How to dock a floor covered with laminate and linoleum. How to dock laminate between rooms: docking methods, installation process using a threshold

The following repair scheme is considered a classic practice in construction: removal of the old coating, preparation of a site for the installation of a new coating, and, in fact, the installation itself.

However, this requires additional financial costs for auxiliary materials and a lot of time that is so expensive in modern realities.

Now more and more often when repairing they go the other way. For example, the ceiling: the old paint is not completely removed, but the defects that have appeared over time are simply cleaned, the irregularities are puttied, the film is cleaned again and glued.

Or even simpler - without additional effort, a modern system of any false ceiling is mounted directly on the old surface.

The question of how to lay a laminate with your own hands on linoleum is not at all from the category of oily oil - this intention has its advantages if the docking of the laminate and linoleum is properly organized

Advantages of technology while saving time

In the case of gender, the situation is very similar. And in this way there are many significant advantages, provided that the two surfaces are properly organized (in our case, linoleum and laminate) and taking into account some nuances.

Such an order, when the transition from laminate to linoleum is not accompanied by anything, is not welcomed by technology - if the laminate is on top of linoleum, the latter, at least, must be carefully aligned

In addition to considerable time savings when installing laminate on linoleum, there are also many other advantages. So:

Abandoned old linoleum provides additional sound insulation
If the old linoleum was insulated, then after laying the laminate, the floors will become even warmer
Existing small "waves" of linoleum are easy to hide with a new coating.
Indoors, a more technological and modern flooring appears, but this is more for lovers of innovation.
The cost of auxiliary materials is minimal
Significantly reduces installation time, as there is no need to dismantle the old coating

There are few disadvantages of this method of laying a laminate, however, one should not forget about them:

It is imperative to find out the reason that led to the need to replace the old coating. If, for example, the waves on the linoleum appeared due to high humidity, then laying the laminate under the current conditions is unacceptable.
To begin with, it will be necessary to dry the floor, and for this, in any case, you will have to dismantle the old coating. Returning the old coverage after it will no longer make sense
If the linoleum is not deformed due to moisture, leveling the surface will still be mandatory, since laying the laminate on an uneven surface is also unacceptable.

The direct junction of laminate and linoleum can be completely eliminated if the laminate on linoleum is laid on top of intermediate structural strips

Work progress

In order to figure out how to lay the laminate on top of the old linoleum, you need to meet some conditions.

These conditions, for successful work on joining the laminate with linoleum, include the following:

Due to the fact that the laminate is a polymeric material, it must be kept at room temperature for some time before installation, preferably at least two days.
Laminate installation rules also require that the subfloor be level. This is checked using the Reiki rule. Differences in irregularities should be no more than 2 mm. If the difference is greater, you need to cut off the most protruding irregularities, and putty the resulting voids. Otherwise, the laminate, at least over time, may begin to creak, in the worst case, the joints will disperse

Such a problem as unevenness is also solved using the laying method, and there are several of them:

Laying with special glue for laminate. In this case, the floor must be perfectly flat, and the gluing of the joints must be thorough.
Docking in a glueless way. In this case, it is also worth taking care of leveling the floor, however, a certain percentage of unevenness is allowed. The slats are fastened with special locks, and are also carried out around the perimeter of the room with skirting boards or with the help of a structural rail gasket.

Of course, the quality of the solution to this issue, how to lay a laminate on linoleum, can also be checked with heels, but this is fraught with danger not only for heels, so it’s better to use a two-meter level

Work order

Thanks to modern technologies used in the production of laminate, the work of laying a laminate is quite simple:

Prepare the surface carefully. If there was a need to dry the subfloor beforehand, you need to pause before installation for 2-3 days
Dismantling old skirting boards
Substrate is being installed. This is not a mandatory process, but the substrate, especially if it is cork or a special composite material, significantly increases the life of the laminated coating.
Laying laminate panels. Manufactured according to the instructions, with the obligatory laying of damper inserts
Plinth installation. With their help, the laminate web is fixed, and the dampers are also hidden.

Laminate on old linoleum is best laid using damper pads around the entire perimeter of the floor

Useful advice! In order to hide the connecting seams as much as possible, laying the laminate should be done perpendicular to the wall with the window.

The idea of laying laminate flooring over old linoleum flooring is a very good one. In addition, it fully meets modern trends in simplifying construction work and minimizing work costs, and also frees craftsmen from doing unnecessary and often unnecessary work.

The most popular floor coverings of the last decade have become laminate and linoleum. Owners furnish residential or commercial premises, fully trusting the reviews of these products. And rightly so, because they are beautiful, practical and durable. So why not use them when decorating an apartment or office. But which material should be preferred if they are both so good?

Experienced designers will immediately answer that it is convenient to use both materials at the same time. This will solve your problem but create a new one. How to perform the correct docking of the laminate with linoleum, if you decide to delimit the room into zones in this way? It is worth considering that the junction of two materials on the floor is made in different ways, the choice is up to you.

Joining two materials

What is the difficulty of joining?

As mentioned above, the most popular floor coverings are linoleum and laminate. And if you decide to use them together, then you will have to study some of the nuances of docking.

The complexity of this event lies in the fact that the thickness of these two materials is different. Linoleum is thinner than laminate. Therefore, the main task is to make their joint as invisible as possible on the floor.

Scheme of laying laminate

This is easy to do if you know how to solve the problem.

Docking methods:

Aligning the height of the linoleum so that its surface is flush with the laminate.
Sealing the joint while maintaining the drop and using additional elements - aluminum profiles or thresholds.

In each case, it is worth approaching the solution of the issue from a practical point of view. After all, the aesthetic appearance of your premises depends on the correct connection of linoleum and laminate.

Single level joints

From the point of view of practicality, single-level joints of laminate with linoleum are the most profitable. The work uses overlays and moldings that make the joint on the floor between the two materials smooth and invisible. But it is recommended to take their choice responsibly, and check how they meet the requirements listed below.

Overlay requirements:

Waterproof, only in this case they will qualitatively connect two joints of different materials. Otherwise, if moisture enters the linoleum or laminate, it will deform, which will lead to damage to the floor.
UV resistant. The joints of linoleum or laminate are not always protected from this influence, therefore, when exposed to sunlight, the lining should not fade or deform so that the junction does not deteriorate.
Ease of installation, otherwise you run the risk of messing around with this event for a long time, pretty spoiling your mood.
Durability and wear resistance. These qualities will help to use pads to connect the joints of linoleum and laminate for many years.

Docking laminate and linoleum at the same level occurs as follows:

another dense material is laid under the linoleum to raise it to the same level as the laminate. Usually this material is multilayer plywood;
with the help of a special lining, two materials are joined.

Multi-level joints of laminate with linoleum are suitable if you want to level the floor from two levels. For these purposes, sills of various heights are produced.

Product types:

straight sills for joints of single-level floors;
transitional - to connect two levels of the floor;
final - to decorate the edges of linoleum or laminate;
corner or stair - to connect linoleum with stairs.

In a hardware store, you can easily find products for joining coatings. The only thing you have to decide is the material of manufacture. The most popular sills:

metal;
plastic;
cork;
rubber;
wooden;
laminated.

products are selected according to their external design. The width and color of such devices can also be any, so you have the opportunity to choose the product to your taste.

Advice! To make a multi-level floor joint aesthetic, it is recommended to use joint profiles or thresholds. They will protect the joints from moisture, and the floor will become even and neat.

Ways of fastening the thresholds

The joints are connected using special strips and sills, which are fixed in several ways:

Through connection. In this case, the connecting strip is superimposed on top of two materials - linoleum and laminate - and screwed to the floor with self-tapping screws.
Concealed connection with fixing strips. The back side of such a bar has special grooves. The front part is flat, which allows you to connect two materials without visible fasteners. Due to this, linoleum and laminate are on the same level.
Instead of connecting - gluing the coating to the floor. This method is less practical, but still it is sometimes used. For use liquid nails or transparent adhesives based on silicone. Such a connection is suitable for places with low traffic, otherwise the joints will be damaged sooner or later.

Planks and sills for joints

To connect the joints of the laminate and linoleum on the floor, sills or aluminum strips are often used. This is due to the fact that aluminum is a practical material that allows you to decorate the flooring depending on the color. Such planks are painted in bronze or gold, so the possibilities of design fantasies are unlimited.

The following types of slats are intended for connecting two materials:

Anodized, which are recommended for use in places with high traffic. Their coating is very resistant to abrasion, so the bronze-colored plank will please the eyes of the owners of the house for a long time.
Laminated, which are advised to be installed in rooms with low traffic. They are less resistant to stress, but do not lose their relevance.
Plastic. The cost of this material attracts many consumers, but you need to be careful with them. They cannot be used in places with high traffic, and they are not recommended to join the laminate with linoleum. But in the absence of financial resources, this option can also be considered.

It is important! Although plastic strips have several drawbacks, you can’t do without them when decorating curved joints of linoleum with laminate. Even a radius connection is within their power.

There are also brass sills, which are of high quality and durability. Accordingly, the cost of this pleasure is high, but if the price is not an obstacle, then it is impossible to think of another option. The only drawback of this material is darkening over time. This is because the brass used for these slats is not machined, so it darkens. But to solve this problem is simple - just rub the bar with felt, and it will play brighter than before.

Docking without straps

If you decide to connect linoleum with laminate without additional planks, you will have to be prepared for the fact that the costs of such work will be significant. To do this, you need to choose materials so that they completely coincide with each other. This applies to the directions of the laminate planks and the pattern on the linoleum.

It is important! With the right choice of material, your floors will always be smooth and beautiful.

But if you can do without thresholds when laying laminate on the floor, then in the case of the second material, you will have to try to ensure that the edges are well fastened so that they do not wrap. This is especially true in places where there is a large passage of people.

To ensure reliable fixation of linoleum to the floor, transparent silicone glue is used. The material is cut as accurately as possible so that the junction is barely noticeable. After connecting the two materials, the gap between them is filled with the same glue.

Advice! To prevent glue from getting on the front surfaces when joining the two materials, use molar tape.

The floor covered with linoleum is quite popular among buyers, as this material is easy to clean and can be used for a long time. Its price is also quite democratic compared to other options for creating a surface. But still, this flooring has some problems during operation: they are separated, which leads to their swelling, which is why it is quite rational to combine several types of materials, for example, linoleum and laminate. But how to connect laminate and linoleum without damaging either one or the other?

It should be added that the coating is practical, economical and easy to use, which has become the reason for its growth in popularity among buyers. Therefore, it is important to know how to join laminate and linoleum in such a way that when connecting these surfaces there is a guarantee that they can be used for a sufficient period of time.

One of the main conditions for successful matching is understanding how these materials harmonize with each other and whether they can be combined.

In addition to taking into account the compatibility of floor coverings with each other when on the floor, it must always be remembered that if the difference in thickness is quite large, the laying of the floors will not be successful. When joining surfaces, the same problem can arise - they often have different thicknesses.

But still, now it is possible to solve the problem of non-joining of various kinds of surfaces - for this you can use strips for joints and joining floor coverings.

We make a joint

How to join laminate and linoleum, what types of planks can be used for this? Empty strips for connecting joints are often used in the threshold area, since they can easily hide the end, as well as additionally fix it. If the side is thick enough, a decorative corner can be used.

What role do connecting and empty strips play in the process of joining the coating, what are they made of? Connecting strips not only serve as clamps in the area of joints of floor surfaces - they can also serve as a designer decoration. There are quite a lot of options for docking materials - they are made in a variety of styles from imitation gold to wood, the range of choice is quite wide.

Manufacturing material options

They are made of aluminum, plastic (laminated). Anodized aluminum is more resistant to inlet use than laminated.

Plastic ones are not very popular among buyers due to the fact that they are amenable to erasure, have a lower level of strength compared to aluminum.

The most stable are the strips for joints made of brass. Of course, their price is slightly higher than aluminum ones. It is not always possible to use this type, since they are not decorated, they remain the same as the brass itself, they do not change color and appearance, but we must remember that they fade.

How can you fix the docking strip?

To do this, take the screws with which you should fasten it to the floor. Fastening can be done in a secret way without the use of screws - this is possible if there is a special groove on the back of the strip in which the screw can be fixed from the opposite side.

In addition to fixing with screws, you can consider fixing with glue if your floor is done.

Video on how to connect linoleum with laminate

Thus, the combination of flooring can be quite harmonious if you match similar styles and designs to match. Connecting surfaces is also not difficult if you use connecting strips, of which there are a fairly large number of options.

How beautiful to dock linoleum with laminate

The floor covered with linoleum is quite popular among buyers, as this material is easy to clean and can be used for a long time. Its price is also quite democratic compared to other options for creating a surface. But still, this flooring has some problems during operation: linoleum sheets are separated, which leads to their swelling, which is why it is rational to combine several types of materials, for example, linoleum and laminate. But how to connect laminate and linoleum without damaging either one or the other flooring material?

It should be added that laminate flooring is practical, economical and easy to use, which has become the reason for its growth in popularity among buyers. Therefore, it is important to know how to join laminate and linoleum in such a way that when connecting these surfaces there is a guarantee that they can be used for a sufficient period of time.

One of the main conditions for successful matching is understanding how these materials harmonize with each other and whether they can be combined.

In addition to taking into account the compatibility of floor coverings with each other when laying them on the floor, it is always necessary to remember that if the difference in thickness is large enough, the laying of the floors will not be successful. When joining surfaces, the same problem can arise - they often have different thicknesses.

But still, now it is possible to solve the problem of non-joining when laying various kinds of surfaces - for this you can use strips for joints and joining floor coverings.

We make a joint

How to join laminate and linoleum, what types of planks can be used for this? Empty strips for connecting joints are often used in the threshold area, since they can easily hide the end of the floor material, as well as additionally fix it. If the side is thick enough, a decorative corner can be used.

Manufacturing material options

They are made of aluminum, plastic (laminated). Anodized aluminum is more resistant to inlet use than laminated.

Plastic ones are not very popular among buyers due to the fact that they are amenable to erasure, have a lower level of strength compared to aluminum.

The most stable are the strips for joints made of brass. Of course, their price is slightly higher than aluminum or plastic ones. It is not always possible to use this type, since they are not decorated, they remain the same as the brass itself, they do not change color and appearance, but we must remember that they fade.

How can you fix the docking strip?

In addition to fixing with screws, you can consider fixing with glue if your floor is made of tiles.