How to make a fence from a wooden stake with your own hands? Photo. Wooden stakenik fence: photo of beautiful options, prices, installation installation of the fence from the stakeholder do it yourself

(18 estimates, average: 4,36 out of 5)

All owners of dacha or household sites come when it is necessary to determine the territory of the territory fence. Design options Very much: Wooden fence; metal; concrete; brick. Each fence has its advantages and disadvantages. We will not stop on them, but select the simplest and affordable fence from a wooden stakenist to implement their project.

How to make a fence from the stakeholder do it yourself

Wooden fence is quite widespread. Not least due to its advantages:

Preparation of materials

Before proceeding with the manufacture and subsequent installation of a wooden stakenik, it is necessary to determine the final design of the fence.

The final decision must be taken considering the requirements of the general design site. The appearance of the fence must echo with the exterior of the house.

• The house built from red brick will initially look at the organic architectural ensemble, with a fence where the pillars are from the same material, and inserts from a wooden stakenist.
• A wooden dwelling from the bar usually involves the use of a fully wooden fence.
• A building with a stone foundation based on boot looks good with a fence having a similar basis.

The choice can be made of the following options:

• fully wooden fence;
• metal poles and lags in combination with a tree stakenist;
• stone or brick poles with a wooden stacate fence.

Deciding with preference, you can accurately calculate The number of required building material. Knowing an external perimeter of the site, we take a distance between the columns of 3 meters. Based on the selected design, we calculate the need in the number of components.

Regardless of what will be the pillars in the design, the length is considered. To the height of the fence we add the desired distance between the lower end of the stakenice and the earth and plus 1.3 meters, on which supports will be shuffled. Usually such a recess is necessary to ensure the high strength of the entire structure. Preparation of wooden columns to the installation usually comes down to processing them with antiseptics , in particular the underground part.

The total length of the lags, to which the stakenik is usually attached, for a wooden fence is to two spans between the columns. Station can not have a rectangular profile, but a round transverse diameter in the range from 6 to 10 centimeters.

All wooden products before installation inevitably exposed to planing. Processed surfaces are easier to finish impregnation operations, painting, with lacquer. Metal parts are obscured from rust and penetrating primer is applied to the outer surface.

Installation of fence

Installation of the fence usually start with the breakdown of the design. With the help of the cord, we carry out the size of the site, swaying the installation points of the column. Manual or mechanical brown pass the hole with a diameter of about 20 centimeters to a depth of 1.3 meters.

Wooden or metal pillars put in pitsAlign the straightness of the cord. Level in vertical level. We take out the empty space between the columns and the impressive sandstop-cement mixture with the addition of granite rubble or broken red brick.

If in this area it is noticed the freezing of the soil, then to eliminate the extrusion of the main supports during the frost, pillars instead of the building solution, fall asleep by boot small fractions and tram.

Before installation, wooden poles for the entire length of the underground part are winding up from below a wide layer of rubberoid with overlapping at least 15 cm for waterproofing.

After grapping the solution to be made installation Stable. Rectangular or round wooden lags are attached to the pillars of nails or self-drawing. The splicing of them is done by roaming half the thickness. Sputtering seams did not prevent themselves so that they are in various places.

In the case of using metal pillars and stable it is applied hard fastening Welding or through special brackets with galvanized hardware. Lags are spliced \u200b\u200bwith welding or with metal plates with fastening bolts with precipitated nuts. Now the power design of the fence is considered absolutely ready.

Go to no less responsible stages of installation of stakenika. Multiple ways to place it determine the uniqueness of the fence. Instead, so familiar row with a constant step, you can use with an increasing or decreasing gap.

The angular placement of the boards will bring a variety of fence in the style. The use of carved stakenice will make an individual uniqueness into the appearance of the manor. Semicircular or bottom, alternation of various sizes of boards and many completely other variations are available for implementation.

So that the courtyard is not viewed, you can apply chess order of installation. One board in front of stirred, and the second with a gap relative to it or without, behind. By independently adjusting the gap, see the transformation of the direct visibility of the land plot and the injection of the fence.

Fastening the stakeholder to wooden lags is done in the old manner iron nails or galvanized screws. The boards are screwed to metal strains.

Finishing work

In order for the fence from the stuff to serve more than a dozen years, the tree should be immediately treated with antiseptic materials, and then paint or open lacquer. This operation will have to do systematically. Once every 5-10 years, the board is checked for damage from fungus, mold. Spoiled stakeniki replaced with new . The whole design is again processed by impregnation and opened with varnish.

The fence from a wooden stakenik - once semi-forgotten, and now the type of fence becomes trendy, gradually displacing a popular metal. Tree - universal and warm material, a symbol of home comfort in a temperate climate. Wooden stakenik fences are almost every village of Russia. Although they got the name from the German Word of the Six or Post.

Classics of the genre

The specificity of the device of the fence makes it durable and strong, the material gives comfort and decorativeness, the main advantage is the variability of the intended building. Dimensions - width, height and length - you can give any, and simple staining will change even the most unsightly row of wooden plates.

The stakenatnik was obtained by its name due to the specificity of the device from several standard elements. The developed technology of installation of such proceedings makes a fence functional and strong, relatively inexpensive. Diagram: Longitudinal planks are fixed on longitudinal rails.

Floor on the site

They are fixed on durable support columns covered in soil or concreted.

The craftsmen, in the desire to decorate the ordinary, moved away from the boring German standard. A simple fence from the stakenik is sometimes a real work of art.

In the photo - the pseudorussian style, decorated with the easiest tools.

Before painting

A wooden fence from the stakenice, built in the country, from the functional barrier easily turns into a decorative fence. This is due to a different way of fastening, a whimsical fantasy of the owner who worked on, unusual coloring or the use of rivers of different lengths.

It is difficult to say what exactly returned to life and the construction of the practice of installing fences from a wooden stakenik:

• fashion on natural materials;
• inherent decorative wood;
• relatively democratic cost;
• nostalgic mood for old good times, when such fences were the most common cause and covered every meter of the outskirts and villages;
• the possibility of installing the stakeholder with your own hands, without special tools, independently and unmistakably calculate the necessary merar;
• option Order Fence at the construction company;
• almost any size of fences.

Decor fence

Perhaps a combination of benefits made in demand wooden fence from the stakenik. The use of fantasy and skills give rise to so beautiful fences that passersby stop admiring. And for a long time, no one comes to mind to consider that the choice of the host forced to make the lower cost of the fence from a wooden stakenist.

The photo shows a capital building in the style of tycoon.

Beautiful fence for a private house

Stakenatnik - the best choice, possession, cottages, town and rural housing. Its indisputable advantages include:

• diverse designs, subordinate any whims of the host;
• presence, if necessary, additional strengthening, shields styled to close the lumen, metallic or;
• variable methods of placing RECs (stacking options: Chess, Christmas tree, oblique cross, bars, sruba imitation);
• the presence of modern formulations for impregnation, allowing to extend the long life of the facility, and at the same time emphasize the natural beauty of the tree;
• the ability to paint beautifully using modern paints with their bright color scheme, if necessary;
• the reliability of the design, which can be additionally strengthened by applying brick or metal poles.

In the photo - a simple stakeholder series. The comfort and sea of \u200b\u200blight.

Democratic Option for Rustic House

You can buy such a material in almost any construction market or in the supermarket. Stakenatnik from other materials (or) it is possible to order a turnkey or make it yourself. The fence calculator can be found on the builders sites. To calculate the approximate cost, it is enough to make measurements.

How to make a fence from the stakenik, can be found in the information space, but any preventive owner knows the method of facing simple and durable hedges. He will prefer, binding materials, start assembling the fence to be proud of the barrier made by their own hands.

Original and beautiful hedge

Preparation of material

The future builder has 2 ways: he can buy ready-made rails treated in specially necessary parameters (as a last resort, it will have to cut a little bit) and start the installation on the day of purchase. The craftsmen who have equipment, prefer the second way, more complicated: they make stakeholders personally.

Drawing for mounting design

Montage with your own hands

The scheme of the usual hedge is extremely simple. At a distance of 2 meters from each other, a durable pillars are laughed, capable of withstanding the severity of the stakenice, even in a wet form (when wetting a tree of heavy). They are equipped with pits, a depth of 70 cm (for strength can be meter). In order for the fence to be beautiful and even, the pit is pre-marked with spicy, and between them stretch the twine.

The distance is measured by a roulette, it should not exceed 3 meters.

Such a fence will serve for a long time

Installing columns and guides

Poles for pillars must be equipped accordingly, with an indispensable consideration of the soil type. They can be made a brown or dig, it is not fundamentally, but it is necessary to pour sand and gravel to the bottom and thoroughly tumped before installing the pillar and produce a concrete fill. For a simple fence in the country, you can do without concreting. And for the Fortress of the structure - to the meter to reduce the distance between the supports.

Installation option without pillars concreting

But the optimal option is to determine the pillars, so that after the installation produced, do not repair as a result of adverse weather conditions. Experts are confident that in Concrete, the tree rotes faster, so it is better to lay sand and gravel, carefully trambus every layer. Stills for strength are additionally processed. As a democratic option is used by bitumen.

Stakenice Section Set

Lags are attached to a wooden post, but do not forget that we only install them after the concrete will find it well. Metal brackets are used to fix them. The types of fences are different for their fastening, if the design is simple, people use self-tapping screws or nails.

Another installation scheme

How to properly dial the militant part, is also solved in different ways:

1. The block from the crossbar and the stakenik is going on the ground, and then fastened as a whole to supports.
2. Lugi are installed on the pillars, and staketins are nailed to the finished substitution.

For a simple fencing passing the light, the optimal set of sections. It makes it possible to work at once to several builders: some collections, others fasten ready shields to the alms.

In Russia, the tree has long been widely used as a building material. From it build log houses, frames for windows, interior items, kitchen utensils. This natural material allows you to create an atmosphere of internal comfort and coziness. Wooden fence from the stakenik is one of the most popular types of fences in country construction, which is simply indispensable when arranging a rustic area. Such a fence on the one hand delineates the boundaries of the site, and on the other hand, it does not shadow its territory.

Fencing from the stakenik can be given any height, shape, color, and even the distance of the lumen, so that they acquire the original look and their appearance complement the design of the country site.

The fence from a wooden stakenice is used as a reliable fencing of the household plot, the element of zoning the territory, the decorative framing of the bed and flower

Stems with flowers, filling the lumens in gaps between vertical strips, give the fence more attractive

The constant popularity of this type of fence is explained by a number of parameters and properties, among which:

• Universality. Wooden fences fit perfectly in any terrain landscape. They are perfectly combined with any other bases, organically fit into the interior, made of stone or brick, concrete or metal.
• Easy installation. Installation of fence from the stakenice can be done by any dacket and the owner of the country house independently, without resorting to the services of professional masters.
• Ease of care. Caring for the fence is only in timely staining of the surface and eliminate defects that may occur during operation as a result of mechanical impacts and seasonal precipitation.
• Reliability. A tall wooden fence will speak not only by a decorative element of landscape design, but also a reliable protection of the owners of the site.

One of the advantages of the stakeholder, in comparison with the traditional solid fence, is the possibility of planting plants right at its base.

• Support poles. They can be made of metal pipes or thick bars.
• Staketina. Unbroken rails are made of edged or planed boards.
• Stated. The transverse slats plated horizontally between the support pillars, a length of 2-2.5 meters are made of 40 mm cross sections.

Choosing a material to make a fence from the stakenik, you can go in two ways: to purchase a ready-made stakenik or make it yourself from the boards. The first method saves time. The finished fence can be installed on the day of purchase. But a substantial disadvantage can serve as poor-quality raw wood, which protrudes the basis for the stakeholder, which in the process will "lead" the fence. Choosing the second path, the owner will need to make efforts to spend several days to make all the elements of the fence. But with the result, he will have a stakenik who fully corresponds to his ideas and wishes.

If the material is not succumbed enough, it is necessary to use special dryers for the forest, because in natural conditions the drying can stretch for several seasons

Forest drying service, as well as cutting alternate and staketin, can be ordered in a place where they are engaged in the manufacture of wood products. When preparing the material on its own, it is necessary to carefully stored and sand all the tops.

Wooden Stakenice Top

The bottom of the wooden support pillars should be wrapped with a hot water. This will prevent wood rotting and extend the life of the structure.

Installation and installation of fencing

Stakeholder arrangement is performed according to the same principle as the construction of other types of fences. First of all, the direction of the future fence is determined. It must be released from weeds, bushes and branches of trees that will interfere with construction. Then the beacons are tensioned on the cleared territory and the stretched lace is planned at the poles. The distance between the columns should not exceed three meters. Otherwise, long spans between supports can serve as a savage of across the severity of Staketin.

The reference pillars can be installed directly into the ground, but to create a stronger structure, it is better to erected with the use of fill with cement-sandy solution.

To install the columns, it will be necessary with the help of a bera. Eat a hole whose depth is determined. On average, a depth of 1.3 m

Install the columns on a 20 cm gravel pillow, which allows you to prevent the squeezing of the support when the soil is freezing. Vertically fixed columns fall asleep alternately layers of concrete and soil solution.

After installing the columns along the line of the fencing, you can install between them stirred. In principle, it is possible to set the fence in two ways: when first first, the crossbars are attached between the columns, and after them the stakenik is nailed, and during the second, the spans are collected separately and fixed to the supports already blocks.

The first staketine is attached vertically, and the rest are aligned by the T-shaped pattern, in which the width of the leg letters "T" is equal to the step of the staketin, and nailed

On average, the distance between Staketins is equal to the width of the very well. Create transverse strips on wooden support pillars with the help of self-tapping screws, bolts or ordinary nails. Metallic columns are fixed on a specially welded corner for fastening timber.

Finishing and decoration of fence

The finished fence remains only other negatively affecting factors.

It is necessary to close all the cracks and chips with putty compositions, to increase the stakenik antiseptic, and then cover with varnish, veneer or paint

Freshly tireless film-forming drugs are bad and shortening. To "stubbind" the surface of the tree, you can clean it with medium-hearted emery paper.

Morilka is an excellent preservative, protecting wood from the development of microorganisms and mold

Varnish will protect the tree from moisture. Using the simulator and transparent varnish, you can also imitate various wood species.

Choosing a fence for a plot is not easy task - it is necessary that it is reliable, durable, beautiful. All these requirements are responsible for the fence made of metal stakenik (Evrichnik). Climble is problematic - not that stiffness. Breaking it "boring" - usually, lovers to lose weight are limited to the fact that they will move a couple of planks. Beauty, of course, the criterion is subjective, but such fences look better than the same solid. In addition, they are not so susceptible to wind loads, which allows you to save on the support pillars. Additional plus - they are blown. In general, a good option.

What is a metal stakenik

Metal stakenik makes a galvanized steel sheet. The sheet forms a relief, after which it is cut into stripes-staketin, is covered with protective compositions, painted. The planks of a certain height are obtained. Usually height - from 150 to 180 cm. For the collection of the fence, still supporting pillars are needed (most often 60 * 60 * 2 mm), the tents (two or three crossings, which come between the columns) and fasteners.

Types, shapes, profiles

The thickness of the European Metal can be from 0.4 to 1.5 mm. The most common - from the steel thickness of 0.5 mm. Staketina width - from 80 mm to 128 mm, length - up to 2 meters.

P and M - shaped metal stakenik profiles

There are metal stakenik with different profile: n (rectangular), m shaped and semicircular. M-shaped have more ribs, respectively have greater rigidity. But there are also P-shaped, in which the grooves are molded in the back. So in this case it is already difficult to say which one will be tougher. Most likely, the last, especially if the edges are rooted.

Semicircular also have greater rigidity, but more difficult to form and have a higher price. For greater strength, additional grooves can also be formed along the long side.

In general, the more rigid ribs, the better the strapbea is resist in length. But with the complication of relief the price becomes higher. Since she is rather big, usually you have to search for a compromise. In any case, the bar must withstand your attempts to bend it.

What to pay attention to when choosing

When you choose a metal stakenik, it is advisable to look at the batch offered to you live. It may be declared the same metal thickness, and in practice it turns out that the edge of the plank from one batch can be bent with a finger, with another party, such a focus is unable. And this is one manufacturer. The point is as a metal batch, and it is rarely stable.

The rooted edge, several layers of protective coatings - these are signs of a good metal stakenist

Be sure to pay attention to the edges - better if they are roles. Firstly, this is a more attractive appearance, secondly, the large stiffness of the stakeholder, thirdly, the sharp edge is bent and it is impossible for them. The disadvantage of the stakeholder with the rolling one is a higher price, as special equipment is required and extra time for processing.

If we talk about the products of specific firms, the Grand Line (Grand Line), Barrera Grande, Nova, TPK Center, Finfold, Unix (UNIX) is popular.

Methods of coloring

It is worth sorting out in the way of color. There is an iron stake with bilateral and one-sided painting. With one-sided, the back side is covered with a layer of soil without staining. It has, respectively, gray. The fence made of metal stakenice painted on the one hand, from the inside of the gray section. It is not bad - he is not striking. If you do not suit you this option, or buy with bilateral painting, or Kraft yourself. Paint take "for roofs", picking up a suitable shade. Note that the metal died with a brush looks ... not very. If there is a paintopult, the appearance will be quite good, although not perfect.

So it looks like "starving" painted on one side of the fence made of metal stakenik

It is also necessary to take into account that there are two types of staining of the metal stakenist:

1. polymer coating;
2. powder paint.

The first method is much more reliable, since the application technology requires special equipment and harsh compliance with technology. As a result, such a stakeholder withstands increased mechanical effects. Even if the scratch appears in the coating (although it is necessary to try), the metal does not rust, as there are still protective coatings that prevent the appearance of rust.

Polymer coating - the best choice today

Powder spraying, in theory, no worse. But only if it was done according to the rules: a protective coating was applied to the projected metal, and on top of it - powder paint and baked it in special chambers. But the essence is that you can also apply in the "garage", and somehow you can burn it there. The result will only be completely different. In addition, there are ready-made sheets of Chinese origin. In them, paint is applied to the workshop, but, often, directly on the neglished steel surface. Externally, it is impossible to identify all these nuances, and after the slightest scratch, rust appears. So the polymer coating is more "safe."

What could be a fence made of metal stakenik

Metal fences can like or not, because there are no tastes. But in terms of practicality, they certainly won. Installing once, you still do not remember the fence for years. It should not be painted so that it has a decent appearance, since good quality paint is kept for years without visible changes. And this is one of the important factors that are forced to think about installing such a fence.

On tape foundation

With the foundation and pillars from clinker bricks

Methods of installation

There are single-row and double-row (double-sided, chess) Method of installation of metal stakeholder planks. With a double row, the planks are located on both sides of the taper, and so that they even on a centimeter overlap each other. Therefore, the distance between the planks should be slightly smaller than the width of staketin. With this installation, the slats on the traffic point meter fence will be required by 55-60% more. But the fence is obtained practically imperishable - only at a certain angle can be seen a small part of the area. And this is despite the fact that the fence will not be solid and all the "charms" of a continuous fence will not touch you.

Most often, the plank is mounted vertically, but there is also a horizontal installation method - it can also be single-row or double row. It looks horizontal fence more exotic. With a double row (double-sided) mounting of the slats, it turns out at all opaque.

The disadvantage of this method of installation is that special pillars and intermediate poles are needed, which will provide the required stiffness of the structure. Another nuance: the planks usually produce up to 180 cm long, longer have to be ordered, and it costs extra money. So either you have to raise the poles more often, or overpay for non-standard size.

Dimensions and distance

When installing in one row, the gaps between the straps can be different. The exact distance is chosen arbitrarily, depending on how "transparent" want to make a fence. Most often, the distance between Staketins is 35-50% of the width of the plank. But this is not a rule, and with smaller, and with big gaps.

When installing the chess, if you do not want your courtyard at an angle, the planks must overlap 50% width of staketin or more. If the "viewing" is unimportant, you can put them so that the edges overlap only by 1 cm.

The height of the fence is chosen depending on the wishes of the owners. If you want the courtyard to be as close as possible from an extraneous eye, the length of the bar must be from 180 cm. Taking into account the fact that they will be slightly raised above the ground, this is enough for the overwhelming majority of people could not look at your territory.

If you do not care if there is something visible through the fence or not, you can take 1250 mm and 1500 mm. In the first case, the fence will end somewhere at the chest level of passersby, in the second - at the level of the eye or just below (look at the figure in the figure), and this is without a foundation.

The width of the span of a vertical fence made of metal stakenik - 200-250 cm. It is at such a distance that there are poles, then two or three crossbars are fixed between them. These crossmen are called "lags" or "tents." For a stakeholder up to 150 cm high, two are sufficiently cross, for higher, it is better three.

Types of fillings

There are some more varieties of filling the spans (distances between the support pillars). The easiest way to install the direct method is when all the strips of the same length. On top of such a fence, it is possible to start the P-shaped bar from the same material (sold there where both the Ershtroker is sold. In addition to aesthetic load, it still covers metal cuts, which increases the service life of the fence.

All "waves" require trimming of most slats for a certain distance. One "wave" is made on the span with a step of 50 or 25 mm. With a step of 50 mm, the height difference between the shortest and the longest straps is significant, but the fence looks more openwork. In the case of "waves" in a step of 25 mm or with a "double wave", the difference is smaller. The top planks here are much less likely, but they can also be installed. Only at the site of the "Waves" fracture will have to trim the sidewalls and bend.

Features and installation rules

When installing the fence from a metal stake in the middle lane of Russia, it is recommended to install pillars from the profiled pipe 60 * 60 mm (you can 60 * 40). For the cross, it is more convenient to take the same profiled pipe, but with a cross section of 40 * 20 mm. In this case, the fence will accurately withstand wind and snow loads.

When installing the setting step - 2 meters. If the cross is two, they are fixed so that it is 25-35 cm to the edge of the bar, with a staketin height from 150 cm and more, a distance of 30-35 cm, with shorter - 25 cm. But, with a fence height above 1.5 m, It is better to do three lags, and not only in the regions with strong winds. Just with two lags, it turns out too much a distance between the fastener, which is why the planks are easy to push.

There are two ways to fix planks: on a screw and rivets. Self-tapping screws are installed on both edges of the bar on each of the cross. That is, if two are across two, it is necessary for each bar for 4 screws / rivets, if three, then the fasteners need 6 pieces on staketin. You can, of course, fasten to one self-tapping screw or rivet on the cross, installing it in the middle. But in this case, it is not necessary to push the stakes with your hands easier - and you do not need to climb through the fence.

So mount faster, but it is "purely decorative" fence

Which type of fasteners choose? Self-tapping screws are easy - in this, they are plus. But they are also easily unscrewed that, under certain circumstances, it may be a minus. Rivets require more time to install, but also to remove them much more difficult. What to choose? On the front part of the fence or if the fence is for a long time, it remains unattended (giving seasonal visits), it is definitely worth putting rivets. Of course, if the attackers will enjoy the goal, they will cope with rivets, but it will be more difficult to do it. When installing the fence between neighbors in permanent residence homes, it is quite possible to mount a metal stakenik on a self-tapping screw.

How to make it yourself

As you probably noticed, the metal stakenik is produced by almost the same technology as a professionalist, and there is a sheet cheaper. Therefore, many appear idea, make a stakenik, dissolving a strap strap. In principle, it is possible to do this if you are able to cut strictly along the line without any noticeable deviations. But for cutting it is necessary to use scissors for metal - sparkling or manual. Bulgarian cut in no case, because it burns the protective cover. So work is not difficult and time will take a lot. If you do not scare it, you can try.

What is the lack of a homemade stakenik from the professionalist? Everything is obvious: the edge rarely happens even, since manually do it is difficult. In addition, the cut turns out to be unprotected and can start rust. Of course, it is possible to wash the sections of the primer / paint, but that all layers are legally normally, an absolutely clean surface is required. That is, the sections of the sections initially need to be discussed (not so difficult, but takes time), then still degrease. Only in this case the protective coating will be really high quality.

It is advisable to fade the edges - it will give a homemade stakeholder greater stiffness, because additional reliefs rarely form on a straightener. He "keeps" the form due to its size and alternation of waves.

1. Materials and tools
2. Manufacturing technology

The fence from the stakenik is one of the most popular types of fencing, with which the country's cottage is addressed. The main thing is to implement it correctly. Such a hedge has ensured popularity due to a number of advantages, the main of which are the low cost of construction and appearance.

Materials and tools

The installation of a wooden fence does not require special devices, if it comes to combined structures consisting of several different type materials, such as a stone or brick. Bearing vertical and horizontal support supports can be made of wood or metal.

To install the stakenice, you will need:

• wooden timber 50x50 mm;
• wooden timber 20x40 mm;
• nails or self-tapping screws;
• antiseptic;
• paintwork.

The square timber is needed for the manufacture of vertical supports, and its length is planned according to personal wishes: the height of the future fence is determined for itself.

The support is powered into the ground at least half a meter, so it is necessary to add 50 cm to the desired height of the element for the fence.

The short cross section (20x40 mm) is designed to horizontal amplification of the flirting of the flush. Its quantity will be directly dependent on the length of the fence installed. Nails or self-tapping screws are suitable as fasteners. The second option is more preferable, because the screws are not loosened during the operation of the structure.

Fasteners need to be purchased from galvanized metal, which does not rust from exposure to atmospheric phenomena.

Antiseptics and paintwork materials on the market. It is necessary to choose funds intended for external work. From the tools you will need a woodcutter or an electrolovka. If you trig a plate with nails, a hammer will be required, and the self-tapping screws are better secured with a screwdriver. The shovel for mounting the support columns is useful.

Manufacturing technology

A step-by-step scheme for assembling a stakeholder with their own hands will help properly organize and perform work from beginning to end.

1. At the first stage, it is necessary to properly prepare wood: all natural material must be impregnated with an antiseptic several times using a conventional painting brush. The process is quite time consuming, but it cannot be ignored. Such a measure will help ensure the protection of the tree from environmental impact, will save from rotting, extending the service life.
2. Now you can start installing the supports. We start work with marking places for their installation. In places where the hedge changes the direction (on the corners), we set the pegs and stretch the solid rope between them. Then you need to calculate the number of supports. To do this, measure the distance between the spikes and divide it at equal intervals, the length of which does not exceed 2 meters. The resulting value will be a step between carrier pillars, and on the site of their installation it is necessary to dig the pits, taking into account that the support should go into the ground at least half a meter, below the freezing point. For a long and reliable service, supporting structures are crushed with large gravel and the land will be trambed. Increasing the use of wooden supports helps Laying the rubberoid to the holes shouted for columns, and the supports themselves turn around the same reference to the places of their shock in the ground.
3. In the third stage, transverse guides are usually mounted. The main thing is that each stream is located strictly horizontally. It is easy to control the construction level. Horizontal supports are mounted in two places (at the top and bottom of the fence), however, in the case of a high fence, you will have to install an intermediate guide. They are fixed to the vertical supports of the stakeholder self-stakes or naught.
4. The final step will be the installation of wooden slats of the stakenik directly on the fence. The longest, but very simple process is that each staketine is screwed strictly vertically at equal intervals. If you pull the thread on the lower edge of the staketin, it will allow one level of their placement.

At the fourth stage, the assembly process ends - a fence from a wooden stakenik is now ready to operate. It remains to paint it into any selected color, but many wizards additionally decorate the elevation using non-hard techniques. This applies to the design of the top edge of the staketin, which is given a certain form.

The fence sections can be performed in the form of a wave or arc. To do this, the markup is applied to the fencing, under the template there is a trimming. Staketins are sharpened on both sides in the shape of a sharpened pencil - it will save the distance from unauthorized access.

Often there are fences from stakeholder with carved rolls - it's about the creative approach of the carpenter. You won't call such a job.

Alternative to wooden supports

No matter how the future supports have prepared and have been processed, but the tree in durability is inferior to the metal. If you want a wooden fence from the stakenice to serve for a long time, and its service life is not limited to 15 years, it is better to use a metal base that is mounted in the same way, with the exception of several points. The columns are made of metallic pipe with a cross section of 40 mm, fixed in the ground with concrete solution.

To ensure the optimal adhesion of the carrier element with concrete to the bottom of the vertical supports, trimming reinforcement or metal plates welded.

The horizontal countries are made of smaller diameter metal pipe and weld them between vertical support elements, following the horizontalization of the placement using a level. Then each staketin is fixed on the previously built metal frame of pointed self-drawing. It turns out a wooden stake, but reinforced with a metal basis.

Even if staketins come into disrepair over time, they can be replaced, the supports will remain the same, and this is saving funds.

A wooden stakenik has a lot of options, and brickwork can be used as the basis, which, in combination with natural wood, gives a special effect. Instead of brick, if the means allow, lay the spans from the stone. For such a massive design, the foundation will be required. And this is a more laborious process.