Do-it-yourself gas forge forge: how to make a mini forging device from available tools. Do-it-yourself forge from a tin can Do-it-yourself forge from a can

Dear friends and visitors of the site "" from the presented material you will learn how to make a small and full-fledged forge out of a simple tin can. Yes, yes, exactly a forge, with the help of which it will be possible to heat steel to red and forge a knife, for example ... Today the blacksmithing theme is quite popular, both among young people and the middle generation. Working with metal has been respected since ancient times, the profession of "Blacksmith" was the most respected among the artisans of antiquity. Even when the city was attacked by enemies and destroyed all living things around, the Blacksmith was not in any way touched, but taken to themselves (by will or not). History was forged by blacksmiths.

To subjugate the rebellious metal, it must naturally be heated to red, and this can be done with the help of a forge from a can. An ordinary can of canned food is taken as a basis, the walls inside are made of chamotte clay 1-1.5 cm thick. A hole is made in the upper part for installing a gas burner nozzle. M-6 bolts and pipe cuttings are used as legs. The stand can be made of plywood or board.

So, let's look at what you need to create a forge from a tin can.

Materials

tin
fireclay
gas-burner
metal pipe 22 mm
bolts М-6
nuts
board 25-30 mm
gas cylinder
dichlorvos cylinder

Instruments

hacksaw for metal
drill
putty knife
ruler
hacksaw
wrench
pliers
brush

Step-by-step instructions for creating a forge

The first step is to familiarize yourself with the drawing and diagram shown in the photo.

A tin or paint can is taken, as well as 2 bolts for making legs, 3 pipe trimming, two of which will go to the legs, and one will be installed in the top of the can exactly in the middle with a slight slope. As a stand, you can use a regular board of 25-30 mm.
The legs are screwed in this way.
Cutting pipes are put on the bolts and screwed to a wooden plank.
Attention! The pipe cut at the top of the can is installed at a slight incline. A gas burner nozzle will be inserted into this tube.
Then it is necessary to create heat-resistant walls inside the tin can, for which you need to use fireclay clay.
The thickness of the walls should be 1-1.5 cm. The clay is diluted with water in a container and brought to a homogeneous mass, and in order to form a cavity inside the can, insert a cylinder from under dichlorvos into it and fix it with tape. The mixture is poured inside, it is also necessary to tap the walls so that everything spreads evenly.
The clay will harden for about 4-6 days, after which you need to make a hole in the back, this is necessary for long parts.
After that, a gas burner is inserted into the hole and the clay is hardened, everything is also tested.
Thus, you can heat the metal to red and forge any object.
As a result, the forge from a tin can was painted golden, it turned out quite aesthetically pleasing.
As you can see, there is nothing complicated in the manufacture of a forge, everything is extremely simple and understandable, the materials are affordable and budgetary. If desired, the child will also collect. Once installed in your garage or workshop, you can forge small parts or knives. Now let's watch the video and consolidate the material covered.

Thank you very much for your attention! Come back often, we have a lot of interesting information.

A compact and easy-to-manufacture forge for forging metal (knives and other products) is offered by “advocate Egorov”. You can make it from a simple tin can and plaster with your own hands.

For work, you only need a screwdriver or drill. The blowtorch used in this forge is one of the cheapest. The author of the video tutorial bought it for 750 rubles. Now you need to screw the plumbing sleeve into the hole. To use a thread, the hole in the can must be smaller than the diameter of the thread.

You can cut a ring out of the pipe and use it as a washer. The nut is best used with a standard plumbing nut.

Next, you need to make a tight connection between the installed sleeve and the neck of the blowtorch. The neck of the blowtorch lined up exactly 1/2 inch to the copper tube. The author had a connector for such a pipe and pressed it into the sleeve using a vice.

It remains to drill 2 more holes in the jar for two bolts - the legs and fix these legs on the support.

The final stage is the application of a thermo-insulating gypsum layer to the inner surface of the can. Gypsum hardens very quickly (1.5 minutes), so it is useful to prepare all the necessary parts and tools before preparing the gypsum solution. It is necessary to prepare a cylinder (an aerosol bottle is convenient), which will form the cavity of the furnace, a spoon, water and other details.

First you need to mix gypsum and sand in a 1: 1 ratio. After adding water, knead the solution until smooth, like thick sour cream. Put the resulting solution into a jar and insert a cylinder inside to form a furnace cavity. To make it easier to remove the cylinder later, you can wrap it with wax paper.

Until the cylinder is removed and the gypsum has frozen, it is necessary to make a channel for the flow of gas. Gypsum rises within 1.5 minutes. It remains to dry the forge and you can start working on it.

The performance of such a furnace is small and without a brick plug, its operation will be wasteful. With it, productivity, that is, the speed of warming up, increases significantly.

It is better to ignite the gas not in the firebox, but in the socket of the blowtorch. It will be safer this way. The forge is a source of increased danger! Do not leave the burning forge unattended. Forging on such a furnace takes place at a temperature of 700 degrees, the metal does not heat up quickly.

I have a passion for blacksmithing and have long wanted to bring a piece of it to my suburban garage. After watching several thematic videos, I realized what to do, but I did not find any step-by-step instructions on this topic, so I decided to write down for you how to make a forge forge with your own hands.

Do-it-yourself mini-furnace assembly time from start to finish is about an hour and a half.

Step 1: Collecting the things you need

You will need:

Can
Wooden block
Pipe connector - 1.5 * 5 cm
Two L-shaped brackets
Two wood screws to secure the brackets to the wood block
A pair of small metal screws with washers and nuts to secure the jar to the brackets
Sand
Gypsum
Large bag for mixing plaster and sand
Conventional propane burner with spiral gas nozzle
Protective glasses
Fire extinguisher - just in case

Step 2: preparing the jar

Drill two holes approximately 1.5 cm from each edge of the can.

On the opposite side from the holes, about 2-3 cm from the back of the can, drill a 1.5 cm hole for the pipe connector, at a slight downward angle.

Step 3: screw the brackets to the wooden block

Measure the distance between the holes in the bank and screw the brackets to the tree accordingly.

Step 4: attach the jar to the brackets

Use screws, washers and nuts to secure the jar to the brackets.

Step 5: Thread the pipe connector into the jar

Just screw it inside, everything should look like in the photo: link. Try to think over the position of the tube so that when the burner fire begins to flow through it, it does not rest against the walls of the vessel, but smoothly leaves the tube and twists in the jar - this will increase the efficiency of the melting installation.

Step 6: create the heat resistant filler

Mix equal proportions of gypsum and sand, add enough water to achieve the consistency of wet clay. We used a 350 ml plastic mug and in our experience, for a large tin, we recommend mixing 3 cups of sand and plaster of paris and adding 1 - 1.5 cups of water to the mixture.

You need to work very quickly, as the mixture begins to set and harden instantly.

Fill the jar tightly about 3/4 of its volume, and then poke a hole in the middle with a radius of about 4 cm (for example, with a spoon), leaving walls about 2 cm thick.Choose a wider cavity at the back (bottom) of the can to create a better zone heat retention.

Use the back of a spoon or other thin object to remove the mixture of sand and plaster from the protruding pipe connector. Clean all surfaces with a damp cloth and let the mixture sit for about 30 minutes.

Later I figured out that you could stuff a pipe connector with paper, and to create a hole in a can, use a toilet paper tube and stuff a heat-resistant mixture around it, and then all the paper would just burn out on the first fire.