What homemade products for the household can be done with your own hands. How to make homemade machines and fixtures for the home workshop

It's nice to see when a person made all and other household items with his own hands. To simplify the process of cutting metal or cutting wood elements, they build home-made machines and fixtures for the home workshop. This solution saves not only time for the manufacture of products, but also money for the purchase of finished products. A few practical and interesting options are discussed below.

DIY pipe bending machine

Read in the article

How to use homemade machines and fixtures for the home workshop

The use of home-made machines and devices for the home workshop is aimed at solving several problems:

Simplification of the metal processing process. In the course of creating household items, a metal carver or a press is often required.
Improvement in wood processing. Even to build a small barn or make a wooden one, others are needed.

Buying a ready-made tool is quite expensive, so the use of home-made machines and accessories for the garage is becoming more and more relevant every day. Among the most common options for home tools are:

carpentry workbench;
device for quick sharpening of knives;
device for sharpening metal drills;
drilling machines;
Press;
cutting disc machines.

Here are a few photos of do-it-yourself tools and fixtures from "homemade" ones:

1 of 4

Practical DIY tool shelves

Before creating devices, and with your own hands, determine the storage location for all devices, so that later you do not have to look throughout the workshop or where everything is. It is not difficult to make a shelf for tools with your own hands, the main thing is to decide on its dimensions and material of manufacture.

The easiest way to make shelves is to assemble them from wood. Do not forget about the need to cover the finished structure with a protective varnish or to prevent rotting and swelling of the wood.

You can create a combined version of a metal support and wooden shelves. Here are detailed instructions for creating such a homemade model:

Image	Sequencing
	Assemble the frame. To do this, prepare two side frames, consisting of 4 corners. Connect elements with . Then, tighten 2 frames together using 4 corners.
	When the frame is fully assembled, proceed to the manufacture of shelves. They can be made from wood or metal, as well as from other improvised dense materials. It is enough to cut the canvases of a suitable size and fix them on a metal base.
	If desired, you can make the rack movable by attaching four small wheels. Or firmly install it in the allotted place in the garage.

You can find other interesting projects and drawings for making tool shelves. Watch a video on the topic:

And also make useful household appliances with your own hands:

1 of 4

We make a carpentry workbench with our own hands according to the drawings: video instructions and photo examples

Among the common do-it-yourself devices, a workbench is distinguished. Durable and dimensional, which allows you to securely fix the workpiece, it is useful for high-quality cutting of wood and creating various elements from it.

The device package includes:

Working surface. For it, a solid one is used to increase the life of the device. The thickness must be at least 6 cm.
Supports. Assembled from wooden beams or metal plates. The main task is to ensure the stability of the entire mechanism.
Vice for fixing the product. If the table is long, you can install two vices at once.
Tool box. A useful recess or pull-out design that provides quick access to the small parts you need.

To independently assemble a carpentry workbench for your workshop, you should choose a drawing, purchase material for work.

Do-it-yourself carpentry workbench drawings

Before buying materials to build your own workbench, you should think about a detailed drawing. It should include the dimensions of the machine itself, it is advisable to note the dimensions of the materials used and their quantity.

For example, a finished drawing of a folding workbench with your own hands may look like this:

Whatever model you choose to create, consider several features of the desktop that provide the convenience of cutting wood:

the height and length of the hands of the master: the height and width of the countertop depend on these parameters;
which hand is working: place the vise on the right or left;
what blanks will be made: selection of the table shape;
how much space in the room you allocate for a workbench.

Given all these parameters, it will be easier for you to decide on the drawings of the carpentry workbench and the dimensions of the machine. Here are some interesting examples:

Instructions for assembling a wooden workbench with your own hands

You can buy a wooden workbench in a store or through online catalogs, but it's cheaper to make it yourself. Let's take as a basis a simple version with typical tabletop dimensions: length - 150-200 cm, width 70-120 cm.

Manufacturing work will include several stages:

Image	What need to do
	Make the top cover from thick ones to make a shield with a width of 70 to 200 cm. Fasten the elements onto long nails, and you need to drive them in from the outside, and carefully bend them from the inside. The working surface of the workbench is made only of wood or.
	Sheathe the lid along the lower perimeter with a 5 by 5 cm timber. This will make it more convenient to mount the vertical supports. The location of the supports depends on the size of the countertop. It is better to make them from a thick rectangular bar at least 120 by 120 mm.
	The carpenter's workbench must be installed correctly. Be sure to fasten it firmly. If it will be mounted on the street under a canopy, then dig holes for the supports. Indoors, use other methods of fastening.

When the structure is assembled, place a vise on it. To fully understand how to assemble a carpentry workbench with your own hands, watch the video:

Making a carpenter's vise for a workbench with your own hands

Professional "homemade" assemble not only tables for work, but also a vise with their own hands according to the drawings. Any design of such a clamp will include several elements:

Supports where each has a sponge for clamping.
Moving clamping jaw.
Metal guides. A sponge moves over them.
Lead screw, for moving elements.
collar. Required to rotate the screw.

In the manufacture of homemade vise with your own hands, you can use various improvised materials. For example, there is a design option from a profile pipe. To do this, prepare several pieces of pipe of different sizes, a steel stud with a large thread and double nuts.

Instructions for creating a verstal vice from a profile pipe:

Image	What need to do
	The largest pipe acts as a body. Supports are soldered to it from below. A 3-4 mm steel flange is put on the back side. A hole for the running nut is drilled in the center, and opposite the front support there is a back sponge.
	On the inner moving part, the front steel flange. A stud is mounted in it, with lock nuts fixed to it. Thrust washers are put on both sides of the flange. The last element is a movable tube attached to the front sponge.

And also watch the video "do-it-yourself vise at home":

Do-it-yourself metal workbench drawings

A metal workbench does not differ much from a carpenter's workbench. At the heart of a rigid metal, not a wooden frame. A vise is attached to it, and the entire workbench is designed to withstand the force of a blow from a sledgehammer.

Do-it-yourself metal workbenches can have one, two or three cabinets, and also not have shelves and drawers for small parts. In terms of strength for working in a garage, you can make an ordinary table of metal up to 5 mm thick and a reinforced structure, where sheets from 10 to 30 mm are applicable.

Here are some useful blueprints for making a metal workbench for your workshop:

How to make a do-it-yourself knife sharpener: drawings and photo examples

No home is complete without a knife in the kitchen. It is rather difficult to make the correct one without special devices: it is necessary to maintain the desired angle and achieve the ideal sharpness of the blade.

For each knife, a certain sharpening angle must be observed:

Razor and scalpel require an angle of 10-15⁰.
Knife for cutting bakery products - 15-20⁰.
Classic multifunctional knives - 25-30⁰.
For hunting and camping, they take a device with a blade angle from 25 to 30⁰.
If you want to cut hard materials, then sharpen at an angle of 30-40⁰.

To ensure the desired angle, it is worth buying or making a sharpening device. For example, you can assemble a sharpener with your own hands.

A comment

Specialist in the selection of tools "VseInstrumenty.ru"

Ask a Question

“If you use sharpening not every day, then 1000 rpm is enough for a quality result and a long service life of the device.

To assemble such a machine, a motor from a “washer” with a power of 200 watts is useful. Completely to create a grindstone from an engine from the Workflow for creating such a simple device will be as follows:

Sand the wood blocks with sandpaper to remove any burrs. Make a markup depending on the desired angle.

Attach a stone to the drawn line to sharpen the blade. To do this, attach it to the bar and mark its width. Then, on the markings, make cuts, up to 1.5 cm deep.
In the resulting recesses, fix the abrasive bars so that the grooves match. Then, install the sharpening stone by screwing it onto the bolts.

There are many ways to make a homemade knife sharpener. Choose the right one and try to create a convenient and useful tool for the home.

How to make a do-it-yourself tool for sharpening a drill for metal

They independently make not only a sharpener for blades, but also a machine for sharpening drills for metal. Here are some drawings to help you get started:

Ready-made home machine The simplest and most common version of such equipment for the garage is a converted drill. For work you will need:

bed for the base;
rotation mechanism;
vertical stand.

For a rack, boards are usually used. The mass of the drill is small, so there is no need to use metal. In this case, the frame must be made massive in order to reduce vibration during the operation of the device.

To correctly connect the bed and the vertical stand, as well as assemble all the equipment into one whole machine, pay attention to the video instruction:

Do-it-yourself drawings with dimensions for a drilling machine

To properly make any machine or practical device for private use, you first need to make a drawing with dimensions. Only then proceed to the preparation of materials and assembly of the device.

Here are some examples of do-it-yourself drilling machine drawings from a drill:

And you can also make homemade vise for a drilling machine. Below is a video instruction for assembling such a device:

Article

Interesting homemade products for giving are waiting for you in this article. You will learn how to make a lawn mower from an old washing machine, make a sink, a country shower, a dryer from improvised materials.

Useful homemade products for giving - do-it-yourself washing

Not everyone has the financial ability to buy a Karcher car. If you can't buy it, why not invent it? Do-it-yourself washing will allow you to do without plumbing, reduce water consumption and thoroughly wash your car, fence, garden path or other items.

Here's what you need for such a homemade to give:

plastic canister with a capacity of 5–20 l;
hose connector kit;
automobile nipple;
piece of hose;
silicone sealant;
sharp knife;
compressor or car pump;
irrigation gun.

Take a set of hose nozzles, which includes 2 connectors, a 3/4 threaded fitting, a 1/2 adapter.

Here is the principle of operation of such a homemade product for giving: you connect the gun to the hose, attach this device to the bottom of the canister. A nipple will be built into its neck.

Fill the container with water, but not to the top. Then screw on the lid and pump air in. This will create pressure, and the water will run well when you start to pull the trigger of the gun. Here's how to assemble such a mini sink.

Carefully cut a hole in the lid with the tip of a knife. It should be slightly smaller than the diameter of the nipple stem. Also cut a circle of the desired diameter at the bottom of the sidewall of the canister.

Insert the nipple into the cap.

Now, helping yourself with the wire, place the coupling in the hole intended for it. Apply silicone sealant to secure the coupling to the canister.

It is necessary to tighten the cover and carry out other work only after the sealant has completely cured. Then you will connect one end of the hose to the water gun and the other to the canister.

Pour water into the container, but not to the top so that there is room for pumping air. But do not pump too hard, so that the canister does not deform and burst under pressure. See how the fitting should be screwed in and the connectors installed.

If everything is done correctly, then when you press the trigger of the water gun, the water will spurt out in a good stream. You can adjust the pressure by twisting the tip of the gun.

In the country, it is hardly possible to do without a shower. Try to make something unusual, but tropical, then you can enjoy even more water treatments.

How to make a rain shower from improvised materials for a summer residence?

If you have only recently acquired a plot and you do not yet have a washing room, then you can take a shower right on the street, enclosing a small area near the fence with a curtain. To make such a rain shower, you will need very few components, these are:

bracket;
wire;
flexible hose;
metal beer can;
hose adapter;
awl;
nails.

Nail the metal bracket onto the wooden fence to get the fixture at the right height. Screw the adapter to the tip of the hose, fix it on the slot of the beer can. The joint can be treated with a sealant. Using an awl, make many small punctures in the jar.

Tie the top of the hose to the bracket with wire, and attach the other end to a water pipe or pump. When you lower the pump into a barrel of heated water, you will be able to enjoy pleasant water treatments.

You can also make a rain shower head using a disc container. In its center, you need to fix the plastic adapter that is attached to the shower hose, and the central axis of the discs must be removed. Using an awl, make holes at the top of the lid. Glue all fasteners well with sealant. Such a nozzle is held on the bracket with a thick wire or on a rigid pipe.

If you have a desire to make a rain shower, then you can use plastic pipes for this.

You need to bring water to them, first make a lot of small holes with a soldering iron, and then enjoy the pouring drops. Children really like such water procedures.

But do not forget to first check the water in the container from which it will be poured into the shower, it should warm up in the sun.

And to make a stationary shower, you must first pour water into a tank or barrel, which will be located under the roof or on the roof of the building. On a warm summer day, the water here warms up well, and you can wash yourself plenty. To be able to do this in cooler weather, then it is necessary to provide a heating system in such containers.

Do-it-yourself country shower

Before installing it, you need to make a shower cabin. If possible, you can make it out of wood by placing this small structure on the base. Put in a wooden door or go with a shower curtain like this.

There are also simpler options. If you have oilcloth, then use it.

Another option is to purchase impregnated fabric or use an old awning or tent.

If you made a fence from corrugated board and you still have materials, then try to make a shower for giving from them. Metal pipes need to be dug in according to the markup, poured with concrete. When it dries, cut sheets of corrugated board are welded to the racks. One of them will become the roof.

If you don't have enough wood planks, then implement the option shown in the next photo on the right. And on the left is a shower, which is made like a wattle fence. So the materials for it will cost almost free.

When the shower is ready, you can install a water tank on it. To make it warm up better, you can make a kind of metal or hose coil. Then the water will warm up more actively.

These and other homemade products for giving allow you to make the most of the available containers.

To be able to get warm water even when it is not heated by the sun, use electric heating. To do this, you can position the plastic barrel vertically or horizontally. Then it will be necessary to mount the ten on one side, and on the other? water inlet fitting. Make an overflow hole so that excess liquid flows out, and you can see that the container is already full.

Now it remains to install the tank. Usually, a shower roof is used for this. You can put a flat tank here, made of iron or plastic. You can also make a soul canister from a metal or iron barrel. If you need to heat the water, then a heating element is mounted in the barrel.

Check out other examples of what you can do in your backyard with your own hands.

Interesting homemade products for giving with your own hands

Garden tools are very necessary for working on the ground. Often in the store they sell not very high-quality sets. After a short use, the handle of the shovel breaks off, or the teeth of the chopper are bent. Therefore, if possible, try to make tools with your own hands.

Take:

cutting;
fragment of a water pipe;
scrap from a two-handed saw;
screws;
screws;
a fragment of a profile pipe with a cross section of 3 cm.

Using a grinder, cut a piece of pipe. Taking a lever tool, you need to cut a piece of pipe, unbend the sector, and in the place where the stalk will be, you need to work with a hammer to give the future chopper the desired shape.

To make a blade, take a piece of a two-handed saw and draw the outlines of a future chopper. Punch two holes.

At the same distance and the same diameter, you need to make 2 holes on the chopper itself, and then cut out a fragment from a two-handed saw.

Drill these holes with a drill and a drill designed for metal work. Connect these two parts with rivets, which are screws.

Now drill a hole in the top of the chopper to attach the handle here.

Make also a scoop, which is very interesting to work in the beds. Then such homemade products for giving will allow you to get a very durable set of tools.

Saw off the desired piece of the handle with a grinder and begin to unbend its part with a chisel.

Then, helping yourself with lever tools, straighten this part almost completely.

It remains to work with a hammer so that the scoop blade acquires the desired shape. Using a felt-tip pen, draw the outlines of its working part and cut it out with a grinder.

Using an abrasive wheel, clean the edges of the shovel and make them more even. Now process the tool with an emery petal wheel. That's how shiny this shovel will become.

Also drill a hole in it for the handle, then insert it and secure with a screw.

Cover the cuttings of both tools with an antiseptic, and then with varnish. Now you can use the tools for their intended purpose. If you want, follow the same principle to make a cultivator for beds.

It is very exciting to create such things for giving with your own hands. Maybe after you make the tools, you will want to make a device on which you can dry part of the harvest. See how one gardener did it.

How to make a dryer for fruits and vegetables?

See what materials you need to take for this:

sheet metal;
square pipes;
locking mechanism;
polycarbonate sheet;
self-tapping screws, screws;
2 door hinges.

But what tools you need to arm yourself with:

grinder;
welding machine;
drill;
stationery knife;
tape measure and marker;
scissors for metal;
hacksaw.

First you need to make the basis for the drying cabinet. Make a frame from square pipes. Horizontal and vertical posts are sawn off so that the edges are even. And the ends on the connecting elements should be bevelled.

The door here will be metal. To make it, cut 4 fragments from an iron pipe and weld them into a rectangle. Then you need to sheathe this base with metal, using screws with nuts and self-tapping screws. If possible, weld a steel sheet. To make a mount for baking sheets, attach wooden blocks to the back of the frame. Take self-tapping screws for this. In this case, on each side there are 4 wooden blocks for 4 baking sheets.

An absorber is installed in the dryer. Take sheets of metal and paint it black. Use heat resistant paint. When it dries, put this blank on the bottom of the dryer.

For the absorber, take a thick aluminum or copper sheet, in extreme cases, steel. These materials conduct heat well.

Now you need to sheathe the dryer from the outside, make the roof transparent, made of polycarbonate. Then the sun's rays will penetrate well here. You can also use glass. Cover the ventilation windows with mosquito nets to keep insects out.

Attach hinges and a locking mechanism to the door. Fasten the door in place. See what a wonderful beautiful and roomy dryer turned out.

It remains to make the opposites. They must be breathable. First, knock together the frames from the bars, and then attach a metal mesh to them.

Now you can cut fruit and watch how your device will work. Put a thermometer in the dryer to monitor the temperature. It should be in the range of 50-55°C. At lower temperatures, cover the lower openings by placing a rag here.

In such a home-made dryer, you can dry not only fruits, but also vegetables, herbs, fish, meat, roots.

If this diagram of the device of such a device seemed complicated to you, then you can make a dryer from a metal barrel. A hole for the door is cut out in it, and racks made of metal mesh are inserted inside.

So that water does not flow here and there is better ventilation, such a roof is installed on top.

You can upgrade this fixture with a fan and an electric heater inside.

If you want to make a lawn mower with your own hands, then this is also possible.

Turn an old washing machine into it, for example, like this one.

And if you still have an old bedside table, then you will make a platform out of it for a future almost self-propelled device. But you only need a door from the nightstand.

Drill holes in the center of the motor shaft. Make a cutting knife from an old two-handed saw. It is necessary to saw off from it to the size of the desired shape, cut a recess inside.

Attach two wooden pickets that will become the handles of the mower. Do not forget to fix the motor and extension cord to it. Now you can experience such an interesting unit.

If you are interested in other homemade products for giving, then it will be useful for you to watch the following video.

A lot of interesting ideas are waiting for you in the first video.

And you can get acquainted with cool homemade products from plastic pipes if you watch the second story.

Since you have decided to become a self-taught electrician, then for sure after a short period of time you will want to make some useful electrical appliance for your home, car or cottage with your own hands. At the same time, homemade products can be useful not only in everyday life, but also made for sale, for example,. In fact, the process of assembling simple devices at home is not difficult. You just need to be able to read diagrams and use a tool for radio amateurs.

As for the first point, before you start making electronic homemade products with your own hands, you need to learn how to read wiring diagrams. In this case, ours will be a good helper.

Of the tools for beginner electricians, you will need a soldering iron, a set of screwdrivers, pliers and a multimeter. To assemble some popular electrical appliances, you may even need a welding machine, but this is a rare case. By the way, in this section of the site we even talked about the same welding machine.

Special attention should be paid to improvised materials, from which every novice electrician will be able to make elementary electronic homemade products with his own hands. Most often, in the manufacture of simple and useful electrical appliances, old domestic parts are used: transformers, amplifiers, wires, etc. In most cases, it is enough for beginner radio amateurs and electricians to look for all the necessary tools in a garage or a barn in the country.

When everything is ready - the tools are assembled, spare parts are found and minimal knowledge is obtained, you can proceed to the assembly of amateur electronic homemade products at home. This is where our little guide will help you. Each instruction provided includes not only a detailed description of each of the stages of creating electrical appliances, but is also accompanied by photo examples, diagrams, as well as video tutorials that clearly show the entire manufacturing process. If you do not understand some point, you can clarify it under the entry in the comments. Our experts will try to advise you in a timely manner!