We make angel eyes on the car ourselves. DIY angel eyes Angel eyes from a diode tape

About making do it yourself angel eyes almost all owners of domestic or imported cars think about it, because they want to make their vehicles as attractive as possible. By installing these side lights on the car, you will make them look like the headlights of BMWs of recent years.

Headlights of this kind are their trademark feature. If you really like this kind of headlight glow and that is what attracts you to BMW so much, then it is not necessary to save money for an expensive German. Such dimensions can be made on every third car. The main condition is the round shape of the headlights.

Almost all domestic cars have such a design, for example, VAZ 2106 or VAZ 2110. Just imagine how often other drivers or ordinary passers-by will look closely at your car. Believe me, these headlights are hard to miss!

DIY angel eyes

At first glance, the design of such side lights may seem quite complicated, however, in fact, making angel eyes with your own hands will not take much time and will not require a large amount of financial investment.

All that is required in the manufacture of a beautiful "eye" (parts of the materials can be replaced if necessary):

Jigsaw or metal saw;
Nippers;
Pliers;
Plexiglas bar;
LEDs;
Drill;
File;
Drill;
Soldering iron;
Building hair dryer;
Capacity;
Can;
Insulating tape;
Resistors;
Wires.

Naturally, in order to create angel eyes, you need at least partially understand electrical engineering.

Prepare the required items before starting. Take a bar of organic glass, cut out a pair of blanks for your car (according to the number of round car headlights in which you want to install your own handmade angel eyes).

Organic glass blanks

Fix the LEDs in the rods and cut along the cut every 0.5 centimeters and set the resulting eyes in the place of the headlights.

Diodes inside an organic tube

This has all been described briefly, and now let's proceed to a full-fledged, step-by-step manual for making angel eyes.

How to make angel eyes with your own hands?

Before you start collecting DIY angel eyes from LED strip or plexiglass rods, you must have all the tools and elements that were indicated earlier.

Plexiglas should be in the form of a tube or rod and easily tolerate heat up to high temperatures. If you go to the store, buy an expensive pipe, do not save money, especially since you will need no more than one and a half meters, or even a meter will be enough. The amount of plexiglass can be calculated even before purchasing. Take a meter and measure the circumference of each headlight. Add 2 to 3 centimeters per cut to each measurement and add all the numbers.

Let's say you want to make angel eyes on 4 headlights: two large (circumference - 25 centimeters) and two small (circumference - 15 centimeters). Let's calculate:

(25 + 5) * 2 = 30 * 2 = 60 centimeters for large headlights

(15 + 5) * 2 = 20 * 2 = 40 centimeters for small headlights

60 + 40 = 100 centimeters

As a result, 1 meter of organic glass is enough for 4 angel eyes on the car.

You can find organic glass most often at points of sale of curtains, blinds, construction and repair shops with a bias towards the decorative and design side.

All other items can be bought at regular hardware stores or car dealerships. The resistors must be 220 ohms.

Resistors 220 Ohm

First, measure the circumference around which the plexiglass rod will be placed. Take a regular meter or any piece of thin hose if you have one at your side, and circle the headlights, measuring the circumference. The resulting length is applied to the organic glass tube and cut.

We measure the circumference of the headlight

Now heat this piece of plexiglass to such an extent that it is flexible enough. You can use a hairdryer, soldering iron, or hot water. Wait a while and make sure the tube is warm enough to bend.

Warming up the tube with a hairdryer

Using a pair of pliers, take a heated headlight blank and wrap it around a can or any other structure. Wait for the tube to cool down. The diameter of the tin should be approximately equal to the diameter of the headlight. When working with small rings, you need to be especially careful, since short rods are quite difficult to twist even in a hot state. Be extremely careful not to burn yourself.

Bending of the heated workpiece

When the workpiece has acquired the required shape, has cooled slightly and can be taken in hand, remove it from the jar. Drill holes along the ends of the workpiece, where the LED will be installed.

Drilling a hole at the end of the workpiece

Tip: Drill very carefully and at low speeds. Plexiglas is quite fragile and the resulting thin walls can easily crack under pressure.

When the inner workings with the pipe are finished, work on it from the outside. The procedure is optional, but the effect of "cilia" with a properly made notch will look beautiful on any headlights. It is important to keep the same distance between them.

Take a hacksaw and with light movements make cuts on the surface with the calculation: 1 for every 0.5-1 cm (depending on the length of the tube). They are made circular, in depth they should not exceed a quarter of the thickness of the tube. Notches of this kind will help to emit a pleasant radiant light from the headlights, like a "German".

Notches on the surface of the tube

Secure the diodes in the drilled holes so that they do not dangle. They can be filled with transparent glue, silicone or fixed in any other way.

Securing the LED in the tube

Now you need to solder the resistors to the LED legs.

Soldering resistor to diode connection

Thus, you will need 2 diodes per headlight (one on each side of the tube in the form of a ring) and 2 resistors soldered to the diodes.

Next, you need to solder the cables to our workpiece for easy connection with the old wiring system. Twist the tube into a circle and roll up the edges with electrical tape (if necessary). That's it, the LED Angel Eyes are ready to install.

Insulation of tube ends

The final stage of manufacturing is to test the headlights for operability. To do this, you can connect them to a power source and check if the LEDs are on and if the light is scattered normally. It is important not to mix up the polarity!

Installing angel eyes with your own hands

After the new lights are ready, you need to temporarily dismantle the existing ones in order to connect the wiring. Now install the diodes in the headlight housing so that they are almost invisible.

Installation of angel eyes in the headlight

Solder the new contacts to the old ones, connect them into one "network" and connect it back to the main power supply of the car.

It is best to install the installation at night or in the evening in order to fully appreciate the lighting. You may need more powerful LEDs or a good headlight glass polish.

How to connect bi-xenon angel eyes lenses?

Car enthusiasts are well aware of the benefits of xenon light and how it behaves with lenses. Bixenon lenses with angel eyes look much more spectacular and modern. They fit perfectly under any base and lamp without the need to saw the reflector. All that is needed is to remove the glass, place the lens inside and close it back.

Angel eyes with bi-xenon headlights

If you have very bright LEDs, bi-xenonon lenses prevent dazzle of oncoming vehicles and normalize the light beam.

What are the best angel eyes?

The question is ambiguous and difficult to answer. If you do not take into account the hand-made assembly, then it is better to trust the professionals who have already assembled similar headlights more than once. You can find a person who can custom-made angel eyes very efficiently and quickly on any automotive forum or in social media groups dedicated to this topic.

It is recommended to contact people who have installed such lights for themselves. They know how to correctly select tubes, LEDs and take into account other nuances in order to achieve the maximum glow effect at the lowest cost. In addition, they can show by their own example what the purchased angel eyes will look like.

Prefer to make your own headlights? Make sure to match heat resistant tube and LEDs with suitable light output. Angel eyes with a weak luminous flux will practically not be visible against the background of the main headlights. Very bright LEDs, on the contrary, will only blind oncoming vehicles and impede their movement on the road.

Tuning is a popular hobby of motorists. Manufacturers offer many parts for decorating vehicles that can significantly change their appearance. But often drivers are limited to spectacular optics.

Among the huge variety of alternative lighting devices, angel eyes are the most popular. Design features of this type of optics. Differences between branded kits and non-original kits. And, of course, how to install angel eyes with your own hands? All this is discussed below.

Round headlights with LED strip around, or angel eyes, have always attracted the attention of motorists. More often, this type of optics is installed on executive cars. Angel eyes on BMW cars are considered the standard. This is the recognizable style of the seventh series sedans, as well as crossovers.

Making angel eyes with your own hands is real. The only question is what will happen in the end.

Often, car owners get the idea to change the look of their optics when they see the spectacular BMW headlights. But it is achieved thanks to quality components. Tuning enthusiasts forget about this, believing that there is no difference between expensive and cheap diodes.

The result of such savings is weak LEDs, which not only do not give the desired effect, but also do not last long. It would seem that you can buy the tape again and install it, but this will require disassembling the headlight again. Isn't it better to take a quality one right away?

As it turns out, the original diodes in the store or their copies on AliExspress are expensive. On the other hand, buying cheap ones, the car enthusiast will not only spend several times on the actual LEDs, but will also pay for the installation. So how to make angel eyes with your own hands and save money? Unfortunately, distinguishing high-quality LEDs from mediocre ones by eye is extremely difficult. And in stores, sellers strive to offer a low-quality product from China. And the power of the original or Chinese diodes is significantly different. So, for non-original ones, the maximum luminous flux is 12 lumens. And the branded ones have 100 lumens. A car enthusiast will spend less money if, instead of one LED strip, he replaces a row of LEDs in such a way that their total power is sufficient.

The reader will certainly ask how to make angel eyes with your own hands? This process is not as simple as it seems. And many, faced with installing LEDs for the first time, only care about cost savings. Meanwhile, a good result can be obtained only by taking into account a number of parameters - first of all, luminous intensity.

The most popular option is to make spectacular optics from plexiglass or clear plastic. They are based on LED strips placed in small recesses. But the power of the LEDs placed in the inner part of the material does not exceed 0.5 watts.

A small luminous flux directed forward and inward, part of which conceals, in fact, glass or plastic, will be distinguishable only at night. If you put more powerful LEDs, it still does not help if the direction remains the same. But if you put an LED strip with a power of five to ten watts with a luminous flux of at least three hundred lumens, you can achieve an effect like on premium cars. In this case, the luminous flux should be directed only forward. Otherwise, the car enthusiast will receive only one more set of side lights.

You can also use a light tube to create a red eye effect. These are used as side lights. Cutting the tube and making a ring out of it can give a good result. Moreover, it is quite simple to install such. You just need to place the ring behind the headlight, and the reflector will not allow it to move.

Using the example of a video on how to make angel eyes with their own hands, readers will be convinced that this process is extremely difficult, it requires special skills, strong nerves and, of course, straight arms.

Each headlight needs to be disassembled. Manufacturers fasten their parts with a sealant, so they will have to soften it with a construction hairdryer within five to six hours. But all this will not seem such a tedious task if the headlights are not assembled on rubber sealant. In this case, there is only one way to disassemble the headlamp. To do this, you need to carefully pick out the optics and cut. This process is very long and requires attention and care. It is possible to damage the machine in the part where the body meets the glass.

Once the headlamp is removed, you need to measure the diameter of the place where the diodes or tubes will be placed. Install and fix them only on a degreased surface. How to fix it? Manufacturers of LED sets offer double-sided tape in the kit, however, it will be very hot from the lamps and it is possible that it will subsequently lose its properties. You need to use something for fixing that would provide a strong fixation and, at the same time, is resistant to heat.

When the LEDs are installed, the headlight can be assembled. In this case, you need to ensure that moisture does not get on the surface. For the connection, use a rubber sealant, and assemble with a calculation so that later, if necessary, it can be disassembled again. This is mainly required if the first assembly was made with errors and moisture gets on the headlight. This can cause the glass to fog on the inside and eventually rot the wires.

During the assembly process, you will need to connect the LEDs. There are several ways:

Connect the LEDs along with the dimensions;
Disconnect the dimensions and connect the diode tape;
Connect angel eyes along with daytime running lights;
Together with turn signals, if the tape is two-color;

Installing angel eyes with your own hands on a Prior or a car of another brand is a great temptation. But this process is extremely laborious and requires special skills. A person who is not confident in his abilities is better off entrusting the work to professionals. Moreover, after connecting the DRL together, there may be problems with turning it on and off. In this case, a special DRL controller is required. The color scheme - RGB or monochrome - does not matter in this case. The only problem you will face when installing a controller with an RGB block is finding a place to place it.

So, what should a car enthusiast remember when he wants to make himself optics in the style of angel eyes?

Do not install cheap LEDs, which after installation will not give the desired effect, and the owner will not only have to spend money on buying new ones, but also on installation;
Pay attention to the luminous flux. The ideal value for angel eyes is three hundred lumens;
Install LEDs on plexiglass or transparent plastic. This is the most common way;
Disassemble and reassemble the headlamp with the utmost care - you can damage the car body. In addition, moisture can enter the headlamp during assembly. It is necessary to preserve the ability to repeat the procedure if necessary, and remove it - otherwise the wires will rot and the glass will be cloudy.

One of the simplest options for finalizing the exterior of a car is tuning the headlights with your own hands. Today, the so-called "angel eyes" are very popular. We are talking about the luminous rings built into the front optics of the car. At first, such a solution appeared on BMW cars, but after a while many motorists liked this idea. Therefore, in this article we will try to reveal this topic and help you understand how to make angel eyes and install them yourself.

Features of Angel Eyes

The manufacture of original angel eyes is carried out using neon tubes that are bent and installed in the headlights. This mechanism uses a special ignition unit. Installing angel eyes in the headlights results in a pleasant and bright enough glow.

Some drivers use these elements as daytime running lights, as well as dimensions. It is noteworthy that angel eyes headlights can be used on various cars. Their dimensions and diameter can differ significantly from each other. Equally important is the fact that car owners can choose the optimal glow color, which will give the car a truly exclusive look.

Of course, the simplest option is to buy angel eyes and install them on one of the car services. However, many car enthusiasts want to install angel eyes with their own hands, since only in this case can you get real pleasure from finalizing your own car. And it's not at all difficult to do this. Often, angel eyes are installed on VAZ cars from the "classic" series, as well as on modern models, for example, Lada Priora. Let's move on to the question of how to install angel eyes.

LED Angel Eyes

For the manufacture of dimensions, colorless plastic sticks are used. You will need a sealant to secure the rings securely. LEDs will provide a beautiful glow. It is quite possible to make LED angel eyes on your own, even for those who do not have much experience in car tuning. For each of the rings, you need to select a pair of LEDs. In addition, 2K resistors must be purchased.

It is necessary to make a ring from each stick. To facilitate the task, you can use a jar of the appropriate diameter. We heat a plastic stick with a construction hair dryer (a simpler option is an oven) and screw it onto the selected jar. After all rings have been made, you can check them again and align if necessary.
As the name of the section implies, LED Angel Eyes involve the use of LEDs. It is necessary to determine their diameter and length, and then make the corresponding holes at the two ends of each ring. We shorten the legs of the diodes so that their length does not exceed 5 mm from the semiconductor body.
We connect the legs of the diodes to each other using a soldering iron. It is necessary to solder minus to minus and plus to plus. The plus leg is located in the thickening of the larger diameter. Next, we solder the legs of the LEDs to the wires. We advise you to use colored wires, with the help of which you will not exactly reverse the polarity.
The wire must be cut at a distance of about 15 cm, after which the ballast resistor must be soldered to it. The wire must be soldered to the second leg of the selected resistor.
The diodes are attached using a colorless nail polish. Literally one drop of the product must be applied to each of the ends. After that, you need to wait a little so that the varnish has time to dry. The varnish will provide a secure attachment of the diodes and ensure good contact between the diode and the stick. Thanks to this, LED Angel Eyes will look very beautiful.

If you have a desire to install angel eyes with "cilia", you need to make the appropriate notches, which should be present along the entire length of the sticks. Leave about 10 mm between the notches. The notches should be approximately 5 mm deep.

Angel Eyes Installation Procedure

It's time to install angel eyes headlights. To do this, you must first disassemble the headlight housing and pull out the glass. As a rule, the installation of angel eyes takes a lot of time, since the headlight must be disassembled very carefully so as not to damage the mountings.

The final assembly is also an important step. The surface of the reflector must be cleaned of dirt and debris, for which it is better to use a cotton swab. To perform this procedure, it is forbidden to use chemicals. Also, do not touch the surface with your hands.

We apply sealant to the glass and install the ring. Everything needs to be done so that the LED elements are at the top of the headlight. Next, we carry out the laying of the wires.

If there are notches on the ring, they must be directed outward. Between the headlamp and the glass, apply silicone and carefully fill all the pores. It will dry in about 30 minutes. After that, you need to test the operation of the headlights, having previously connected the power to our angel eyes.

To do this, you need to disconnect the plug for connecting the turn signals and side lights. The connectors of the turn signals and dimensions of the "Papa" type must be connected to each other, and then connected to the "Mama" of the direction indicators. As a result, you will have a free "Mom" connector, which was previously used by side lights. It is to him that the "plus" from the angelic eyes must be connected. "Minus" is connected to the turn signal mountings.

After all these actions, when the side lights are turned on, the angel eyes should also turn on the headlights. Now you know how to make angel eyes with your own hands, as well as correctly connect them to the power system.

Bi-xenon Angel Eyes Lenses

It's no secret that the best possible result is achieved only if the machine is equipped with lenses. In addition, the use of bi-xenon lenses provides a comfortable driving experience in the dark.

Thanks to such lenses, you will not blind the drivers of oncoming traffic and at the same time, you will be able to drive the car without any special difficulties. It is the bi-xenon lenses with angel eyes that look very attractive. Lenses of this kind can be mounted on different groups of lamp bases used in machines. In order to install them in the standard base, you just need to remove the outer glass of the headlight and install the lens.

Benefits of using Angel Eyes

Installing angel eyes with your own hands is one of the components of car tuning, the popularity of which is not decreasing. The modernization of the cabin and the installation of various aerodynamic elements over time are often no longer pleasing to the eye, but this option for tuning the headlights always attracts attention.

Another "plus" of using angel eyes is that they provide additional security. These optics do their main tasks well, without creating problems for other car owners. In addition, angel eyes consume a minimum amount of energy.

Photo and video of angel eyes

Probably every motorist dreams. In this case, the side lights will become similar to those that are endowed with the headlights of a modern BMW model. You can make absolutely the same spectacular lights with your own hands, since our person has ingenuity and desire. Armed with wire cutters, metal saws, pliers and other common tools, everything can be quickly organized.

In order to make "angel eyes" with your own hands, you need to find a plexiglass bar and cut four blanks out of it. LEDs are mounted in them and cuts are cut out for every 5 mm. Self-made "eyes" are installed instead of standard side lights.

Parking lights from BMW

What are Angel Eyes? It turns out that this is just another strong point from which has not left indifferent any motorist in the world. But it is not worth selling your favorite "six" and saving up for BMW only because of the peculiar and original lights. What do you think?

You can do it differently. Take the side lights of this manufacturer for a sample and try to build something similar on your own.

It should be noted right away that, no matter how beautifully and effectively these components are made, they are not welcomed by the traffic police and can cause “unhealthy” interest in the latter. But still, if you decide to go for it and become the owner of a car with such "angel eyes", you should preferably have a car with round front optics. For example, a VAZ 2106 or a VAZ 21213 has such optics. In addition, it may be some model of a foreign car, for example, the same BMW, only the old version.

Preparing

Before, you need to arm yourself with tools and the necessary material. As mentioned above, it is necessary to have pliers, pliers, a metal cutter, a file, a drill and drill of the required size, a soldering iron or a hair dryer in stock. Also important is a special transparent plexiglass or plastic rod that would withstand high temperatures. Where can I find it? Auto tuning experts advise looking for such a bar in shops specializing in the sale of curtains and blinds. In addition, do not forget to take care of the presence of a large flat capacity for a plastic rod, a round can, electrical tape, one-volt LEDs (there should be 8 of them), 220 Ohm resistors and wires with connectors.

All of the above materials and tools will be easy to find and prepare. It is important to remember that the wells in the headlights are of different diameters, which means that our "angel eyes" must be of different circumferences.

For the rod, you will have to choose the right length, although a piece of thin hose is also suitable as a yardstick (we circle the circumference of the car headlight with it). We cut off the rod of the required length and heat it up in the prepared container with a soldering iron or hairdryer until it becomes soft. If the bar is made of plexiglass, then we place it in a container with hot water so that it becomes soft.

Now you need to take the pliers and take out the workpiece. We wrap a can of coffee or something else with a blank and wait until it cools down (photo below).

If you haven't found a jar, you can use a plate instead. In this case, it will look like this:

In order to make small "angel eyes", you need to wrap the rod around the lid of the can. The smaller the workpiece, the more difficult it is to work with. Be careful not to burn your fingers.

Now we are working on a blank, from which, after cooling down on the can, a ring was obtained. A kind of niche should be drilled at the ends of each workpiece, where the LED will be installed. You need to drill very carefully, preferably at a low speed of rotation of the drill, since the walls of the twig are very thin.

On the video - do-it-yourself "angel eyes":

Further, on its outer side, you will need to cut out a couple of dozen lines with a hacksaw or drill, but no deeper than a third of the circle. This is done so that the light of our "angel eyes" is radiant.

We need to fix the diodes now. You can do this as you like, but you should take into account the high coefficient of thermal expansion of the plexiglass rod. This means that the "eyes" need to leave some free space in the niche. We take and solder the resistors to the LED legs. Two diodes must be prepared on each.

Here's what we end up with:

Go ahead and solder the LEDs to the marker lamp, remembering that you need to solder to the plus. In no case should the polarity be reversed. And all connections must be insulated with a specially designed tape. Then check how everything works.

Now it's time to dismantle the headlights. Unfortunately, there is no way without it. Then we take it out and be sure to plug the holes. We install the prepared diodes on top so that they are less conspicuous.

In conclusion, I would like to note that this is a responsible business. Supplementing the car with home-made parts is, of course, good, but you need to do it very carefully so as not to confuse something, and this is especially true for elements and parts related to electricity.

To better understand how to make "angel eyes" on the headlights of your car with your own hands, we advise you to watch this video:

We hope that the article will help you, and you will succeed!

I met a huge number of motorists who were unhappy with the installed angelic eyes, like BMWs. The second common name is "LED rings." Some shone faintly, others quickly faded out, others had a blue tint of light.

At the end of the article there will be a lot of photos of the installation on popular cars 2110, 2114, Priora, Kalina, Mazda, BMW.

1. The difference between good and bad
2. How to do it yourself
3. Installation
4. Installation examples

Distinguishing good from bad

Angel eyes of BMW, BMW serve as a standard, of course. At first, motorists will see enough of high-quality cars from expensive cars, then they want to put themselves inexpensive and prettier ones. But in the end, they get a large set of disadvantages, because they think that different models are no different. Buy the cheapest junk, on the weakest and lowest quality diodes, get the appropriate result. This is also facilitated by stores that increase prices up to 5 times.

Little LED wisdom. If you want to buy a chocolate bar, and there is only enough money for a piece of gamna, then it is better to save up for a chocolate bar.

There is no need to buy cheap ones, they will quickly fail. To replace it with others, you will have to disassemble and assemble the headlight every time. If you don't do it yourself, then this work also costs decent money. You will need a new pack of headlight sealant every time. After calculating all the costs, you will see that it is better to put good ones for a long time.

Ready-made sets of LED angel eyes for a particular car brand, for example, Mazda 3, are sold on Aliexpress. The price for such products is quite high, 3-5 times higher, they write like a copy of the branded ones. But as practice shows, the quality is low, the assembly is poor, and they break down quickly. It is often necessary to advise readers on how to proceed in such a case. There are usually two options, replacing multiple LEDs or replacing the entire LED ring.

To make it clearer, look at the difference in the characteristics of Chinese and branded LEDs 5050, 5630, 5730, 3528. The Chinese put a crystal 3-4 times weaker in a standard case, and 10 times worse in quality. It is difficult to distinguish good from low-quality ones, they are outwardly the same, it is necessary to calculate the power of one LED. Many online stores cannot resist the temptation to sell a cheap product worth 100 rubles for 1000 rubles.

How to do it yourself

Readers of my site are interested in how to make angel eyes with their own hands, after the current reading of articles on the Internet. According to statistics, 99% are faced with this for the first time and mostly want to save money. They do not know the standards for luminous intensity and other parameters; therefore, a not very good result is obtained.

As a light source, you can use an end (corner) LED strip or an ordinary flat one.

On the Internet, the most popular option for making LED angel eyes with your own hands from transparent plexiglass or plastic. Shallow recesses are applied to it, and 0.2 or 0.5 Watt LEDs are inserted from the ends. As you can imagine, the power is too low, the light will scatter forward and inward, and decrease inside the transparent material. Such an LED ring will be fully visible only at night, the brightness is at the level of the usual size. Even powerful LED diodes of 1W, 3W, 5W will not help.

In order not to break the textolite, first cut out the circle and then remove the middle. Make the conductive tracks and it remains to solder the LED. This method is quite costly in terms of time and materials. For comparison, the cheapest diode ring for 20 LEDs costs from 80 rubles on Aliexpress, shipping is already included with the price.

For it to shine at the level of a prestigious car, a power of 5-10 watts and a luminous flux of 300 lumens are required, and the light must only go forward.

Another way is to use a flexible light tube, which is most often inserted into headlights as side lights. The tube can be cut and made a ring, it will keep its shape due to contact with the reflector. The two-color tube will be able to perform the function of dimensions and turn signals.

Installation

Do-it-yourself installation of angel eyes is quite difficult, skill is required, sometimes good nerves. For installation, disassembly of each headlight is required. Most of the headlights are assembled on a sealant, which softens when heated with a building hairdryer. Much less common on a sealant that is rubber. It does not melt or soften in any way; you have to carefully pick it out and cut it for several hours. One headlamp can take from 1 to 5 hours. The first time it took me about 10 hours to parse. Due to inexperience, you can spoil the presentation in the area of \ u200b \ u200bthe junction of the glass and the case.

Then the diameter of the seat is measured and the angel eyes are installed. Degrease the gluing points and fix the parts. The kit often comes with double-sided tape for installation, but I don't trust him. The halogen low beam bulb in the headlight gets very hot and affects this tape.

In the reverse order, assemble the headlamp using a special rubber sealant. Assemble so that you can disassemble without consequences next time. If you collect it badly, moisture will get inside, the headlight will sweat, the wires will rot.

There are several connection options in the headlamp:

inclusion together with dimensions;
instead of side lights;
together with DRL;
inclusion of two-color along with a turn signal;

If the connection to the dimensions does not suit you, to control the on and off, you can use the controller for the daytime running lights of the DRL. Search for "DRL controller". To connect RGB, single-color schemes are suitable, you just have to look for a place to place the RGB control unit.

If you are not confident in your abilities and do not have enough experience, it is better to contact a specialist auto electrician.

Installation examples

The leaders in installation are domestic cars VAZ 2114, VAZ 2110, Priora. Among foreign cars BMW, Mazda 3, BMW E39, Ford Focus. They are also actively installed on motor vehicles, scooters, motorcycles, ATVs.

VAZ 2114

Among domestic cars, the second place in popularity is occupied by angel eyes on the VAZ 2114, the first place is shared by Priors and VAZ 2106, which have a round reflector shape.

VAZ 2110

Kalina VAZ

Mazda 3, 6 Mazda 3, 6

Among imported cars, angel eyes for Mazda 3, Mazda 3. They look especially gorgeous on the Mazda 6, which has 4 circles in each headlight. It will be interesting to look at RGB LED rings, which will complement the dimensions and turn signal.

Priora VAZ 2170

The most popular option in Russia is the Prioru Angel Eyes. The shape of the headlights is well suited for such tuning, the reflectors are round in shape.