Spinner at home. How to make a spinner with your own hands without a bearing: the best workshops Homemade spinner for hands

Spinner is a new fun toy that appeals to adults and children. It appeared in America last year and for a short time gained immense popularity. The principle of the toy is simple: with the middle and thumb of one hand, we take the central bearing. With the other hand we activate the wings of the turntable. With enough good management skills, you can bring the toy into action with one hand. Take index bearing with thumb and thumb. The spinner consists of three parts: the housing, the bearing and the cap.

Spinner benefits

1. Hand motility develops, fingers become more sensitive. This tool is very useful for those who have suffered various injuries of hands.
2. This toy is a kind of anti-stress, which soothe the nerves. In addition, thanks to her, you can concentrate, restore performance, relieve anxiety and nervousness, and also become less irritable.
3. Spinner will be an excellent companion during a long trip, it can perfectly take your free time.

LED spinner on controller

Someone buys them, and someone makes their own hands. Here is a circuit diagram of a spinner with microcontroller-controlled LEDs. When rotating, all sorts of pictures and signs are created.

List of project details:

• MK ATtiny-45
• 5 smd led (1206)
• 5 smd resistor (47 Ohm)
• 1 16 mm battery (3 V)
• Dia 22mm bearing
• A piece of wood or plastic

As you can see, the scheme is the simplest, but if someone doesn’t understand something, study the datasheet from Atmel.

Positive conclusions LED go to PB0 - PB4 on the MK. For current limiting resistors are added between them. Negative contacts of LEDs go to minus - GND.

There are various options for displaying figures, so that the browser page is created to create sequences of images for the spinner. In the general file, the link to which was higher, you will find a drawing, firmware and program.

Ball bearing spinner

This spinner consists of a housing on bearings and a plug. The central bearing is the most important. Speed \u200b\u200band time of rotation of a spiner depend on its quality. Plugs are inserted into the center hole.

One of the most accessible tools is paper and cardboard. Handmade spinner is made of paper using a knife, four bearings, and glue. First you need to make drawings. Using a clerical knife, cut out parts from paper or cardboard. Bearing holes are cut with nail scissors or a knife. It is important to see that their diameter should be slightly smaller than the diameter of the bearing. This is necessary so that the bearings fit tightly into the holes. The number of parts depends on the width of the bearing. For bonding you need a lot of glue. He will give the product greater strength. After finishing work, we paint the toy in any color.

To increase the moment of inertia, it is necessary to provide weights. The simplest option are the coins glued to each other. For 10 mm plywood, you need to glue together 8 ten-kopeck coins. The inner surface of the workpiece is aligned with the help of the drill. External surfaces gently and quickly bring to the contour grinder with a grinding wheel. All the remaining irregularities manually remove the sandpaper.

Those who can work with a jigsaw and drill can make a spinner from wood. The tree is an ecologically clean material. The product turns out beautiful, pleasant to the touch. First choose solid wood. For beginners it is better to use plywood. To work with wood, you need skills. First prepare the drawing. You can think of it yourself or just print from the Internet. Attach the paper blank to the tree or plywood and cut around with a pencil. To cut and grind the part with sandpaper. The hole can be cut, but it is better to make a drill so that the hole is smooth. The important point: to make a drill on one side of the hole to half, and then turn the part. So more likely to get the perfect hole for the bearing. The thickness of the wood or plywood should be exactly the same as the bearing. If it is a little more, you need to polish it.

Usually use the bearing of the wheels of a skateboard, rollers or scooter. They have a standard size diameter of 22 millimeters, width and internal diameter can be chosen at their discretion.

Having experimented with the sizes, we came to the conclusion that the ideal size for long torsion is 25-27 mm in diameter. At the same time for the spinner is better not to take bearings less than 20 and more than 30 mm.

Finger spinner will be the savior of those people who, during stress, gnaw nails, pens or the like. The pinwheel is designed to relieve stress, warm up fingers, as well as to concentrate attention and develop hand motility. Such a device will become an indispensable thing for children and adults.

The surface of the materials can be bumpy or smooth, the color can be found a variety of options: white, black, red and many others. The size of the toy is small, which allows you to carry it with you. Unusual and stylish design can make it a great accessory.

How to make a spinner with your own hands

Why do you need a spinner from the store, if you can make it mono yourself. The whole process of work will take a little time, and by design it is simple. In order to start tinkering, you will need:

• Textolite;
• screed for furniture;
• bearings;
• drill and drill to her;
• ruler, compass.

First you need to take a PCB and cut out the basis for the spinner. Previously, with the help of compasses, a drawing of a toy is drawn, and only then it is cut out. Before you draw the basics, you need to know the size of the bearing, for example, it is 22 mm, respectively, the compass should be inserted into the textolite by 11 mm and draw a circle. After that, insert the compass to 18 mm, and draw another circle. An individual count is required for each case. Make it simple, all the variety of options presented on the Internet, there are stencils for spinner.

Then proceed to work with the bearings. Each of them must be rubbed with resin, after which you can combine them with a bar. Only after that you can drill holes for the liner. For this you need to note six sectors of the spiner. Each point of intersection of sectors and circles is the center of the sleeves. It is necessary to drill holes in each intersection, exactly six pieces. Then you need to drill out the center of the spinner.

Each sleeve, before you insert into the hole, you need to polish. Make it very simple, for this it needs to be inserted into the drill chuck and at the lowest revolutions rub on the sandpaper until all the paint from them is removed. Each of the sleeves must be lubricated with the same resin and pressed.

After all actions are done, the toy needs dates to dry. This will take at least six hours, after which you can enjoy playing with a spinner for hands.

Video - the funniest spiners

This craft will be dedicated to how to make a spinner with your own hands. The design is quite simple, so much so that even a child can make it.

What is a spinner? It is an anti-stress toy that develops hand motor skills in children and calms the nerves of adults. That's what you need a spinner for hands. The basis of the spinner is a bearing or a rotating core, and weights are located on the edges. Thanks to this design, the entire body can rotate around its center for a long time, and with your fingers it is possible to accelerate it.

How to make a spinner

A key role in the creation of this toy is the ball bearing. But the materials of which the body will be made, is not so important. It can be wood, plastic, paper, cardboard or metal.

How to make a spinner at home

By the way spinner can be done without any body at all. Let's consider this option, as a first example, we will make a spinner with our own hands at home from 4 bearings and clamps.

All the necessary materials, except bearings, most likely already have you at home. But the bearing can be removed from the old rollers or buy in a sports store. As balancing weights we will use exactly the same bearings. We will connect them with clamps.

We will need:

• 4 bearings
• 9 screeds

Connect the 3 couplers between each other and place the bearings in the corners of the resulting triangle. Make 3 more rings, put them on the design, place another bearing in the center and shade everything tightly. Cut the sticking stitches and everything, now you know how to make a spinner yourself.

   But do not forget to pre-clean the bearings from oil and dirt. After which it can be painted in your favorite color.

A simple way to make a spinner at home

In this method, we will connect the bearings using epoxy resin and colored laces. If you already know how to make a spinner from a bearing, then you will have no difficulty.

What can be done spinner:

• 4 bearings
• epoxy resin
• sandpaper
• colored shoelaces
• markers

First open one bearing and remove grease. Using sandpaper, sand the part of the metal that you want to glue together. Prepare the epoxy and apply it on the ends. Add some resin on top and let dry.

In order to decorate your spinner, you can use multi-colored laces.

Apply some glue or epoxy to the lace and glue on the anti-stress toy.

With the help of markers you can decorate the spinner in any color you like.

How to make a spinner from one bearing

It is not necessary to use 4 bearings, this is done for aesthetic beauty. The main rule when creating a hand twister is the weights symmetrically located on the edges.

As weights, you can use conventional bolts or nuts. The washer is used as a stand in order not to accidentally glue the construction to the table.

Draw a circle and draw three diagonal lines. Place the bearing in the center of the circle, and glue the bolts to its three sides using superglue or epoxy resin.

Now you know how to make a spinner with your own hands out of the bearing and bolts. By the way, this design turned out to be the most successful, thanks to the long bolts the spinner turns for a very long time.

As you can see everything is very simple and there is no need to immediately run to the store for a new toy. Now you know 3 easy ways to make a spinner in 5 minutes.

How to make a paper spinner

Principle you understand. So now you can safely make this funny toy out of anything. We will use cardboard or paper as a case, and ordinary ruble coins will be weights.

How to make a spinner from paper without bearing

In this example, we do not need a bearing. It can be replaced by an ear stick or wooden skewer, around which the finger spinner will rotate.

It will take:

• Cardboard
• Paper
• Coins 6pcs.
• Glue gun
• PVA glue (you can only do with a glue gun or super glue)

The detailed process is shown in the video.

As you can see, a new-fashioned spinner toy can be made from almost anything. Share in the comments what ways you know!

Spinners entered mass fashion not so long ago, but in just a few months not only adults but also children won the hearts. Today spinners are spinning everywhere: on the street, at work, on the subway and even in kindergarten! And every child wants his toy something different from those that already have peers. You can buy an original spinner, but such a toy is not cheap, and the search for a unique spinner takes a lot of time. The best solution is to make a spinner yourself.

So, we bring to your attention a few simple ways how to make a spinner with your own hands from the materials that each house has.

1. How to make a spinner from plastic covers?

Materials:  caps from any plastic bottles of the same size (4 pieces), clay, hot melt glue, nail, scissors, lighter and toothpick.

What do we have to do: Put the clay in 3 lids, using the hot melt glue the remaining space of the lids. Take the fourth lid (without clay) and make a hole in it, for example, a heated nail. Glue the lids with sand to the one where you just made the hole. Take the glue stick and cut 2 small pieces (1 cm) from it. Break a toothpick in half and put a piece of glue on one end of it (make sure that the sharp tip of the toothpick does not stick out) and place it in the center of your future spinner. On the back of the tip of the toothpick, put on the remaining piece of glue stick. Your spinner is ready!

For a more interesting look, you can paint the caps in different colors with acrylic paints.

2. How to make a spinner from cardboard?

Materials:  caps from plastic bottles, cardboard, scissors, a marker, an awl or nail scissors, glue, 3 coins and a rod from a pen.

What do we have to do:  Using the caps, draw 4 circles on the cardboard in the shape of your future spinner. After that, cut out 5 such blanks and glue them together, carefully gluing the edges. Next, cut out smaller circles. With the help of awls or thin nail scissors, make a hole in the center of the spinner. On the sides of the blanks, glue 3 coins or any stickers.

Next, take the pending handle stem and carefully cut 1 cm from it. Make small holes in the center on two small circles. Insert the cut piece from the stem of the handle into one of the circles and glue it along the edges of the hole to fix it securely. Push this circle into the center of your spinner and glue the second circle on the reverse side. The two remaining small circles can be glued over the tips of the rod. To make your spinner spin faster, put some kind of gasket between the workpiece of the spinner itself and small circles (in our example, we used metal pendants).

Is done! Let the child decorate his spinner as he wants, you can use glitter, stickers, rhinestones and other decorations.

3. How to make a spinner using bearings?

Materials:  bearings (3 pcs), tie clips, glue gun or superglue (for a more complex spinner).

What do we have to do:  tie with cable ties bearings from all sides. Cut off the extra hose clamps and that's it - the spinner is ready!

To make it more bright and attractive, you can make the design more complex. Take 7 bearings, place 6 of them around the seventh. You will not use all 7 bearings, you only need 3 circular and 1 central. The rest of the bearings you need only for accurate measurement, so we will leave only those that form a triangle. Glue all the necessary parts with a glue gun or superglue. Spinner is ready! Decorate spinner as you like. You can glue fluffy wire, apply glue to the sides of the spinner and cover the edges with sparkles.

Be sure that nobody will have spinners like your child!

How to make a spinner with your own hands at home? - very many people are interested in this issue. And no wonder, today there is a real boom with spinners. Everyone already knows about them, and everyone wants to twist it. But the prices of normal spinners are puzzled by the fact that a piece of material and bearings are not worth so much. There is always a way out - make a spinner with your own hands.

Honestly, at first I generally thought that the spinner is some kind of spinning toy for cats, and only recently became interested in what it is and how to make the spinner myself.

The choice fell on the classic three-spinner model, which has a bearing both in the center and on each petal. Bearings on the edges are needed more as weighting, twisting, holding them is not so interesting, and depending on the size of the spinner, not all have enough finger length.

Spinner bearing

So, to make a quality spinner with your own hands, you first need to get bearings. Cheap spinners are most often manufactured without bearings, which is somehow not ice. It is possible to cut out the cardboard and twist it on the handle stick, but we want everything to be Feng Shui).

Most often used bearing designated as 608. This is not some magic number, but simply the bearing brand, there are 607 (less) and 609 (more). The 608th bearing has an outer diameter of 22 mm, and the inner one - 7 mm. Thickness is 8 mm.

It is used most often at the anchor of motors perforators and electric drills. Well, I was found in one of the auto shops. In the same place, by the way, at me and repaired the perforator.

Each bearing was packed in a bag and a small box, claiming that it was made in Russia. But as it turned out from a friend of the seller, the inscription "Made in Russia", as a rule, says that he is Chinese ... (Clarification - I live in Tashkent, Uzbekistan, so I don’t know how things are in Russia)

A high-quality bearing is a very important element of a spinner. depends on it how long the spinner will spin, and how stable it will be. Therefore, later the bearings were replaced with similar Korean ones.

Good bearings, but smaller (15 mm in diameter and 5 mm thick) were used in old hard drives. The rotational speed of the hard drives of the old generation was 5400 rpm, and the modern 7200 rpm. In modern hard drive bearing is in the motor and has an even smaller size. On such a bearing you can make a good high-speed spinner, which can spin for a very long time.

Cooking bearings for spinner

Bearings are sold closed dust rings and lubricated. For a spinner, no lubrication is required, it will only get your hands dirty and slow down the rotation with its viscosity. Therefore, the grease must be removed. This will require 50-100ml of gasoline.

We disfigure the bearings, removing dust rings from them with something sharp and thin. Throw the bearings in a jar and pour gasoline. We leave them in gasoline for a few minutes, then we chat in a jar so that the bearings can boil over. Dipping an unnecessary toothbrush into gasoline, we remove the remaining grease from the bearings.

To get rid of the smell of gas, you can wash the bearings with soap using the same toothbrush. If you prefer, you can put the dust rings back in, but I prefer the combination of wood and metal. Now the bearings are fully ready for use in the spinner.

Spinner material

As the material was chosen plywood, as the most convenient during processing. It is also possible to cut out from thick sheet getinaks or plexiglas, but it is easily scratched, so it is difficult to make it neatly. A 10 mm piece of plywood was found in the bins of the house, from some killed Soviet tape recorder.

I did the markup using a compass, a ruler, a protractor and a pencil. It is important to make very accurate markup, otherwise the center of mass can then shift and the spinner will spin as it rotates. It is more convenient to print a pattern from paper, cut and circle, it will save time and nerves.

Spinner case fabrication

Because the classic, curved shape was chosen, then a 19mm crown was used to cut the inner roundness and holes for the bearings. It is better, of course, to use 20 or 21 mm, but I simply could not find it on sale.

The crown has a special holder into which the centering drill is inserted. Before drilling large holes, it is better to drill guides of a smaller diameter in the centers of future holes, and then, fixing the crown in the drill, drill 6 large holes in a circle and one central hole.

Crowns on wood have quite large teeth. They can easily peel the top layers of plywood. Therefore, if you decide to make a spinner with your own hands from plywood, then it is better to drill out to the middle, first on one side and then on the other.

Cutting off the spinner body

Now saw off excess, each petal. For this, a jigsaw was used, but it is also possible with a regular hacksaw. We try to cut as close as possible to the markup so that later we have to grind less.

We ratchet holes for bearings

In addition to the outer part of the case, the internal part needs to be improved. holes for bearings. They turned out 3 mm less than required. Using a round file and focusing on the markup, we bore the holes so that each bearing comes in very tightly. Of course, it’s better to do all this boring with a machine, if you have one.

Customize spinner thickness and skins

After everything was squandered and grinded, it was time to bring the found plywood to the thickness of the bearings, i.e. 8 mm instead of 10. For this, on each side of the workpiece, it was removed by a layer of plywood and it became exactly 8 mm thick. Further, the entire workpiece was otkkuren first large, and then fine sandpaper.

Finished design:

Finger holder

After inserting the bearings and twisting, it was decided to make a holder for the fingers. When drilling holes, there were holes in the holes that were full of holes that went to this business.

With a sharp knife, a column was cut out of the rack, according to the internal diameter of the bearing. Kruglyashki were trimmed in layers to 3. The ends of the column were filed with a file so that the rounds were tightly dressed. Here are the components of the holder:

It remains only to insert the holder into the central bearing, pre-filling the joints with glue and waiting for complete drying to enjoy the new toy - spinner, made with your own hands)

Now you know how to make a spinner with your own hands - a rather useless thing, but cool.

All questions write in the comments

Has your child succumbed to the mass fashion of spinner spinning? Asks himself red, yellow, and still glowing and in the form of a minion? In general, so as not to all? Then you can make a toy with your own hands. Moreover, such a lesson in labor will take you and your baby. And if you still do not know what a spinner is, there we answered all the popular questions about this modern, extremely modern fun.

We have collected for you three ways to make a spinner, two easy and one - more difficult (here you need the help of the Pope). But we are sure that the tools and materials should be found at home or in the country. Each instruction is supported by a video tutorial found on YouTube for clarity. So, how to make a spinner out of paper, plastic caps and wood?

Method 1. Spinner made of paper and cardboard.

Simple, cheap and not at all angry - paper spinner for beginner spinner-makers. An older child will cope on his own, the baby may need some help, and the result can be proudly taken to the garden or school - there creativity is always held in high esteem.

What you will need:

• Cardboard, marker and caps (or ready-made template from the Internet)
• Scissors
• Nail scissors or awl
• 3 coins
• Handle bar
• Paint or glitter for decoration

Instruction:

1. Download ready spinner template from the Internet. Or draw it yourself by enclosing a plastic bottle cap on cardboard. You need to cut two pieces of cardboard in the form of a spinner.
2. Cut four more smaller circles. You can circle a coin of lesser value.
3. Stick on the sides of one of the cardboard blanks three coins of a suitable size.
4. Glue the other half on top of the blank with coins.
5. Make a hole in the center of the spinner with manicure scissors or an awl.
6. Cut about 1 centimeter from the rod from the handle.
7. In two small circles, make holes in the center.
8. You can paint the finished preparation of the spiner in any color or decorate it with sparkles, rhinestones or stickers with your favorite child characters. Everything is your choice and completely unique!
9. Insert a piece of rod into one of the small circles and glue it along the edges of the hole.
10. Slide the circle with the rod into the center of the spinner and glue the second circle on the other side.
11. Glue the remaining two small circles over the ends of the rod. Done! A spinner made of cardboard, without a bearing and with a full expansion of fantasy in terms of design will surely take the child for a while.

A source: PLASTILIN

Method 2. Spinner plastic caps.

This spinner will require a little more material and diligence, but it will last an order of magnitude longer. In general, a spinner made of Coca-Cola lids is about the same as crafts from matchboxes for older generations. Lovely heart consumables and warming the soul with the minimum for actively functioning (that is spinning) gizmos.

What you will need:

• Plastic bottle caps
• Kinetic sand or plasticine
• Glue gun
• Nail and lighter
• Glue stick
• Scissors
• Toothpick

Instruction:

1. In the three bottle caps, put kinetic sand or clay almost to the top. The main thing - to weight the blades.
2. Use a glue gun to fill the remaining space in the caps to the top.
3. In the fourth (without sand) cover, make a hole (you can use a heated nail).
4. Glue the three covers with sand to the center cover with a hole.
5. Cut two pieces of about 1 centimeter from the glue stick.
6. Break a toothpick in half. Put a piece of rod on one end (the toothpick should not stick out) and slide it into the center of the spinner.
7. Put the second piece of rod on the tip of the toothpick on the other side. Done! If there is a great zeal, such a spinner can also be creatively decorated - painted with paints (for example, acrylic) or pasted over with something positive. And you can leave it as it is, by choosing interesting combinations of lids from under bottled beverages.

A source: Chip of the Day

Method 3. Spinner made of wood (with bearing)

We turn to the most time-consuming method of manufacturing spinner. It is impossible to do without parents here, but the result can be easily laid out on the desk together with purchased toys. Again, in terms of design, there is freedom for expression. For those dads and children that are friends with a jigsaw, they know how to find bearings on the shelves of hardware stores and know which side to hold the drill.

What you will need:

• 2 mm bearing
• Plywood Sheet (5mm)
• Stack of coins
• Scissors
• Pencil
• Hand Jigsaw
• Sandpaper
• Template (or cardboard and marker to create it)
• Clamp
• Drill

Instruction:

1. Glue the template on a sheet of plywood and mark places for future holes in each of the circles.
2. Drill holes in each of the three circles on the sides, so that it is easier to cut them later.
3. Thread the jigsaw through the holes and cut them out.
4. Saw the blank itself out of a sheet of plywood and sand it with sandpaper.
5. You can paint the spinner in any color you like.
6. Thread the bearing into the center circle, if it does not fit well, you can hammer it in there with a hammer.
7. Glue a stack of coins for the inner circles. Start with a five-ruble coin (put it under the circle), then a two-ruble coin and a five-ruble coin on top again.
8. Do this for all circles. You can decorate it on top as desired. Done! Just think how much benefit from homemade anti-stress toys: we had a good time together with the child, we did a nice job and saved on the purchase of another plastic trinket. And it turns great!