Homemade cars with a jetty engine. Unusual homemade from chainsaws: a new look at the old tool

The versatility of gasoline chain saws is proved not only by their multitasking and functionality, but also abundantly useful homemakes, which folk craftsmen learned to do their own hands. They save funds for the purchase of expensive factory devices, in which most people have no money banal. But, as they say, a gol on the fiction of Ortre. Therefore, speaking of chainsaws, many represent not only wooded or fruit garden trimming, but also winches, ice womb, boat motors, grinders, panels that technically competent masters have learned to adapt from all the favorite gasoline tool.

No less attention deserved means of movement - bicycles, mopeds, karts, quad bikes and much more, which can be collected from the use of a chain saw with a gasoline engine. About how and from what to recreate them and surprise the surrounding incredible motorized design, we will talk in this article.

Motorbike made of chainsaws with their own hands

Not every lucky bicycle owner is delighted with the need to twist the pedals and spend their strength. More convenient and less expensive in force is a motorized bike.

A bicycle with a motor from chainsaws with their own hands is not so difficult, as it seems at first glance. To do this, you will need:

bicycle;
saw with a power of a benzomotor at least 2000 W - from this indicator will depend on whether it can move from the spot. As practice shows, engine power in 2 hp It is enough for the motorbike to develop speed up to 40 km / h;
tank for the future fuel tank;
cable from the old bike;
handle to have the ability to adjust the throttle;
bolt ties, nuts and other minor consumables for creating fixtures;
connecting elements to create a wheel message with the engine.

The process of how to put the engine from chainsaws on the bike, looks like this:

we aggregate the driving shaft - remove the rear wheel tire and put the tire with a diameter of up to 2.5 cm. This snap will help take the rotation of the motor, and like a reducer, reduce the number of revolutions;
electric welding welded a stand from the corners - it will help to install the engine from chainsaws;
alteration of clutch - you can use the centrifugal from the factory saw by connecting it to the wheel;
adapt the benzobak - it can accommodate next to the engine, or on the frame;
fix the wire from the incendiary motor system on one of the bike handles;
adjust the gas cable from the carburetor to the gas handle to control the throttle valve is simple and rapid;
we equip the motorbike to means of protection: mirrors, lantern, and move to the test of a self-made bike from chainsaws.

As you can see, the motor from the chainsaws to put on the bike is not so difficult.

How to make a moped from chainsaws?

The dream of the majority of our fellow citizens was and remains a moped. It develops higher speed and has a structure, perfectly higher than the player described. Buy a ready moped - the pleasure is not cheap. We will tell you how to make it from girlfriend.

To do this, you will need:

motor from a good powerful saw (in our version is a "friendship" model);
2 wheels from the old bike;
tube with a diameter of 2 cm (metallic);
cable;
bicycle stars; as well as forks;
old motorcycle spare parts are ready-made fuel tank, headlight, if desired and the seat, although it can be done with your own hands;
steering part;
gas lever.

The process of creating a moped looks like this:

cook the frame to which connect the wheels from the bike, forks, as well as a benzobac and a lantern;
adjust the motor - the installation composition will depend on the frame configuration;

screw the gas tank and battery;
we check that the newly installed elements do not hang out;
we make a chain transmission - it will allow the wheels to take the torque of the motor and move. You can take a belt instead of a chain pulley. But it is impossible to forget that it will be noticeably higher;
we establish the ignition system - connect the battery and the brake lever with it;
separate the exhaust pipe.

The assembly process is completed: you can proceed to testing the moped.

Karting from chainsaws with your own hands: Step-by-step assembly

Karting is a modern vehicle, which in a short period of time can overcome a considerable distance. Exclusive cards - the dream of every car enthusiast. It is not necessary to participate in racing with it: it can be easily moved to rough terrain on it, in rural roads, and indeed everywhere, where the more overall car does not pass.

Among the possible options for equipping, homemade kartins from chainsaws were greatly popular - no less powerful and productive than their serial analogues. Consider stages.

Preparatory stage

It begins with the compilation of detailed drawing and design. We suggest familiarizing yourself with the Ready Drawing, which will save time on the designs;

The proposed overall dimensions are suitable for a man of medium height. For adolescents and high people, the design should be driven by their individual parameters. For adolescents, you can use another diagram below.

We collect the base of the constructive

This is a chassis, the manufacture of which will require:

square pipes (up to 10 m);
steel pipes;
thick steel plate;
snaps for blockage bottom;
chairs.

The process looks like this:

pipes are cut on the proposed scheme and welded with electric welding.

This is what should happen after welding;

the front axle is equipped with plugs;
the rear axle is aggregated - it is welded to the frame itself in such a way that its rotation was ensured;
from metal or durable wood according to the drawing, the bottom is cut and adjusted to the frame;
seat - In this case, you can not mess and take ready from the old card or machine.

Karting equipment Motor

remove the motor with chainsaws;

we make the database for the motor - from steel plate and corner. His pulley must coincide with the last framework;
screwing the pulley;
we take 2 metal rods that bend at right angles - it will be the drive steering wheel;

separate the brakes - it is desirable that braking applied to all 4 wheels. Do not forget about the brake pedal: Hands to harm on the brake will be very uncomfortable;

eating karting wheels - Wheels with a small diameter from the old racing car;
i combine ignition - connect it with a throttle valve and a gas handle;
control of reliability Assembly and testing of the finished unit.

Karting is a luxury for an ordinary person, but with the help of submitted means you can create its budget version - kart with the engine from chainsaws.

No less well-known homemade, which was learned to make domestic "couliabs". For her reconstruction, we will need:

scooter, designed for the weight of the person who will control them. It is desirable that he originally had a manual braking system. The pneumatic wheelbase of the scooter should be durable;
the chainsaw with which the engine is removed - medium and high-power models are suitable.

The scooter assembly process looks simplified compared to previous homemakes:

to begin with, we remove the propulsion base and fix it in the back of the scooter frame. We observe the motor and wheeled stars coincide;
we will adjust the manual accelerator with the ignition of the Motorciles - so the operator will be able to monitor the process of movement;
if necessary, equip a brake pedal scooter, but in most cases the lever for manual control of the scooter is enough for its full-fledged work.
testing a chainsaw scooter - in case of service, a new motorized device is ready and can be operated.

Homemade children's quad bike from chainsaws

The last homemade, which we will consider, will be devoted to quad bikes. In fact, for the assembly of the Quadrocycle, similar materials are needed, as well as for karting or tricycle:

engine from old powerful and working chainsaws;
reducer - Increases the motor thrust and assumes his working turnover;
quadrocycle frame - it should be stronger and stable;
the driver's seat is good if there is an old armchair from the moped: a teenager will be more convenient in it than in the cumbersome car;
wheels with a gross protector, diameter at least 34-35 cm each. This will improve the permeability of the Quadrocycle and make an analogue of the SUV.

If desired, the prefabricated constructive of the Quadrocycle can be brought to perfection by shock absorbers: the maneuverability of the Quadrocycle will increase, and the work move will become more smooth.

Homemade vehicles - a cheap thing, but not always reliable. You can use them only with strict compliance with all safety regulations.

Engine Any chainsaws can be used to make a simple technique: from the mower, to the helicopter. It all depends on the tasks and goals of the master. But not everyone understands why the engine from the saw of friendship 4. Not everyone is understandable to the end, how and what can be done with your own hands. This article is written to help the masters and eliminate this gap.

We call a number of arguments, why it is worth using a chainsaw friendship for reworking:

popularity - Chainsaw was very popular during the USSR, because Others saw simply was not, except the Urals.
cost - today in the secondary market, the price depending on the state varies from 1000 to 2000 rubles.
power - saw refers to the category of professional, designed for rolls of trees, so it is well suited for such homemade such as a mower, a helicopter, a sawmaker, all-terrain vehicle, a motorcycle and others.

What you need to work

To make your own hands, homemade sunglasses. Friendship is needed a set of tool of a novice master, desire and idea. The main tools are necessary for work, it is a Bulgarian and a welding machine. You already have a desire, otherwise you would not be on this page. The idea itself for alteration chainsaw friendship in any unit you will find in this article.

In the article we offer only an idea, without step-by-step instructions for action. Otherwise, the article would be ten times more. If after reading the questions will remain and you will need detailed instructions, then leave your wishes in the comments to the article and we will write step by step leadership alterations of chainsaws to a specific unit that will meet the most wishes.

What can be made from chainsaw friendship

Technique that can be made with your own hands from has a large list. Everything is limited only to the fantasy of the wizard. On the Internet published a lot of video with a detailed description of step-by-step making homemade. As part of the article, we collected only the best videos, on the basis of which you can easily make the technique you need. The simplest homemade is the boat engine, and a complex - all-terrain vehicle, a motorcycle, a lawn mower. We give examples of homemade from simple to complex.

Tire knife

This handling does not have a direct relationship to a chainsaw friendship 4, but is in demand, because The knife from the tire of friendship chainsaws very well sharpening, resistant to corrosion. For the manufacture, only the tires from the saw will be required. The price in the secondary market varies from 200 to 500 rubles. For the implementation of the crafts, we offer to see an interesting video, the author of which describes in detail how to make a kitchen knife from the tire. The feature of the video is that the author shows a simple method of doing the hole in steel handles, without drilling.

Bicycle

To make a bike with a jet from a chainsaw friendship, you will need a saw and a bike itself, preferably a kama with a trunk. Self-timer manufacturing process:

Secure the engine on the bike frame.
Make a gas cable and trigger on the steering wheel.
Connect the circuit with a drive wheel of a bicycle and pulley on a saw engine.

Mower (lawn mower)

To make a mower, it will again need a chainsaw friendship 4, small wheels, knife and metal rolling for the manufacture of body and protective casing. The knife is suitable either from the motocos, or from the lawn mower, it all depends on which the working diameter will be laid down by the project. We present to your attention to the review of the video, the author of which made a mower from the chainsaw of the Ural (there is no significant difference from friendship, so we recommend for viewing).

Boat motor

Redo the chainsaw to the boat engine will already be much more difficult than in a bike or mower. The product will be aimed at contact with water, and with it, as you know, you need to be extremely attentive. On the recommendations of many masters, the drive and the shaft is better to use from the old boat engine. The engine from friendship 4. It will only be able to connect them together. For example, we recommend to see an interesting video, the author of which made a boat engine from chainsaw Friendship 2. The author demonstrates the work of the saw in a barrel with water.

Pilorama

To make a panel of chainsaws, it is enough to make a device for the longitudinal dissolution of the log. Her task is to hold the saw tire in a flat plane relative to the log. For a visual presentation, we recommend watching video demonstrations to the device. From the video it becomes clear that for homemakes you need a minimum of materials - ordinary metal rolling (profile tube).

Werethod

Alte the chainsaw to the all-terrain vehicle is already very difficult, but still possible. On the Internet a lot of video, the authors of which have implemented this idea. The whole point is that it is necessary to make your chassis: frame, wheels, drive, etc., and a friendship chainsaw will be used as an engine 4. The only recommendation is to use conventional cameras associated with perimeter instead of wheels. It is easier for those with tires, respectively, the motor will be much simpler while driving.

On the review, we suggest to see the interesting video about the homemade all-terrain vehicles from the chainsaw Friendship 4. In the homemade, the scooter is used, Gouska, so it is most likely a snowmobile than the all-terrain vehicle.

Motinal (Motob Assrobrik)

Making motoes from chainsaw Friendship 4, as in the case of all-terrain vehicles also boil down to the initial design of the chassis: frame, caterpillar, control, etc. And the saw of the saw is just a driving force.

We offer to see an interesting video, the author of which shows how to make the motorcycle of almost from the girlfriend. For example, caterpillage hooks are made of conventional plastic pipes, and the entire carcass of the motor-rider is welded from a conventional profile pipe of small diameter.

Helicopter

Alteration of chainsaws in the helicopter is most likely the experiment, there is no practical application. On the Internet there are video of aircraft whose authors have developed such projects and implemented, for example, a homemade aircraft aircraft.

Conclusion

Friendship 4 is the perfect option for handicrafts with your own hands. Inexpensive and affordable, spoil not pity, a bunch of ideas for implementation. The main thing is desire, if it is, there will be a mower, and a boat engine, and all-terrain vehicle, and much more. Good luck, engineers!

Traditionally, gasoline saw is used to saw wood. However, during the time of total deficit, the craftsmen were pronesed to use it as a drive for other machines and mechanisms. Homemade from chainsaws can make anyone who understands the mechanics and can keep the tool in their hands. Thus, you can build an interesting and useful device in everyday life.

Useful chainsaw items

It all depends on the fancy of the master. From the motorcases can be made:

snowmobile;
motorcyboard;
motovibic (moped);
motor cultivator;
lawn mower;
motobur;
boat engine;
snowmader.

Snowmobile is very simply made on the basis of a small bike. A ski is put in front, behind the whole axis put a pair of ultra-low pressure wheels. Such a homemade from the saw "Friendship" or "Ural" is pretty vigorously on the ice or risen snow.

For a deeper loose snow, such a model of a snowmobile is unsuitable, the power of the saw of the saw is not enough. A more versatile is a snowmobile using a caterpillar. The simplest caterpillar is collected from the conveyor belt. The role of the hooks is performed by flat wooden slats attached to the ribbon. Because of this, such snowmobiles are traditionally called "chopsticks".

The same principle is used in the construction of motilityrs (motple). This option is even preferably a regular snowmobile, since this homemade from the "Ural" chainsaw allows you to move even on loose snow. In addition to the engine on the motorcycle rider or snowmobile, you need to put a gearbox to reduce the number of revolutions with a simultaneous increase in the moment.

Bike with a motor from chainsaws with their own hands to make the easiest. For this, any frame bike is suitable. The throttle control cable is excreted on the steering wheel. Chainsaw and bicycle chains have the same links, so no special gears will need. Torque can be immediately transmitted to the rear wheel of the bike. It is only necessary to put the stars on the rear wheel with an increased amount of teeth to increase the gear ratio and increase power. This will fall speed. It is good because the usual bike is not intended for driving with a speed of more than 20 kilometers per hour.

Motor-cultivator can also be done using a chainsaw as a drive. However, the power of the motoblock from chainsaws is small, and it does not have widespread use in agriculture. We are unrealistic with such a device with such a device, but Prashing the groove for planting potatoes is quite.

The lawn mower is also going simple enough. The basis is the usual manual four-wheeled cart. The engine from chainsaw is mounted on top. The torque is transmitted to the hard shaft, the second end of which is derived under the bottom of the cart. There is an either a metal knife, or a block with a fishing line from the trimmer.

For the manufacture of a motorized drum, a small worm gearbox and auger from fishing ice is required. Such a device can be without effort to drill a large number of holes in winter on the river. If the boring is planned to be used to drill holes in the ground, auger and the nozzle will have to strengthen.

For construction from chainsaws of the self-made boat engine, the gearbox is not needed. It is only necessary to cook the frame with two clamps for fastening on the trauma boats and install the rowing screw on the shaft. Those who did homemakes from the Trimmer do it yourself, easily make a boat engine and from chainsaws.

You can construct from the motorcase and the simplest snow blower. To do this, you need to install the saw on the cape from the skew and add a homemade auger knot. The guide for the snowdown can be made from a conventional sewer tube.

The power unit from the saw can be put even on the scooter.

Our hands are not for boredom

Chainsaw "Friendship" optimally use as a motor and drive for the following devices:

generator;
water pump;
pilorams;
circular;
bulgarian.

The simplest belt transmission with chainsaws to the car generator will provide electric light country house or cottage. By the same way, you can connect it to the centrifugal pump to pump water from the basement.

By adding a worm gearbox to a motorcouse, you can easily construct a simple winch.

The likeness of the belt sawmaker is easily constructed from chainsaws.Where instead of the ribbon will move the carriage with a saw fastened on it. This design will allow himself to dissolve the trunk of the tree on the bar. Theoretically, you can saw and boards, but because of the widespread cuts there will be large losses.

Technique on the verge of fiction

In the Soviet Union, the story of the prisoner went for a long time, who was able to fly from the zone on the homemade helicopter made from the chainsaw. In fact, it is just a beautiful legend, although it has real scientific developments.

In 1971, a group of students of the Moscow Aviation Institute presented a new unusual development to the Council. It was a flying single platform with eight engines from the chainsaw "Friendship"Synchronized in one block. Experienced specimens of these developments were repeatedly shown at various exhibitions. Despite this, serially such models have not been issued.

The dream of the sky for lovers to design anything from the chainsaw is still a dream. Nevertheless, attempts to make a returned single helicopter using engines from "Ural" or "Friendship" do not stop.

Gasoline saw is a good assistant when bilking firewood, spilling trees, leaving the garden, cleaning the overgrown area. Its base is an internal combustion engine, which is characterized by compact sizes, reliability, a small mass, good power indicators. Such advantages of the drive make it possible to create various original homemakes from chainsaws: a motoblock, a grinder, a snowplow, a lawn mower, a sawmill, an electric generator, karting, snowmobile. The motor is also installed on a bike, a boat, making these means of movement more practical. At the same time, often the craftsmen use not only the engine, but also other parts from the aggregate. Difficulty in alteration lies in an accurate fit on the size of the parts of the assembled technique.

Make a boat engine from chainsaws is not difficult. Removing are performed as follows:

remove the tire from the saw;
instead of it to the motor, using a special adapter, join the boat screw of independently or factory production;
then the entire design is fixed on the boat so that the rowing screw is imbued into the water at an angle.

Instead of adapter, some craftsmen install gear. Possible result of the work is demonstrated in the photo below.

For fishery lovers, the homemade boat engine is an economical option that allows you to significantly speed up the movement along the water stroit of lakes, rivers, ponds.

Collection of pyloram

When building houses and other buildings from logs often have to dissolve them on the bar. Pylorama from chainsaws allows you to make it as efficiently as possible with good cut accuracy. At the same time, the tool itself does not require any alterations. Its simple fix in frame Made, for example, from metal corners or profile pipes. Processed logs are stacked by guides. The whole design is presented in the diagram below.

In the homemade sawmaker, the log is not moving: a carriage with a saw fixed at the desired height (depending on the thickness of the sawn timber) with four screws. Due to the fact that the frame moves exactly, the sawing occurs neatly, the cut is smooth. Created tool (its version is presented on the photo further) allows you to also cut the boards without any problems, harvest firewood.

A small minus is the formation of a large amount of sawdust. This is due to a significant chain thickness.

Homemade Bicycle with Motor

Folk craftsmen invented many options, how to redo the bike in the moped. Their meaning comes down to the following:

bicycle is taken;
a motor with a gas tank is attached to the trunk or frame;
a gearbox is established (having a gear ratio 18 to 1) and a special transmission;
additional shock absorbers are mounted;
put a brake.

Instead of gear used two gear couplesconnecting with each other with a bicycle chain. As a basis, various old bikes are often taken (as in the photo below), and more modern (mountain) models are used much less frequently.

Usually a bicycle with a motor from chainsaws is made for the sake of entertainment: such a motorbike rises with the speed of normal.

Homemade lawn mower

Lawn mowers are equipment for harvesting grass. They are applied by owners of private houses and cottages to give land plots attractive, well-groomed appearance. The factory production models are easy to operate, but in price they are not available to everyone. Made independent lawn mower from chainsaws will be much cheaper than branded analogues. Its possibilities are quite enough for domestic use.

Homemade masters collect different types and opportunities self-made lawn mowers. But any design provides for the presence of such elements:

drive;
framework;
pens;
wheels;
knives;
control systems;
protective casing.

Manufacturing process Lawn mowers run in the following sequence:

weld the frame of suitable size, for example, from metal corners 25 by 25 mm;
with bolts or welding to the frame, pens from iron tubes are attached;
in the corners of the frame, the wheels are mounted;
remove with a gasoline saw handle and a tire;
the remaining part of the tool is screwed to the frame using spills with nuts so that the shaft of the gearbox, inverted by 90 degrees, was directed down;

extend gas cable;
from two metal tubes, a telescopic shaft is made, which then attach to the reducer;
make a knife independently (for example, from the hand saw blades) or acquire a factory product;
with the help of bolts or welding combine it with the shaft.

Fit wheels from baby stroller, with old car. If you use pipes of different diameters, you can make a telescopic handle with the possibility of adjusting its length - it improves the convenience of operation.

Knives There are different designs. The simplest of them is presented to the next photo.

The presence of a telescopic shaft will allow you to adjust the height of the herbal intercourse.

Knives from high-quality steel are not afraid of meetings with small stones. They are able to mow even non-body bushes. Homemade mower some craftsmen additionally equipped tracerbianThanks to which there is practically no cut-off on the site.

Snowmobile manufacture

Homemade masters managed to make a snowmobile from chainsaws. The machine consists of the following structural elements:

frames;
internal combustion engine (DVS) with a capacity of about 5 hp;
suspension having a shock absorber;
steering;
passenger seat;
skis or caterpillars;
control systems (clutch, gas).

Snowmobile own production can be equipped skiing or caterpillars. If you put skis, the Aerosani will turn out to be like a sample of equipment below. The movement of such a car will be carried out due to the rotation of the screw. Aerosani make it easier than snowmobile.

When choosing the caterpillars, an important point is the organization of a well-thought-out node for transmitting the rotational torque to them from the engine. On the snowmobile created, the possible appearance of which is shown in the photo further, you will need to install a centrifugal grip along with a chain and a belt. To increase the traction capabilities of the drive, it is recommended to equip the tracked shaft of the larger diameter gear than that of the engine.

As a steering wheel This detail is suitable from a bike or from a scooter. You can also make it made of metal tubes.

The more powerful will be the installed internal combustion engine, the greater the lifeline will have a collected snowmobile.

Creating a trimmer

Trimmer, like a lawn mower, is used to mowing herbal cover on the plot. But motocos used under relatively smaller scope of work or on theuneven localities, stony soils. The trimmer from chainsaws, made independently, will cost much cheaper than its factory counterpart. The productivity of such an aggregate is quite high.

The most simplest option for creating motocos is the use of special factory nozzle on gasoline sawWorking with which is shown in the following video.

Snow blower with a gasoline saw engine

In order not to scat out the snow shovel in the winter season, it is quite possible to independently make a snow blower from chainsaws. For the practical implementation of the project you need engine with a power of about 3 kW (4.1 hp), for example, from a saw "CHTIL". In addition to the drive, the snow blower consists of such nodes and details:

a fence compartment with a vest inside with blades;
pens;
frames;
throwing snow.

All these nodes are visible in the following photo.

The craftsmen are presented wheeled and equipped with stern grades of a model of snow removal techniques. The last option is simpler in the constructive plan for incarnation. The design version of the frame and the intake compartment is shown in the photo below.

Highlights are the selection of a pair of gear and in the manufacture of a good auger (shown in the photo below), which will be driven through the chain transmission.

For the manufacture of housings of the fence compartment Wine galvanized sheets are suitable. Screw blades often make thick rubber. A sewer pipe made of plastic is quite suitable as a snow dropper.

Production of Bulgarian

The angular grinding machine is a multifunctional tool required when conducting a number of works. Despite its availability and prevalence, the craftsmen made by Bulgarian from chainsaws (the sample is demonstrated in the photo below).

The disk of such homemade equipment will rotate not by an electric motor, but an internal combustion engine from a saw.

Build Bulgarian With the use of special adaptation for chainsaws, this happens like this:

with gasoline saws remove the chain and the tire;
install on the shaft of the gearbox pulley;
instead of tires, a special nozzle is also mounted with a pulley, pre-put the belt on it;
stretch the belt transmission as a chain;
attach a protective cover;
put disc.

The collected poultryless Bulgarian gas will help in performing many practical tasks. Its capacity is enough for productive work on concrete.

Assembling Machines for Karting and Buggy

Karting - These are races on small cars (maps), not having a body, elastic suspension at the wheels. This machine is designed to drive through a flat asphalt coating, where it is able to develop a sufficiently large speed.

At home, it is quite possible to collect karting from chainsaws and such details:

wheels;
steering knot;
framework;
brake and control systems.

The following video contains a detailed overview of the possible options for self-made kart.

Maps with a gasoline saw motor costs relatively inexpensive. For children, it will be a way to exciting pastime.

Constructively and on purpose similar to the card, but they have a suspension. This feature makes it more convenient to ride the rough terrain (off-road).

Independent assembly of buggy is similar to making a map (except suspension) and is performed in such a sequence:

weld the frame;
make a suspension, for example, torsion type;
make steering parts;
collect suspension;
mount the steering wheel and thrust;
attach wheels;
put the brake;
install the chair;
enshrine the engine.

To transmit rotation from the motor, the wheel is used or belt. Accordingly, the sprockets are installed or pulleys. So that the car worked quieter, improve the existing silencer gasoline saw Either make a new one. There are options for self-made machines that can develop speed of more than 40 km / h, so you need to go carefully so as not to fall into an accident.

Electric Energy Generator FROM FROM chainsaw

Most modern devices are powered by electrical energy. In the distance of power lines, it is obtained mainly from the electric generators. Similar portable type equipment together with batteries use and in hiking conditions. In order to save money, you can independently make a chainsaw generator. Schematically, its design is presented below.

The following design elements of the portable electric generator correspond to the photos above the numbers:

gasoline Saw;
transmitting gear;
drive belt;
planck for tension;
electrical generator;
control Panel;
clamps;
focusing saw;
fastening nut (designed to join the gearbox);
lead pulley.

Homemade mini-power plants equip alternating electrical generators or DC (for example, from a car by 12-14 V). From this depends the magnitude of the output voltage and its current current characteristics.

Motoblock for home use

Motoblock is an agricultural machinery, which, thanks to the possibility of installing various nozzles, can plow and cultivate the soil, make furrows, as well as perform other operations. In essence, powerful models are mini tractors. Factory-made technique is expensive, cheaper will cost a motoblock from the chainsaw of his own manufacture.

The assembly of the unit does not differ in difficulty. A homemade motor-block device is shown in the video below.

The design performances of the motoblocks made by folk craftsmen, a lot. You should choose the most suitable option for the available components and functionality.

Agricultural cultivator with his own hands

The cultivator is a technique designed to explode the soil layer and cutting the roots of weeding plants in it. The worker body of the unit is rotating cutter. Due to its rotation, the movements of the cultivator on the processed area occurs.

By its capacity, the motor-cultivator is inferior to Motoblock. For the latter there is a special cultivating nozzle.

The cultivator from the chainsaw of its own assembly is quite suitable for the processing of a small area. The design option of such self-made equipment is considered in the next video.

Gasoline Saw

The rank is a highly specialized technique that is used for potato emphasis. At the same time, weed removal between rows.

Assembly from chainsaws easy. Its design is shown in the diagram below.

The following design elements correspond to digital designation in the diagram:

1 - handle motor control;
2 - cable;
3.4, 7, 10 - asterisks of gear;
5 - chain;
6 - wheel;
8 - handle;
9 - fuel tank;
11 - Motor mounting;
12 - playground under the engine;
13 - DVS;
14 - frame;
15 - Plow (Skatenk Nozzle).

In addition to the options considered, taking the drive from a gasoline saw as a basis, you can make a quad bike, mini-helicopter, winch, yamobur or icework. For most homemakes, a 2-3 kW engine is suitable (approximately 2.7-4.1 hp), for example, from chainsaw "CHTIL", "Friendship", "Ural". But the helicopter will require a motor with a large data parameter. To find out the required specific amount of power, it will be needed in this case to carry out accurate engineering calculations.

For reworking it is recommended to use an old inexpensive tool so that in the event of a quick breakage of the created mechanism not to incur special financial losses. It is better to use models that are easily disassembled, and it is not difficult to find parts on them if necessary is not difficult. During the assembly, it should be carefully combined the details, following them that they docile without problems. Pre-created drawings will make it easier and accelerate the process. In any case, the self-made unit must be safe.

- This is an adaptation that sometimes is simply indispensable in the farm. Work speed, high performance, ease of operation - only a few advantages of this device.

However, not all consumers know that the use of chainsaws is not limited exclusively to work with wood, and many of its structural parts are so functional that it is possible to build completely new mechanisms, completely dissimilar to the original design of the gasoline apparatus.

This is due, first of all, with the structural characteristics of the chainsaw: its engine is reliable and unpretentious, and the fuel leak is almost completely excluded. About what can be made from chainsaws, then will be discussed.

Features of the creation of a motobur from a gasoline saw

In order to make a motobore with their own hands from chainsaws, first need to adjust the engine speed, since maximum indicators will not be required for comfortable and safe operation.

With this task, you can cope with such an element as a gearbox that needs to be copped with the engine chainsaws. At this stage, it is important to consider the fasteners system so that parts of the future design are tightly connected to each other.

In order for the device to work reliably, the roe and knives need to be selected so that these part be coincided with the "native" mechanism.

Motobur from chainsaws. The video demonstrates the use of the tool as a boraner for ice.

Chainsaw scooter

With the help of the engine, the chainsaws can be assembled not only to manual fittings, but also a full-fledged vehicle operating on a fuel combustible. One of these structures is a homemade scooter with a motor from chainsaws.

To create this device, you need a regular scooter equipped with a manual brake system and inflatable wheels. The engine from the saw must be fixed on the rear platform of the scooter and make sure that the line of engine stars and rear wheels coincides.

To control the energy supply level on such a scooter, the manual accelerator needs to be connected to wires that are responsible for switching on and off the chainsaw motor. In the event of difficulties, the installation of a special pedal is allowed.

Bike with engine from chainsaws, the so-called moped. The principle of engine use is the same as the scooter.

How to mount a panel of chainsaws?

One of the devices where the structural parts of the chainsaws are used to work with wood not only in order to cut it - it is a panel with which it is possible to splash the bars of the desired diameter.