A bench made of two old chairs. Do-it-yourself bench from old chairs New life of old wooden chairs: feeders for large dogs

Then do not rush to get rid of it. Applying your imagination and our tips, you can make a new set out of this furniture. In this homemade product, we will tell you how to make an original bench from old chairs. This option is not only convenient, but also very interesting. You can put such a bench in the yard of your house or in the country. The original bench will become an unusual piece of furniture.

To make this homemade product, you will need the following materials.

Materials
Old chairs (4 pieces);
Saw tape;
Jigsaw;
Drill and drill bits for wood;
Dowels (wooden);
Remover for varnish and paint;
Joiner's glue;
Putty knife;
Wood varnish;
Paint;
Brush;
Boards;
Meter;
Marker;

Step 1.

You must first take two chairs and carefully remove the horizontal racks that are located in front of the seat.

Step 2.

Now we take the remaining chairs. Using a meter and a marker, you need to make a mark where the cut line will go. This line should be slightly lower than the A-pillar. Take the saw and carefully cut the legs along the marked line.

Step 3.

At this stage, you need to remove the old varnish and paint from the chairs. To do this, apply a special product for this job in an even layer. Withstand the required time (it is indicated by the manufacturer of the product). After the required period, carefully remove the old coating. To facilitate the work, you can use a spatula, as well as sandpaper (fine-grained)

Step 4.

Now you need to drill holes for the dowels in the racks from the front and end sides. First you need to make a marker with a marker where these holes will be. Then take a drill and drill holes.

Step 5.

Take the dowels and insert them into the resulting holes. Before that, be sure to grease the dowels with glue (carpentry)

Step 6.

After the dowels are firmly glued, it is necessary to assemble the future base of the bench. This must be done, as shown in the photo below. All components of the bench are fastened together with self-tapping screws. After that, the entire surface of the bench is sanded again.

Step 7.

At this stage, we will make the bench seat. For this we need a board. The board should be adjusted to the size of the bench. It is necessary to mark the desired length, and cut off the rest. Do the height of the back at your discretion.

Step 8.

If you decide to make a seat from several boards, then they must be glued together with wood glue. After that, the entire structure should be clamped with clamps and wait until the entire structure is completely dry.

Step 9.

Now you need to glue the seat to the base of the bench. Coat the base and seat with wood glue. Place weights on the board, and also clamp it with clamps.

Step 10.

Wait until it is completely dry. After that, take masking tape and paste over the surface of the seat with it. The rest of the bench should be painted with a special wood paint.

Don't rush to throw away your old kitchen furniture. Your diligence and imagination will help the chairs from the headset get a new life, for example, in the form of a bench. It is not only convenient, but also interesting, because you can use it not just as a bench in the yard. A bench made of chairs can become an independent and original piece of furniture in the interior of a living space.

Materials

To make a bench from old chairs with your own hands, you will need:

four identical chairs;
sandpaper;
paint and varnish removers;
putty knife;
band-saw;
drill and drill;
wooden dowels;
joiner's glue;
paint for wood;
brush;
wood varnish;
board;
jigsaw;
meter.

Step 1. Take two chairs out of four. Choose those that are not so attractive in appearance. Carefully remove the horizontal uprights at the front of the seats.

Step 2. For the remaining two chairs, you will need to cut off the front legs. Before that, using a meter and a marker, draw the cut lines. They should run below the A-pillars on the seats. Cut off the unnecessary part of the legs with a circular saw.

Step 3. Apply varnish and paint remover to the surface of the prepared parts of the bench. Leave it on the surface of the chairs for the time specified by the manufacturer. After it expires, remove the old coating. For convenience, you can remove rough layers with a spatula. Sand the surface of the chairs with a fine-grained sandpaper.

Step 4. On the prepared uprights from the front side and on the uprights of the chairs from the front, mark with a marker in the places where you will drill holes for the dowels. Before using the drill, be sure to check the correctness of the marks. Drill holes.

Step 5. Insert the wall plugs into the holes at the end of the uprights. Pre-grease them with wood glue.

Step 6. After the glue has dried, assemble the bench base. During assembly, in addition to wood glue, fasten the components with self-tapping screws. Sand all surfaces again.

Step 7. The seat of the bench will be a board fitted to the shape of the chairs. To do this, by trying on, apply the markings of the appropriate shape to the surface of the board and cut everything off with a jigsaw.

Step 8. If your bench seat, as in this case, consists of several boards, glue them together already fitted with wood glue. Clamp the structure with clamps and wait until the glue is completely dry.

Step 9. Glue the seat to the base of the bench. Send weights to the board and secure it with clamps.

Step 10. After the glue is completely dry, cover the surface of the seat with masking tape. Paint all other parts of the bench with wood paint.

Step 11. Remove the masking tape and cover the seat board with stain.

Step 12. Paint the entire surface of the bench with wood varnish.

After the mat is dry, lay some pillows on the bench and enjoy your rest.

Do you have a couple of unnecessary chairs that are idle? Today we will tell you how to make a cool French-style bench out of them, which is ideal for decorating an interior.

On our balcony we found old, wooden chairs, which are about 50-60 years old. They had a soft seat and were made of fine wood. At the moment when we took up this business, they were already falling apart.

We called the bench French because we saw a similar bench from Ballard Designs. We also want to emphasize that this is not one of those benches that are made according to the principle of lining up chairs in a row, where plywood is later applied to them. After all, it looks a little strange, we will make a bench in a classic style.

If you still make such a bench, you will surely have your own thoughts and ideas on how to make it better. We will be glad to accept your advice and work. Send them to us by mail, we will be happy to share them on our website.

After looking at our chairs, we found out that they are fake, although they looked quite expensive. After that, they were safely taken to the farthest corner of the workshop, to await their fate. At that moment, we simply could not get rid of them. One fine day in May, one of our craftsmen suddenly started making our bench without us. This is not like him, because usually we have to persuade him for a long time, to do something, of course, except for custom-made furniture, this is his direct responsibility. So, let's begin!

Step one: Find chairs.

“We need to find two chairs that look good from the outside. If your chairs have a slight backrest angle, that will be fine. This backrest will create a comfortable and not very angular look. It is desirable that the seat of the chair be screwed with nuts and bolts to the main body. This will make it easier for us to attach the base under the bench to our chairs.

- Remove the front legs and seat. On our fake chairs, everything was kept on glue, we easily tore off the two front legs, and removed the seat. Thus, we are left with two chair backs.

If you can unscrew the front legs on your chairs, it is better to take this opportunity. If the legs are broken off, parts of the tree may remain sticking out.

Step two: We make an inseparable seat.

- Make a rectangular frame. Any length of the bench can be made. It depends on how many people you plan to fit on it. We took the materials for our frame in an old ikea worktop. After the frame is ready, it must be fixed with screws as shown in the picture above. Use strong screws to fix the frame.

- We fix the frame. We drilled holes for the chairs' seats, if they weren't fake, and attached our frame. On each side, we made three holes and screwed in three screws to distribute the weight evenly. A little lower, we drilled a couple more holes, and screwed in a future shelf for various things. Our goal is to make the bench safe to sit on, so don't spare the bolts, we ended up with 7 screws on each side.

Step three. Create the bottom shelf.

“Even after we attached the main frame to our bench, the structure was still pretty shaky. To avoid falls and breaks of the bench, we decided to fasten the two sides with another wooden rectangle. We will use it as a shelf. Carefully measure the distance between the legs, and do not forget about the main principle "Measure seven times - cut one." Do not repeat our mistakes, measure correctly.

- We nail the partitions. We didn't want our bench to look awkward or bulky. Instead of a plywood sheet, which was originally supposed to be located on the bottom frame, we nailed 5 crossbars. Used for this ordinary, small carnations.

Step four. We skin and paint.

— Remove all irregularities with sandpaper. After that, if there are empty gaps between the frames and the frame, we fill them with construction foam or plaster. After that, once again we go through with sandpaper. If you leave the gaps unfilled, over time, moisture will accumulate there and gradually destroy our bench from the inside. If you don't have any plaster or foam on hand, just paint all these holes.

— Bench painting. We used spray paint, a delicate cream color. Three uniform layers were applied and allowed to dry.

The cost of a spray paint in Tashkent starts from 10 thousand soums. Not at all more cost for an entire bench.

Step five. Making the seat.

— To make the seat , we need a piece of plywood, chipboard, MDF or fiberboard. From this we will build the upper part of the bench.

- Upholstery the seat. For soft filling, we used a synthetic winterizer. If you don't have one at hand, you can pull out the cotton wool from the old mattresses. There she is in abundance, she is quite suitable. Or the quickest and cheapest way is to buy a small piece of foam. It is sold in stores with furniture fittings or household items. goods. It is necessary to spread the filler on plywood so that there is about 1 centimeter of void around the perimeter. The material for covering the bench is also of your choice. We used a piece of unnecessary sheet. Covering our soft filler with a cloth, we wrapped the edges under the bottom of the bench and stapled it there.

- We attach the seat to the body. For mounting, we used an L-shaped bracket. Although everything would have held perfectly with ordinary bolts, we decided to protect ourselves and use them.

Our bench is ready! All we have left is to decide whether the pillow will be located there or not. In an unfamiliar environment, with needles in hand, we decided to try. Taking the remnants of the sheet that we had left from the cover of the bench and the synthetic winterizer, we began to sew and fill our pillow. It turned out quite well for people who have been making custom-made furniture for many years. Making such a bench will take you half a day, or maybe all day. If you want to suddenly do something with your own hands, this bench is a great option to start with. In the courtyard of your own house or in the country, this piece of furniture will be not only useful, but also beautiful. And having decorated it with decorative pillows, the bench will be an excellent tool for decorating a room or site.

I hope your bench is as strong as ours. It does not stagger or even sway under a load of about 200kg. And if something went wrong, or you just don't have enough time, patience or strength, but you want to get such a bench. You can order it in the custom-made furniture section. And we will not tell anyone that it was not you who did it.

We think this is a great way to save old chairs and give them a second life. Send your work to us by mail. We will be glad to show the world what you have done.

Materials

To make a bench from old chairs with your own hands, you will need:

four identical chairs;
sandpaper;
paint and varnish removers;
putty knife;
band-saw;
drill and drill;
wooden dowels;
joiner's glue;
paint for wood;
brush;
wood varnish;
board;
jigsaw;
meter.

Step 1... Take two chairs out of four. Choose those that are not so attractive in appearance. Carefully remove the horizontal uprights at the front of the seats.

Step 2... The remaining two chairs will need to have their front legs cut off. Before that, using a meter and a marker, draw the cut lines. They should run below the A-pillars on the seats. Cut off the unnecessary part of the legs with a circular saw.

Step 3... Apply varnish and paint remover to the surface of the prepared parts of the bench. Leave it on the surface of the chairs for the time specified by the manufacturer. After it expires, remove the old coating. For convenience, you can remove rough layers with a spatula. Sand the surface of the chairs with a fine-grained sandpaper.

Step 4... On the prepared uprights from the front side and on the uprights of the chairs from the front, mark with a marker in the places where you will drill the holes for the dowels. Before using the drill, be sure to check the correctness of the marks. Drill holes.

Step 5... Insert the dowels into the holes at the end of the uprights. Pre-grease them with wood glue.

Step 6... After the glue has dried, assemble the bench base. During assembly, in addition to wood glue, fasten the components with self-tapping screws. Sand all surfaces again.

Step 7... The seat of the bench will be a board fitted to the shape of the chairs. To do this, by trying on, apply the markings of the appropriate shape to the surface of the board and cut everything off with a jigsaw.

Step 8... If your bench seat, as in this case, consists of several boards, glue them together already fitted with wood glue. Clamp the structure with clamps and wait until the glue is completely dry.

Step 9... Glue the seat to the base of the bench. Send weights to the board and secure it with clamps.

Step 10... After the glue has completely dried, cover the surface of the seat with masking tape. Paint all other parts of the bench with wood paint.

Step 11... Remove the masking tape and stain the seat board.

Step 12... Paint the entire bench surface with wood varnish.

After the mat is dry, lay some pillows on the bench and enjoy your rest.

If you have several old chairs idle that seem to have served their purpose for a long time, this does not mean at all that it is time to take them to a landfill or send them to the oven. Think about where at home, in the country, in the yard there is not enough comfortable place to sit. There you will definitely need original hand-made benches. Show a little imagination, you will succeed.

Home bench

The set of kitchen chairs has fallen into disrepair. But just one little idea, and they became the basis for a charming bench. Comfortable spacious furniture made of chairs with your own hands will take its place in the hallway so that everyone who enters can sit down and change their shoes.

What you need to work

Before you start creating a bench, prepare everything you need:

Three old chairs. If you have a choice, take the best preserved ones.
3 or 2 boards. The amount depends on the width of the lumber. Put together, they become a seat.
2 handrails from an old chair. If not, select the appropriate planks.
Sandpaper.
Drill with drill.
Self-tapping screws.
Clamps.
Jigsaw.
Wood putty.
Dark paint on wood in a spray can.
Blue paint and roller.
Adhesive protective tape.

Operating procedure

Consider the chairs you choose. 2 at its best, place it on the sides of the future shop. Check connections. If they loosen during use, fasten them additionally with screws or self-tapping screws.
Remove the old soft seats from the chairs.
With a drill on self-tapping screws, install the railing from the old chairs to the outer chairs. If there are no such ready-made parts, make yourself a shape convenient for you.
Look carefully - it is necessary that the chairs standing next to each other are in close contact with the side surfaces of the front legs. If this does not happen, you can trim these places a little, then sand them with sandpaper.
Now that the adjacent legs are snug against one another, apply wood glue to one of each pair. Then secure them in pairs with clamps until the connection is solid.

Attention! So that there are no dents on the legs from the clamps, use small, even pieces of boards, plywood, and thick cardboard as spacers.

In the backs of the chairs there are metal rods of a metallic color. To paint them, first cover the wooden parts with protective adhesive tape. Then we spray dark paint on metal parts from a can.
You can start assembling the seat. Three planks cut to the length of the seat should be adjusted to fit. Then, small grooves for the armrests should be cut on the sides.
Using self-tapping screws, attach the two outer boards to the sides of the chair base.
To reinforce the structure, place small wooden inserts between the non-touching parts of the adjacent chairs, as shown in the photo below. Attach them with glue and on the self-tapping screws by screwing them in from the back.
Fill the bumps and holes on the face of the boards with putty.
After drying, sand the surface of the boards and the sides, slightly round their edges.
Using a roller, apply paint to the bench seat. Do not forget to pre-stick the protective tape on the parts of the backrest, railings and legs that are nearby.
After the paint has dried, we take sandpaper and slightly three legs and wooden parts of the back, so that the bench is evenly aged, acquires a somewhat rustic look.

The work has been completed. Once you've put a bench in your hallway, take care of the decor. Several original bright pillows will decorate the shop and make it more comfortable.

Bench for home

The bench is not the most necessary piece of furniture, but it is so comfortable and aesthetic that everyone likes it. This seat can be placed in the hallway, bedroom, balcony, garden, anywhere. This workshop is able to turn your dream into reality. Make a bench with old chairs. Moreover, the older the chairs you choose, the more interesting the result can be.

Materials and tools

Chairs (preferably with a beautiful curvature of the back) - 2 pcs.
Boards.
Plywood.
Thick foam rubber.
Decorative fabric.
Furniture stapler with staples.
Wood glue or liquid nails.
Drill, self-tapping screws.
White (color of your choice) paint, brush.
Hacksaw.

Description of work progress

For work, we need only a one-piece part - a back + rear legs. We carefully remove all other parts so as not to damage the necessary ones.
For the base of the bench, we take strong boards. We measure the desired width of the seat with a tape - cut out the corresponding parts.
The length of the bench seat must not exceed 2 times the width. We cut out the parts of the desired size.
Using glue and self-tapping screws, we assemble the frame. Grind its surface with sandpaper.
We install the frame in the place where the seats were located, on self-tapping screws and glue.
We assemble another frame for the lower shelf in the same way. We attach strips of smaller thickness to it. Sand rough areas with sandpaper. The lower structure will serve as a shelf and an additional stiffener for the entire structure.
We mount the shelf frame to the legs in the place where the crossbeams of the chairs were attached.
Carefully fill the grooves with self-tapping caps, irregularities, etc. with a putty. After the product has dried, we grind the surface.
You can start painting the finished base.
It remains to cut the seat out of plywood and glue thick foam rubber on it. After drying, use a furniture stapler to cover the seat with decorative fabric. The banquet is ready.

Original bench around the tree

Our bench will be a wonderful decoration for any garden. On a hot sunny day, she will allow everyone to relax in the shade under a tree at once. Everyone will get an equally comfortable place, because the shop itself is located in a circle.

Of course, such garden furniture can be purchased in a store, but it will cost many times more. To make a do-it-yourself bench from a chair no worse than one made by a master, you do not need to have professional work skills. It will be enough for you to get acquainted with the master class and prepare everything you need.

Preparation for work

To create a garden bench, you need to use:

6 completely identical old (or new) kitchen chairs.
Wooden planks 2.5 cm wide.
Sandpaper or sanding machine.
Drill with self-tapping screws.
Saw.
White paint, brush.
Roulette, pencil.

detailed instructions

Dismantle the seats on the prepared 6 chairs - they will not be needed in this project.
If necessary, sand the surfaces with sandpaper or a sander.
Paint the chairs white.
After the paint has dried, place the chairs in a circle with their backs facing inward. As you guessed, the bench will be outside. Given that the circle has 360 degrees, there are 60 degrees for each chair corner. Thus, we can try to calculate the size of the slats cut out for the seat. If it turns out a little inaccurate, you can correct the size.
Cut 6 strips of the same length in turn. We fasten them to the chairs with self-tapping screws so that the center of each plank coincides with the center of the chair. As a result, each seat should have 6 slats, each one longer than the previous one.
After the final adjustment of the length with sandpaper, sand the seats a little, remove any burrs and roughness.
Use a tape measure to measure the distance between edges 1 and 6 of the plank. Cut the part to this size.
Attaching it to the seat, outline the bevel with a pencil. Cut off the excess.
Using glue and self-tapping screws, install the planks as shown in the photo below.
Do the same with the rest of the future shop.
Sand the installed parts so that you cannot get hurt if you touch them.
Disassemble the structure again to paint the seat slats.

Congratulations! Your garden or yard bench is ready. It remains only to find a tree, the ground under which will be as flat as possible, otherwise your work may not collect. Take advantage of the advice - level the soil around the tree with mulch.