How to make door slopes with your own hands. Installing plastic slopes with your own hands: options and methods of installation What material is needed for door slopes

Recently, I learned in detail what door slopes are and what they are after the door has been installed. The fact is that if you order the installation of entrance or interior doors, the craftsmen often just do their job, without being puzzled about what you will do with the slopes.

And here there are two options, hire a team of finishers and pay them decent money for a trifle job, or make door slopes with your own hands. I chose the second option, and to be honest, I ran into certain difficulties.

I hope this article will help you avoid my mistakes and do everything efficiently and reliably.

Finishing door slopes

After the installation of interior doors was over, and I already wanted to relax, it turned out that there is such a thing as door slopes, and after installation they look very impartial. Leaving them like this would ruin the whole look of the house.

The question arose - how to close them up. Two options immediately came to mind:

Plaster and then paint.
Make door slopes from the laminate that was left after the renovation.

Both options are equally practical, but the installation of laminate flooring requires at least a small lathing, which is not always possible to install, especially if the opening is already narrow. In this case, plastering of door slopes is an ideal option, which does not require large financial costs and special skills in construction.

But first things first.

Plaster

Before proceeding to the description of the process of plastering the slopes on the door, you need to figure out why this method is better than others, and why you should give it preference. As you know, everything has its pros and cons. Plaster is no exception.

Advantages

There is no need to install a crate that hides the width of the opening, which is especially important for interior doors.
It is possible to close up the slopes on the door yourself, without the involvement of builders and, accordingly, additional costs.
Relatively low cost of all necessary materials and tools.
The whole process will only take a few hours, even if there is no relevant experience.

Well, now a little about the negative side of such door slopes.

Flaws

After plastering, door slopes require an additional coat of paint.
The aesthetic component leaves much to be desired.

Honestly, I have been looking for negative sides for a long time, but I haven’t found it, so we will stop at what we have and move on to the editing process.

Plastering slopes

Plastering door slopes, like any other repair, requires the preparation of materials and tools to facilitate this moment, we will list everything that we may need.

Tool:

Putty knife.
Construction level.
Grout with fine sandpaper.
Roller or brush for applying the primer.
Screwdriver, if installation is carried out under the "beacons".
Trowel for initial surface leveling.

Materials:

Plaster mix. It is advisable to take ready-made so as not to waste time on mixing cement with sand on your own.
"Lighthouses", two are enough for each slope.
Decorative corners that match the color of the room design.
Antibacterial primer-impregnation.

So, let's begin. First of all, it is necessary to thoroughly clean the slope surface from possible contamination: dust, dirt.

Important! An uncleaned surface adheres poorly to mixtures and after a few months the plaster will begin to fall off.

Next, we prime the surface with a roller or brush. Do not feel sorry for the primer, as they say - you can't spoil the porridge with butter. Moreover, cold bridges are always formed near the door, which can lead to the formation of condensation.

The primer must be allowed to dry well and only then proceed to the installation of "beacons". By the way, if you have skills in plastering, then you can do without them. Lighthouses are installed along the edges of the slopes and fixed to the wall using self-tapping screws or dowels.

After that, a plaster mixture is prepared, or rather, it is simply diluted with water in the proportions indicated on the package.

The plaster is applied with a trowel to the entire slope from bottom to top. And with the help of a trowel, which is leaned against two beacons, and the excess mixture is removed.

The leveled layer of plaster is left to dry completely, and only after that the surface is leveled with fine sandpaper.

Now it remains to make a decorative coating and set the corners. At this, the installation can be considered complete.

Laminate

It is somewhat more difficult to make slats for doors using laminate than just plastering. Installation takes place in two stages:

Manufacturing of lathing.
Installation of laminate.

The list of tools is even shorter than when working with plaster.

Screwdriver.
A hammer.
Adhesive for fixing decorative corners.

Materials:

Laminate.
Dowel.
The block is wooden.
Decorative corner.
Self-tapping screws for wood or drywall.

Advice! if the width of the slope does not exceed 20 cm, then the laminate can be installed lengthwise. If the panel is narrower in width than the slope, then the installation will have to be done horizontally from small segments.

Manufacturing of lathing

A wooden beam is best suited for these purposes, since it is thinner than a metal profile and the opening will not lose much in size. The timber must be treated with impregnations as well as the wall itself. This will keep the wood from rotting and will significantly extend the life of the finish.

The bar is attached to the wall with dowels with a step of about 50 cm, there should be two such guides, one on each side of the slope, but if the opening is very wide, then it may be necessary to install a third bar in the middle.

After the crate is ready, you can move on to the laminate.

Installation of laminate

Installation of laminate door slopes starts from the bottom up. The first segment is installed to the floor with a minimum gap of 2-3 mm, since the laminate does not have thermal deformation, this is quite enough. Further, the whole process is no different from floor mounting. The segments are connected to each other in a lock and snap into place.

Segments are attached to the crate with self-tapping screws to the very edge, subsequently the hats will be closed with decorative corners.

Advice! before attaching the laminate to the slope, it is advisable to pre-drill holes for self-tapping screws, since the edge of the laminate may crack or flatten.

After all the panels are fixed, you can put the corners. The easiest way is to fix them with glue, this is the simplest and most reliable way.

Conclusion

Having dealt with the question of how to close up the slopes after installing the entrance or interior doors, you can safely get down to work. Of course, there are many other ways to do this, but the option described in this article is the most inexpensive and, probably, the simplest.

As a rule, renovation in an apartment affects almost everything. It may also include the replacement of windows and doors.
In order for the doors to look neat, it is necessary that the finishing of the slopes from the inside of the entrance door is made with high quality.

Since it is possible to maintain one and the same temperature regime inside the room, the decoration of the entrance doors from the inside can be done with any finishing material.
For this, they are very often used:

Plastic panels.
Siding.
Plaster.
Decorative rock.
Wooden lining.

Front door trim with plastic panels

At the moment, plastic panels are very popular. All this is due to their high technical characteristics.
They are quite easy to attach and give a neat look to any surface.
Plastic properties:

Practicality.
Durability.
Easy installation.
Easy to clean.
Moisture resistant.
Not subject to temperature changes.
Resistant to high temperatures.
Do not fade in direct sunlight.

But these are all the properties that plastic panels have. In order to fix them on the surface, it will not need to be pre-leveled, which cannot be said about the use of decorative stone in the decoration of doorways (see Beautiful decoration of doorways with decorative stone).

Installation of plastic panels on the inner slopes of the entrance door

To carry out the installation of PVC panels on the slopes of the entrance door, you will need some tools and additional materials:

Wooden bars.
Self-tapping screws for wood.
Screwdriver.
Plastic panels.
Internal plastic corners.
External plastic corners.
Sealant.
Construction stapler.
Starting guides.

For reference. Plastic is considered a versatile finishing material that can be used in any interior.

So:

Plastic is attached to the crate. Initially, it will be necessary to assess the surface, if there are significant irregularities on it, then they are eliminated with a spatula or emery paper to ensure that the lathing is evenly attached to the surface.
The lathing for the installation of plastic panels is made of wooden blocks. Each element of it is fastened to the other with self-tapping screws and a screwdriver.

After the entrance doors have been installed in the apartment or house, ensuring the safety of the home, finishing work must be done. Outside, the entrance doors are ennobled with platbands, and if there is damage to the wall, then they are sealed with mortar. From the inside, everything must be done beautifully, and slopes are made to hide the irregularities. You can make them on your own, there is nothing difficult about it. It is necessary to choose the material, and then carry out all the work in accordance with the developed technologies.

Features of the device of the slopes of the entrance doors

If the doors are installed by professionals, then finishing the slopes is not their responsibility. You either have to pay extra for such work or do it yourself. If you understand the sequence of finishing, you can handle it without any problems.

The slopes of the entrance doors not only allow you to give a beautiful and complete look to the entrance to an apartment or house, but also hide the attachment points of the door frame, thus increasing the protection against burglary. In addition, correctly executed slopes help to insulate the entrance doors and increase their sound insulation characteristics.

Even the most expensive and beautiful doors will look unsightly if there are no slopes at all, or they are not neatly executed. When designing this element, it is imperative to take into account both the material of the door leaf and frame, and the design of the corridor. Slopes should harmoniously fit into the interior of the room, therefore, special attention should be paid to the choice of material for their manufacture.

Door slopes are:

outdoor. The front door is almost always mounted flush with the wall surface. For finishing external slopes, it is enough to install platbands, and if there is slight damage to the wall, then they are sealed with mortar, then the wall is covered with finishing material;
Outer slopes are usually covered with a casing
internal. Since these elements are located inside the apartment and are constantly in sight, a wide variety of materials can be used for their decoration. Internal slopes should be in harmony not only with the material of the canvas, but also with the entire furnishings in the room.
Different materials can be used to decorate internal slopes, the main thing is that they are in harmony with the interior of the entrance area

For the slopes of the entrance doors, you can use:

plastering. This is a cheap and reliable way, but you need to have certain skills to cope with it. First, you need to properly prepare the solution, and then evenly distribute it over the wall surface around the door frame;
panels fixed with glue. The walls are carefully leveled, special glue is applied to them, after which the finishing panels are glued. They can be from different materials, but the principle of the work is the same;
panels installed on the frame. This finish allows you to cover uneven walls. The frame is made of metal profiles or wooden bars, fastened to the wall and panels are already installed on it. Inside, you can hide wires and other communications, install lighting fixtures or lay insulating material.

What materials are slopes made of

There are no ideal materials, they all have their advantages and disadvantages, and the choice depends only on the financial capabilities and taste preferences of the owner of the house or apartment. To do it correctly, you first need to familiarize yourself with the characteristics and features of all used slope finishing options:

Drywall. This is a popular but time consuming method. First, the sheets are attached to the wall, and then putty and covered with finishing material. The result is a perfectly flat surface that can be painted in the desired color. Among the shortcomings, it should be noted that over time, the paint will smear, and if the wallpaper is glued, then they can tear.
Using drywall for finishing slopes is a popular but rather time consuming option.
Regular plaster. This type of finish requires special skills in order to obtain a beautiful and even surface. After plastering the opening, it will also need to be painted or pasted over with wallpaper. The main advantage of this option is its low cost. Cons - the finish coat can be damaged over time, and a lot of dirt and debris forms during work.
After plastering, the slopes must be finished with finishing material
Decorative plaster. This is a modern look of the previous material, it is applied to a previously plastered surface. You can choose textured plaster or with colored chips. Such a coating has a long service life and a beautiful appearance. Its disadvantage is the high cost, as well as the fact that the work is rather dirty and time consuming and also requires special skills.
Decorative plaster has a long service life and a beautiful appearance
MDF panels. This is the easiest and most affordable way. To install MDF panels, simple tools are required, and even a novice master can cope with such a task.
Decorating slopes with MDF panels is simple and quick
Laminate. Laminate, like MDF panels, is easy to install. This is a cheap and affordable material, but the slopes from it will not look very presentable and will not be suitable for expensive apartments.
Laminate is not suitable for finishing the slopes of entrance doors in apartments with an expensive interior
Natural wood. This is an expensive and environmentally friendly material, but it is not difficult to fix it. This solution is suitable when the hallway is decorated in the appropriate style. The wooden surface must be periodically treated with special compounds that protect against moisture and decay.
Natural wood is suitable when the hallway is decorated in the appropriate style
Chipboard panels. This material has a low cost, but its service life will also be small. Chipboard is afraid of moisture and at high humidity begins to exfoliate.
Chipboard panels are afraid of high humidity
Dobory - ready-made special elements that are used for finishing the slopes of both entrance and interior doors. You can choose a material that will exactly match the door frame. The cost of completions is higher than that of panels or laminate, but their appearance is also more attractive.
PVC panels. They will be cheap, any home master will be able to cope with the installation work. Plastic is not afraid of moisture, has a long service life, and is easy to care for. The disadvantage of PVC panels is their not very presentable appearance.
Even a beginner can trim the slopes with the help of PVC panels.
Natural or artificial stone. Beautiful slopes can be created from stone, which, moreover, will have a long service life and high wear resistance. The disadvantage is that laying the stone requires a certain skill and a lot of time. If the slopes are finished with natural or artificial stone, then the adjacent walls should be plastered, since wallpaper or panels are not suitable in this case.
Artificial stone slopes have a beautiful appearance and high wear resistance
Mosaic and tiles. It is also a durable and durable material, but usually tiles are used in the kitchen, bathroom or toilet and many people do not perceive it on the slopes of the entrance doors. In addition, laying tiles, and even more so mosaics, takes a long time and requires special skills.
Not all people perceive tile slopes, since this material is usually used in the kitchen and in the bathroom.

Required tools and materials

In order to independently finish the door slopes, you first need to decide on the method of their installation. Depending on whether the plastering of the surface will be carried out or laying the material in a frame and frameless way, you may need:

The main stages of finishing the slopes of the front door

After you have decided on the method of finishing the slopes of the entrance doors and purchased the necessary materials and tools, you can proceed with the installation. Almost any home craftsman can do this work with his own hands; it is enough to perform all the stages in accordance with the developed technologies.

Preparatory work

Although different materials are used for finishing the slopes, the preparatory work in all cases is carried out in the same way:

Plastering

It is best to plaster the slopes of the entrance doors at the stage of apartment renovation, since a lot of dirt is formed during the work.

Surface priming. This step is necessary to ensure good adhesion of the mortar.
Primer increases the adhesion of materials
Installation of beacons. Beacons are installed using the building level. They allow you to mark the thickness of the applied plaster and help to distribute it evenly.
Lighthouses help to apply the plaster evenly
Corner installation. With the help of a solution, a corner is fixed at the junction of the wall and the slope.
The corner protects the junction of the wall and the slope
Fastening the painting net. It is necessary to increase the strength of the plaster layer.
Application of the solution. A solution is thrown over the lighthouses, after which it is distributed by the rule.
After applying the solution, it is leveled with the rule
Priming the plastered surface.
Finishing putty application.
Grouting the surface. The coating is processed with a fine grater so that it turns out to be perfectly even.
For grouting, use a special tool and a mesh
Painting. Water-based paint is usually used, as it dries quickly and is practically odorless.
To paint the slopes, use water-based paint

Video: plaster door slopes

Adhesive finish

Various materials can be glued to the slopes, including drywall, laminate, MDF or chipboard panels. This method can be used when the walls do not have serious defects. Minor deviations from the level can be corrected by applying a layer of plaster, the thickness of which should not be more than 8–10 mm.

The process of gluing panels installation consists of the following stages:

Base primer. For this, special compositions are used that allow increasing the adhesion of materials.
Measurement of slopes. Using measuring tools, the dimensions of the slopes are measured and transferred to the material used for finishing (drywall, chipboard, MDF, sandwich panels). Drywall can be installed both vertically and horizontally, since then all the seams will be putty. It is better to install MDF and chipboard panels with one canvas so that there are no joints.
Slope measurements are transferred to the material used
Glue application. This is done in a square-nesting way every 15–20 cm. It is not necessary to completely cover the material with glue. A film should appear on the surface of the glue, for this you need to wait a few minutes.
The glue is applied in a square-nesting manner.
Fastening panels. They are laid starting from the upper edge and pressed with force on those places under which the glue is located. The panels can be attached to liquid nails, polyurethane glue or polyurethane foam.
The panels are installed in place and well pressed against the supporting surface
Finishing finish. If drywall was used, then after its installation it is necessary to apply a topcoat. Laminate or MDF boards do not require additional finishing.

Video: adhesive trim of the slope

Frame method for finishing slopes

In order to exclude the possibility of surface deformation after plastering or installing heavy MDF sheets, a frame method of finishing slopes is used. To create a frame, both metal profiles and wooden blocks treated with an antiseptic can be used.

Work order:

The surface is treated with an antiseptic primer.
Vertical profiles are mounted. The extreme profile is set in level and fixed with dowels. The second post is set in accordance with the first and also fixed.
To increase the rigidity of the frame, transverse profiles are installed
Install wiring and insulation. If you plan to install an electric lock, a cable is laid inside the frame to connect it. Insulation (mineral wool or foam) is also placed in the cells.
Carry out interior decoration. If these are MDF boards or laminate, then finishing is not needed. Plasterboard is putty and painted or pasted over with wallpaper.
Drywall or other finishing material is attached to the finished frame

Decorating slopes with artificial stone

To decorate the slopes of the entrance doors in an original way, artificial stone or clinker tiles are often used. In this case, the rule is followed: there is more stone at the bottom, less at the top. This solution allows you to smooth the transition to other finishing materials, and the irregularities give the slopes a more natural look.

Sequence of work:

Video: creating the slopes of the front door with your own hands

Whatever chic door you put for yourself, but without a decent frame, it will look, to put it mildly, unpresentable. Finishing the slopes of the front door is just as important as installing it. But often a person has no idea how to decorate the slopes of the front door. Let's talk about how to refine a doorway, discuss the pros and cons of the most popular materials.

Often it is the slopes that are responsible for the presentable appearance of the doorway.

Before you arrange a doorway, let's figure out what the openings of entrance doors are like.

The classic regular rectangle is the standard, most common option. As strange as it may sound, deciding how to decorate the doorway of the front door with classic shapes is the most difficult thing. You can decorate with anything, but the problem lies in the large selection of materials, which can be difficult to decide on. The main plus is that finishing the doorways with your own rectangular shape will not cause much difficulty.
The arch looks more impressive, but finishing the door slopes after installing the arch-type entrance door is technologically more difficult. Plus, not all materials will work. Except for the branded linings that come with the door, all that remains is plaster, drywall and elastic polyurethane slopes.

Arched openings look more impressive.

If the arched design of the doorways does not give you peace of mind, it is not necessary to equip a real arch: it is much easier to install a decorative overlay in the form of an arch in the lintel area (upper crossbar). This can be done both from the inside and outside, but the door itself and the slopes will be rectangular.

The decorative overlay will help to arrange the doors in the form of an arch.

How and what can you decorate the slopes of the main door of your home

If you are faced with the task of how to finish the slopes of the front door, you can familiarize yourself with step-by-step instructions in and on the video in this article, and we will try to make out to the smallest detail all the pros and cons, which are often forgotten to be mentioned in brochures.

Option number 1. Good old plaster

Decorating doorways with cement plaster is deservedly considered the patriarch of the trend. Such finishing of door slopes appeared along with the doors themselves.

A well-plastered and finished slope will last for more than a dozen years, it is not afraid of temperature extremes, humidity or cold. Plaster will fill in all voids and irregularities. To spoil such a slope, you need to pound on it with a hammer. If you are not going to influence your doors so radically, then you can be calm about the rest. To refresh the surroundings, the plastered slope can be repainted, wallpaper can be pasted on it, or it can be revetted with the now fashionable reflective film with a 3D effect: a smooth and durable surface will withstand everything.

But the plaster has a downside. Of all the finishing methods, plastering slopes is the most time-consuming and messy process.

Plastering the slopes of entrance doors is not easy.

Of course, if you install the lighthouses correctly, buy good plaster mixes and a high-quality tool, then things will go much faster. Although believe me, if you have never plastered doorways with your own hands, this kind of design is not for you. In addition, plaster is, in fact, a stone, only artificial, and you should not expect any serious insulation from such a finish.

There is one more professional nuance. Even on a well-leveled slope, you can only glue the wallpaper, and then after two layers of primer. For high-quality staining, one plaster is not enough: the surface will still have to be additionally putty and sanded, and putty and grinding will take no less time, effort and money than plaster.

Plastered doorways look simple yet elegant.

By the way, if you plan to trim the slope with natural or artificial stone, then the plaster will be the best and most reliable base, you do not need to putty it.

Option number 2. Plasterboard slopes

The next in terms of reliability is the finishing of the doorway of the entrance door with plasterboard sheets. Such cladding is also called dry plaster.

Drywall attracts with speed and relative ease of installation, plus, if necessary, door jambs can be closed almost completely. If we conditionally break down all the work, then, in short, finishing the entrance door opening with sheets of moisture-resistant drywall consists of 5 stages:

According to the rules, before finishing the opening of the front door, the surface must be cleaned of debris and covered with soil. But if the base is solid, for example, a brick wall, then it is enough to brush off the dust and walk with a solution of copper sulfate so that the fungus does not start.
Next, we install a frame made of metal profiles. There are wall and ceiling profiles, so for the slopes it is better to take the ceiling (UD / CD). If a large space overlaps, then a one-piece frame is mounted, and when there is little space, only the extreme vertical guides are placed.

It is better to take gypsum plasterboard (12.5 mm), and the sheets must be moisture resistant. If an arch is formed, then there is an arched drywall (7.5 mm) for it. The sheets are attached to the frame with self-tapping screws, and they are glued to the wall with tile glue or a similar building mixture.
When the structure is assembled, it needs to be putty. Remember - nothing is glued to the "bare" sheets, is not painted or attached.
The last step is the decor of the doorway. It all depends on taste, skill and financial capabilities. The easiest way is to paste over the slopes with wallpaper. They do not need to be carefully sanded under them. Next comes painting, but before it you will have to sand the slope well. Tiles or stones are more expensive, but they can be glued quickly and easily.

A hollow plasterboard slope has another indisputable advantage: it can be filled with insulation, thereby increasing heat and sound insulation. In this case, it is better to take polystyrene as a heater. There is an option to blow in the polyurethane foam, but you need to act carefully: it can squeeze out the sheet when expanding. It is advisable not to use mineral or any other wool for insulating the passages of the entrance doors: it will become damp from condensation and become useless.

Many reproach drywall that it allegedly breaks easily, but believe me, if you mount a good frame with a gap between the profiles of no more than 200 mm, and when installing on glue you will not regret the glue, then you can not worry about the strength of the slope.

Option number 3. MDF

Decorating the doorposts of the MDF entrance door with slabs at the moment is considered perhaps the most common. This is a rather tough and at the same time beautiful material; such panels behave well under temperature extremes and in conditions of high humidity.

When choosing MDF panels, there is a small nuance: for finishing the entrance door from the inside, you can take any sheets, but under the outer slopes, especially if the doors go directly to the street, you should buy only moisture-resistant ones (the back of them has a greenish tint), otherwise after a year all beauty will go in bubbles.

In this case, we are only interested in laminated panels, it makes no sense to take ordinary panels and then paint them separately. The line also includes panels covered with natural wood veneer. The price for them is about half as high as for laminated ones, but on the other hand, such slopes are practically indistinguishable from expensive wood.

A backlit slope made of veneered MDF is not only beautiful, but also comfortable.

As for self-assembly, it is not a problem to buy and install accessories, platbands, fixing corners and other things. You are essentially dealing with a constructor. First, a frame of wooden bars is constructed along the perimeter of the opening, and panels are already attached to it.

From a relatively expensive tool, you will need a miter saw or at least a jigsaw, as well as a drill and screwdriver. A hammer, tape measure and so on are usually in the arsenal of any home craftsman.

The downside of MDF slopes is only the price of the material itself. Only natural wood of elite species is more expensive than such cladding, by the way, it is mounted in the same way, but it is better not to tackle it yourself: the risk of spoiling is too great.

Equipping a door slope from MDF is not as difficult as it seems.

Option number 4. Lining

The price of a good wooden lining is approximately equal to the cost of MDF, but in this case you get slopes made of natural wood. This design of the doorway looks pretty solid, but there are nuances.

Any lining is mounted on a wooden crate, which means that you should have enough space for such a crate. Accordingly, it is problematic to make small slopes from the lining.

Natural wood is a good material, but rather moody. In extreme conditions of entrance doors, the tree must be covered with antiseptics, fire retardants and other protective compounds.

Previously, everyone varnished the lining, now design experts do not recommend varnish. The fact is that most people associate lacquered lining with balconies and garages, and the front door is still the face of the home. It is best to buy an oil-wax impregnation and apply it. The result is pleasing: fast, beautiful and inexpensive.

Option No. 5. PVC

Slopes from finishing PVC panels can be mounted within 1 day, plus the price of this material is available to almost everyone, but decorating a doorway with plastic has a number of negative aspects.

Plastic PVC slopes are installed quickly and easily.

You can break a hollow thin panel by simply leaning against it. As practice has shown, even the highest-quality plastic panels on a good crate in the area of \ u200b \ u200bthe entrance doors last no more than two to three years.

Under the plastic, you need a wooden or metal crate. Theoretically, such a panel can be glued to a plastered slope with liquid nails, but if you have a good plastered slope, then why do you need plastic then.

In addition, according to fire regulations, it is highly undesirable to mount plastic in the area of \ u200b \ u200bthe entrance. In the event of a fire, it will actively melt and emit a suffocating pungent smoke, thereby blocking the exit.

Although, on the other hand, plastic is the best choice as a temporary solution to the problem. And when you have enough funds, you can quickly dismantle it and install solid slopes from high-quality MDF on the same crate.

PVC panels have a fairly wide range of decor.

Option number 6. Decorative polyurethane overlays

If you dream of seeing your doors decorated with luxurious stucco moldings, we recommend paying attention to decorative polyurethane overlays. Visually, such a finish cannot be distinguished from good stucco molding, and the performance of such slopes is an order of magnitude higher. The only problem is that the price for such jewelry is quite serious, plus you can't stick an overlay on a curved base. In other words, you will first need to level the slope with plaster or drywall, and then glue the polyurethane beauty on it.

If the slopes are decorated with luxurious stucco molding, this indicates the good taste and status of the owner.

A few words about the decorative finishing of door slopes

The finishing decorative finish is applied only to a solid prepared base, respectively, we can only choose between plaster and drywall.

Most often, people choose simple staining. The quality of modern paints is such that they can retain their original appearance for a long time and in any weather conditions, plus, if you get tired of the color, you can always repaint.
The next in the ranking of the finishing of door slopes is decorative tiles. Tiles are not suitable for entrance doors, so it is better to give preference to clinker tiles. If funds allow, then you can revet the slopes with artificial stone, by and large it is the same tile, only made of stone dust and polymers.
Natural stone tops the top three. The pleasure is far from cheap, in addition, it is better not to take it with your own hands and without preparation. Natural stone is a heavy and difficult material to work with.

A quality artificial stone is visually no different from a natural one.

Conclusion

In conclusion, we would like to note that it is better for home-made ones to dwell on materials designed for crate. These are MDF, wood and PVC. If you are confident in yourself, then you can swing at drywall. But we recommend leaving the plastering of slopes to professionals.

Door slopes made of MDF are one of the most affordable for independent arrangement.

Even the most luxurious front door will look unpresentable if the slopes around it are sloppy. They are designed to serve as a beautiful frame, complement and highlight the main element -. To decide how to trim the slopes of the entrance door, you need to pay attention to its style, design and color scheme. The slopes framing the entrance inside the apartment must correspond not only to the decorative parameters of the door, but also to the design of the hallway.

In addition to a purely decorative function, these elements around should also serve as additional effective insulation, since their plane covers the joints between the door frame and the wall.

How can you trim the slopes?

The finishing of the slopes in the running door can be made from different materials, or you can simply put the existing slopes in order.

1. If the door is reliable and strong, but not outstanding in design, you can simply level the slopes with plaster, reinforcing their corners. Such work is usually carried out both from the side of the entrance and in the hallway.

Slopes can be neatly finished with plaster

Plastered slopes will look quite neat - they can be painted in a color close to the shade of the door itself or to match the wallpaper in the hallway.

2. In the case when the walls of the house are thick enough, and the slopes are wide, you can use for finishing with such familiar material as drywall. It will make the walls warmer and reliably close the joints between the door frame and the wall, giving the slopes a neat look.

Drywall, if desired, can be pasted over with wallpaper or painted. The advantage of this material is that you do not have to painfully level the plaster using a rule and then clean the wall.

3. You can make slopes from natural wood, if it is suitable for finishing the door. Wood has always been popular and has never gone out of fashion, it goes well with almost any interior, and its tint can be easily changed with the help of modern or folk remedies.

The tree will reliably serve for many years, without changing its natural decorative properties. In extreme cases, it can be painted to match the color of the hallway.

4. An alternative to wood can be a laminated lining based on fiberboard.

Since the lining is produced in various colors and imitates the textured patterns of a wide variety of wood species, it can be matched to any design of the hallway. However, it is not recommended to trim the slopes on the outside of the door with this material, since it will not last long there.

5. Ready-made PVC panels can be another finishing option. They are produced in various widths and in a wide range of colors. The production and sale of such parts is carried out by specialized firms, in which there are masters who are engaged in installing panels.

One of the most successful solutions is carefully fitted PVC panels.

This finish looks respectable and aesthetically pleasing. PVC panels will last for a long time, but it is also better to install them from the side of the apartment, and from the side of the entrance use the first or second method described above for finishing.

If you are confident in your abilities, then the ready-made parts of the slopes can be installed on your own.

Another option for using polymers for finishing the inside of the door can be plastic lining. It is also easy to choose it to match the color of the walls of the hallway, since there is a wide range of this material on sale.

6. Sheathed slopes and chipboard panels - they are mainly used for very thick walls. However, it should be noted that at present this method of finishing is not very popular, since a large number of other materials have appeared that can easily replace these rather heavy panels in installation.

Nevertheless, if this material of the required dimensions was found at home, then it may well be used to decorate the door slopes from the side of the apartment.

It should be noted that there are other materials that can be used to tidy up the planes around the door, but the above options are the most popular.

Tools and building materials for finishing slopes

For finishing the slopes, you will need materials and tools that will help to carry out all the work neatly.

1. For plastering work you will need:

primer and finishing putty for surface preparation.
plaster mix or traditional cement mortar.
perforated metal corner for aligning corners.
a serpyanka mesh, a clerical knife and self-tapping screws will be needed if the slopes are made of drywall.
sandpaper coarse and fine-grained.
wide and medium spatula.
short rule for leveling the surface of slopes.
container for mixing the solution, a drill with a special mixing attachment
plumb line and level.

2. For the installation of panels made of different materials, it is necessary to prepare:

ready-made panels for installation on slopes or material for them.
decorative corners and platbands for closing panel joints.
timber with a section of 15 × 30 or 20 × 30 mm, if lining will be installed.
dowels for fixing panels or timber to the wall.
small nails and special holders for the lining.
hammer drill or hammer drill if the house has concrete walls.
self-tapping screws for fixing panels.
measuring instruments.
hacksaw or jigsaw, screwdriver, knife, hammer, etc.

Having prepared everything you need, you can proceed to surface preparation and installation.

Slope finishing technology in the running door

Each type of slope finishing work has its own characteristics:

The installation of many of the materials presented is carried out using the same technology.
Some of the finishing technologies are distinguished by their simplicity, and with the right approach to work, they can well be done independently.
Others can be used for independent use only if the homeowner has the necessary skills in working with building mixtures and tools.

All slope installation activities begin after the door is installed and all the gaps between the door jamb and the wall are sealed. In addition, all breakaway parts of the old pavement are removed from the slopes and crumbling areas are cleaned. When these works are carried out, they start finishing in the chosen way.

Plastering of slopes

If the decision is made to level and plaster the slopes, the process goes to following sequence:

First of all, the cleaned surface should be well primed, preferably in two layers, but the second time the primer is applied only after the first layer has dried.
Further, the evenness of the angles of the slopes is clarified. If deviations from the norm are determined, then this fact must be taken into account when installing reinforcing corners. They can align corners that have small deviations from the vertical.

Then it is necessary to set perforated corners at the corners of the slopes along the plumb line and level. They are best planted on a ready-to-use finishing putty. It is applied with a spatula to the corners of the slopes - the composition will serve for gluing the corner and makes it possible to align it to a perfectly vertical or horizontal position. Excess mortar that will show through the holes in the corner must be immediately removed with a spatula. Having brought the corners to the ideal, the solution under the corners is left to dry.
If the surface of the slope is uneven, then before installing the perforated corners on the corners, you can set the direction from the door jamb by fixing a narrow strip of drywall 8-10 mm wide along it. This material is fixed to the wall with a putty. If it is on a gypsum base, then it solidifies quickly enough.
The edge of the plasterboard strip and the installed reinforcing corner will become points that need to be connected with a putty solution and leveled with plaster.
Further, after drying the elements correcting the wall, the putty is diluted in the proportions indicated on the package to a pasty consistency.

Using a trowel, throw the finished composition onto the wall, starting from the floor. Having sketched the required amount, about a meter in height, the putty is leveled with a rule. In this case, the beacons are a perforated corner fixed at the corner and a strip of drywall fixed along the door frame.

Then the solution is poured onto the next section and is also leveled, and so on to the top of the opening.
It will be more difficult to putty the ceiling part of the opening. Putty is applied to it with a wide spatula and leveled with a short rule. Then putty is applied to the wall above the correct opening, and it covers the upper part of the metal corner.

The slopes treated with the putty are left to dry. The time of this process depends on the thickness of the layer and the composition of the putty.
After this layer has dried, you need to check the quality of the surface, remove possible minor imperfections - chip or clean the incoming irregularities. Then the slopes need to be removed with a finishing putty to perfect evenness.
Further, after the filler layer has dried, it is covered with a primer.

The resulting surface can be painted, wallpapered or finished with decorative plaster.

Video: finishing the door slopes with plaster mixes

Prices for popular types of putty

Putties

Plasterboard finishing of door slopes

It is easier and more pleasant to work with drywall than with the removal of slopes using plaster. Nevertheless, in this case, you still have to work with the finishing putty, which will play the role of an adhesive composition for drywall sheets, but it is still better to use a special gypsum-based glue for this purpose, produced specifically for working with gypsum plasterboard.

If space is limited, then drywall is perfect for decorating slopes. This process is carried out in the following sequence:

To begin with, all surfaces of the slopes are measured separately.
The obtained data is transferred to the sheets of gypsum fiber board, and elements are cut out from them, which will be fixed to the walls.

Installation of finished parts starts from the ceiling of the opening. To do this, glue is applied to the drywall blank in several slides, and then this element is firmly pressed against the installation site and fixed in this position by pre-prepared supports.

Then the sloping walls are finished with details cut out from the gypsum fiber board. Glue is also placed on the prepared element in small slides, and the sheet is pressed against the wall and measured according to the level. Plasterboard sheets can be fixed to the wall with hammer-in dowels, making through holes for them, but not too wide, using an electric drill or perforator.

On the corners of the slopes, in the same way as when plastering, metal perforated corners are fixed with putty.
Then all joints are coated with putty, leveled, and after drying, they are thoroughly cleaned.
Further, the entire surface of the slope is covered with a primer.
To achieve a perfect surface, a thin (no more than 1 mm) layer of finishing putty is applied. It will completely hide all irregularities, joints and holes from the dowels.
After the layer of putty has completely solidified and, if necessary, sanding with fine-grained sandpaper, you can start decorating the slopes. They can be painted, pasted over or covered with decorative plaster.

Fasten drywall and otherwise, in the event that you need to level the surface, covering a significant thickness from the wall.

Combined fastening of plasterboard parts - on glue and on guides

To do this, bars of the desired section or metal profiles, corners or U-shaped shapes are fixed to the slope surface, thus creating a crate that will help level the wall, giving it the required direction. This mounting method has the advantage that additional insulation material can be placed between the guides fixed to the wall.

This whole structure is then covered with drywall, which is screwed to the bars with self-tapping screws. Further, the process proceeds in the same way as in the first option.

Video: finishing of door slopes with plasterboard - ceiling part

Video: continuation of the video about finishing the slopes with plasterboard

Decorating slopes with panels or clapboard

For finishing slopes with materials that are produced in the form of rigid panels - fiberboard, lining of various types, MDF and others, a similar technology for attaching them to the wall is used. This method is attractive in that with the help of panels it is possible to align corners that have large deviations from the norm.

Installation of such materials is carried out as follows:

The primed surfaces of the slopes are marked out for fixing bars or a metal profile on them, on which the finishing material will be fixed in the future. These auxiliary elements are located at a distance of 30-40 cm from each other if they are installed across the slope. In this case, if lining is used for decoration, it will be mounted parallel to the door frame. If it is necessary for the panels to be located across the surface, then the bar is fixed along the jamb and closer to the angle of the slope. For a wide surface, not two, but three or even four bars are used.

You can carry out the lathing as shown in the picture - this option is called for fixing the lining parallel to the door.
After installing the lathing, it is recommended to lay an insulation material between the bars - it can be mineral wool, foam or one of the other modern insulation materials.
Further, the installation of the selected facing material is carried out along the crate. One-piece flat panels are installed end-to-end with each other, the lining is connected with a groove-tenon fastening.

The plastic and laminated lining is fixed to the bars from the side of the slotted part of the lock using special metal holders, which, with their protrusions, are put on the bottom shelf of the slot and are attached with a guide with small nails or self-tapping screws.

Panels, large in area, are screwed to the crate with self-tapping screws, the heads of which must be "drowned" 1.5-2 mm into the thickness of the material. These holes are later sealed with wood putty with the addition of a dye of the appropriate shade.
Having finished with the installation of the panels, the appearance of the slopes must be refined with corners matched to the color of the cladding. The corners are glued at the outer vertical and horizontal corners and at the junction of the door frame and finishing material.

Features of vinyl slopes

The most modern way to transform slopes is to install vinyl panels. They can be purchased from specialized firms that are engaged in both the manufacture and installation of this finishing material. If it has a non-standard shape of the slopes, then they are made to order, after measuring the parameters. The surface of the slopes can imitate many natural materials, so they can be matched literally to any interior of the hallway and the color of the entrance door.

The most important advantages of ready-made panels in their installation are its speed and the absence of a large amount of debris and dirt during operation. It is impossible not to say about the aesthetic qualities of this finish - it is cut exactly to the size of the slopes and has no joints or seams on the planes. The only connections that cannot be abandoned are the joints of the horizontal and vertical planes. The material looks very presentable and neat.

For the installation of such slopes, universal glue is used, which has the properties of firmly connecting various materials to each other, such as wood and concrete, brick and chipboard, vinyl and plaster surface - almost everything used in construction and decoration. In addition, they are often attached to polyurethane foam.

These adhesives are applied to the inner surface of the finishing panels, and they are pressed against the slopes around the door. In this case, there is no need to drill holes in the facing material and walls, which can also be called an indisputable advantage of such a technology of installation work.

By doing the work in stages and adhering to the technology, it is quite possible to independently complete the work on finishing the door slopes. Even without the opportunity to purchase finishing material, many apartment owners use what is at hand, for example, chipboard panels from used furniture. But still the most affordable and easy-to-install (except for ready-made vinyl panels) is the option using. It opens up wide possibilities for finishing decoration in almost any existing way.