What to hang a swing in the country. How to make a swing out of wood and metal

Good afternoon. Today we will make a swing for a summer cottage. I decided immediately IN ONE ARTICLE to collect all the variety of swings for giving (from simple to complex). So that you can choose the swing model that you like best.

I will NOT ONLY show ideas - we will also LET'S LOOK AT EACH MODEL IN DETAILS…

And more - I'll tell you HOW to attach the swing to the support beam - all 4 ways.

I will start from the SIMPLE ideas of a swing for a summer residence - to ideas MORE COMPLEX AND MORE INTERESTING.

And the most original ideas swing for children- with slides, rope climbing frames and built-in wigwams - I put it in a separate article

So let's get started...

SIMPLE idea - how to make a swing from a pallet.

If you have a cargo wooden pallet (pallet) left on your site (after bringing in bricks or other building material), then it can be used as the basis for a country swing.

We need a wooden pallet (pallet) - a strong rope - and something to which we will hang. Or it will be a tree trunk. Or you can make support on two strong pillars. We then - a little later in the same article- we will consider swing support options (And then I will dwell on this in more detail).

But… if you develop this idea of ​​a swing from a wooden pallet further… then you can make everything much more comfortable… Like this…

And if you don’t have one - but as many as 2 pallets were found in the household ... then from two pallets-pallets you can make a cozy swing with a back ... paint ... put sofa foam cushions ... And voila 2 shabby pallets - turned into a luxurious swing for a summer residence .

Of course, the pallets must first be cleaned, sanded with sandpaper (so that there is no splinter) and painted (stain or paint) and even varnished (but preferably moisture resistant).

How to fix such a swing - I will tell at the very end of the article ...

Rocking chairs - THE SIMPLE IDEA of swings for summer cottages.

This is what these country swings look like.

Pay attention - NOT JUST boards with a hole for a rope - but harnesses, which are duplicated at the bottom with two more planks. So that the rope fastening is held tighter and there is no strong friction on the rope when swinging.

I think there is no need to explain for a long time how to make such a swing yourself.

ANOTHER MODEL - a swing with a rope for summer cottages.

And here is also shown HOW you can fix the rope on the swing. That is, the essence is very simple:

We make 4 saws (we cut out the grooves) - 2 grooves at the end of the board - and 2 grooves along the edges closer to the corners of the board. (it is not necessary to make the edge of the board as semicircular as in the photo - the same principle will work on a rectangular cut of the board).

And then when 4 grooves are cut out - we place the rope - in them - in such a way as shown in the photo.

Though grooves remain open- the rope does not jump out of them. Under the force of tension, it only fits more tightly to the grooves - and a completely reliable fastening of the rope to the swing seat is ensured.

Swing for a summer residence - from a snowboard.

Or here's another idea for a summer residence ... Snow boards are made of very durable materials. Such a board, although it looks thin, is actually very wear-resistant (it is extremely difficult to break it). And therefore it can also be used as a swing seat in the country.

Swing for a summer residence - with your own hands from two logs.

And here is another variation of the swing seat - from two logs.

Here in the photo above you can see how easy it is to make this swing from two segments of rounded beams. A very simple model. We wrap two pieces of rounded logs with a rope and fasten them with some kind of cunning marine knot.

Swing from the board - with a roll in the longitudinal direction.

But the swing model - when the roll (motion vector) is directed in the longitudinal direction. Such a rocking chair can be made more authentic - to swing on it in a friendly neighborhood-children's campaign.

AND LET'S COMPLISE THE TASK ... now there will be a more serious swing ...

Country swing - from the rounded beams.

How do you like this cozy summer cottage?

Nice, right?

Let's take a closer look at how to make such a swing ourselves.

SUPPORT - two A-shaped structures from rounded bars - (two letters A are assembled from bars - as we see in the photo) - we put them on legs and we put a cross beam on them.

And in order for this beam to lie more reliably on our A-shaped racks, we also (see there from behind) strengthen it with additional short beams.

ROCKING CHAIR ... here is an interesting rocking chair.

seat- L-shaped bench made of bars and battens with planks + armrests made of bars.

Seat holder - also cool - it's not a chain or a rope.

This is the same rounded beam - which is tightly attached to the seat with its lower end (in zone of her lower seat bar And in the armrest area).

And the upper end of the holder-beam has a movable fastening in the form of a metal ring. And this ring is fastened with fastening carabiner the suspension support itself.

Detail drawing exactly THESE swings from a bar- (with dimensions and large photographs from all sides) - I posted it in a separate article ... In this article, you will find everything on a bench-type swing.

And here is almost the SAME MODEL of the support post - but in a slightly different variation. And then there's an elegant crate added to the side of the supporting spreaders.

Swing for a summer residence - we make it from a non-rounded timber.

Here is a model..

It can be made with a seat-bench.

With two seat-boards - you get a swing into two separate places.

Moreover, note that we hang them to the same anchors on which the swing-bench hung before. Thus, different rocking chairs can be hung to the same swing support.

Or here is another combination to the same swing support. Combined swing with seat-chair and seat-board.

Fasteners are standard for swings - chains and carabiners made of metal rings and hooks.

This is how two chains from the back and seat of the chair look like - they meet in one ring and then they go to the carabiner for fastening the beam.

And like this - a fastening anchor with a carabiner for attaching a rope (or chain)

But I'm getting ahead of myself...

In more detail (below in the same article) I will show 6 ways to attach the swing to the support beam... there we will dwell on carbines in more detail ...

In the meantime, we continue to look at what other models are available ..

Almost the same model - but with a continuation under another swing.

Here is a variation of this model- where the transverse beam extends beyond the side boundaries of the support beams and a light rocking board is suspended from it.

Swing wooden with a canopy.

But the swing model is complemented by a canopy roof - in case of a rainy summer in the country.

And pay attention - there is already a ROPE HOLDER - another system of carabiners.

Here are such A-shaped swings (with supports in the form of beeches A) we will step by step make in a separate article "Swing for a summer residence - STEP by STEP we do it ourselves."

Everything will be simple and clear there - in such pictures.

Also, you might have a question...

And what to do - if I want to build a swing,

but I have no bars - only boards?

Here is the answer - a double board calmly replaces a beam in terms of endurance and load.

Well, now let's talk about how to attach the swing to the support.

HOW TO FIX THE SWING - TO THE SUPPORT BAR.

(6 WAYS)

Swing attachment - carabiner (with beam girth)

Here we see photos of mounting systems for swings - which are mounted either on a rectangular beam (square girth of the carabiner) - or on a rounded beam (round girth of the carabiner).

Through fastening - carabiner (with drilling of a bar)

Or special anchor devices for through fastening on a bar. Most of the swings from our photos in the article are precisely on these anchors that are attached.

You can make a garden swing for a summer holiday in the country with your own hands, you just need to choose a drawing . You can make a swing from different materials, choose a model to your liking.

A swing with a bench, designed for 2-3 people, is a typical model for garden plots.

Previous

Track.

Basic structural elements.

Dimensions are calculated based on the model.

There are 2 types of connection parts. Preferably welded, since screw fasteners unwind under the effect of vibration during swinging. It is necessary to periodically tighten the bolts and nuts.

There are two types of connections of structural elements: welded and prefabricated

A hole is drilled in the crossbar, a bolt is inserted into it, to which the eye-nut is attached. With the help of a connecting ring, a bench is suspended. The connection is periodically lubricated to avoid damage to the mechanism, creaking.

The bench is suspended from the crossbar on rope ropes, chains, metal cables

The construction of an iron swing begins with the installation of a frame. For portable structures, it is more correct to make a connecting frame from a metal profile along the lower perimeter of the frame. Stationary - dug into the ground to a depth of 50–60 cm, then concreted.

All metal structural elements are treated with rust-preventing compounds and painted.

U-shaped swing

They are structurally simpler and consist of side posts and a crossbar. Stability is provided by the upper corner strips connecting the supports.

The U-shaped structure is less stable, therefore, such a swing is buried in the ground, followed by concreting

When drawing up a plan, a model scheme, you need to take into account some points. The seats are suspended at a height of 50–60 cm. A minimum indent of 30 cm is made from the side supports.

DIY garden swing made of wood

Naturally fit into the concept of landscape design. On the farm, you can always find material for harvesting wood: timber, logs, boards. Simplicity of processing, plasticity of a tree - one more advantage. Unlike metal, it does not heat up so much in the sun.

The durability of the structures is given by the treatment with means that prevent the penetration of moisture into the material, varnishes that form a film on the surface.

It is also possible to assemble a swing made of wood and metal

The frame is made in the same shape as for metal structures. To build a swing, choose a model, make its scheme. Before drawing, decide what type of tree will be used.

The layout of the material on a 3-seater swing.

Measurements are made with a meter, the evenness of the structure is checked by a level, a building corner. Details are cut with a saw, electric jigsaw. Grind with sandpaper, grinder with a special nozzle. A screwdriver is used to screw in self-tapping screws, holes in a tree are made with a drill with drills of different diameters.

Holidays with children can be made even more enjoyable by providing interesting elements and facilities.

This is a barbecue area, and a playground or a whole complex.

In this article, we will consider the manufacture and assembly of wooden swings for summer cottages, drawings and photos of various construction options.

Blueprints

There are a lot of advantages in self-manufacturing of the structure:

• the choice of design convenient and functional according to your own taste and desire;
• a product made of natural wood is environmentally friendly and durable (with appropriate processing);
• cost savings (buying a finished product is always higher, moreover, there is not always a guarantee of quality);
• the tree will harmoniously fit into the environment, and the canopy over the structure will allow you to enjoy measured swaying and fresh air without the risk of getting burned under the scorching fire.

Did you know?In Ecuador, in the city of Baños, there is a swing on which brave tourists can soar over a precipice more than 2000 m deep and admire the view of the Tungurahua volcano.

We adjust the board to the desired dimensions, place them on a straight surface (on the floor) in the position in which they will be assembled, measure the width of the base and the angle at the top of the future rack.
In the upper part, two racks will be fastened together by a transverse beam. Therefore, the angle is measured, taking into account this detail, the easiest way to take measurements is to cut off excess wood by attaching a short bar of the same width to the parts of the supports folded together, draw a marking line with a pencil.
Cut off excess parts with a jigsaw, assemble all the parts together. Fix with a clamp for complete immobility and make sure that the bottom of the rack is not skewed, a level will come in handy here, remove excess.
Make the second rack in the same way.

A board of the desired size can be made rounded at the edges protruding from the fastener for aesthetics.

Next, we assemble the support: before screwing in bolts or screws, make sure that all corners of the structure correspond to the calculations.
The rack is not ready yet: it will need additional side rails for reliability. We try on a beam of suitable length to the bottom of the rack, the distance from the floor corresponds to the level of the future hanging bench.
Mark the cut lines with a pencil, making sure that there is no skew with a level. Install the prepared cross member in the right place, fix it with a clamp and fasten it with bolts.
In the same way, fabricate and install the crossbars in the upper corner of the rack about 20 cm below the attachment point. We add fasteners in the upper part for final fixation - the base of the swing is ready.

Important! Remember, all fasteners must be galvanized: this will protect the wood from cracks and extend the life of the wooden product.

Bench

Let's go to the bench. In order not to miss anything when making a swing to the country house with your own hands, refer to the diagrams and drawings.
Make frame parts for the bench of the desired size, turn and sand them, mark and carve grooves in the right places. Don't forget about armrests, they can be made curly.
Then the frame must be assembled and fixed with a clamp (one tool is indispensable here) in order to more accurately calculate the width and length of the back and seat parts. Start making details of a bench for a wooden swing, it is not difficult to make them with your own hands, the main thing is to take measurements accurately.

Two long parts with a groove turned along (for lamellas) and spikes at the ends. A thin planochka, narrowed on one side (under the width of the groove) and equal in width to two bases, will be needed during assembly to close the groove between the lamellas. Cut the plank into pieces equal to the width of the gap between the lamellae.
Further make lamellas, depending on the length of your bench, there will be from 10 to 12 pieces on the back, located perpendicular to the bases, do not forget to carve spikes at both ends for the grooves made in the bases.
For the seat, make the slats longer by the length of the bench, they will be parallel to the longer bases of the seat. The number of slats also corresponds to the width of the seat.
All parts are ready, start assembling the bench.

Assemble the backrest: install one of the bases with the groove up, mark the location of the lamellas with a pencil. Lubricate the groove and install all the slats in turn, and then the chops that close the gaps between them.
Also fix the upper base with glue and fix the assembled back with clamps.
Next, assemble by smearing all the grooves with glue, and fasten the frame for the bench with bolts. Install the prepared back on the frame, coat the spikes included in the grooves of the two side frame guides with glue.
Grind, sand, fix the seat slats with glue and press with a clamp.
Do-it-yourself wooden swing is almost ready, it remains to install the suspension and canopy.

By appointment, a garden swing is akin to a bench - outdoor recreation in the shade of trees or a canopy. The design differences are only in the “fulcrum” - the seat of the bench stands on legs, and the swing is suspended on a beam. Based on this, we will consider different options for wooden swings made by ourselves.

Simple solutions: board and rope

The easiest option is two ropes and a small piece of board for one person. Since the load is relatively small, such a swing can be hung even on a strong branch of a large tree. The main thing is that the rope is thick enough, and the locking knot is securely tied.

The disadvantage of the first option is the unstable horizontal position of the seat. Two points of support are not enough for him, even if the rope is thick and the knot is large - one awkward movement and you can tip over. Therefore, it is better when the seat is suspended from each corner of the board. The ropes can already be chosen thinner, and so that the knot does not come loose, wrap it on both sides with construction tape.

Simple solutions: improvised materials

There is such a separate direction for garden (and even home) furniture - the use of pallets. Of course, we are not talking about semi-handicraft pallets from poorly processed wane boards. In order to minimize surface finishing, it is necessary to choose a euro pallet (there are two stamps on the bosses: EPAL and EUR). Making a swing is easy - sand the top boards and side structural elements, coat with a primer, apply varnish or paint in two layers, hang on ropes.

And so you can use an old wooden semi-chair.

For those who are not constrained by means and love comfort, we can advise you to saw off the legs of a wicker chair and hang it on the ropes in the garden.

swing sofas

Swing sofas have a more complex design, consisting of a seat, back and armrests. But there are also different ways to do it.

For simple models, it is enough to know the basic techniques of carpentry.

Swings with a more complex design require the skill of a carpenter.

Such sofas are hung on ropes or chains.

The capacity of these swings is designed for two or three, and in a rare garden there is a tree whose branch can withstand such a load. Therefore, in order to hang them, you need a beam with its own supporting structure.

Stationary swing supports

The simplest swing support is two pillars dug into the ground, with a crossbar on top. And in order for the pillars to stand reliably, their underground part must be concreted.

This design can be complicated by making a canopy or lattice over it like a pergola.

There are combined supports, when one end of the crossbar is attached to a tree, and the other - to a triangular rack.

But it is the stationarity of the supports that is often considered a disadvantage of the swing. For example, they are not easy to move to another place when the site layout is changed.

Portable swing

Portable structures have two racks in the form of an angle with an additional stiffener fixed in the middle or at the bottom of the supports. The choice of this form is explained simply - the triangle is considered the simplest rigid figure.

The material for the manufacture of racks can be timber:

round log:

sanded dry "wild" logs and poles from your own garden or a nearby plantation.

roof swing

The swing rest area in the open area can be protected from the sun. The simplest option is an awning in the form of a pitched roof. And if you choose a waterproof fabric for the awning, it will also protect from rain.

A gable roof made of lightweight roofing materials - corrugated polycarbonate - protects even better from precipitation:

or soft tiles.

In the second case, for a small angle of inclination, you can not even make a skate.

And next to the house (or dacha) in a rustic style, you can put a swing covered with the traditional roofing material of a Russian hut - dry reeds or straw. And so that it is not thick and does not leak at the same time, rolled waterproofing is laid on a continuous crate.

What do children do in their free time on the street? Run and play, build a house out of sand, ride a bike, kick a ball. And many kids enjoy spending time on the swings. They are very fond of rising and falling sharply. Such a swing can be made with your own hands, using improvised material for this.

• 1 Types of children's swing
• 2 Preparatory work
• 3 Step-by-step instructions for making a hanging swing with a chain and a wooden seat

• 4 How to make a do-it-yourself swing-balancer for a child from wood
• 5 Video: how to make a tire product
• 6 Decoration process

Types of children's swing

The swing performs a number of useful functions:

Help to brighten up the leisure of children.

Contribute to the training of the vestibular apparatus.

Develop coordination of movements.

Children love swings

Improve mood due to the release of adrenaline during high rises and sharp falls.

Monotonous swaying has a beneficial effect on the nervous system (soothes, relieves stress).

For several centuries, swings have remained a popular attraction, not only for children, but also for adults. Not a single folk festival in Ancient Russia was complete without “flights” on these devices. During the Russian Empire, they were both among the poor and the rich. Naturally, they looked different: the poor swung on ordinary wooden boards tied to poles with ropes, while the swings of the rich were decorated with decorative elements, pillows, bows and ruffles. In our time, interest in them does not fade away, they can also be seen on courtyard grounds, in many children's organizations, in country "residences".

What material is suitable for the manufacture of yard swings

You can make a swing with your own hands, using almost everything that is at hand for this.

Table: advantages and disadvantages of different materials

Material type	Advantages	disadvantages
Wood	Strength. Environmental Safety. Long service life. Non-slip seats. No dependence of their surface temperature on weather conditions.	Susceptibility to decay if not properly treated. Increased risk of splinters and minor injuries.
Metal	High reliability. Such swings are able to withstand significant loads (up to 150 kg). The possibility of decorating with different details.	Susceptibility to corrosion. The high thermal conductivity of the metal, which interferes with the comfortable use of the swing (in the heat they are very hot, and in the cold too cold).
Plastic	Extensive range of shapes and colors. Ease of installation (due to the low weight of the structures). No need for special care. Harmony of presence both on suburban areas and in massive complexes for children's entertainment.	Low reliability of the design compared to products made from other materials. Cannot be used outdoors. Susceptibility to the influence of severe frosts, temperature extremes, high humidity. Can only be used by younger children. Not all plastic structures withstand severe frosts, temperature extremes and high humidity.

Photo gallery: types of swing by material

Wooden swings require careful antiseptic treatment and surface grinding

The strength and reliability of metal structures no one disputes

Plastic children's designs can be purchased ready-made, but they are only suitable for babies.

Use of non-standard materials

Some craftsmen can make swings from other materials, using car tires, plastic pipes, wooden pallets, etc. Even snowboard boards, skateboards and other non-standard materials, such as an old basin, can be used.

Photo gallery: creative seats

Creating a hanging swing will not take much time

In skillful hands, even a snowboard can become a useful element of a children's swing.

Older children like non-standard solutions, for example, tire swings

The role of the seat can be performed by an old roomy basin

swing designs

According to the design features, the swings are:

• frame;
• suspended;
• floor;
• transformers;
• electronic type.

Age preferences for frame-type swings are children from 3 to 10 years old. Such structures have a great advantage - mobility. They can be placed in any area of ​​\u200b\u200bthe summer cottage or playground. They are strong enough to support the weight of primary school children.

Suspended swings are attached to the beam-beam. To do this, you can use chains, ropes, ropes. Their reliability increases with the use of a strong crossbar and subject to proper fastening.

Floor structures can be used by children under 5 years old. Most often, when creating them, plastic and metal parts are combined.

For very young children, you can make a rocking chair-transformer, which combines several elements at once:

• Chair for babies;
• mini chair;
• swing directly.

The modern world cannot be imagined without electronics. There are swings equipped with a special system, which may include:

• timer;
• "music Center";
• a device for setting the rhythm of swing movements.

They should be purchased only if your family has a newborn child.

Photo gallery: different swing designs

Frame swing 0 common type of structures

The design of the floor swing provides for their transfer to any suitable place

Good and comfortable for children in a hanging swing with a back

Electronic swing suitable even for crumbs

What functions can a swing perform

Swings, despite similar functions, may differ slightly from each other. This is due to the design of these structures, and their principles of operation.

Which adult does not remember such rides as boats? This type of swing can be used to entertain both children and their parents.

How cool it is to take off to heaven, swinging on "boats"

There are several types of children's structures, designated by one concept - a swing-balancer. Such devices include swings:

• "scales";
• "pendulum";
• "rocker".

Such fun fun is suitable even for small children. With the support of an adult, a one-year-old baby can also ride on a swing.

Only two people can ride on a swing-balancer

In our time, manufacturers of children's structures offer a rich variety of spring devices for swinging with balancing.

Of course, swings can be purchased at the store, but it’s better to work hard and build the swing yourself. Years will pass, but your child, who has already matured, will definitely remember the minutes of “ups” and “falls” on the swing that you made with your own hands.

Photo gallery: spring designs for kids

"On the seas, on the waves" - the motto of the design for children in the form of a boat

Sitting on the plane, you can feel like a real pilot

Such a ladybug will not take your child to heaven, but it will help to have fun

Springing, sitting in a helicopter, will appeal to all the kids

Preparatory work

If you decide to build a children's swing yourself, then you should do the preparatory work:

• determine the type of future design;
• specify parameters;
• draw a drawing;
• purchase the necessary materials;
• get all the tools you need.

Material selection

The simplest swing design is suspended. You can make them completely wooden or combine different materials. For hanging elements, metal chains, ropes, a strong cord, parachute lines or a rope are most often used.

With through holes in the crossbar, you will need special fasteners

For fastening, you can use special devices.

You can fix the swing with the girth of the crossbars using special carabiners

As a seat, it is best to use a polished board, because it is comfortable, does not crack in the cold, and will not cause discomfort to the child in the heat and cold. You can use improvised means - old seats from chairs, armchairs, etc.

A broken chair can be used as a seat

If you have more than one child or guests with children often come to you, then you can make a balancer for two. They are made from different materials. The advantages of metal swings are in their strength, but for an independent construction of such a design, you will need a good welder. Wooden swings are easier to make and less dangerous to use.

Material calculation

It is easiest to make a hanging swing with a metal support and a wooden swing-balancer.

The materials you will need are:

• 2 iron pipes for supporting pillars (d=74 cm);
• 2 bearings;
• 1 metal pipe (for the crossbar) 50 cm long (d = 150 mm);
• ready-made mortar for concreting;
• apparatus for welding;
• 2 metal plates no longer than 7 cm.

For the swing-balancer, prepare:

• any wooden material (average length - 2.5 meters). You can take an ordinary thin log, timber (thickness 40–50 mm) or a board about 25 cm wide.
• boards for seats (width - 30-40 cm, length - 45-60 cm) with a thickness of at least 30 mm.
• metal rod for support.
• hardware.
• paint or primer.
• 2 wooden handles (they can be made from a wooden rod with a diameter of 25 mm, about 60 cm long).

Schemes of street swings

You can facilitate the work of making a swing by drawing up a design diagram. Drawings are made independently (for individual parameters) or are taken ready-made from various sources.

Photo gallery: examples of drawings

The design of the swing must be very stable

Based on the drawn up scheme, you can build a frame swing made of wood

Be sure to indicate the dimensions of each part on the diagram.

Tool preparation

Depending on which design you prefer, you need to prepare:

• welding machine;
• drill;
• hammer;
• shovel or hand drill;
• screwdriver;
• grinder;
• hacksaw;
• roulette;
• plane.

Step-by-step instructions for making a hanging swing with a chain and a wooden seat

Having prepared everything you need, you can get to work:

In the selected area, dig holes for the support posts using a hand drill or a shovel. They should not be made too deep. Treat the lower part of the support posts with anti-corrosion compounds to avoid rust problems.

Using a hand drill, you will significantly reduce the construction time of the swing

Insert metal supports into the gravel and sand holes at the bottom. Fill the recesses with vertical posts with concrete. In order for the pillars not to move, you can use props made of wooden planks. Leave the solution to harden for 2-3 days.

For this stage, you can take a ready-made solution

Drill holes in the support posts with a diameter equal to the diameter of the transverse pipe.

Insert the crossbar pipe and weld it.

There is another reliable way to fasten the supports and the crossbar - by welding a special design (this option is very suitable for connecting wooden structural elements).

Using a special element for connecting parts, you can ensure the reliability of your design

In the central part of the crossbar, bearings are attached using metal plates. The bearings must ensure the movement of the swing in the forward / backward direction. The next steps are:

Pipes are attached to the bearings - seat holders. It can be 2 pipes with a crossbar welded at the bottom (under the seat) or a solid structure in the form of a smooth letter “P” (without corners). The swing can be hung on chains, a strong rope or a thick cord, which are attached to the holes made in the seat.

Bearings need regular lubrication

The seat is made of wood. Boards are attached to a metal pipe with self-tapping screws. A great idea for a seat is the remnants of an old chair or armchair.

For safety, you can use a one-piece metal structure on which a wooden seat is attached.

The finished structure must be painted or varnished. This will increase the life of the swing.

The condition of the swing should be carefully monitored. It is necessary to regularly lubricate the bearings with machine oil and tint shabby parts.

Before you invite the kids to ride, try the swing yourself.

Video: how to make a swing from a profile pipe in the country with your own hands

How to make a do-it-yourself wooden swing-balancer for a child

Based on the drawings made and armed with the necessary materials, tools, you can begin to assemble a wooden swing-balancer. The work is carried out in 4 stages:

• base installation;
• manufacture of rocker-balancer;
• assembly;
• product painting.

The diagram you have drawn up gives a clear idea of ​​​​the sequence of actions.

The base is the basis for the reliability of the design for children. This swing element can be built from a wooden beam (10x15 cm), a log (20 cm), boards (not thinner than 3 cm), fixing them in the intended place of the future swing. A lower frame about 1 m long is constructed from wood and vertical supports or racks are attached to it (using self-tapping screws) at an angle.

The rocker-balancer is easiest to make from a bar or a thick board.

For the entire length of the balancer (up to 2.5–3 m), 2 beams are laid parallel to each other, shorter beams (up to 1 m) are placed between them (on both sides). The entire structure obtained is fixed with screws or waterproof glue (for carpentry). You can use one board.

At the edges of the rocker, seats with handles are made, in its central part there is a hole for a profile pipe.

Handles, like all other wooden parts, must be perfectly smooth so that the child does not drive a splinter into the skin.

The assembly of the rocker arm and the base is carried out using two pipes: a support pipe and a segment mounted in the center of the swing. They are combined, a steel rod is inserted into pre-drilled holes on both pipes.

With certain skills, you can build a swing-balancer for children

Video: how to make a tire product

Decorating process

After the swing is mounted, you need to take care of their appearance. The easiest way to paint them with oil paint. This method is suitable for both wooden and metal structures. You can dream up and make the swing especially attractive for kids.

The easiest way to decorate is to paint

Do not neglect the rules for using a children's swing, which will help to avoid injuries. It is forbidden:

Getting too close to them while they are being used by other children.

Swing while standing, resting your feet on the seat.

Twist ropes, chains or other hanging elements.

Get off the swing before it comes to a complete stop.

Sit on the same seat for several children at once.

Before operating the swing, it is necessary to carefully inspect all nodes and connections for their integrity and functionality. Regularly lubricate the swing, preventing the appearance of rust and creaking. Make sure that there are no sharp objects, protruding bolts, unsanded wood sections in the structure.

Making a swing with your own hands is easy. The main thing is to adhere to the manufacturing technology of the product and the recommendations of specialists.