancer, stylized as a bicycle.

Vehicles

Crafts from cars, tractors and trucks for the playground will delight the kids! Products can be of varying complexity depending on the skills of the master.

Machine made of wheels and a plastic seat.

Figures of animals and characters

Making figures of animals and characters is another original idea for using tires in the playground. Obviously, kids will not be able to play with such products, but they will organically fit into the exterior of the playing area and will definitely cheer up both children and adults.

Snowman from car tires.

Arrangement of a sports and playground

A children's playground can be completely made of tires. In addition to the elements already listed (ordinary swings and balance beams, sandboxes, figures), various obstacle courses, transitions, and climbing elements can be made from unnecessary car tires.

The snail train can serve as a bench or a climbing simulator for the little ones.

A simple walker in the form of a snail for the little ones.

The walker in the photo below is already more complicated in design, therefore it can be used by school-age children. The manufacture is as simple as possible: you need to attach the tire halves to the vertical supports with screws.

A walker of a more complex design in the form of steps to a slide.

For many elements of a children's playground, tires do not even have to be cut. It will be enough to securely attach them to metal or wooden supports.

Climbing element of their tires and pipes.

The next climbing element is created very simply from painted wheels, metal supports and planks.

Option for manufacturing a climbing element.

From car tires, you can build a kind of simulator if you attach them one after the other with ropes (metal chains) to a wooden support.

Tire walking and balance trainer.

Thus, if you have a few old tires stale, do not rush to get rid of them - you can make original crafts for the playground with your own hands from tires in just a couple of hours, and according to our diagrams and photos, you can easily understand how to cut and assemble original products for playing area.

You can find more craft ideas from old car tires in the following video:

( ArticleToC: enabled=yes )

Crafts from old tires will bring a unique zest to garden design. You can make a heron from tires, flower beds, figurines of animals and birds. They will decorate playgrounds, territories of various institutions and schools. In addition, their manufacture is not expensive and quite simple.

To make a flower garden, you need (just that!) Paint tires of different sizes in a bright color, put them in a slide.

To give the structure strength, self-tapping screws or screwdrivers that fasten the tires along the inner surface will help. After that, earth is poured inside each, having previously covered the tires from the inside with geotextiles. A multi-tiered beautiful flower garden is ready.

A single-tiered flower bed resembling a camomile looks no less beautiful. But the tires for it will have to be cut.

This is not easy to do. Although, having a sharp, strong knife and strength, it is quite real. It is recommended to lubricate the knife blade with grease so that the rubber does not "jam" the metal. It is better to use a grinder or a jigsaw with a solid steel blade and a reverse tooth.

Video: Do-it-yourself flowerbed of tires

Flowerpot on a leg of tires

To make it, one sidewall is cut along the tread, then turned inside out. The work requires physical strength, but the result is worth it.

Another option is a flowerpot with a curly edge. To get the same "petals", they are marked with chalk.

Used to create flower beds and combined methods.

We turn out the tire

The tire is difficult to turn out: stepping on the inside with their feet, they take the edge with their hands, pull it up, trying to make some part turn out. Then, they continue to twist the rest, standing on the already “succumbing” (so that it does not turn back).

When the process is completed, the tire is painted in the selected color.

Made graceful tire heron, flamingo, swan, stork, turtle, owl, elephant, etc. instantly transform the site.

From tires that have worked out their service life, rides for children and even furniture are made. - chairs, armchairs, tables.

Crafts from tires for the playground is, first of all, a frog that children really like. You just need to paint a couple of tires green and cut out paws from scraps. Tires from baby carriages and plastic glasses are suitable for the eyes.

What they don’t come up with from tires: donkeys and crocodiles, dragons and bears, giraffes.

The fairy-tale hero dragon is supposed to scare away uninvited guests and pests, but he is so charming that he is unlikely to cope with the task.

The boys will be very pleased with crafts made from tires that have served the allotted time and continued their professional activities in “retirement”: guns, cars, tractors, etc.

Racing car

Multi-seat sports car.

It is good for kindergarten playgrounds

But, the boys will be delighted with the tractor.

Summer cottage furniture

Such children's chairs look cool and cheerful, so they will become a favorite place for kids to relax.

Adults will like chairs with a back and a small table more.

Video: Tire furniture for summer cottages and gardens

Exquisite tire lamp

It seems to sound very ridiculous. But he's really great!

How to make a stork out of tires

Many people would like to make storks out of tires - guardians of plots and symbols of happiness. In any case, the idea is to the liking of the country dwellers. After all, this bird nests where good people live.

Considered a symbol of tranquility, prosperity and peace, this bird will bring them to the owner. At the same time, he will receive the title of "jack of all trades."

materials

Required for its manufacture:

tire;
durable and sharp knife;
paint (black and white);
metal bar;
brushwood.

Step by step manufacturing

The first thing to do is to cut the tire into the desired dimensions. So, you need to choose the right tire. Nobody makes a giant stork, so tires from a large SUV are not considered an option. It is quite enough to make a stork out of tires, wheels from a passenger car.
You need to cut the workpiece in such a way that, by folding the pieces, you get the body of a stork. Details are painted white, and black "feathers" are made in the upper part. The halves are fastened together with steel wire and pliers.
To make a beak, you need a steel bar, a chisel and a hammer. The rod is cut to the desired size - these are the legs. Now you can bend your head. These two parts are painted with paint that matches the color of the bird.
To make a stork out of tires, confidently standing on its feet, holes are made in the lower abdomen. There are inserted rods, pre-cut. From the brushwood indicated in the brushwood consumables, a nest is made - a dwelling for the bird, which is fixed at the feet of the "owner".

Similarly, you can make a heron from tires using rods for the legs.

Making a swan

The swan is another favorite character made from car tires. If you know the tricks of its manufacture. The swan is graceful and very similar to the original.

While tires are new, they provide motorists with comfort and safety on the road. Having served their time, their lot is recycling or turning into toxic waste. However, with a creative approach, they are turned into real works of art: animal figurines and fairy-tale characters, flower beds and even garden furniture.

In the manufacture of figures, the main thing is the correct markup.

It is difficult to cut the tire along the drawn lines, but if you want to get a beautiful sculpture, you need to do it very accurately.

After the wings are cut out, they must be turned out. You can stop there. But many carve feathers out of rubber or use plastic bottles for them, which are attached to the net.

To get the desired bend of the neck, a metal plate is screwed to it with screws, which will not be visible after painting the bird with paint. If the swan is placed on a nest, the figurine is also attached to it with self-tapping screws to give stability. And then the swan turns out, as in the next photo.

For the manufacture of poultry, the “baldest” tire with a nylon cord is chosen, since it is easier to cut it than with a steel cord (breaker). In addition, after cutting, the latter has sticking sharp ends, which are easy to get hurt. If it has a longitudinal pattern - this is another plus. Having found a tire with the appropriate parameters, it is cleaned of contamination - washed and dried.

Tools:

roulette;
drill;
drill 3 and 10 millimeters;
knife with a sharp blade;
pliers;
grinder and electric jigsaw.

Materials:

metal rod (1.2-1.5 meters long);
dye.

Tire cutting works are carried out outside the home, therefore, you will have to be patient and wait for a fine day.

markup

In the example given, R13 wheels are used, the width of which is 165 millimeters and the diameter is 180 centimeters. They begin to mark up by drawing two lines that divide the tire in half. This is the future neck of the stork.

Then, the “beak”, “head” and neck are sequentially drawn on the tread part. If the center line on the tread is visible, the markings are greatly simplified. Well, in the absence of such, it will have to be applied with chalk.
The length of the beak drawn from the first line. It is 8-9 cm. Almost half the width - 3-4 cm. For the head, the length and width are 7 and 8 cm, respectively.
The head ends with a neck, which gradually expands towards the body, at the base being 8-10 cm. The marking of this part of the body ends on a line dividing the tire in half.
The tail remains. And it is already partially outlined. This is the fork resulting from cutting out the beak. Having drawn two parallel lines (width of the head) 30 cm long from it at a distance of 8 cm, we have a finished tail.

cutting blanks

It is carried out from the base of the neck towards the head. You can do it in several ways (depending on the material of the tires and their wear). The thinned tire is cut with a shoe knife. To cut a thicker tread, a grinder is used. You can, after making several holes with a grinder, finish cutting using a jigsaw.

Practice has shown that a file with frequent teeth pointing upwards simplifies the process. The operation is carried out at low speed. Another important point is that it is not advisable to carry out the process of cutting with a jigsaw first from one side, and then from the other side, since vibration will greatly interfere. It is more correct to conduct it in parallel - in sections of 4-5 cm.

Having finished with cutting, carefully process the edges. In the presence of a metal court, you can’t do without a grinder. For the cultivation of parts made of nylon cord, a knife is enough.

How to give the neck the desired bend

First you need to give the wings a proper span. To do this, the tire is turned inside out.

Having spread its wings, the bird is still lying on the ground, limply lowering its neck. To strengthen it, you need a steel bar. To realize this, paired holes are drilled symmetrically to the center line. Their diameter is 3 mm. Drilling starts from the center of the head with a distance of 15 cm between the pair to the tail.

To ennoble your site with beautiful flower arrangements, it is not at all necessary to buy expensive outdoor flowerpots. A unique frame for flowers of various shades and shapes can be made by hand. We decorate the cottage with flowerbeds from tires: interesting ideas and options for making flowerpots will help make the garden plot unique and inimitable.

Features and Benefits

By making a flower bed from a tire, you can realize almost any creative idea. Making such a budget option for framing flowers on the site is quite simple - just show a little imagination and make a little effort. Tire beds have a number of advantages:

tires are durable;
tires tolerate temperature extremes well;
almost any paint fits well on the rubber surface;
no need to spend money on material: almost everyone can find an old tire;
improvised items can be used as decorative elements.

Due to the fact that rubber is a fairly pliable material, the tire can be given a variety of shapes. You can paint the product in absolutely any color. Such a product can be used not only as a decorative element, but also as a functional attribute of the site. For example, in such flower beds you can plant small seedlings.

Design

You can make a flower garden using ready-made examples, or using your own original ideas. You can supplement the finished design with any available materials: it all depends on your imagination and skill. The process of creating a flowerpot is often not completed after cutting and painting the tire. A product of complex shape in the form of an intricate figure must be supplemented with decorative elements. When making a flower garden, you may need the following materials:

decorative and natural stones;
construction metal mesh;
plastic bottles;
remnants of various building materials;
colored glasses.

From several flower beds you can form bright compositions. A combination of multi-level flower beds of various shapes looks more impressive.. A popular option is a composition of flower beds in the form of cups and a teapot. For its design, you do not have to turn the tire inside out and cut out patterns on it. It is enough just to arrange several tires of different sizes, form handles from pieces of rubber and paint the finished products.

Unusual

In the children's play area, flower beds in the form of animals or fairy-tale characters will be appropriate. You can make a turtle from a tire and tread:

the protector must be cut into four equal parts;
in the tire you need to make 4 cuts under the paws of the turtle;
pieces of the protector are inserted into the holes and fixed with staples.
the tail is made from a small piece of rubber, fastened with wire staples;
the turtle's neck can be made from a polymer pipe.
a crumpled paper head is attached to the neck with adhesive tape.
all structural elements are painted in the appropriate shades.

Other materials can be used to make the turtle's head, neck, paws, and tail. The product can be decorated with additional items (for example, put a small hat on the head of the turtle, and glasses on the nose).

Flower

Near the house, flower beds that look like a flower will look good. Before you start making such a flowerpot, you need to decide on the shape of the petals. Petals can be in the form of a triangle, semicircle, rectangle or wavy. Sometimes they are narrow at the base and wide at the edges.

On the outer surface of the tire outline the contour of the petals. For marking, you can use chalk or a felt-tip pen. Using a shoe knife or jigsaw, cut out the petals. If the rubber is quite dense, and a knife will be used as a cutting tool, it is recommended to periodically dip the blade in soapy water during the cutting process.

Grasping the edges of the cuts, you must carefully turn the tire inside out. The finished product needs to be painted. Flower-shaped flower beds look more attractive if you use different shades of the color palette when painting.

On a leg

From a solid wheel (tire with a disk) you can make a magnificent flowerpot on a leg.

The workflow for creating such a flower bed consists of the following steps:

in the tire, reaching the tread with a cutting tool, cut out the petals of the desired shape;
then the upper and lower parts of the tire are turned out (the disk does not need to be removed - it will be the leg of the flowerpot);
the upper part is painted in saturated colors, the lower part will be a kind of stem if it is painted green.

Swan

One of the most common options for flowerbeds from tires is a product in the shape of a swan. Such a flower bed is made in the same way as a flowerpot in the shape of a flower. The difference will only be in more complex cutting. You can use the ready-made scheme, which shows the lines of the wings, tail, neck and head of a swan for applying to the tire.

After marking the tire, the very shape of the swan is cut out. Next, you need to unscrew the tire and complete the formation of the swan. The beak can be made of rubber or any other convenient material, painted with orange paint and attached to the head with self-tapping screws. The eyes of a swan can be made from pieces of electrical tape.

Usually the figure is painted white, but no one forbids the use of other shades (you can make multi-colored plumage).

A master class on making a swan from tires, see below.

Required Tools

To start making flower beds from tires, you need to prepare the necessary tools. First of all, this is a tool that will be used for cutting rubber (knife, electric jigsaw, grinder). If you decide to use a knife, the blade must be sharpened well. It is worth considering that cutting thick rubber with a knife is quite problematic. To make your job easier, the blade must be lubricated with grease before cutting. If the knife will not be used as the main tool for cutting the tire, it can be useful for making small cuts.

Using an electric jigsaw as a cutting tool would be the best option. The more powerful the jigsaw, the easier it is to cut the wheel. For cutting tires, a quality steel blade with a reverse tooth is ideal. Cutting a tire with a grinder is much easier than with a knife or jigsaw. The disadvantage of this tool is that the rubber at the edges of the cut will be melted, the cutting procedure will be accompanied by an unpleasant pungent odor.

If for the manufacture of a flowerpot it is necessary to cut the protector, it is better to do it with a grinder.

Then you should decide on the type of paint for the flower bed. Almost any paint fits well on rubber. The following types are mainly used:

aerosol;
oil-based enamel;
nitro enamel;
car enamel.

If necessary, prepare a brush to paint the tire. You will need gloves to work, they will protect your hands from paint or other possible contaminants.. To apply the markup, you will need chalk, marker or soap. In the manufacture of complex figures, some elements will have to be made from improvised materials. To fasten additional parts to the main figure from the tire, you will need staples, self-tapping screws.

How to do?

Making complex figured flower beds from tires is a laborious process that requires patience and some physical effort. Whatever shape you want to give a flower bed of tires, the procedure for making a flowerpot will always be almost the same. Here is a step-by-step instruction by which you can independently make a figured flower bed from tires:

We choose a tire. So that working with rubber does not cause unnecessary trouble, you need to take tires that can be easily cut (old, heavily worn, winter thin or imported).
Thoroughly clean and dry the tire.
Decide on the form. It is necessary to mark the cut line with chalk or a marker. The marks on the tire must be done as carefully as possible in order to facilitate the process of cutting out the figure in the future.
Cut along the drawn line, and then take out the upper part. You can use a high power jigsaw.
We turn the tire inside out (you need to take hold of the cut edge with your hands, having previously stepped on the middle of the tire and pull the rubber towards you with force).
We grind the cut edges and process them with gasoline.
At the end, the flower bed should be painted, dried well and, if necessary, decorated with additional elements.

View

All flowerpots from tires can be divided into two main types: solid and cut. The simplest option for a flowerbed of tires is a tire in its original form. You can improve the appearance of such a flowerpot using paints. Such flower beds can be placed in small groups, or made up of a multi-level structure.

A multi-level design will look more attractive if you give it the shape of a pyramid. To do this, you need to take tires of different diameters and install them on top of each other. The difference in tire diameter should be at least 20 cm. Hanging flower beds will be a more interesting solution. A hanging flower garden can be placed along a wall or a blank fence. The shape of such a flower bed can be very diverse.

The inner space of the tire must be filled with soil. As a drainage, you can use a mixture of small stones and sand. When making a hanging flower bed, several small holes must be made in the tire so that excess moisture can drain freely. Flowerbeds in the form of plants, animals or mythical creatures are more laborious, but they look quite impressive.

With the help of a tire and a cutting tool, you can realize any author's idea.

In addition to dividing into two main types, there is an additional classification of flowerpots from tires. Flower beds are divided by size and shape as follows:

high;
low;
single-tier;
multi-tiered;
curly;
round.

Material

The ease of manufacture of the flower bed, as well as its appearance, will depend on the material chosen. When choosing tires, you need to consider the following features:

the process of making a flower bed will be easier from old tires, worn rubber is more pliable;
imported tires are thinner than domestic ones and are more amenable to cutting;
winter tires are more flexible than summer tires;
tires with a metal cord are more difficult to cut;
if in the manufacture of a flowerpot it is necessary to turn the rubber inside out, you need to select a tire with the most worn out tread.

A flower bed can be made from rims or solid (rims with tires) machine wheels. Such material is used much less frequently than the usual tires, but flowerpots made of disks look no less attractive. Whatever material you choose to make a flower bed, it must be thoroughly rinsed from dirt. This can be done with a garden hose.

Clean material will facilitate the process of making a flowerpot and will not spoil the cutting tools.

In addition to the basic rules for making flower beds from tires, it is important to know some of the subtleties of its placement on the site. It is better to place a flower bed on a well-lit and relatively flat area. In large areas, multi-tiered structures will look better. Having decided on the placement, under the base of the flower bed it is necessary to make a container from boards or other solid material.

It is important to prepare good soil for flowers. The soil mixture should not be too oily so that moisture can easily pass to the roots of the plants. It is important not to forget about the drainage layer, which can be made of expanded clay or gravel. To retain moisture in the soil and facilitate plant care, the area around the flowerpot should be sprinkled with gravel or sand.

It is better to paint the wheels in light colors: this will avoid overheating of the soil in the summer. When painting, also consider the following:

Before painting, the tire must be thoroughly cleaned, dried and degreased. You can treat rubber from fatty contaminants with a solvent, gasoline or acetone.
It is advisable to cover the tire with paint in several layers. A thin layer of paint can quickly wear off or crack. Applying many layers is not worth it, this will lead to a quick peeling of the paint. It would be optimal to paint the product two or three times.
If you want to plant bright flowers in a flower bed, it is better to paint the tire in delicate light colors. In flowerpots of bright colors, it is better to plant light, small flowers.
It is acceptable that the shade of flowers echoes the color of the flower bed.
Painting a flower bed is not only from the outside. If you capture the inner edges with paint, the flower bed will look more voluminous.
The flowerpot does not have to be painted in one color at all; interesting patterns of a different color can be applied to the tire.

To apply the pattern, you can use pre-made stencils made of cardboard.

Turning things that have served their purpose into various pieces of furniture and decor has long become the norm. Many people no longer look at old tires, pallets and plastic bottles as garbage, but only as building material. Perhaps, after reading our article, you will also join them, because today we will talk about what amazing tire crafts you can do with your own hands.

How to make crafts from tires with your own hands.

Let's start with not just beautiful, but with beautiful and useful. You can make a lot of functional things for a garden plot from used tires.

How to make garden furniture from tires with your own hands master class.

Old tires need to be washed and cleaned. For cleaning, you can use a special tire cleaner - then your tire will take on a shiny black look.

We paint the side surfaces of the tire with acrylic paints. For a more interesting look of garden furniture, we can paste over the side surfaces of the tires with leatherette and paint it.

To get rid of the black gloomy color, first we paint our entire workpiece with white. Then we apply our drawing with colored paints. And, finally, we add clear dark contours to the drawing.

For the middle of our ottoman we make a round pillow. In order to apply color painting on black leatherette - fill the place under the drawing with white paint, and then apply a color pattern on top of it.

How to make an ottoman with a knitted cover from an old tire master class.

If for garden furniture made of tires, its resistance to weather conditions was important to us, then for a gazebo or terrace we can make another beautiful version of an ottoman from tires.

We attach the legs to the tire cleaned from pollution.

We knit the side surface for our ottoman. If you don’t know how or don’t want to knit, then for these purposes you can use parts of an old sweater.

We fix the knitted fabric on the tire on the side and bottom. We close the upper hole in the tire with a circle of plywood.

We crochet a round knitted part for the top of the ottoman with a side part.

Interesting options for crafts from tires.

There are other simple options for tire garden furniture. We can stack the tires on top of each other and make seats and armrests out of scraps from the top of the tire.

Or another version of tire furniture. Wooden spacers are inserted inside the half of the tire and a soft roll is sewn in - so you have a comfortable seat for the chair.

Crafts from tires for children.

From tires it is easy to make devices for playgrounds. For example, here are such simple swings.

Or a car that will not leave any kid indifferent.

Flower beds from tires with their own hands.

Very often, old tires are used to create flower beds and outdoor flower pots. So to speak, cheap and cheerful. A flower bed can be given a more decorative look by decorating its edges in a more interesting way.

To make such a flower bed, you should mark the side of the tire as shown in the photo. And then just cut along the line.

The cutting process itself can be tricky. Ideally, this is best done with a jigsaw. If you cut with a knife, then lifting the cut with a wooden peg, you will greatly facilitate your work.

The cut tire must be turned out. It's easier to do it together. But you can turn out the tire and one, stepping on the edge of the tire with your foot, and turning the other edge with your hands.

Such flower beds can be varied and original - this is what helped them gain great popularity. The most famous option is to put the tire on a stand that we cut earlier from its top.