"Sliding mechanisms for doors. Mechanisms for sliding interroom doors Sliding door mechanism

Load up to 80 kg, unstained rims from a polymer of a new generation, bearings in wheels, rotating lower leashes.

1. What roller mechanisms for sliding (sliding) doors?

In essence, two carriages with wheels assembled with the mounting plate for the door suspension. They slide inside the top guide, "Vivid" door canvas. At the extreme points of movement, they put limiters - so the canvas will definitely not pop up from the guide and does not rush to the floor.

Previously, the wooden doors were fucked into two guides: one below, one above, but because of this, the splash collector grown in the opening. Therefore, now they are bypass one top guide, and a tiny and inconspicuous floor leash is saved from the breakdown and cloth cloth.

2. Rolleries Palladium: Requirements for interior door

The set of our rollers is designed for a web up to 80 kg. Is there a lot or a little? Just catch up: a standard door from an oak array weighs a maximum of 40-50 kg, and the shield hollow is some 15-20 kg. It turns out that Palladium rollers are suitable for almost all doors that is on sale.

In the width of the canvas, there are also no serious limits. If the door is single, then the canvases are up to 900 mm; If the bivalve is up to 800 mm on the sash. Again: 99% of interior doors fit into these limits. Already Russian production - for sure.

The only thing is not desirable to install a 600 mm web, because the door lumen will be very narrow (470-480 mm). However, the openings under the canvas 600 mm are except that in the nanouses of the Soviet building is once. Two: in the bathroom, the sliding doors try not to put in principle. Not that they have tightness and sound insulation to put.

3.Complection

Our rollers for the sliding doors coupe are supplied in a dense cardboard packaging with a blister. This excludes scratches, damage to the goods during transportation or negligent storage.

Inside the package full combat kit for one sash:

Roller carriage - 2 pcs.

Mounting plate - 2 pcs.

Adjusting bolt with nut - 2 pcs.

Stroke limiters with a retainer - 2 pcs.

Outdoor leash with rubber cap - 1 pc.

Self-timber 32 mm for mounting the mounting plate - 8 pcs.

Self-tapping screw 20 mm for fastening the lower guide roller - 2 pcs.

Spanner - 1 pc.

Thus, for the door suspension, the upper guide remains (there is on sale with us).

4.Well benefits and know-how

Superisno-resistant wheels

Rimp Palladium rollers made of reinforced polyformaldehyde with filling. This is superproof, hard, but elastic material - can be said, a synthetic substitute for metal. It is resistant to abrasion, the formation of cracks is not afraid of water, and the fatigue resistance of it is 1.5 times higher than that of its main competitor - polyamide 66. Therefore, polyformaldehyde is ideal for repeating mechanical impacts, shock load and vibrations - everyday routine, which Expect rollers. In general, if the door is up to 80 kg and installed with straight hand, then the wheels will not wear.

Plus polyformaldehyde also in the fact that it is perfectly poured and processed. Look at the photo: The wheels are ground to perfection. The same perfect and move: soft and absolutely silent.

Ball bearing in every roller

And if more precisely - 80025 (625 Zz according to international classification). This is a radial single-row high carbon steel bearing. It provides a smooth and silent move of the wheel, and at the same time prevents its wear, reducing friction.

Bearing closed, and this is a plus: metal washers protect its cavity from clogging, moisture and lubrication leakage. It is not necessary to update the lubricant - it has already been applied at the factory in sufficient quantity.

Why are we so poisoning on the fact that in our wheels real ball bearings? The fact is that now there are many greedy producers, which for reducing the cost of production are completed with the wheels for sliding doors sleeve. It is like a bearing, but there are no balls inside. As not and sense: the door will ride the tight, jerks and lowered noise decibels. In general, it is better to buy rollers for sliding doors with ball bearings than to take damn that and change in six months.

Coarse carriage of zinc aluminum alloy (CAM)

Unlike the same steel, the cam perfectly pours and processed, therefore the surface of the carriage is smooth, geometrically correct, and all sizes and tolerances are accurate. Lyuft is just nowhere to take. Other advantages are rust resistance and excellent decorative adhesion. The usual structural steel and rests here.

On sale There are rollers for the door-coupe with carriages of stainless steel. They can exceed our in the carrying capacity, withsting up to 100-120 kg. But: a) the interior doors under the centner does not happen; b) the price will be more expensive; b) Stainless steel is perfectly processed - there is a risk of backlash and a knock on the carriage.

There are still plastic carriages with a needle bearing on the axis. Maximum their capabilities - carry a cardboard interior door weighing 15-25 kg.

Steel mounting plate with plastic latch (instead of a second nut)

The latch locks the bolt without giving a carriage to jump out from the mounting plate. Previously, for this, it is completely used near the second nut. Many manufacturers and now it is true, but we stopped on a more advanced version - latch.

Why she? First, so faster: shifted with your finger - and ready. No need to turn anything to a wrench. Secondly, the second nut limit the adjustment height simply because it is somewhat thicker than the latch lid.

Lower guide roller (instead of a simple leash)

So that the suspension door does not hesitate as a pendulum, in the corner of the opening from the side, where the door opens, the lower leash will be attached. He "checkbox", "knife", "heel".

How does everything happen? On the lower edge of the canvas make a groove for 1-2 mm wider leash. Now that the rollback door shifts, it enters the groove on the leash. Well, the one as the Atlanta supports the door, giving stability below.

In the most primitive version of the checkbox - this is a plastic rectangle on the site:

There is still a leash with a shock-absorbing cap. As a door stopper, only smaller:

Today, the rotating leash with a rubber cap is increasingly used. In fact, this is the third (lower) roller in the system. Simply put, if you want the sash to slide a little more quieter and smaller, we recommend buying rollers for sliding doors with a rotating leash. In our - just such.

5. Installing the mechanisms of sliding doors Palladium

Consider the easiest and most popular way of installation: the door is single, moving along the wall. The upper guide is attached to a wooden bar, no bottom.

What will take:

Set of roller mechanisms "Palladium" - 1 pc.;

Door canvas - 1 pc.;

Upper guide - 1 pc.;

Wooden bar (one length with guide; ideally - with a cross section of 60x40 mm) - 1 pc.;

Decorative eaves - 1 pc.;

Tools (drill, screwdriver, milling, measuring instrument, etc.).

Brief instructions on the installation of sliding mechanisms:

1. Calm the height of the canvas. Mark her line over the opening.

2. Measure the height of the guide with the carriage already collected in it. How many millimeters it turned out - so much and retreat from the first line. In this place, fueled the second horizontal line. Tip: If the door is standard, most likely, this line will take place somewhere 7 cm above the opening.

3. Entertain the bar of the bottom along the diverse line just. Break the bar so that one half of it closely closes the opening, and the second one walked along the wall, to which the door will move.

5. Clear the roller mechanism (carriage + bolt under the mounting plate) and boil into the guide.

6. Check how rollers move. If everything is fine, fasten the stroke limiters along the edges.

7. Go to the door. If the door handles and the lock still do not cut - do it now, while the canvas is not hawined.

8. Act: while the canvas is not hawined, make a groove in it for the bottom leash. Having retreated from the bottom end of the door (from the wall side, where it will open) 10-15 mm at the edges, drill the holes with a diameter of 6-7 mm and a depth of 20 mm. From this point, promise the groove by 1-2 mm wider than the lower leash.

The groove should reach almost the entire width of the canvas, not reaching the opposite end about the width of the limiters. It is necessary not to spoil the opposite bottom end with a ugly and unnecessary hole.

9. Similarly, 2 cm from the edges of the canvas, install the mounting plates. A semicircular cutout in the plates should look at the wall.

10.Nave the door under the guide. As a result, the suspension door should hold onto the roller mechanism as:

11. Crop the cloth from the wall and insert the lower leash in the groove. Now close the door and move the leash until the opening stops. Screw the leash to the floor.

12. If you need, adjust the interroom door vertically, shifting plastic latches on the rollers and twisting the bolts. Everything, you can now close the bar with a decorative cornice rail, and ready.

More detailed instructions for the installation of roller mechanisms "Palladium" can be found in the package to the kit.

6.Roligas Palladium for skipping doors: How much do you stand and where to buy?

Our sliding mechanisms are sold in the construction departments and network hypermarkets of Russia and the CIS countries.

Do not want to run shopping? Wearing that the necessary product will not be available? Then you easier - that is, in our online store. We have a 100% product in stock, delivery to any point takes from 1 day, and there is still an information support department, where you will be prompted and explained everything that is incomprehensible.

The price of one set of rollers for interior sliding doors is 915 rubles (wholesale cheaper!). Warranty - 2 years, service life is unlimited.

Tags: sliding doors

The times when the stores sold exclusively simple swing doors were sold in the fly. The modern consumer may pick up the canvas for its dwelling of various designs and mechanisms. Each of them has its own features, pluses and minuses.

Special attention deserves a popular mechanism of sliding doors, which is in great demand.

Advantages and disadvantages

First appearing on the market, the sliding doors produced a real extension. These options quickly won enviable popularity among apartment owners and private houses. The demand for similar designs was due to their original design and good performance characteristics.

At the moment, the sliding canvases are difficult to surprise anyone, as they tightly entered the life of modern users.

These beautiful and functional models have a number of advantages providing them with great popularity.

First of all, it should be noted the noticeable savings of the living space when using sliding doors, as they are not at all similar to classic swing structures, and the sash in them during opening or closing do not occupy additional space. This characteristic is especially useful in small-sized dwellings, which are quite a lot today.
Many people mistakenly believe that the installation of such systems is complex and time consuming. In fact, everything is much easier, and with many stages of work it is possible to cope without the involvement of specialists. Before installing sliding structures, it is not even required to produce preparatory work.

Of course, it is impossible not to mention the spectacular and rich appearance of sliding structures. With the help of such elements, you can revive the living space and give it a special style.
Many consumers are pleased with the fact that, in the process of opening and closing, such systems do not make unnecessary noise or squeaks.
Modern manufacturers produce sliding structures of various sizes, so you can choose the appropriate option for any conditions.
As a rule, in such a system you can install more than one door flap. It all depends only on the dimensions of the immediate opening and the type of cloth.

Based on the above list, it can be concluded that sliding doors are an excellent solution for a variety of areas and layouts, as there are many positive qualities.

However, like any other designs, they have some drawbacks.

Many psychologists believe that the main minus of the sliding doors is their relative novelty. Most consumers are accustomed to traditional swollen options, and they are not so easy to rebuilt on more modern web.
Because of this, there is another problem associated with the installation of such structures. It is not too complicated, but often users face ignorance of all the nuances relating to such work.
Despite the huge range of sliding doors, nevertheless, most of them have a high cost, which grieves many consumers.

It is also worth noting that the sliding canvases do not provide sufficient noise and thermal insulation. In this issue, these designs are strongly inferior to classic instances.
Many users face the problem of the accumulation of dust and dirt in a niche, which is necessary to install doors. Moreover, these sites are rather hard to reach, and clean them is not easy.
There is also the possibility that one day the mechanism in such systems will fail and swap. First of all, it can happen if the rollers in the design will be ash. To avoid such problems, specialists are recommended to acquire only high-quality and not the cheapest options.

These are significant disadvantages of sliding canvases or not, each person decides himself. Fortunately, modern manufacturers produce many beautiful and durable canvases of different variations, so even the most demanding owner will be able to choose the optimal option.

Designs

In all designs of sliding doors, the following necessary components must be present.

Guides (or rails).
Stoping mechanisms.
Motion limiters.
Roller systems (simply speaking, rollers).

Rails

These parts are one of the most important in the design of sliding doors. Without them, it will be impossible to open and closing the canvas and moving them to the side. Rails for sliding structures are made of steel, aluminum or metal base.

Rails in the sliding design are single and double. They can be installed both in the upper and lower area of \u200b\u200bopening. The upper parts are attached to the ceiling, and the lower - to the flooring.

Stoppers and limiters

These constituents do not have much influence on the state and operation of sliding systems, but perform an important function, which is to prevent the walls of the walls about the wall. Also these elements help to avoid arbitrary closing of the canvas.

Roller systems

In sliding structures are represented by the upper and lower rollers. The upper roller carriages can also consist right from several wheels. In different versions, they can be installed from 2 to 8 pieces. It all depends on the weight of the canvas. As a rule, rollers in the sliding design are symmetrically, but an asymmetrical location is also found.

Types of exfoliation systems

There are several different types of door cave tubes. It is worth familiar with them.

Telescopic

This mechanism is installed on a sliding structure in which there are two or three door canvases moving in one direction. In this case, the sash, combined with the help of a synchronizer, are located on two rails located in parallel to each other. This option is not the easiest, if we consider it from the point of view of installation.

It should be borne in mind that the telescopic type of spleputs is extremely rarely used for canvases made of glass.

This mechanism can also be called synchronous, as it is characterized by a non-standard structural structure, in which both sash are disclosed synchronously. Often, in such a variation, there are hooks or special synchronizers, with which the first sash when driving pulls the following.

As a rule, structures with telescopic systems are installed in fairly wide and spacious doorways. If you competently install a system with multiple sash, the interior will become more original and stylish.

Barn

Ambar mechanisms can be attributed to the suspended, as they have the main load on the upper rails. During the opening or closing of the door with such mechanisms, there are no floors. These designs are characterized by an attractive appearance, so many buyers choose them.

Complinary

Door flaps in such mechanisms are installed in two or three rows and form a single line when closing, closing the guide rails. Complian canvases work on the principle of the coupe and move in their highlighted rail. Such structures also belong to attachments, and they are not recommended to install too heavy sash.

Hidden

Today, many consumers choose doors having an invisible mechanism. As a rule, he hides behind the ramp. Otherwise, such structures are called "coupe" or "tram". They are installed without an additional threshold, and their supports are attached to the upper portion of the canvas.

Experts argue that the installation of such systems is better to produce at the stage of construction or repair work in the dwelling. This is explained by the fact that the canvas with the mechanisms are mounted in the inside of the walls. If their thicknesses are not enough, then a kind of penalty is manufactured.

After such works, the walls repeat the thickness of the Penal. It is worth noting here that the hidden mechanism cannot be used in any case if you install glass canvas.

Swivel-sliding

The canvases equipped with such a mechanism are called the roto doors. Such sash can be attributed to hybrid structures with confidence, as they combine the characteristics of traditional swing products and the functionality of sliding options.

Such models are only two components: guide and roller systems. The rail with the grooves is attached to the top of the doorway, and the roller mechanism with swivel joints moves the wheels in the slots of the rails.

In the lower part of these webs, a special lever element is installed, which is combined with the upper half of the wheel base using the axis.

Such bases are not designed to install two or three canvases. As a rule, in one opening there is one roto-door. Roto-models with a swivel-sliding mechanism can be called universal, as they function perfectly both in spacious and compact doorways.

It should be noted that such mechanisms will work regularly only if the system has lobes from lightweight materials.

Shuty

Various locking mechanisms may be present in interior sliding doors.

Simple mechanical lock. In such options, a special hook is applied instead of the traditional riglel. It is issued from the lock case and falls into the hole located in the second half. This part can be located directly on the door frame or on the second sash.

Electromagnetic lock. The work of this option is based on a fairly powerful electromagnet. When you click on a special button in the lock, the voltage is turned off, and the magnetic field ceases to be active, and the rigle is cleaned. Such devices enjoy enviable and have a large number of positive parties, but their disadvantage is that they are much more expensive than simple mechanical devices and their work is impossible without electricity.
Electromechanical lock.Such options differ from the above-mentioned principle of action. However, as for electromagnetic locks, electricity is necessary for the operation of these devices. The electromechanical lock is controlled by the remote control.

Materials

Modern sliding canvases are made from different materials.

The most high-quality and environmentally friendly instances are recognized from natural wood. It can be products made of oak massif, walnut, alder, maple, birch, pine or cedar. These canvas stand quite expensive, but serve very long and do not harm human health, since they do not emit hazardous substances, even under the influence of high temperatures.

However, it is necessary to take into account the fact that you need to regularly take care of wooden copies, otherwise they can dry out, crack and lose fresh appearance.

Cheap and distributed are canvas From LDSP or MDF. As a rule, similar canvas have a simple and template design. They are distinguished by a long service life and wear resistance. But it is impossible to forget that LDSP is a toxic material, because there are formaldehyde resins in its composition. If you do not want to harm your health, it is better to get the doors from the E-1 class LDSP or vending options.

Elegant and beautiful in the interior looks sliding flaps from glass. It is recommended to buy models from the Kalented web, as they are stronger and wear-resistant. Not all sliding mechanisms are suitable for doors made of matted or transparent glass. For example, the hidden systems cannot be installed in such products.

The lighters are the canvas made from drywall. This material is easily processed, and it can be separated by wooden panels, plaster, paint, tiles and even puncture with wallpaper. Hypzard itself is not the most durable and wear-resistant material, it is very easy to damage.

How to choose good?

Before modern consumers, there is a chic selection of sliding interroom doors having different designs and mechanisms.

To choose a good option that lasts as long as possible and will not deliver any problems during its operation, it is worth take the following.

At first it is necessary to determine the type of sliding mechanism to use which you will be most comfortable. Most often, consumers choose a telescopic version, as it is suitable for a large opening. Also very attractive in the interior, all types of attractive designs look, but they should not overload too heavy doors.
Hidden options look more aesthetically, in the installation of which they often use a special penalty that increases the width of the walls. However, it is worth considering that such a design is not suitable for contributing mirror doors.
For doors made of lightweight materials, not only telescopic, hidden or synchronous mechanisms, but also swivel-sliding systems can be used. In the latter there may be only one door flap.

Also, choosing sliding doors, you need to pay attention to the materials from which they are made. The most disadvantaged are models from drywall, and unsurpassed quality can boast a canvas from the wood array. These designs can be installed in the interior of a variety of styles, be it eternal classic or retro.
Do not save on the purchase of such systems. Low-quality and interlayed cheap sliding doors will last long. Often, these designs are out of order due to the skew of the roller system.
Contact only the leading and well-known brands that make high-quality structures with sliding mechanisms. Such products will delight you not only by a long service life, but also a thoughtful appearance, on which, as a rule, experience experienced designers.
Selecting the sliding door, do not forget that it should fit into the interior design in which it will be. Also, the canvas should turn the furniture in the room in the color and style of execution.

The company has many years of experience in the market with sliding hidden doors. We provide only quality products, designers offer individual solving issues. The price of products competitive in relation to other manufacturers. Compliance with the deadlines is our credo, your door will be installed on the appointed time. Additionally, the goods can be bought in the online store, we are located in the city of Moscow.

Sliding hidden doors - features of use, installation

Installation of the canvas is carried out by professional workers who understand the nuances of work. Making a sliding mechanism, use durable and reliable material. The system is designed for long use. In addition to the doors, fittings for them are for sale. It will help to hide the moving slider and give the interior charm. Measure the door compartment in the wall and choose the product under it. Door sliding mechanism only in the size of the buyer. Hide the movement mechanism will be workers who set the canvas.

Sliding hidden doors are used as a drawing board. Such a feature will delight children. Sliding doors can hide the unwanted inputs, for example, in the storage room or basement. The wall looks one-component. The movement device is also hiding with special accessories. Retractable canvas are put when entering the loggia, a glass opening is made.

Assortment of sliding system

pencil Eclisse Syntesis Line;
invisible Wood Fittings Set;
pencil Eclisse Syntesis Line Double;
the canvas Open Space Unikit Desing helps to hide the passages in the house;
invisible Glass accessories set includes a retractable mechanism;
pencil Open Space Unico Desing;

Eclisse penalty is one of the common options.

There are two types of sliding devices - these are consisting of two canvases, that is. Double, and single beds - one canvas. Having a large opening in the wall, the system is placed in two canvas, in such a situation it will have several advantages. It is easier to open - a single-sided block is too heavy. In addition, having an elderly and children in the house, this design will create difficulties in movement. A single sliding door with a hidden mechanism is customary to put in small openings. To take a rational decision, come to our office in Moscow. Our employees will show a new disguised form of structures from famous designers. We will help you choose hidden sliding interroom doors. Retractable design is gaining momentum. Moscow is famous for the presence of such factories.

Does your dream come true about his own apartment? This is great, it is a pity that its size is small. If one person lives in the apartment, then this is normal. And what if the family consists of several people who should have their own personal space? Here, our wand-coronary will come to the rescue - sliding door mechanism. Do not know what it is? The answer is very simple.

Buy mechanisms for sliding doors in our online store

We offer mechanisms for sliding interroom doors at the best prices!

This is a set of sliding mechanisms that are necessary for the installation of interroom doors or partitions. Now such doors are becoming increasingly popular in small apartments, with their help you can visually expand the space.

Sliding mechanisms for interroom doors Consist of several parts:

The device of the upper direction, which is called the track (upper part of the mechanism).
Rollers for sliding doors, which are mounted on the door itself and create its free movement within the boundaries of the guide profile.
Lower profile with the lower soldier who prevents the door swing.

The door itself is equipped with rollers for sliding doors, which create its free movement within the boundaries of the guide profile. By the way, the absence of a lower guide profile makes it possible to move freedom.

Mechanisms for sliding interroom doorshave positive qualities. First, this is a very good designer solution. Secondly, there are no difficulties with the installation, and the absence of the lower guide on the floor does not limit the freedom of movement. The door opens absolutely silently. The sliding mechanism is suitable for interior doors of various types.

Our company offers its customers a great choice. With our systems, you will forever forget about the lack of space indoors. For this you need mechanisms for sliding doors buy and install. The sets of sliding mechanisms from various types of material are manufactured. Such designs are excellent, not only for apartments, but also in offices, in production or in a private house.

We offer buy mechanism for sliding doors consumers with any income. They are suitable for different settings. By purchasing our set of sliding mechanisms, and installing the door, you can invite guests, not experiencing about the small area of \u200b\u200bthe room. The door will not create obstacles and visually limit the space space.

Our online store is created to make your life much more comfortable.