Do-it-yourself cake turntable is needed not only for real confectioners. This is a necessary item for those who cook for pleasure. Housewives who bake mastic-coated cakes cannot do without such a design. The main purpose of a turntable is to facilitate the process of decorating a cake. That is, you do not have to beat around and around the finished product, it will be enough just to decorate a rotating cake. Baking spins around its axis, and you only need to have time to decorate it.

How to make a turntable? To get started, prepare all the necessary materials. You will need two bearings, which are available from auto parts stores.

Please note that there are double, compressed bearings. The second option is preferable because you will have to tinker less.

The turntable also needs a wooden plate. You can stock up on the door from the kitchen set. In addition, you will need hard nails, self-tapping screws, plastic tubes, a metal circle, thin plastic, plywood.

Work process

Scheme Drawing

Making a turntable with your own hands is quite simple. First of all, you will need to draw a quality drawing. After that, we begin to work according to the following scheme. If you have two bearings, and not one pressed one, then we drive an element of a smaller diameter into a larger one using nails. It is necessary to cut out two circles with a diameter of 20 cm in a wooden plate. In one of the circles, a hole is cut in the middle into which the bearing is hammered. In this case, the two parts are twisted and fixed with screws. The bearing is placed in the center.

The do-it-yourself table is equipped with plastic tubes. The tube should connect the upper and lower parts. Consider this point when you make a drawing for the turntable. In this case, the tube must fit exactly into the bearing. The ideal length is 15 cm. Such a tube will not be too short or long, so you do not have to bend down to decorate the product.

The top is made of metal. In order for it to spin, pay special attention to its diameter. On average, the diameter of a metal circle should range from 30 to 40 cm. If you have the opportunity to weld the elements, it will only be wonderful. For those who are deprived of such an opportunity, cold welding was invented, which looks like plasticine. A cake turntable also requires circles cut out of plywood. The rotating part is mounted on the pipe, and the elements are fastened with self-tapping screws.

1 2 3 4
5 6 7

The table can be made of wood:

Cake turntable

Bearing Assembly of rotation
Table top base Rotating part assembled
Cake turntable (bottom view) Cake turntable (side view)

Baking cakes is not only interesting, but also responsible. The aesthetic appeal of the confectionery product and the ability to arouse the appetite of consumers depend on the quality of the decoration. Therefore, one cannot do without a special rotating round table designed for decorating sweets.

The stand consists of several parts. Using step-by-step instructions, you can make a turntable for a cake with your own hands.

What is a turntable for?

The swivel cake table is a great find for those who are fond of baking complex confectionery.

The device has the following advantages:

• greatly facilitates the final processing of the cake, rotating around its axis;
• the confectioner can decorate the product without moving, which greatly speeds up the cooking process;
• often on the surface of the table there is a special marking that allows you to create even and neat elements.

The rotating support will help professional confectioners and ordinary housewives to create culinary masterpieces.

Features of choice

In order not to make a mistake when choosing a good table, it should be evaluated according to several criteria.

Swing mechanism

The most important part of the model, without which the table simply will not spin, is the turning mechanism. It is a metal bearing, located under the tabletop, providing it with uniform rotation around its axis.

Diameter

The most common countertop diameter is from 26 to 30 centimeters. Such parameters have a cake of standard size up to four kilograms.

But for convenience, it is better to choose a larger diameter so that during operation you can lean on the countertop with your hand with a palette. This will help achieve a more accurate result.

Silicone feet

A necessary part designed to fix the structure in one place. This prevents the confectionery product from slipping on the surface of the countertop, thereby eliminating possible defects and damage to the cake during processing.

Such legs are quite inexpensive, in the region of several hundred rubles, but thanks to them, the product will turn out to be perfectly even and without damage.

markup

On the round surface of the tabletop there are special divisions that divide it into equal segments. This is the markup that helps to create completely even and uniform decorative details. In addition, the parts of the cake will be located at the right angles, which will certainly ensure a high-quality end result.

In the event that there is no marking, you can apply it yourself using a ruler and a compass.

How to DIY

The modern market offers many devices to facilitate baking products. However, by making a cake turntable with your own hands, you can save a lot of money. In addition, a home-made design can be created from your own materials, adapting it to specific requirements.

Necessary tools and materials

Various materials can be used to create a model. The most common options are wood, plywood, chipboard.

To work, you will need the following tools and materials:

• pressed bearings, 2 pcs.;
• lumber;
• thin plastic;
• metal circle;
• pipes made of plastic or metal;
• nails;
• self-tapping screws.

Further instructions will be devoted to how to make a do-it-yourself plywood rotating cake stand, as this is the most convenient and inexpensive option.

Manufacturing

Before starting work, you should make a drawing, indicating on it the details of which the model will consist, and their dimensions.

Creation instructions:

According to the drawing, two circles of the desired diameter are cut out of plywood - 20 centimeters.

A bearing is inserted into one of these circles. The hole for it is cut out in advance.

Two parts are twisted and fastened with self-tapping screws, and the bearing is inserted into the center.

The upper and lower parts of the table are connected using plastic tubes, if desired, metal tubes can be used.

They must fit very precisely into the bearing. The most optimal tube length is 15 centimeters. The upper part of the model is made of metal. Its size plays a very important role, so it is best to make a diameter of 30–40 centimeters.

Then the parts are interconnected using a welding machine. You can also use hot glue for bonding, which hardens when cooled. Next, the rotating circle is placed on the pipe and fastened with self-tapping screws.

The finished table is decorated in different ways. For example, the surface is decorated with crepe paper or thin plastic.

Video

Watch a video about making a wooden turntable with your own hands.

The swivel cake stand is an essential tool for pastry chefs: from beginners to real masters. If you want your cake to be accessible from all directions at the same time, but without having to “cut circles around it”, by all means consider having a rotating cake tray. Only he will help to make the cream decoration even. And the process of decorating itself turns into a bewitchingly beautiful action.

The swivel cake stand is an essential tool for pastry chefs: from beginners to real masters.

Such rotating coasters for decorating a cake look great at a large feast, on the windows of cafeterias or pastry shops. If you want to present a masterpiece made by yourself in the most attractive way, it is quite possible to use a rotating cake stand for this.

The product consists of:

• Round work surface;
• Bases in the form of a leg;
• rubber bands;
• rollers.

The design is designed so that the tray (stand) rotates freely around the axis. Thanks to this, access to the cake from all sides becomes convenient. Some variants are made with an inclination, so it is possible that the device bends at different angles. It is these designs that are most convenient when decorating desserts and when demonstrating sweet masterpieces. Such a stand allows you to create original decoration and form any decoration with maximum convenience. Moreover, the confectioner can absolutely not worry that his product will be damaged, move out or even fall.

The tilt stand allows you to create original decorations and shape any decorations with maximum convenience.

Types of rotating platforms for cake

In specialized markets, there are many coasters-trays of world famous brands.

Someone wants to have compact products for a dessert bar (Candy bar) when serving sweets. Some people like swivel models with an inclination, others will not be able to use only 2 tiers of the stand.

In specialized markets, there are many coasters-trays of world famous brands.

Varieties of design

There are such models, according to the form:

• Oval;
• A circle;
• Square;
• Rectangle.

As well as figured trays for an extravagant demonstration of confectionery creativity.

The turntable is often equipped with complementary accessories: it can be supplied “accompanied” by a spatula, lid, baking dish, pastry syringe, etc.

The rotary cake maker is often equipped with complementary accessories.

Materials from which the rotating cake stand is made

Cake racks are:

• steel;
• Glass;
• plastic;
• Ceramic;
• Wooden.

Rotating plastic cake stands are a rather fragile product. This is the most affordable option. Thanks to the last circumstance and the most common. They are presented in a wide range of models, are made with or without a slope. Plastic cake makers usually have a non-slip material, which helps them grip well on the table. This is very convenient.

Plastic cake makers usually have a non-slip material, which helps them grip well on the table.

The glass spinning cake tray looks elegant. It is made of tempered high-quality glass, often decorated with an original pattern. It looks neat, spectacular - you can take a photo and serve on a rotating plate. Has a non-porous surface, quickly and easily washes, does not absorb odors.

The glass spinning cake tray looks elegant.

Metal structures are heavy, but they are designed for a longer service life. They can withstand weighty cakes, do not deform over time.

Metal structures are heavy, but they are designed for a longer service life.

The wooden cake stand is constructed from natural material and looks aesthetically pleasing. Sweet products can be served directly on it. The cost is higher compared to a plastic rotating stand for decorating cakes.

The optimal diameter of wooden structures is at least 34 cm. Such a cake rack is roomy, it is convenient to decorate products from three kilograms (or tiered) on it and make confectionery decor on them. The wide surface makes it possible to place the leveling spatula in a convenient way.

A wooden tray has some advantages:

• He is durable;
• Does not absorb odors and moisture;
• It's easy to care for and easy to clean.

What is important - it "fits" into any interior.

The wooden cake stand is constructed from natural material and looks aesthetically pleasing.

The main criteria for choosing

When planning to purchase a kitchen attribute, pay attention to:

• Reliability;
• The quality of the material (it must be hypoallergenic and hygienic);
• Persistence.

Decide on the shape of the baked product, focus on the appropriate diameter. The wider the plate, the more convenient it is for the pastry chef to act. In specialized markets, you can find models with a width of 10 to 40 cm. Many consider the diameter 28 - 30 cm to be optimal.

Don't forget about the stability of the turntable. This is an important selection criterion.

When choosing a rotating cake platform, check if it has markings. This is a great help when decorating: decor elements can be distributed at the required angles, and the edges of the cake can be made as even as possible.

It is worth paying attention to the possibility of disassembling the structure: if the bearing breaks in the rotational mechanism, the non-collapsible stand will have to be thrown out. In such a situation, it does not stop functioning, but simply does not rotate normally. When you run a spatula along the side of the cake, it only twitches occasionally. This prevents the complete design of the product.

When choosing a rotating cake platform, check if it has markings.

Often, for most confectioners, the decisive condition for the purchase of such a cake maker is the presence of a transparent coating. It is ideal for serving purposes.

Popular with experienced craftsmen and additional mesh. It often comes as an accessory to a swivel stand. With this accessory it is convenient to cut cakes into beautiful pieces. It ensures accuracy in work: impeccable lines, symmetry, a layer of mastic or glaze after cutting is not smeared.

It is useful to buy a rotating platform on a leg for decorating cakes because today it is the most convenient inventory for decorating and subsequent presentations of sweet products.

The swivel tray is useful for banquet events and as a "showcase" for restaurants, cafes, confectioneries. You can purchase both an inexpensive plastic product and a six-tiered stand.

The swivel tray is useful for banquet events and as a "showcase" for restaurants, cafes, pastry shops.

How to make your own spinning cake stand

A turntable cake stand can be bought ready-made or assembled on your own if it is not planned to be purchased in the near future. A homemade device has many advantages:

1. You yourself are free to create a drawing of the product, think in detail what dimensions will be the most optimal.
2. You will be able to create a cake that will fully meet your desires and preferences.
3. A self-made design will cost less than purchased in a store.

You will be able to create a cake that will fully meet your desires and preferences.

Materials for manufacturing

A spinning platform can be made from the following improvised materials:

• Plywood;
• Tree;

Each option has its own advantages:

• Plywood and MDF are easy to process;
• It is safe to work with wood, the material is environmentally friendly, the texture is pleasant to the touch;
• Chipboard is inexpensive, has an attractive appearance, and work with it is pleasant.

Chipboard is inexpensive, has an attractive appearance, and work with it is pleasant.

Required tools for making

You will need the following:

• Bearings (you can buy them at any auto shop; they are pressed and double; the first option is preferable because they are easy to install);
• self-tapping screws;
• metal circle;
• Nails;
• plastic tubes;
• Lumber (in this case, plywood).

Necessary tools for making.

Manufacturing process

Think carefully about the sketch before you start work. Indicate on the drawing the design of the product, what are its exact dimensions, what are you going to manufacture from. With such a scheme at hand, you can assemble a rotating platform easily and without errors.

Sequence:

1. From plywood we cut out a round countertop according to the drawing.
2. Next, take the bearing (if not pressed, but double, hammer the smaller one into the larger one with nails).
3. In a wooden base, cut 2 circles (d 20 cm).
4. Insert the bearing into the circle prepared in advance.
5. Using self-tapping screws, twist both parts together, place the bearing in the center.
6. The turntable is equipped with plastic pipes. They should connect the top and bottom of the future tortoise. It is better to make a tube at least 15 cm long (to simplify the process of decorating baked products: in this case, you do not need to lean over the culinary masterpiece being made).
7. The top of the turntable is made of metal. Ideally, the diameter of the metal surface is 30-40 cm.
8. The elements are welded together. If you do not know how to use a welding machine, use cold welding. The rotating part is installed on the pipe, the elements are fastened with self-tapping screws.

Your design is ready.

In order for the rotating cake stand to acquire a decorative appearance, it should be pasted over with thin plastic. You can decorate the product with a self-adhesive film. Sticking it is not difficult, it is easy to clean.

If you approach the issue of making a rotating cake stand creatively, you can get different trays.

If you approach the issue of making a rotating cake stand creatively, you can get different trays. The main thing is to clearly align the drawing and select high-quality materials.

Video: Making a do-it-yourself swivel stand

2692 0 0

How to make a turntable: construction and design choices, plus simple assembly instructions

Rotating tables are furniture that is in demand in various fields, from the advertising business to metalworking. But this time you will learn how to make an easy-to-use turntable for everyday use. I bring to your attention a simple assembly instruction, plus recommendations for choosing the right design.

Select turntables

Illustrations	Types of furniture and their description
	Classic turntables. In this design, the turntable is mounted on a vertical support. Due to the presence of a bearing, the rotary part of the furniture rotates around the support by 360 degrees.
	Iconic Turntables. Such devices are used by professional photographers or videographers to capture various objects from different angles. The photo shows a small homemade table with a small diameter rotating surface.
	Glass rotating podiums. Such designs are used to display jewelry and other small items that need to be shown favorably from different angles.
	Wooden rotating podiums. These are massive dining tables of a round shape, in the center of which there is a swivel structure made in the form of a tray. The design is used during banquets and other events where it is customary to serve dishes beautifully. The presence of a rotary part is designed to facilitate access to dishes from anywhere on the table.
	Kinetic rotating podiums. The design is based on two combined transparent surfaces, on which certain ornaments are applied. When the position of transparent surfaces is changed, the ornaments are superimposed on each other in different ways, creating certain patterns, due to which a special visual effect is achieved, as shown in the photo.
	Automotive podiums. In fact, these are all the same countertops, fixed on a movable support. The surface of the podium is driven by an electric motor with a reduction gear. Given the weight of the exhibits, the design of the turntable is assembled from rolled metal and made as strong as possible.

Which of the following designs to choose for self-assembly? If the furniture is made for use in everyday life, we prefer the usual wooden structure, where a rotating tray is installed in the center of a round dining table.

Choose a tabletop project with a rotating center

The drawing shows a classic wooden table on a vertical support. A tray on a bearing is installed in the center of the tabletop. The dimensions indicated on the drawing are selected taking into account the comfortable accommodation of four people. In the assembly instructions, we will be guided by these dimensions.

The drawing shows a swivel assembly where the rotation of the tray is carried out thanks to a ball bearing. On the one hand, such a unit ensures smooth rotation of the tray, and on the other hand, guarantees a long service life of the entire structure. However, the design of the assembly can be simplified without compromising the smoothness of rotation by removing the ball bearing.

DIY: what to collect

Let's say you have an ordinary unremarkable round wooden table, but you want more comfortable dining furniture with a swivel center section for comfortable access to dishes. I offer simple instructions for assembling and installing the very rotary part, by turning which, this or that dish will be easy to get from anywhere at the table.

The assembly instructions in this article are intended for round tables with a diameter of 1-1.2 m. But what if there is no such furniture initially?

The instructions in the article are a guide to assembling a small countertop. Therefore, simply increase the proposed dimensions and, in addition to the turning part, assemble the main tabletop from the same boards.

Select materials

• Board 70×25 mm.
• Wood screws 30×5.
• Joiner's glue.
• Paintwork materials for finishing works.
• Rolling bearing (as an option, you can do it yourself, as described in the instructions).

Select instruments

For work we use the following:

• Electric jigsaw.
• Screwdriver with bits and drills.
• Big circle.
• Clamps.
• Pencil and ruler.
• Painting tool.

Assemble a turntable with your own hands

Illustrations	Make and install a turntable - step by step instructions
	Make a template. On old wallpaper or on unnecessary cardboard we draw a circle with a diameter of 550 mm. Cut out the circle according to the markup made earlier. If there is no compass, a rope will help to draw a circle. We tie a nail to one end of the rope, and a pencil to the other at the required distance. We put the nail in the center and draw a line with a pencil.
	Break the template into segments. We fold the paper circle in half, and then three more times to get 8 identical wedges.
	Make an insert template. We measure 3 cm from the extreme point of the circle along the fold line. We connect the marked points and get the workpiece as in the photo.
	Cut out liners according to the template. We cut off one of the eight extreme fragments from the template, as shown in the photo. We attach the template to the board and draw around the contour. Cut out the part according to the markup. To perform a curved cut, we use an electric jigsaw. As a result, we make 8 identical blanks.
	Sand the liners. We smooth out the bumps with sandpaper and clean the workpieces from dust.
	Make the base of the circle. We fold the previously prepared 8 parts and glue them end to end. In order to obtain an acceptable quality of gluing, we place the parts on a flat surface. From plywood 4 mm thick we cut out a circle with a diameter of 530 mm. We glue the plywood circle on top of the hoop glued from wooden fragments. After the glue has completely dried, turn the circle upside down and remove the influx of glue from under the planks.
	Fill in the base of the circle. We alternately apply the boards to the notch of the circle and cut them so that they stand close to the side along the edge. We glue the boards prepared in this way into the recess and place them under the load for the drying time.
	Lacquer. We cover the finished tray with varnish or other paintwork materials that match the design of the table.
	Set turntable. We attach the outer ring of the plain bearing to the main tabletop. We attach the mating part of the bearing to the bottom of the tray. We insert the tray into the bearing on the countertop, after applying grease.

Explanation to the instructions: how to make a plain bearing? In order for the turntable to rotate freely without swaying, you need a bearing that you can do yourself.

The diagram shows a simple plain bearing consisting of two rings - an outer and an inner ring or cylinder. Both structural elements are attached to the respective sides of the combined worktops.

The gap between the outer and inner ring in order to avoid play should be no more than 1-2 mm. One ring is attached to one countertop, the other to the other.

Perhaps the assembled assembly will not be as comfortable as a ball bearing when scrolling, but given the speed of rotation of the turntable, this is not so important.

Calculate the labor costs and cost of making a table with a rotating center with your own hands

What will be cheaper - buying a table with a swivel center or making such furniture yourself? Of course, it's cheaper to do everything yourself. Let's try to calculate how much it will cost to manufacture a turntable, described in the instructions.

You will need a board 70 × 25 mm, length 4 m, which costs an average of 130 rubles. Plus, you need self-tapping screws in the amount of 20 pieces, which will cost 20 rubles. In total, the materials will cost 150 rubles, and to this we add a little wood glue and varnish with a stain from a home workshop.

As for labor costs, they are quite comparable with the assembly of a conventional dining table. If you make only a turntable to an already finished table, everything about everything will take no more than one free day.

Conclusion

Now you know what revolving tables are, how they are arranged and how to make them yourself from available materials. If you have any questions, write about it in the comments and do not forget to watch the video in this article.

November 24, 2018

If you want to express gratitude, add a clarification or objection, ask the author something - add a comment or say thanks!

It is very convenient for confectioners involved in the manufacture of cakes to use various kinds of devices that facilitate the process of decorating the finished product. Fortunately, today stores offer a wide range of such inventory. One such device is the turntable. True, the cost of such a table is rather big, and it is often easier and more profitable to try to make a turntable for a cake with your own hands.

What is convenient?

Such a table is useful not only for professional pastry chefs. It will be very useful for those who like to cook for their own pleasure, as well as cooks taking their first steps. By the way, such a table will come in handy for housewives decorating cakes with mastic. It looks like a circle-pedestal on a leg that rotates around its axis. The main goal is to make the work of the confectioner as ergonomic and convenient as possible, to simplify the task of decorating the finished cake. The cake is placed on a stand, and by rotating it, you can easily cover it with mastic, decorate it with figures, inscriptions and other decor. At the same time, you do not need to walk around it, the confectionery will rotate on a stand, and the hostess will have access to any place on the cake.

What will be required

In order to make a turntable for a cake with your own hands, you will need:

• Bearings — 2 pcs. It is better to use double pressed bearings.
• Wooden blank for a circle. This can be a door from old furniture or any chipboard material available.
• Nails.
• Self-tapping screws.
• Tube (made of plastic or iron).
• Iron circle (metal).
• Plywood sheet.
• Plastic or decorative self-adhesive film.

How to make a turntable with your own hands

This process is not too complicated, but requires male participation. To begin with, it is worth drawing a drawing of the future stand and preparing all the necessary elements.

If the bearing is not double, then two will be required, and one must fit into the other.

1. We push the smaller bearing into the larger one using nails.
2. From a chipboard blank (or an old door), we cut out two circles with an electric jigsaw, equal to a diameter of 20 cm.
3. In one of them, a hole should be made in the center into which the bearing is placed. It is this technique that will ensure the turning of the entire mechanism.
4. We attach the second circle with self-tapping screws (you can use liquid nails) to the first.
5. The bottom circle, which does not have a hole, will stand directly on the table.
6. Then a plastic tube is inserted into the bearing (you can use an iron one, if available). It will connect the base and the top - the pedestal for the cake. The tube must fit very precisely into the bearing so that it does not hang out, otherwise it will be difficult to use the turntable. The optimal length of the connecting tube is 15-18 cm. In this case, it will not be too short and too long, it will be most convenient to use the device.
7. The top (the stand itself on which the cake is placed) is best made of metal. You will need a metal circle, which is 30-40 centimeters in diameter. It is attached to the top of the tube (metal or plastic) by welding. Of course, not everyone has a welding machine and a person who knows how to do it at home. In this case, you can use cold welding, reminiscent of plasticine.
8. Plywood or chipboard is attached to the top of the metal circle, equal in diameter to the metal circle, using liquid nails or self-tapping screws.

Now the do-it-yourself cake turntable is almost ready. It remains only to add aesthetics to it. To do this, the top is pasted over with wallpaper-film or a plastic round base. This will give the fixture a finished look and facilitate maintenance.

As you can see, if you want to make a turntable for a cake with your own hands, it’s not so difficult. A set of materials for its assembly can be found in almost any home, and the work process itself is not so complicated.

What can replace the cake turntable

What is the way out for those who do not have a turntable? A very simple and affordable solution is also available in almost any home. You can use a microwave turntable. Almost all models are arranged in such a way that they have a glass plate and a round stand at the bottom. It is necessary to get a plate and a circle under it from the microwave. If it is too smooth, you can put paper (paper towel) down to reduce slip. Thus, you can decorate the cake by smoothly rotating it around the axis. Also, a glass plate will not spoil the view when serving a finished decorated product.