Repair of gas water heaters and boilers. Repair of boilers and boiler equipment Repair and maintenance of household gas boilers

Modern gas boilers are quite complex technological equipment. With proper care and proper handling, the gas boiler will serve for a long time without any failures. However, even the most expensive and functional equipment has its own resource, after which all kinds of malfunctions begin to appear.

Knowing the main causes of malfunctions and the procedure for eliminating them, you can repair your gas boiler with your own hands. This is a very painstaking, responsible, but in most cases relatively simple job.

First of all, it is necessary to establish why any malfunctions may occur in the operation of gas heating boilers. A number of different factors can lead to problems.

Electricity

Modern gas boilers are equipped with various automation equipment. These funds, in turn, are powered by electricity. And, despite the fact that the 21st century is already in the yard and systems for the use of alternative energy sources are being actively developed all over the world, the problem of stability of power grids remains relevant for many regions, especially for remote villages and all kinds of summer cottages.

A sudden blackout or a strong surge in electricity is one of the main enemies of any modern gas boiler.

To avoid all the accompanying troubles, buy a quality stabilizer in advance. Do not spare money to buy this device - there is little sense from cheap models, so it is better to immediately allocate funds to purchase a good stabilizer from a well-known manufacturer. Be sure that in the event of a breakdown of the automation, you will spend much more money on its repair and replacement.

Water

At home, wall-mounted models of gas boilers are often used. Such devices are simultaneously responsible for both space heating and hot water preparation.

The design of wall-hung boilers includes a flow-through heat exchanger. Low-quality hard water with various impurities is the main enemy of the heat exchanger of a gas boiler. At the same time, under the influence of low-quality water, the heat exchanger can fail in just one season.

To prevent such damage, install special filters. The best option is a complete water purification system. With it, your boiler will work as long as possible, and using purified water is much safer for health.

Installation errors

Any knowledgeable person will tell you: only qualified specialists should deal with the installation and piping of gas heating equipment.

Even the slightest mistakes at the stages of installation and connection of equipment can lead to irreversible consequences. For example, improper piping in the case of a cast-iron gas boiler more powerful than 50 kW will lead to the fact that at low temperatures the unit will simply split.

Therefore, if you are not an experienced gas operator, entrust the installation of the boiler to professionals - this way you will save yourself from many problems in the future.

Weather

Unfavorable weather conditions can also lead to many different problems. In frosty winters, people turn on heating at almost full capacity. This leads to a significant decrease in pressure in the gas pipeline system. As a result, boilers cannot fully realize their potential.

You will not be able to solve this problem on your own - you still cannot explain to your neighbors that by their actions they only aggravate the situation. As a solution to the problem, you can install an additional boiler operating on a different fuel.

Should you repair the boiler yourself?

A modern gas boiler is a complex and potentially dangerous system. The main danger of such units is the risk of gas explosion in the event of improper handling of the equipment or untimely elimination of various problems.

Various kinds of automation are responsible for maintaining the operation of the gas boiler at an optimal level. An inexperienced user is often unable to understand its device. Therefore, it is better to immediately invite specialists to troubleshoot serious problems.

On your own, you can try to eliminate only visible damage and various contaminants that have led to the failure of the pipe, chimney and other parts of the boiler.

There are a number of typical problems that you can fix yourself in most cases. Problems will also be listed, in the event of which you can only protect yourself before the arrival of a specialist.

If a distinct smell of gas or smoke appears in the room, immediately turn off the boiler and leave the room, opening it for ventilation.

Get a professional immediately. Trying to solve the gas leak problem yourself without the necessary skills is extremely dangerous and unreasonable.

Combustion sensor breakage

If the flame sensor or the gas supply pipe breaks down, turn off the boiler, close all gas valves and let the unit cool down completely.

Return to the area after a while to check for the smell of gas. If everything is in order with the draft, try to turn on the boiler again. If there is no thrust, immediately call a repairman.

Boiler overheating

Overheating is one of the most common problems in modern gas boilers. The reason for this may be a malfunction of the automation equipment or a clogged heat exchanger.

It is impossible to cope with the repair of automation without the appropriate knowledge.

You can also clean the heat exchanger with your own hands. The most common materials for the manufacture of heat exchangers are copper and stainless steel. There is usually no problem cleaning them, but be extremely careful anyway.

To clean the heat exchanger, simply remove it and thoroughly clean it with a metal brush. In the case of a copper heat exchanger, it is best to replace the brush with a metal sponge used for washing dishes.

Blower fan malfunctions

The problematic place of fans is their bearings. If your boiler fan stops developing the set number of revolutions, try to eliminate the problem as soon as possible.

To do this, remove the back of the fan, remove the stator and lubricate the bearings. Machine oil is fine for lubrication, but if possible it is best to use a higher quality carbon compound with heat-resistant properties.

An interturn short circuit can also lead to problems with the fan. Only a specialist can cope with the elimination of this malfunction. Return the stator for repair to replace the winding, or immediately replace the faulty unit with a new device.

Chimney problems

Often, excessive clogging of the coaxial chimney leads to the appearance of various malfunctions in the operation of a gas heating boiler.

Remove the chimney and thoroughly clean all of its components from soot. In this way, you will not only restore the previous level of efficiency of the unit, but also significantly increase the efficiency of the boiler.

ETEK LLC is an authorized service center for the repair of gas boilers. We are an official dealer of most manufacturers of heating equipment, such as: Baxi, Bosch, Buderus, De Dietrich, Ferroli, Viessmann, Wolf, etc. All personnel of our Service Center are regularly certified by these manufacturers.

We provide round-the-clock urgent repairs of gas boilers, heating systems and utilities in Moscow and the Moscow region, as well as in other regions. We have our own warehouse, where a wide range of spare parts is presented

Service cost

Price list for the departure of the service team and basic diagnostic work:

The detailed cost of all measures for repair, service, expansion and installation of your heating system can be found in the price section.

The main causes of breakdown

Incorrect piping can cause serious damage to the entire system. Water treatment also has a great influence - if the water used is not filtered, then the heat exchanger and pipes of the heating system can become clogged. But the most dangerous thing is bad wiring, which can provoke automatic failures and even cause the boiler to explode at the slightest gas leak.

Details of our work:

As a rule, minor breakdowns and equipment failures are typical cases that are well known to our specialists. Usually, everything can be corrected by proper calibration of automation or by replacing worn out units. All this is done at the first visit of specialists right on the spot, the teams always have with them a set of in-demand spare parts for repairing gas boilers at home.

Sometimes it is not possible to cope with the problem on its own: for example, Wolf gas boilers of the GU series are turned off with an error on the display of flue gas output - i.e. the normal part of the boiler cycle is indicated as an error. Therefore, it is important to read the user manual. The occurrence of malfunctions is signaled by the built-in security system, which displays the number of the corresponding error on the display. Equipment manufacturers recommend contacting the service center if, after restarting the boiler, it stops again. In cases where it is not possible to solve the problem on your own, we recommend that you contact us for help. We will help you repair a gas boiler quickly and efficiently, right at your home.

Our Service Center offers a full range of services for the maintenance and repair of gas boilers directly at the facilities:

• Regular maintenance of gas boilers at home anywhere in Moscow and the Moscow region. During the operation of boiler equipment, a number of malfunctions arise, many of which can only be detected by boiler maintenance specialists.
• Checking the connection and installation diagram of the gas boiler for compliance with the manufacturer's recommendations and technical standards.
• Diagnostics of boiler malfunctions and elimination of their causes.
• Repair and / or replacement of faulty parts.
• Cleaning the boiler, burner, magnesium anode and other working surfaces if necessary.
• Gas boiler control board repair.
• Boiler start-up after repair, conservation or maintenance.
• Setting up the boiler automation and balancing the gas flow to achieve optimal performance.
• Control measurements of the air composition in the boiler room and in the exhaust gases using a high-precision gas analyzer (expert analysis of the content of CO, CO2, methane, propane-butane).
• Any other work that may be required to ensure trouble-free and efficient operation of your boiler room at a convenient time for you at home.

It is also important to remember:

The main element of a gas boiler is the burner, which ensures the efficiency of fuel combustion. During the operation of the equipment, deposits of combustion products accumulate on the working surfaces, which leads to a decrease in the efficiency of the burner. Ignition reliability and combustion stability decrease. Fuel consumption increases and carbon monoxide production increases. Cleaning during service of gas boilers and timely replacement of spare parts helps to avoid this. If this is not done, the working surfaces of the boiler fail - cracks and ruptures appear, which, as a result, will lead to a serious accident.

After repairing a gas boiler, it is necessary to adjust the equipment so that the technician does not start work unbalanced and does not receive an emergency load. Further service support, which is the guarantee of the stability of any boiler house, we are ready to undertake in full.

Our service center works around the clock and seven days a week, for your convenience, you can fill out an online application for the repair of gas boilers - on our website or by calling the indicated numbers at any time convenient for you 24/7. Departure of the master on the day of treatment!

By contacting one of our specialists, you will ensure the creation of a comfortable temperature regime in your home, which will make your life more comfortable.

Why is it worth contacting a professional craftsman?

A feature of our company is a focus on high results, the achievement of which is facilitated by the efforts of experienced employees and the use of modern equipment. Our boiler repairmen from the Komplex Ideas company operate successfully and efficiently even in emergency conditions in production. Using the services of our specialists will allow you to:

• Stabilize the operation of gas equipment.
• Quickly eliminate breakdowns of any level of complexity.
• Improve your equipment operation skills.
• Observe the slightest signs of boiler malfunction.
• Correctly act in case of problems.

Our gas boiler specialists are distinguished by their attentive attitude to the customer's problem, professionalism and competence, consistency. All this best characterizes the quality of their work. The specialists of our company are equipped with all the necessary equipment for a successful repair.

When should a master be called?

Often the owner of a gas boiler is not able to independently figure out the cause and nature of the breakdown. In this case, it is better to contact our service company and call a repairman for gas boilers, who will promptly and efficiently eliminate the malfunction. There are indirect signs indicating the need to call a professional:

• The boiler was damaged.
• The case is constantly heated.
• The equipment cannot cope with water heating or heating.
• Often shuts down by itself.
• When the pump is running, extraneous sounds are heard.

It should be noted that high-quality repair of a gas boiler is only possible for a qualified specialist, because it includes many complex operations that require professional skill and the use of special tools.

What does professional repair include?

• Departure of the master to the object.
• Diagnostics.
• Elimination of breakage.
• Test start-up and equipment adjustment.
• Setting up automation parameters.
• Hydraulic tests.
• Drawing up an act on the implementation of repairs.

To maintain the efficiency of the gas boiler, its repair should be trusted only by professional craftsmen. High-quality repair work will extend the life of the equipment and make it more economical. In our service company "Set of Ideas" you can order a major overhaul of your heating equipment by our best craftsmen. They will promptly come to your aid and efficiently eliminate all breakdowns of your equipment.

You can call a specialist to solve your problem. Fill out the form, briefly describe your problem and we will call you back for consultation.

Prices

• Service Price
• Departure of the engineer during working hours from 8:00 to 22:00
• Within a small concrete ring 2000 RUB
• Tariff when going to the object outside the small concrete ring, per km. round trip RUB 30
• Departure on holidays × 1.5
• Check out after hours from 22:00 to 8:00 am × 2
• Diagnostics
• Fault diagnosis (up to 2 working hours) 2000 RUB
• Fault diagnosis (more than 2 working hours) RUB 1,500 in hour
• Replacement / installation of gas and fuel fittings and devices
• Cleaning, replacing the electrode with setting gaps 1000-2000 rub.
• Cleaning, replacing the photocell 1000-2000 rub.
• Replacing the control box, combustion manager 1000-2000 rub.
• Fan replacement RUB 1500-3000
• Replacing the burner actuator (without adjustment) 3000-5000 rub.
• Replacing the transformer 3000-4000 rub.
• Replacing the nozzle from 3000 rubles.
• Replacing the fuel filter from 5000 rub.
• Replacing the diesel burner fuel pump from 5000 rub.
• Fuel level sensor installation
• Bleeding the fuel line
• Replacement / installation of water fittings and devices
• Circulating pump from 3000 rub.
• Pump group from 3000 rubles.
• Heating system make-up with a pump from 1500 rubles.
• Security groups from 3000 rub.
• Automatic air vent from 2000 rub.
• Mixer servo RUB 3000
• Distributor comb from 5000 rub.
• Installing a coarse filter from 4000 rub.
• Cleaning the coarse filter from 600 rubles.
• Repackaging the engineering system for 1 point from 3500 rub.
• Replacing the wall-mounted boiler pump from 3000 rub.
• Replacing the primary heat exchanger of the wall-hung boiler from 4000 rub.
• Replacing the wall-mounted boiler secondary heat exchanger from 4000 rub.
• General
• Repair, replacement, installation and commissioning of automation
• Replacing the electronic board RUB 3000
• Replacing the control panel from 3000 rub.
• Replacing the thermostat 3000-5000 rub.
• Replacing the thermocouple from 3000-5000 rub.
• Replacing the thermostat 2000 RUB
• Installation, commissioning of weather-independent automation from 7500 rub.
• Installation, commissioning of weather-dependent automation up to 3 heating circuits from 7500 rub.
• Installation, commissioning of weather-dependent automation up to 5 heating circuits from 8500 rub.
• Assembling the controller from 6000 rub.
• Setting up weather-independent automation from 5000 rub.
• Setting weather-dependent automation from 5000 rub.
• Connecting an additional boiler automation module from 3500 rub.
• Installation of outside temperature sensor, room regulator (excluding cable installation) 2000 RUB
• Installing the line temperature sensor RUB 1000
• Installing the flue gas temperature sensor RUB 1000
• Installing the overturning draft sensor from 1000 rubles.
• Installing the boiler body temperature sensor from 1000 rubles.
• Installing the boiler sensor from 2500 rubles.
• Installing and configuring the servo from 2500 rubles.
• Installation and connection of relay contactor from 2500 rubles.
• Installation of an additional automation module from 3500 rub.
• Replacing an additional automation module similar to the one installed from 2000 rub.
• Replacing an additional automation module that is not the same as the one installed from 2500 rubles.

Urgent repair of a gas boiler at home is one of the most demanded services in our company.

Proper and uninterrupted operation of the gas boiler makes your home cozy and warm. Timely maintenance and repair of such equipment will help you avoid more serious problems.

Most often, the repair of a gas heating boiler may be required:

• Due to constant power surges. Power surges and unplanned power outages disrupt the operation of the heater.
• When using hard water with impurities. Alas, in the Moscow region the water quality is poor.
• Due to improper operation and untimely service

The TermoStream specialists will help you understand the cause of the breakdown, perform a comprehensive equipment diagnostics and repair it. Given the complexity of such work, we advise you not to try to solve the problem yourself, but to turn to professionals.

The TermoStream masters have extensive experience and modern equipment. This allows us to carry out urgent repairs of gas boilers in Moscow and the Moscow region without dismantling the boiler and checking it in a service center. In most cases, inspection, diagnostics and repairs are carried out right at your home.

We are an authorized service center:

Prices (includes departure, diagnostics, repairs):

	Wall-hung and condensing gas boilers up to 40kW, Floor standing gas boilers up to 65kW.	Cost, rub.
	Commissioning works. For each additional boiler in the boiler system + 50%.
	Cleaning the combustion chamber from soot deposits (added to the cost of repair / maintenance work)
	Condensing wall mounted gas boilers from 45 to 80 kW, Condensing floor standing gas boilers up to 80 kW, Traditional floor standing gas boilers from 65 to 300 kW	Cost, rub.
	Repair / maintenance with a guarantee for the work performed and installed spare parts for 6 months. For each additional boiler in the boiler system + 50%.
	Commissioning. For each additional boiler in the boiler system + 50% ..
	Conversion to liquefied gas without the cost of spare parts	Included in the cost of commissioning
	Cleaning the combustion chamber from soot deposits (added to the cost of repair / maintenance of the boiler)
	The cost of repair / maintenance of boilers over 300 kW	by agreement
	Condensing wall mounted gas boilers from 80 to 300 kW, Condensing floor standing gas boilers from 80 to 300 kW	Cost, rub.
	Repair / maintenance with a guarantee for the work performed and installed spare parts for 6 months. For each additional boiler in the boiler system + 50%.	11 000
	Commissioning of a condensing gas boiler. For each additional boiler in the boiler system + 50%

Note:

1. The cost of work on objects located from the Moscow Ring Road in the area from 50 to 100 km increases by 10%.
2. The cost of work on objects located from the Moscow Ring Road in an area over 100 within the boundaries of the Moscow region increases by 20%
3. Boiler block assembly, section replacement:
   • Protherm (low power) - 13,500 rubles.
   • Viessmann, Vaillant up to 63 kW - 16 500 rubles.
   • Viessmann, Vaillant, Protherm from 65 kW to 160 kW - 22,000 rubles. (high power by agreement).

This website is for informational purposes only and under no circumstances is a public offer determined by the provisions of Article 437 (2) of the Civil Code of the Russian Federation.

A specialized heating service center of an engineering company has technical departments throughout the Moscow region. We have been carrying out qualified repair and maintenance of a gas boiler, boiler equipment at facilities in Moscow and the Moscow region for more than 20 years! Maintenance and repair of gas heating boilers in private houses is always carried out professionally, with high quality with a guarantee for work and replaced spare parts. The emergency service on duty works around the clock and every day to eliminate boiler equipment accidents at serviced facilities in the Moscow region. Polite specialists are always ready for technical support of gas boiler houses in emergency situations when heating in a cottage and a gas boiler house of an enterprise is stopped during the heating season. Urgent repairs of heating boilers are carried out at uniform prices, which also refer to a one-time visit of a service technician to the house to repair gas equipment in the boiler room of a residential building.

We carry out the repair of gas equipment professionally, quickly and efficiently. Service engineers have vast experience, they constantly undergo training and refresher courses in special factories. Availability of professional diagnostic and repair equipment for servicing gas boilers of any capacity allows us to perform repairs at the highest level. This is our daily work that must be 100% implemented.

Within a few minutes after submitting the application to the engineer on duty, a free service engineer working in the subdivision of the service center in your area will contact you to clarify the nuances of arriving at the house and repairing the gas boiler.

The cost of a removal specialist's departure (payment for mileage) is estimated at 15 rubles / km from the Moscow Ring Road in December 2014 (the price per mileage is constantly being adjusted, please check the cost of work with the engineer on duty). When replacing a boiler, finances paid for a set of measures for diagnosing heating equipment in a residential building are then included in the total payment for work, equipment, spare parts when replacing a gas apparatus at home. To replace the gas boiler AOGV, a full range of organizational and technical measures is carried out, and if necessary, all documents are drawn up according to the list of the local branch of Mosoblgaz (gas trust).

All questions of interest to you about the repair of a gas boiler, the cost of repair work, please specify at the current time by calling the engineering service on duty

A service engineer accepts information to identify a malfunction of a gas heater and organize urgent repairs of equipment in a private house or a gas boiler house of a commercial enterprise.

Data for your application for the repair of a gas boiler in a cottage:

• manufacturer and model of gas boiler (abbreviation in letters and numbers);
• gas apparatus power;
• if there is a blower burner, indicate its model;
• about a malfunction (if there is a self-diagnosis, indicate the error code);
• photographs and video materials upon request of a service engineer;
• the serial number of the gas boiler (desirable);
• postal address (the location of the object is required);
• free telephone line number for contacting the user.

In an emergency, pay close attention to the recommendations of the technical service engineer on duty. Urgent emergency repairs of gas boilers are carried out according to the accelerated organization of service. Polite specialists of our company work to provide technical support in winter and summer around the clock, paying attention to each customer.

We wish everyone peace and warmth in your homes!

• The right start is the key to the efficiency of boiler repair in a private house.
• What malfunctions are addressed by the owners of heaters in the Moscow region.
• Calling a service center master for urgent repair of a gas boiler.
• Emergency repair of the Buderus wall gas apparatus.

Maintenance of a gas boiler in a residential building under an annual contract

gas floor (wall) boilers after gasification of the facility, when the contract is concluded for the commissioning of your gas facilities, is carried out with commissioning according to the plan of the contractual terms of both parties. After the conclusion of the contract for the commissioning and maintenance of the gas boiler, the validity period is one year, during which the owner of the gas boiler counts on maintenance if a master is needed to adjust the heating.

When organizing installation work for heating equipment in your residential building, a comprehensive contract is drawn up for the installation and commissioning of heating devices, at the same time, commissioning and maintenance of the gas boiler are performed subject to the service guarantee for the entrusted equipment. Preventive work for gas boilers and heating systems is best carried out by prior request, having agreed on all types of maintenance in the summer, which is always convenient and cheap for the customer of the technical service.

Service center for the repair of gas boilers

Our company has been performing the first start-up of the gas apparatus, installation and maintenance work for any heating equipment on a professional basis for more than 20 years!

Specialized technical units of the center work with many foreign manufacturers of gas heating equipment, such as Protherm and Thermona, Vaillant and De Dietrich, AEG and ACV, BAXI, Beretta and Bosch, as well as the German Buderus plant, which is setting up the production of diesel and gas boilers in Russia.

The excellent quality of maintenance and post-warranty service of gas boilers CTC and Dakon, Demrad (discontinued) and Duval, Electrolux and Ferroli, Junkers, Lamborghini and Mora make our company one of the leaders in this industry. The team of specialists is proud and loves their work. We constantly take into account the requests and wishes of the owners of South Korean double-circuit heaters Kiturami and Rinnai, Arderia and Navien, as well as high-quality German heating equipment Wolf and Viessmann (we note the excellent supply of spare parts and accessories).

Russian gas boilers Don, Siberia, KChM, Ishma, AOGV, AKGV (ZhMZ), Neva Lux and Thermotekhnik (special offer) have technical support since the entry into the market of climatic equipment for everyday life. Today, Russian gas boilers have once again proven their advantages in reliability and the best performance for uninterrupted operation in the harsh winter, when heating must be comfortable and without stopping for repairs.

Service repair applies to heat exchangers of floor and wall gas boilers of the specified manufacturers, due to the fault of the production. If the warranty card is correctly drawn up and commissioned by the company's service engineer, then a free replacement of the spare part is guaranteed. The first start-up of a gas boiler in a private house, be sure to order from an authorized service company, a representative of the manufacturer of the brand of your device.

Repair of imported heat exchangers can be accompanied by ordering the required equipment and its long-term delivery from abroad. Winged - “abroad will help us” may not be entirely relevant for many reasons on the way of spare parts to Russia, in particular to Moscow and the region. In this simple competition, the domestic heating equipment (Zhukovsky, Borinsky, Rostov Heating Boiler Plant) has been constantly winning over the past 20 years, which introduce both Russian and European control and safety automation (Honeywell, SIT 820 NOVA, etc.) the supply of which is difficult to disrupt and stop. These are not cast-iron heat exchangers of floor-standing boilers, gas valves and automation units - these are highly intelligent parts of heating boilers dozens, hundreds of times smaller than metal heat exchangers of heating units.

If the heat exchanger has not been subjected to freezing with a water coolant, then chemical washing of the internal body of the heat exchanger will bring it into working condition and leave the ideal formula for flow and heat transfer. Heat exchangers for the repair of gas boilers of domestic production, such as Neva Lux, ISHMA, AOGV, AKGV, DON, SIBERIA, KChM, ZOTA are always available, the repair of such gas boilers is carried out quickly and efficiently.

In order to avoid unpleasant situations associated with the repair of a gas boiler heat exchanger, we recommend that you do annual chemical flushing of steel heat exchangers and the entire heating system in a private house, which leads not only to the safety of the heat exchange unit, but also to an increase in heat transfer in the heating system and, as a consequence, saving finances and resources boiler. With high-quality maintenance and proper organization (boiler piping) of heating, gas appliances provide the desired heat exchange and are operated for decades without overhaul.

Repair of boiler control boards

for wall and floor gas (diesel) heating boilers, both double-circuit and single-circuit devices, is carried out after diagnostics of heating equipment at home. A detailed analysis of the operating conditions of the boiler and the examination of external signs of a board malfunction is sufficient for a clear identification of problems and further troubleshooting. We service electronic control and units of gas boilers of imported and Russian production.

The owners of European wall-mounted double-circuit heaters are increasingly proposing to repair and restore the control board, rather than install a new electronic unit on their boiler. Why is this initiative taking place?

1. Repairing an old board of any boiler unit is always cheap relative to replacing a faulty one with a new control board.
2. In the course of diagnostics, obvious causes and sources of failure of the control unit of the heater are identified.
3. Correcting faults in the boiler boards brings a clear understanding of a qualified repair during the working condition of the heating boiler and maintaining the warranty for the work performed, as well as replaced spare parts.

The presence of an electric current voltage stabilizer (safety devices) for a gas hinged boiler (other types of boilers) - there is a special condition for the operation of devices with a correct electrical connection. The electrical characteristics recommended by the manufacturer of hot water equipment during commissioning (first start-up) of the apparatus, of course, must be constant and controlled.

The absence of a stabilizing device makes it more likely that a voltage drop in the mains will make the electronics unusable. The presence of a stabilizer does not always mean a stable voltage at the input to the control automation of a gas boiler, since the technique of this kind of stabilization is different in its technical parameters and quality purpose.

During the diagnosis of the boiler, it is worth checking the stabilizer under load, identifying its limits (lower and upper) for the gas control board. But in any case, diagnostics and repair of the gas boiler control board is inexpensive, if you compare such a repair of the unit with the replacement with a new electronic board, the money saving is very significant!

Many workshops for the repair of gas boilers of well-known manufacturers, such as Wisman, Buderus, Vailant, Proterm, Baksi, Ferroli and Thermona (Term) offer replacements for electronic control boards and automation. In this case, the maintainability of electronic boards is an issue under discussion towards the official replacement of the board. New spare parts are always in stock at the official dealers of this heating equipment.

And what should users do if the model is out of production, for example, some models of wall-mounted boilers SAUNIER DUVAL, HERMAN, JUNKERS, UNITHERM. The supply of parts, including boards to the Russian market for these boilers has ceased, but they are in excellent condition and the owners do not want to part with them? So what if you need a boiler electronics, heat exchanger or three-way valve?

We repair any electronic control boards for gas boilers, restore heat exchangers and flow parts by chemical washing. With these questions, please contact our service center, we will certainly help you in solving these problems, the repair of gas boilers of this kind is difficult, but quite feasible.

Repair of Russian gas boilers

The main direction of our company's practice is the repair and maintenance of gas boilers of domestic production, that is, gas heating and water heating equipment of Russian manufacturers and factories of the EurAsEC countries. These include factories with extensive experience in the production of gas heating devices, as well as original spare parts for the assembly and repair of these heating devices.

ISHMA of the Lipetsk Borinsky manufacturer is well supplied with parts and spare parts for the repair of this gas equipment. For example, a heat exchanger for replacement in a gas boiler ISHMA-40 is produced at the plant within two working days, the heat exchanger is made to order.

Zhukovsky Machine-Building Plant ZhMZ produces high-quality gas boilers today with Italian and German automatic controls, which perfectly affects the operation of the units and are presented at a real price in Moscow and throughout Russia. Zhukovsky gas boilers AOGV-11.6-3; AKGV-11.6-3; AOGV-17.4-3; AKGV-17.4-3; AOGV-29-3; AKGV-29-3; KOV-SG-43; KOV-SG-50; KOV-G-68, which for many decades have been in great demand among the population of the Russian Federation, both among the owners of private houses and for gas boiler houses of small enterprises.

The Siberian manufacturer of equipment Zota is among the best proposals for boilers operating on gaseous and other fuels in country houses. Rostov gas boilers Don have always been maintainable and easy to operate, spare parts for these boilers have not changed for several decades. The old model of universal combined boilers Don of the Konord plant in Rostov-on-Don was discontinued, but it was replaced by a new modification of the heater with a cast-iron heat exchanger.

In recent years, wall-mounted gas boilers Neva Lux of the St. Petersburg supplier of modern heating equipment have been in great demand among owners of apartments, private houses, boiler enterprises. Repair of gas wall-hung boilers Neva Lux always takes place at a high professional level, taking into account the excellent service provision with spare parts for repairing Russian boilers Neva Lux. Carefully follow the information on the Neva Lux boilers, you will learn about all changes and supplies of equipment in your region in the office of the company in real time.

In 2018, the list of serviced domestic heating equipment on gas is as follows:

EuroTherm (Kursk)

NevaLux (St. Petersburg)

Ishma AOGV (Borinskoe)

AOGV (AKGV) ZhMZ (Zhukovsky)

Siberia plant Rostovgazoapparat

Don Conord (Rostov-on-Don)

Thermotechnician (Moscow)

Taiga (Moscow)

Hearth (Ulyanovsk)

ZOTA (Krasnoyarsk)

KCHM (Kirovsk)

Pechkin KSG (Taganrog)

and other gas boilers from Russian manufacturing plants.

Russian gas boilers - repair and maintenance in the Moscow region and Moscow:

• Repair and maintenance of wall-mounted boilers Neva Lux is the specialization of our service center in the Moscow region and Moscow. We offer installation, commissioning of a wall-mounted gas-fired device, its connection to a gas supply system, a coaxial chimney, as well as pipes of the heating system and hot water supply in a private house.

Gas settings for safety automation, adjustment of heating circuits in a country house are performed by masters after a call from the company's dispatch service. Repair of electronic control boards for gas boilers Neva Lux, testing of the electrical and electronic circuit of wall-mounted heating units Neva Lux in the Moscow Region can be ordered to any resident, even from remote areas of the Moscow Region. Repair and annual maintenance, as well as one-time visits of specialists from a single service center for repair and commissioning work for heating equipment in New Moscow and the Moscow region.

• Repair and maintenance of gas boilers ISHMA. Diagnostics, repair and service of Ishma heat exchangers, not excluding the order of a new part and its replacement. Ishma gas boiler leaking? Is the pressure in the heating system with Borinsky heater falling? Ishma unit shuts down on its own, knocks and clicks inside when heated? Contact our Moscow service for the repair of household gas boilers, our masters are always ready to provide technical support to every resident of the near and distant Moscow region.

Repair and replacement of Ishma gas boilers are carried out at a high professional level to the working condition of the equipment in the cottage. Spare parts and components for Ishma devices are always available in stock and provided as part of maintenance with a guarantee. We eliminate complex malfunctions of non-volatile boilers Ishma, when the heater does not start for a long time or goes out for no apparent reason.

Foreign gas boilers - maintenance and repair in Moscow and the Moscow region:

* The presented brands of heaters are serviced subject to valid availability of spare parts in the Russian Federation!

• Repair of German gas boilers VAILLANT Vailant
• Repair and maintenance of a gas boiler from Slovakia PROTHERM Proterm
• Repair and adjustment of Slovak boilers ALPHATHERM Alfatherm
• Repair of gas boilers according to German technology BUDERUS Buderus
• Repair of gas boilers ARISTON Ariston
• Repair of gas boilers BERETTA Beretta
• Repair of gas boilers AEG AEG
• Repair of gas boilers JUNKERS Junkers
• Repair of gas boilers MORA Mora
• Repair of gas boilers ARDERIA Arderia
• Repair of gas boilers HERMAN Herman Spare parts for the boiler are available in stock!
• Repair of gas boilers KITURAMI Kiturami
• Repair of the gas boiler ROCA Roca out of production!
• Repair of gas boilers DEMRAD Demrad out of production!
• Repair of gas boilers LAMBORGHINI Lamborghini
• Repair of gas boilers CHAFFOTEAUX Shafoto Shafote
• Repair of gas boilers WOLF Wolf
• Repair of gas boilers from France FRISQUET Friske
• Repair of the gas model HERMANN HABITAT Herman Habitat 2 is out of production!
• Repair of the gas boiler VIADRUS Viadrus
• Repair of the Polish gas boiler TERMET Termet
• Repair of the French boiler SAUNIER DUVAL Senor Duval Spare parts available and on order!
• Repair of gas boilers IMMERGAS Imergaz
• Repair of gas boilers technology Germany-Japan KENTATSU FURST
• Repair of gas floor boilers RAPIDO
• Repair of gas floor boilers SIME (Syme) Italy
• Repair of gas boilers ATTACK

*** For spare parts for boilers discontinued in Europe, please call

the emergency dispatch service of the engineering company at the current time! Many original spare parts on order with a realistic delivery possibility.

Gas boiler repair Neva Lux

We repair the gas boiler Neva Lux at the request of the user of this gas appliance. A request to call a Neva Lux gas equipment repair specialist is made through the company's office or by calling the technical duty shift outside of working hours. As representatives of the Gazbalt company, which produces gas wall-mounted boilers and gas water heaters Neva Lux, we carry out a clear and well-functioning mechanism of actions for the repair of gas equipment Neva Lux.

We respond to every customer request on the day of contact, we repair the gas boiler, minimize the cost of additional spare parts, parts, equipment. Today our company offers repair services for gas wall-mounted boilers Neva Lux of the following models: Nevalux-8230, Nevalux-8230-1, Nevalux-8624, Nevalux-7211, Nevalux-7218, Nevalux-7224, Nevalux-8618, Nevalux-8224, Nevalux -8224-1. The list of work on the repair of the gas boiler Neva Lux includes the following technical measures:

• repair of the fan control system - replacement of the air pressure switch for Neva Lux gas boilers;
• replacement (repair) of the fan of the Neva Lux boiler to ensure the forced removal of exhaust gases;
• replacement of the heating temperature sensor, correction of faults in the heating circuit of the wall-mounted boiler Neva Lux;
• replacement of the flow sensor of the DHW circuit of the Neva Lux boilers;
• replacement of the water overheating sensor for double-circuit boilers Neva Lux;
• checking and replacing the temperature sensor of the DHW circuit to maintain the set temperature and correct operation of the Neva Lux household boiler for preparing hot water;
• repair of the ignition system in the Neva Lux boiler, replacement of the electrode, transformer and other spare parts;
• repair of the flame control system on the burner; replacement of the ionization plug for all models of Neva Lux boilers;
• diagnostics, setting the operation of the gas modulator valve, setting the factory settings for the gas supply to the burner block of the Neva Lux boiler;
• flushing, replacement, repair of the heat exchanger of the Neva Lux mounted boiler on the recommendation of a service engineer;
• repair (replacement) of the circulation pump of the Neva Lux heating boiler;
• replacement (repair) of consumable parts of the Neva Lux boiler: safety relief valve, valve for automatic venting of air from the heating system,
• preventive maintenance, check and repair of the burner device for boilers Neva Lux

Repair of gas boilers ISHMA

Repair of gas floor boilers ISHMA is always carried out at a high professional level. It is not enough to know these Russian-made boilers, these gas boilers need to be understood and felt what they lack, what is the cause of the malfunction. Our customers of the repair service are constantly convinced of this, when dealing with the specialists of our company.

Today, we repair all models of the ISHMA gas boiler, taking into account the new heating equipment and old models of gas appliances. Urgent, emergency, current repairs for floor and wall models of Ishma boilers are carried out according to the following names indicated in the list below.

Ishma wall-mounted boilers of low power:

• Wall-mounted combined water-heating boiler ISHMA 12.5 BSK IS-143.00.00-1. Installation and commissioning, repair and annual maintenance, a maintenance agreement and the entire package of documents from a specialized organization for a gas trust in the cities of Podolsk, Serpukhov, Stupino, Kashira, Domodedovo, Vidnoe and Klimovsk.
• Combined gas wall boiler ISHMA 12.5 BS IS 142.00.00. Repair and maintenance, adjustment of gas, heating system and chimney in the area of \u200b\u200bthe city of Mytishchi, Khimki, Pushkino, Klin and Solnechnogorsk.

Floor standing boilers Ishma with a capacity of 25, 31.5, 40, 50 kW:

• ISHMA 25 NOVA SIT IS -150.00.00 RE, foreign automation. Maintenance and chemical flushing of the heat exchanger gas. boiler Ishma in the area of \u200b\u200bthe city of Shchelkovo, Elektrostal, Yubileiny.
• ISHMA 25 U IS 9901,00,00-U RE, automation made by the plant in Ulyanovsk. Diagnostics and repair of the Ishma heater, cleaning of the steel heat exchanger in the city of Mytishchi, the settlements of Boltino, Belyaninovo, Zhestovo.
• ISHMA 31.5 U IS 9901.00.00-U RE, automatic equipment produced by the Ulyanovsk plant. Installation and commissioning works for boilers Ishma in the area of \u200b\u200bthe cities of Pushkino, Ivanteevka, Fryazino.
• ISHMA 31.5 NOVA SIT IS -150.00.00 RE, imported automatic boiler control. Contract for annual maintenance of the Ishma gas boiler house in Khimki, Dolgoprudny, Lobnya.
• ISHMA 40 NOVA SIT IS -150.00.00 RE, imported automation unit. Maintenance and repair of the Ishma heating boiler in the area of \u200b\u200bthe cities of Klin, Zelenograd, Solnechnogorsk.
• ISHMA 40 U IS 9901,00,00-U RE, Ulyanovsk automation unit (Russian production). Elimination of a leak in the heat exchanger of the Ishma boiler in the city of Istra, repair or replacement of the Ishma boiler, the Arbat gas automatics in the Istra district, as well as in the cities of Dedovsk, Nakhabino, Krasnogorsk.
• ISHMA 50 NOVA SIT IS -150.00.00 RE, imported automation unit, 1 year warranty period. Repairmen of Ishma gas heating boiler in the area of \u200b\u200bthe cities of Lytkarino, Mozhaisk, Odintsovo, Volokolamsk, Sergiev Posad, Podolsk, Naro-Fominsk, Mytishchi. The service center operates on duty, servicing the contracted owners of Ishma floor boilers in the Moscow and Tula regions.
• ISHMA 50 U IS 9901,00,00-U RE, domestic gas automatics. Service of boilers Ishma in the cities of Balashikha, Kuravskoe, Zhukovsky, Ramenskoe and Voskresensk. The repair department of the service center works according to the production instructions and recommendations of the Ishma heating equipment manufacturer.

Boilers with forced circulation of heat carrier, power 63, 80, 100 kW:

• ISHMA 63 UE IS -9902.00.00 UE RE, electrically dependent, UE
• ISHMA 80 UE IS 9902,00,00 UE, volatile, UE
• ISHMA 100 UE Is - 9902,00,00 UE, RE, UE series
• ISHMA 100 Elletrosit IS-225.00.00, automation made in Italy
• ISHMA 100 U2 IS-9902.00.00 U2, Russian automatics
• ISHMA 80 Elletrosit IS-225.00.00, foreign automation
• ISHMA80 U2 IS-9902.00.00 U2, Ulyanovsk automation unit
• ISHMA63 U2 IS-9902.00.00 U2, Ulyanovsk automatic equipment, assembled
• ISHMA 63 Elletrosit IS-225.00.00, automation of imported production

High-quality repair of boilers is guaranteed by the manufacturer of this equipment with its stable supply of spare parts and components for uninterrupted repair of ISHMA heating boilers. The simple design, taking into account the modern technical characteristics of ISHMA gas boilers, at the same time reliability and safety during operation, puts these Russian heating boilers on a par with the world leaders in heating technology. This is not a simple comparison is confirmed by minimizing the repairs of ISHMA gas boilers.

Every year, improving the quality indicators of ISHMA heating boilers, manufacturers have achieved superiority in the repair of their boilers in comparison with other factories, and the cost of spare parts for boilers and repair work differs at times, the earth and the sky are involuntarily remembered. Repair of non-volatile gas boilers ISHMA is an indicator of the perfection and professionalism of service engineers in solving urgent repairs in the winter. You will find practical advice and feedback on the repair of ISHMA gas boilers in the "Articles" section of our portal, where you will emphasize a lot of new and useful things.

Repair of gas boilers AOGV in the Moscow region

Repair work with floor-standing gas boilers AOGV, AKGV, AOGVK is mainly associated with minor problems of a domestic nature. When using low-quality water in the heating system, the AOGV heat exchanger flowed; AKGV does not start or does not produce hot water; the gas heating device is water-heating according to the description, but does not want to heat and cannot. The classic Russian question “What to do?” Arises.

Repair of Russian gas boilers of the AOGV type begins from the entrance to the furnace room. If the boiler room is clean, there is no dirt and dust, this is already 30% of the fact that the AOGV boiler will last a long time without serious breakdowns. All hot water boilers of this type are produced with an open combustion chamber, that is, the chimney with good draft works great as a vacuum cleaner, drawing in not only dust, but also small debris, which impairs the heat exchange of the heater.

It is difficult for the automation unit to put up with this and often domestic AOGV are faulty due to such an incorrect attitude of users of this heating technique in their home. The cheapness of the outdoor AOGV has always attracted the Russian consumer. The low cost of repairs and original spare parts for the gas unit, the real availability of each AOGV owner to a “painless” replacement of the boiler with a new similar water heating device - there is a great advantage for the owners of this heating equipment in a private house. But there is one "but".

If AOGV is an inexpensive household heating boiler, and the reviews about this device are excellent, the appearance of the AGV gas boiler, to put it mildly, is not the same as that of modern French gas equipment, this does not mean that annual maintenance, planned replacement of spare parts and parts, chemical washing of the steel heat exchanger and other preventive measures provided for by the norms, rules of warranty and operation of heating equipment from the manufacturer.

AOGV and its varieties are an excellent high-quality Russian-made gas boiler. The repair base of this water heating device is provided by the manufacturer much better than for similar imported heating boilers. With conscientious and timely service, AOGV can last for several decades. Our company has been servicing this kind of boilers for more than 20 years without replacing the heat exchanger, prolongation of the maintenance contract is always welcomed by our specialists. Replacing a domestic heater is the most extreme measure during maintenance!

The repair of the AOGV control unit is accompanied by replacement after 7-10 years due to mechanical wear of the gas automation parts. Frequent repairs of AOGV gas boilers are associated with the interruption of the gas supply to the main burner. These moments are found both in electrically dependent and in boilers that are not dependent on electric current (non-volatile). Here you need to take into account the repair of automatic equipment for traction, repair of automatic equipment for overheating and other nuances that experienced specialists in the repair of gas equipment AOGV will always find out.

Repair of the VS8620C automation unit in AOGV electrically dependent boilers is practically impossible. The manufacturer of automatics for gas equipment Honeywell provides for the safety and correct operation of the gas valve setting by means of pressure measurement fittings, and the ignition flame adjustment. Careful handling of the rotating parts of the unit, such as the thermostat, the automatic start button, ensures long-term comfortable operation of the VS8620C automation unit and the boiler as a whole.

The repair of the SIT 820 NOVA control unit initially takes into account the subtle points of tuning the piezo ignition and the design of the igniter. During planned repairs, the quality work of the thermocouple must not be overlooked and it is imperative to check the internal current - the basis of the device's performance. In many cases, the automatic safety shutdown of the gas supply to the main burner provides not only the circuit of the automation unit, but also the so-called floating errors, which are known to qualified technicians, and specialists of the "generalist" always offer replacement of any part.

If you decide to save money - make the right investment in a quality repair of the Russian gas boiler AOGV with our service engineers at the technical support center in the Moscow region. Find out more when contacting the company's emergency dispatch service to implement free diagnostics by phone. The on-duty engineer will discard all unnecessary things in the past and issue a qualified resume for your heater.

Repair of gas boilers Protherm (Proterm)

Gas boilers Proterm produced in Slovakia, have established themselves as high-quality heating equipment at relatively low prices, given the cost of similar heating boilers from well-known foreign companies.

Repair of gas wall and floor gas boilers Proterm is inexpensive, given the quality of the equipment itself and spare parts for the boilers. Parts for replacement are analogs of spare parts for other manufacturers, which emphasizes the authority of Proterm on the global heating equipment market and in the Russian Federation.

Our company carries out repair and maintenance of gas boilers Proterm for the following models of floor-standing gas boilers: Wolf KSO, Bear TLO, Bear PLO, Bear KLOM, Bear KLZ, Grizzly KLO. Boilers of this type differ in the design of use, the type of cast iron heat exchanger and, if possible, the use of natural circulation in the heating system.

Non-volatile gas boilers Proterm work smoothly, like Russian boilers that do not depend on electricity. The most common malfunctions in floor-standing gas boilers Proterm occur from the lack of basic maintenance for several years, here you can observe: overheating of the Proterm gas boiler at minimum operating power modes; microcracks in the sections of the cast iron heat exchanger; with high-quality operation of the floor gas boiler Proterm, heating radiators in a private house do not warm up; the atmospheric burner of the gas boiler Proterm does not start or after starting it goes out; faulty piezo ignition and many other breakdowns of gas equipment Proterm.

Repair of gas boilers Siberia

Repair of gas wall-mounted and floor-standing boilers of JSC "Rostovgazoapparat" does not happen often according to the reviews of our company's experts. In this regard, I would like to note the high level of supply with spare parts and components for hot water gas boilers Siberia, one of the best examples of gas equipment for home heating.

Repair of Siberia boilers is carried out on the territory of the Russian Federation, in almost all regions. The availability of parts always and everywhere is due to their low cost, simple production and professional supply. Siberia boilers are being repaired due to untimely maintenance or due to their service life, which can be calculated in decades. If many manufacturers made the same high-quality gas heating equipment as the Rostov plant, then many service and repair organizations for the maintenance of boilers in private houses would be idle without work.

So, let's turn to possible repair situations for Siberia gas boilers. These include the option of losing the boiler power during the heating season during severe frosts, when the drop in gas pressure in the mainline is determined by the huge analysis of gaseous fuel by local consumers. In this situation, this kind of "malfunction" is possible in almost all gas boilers.

Malfunctions and the corresponding repair of wall-mounted gas boilers Siberia is practically similar to the repair of all wall-mounted heating boilers of this type from various manufacturers. This is due to the safety control system and the design of the wall heater.

There may be errors in the operation of the boiler in terms of shutting off the gas supply by the modulator valve. Single-circuit and double-circuit heating boilers have similar malfunctions, but in boilers using a circuit for preparing hot water, breakdowns are added associated with the operability of the hot water supply of a double-circuit wall-mounted Siberia boiler.