Do-it-yourself electric earth drill. How to make a homemade earth drill (yamobur, earth drill)

I'll tell you my experience. Elmotor 2kW with a reducer. On the shaft of Bur TISE. Hard clay. Two long handles for the motor / gearbox to hold (like a mustache), each about 90 cm. 1 turn in 2.3333 sec.
In short, if a stone or a large root comes across, it is impossible to keep. There is a lot of power.

Well his nafik manual elbur)

Useful information. Thank you.

What kind of shank?

Again, what kind of shank? What is the thickness of the steel?

And with the same drill that you cannot do the expansion?

And, yes, there is no need to cut off the handles from the noun TISE drill. They are comfortable. I just welded the adapter from the top to the center of the handle ..
Good luck ..

The handle of the tise drill can be left uncut if the space allows it to rotate in such a radius (this is the case not with a hand-held motor-drill, but with a frame drill or whatever you can call it).

This is a very interesting thought for discussion.
Which drive to choose - stationary or lightweight mobile.
A stationary drilling rig is also difficult to pull, even with wheels or without.
I chose the mobile option.
Firstly, the elmotor with a gearbox must be lightweight. He must be mobilely removed / put on a drill (and any).
Secondly, high rpm on the main shaft will wind up the driller and he will work in constant fear. Low rpm will reduce the risk of the worker winding up (wrapped), but too low is not needed - keep it for a long time (the person still gets tired).
Thirdly, the design is simply simpler and, accordingly, cheaper!

And for money - so you can hire any drillers ..
... to make unnecessary crap. adnak's excitement. I also suffer from this ...

And further. Please hear me. A mobile rig (when held with your hands) is a dangerous thing! I saw in the video how the driller did not hold the 2kW Rebir with the TISE drill in his hands. The revs are too high! And he himself did not keep up with the rotation. It's not far from injury! Turnovers need to be measured!
In short, I am opposed to attaching long handles to Rebir 2kW and drilling with comfort. It is dangerous! .. With standard handles, you will release the drill yourself, and then this is it. The drive must be lightweight and with comfortable turns! something like that...

Something I did not understand you - are you still for a mobile (hold the handle with your hands) or for a stationary (installation on a frame) installation?
Personally, I am in favor of a stationary one, because I will drill alone, a maximum of two people + raise, you need to lower the device yourself with a mobile installation + center it, .. and in a stationary setting, lifting is done with a winch, you do not need to worry about centering, you do not need to keep yourself in fear, that right now, like a stone, he will hit the head with a handle or something else more important. And at the stationary, if it rests against a stone or something else, it will tear off the key (nail or the like), which is located between the adapter and the drill shaft.

To create a well or conduct other type of earthwork, it is possible to use not only large-scale drilling rigs managed by specialists. On a small scale and enough time, simpler equipment can be used.

One of these tools is the earthen drill, a device that comes in many variations and varieties. In gardening and suburban work, it is most in demand, it is also used in various industries.

1 Design and purpose of the drill

An excavation drill is a device that is used to create cylindrical holes in the ground (to be more precise, the upper layers are drilled). It consists of a rod (rod), a handle and a drive. At the bottom of the stem there is a guide tip and a helical blade, mainly made in the form, or cutters.

All drills can be roughly divided into two categories: devices that require the use of manual force and automatic drills equipped with motors.

2 Types of drills

The classification of portable drilling devices, depending on the type of drive, is carried out into three groups: electric drill, hydraulic earth drill, and gasoline devices.

Gas drills are the most extensive category of equipment. A gasoline ground drill (aka a motor-drill) is the best option for domestic use, if the capabilities of a conventional hand drill are not enough. It easily penetrates soil layers up to 2-3 meters deep, in fact, the depth of the well is limited only by the size of the stem extension.

In addition to devices for economic use, there is a category of heavy gas drills for construction: these are fairly large mechanisms that are controlled by two operators. They are equipped with high-power engines that allow you to drill wells in problem soils: hard soil, sandy soil, or soil with a high content of mountain disseminations.

The main feature of such devices is that all engines are equipped with a gearbox, through which the engine torque is transmitted to the rock breaking element. Depending on the class of the device, two types of gearboxes can be installed on it: for heavy drills - worm gears, for light ones - coaxial gearboxes. Gasoline mixed with 92 oil is usually used as fuel.

The design of the motor-drill consists of the following elements:

• Drive: heavy - 3-4 stroke engines, light - two-stroke;
• Handle for holding;
• Control elements: power adjustment, gear change;
• Screws are usually used as a destructive element.

The cost of devices for household use starts from 10 thousand rubles. When buying, first of all, you should pay attention to such manufacturers as Hitachi, Husqvarna, Stihl - these are well-established companies, whose products have an optimal price-performance ratio.

There are also a large number of firms where possible. In general, renting is a great option if you only need the device for a few days. To date, rent, on average in the market, costs about 1000 rubles per day, plus you will need to pay a deposit of 5-10 thousand.

Electric drills are a less popular option than the previous one, but they are also common and well-known.

The only structural difference between such mechanisms and gas drills is the electric motor - all other elements are identical. The use of an electric drive adds both advantages and certain disadvantages to the device.

The indisputable advantages of electric drills include their noiselessness, since, unlike a gasoline engine, the electric drive is practically inaudible.

The disadvantages are as follows: electric motors have a relatively lower power than gasoline ones, that is, for the same money you can buy a more powerful gas drill than a device with an electric motor.

For domestic use, this is not particularly important, but in the case of professional use, this factor can become critical. It is also worth remembering about the mandatory connection of the device to the network, which somewhat narrows its portability, since any batteries have an unpleasant feature to sit down at the most inopportune moment.

The cost of high-quality electric drills starts from 15 thousand. The main manufacturers are Makita, Mora, Hitachi. Rent - from 1000 rubles per day.

Hydraulic drills are a category of serious industrial installations. The main advantage of such drills over gasoline and electric devices is the reverse function, which makes it possible to drill both clockwise and counterclockwise. Thanks to it, it is much easier to pass through problem soil layers.

In addition, hydraulic motors, in comparison with electric drives, are 2-3 times smaller in size and much lighter, which makes a hydraulic earth drill more convenient to operate.

But even with the same drive size, a hydraulic earth auger will always have more power. Hydraulic motors provide the most flexible regulation of shaft speed, which allows you to select the optimal drilling mode for different layers of soil.

The only significant drawback of drills with hydraulic motors is the "tenderness" of the drive. It is always necessary to keep it clean, since mechanical impurities inside the drive significantly reduce the service life of the device.

A hydraulic earth drill, in comparison with analogues, differs in several times more cost. So, the average price is 30-35 thousand. Renting hydraulic drills will cost you from 1.5 to 2 thousand per day. It is also possible to rent a hydrodrill with operators, in this case one hour of time is paid. Such rent will cost you about 1,000 rubles per hour.

2.1 How to make a drill with your own hands?

If you do not want to purchase something that you can make yourself, or you are not satisfied with the expensive equipment rental, then you can try to make a mechanical earth drill yourself.

To create a homemade drill, you need the following tools:

• Welding machine;
• Bulgarian (with circles for metal);
• Small repair tools - hammer, metal brush, pliers, sandpaper.

It is also necessary to acquire materials from which the structure will be made:

• For the stem - fittings 150 cm long, 15 mm in diameter. (adjust the height of the drill depending on your height);
• For the handle - fittings, or a metal pipe 40 centimeters long, with a diameter of 20 mm;
• For a cutter - a disc from a circular saw, or a sheet of metal 3-4 mm thick;
• For the "needle" (guiding element) - a metal drill with a diameter of 15 mm.

A homemade hand drill for earthworks is made as follows:

• We make cutters (blades) of the drill. If you take a disk from a circular for this, you can save a significant amount of time and effort.
• To make a cutter from such a disc, cut it in half, and grind off the blades with which the disc was originally equipped on each half. At first, you do not need to sharpen the edges of the cutters so as not to cut yourself during the welding process - the sharpness is given after all the connections are completed.
• In the case of using ordinary metal, make an approximate marking on the sheet and cut out two blanks with a grinder. Their size depends on the purpose for which the hand drill for earthworks will be used - for, or a well for planting trees.
• If there is no clear goal, then the best option "for all occasions" are cutters from 15 to 20 mm.
• We prepare fittings for the stem. It is not recommended to make a rod from two small pieces of reinforcement, welded together, since sooner or later, due to soil resistance, their connection will disintegrate.
• A metal drill is welded to the end of the stem, it acts as a homemade guide element (the optimal drill length is from 7 to 10 centimeters)
• We weld cutters to the junction of the reinforcement and the drill on the rod. This must be done so that there is an angle of 30 degrees between them.
• We take a grinder, put on an abrasive wheel for metal, and sharpen the edges of the cutters: remove the upper and lower layers of metal along the outer edges of the semicircles.
• We make a handle: a piece of reinforcement, or a steel pipe, is welded to the top of the stem perpendicularly.

You can also make a slightly improved design - a homemade hand drill for excavation with an extension stem. To do this, a bolt is welded to the drill handle, and a nut is welded to the upper part of the stem. A piece of metal pipe is used as an extension, on the edges of which a bolt and nut are welded, identical in size to those welded to the handle and stem.

2.2 Design and application of the drill (video)

As a fisherman, you learned what it is like to carry a Russian ice screw to the bite when it's -20 ° C outside. As the owner, you experienced the feelings of a man who dug 20 holes with a shovel while building a fence.

Domestic ice screws no longer attract you with their availability and unproductiveness. You come to a shop selling small-scale mechanization products in order to buy imported products.

The numbers on the price tag are significant, but the amount of work on your site does not correspond to them. Buying an expensive tool for seasonal work is an irrational decision. And you once bought a chainsaw, but it turned out to be not so necessary.

This chainsaw can be turned into a presentable motor drill. Thanks to your ingenuity, you will get two tools and save a lot of money.

Characteristics of motor-drills

If you doubt whether a homemade tool is worth the time and effort, then you do not know how much small earthwork can be completed in literally an hour.

You can drill holes for poles, lanterns, for planting trees, erect foundations, arrange a site in accordance with your aesthetic taste and needs, without resorting to renting special equipment and manual digging.

If an earthen drill can handle some hard types of soil, it will also overcome ice more than a meter thick. On ice fishing, you will fish, not drill holes.

The criteria that a good DIY motor-drill possesses:

• Power... For household needs, at least 3 horsepower is enough. Engine power of some modifications reaches 6 liters. with., but it all depends on the operating conditions.

  A compact and lightweight drill you can control yourself, a more powerful one will require the presence of another operator.

• Engine capacity plays the same role as power. The more cubic centimeters of the fuel mixture the engine can hold, the wider the possibilities of the motorcycle.

  The main guideline when choosing a volume is the nature of the soil. Alumina, sand, frozen soil require different engine performance.

• Functionality, drilling capacity. Which auger will pull the motor? What will be the diameter of the screw in millimeters? Is it easy to find the auger in the store, or are you having trouble with the delivery?

  Does the auger come with an extension, is it specific to the model? By answering these questions, the user will be able to determine which tool he needs.

If you are interested in making a quality motor-drill on your own, you need to add that the fruit of your efforts will not depend at all on talent. The process will require knowledge of turning and knowledge of the principles of operation of simple mechanisms.

There is nothing difficult in making a motor-drill with your own hands. If you are an expert in gearboxes, you will be able to bore the bushing of the desired diameter and build a quality mount.

Some abilities are indispensable here. Get the support of a locksmith you know if you don't have the practical skills to work with parts.

Chainsaw motor-drill

When faced with a similar question for the first time, you may be surprised that the chainsaw is used not only for sawing wood. This is just one area of \u200b\u200bapplication.

A chainsaw can make a smart gas cutter, a winch, a drill, a motor for a boat, a debarker, a device for breaking logs onto boards, etc.

The functionality is provided by the design features of the chainsaw:

• unpretentious and reliable engine;
• sealed supply of the fuel mixture, the leakage of which is possible only if the chainsaw is turned over;
• the main thing is a power take-off system that is clear to everyone. The output shaft of the chainsaw allows you to attach any attachment.

Therefore, it is advisable to take the chainsaw as a basis for a new device. There is no need to sacrifice it for the sake of a motor-drill: you will disconnect the drill bit, put down the saw and will cut the logs.

The chainsaw engine is designed for long-term and intensive operation, so you don't have to worry about breakdown or poor-quality task performance.

In theory, you can make a similar motorcycle tool from a trimmer, lawn mower or grinder.

In practice, this is quite difficult due to the unusual gearbox design. Problems can arise due to insufficient PTO or improper rotation of the auger.

Working process

So, how to make a do-it-yourself moto drill from a chainsaw?

Prepare your chainsaw. In most cases, the Soviet Stihl saw is used.

The auger should rotate at low speed. We need to find a way to reduce the speed so that the output turns out as much as is necessary for safe work with a motor drill. Therefore, in order to make a motor-drill with your own hands, you need a gearbox.

V-belt and worm gearboxes perform the same role, despite design differences. But in this case, worm gear is preferable.

Note: The efficiency of a worm gear is lower than that of a V-belt. The worm gear heats up faster, but it can be mounted directly on the shaft of the base machine. No couplings or mechanical transmissions are needed.

The large gear of the V-belt transmission must drive the auger!

You have dealt with the gearbox. But where can I get it? Better to buy. On the Internet you can find stories about daredevils who, armed with a grinder, screwdriver and hammer, disassemble old tools and remove gearboxes from them. Also an option, but unreliable and barbaric.

The gearbox and the motor of the chainsaw must be fastened. You may need the help of a locksmith at this stage. Usually, a bushing of the required diameter is bored - it serves as a connecting link.

Additional hardware required. You can't buy it anywhere. This is a handicraft, the mount is selected individually for each device.

Left pick up a drill and knives for it. The auger and auger must match in the direction of rotation if the device is assembled. The most popular are Tonnar, Mora, Hitachi. The cost usually does not exceed 5000 rubles.

It is advisable to pick up knives "native" and not made in China, especially if you will use a motor-drill for drilling holes in winter fishing.

Chinese ones burst, fall off, crack and cannot always be restored by welding.

With a homemade motorcycle tool, you can drill a hole with a maximum diameter of 150 mm. Practice will tell you what, how and how to drill. Everyone chooses the best option for themselves.

Drill motor drill

It is much easier to build a similar device from a drill. High power is a must for a drill. Better to use a puncher.

The process will be less laborious, because there is no need to look for a gearbox - it is part of the perforator design. In addition, drills are among those devices that are aggregated with a drill without additional parts.

A safety clutch is installed between the output shaft and the shaft of the driven drill. It prevents additional load from being applied to the gearbox and auger so it will not get stuck.

Rotary hammers are always equipped with a reverse, unlike drills.

Making a motor drill with your own hands from a drill is a little more difficult:

1. Need to pick up a drill with a capacity of at least 2 kWwith a receiver. The brand and year of manufacture do not matter.
2. Buy a worm gear (can be used) with a gear ratio of 1:25... Coaxial can be purchased, but using it can be inconvenient.
3. Auger - either buy or weld yourself.
4. Fasten all the elements into a technologically complete structure. You may need to seek help at this stage, although with the tools, materials and logic available, you can design the fasteners yourself.

   The main thing is that it is durable, neat and does not interfere with the normal operation of the motor-drill.

The advantage of a chainsaw over a drill is its autonomy. The drill works from the mains, which narrows the scope of its application, and the "chainsaw" motor-drill can be used in winter fishing conditions.

The advantage of the drill: there is no fuel mixture in it, no oil. The drill can work in sub-zero temperatures, and the chainsaw freezes. You have to spend time warming it up.

Driller's Memo

Creative inventors can mount a motorcycle, electric drill on a cart. If the tool is often used on the farm, this will be convenient.

Before making your own motorcycle tool, calculate the possible costs (gear, drill, auger, knives).

Compare with the cost of a new auger. If the difference in favor of a homemade product is significant, it makes sense to make an effort to make it.

The gearbox is not for nothing considered the most important element of the motor-drill. The number of revolutions at the outlet should correspond to the requirements for comfort of work.

A high RPM will keep the driller energized and the auger will continue to rotate even after the device is turned off. Is it dangerous.

On the other hand, low revs lead to a lengthening of the time interval that is required to complete a particular task. Hands and back will get tired.

Correctly selected gearbox is a guarantee of your "friendship" with a motor-drill.

Do you know how to choose a double row according to three criteria?

From you can find out interesting technical characteristics of the KB-403 tower crane.

At the following address, an article has been prepared for you that allows you to decide on the choice of a manual cultivator for a summer residence.

Do not lean on the tool while drilling. It can be difficult to cope with it, especially when the auger hits a stone. Be prepared for this and keep your distance.

Failure to comply with safety precautions threatens the same consequences, regardless of whether you work with a factory or homemade tool.

Before work, knead your hands - you will be more resistant to the whims of a motor-drill.

If old chainsaws, hand drills, drills, or a grinder are lying around in your attic, do not rush to get rid of them.

These tools will help you craft an expensive new device that will open up great opportunities for you.

The information obtained by watching the video can be applied in practice - when creating a motor-drill with your own hands:

An electric drill for earthworks is successfully used in cases where it is necessary, for example, to drill a hole for piles, make a trench or a recess for mounting fence posts, drill a hole for planting a tree or shrub, etc.

Brief description of the device and equipment advantages

By design, an electric earthmoving drill is an electric motor that has two handles and a clamping mechanism used for clamping. This tool is most often made in the form of an auger. It should be noted that the nozzles are removable and can be of different diameters, which allows you to adjust the size of the hole that will be drilled. It is also worth noting that there is a conditional division of drills into types, depending on their purpose. There are garden, earth and pile tools.

An electric drill for earthmoving is a rarity among people who have suburban areas, despite the fact that it has some advantages. If we compare it with the manual type, then, of course, the plus is that the main rotational force occurs due to the electric motor, and not human forces.

If we compare the device with a gasoline unit, then the advantages include quiet operation, environmental friendliness and readiness to work (you do not have to start it like a gasoline unit).

Equipment application

As mentioned earlier, one of the biggest advantages in terms of using a drill is that it can handle pile recesses with ease. Of course, you can do this with a manual type of unit, but an electric drill for earthworks will cope with this task much faster. In addition, the presence of small stones or roots inside the soil will make it very difficult to dig a depression, if it is done manually, this is not a hindrance for an electric motor.

Another ease of use of the equipment is that it is more compact than a conventional drill, and therefore its operation in places with limited space is most acceptable. Small dimensions and high functionality of the unit are its main positive qualities. It is also worth adding that in comparison with gasoline models, the weight of an electric drill is less, which makes it easier to work with it.

Models and flaw

Large models of motorized earthen drills are also used for digging wells, for example. Types with a smaller diameter nozzle are used for home use (planting plants, installing poles, etc.). However, it should be noted that the line of models also includes multifunctional types with removable nozzles. This makes it possible to use them depending on the needs, as well as on the quality and type of soil with which you have to work.

Naturally, the main disadvantage of the drill is that its operation in places where there is no electricity is impossible. Yes, when buying a device, there is usually a battery in the kit, but charging it lasts for a short period of time.

The principle of operation of the unit

An electric drill is an electric motor and a shaft of the type. When using such equipment, the hole in the ground will have smooth edges and a clear auger diameter. The direct drilling process is carried out due to the fact that the auger has a very sharp tip, as well as pointed helical blades. When the equipment is started, the electric motor starts to rotate, transmitting its force to the shaft to which the auger is attached. This is how drilling takes place.

Favorable cost of the device

The price of an electric drill for earthworks is also one of its advantages. The approximate cost of the device is 1,000 rubles. It is important to note here that for this amount the device itself and the basic nozzle that comes with the kit are purchased. And then you can purchase separately screws of different diameters, if necessary. Thus, the functionality of the equipment can be greatly increased at a minimal cost. The right choice will also help save money.

If you plan to operate the device in the garden, that is, for garden needs, then a power of 1.5 kW will be enough. If you plan to drill holes for construction needs (pile foundation), then you will need a device with a power of 2 kW or more. If there is such a need, then electric units can be used for ice drilling.

Reviews about the electric drill for earthworks are mostly positive. Of the main qualities that buyers highlight, it is worth highlighting ease of use, low weight, quality of the device and its relatively low cost.

There are also negative reviews. However, most often they are left by people who have not figured out the rules of its operation and have purchased, say, a less powerful model than was required to work with a certain type of soil. Naturally, the result was bad.

From this it should be concluded that it is imperative to investigate the soil with which you will have to work, to decide for which type of work the tool is purchased, and only after that you should buy it. It is also recommended to purchase products from only trusted companies. It is better to pay a little more, but buy a higher quality item than pay less and buy the equipment again in a year.

Moto drills from "Hitachi"

Electric drills for earthworks "Hitachi" are quite high quality and reliable products. The manufacturer of this equipment is Japan. However, it should be noted that the range of goods is not too large. Of the electrical models, only garden types are available. This means that the manufacturer does not produce electric models with high power. Only gasoline models from this brand have high power ratings. Today, three main qualities can be distinguished, thanks to which Hitachi products have become quite popular.

1. The assembly quality of the units is very high.
2. The efficiency of these devices is also high.
3. The service life of the devices is quite long.

Product selection and operation

When buying an earthen motor-drill, it is best to always go to a specialized store, where they can help with the choice. However, there are several guidelines that should always be followed. Three parameters should always be paid special attention to - power, auger head size and engine displacement (if it is a gasoline model).

Quite often, when working with this tool, it happens that the drill buries itself in the ground. For this reason, almost all new models are equipped with a safety system that turns off the engine if this occurs. This system protects equipment from damage. To avoid such a shutdown, it is necessary to periodically stop work and clean the auger from dirt.

It is also designed to protect the unit from accidental start-up or to protect a person if they lose control of the product.

In the garden, you have to use various equipment. To plant trees or build a fence, the owner will need an electric excavation drill. This device is simple in design and high in performance. It is only necessary to choose the right device, and the work will take less physical strength and time.

general information

Before going to the store for such a device, you should find out what an electric drill for earthworks is and how it generally works. Most models have a special frame as the main structural element. It has two handles, and an electric motor, complemented by a gearbox. The latter is necessary to increase the torque when using the device.

There are many criteria for choosing an electric drill

During work, the unit must be held by two people at the same time. When the gearbox shaft rotates, the torque is transmitted to the screw auger. Thanks to him, it becomes possible to perform a variety of earthworks. How much you have to spend on the purchase of equipment depends largely on its characteristics. The most important are:

• dimensions;
• power;
• operating conditions.

The range of such devices on the Russian market is small, which is explained by the limited scope of their use. But in fact, an electric drill is a fairly versatile device. The consumer should make the choice in favor of a particular type, starting from the type of soil prevailing on the site. In addition to this, you can purchase a variety of attachments that manufacturers offer for different surfaces.

Learn more about an earth storm in this video:

Advantages and disadvantages

Although an electric earth drill is available in stores, it is rarely used in the field. Many people refuse to buy a device because they simply do not know about its main advantages:

1. Saving physical strength. These devices are powered by electricity, so the work associated with drilling holes in the ground becomes an easy task.
2. Environmental friendliness. Unlike gasoline devices, their electric counterparts do not emit exhaust gases during operation, so there is no harm to plants and the environment.
3. Silence. The electric drill does not create noise during work. Thus, its use completely eliminates discomfort for neighbors.
4. Minimum weight. Modern models are lightweight, which also gives them an advantage over gasoline devices.

The main and only drawback of these devices is that the drill is tied to a 220 V electrical outlet. If the site is not electrified, then there is no way to use such equipment. Although many models are equipped with rechargeable batteries, the battery power is not sufficient for continuous operation of the device.

Application rules

Usually, an electric earth drill is used to make holes for planting fruit trees or shrubs. But even during construction work, this device can also come in handy. It is great for creating holes where piles or other support elements will be installed later.

Making holes in the ground manually is a laborious task, and it is noticeably complicated by the stones and tree roots encountered. However, the use of an electric drill can solve the problem quickly and easily. In a situation where it is necessary to drill holes in a hard-to-reach place where there is no way to place large equipment, such a device will greatly facilitate the process.

A variety of electric drills are available on the market today. They differ in size among themselves. They can even be used for jobs such as well drilling or well construction. If you need a device for performing a wide range of tasks in the garden, then it can be easily purchased at any specialized store.

The nuances of choice

In order for the equipment to provide high efficiency in use, it is necessary to select it correctly, focusing on the tasks to be solved. The main points that deserve attention when choosing an electric drill are the power of the device and the equipment of the device.

It must be understood that low power limits the scope of use. But the purchase of high-power equipment is also an irrational decision, especially if it is planned to use it only occasionally in the garden. The best choice would be to purchase a device with a power of 1.5 kW.

If an electric drill is required to install a pile foundation or perform another laborious task, then models from 2 kW and above should be considered.

A good completeness of the device ensures easy performance of a variety of works. Such a device can be considered universal, but this leads to an increase in its cost. In specialized stores, the minimum price for such equipment is 15,000 rubles. To get a high-quality and reliable device at your disposal, you need to seriously spend money.

Main manufacturers

Many companies make drilling equipment for use in garden plots. In countries such as Japan, Sweden and Italy, there are many firms producing electric drills ... Among Russian consumers, the devices of the following companies are most in demand:

1. ECHO. This Japanese firm produces a variety of products. The models are highly reliable and delight with their performance characteristics. Their feature is a rather simple design. This eliminates frequent breakdowns and facilitates maintenance. The average price tag for devices from this manufacturer is 28,000 rubles.
2. EFCO. The Italian manufacturer offers a variety of devices for drilling operations. A feature of the devices is their increased strength, they can easily withstand serious loads. The attachments are great for frequent use. The brand's products are offered at an average price of 29,000 rubles.
3. STIHL. The technique of this company is well known in the Russian market. The domestic manufacturer offers a variety of devices. Electric drills are also present in his product line. The models are practical and durable. They are also economical to use. The devices can be used to perform work of varying complexity and are equipped with a safe interlock system. The average price for them in comparison with foreign analogues is much lower and amounts to 15,000 rubles.

By choosing a device from one of the well-known manufacturers, you can get a reliable device that will last a long time. It is not worth buying equipment from hands. The best solution is to work with a dealer. You can buy really high-quality equipment from the official representative of the brand, besides, in this case, competent service is guaranteed.