What to remove the old mounting foam. Than you can drop the remnants of the mounting foam from different coatings

To wash the plastic profile from the polyurethane sealer use "White Spirit", wash for mounting pistols or vegetable oil. A pharmacy agent called "Dimeksid" can be useful. To clean the brakes, after repair, you can use vinegar, acetone or scrape the remnants of sealant blade.

It happens that during the installation of windows, the builders are carecriminately stained with polyurethane sealant Plastic window profile, glass or window sill. An annoying accident. To wash the construction foam powders, soap or fairy it is unlikely to succeed, you will spend a lot of time and effort, and the effect will be barely noticeable. Consider the funds that work.

We wash fresh foam

Important! Do not try to remove stains acetone, solvent No. 646 or No. 647, they, of course, dissolve the foam, and at the same time the top coating layer. It is also not worth using the means containing concentrated acids and herds, they will not harm the profile, but they can dissolve the glossy layer, and the plastic will look worse. Hard brushes and cleaning powders scratch plastic, so they are also better not to use.

It so happened that during operation the sealant accidentally hit some surface - you can wash it away at once or wait until it dry. Most often, the dry foamy growth is just enough to pick up the spatula and it will fall off, but if you were lit up to smear the foam throughout the windowsill, it will penetrate into the material and drop it will be very difficult.

If you decide to wash off the fresh seal, then take two spatula in your hands and gently with one spatula, shift a lump of sealant to another. To remove the remaining trace, use one of the funds offered below.

Hot vegetable oil

Heat sunflower or other vegetable oil, moisten the rag and vigorously sweeten the contaminated area. This means is good because it does not have such a sharp smell as chemical. Preparations, cheap and won't hurt household health. Thus, you can wash the wrath of the window, the door, polished furniture, vinyl wallpaper and any other material. The dried traces can also be tried to eliminate butter, but then you need to cover it with rag after applying and leave for 30 minutes, after which you can lose.

Vinegar

Another "homemade" means, which is always at hand. Moisten a napkin in an undiluted vinegar and, making efforts, erase the residues of the seal. A sealant from glass, tile and other smooth surfaces is removed in this way.

Chem. Preparations

Until the process of polymerization of the sealant can be erased, it is possible to erase with a cloth moistened with a "White Spirit" or a liquid for cleaning the ethyl acetate-based mounting pistol. If there is no other on hand at hand, it is better not to touch and not to smear, give foam to dry, then it can be easily considered the blade.

Taking advantage of chemicals, wear rubber gloves and work in a well-ventilated room.

Remove dried sealant

What to drop the mounting foam from the plastic window, if she already dried?

Dimeksid

From the dried sealant, you can easily get rid of the means that the penny is worth and is sold in any pharmacy. It is called "Dimeksid". First you need to gently cut the foam with a knife or blade so as not to scratch the surface. Moisten a cotton disk with Domexide, rub the traces of sealant is richly wetting, put on top of a cotton disk and leave for 5-10 minutes. When the time breaks, the foam softens and will be easily sliding and lagging behind the surface, you just need to lose a little to remove the residues of the foam.

Dimexide can be used on different materials: linoleum, laminate, metal, PVC panels, can be wrapped with clothes wrapped in foam. Single restriction: Dimexid can not be washed with foam wooden windows, and other lacquered surfaces.

Fluid for washing the mounting pistol

Important! When you use solvents or tools for washing the gun, use the white cloth or before washing with colored sponges, napkins or eraser. Check them on color resistance. It is a pity if the flap is polishes, and in the white profile there will be immemorable colored spots.

• Specialties to remove the mounting foam can be purchased in any construction store, the choice is very wide: "Kleo Pro C50", "Reiniger", "Soudal Gun & Foum Cleaner", "Profilux", "Kraftool Krafillex Cleaner", "Cosmofen 10".Before use, read the instructions carefully and just in case, check the tool on the invisible area of \u200b\u200bthe profile. Moisten the rag, pay the spot and rinse this place with a soap solution so that the tool does not run the PVC profile, and at the same time to get rid of the obsessive chemical smell.

When the repair is completed on the windows, furniture and walls, pollution of various origins remain: paints, shplanke, traces of glue, etc. Read by reference.

Secret means of installers

In the most difficult cases, builders use homemade composition. Mix 50 gr. Any fluid for washing assembly pistols, 10 gr. Solvent A-649, as many acetone and 20 gr. acetic essence. It is said that this agent instantly dissolves the sealant of any brand.

Removal of foam from various surfaces

Glass

Fresh sealant from a window or glass furniture can be wiped with a cotton swath in vinegar or "White Spirit". The easiest way to wait for a foam to dry, cut it off by a stationery knife, and the remains of scraping the blade. It is also possible to help gasoline, kerosene, acetone, liquid for removing varnish or any means described above.

Sill

For PVC window sill, you can use the same tools as for the window profile, of course the composition of the plastic may differ and before applying any cleaner it is worth checking its action on the bottom of the windowsill or somewhere on the side.

Wooden window sills can not be washing with liquid for washing pistols, "White-spirit", acetone and solvent, best use vegetable oil.

Window sills and slopes, lined with ceramic tiles can be washed with any means.

Floor coverings

• Carpet Cleans "Dimeksid", gasoline or kerosene.
• Linoleum. If the coating does not have a texture pattern, then the sealant is allowed to dry, and then they just take off. More difficult if there are still pores or an indent ornament. Then it is better to use the "White Spirit" or acetone to clean the cleaning or acetone, it is necessary to apply a tool, and then very carefully planted with a chisel. From linoleum you can remove the sealant with the help of ordinary water, you need to cut off the protruding part of the lump, and put the rest of the wet cloth, after 8-12 hours you can wash the foam.
• Laminate It is easiest to clean with vegetable oil, you can try to use fluid for pistols. Do not clean "Dimeksid", acetone or water (from long contact with water laminate can wake).

Tile

If the foam hit the floor and stained the tile, then it can be laundered by any of the means listed above or linnet with a cotton disk, moistened in vinegar.

Polishing, parquet, tree

Varnish will spoil from contact with solvents and "Dimeksid", so everything that can be done is to try to remove the foam mechanically, and the remains of erased with heated vegetable oil. If it does not help, you will have to come to accept the stain. The same applies to polished furniture, parquet and any painted surfaces.

Fabrics

It's a shame when the fan of the furniture diluted during the repair of the foam. Try not to smear the ball of foam, wait for a complete drying and tear if the cloth with a long pile may have to cut off the lump along with its small part. Smooth surfaces can be laundered by the same gasoline, "dimexide" or kerosene or if the cover is removable, then soak for 12 hours and wash. The same applies to clothing.

In order to clean the plastic windows from the mounting foam, it is recommended to use a special wash for mounting pistols, hot vegetable oil or "White Spirit". In addition, you can use the pharmacy tool "Dimeksid", which is released without a recipe. For cleaning windows after repair work, you can apply a screw tools, including vinegar, acetone, or try to scrape the remaining sealant with a sharp blade. This article will describe in detail all methods for solving the problem of cleaning plastic profiles from the mounting foam.

Repair or construction work are often accompanied by mud, dust and other garbage. There are cases of cases when during the installation of metal-plastic windows builders by negligence packs of polyurethane sealant profile, glass or window sills. Of course, such dirt does not lead to delight. In addition, laundering the mounting foam with a simple soap or detergent will not work. You will only spend time without approaching the desired purity.

In no case, do not attempt to remove stains on profiles using acetone or solvents No. 646 or No. 647. With the help of the tools you can dissolve the stains together with the top layer of coating. The list of non-recommended drugs includes means that contain concentrated acids and alkali. Unlike acetone or solvents, they will not damage profiles, but without difficulty will spoil their glossy layer. Because of this, plastic will lose its commodity look. Hard brushes and cleaning powders also have a negative impact on plastic, scratching the profile surface.

The sealant has already hit the surface. What decision is better to do: wait until it dries or time off it instantly? In most cases, to remove the dry foam growth, you just need to pick it up with a spatula, and it will fall off. The situation under consideration is close to the ideal. Most often you smear the foam throughout the area of \u200b\u200bthe window sill, where it will penetrate the material. In such situations, the sealant is rather difficult.

If you still decided to wash off the recently applied seal, then take two spatula into service. Your task is to gently scrape a foam with one spatula, carrying the assembled sealant to another. After such a procedure, foam particles will remain on the windowsill, which can be removed in the following ways:

First of all, warm the sunflower or any other vegetable oil, moisten the rag. Next, it is necessary to wipe the contaminated surface with this solution. The presented method saves money to buy chemicals that have a sharp smell and negatively affect the human body. With hot oil, you can clean the windows, doors, polished furniture, as well as vinyl wallpapers and other materials. You can also fight dried tracks using oil. To do this, it is necessary to cover the place of contamination with a rag moistened in oil, leaving it for half an hour. After a while you can try to wipe the place of pollution again.

Bite - another people's method in the fight against the installation foam, which is almost always at hand. All that is required of you: Moisten a napkin in undiluted vinegar. After, making efforts, you need to walk along the remnants of the seal. Vinegar perfectly cleans smooth surfaces on the type of glass and tile.

If the process of polymerization sealant is not completed, then try to erase it with a cloth moistened with "White Spirit". An alternative to this medium will serve as a liquid for cleaning the mounting gun based on ethyl acetate. If you do not have any of the voiced funds at your disposal, then simply give foam to dry up, then to get rid of it without any problems by the blade.

Note

When using specialized chemical drugs, do not forget to wear rubber gloves. Work in a well-ventilated room.

We fight with dried sealant

The pharmacy means "Dimeksid", which is selling almost every pharmacy and worthwhile penny will help to get rid of the dried assembly foam. Consider Read more Removal of sealant with "Dimeksid":

The presented solution is used when washed with various materials, including: laminated surfaces, metal, PVC panels, as well as wrapped in assembly foam. There are both restrictions on the use of "Dimeksid": do not wipe the wooden surfaces, since the likelihood of damage to varnish is great.

The principle of operation with a liquid for washing a mounting gun is similar to "Dimeksid", but there is one small exception. It is strongly recommended to use white cloth or color-resistant sponges and napkins. Otherwise, when laundering a profile, colored spots from the fabric can remain. Check the tools for washing on color resistance can be used with elasty.

Special means

Special remedies for laundering sealant sold in construction stores. The range of products offered is wide, so consult with the seller before buying a product. Do not forget to test the effect of the means before it is applied.

Secrets of professional installers

We bring to your attention a recipe for a self-made solution, which will help get rid of the mounting foam. Professionals say that this solution is capable of instantly dissolve the remedy from any manufacturer.

• Take 50 grams of fluid, which is used to wash the mounting pistols, 20 grams of acetic liquid, 10 grams of solvent "A-649", 10 grams of acetone.
• Mix all the ingredients.

Tile

The tile is a surface that can be washed in any way. Starting from folk methods (bite, oil) and ending with professional means ("White spirit", solvent, gasoline, etc.).

Fresh sealant is unhindered removed by means of a mock moistened in vinegar or "White Spirit". However, as stated earlier, it is much easier to wait until the foam dries. The protruding part is cut off with a knife, and the remnants of scraping the blade. An alternative will serve all other funds previously described.

PVC window sills are cleaned by a principle similar to glass structures. Of course, the composition of the plastic is differ from the glass, so in front of any "experiment" test the impact of the solution on the bottom of the windowsill or side. Window sills and slopes, lined with ceramic tiles, are laundered without problems with any voiced detergent.

The window sills made of wood are forbidden to wash off the liquid for washing pistols, acetone, solvents or means called "White Spirit". In such cases, vegetable oil will be an excellent alternative.

Polishing, parquet, tree

The main difficulty when washing the wood or parquet is varnish, which, when contacting most of the means, is spoiled. Options remain a bit, and they will not always show 100% efficiency. Try to get rid of the top layer of foam mechanically, and removes remove with vegetable oil.

Fabrics

Blurred upholstery of furniture? First of all, try not to smear the foam. Wait for a complete drying of the sealant, and then remove it from the surface of the fabric. If the foam fell on a long pile, then you will have to cut off a lump along with a small part of the tissue.

In case the sealant hit the smooth fabric, then gasoline will help you, "Dimeksid" or kerosene. If the mounting foam hit a removable case, then it will be necessary to soak it for 12 hours. Such operations are carried out with clothing.

Most exterior and internal construction work at home or repair require the use of mounting foam. Without it, it is difficult to introduce the installation of windows and doors, insulation and sinking siding, work on pipe wiring. Foam firmly fixes individual elements and also firmly sticks to the surfaces on which it should not be.

Ideally, all the stupid work should be carried out so that it does not oppose emptiness and, moreover, did not fall into open areas. But the troubles happen even with professional masters, not to mention home crafts, which are often taken for repairs for the first time. So how and what to wash the mounting foam?

Fresh foam

Fresh foam is removed easier. Immediately it must be assembled (only not with bare hands!), Plastic or other, not scratching the surface, the scraper to maximize, not swinging. Then take advantage of the rigid cloth or sponge and solvent, depending on the type of coating. The following substances have proven themselves most well.

• The most affordable option is acetone or solvent 646. However, these funds are not suitable for vinyl siding or plastic lining, the surface of which will simply get out of such aggressive substances.
• Isofoam R621 is a special means of Russian production for washing, but copes with foam and on other surfaces. The bottle of 600 ml costs less than 100 rubles.
• Cosmofen is a favorite tool of masters setting windows. There are three species of Cosmofen 5, 10 and 20. "5" - the strongest, "20" is weak. Suitable for removing foam with plastic and glass. Minus - sold in bottles one liter, so it is not the cheapest option for cleaning a small area.
• Washing Macroflex well softens foam and makes her further rubbing simple.

Before applying the solvent, check on an inconspicuous area, whether it does not take place the top layer of coating.

Frozen foam

If the fresh foam is not so difficult, it is tightly climbing and yellowed - very problematic. The main component you need to stock up is patience. From the first time, the material may not be laundered without a trace, the procedure will have to repeat several times.

It is relatively simple to remove the frozen foam from glass, metal, stone or tiles. First of all, you need a construction knife or a new blade from a dangerous razor to cut a layer of foam as close to the surface, trying not to scratch it and do not cut your hands. When the thin layer of substance remains, it is necessary, first, to twist it with a solvent, and then with the help of a rigid sponge to lose.

The sponge is needed that the metal grid used for the same purpose is used to wash pan and steel saucepan. As a solvent, Soudal PU Remover has proven itself, designed to remove precisely frozen foam.

Another way is a simple mechanical rubbing with a smooth piece of plastic (or other material that is hard foam, but softer surface purified). Covered battery enamel, powder coated metal doors are better so.

Delicate surfaces

To clean the plastic, wood covered with varnish, linoleum use aggressive solvents can not be used, since not only the foam will wash, but also the top coating layer.

Verified folk remedy for removing the mounting foam - Dimexide. It is sold at the pharmacy, it is a penny and is designed to reduce inflammation in the joints and increase the permeability of the skin. Dimethyl sulfoxide, this chemical name, in fact, is a powerful solvent and is able to penetrate into the large number of organic matter.

In order to wash the foam, you need to use an undiluted with a rigid rigid or sponge, showing spots for a few minutes. If the stains are small, you can use a cotton wand. It is necessary to work with Dimeksidally in dense gloves, and, as using any solvent, check its effect at the invisible area of \u200b\u200bthe coating. After processing, the cleaning surface must be wiped with a wet cloth.

Leather and fabric

From the hands and other parts of the body, the mounting foam is removed with difficulty. Be sure to do it immediately, without waiting for the seizure. It is necessary to remove as many foam as possible mechanically, for example, remove with paper or napkin, and then use the solvent safe for the skin. The same acetone is suitable or even a liquid for removing varnish, the hands from them, of course, dried, but it is fixed later with a nutrient cream.

If you failed to fully believe, you should not worry - the skin is updated daily, and sooner or later, all traces will absolutely disappear. You can help this process, it is more often with a washcloth in this place and lubricating it with a bold cream.

In the case when foam hit clothes, the likelihood of whether it is beaten, depends on the structure of the tissue. From knitwear and knitted things it is almost impossible to consider it. To consider foam with jeans, leather and leatherette, you can use the same means as to remove an unrestal material, you can try to treat the spir-spirit spot.

Clear the mounting foam is not easy. The one who had to come across this, next time he definitely protects his hands and all around from her hit. It is easy to do that, the foam does not close with the polyethylene film and silicone, so the adjacent surfaces must be closed with a film or lubricate with silicone oil, and work only in gloves.

Without a mounting foam, almost no type of construction work costs. With it, they close the slits, fill the window and doorways, glue some kinds of products, perform a lot of other useful actions. In the process of work, it is very rare to do without a sticky content of the cylinder on various types of surfaces in close proximity, as well as on and clothing. The main question of this article is how to clean the mounting foam in a liquid or solidified state.

Mounting foam refers to substances, the removal of which causes certain difficulties. More recently, acetone was considered the only cleansing agent. Now there are many alternative cleaning methods that we will analyze in this material. On different materials, foam acts in different ways, so it is necessary to apply various means selectively.

We list the funds, with which you can fight with traces of mounting foam:

Tip: If you decide to apply some kind of tool for cleansing foam, treat them at the beginning of a small area. If no consequences for the surface are, you can use this tool for complete cleaning.

Purification of foam from various surfaces

Liberation of the gun from foam residues

After the end of work, if a gun was used, polyurethane foam particles remained. How to clean the gun from the mounting foam? This can be done in two ways:

• Mechanical cleaning. With the help of a knife, a flat screwdriver or sewed remnants of the frozen composition;
• Chemical cleaning. To do this, the pistol is inserted with a foam solvent cylinder. For example, Penosil or OPPA. After that, press the trigger, while the gun will not go out of the gun.

After such a cleaning, the device will restore its performance.

Note: For liquid and already frozen foam, there are different types of solvents. Each of them is better coping with a certain composition of the substance.

Cleaning PVC windows or doors

What to drop the mounting foam from the plastic window or the same door? Polyvinyl chloride reacts negatively to severe solvents, especially containing acetone. As a result of interaction with the surface of PVC, spots may appear on the surface of the material, which will be impossible to remove.

From the PVC windows, the foam is removed elementary. In the frozen form, it is easy to consider a plastic scraper or a piece of wood. Traces usually do not remain. You can also use vegetable oil, which is applied to traces and is withstanding for 30 minutes. After that, pollution is easily laundered with a wet sponge or the same scraper.

Cleaning wooden doors and windows

As a rule, wooden doors and windows are covered with varnish or paint for better protection and aesthetics. How to wash the mounting foam with painted or lacquered doors? Apply traditional cleaners are not always recommended not to damage the smooth surface.

It follows in a glass of ordinary water to dissolve a tablespoon of the cooking salt, after which the contaminated area is treated with solution. After 5 minutes you need to wipe the surface with a damp kitchen sponge.

Purification of metal surfaces

Do not know what to rain the mounting foam with a metal door? The main mass is cut, and then the contaminated metal is wetted with sunflower oil. It is withstanding 30 minutes, after which the remnants of pollution are removed by any cloth or sponge. The place of exposure to oil is washed with soap solution to remove fat traces.

Removal of pollution from glasses

From the glass, the composition is removed only when it completely freezes. With a sharp knife or blade, the composition scrapes with glasses without consequences. There is no tracks on the glasses. If there are some opaque areas, you can use the usual fluid for removing the nail varnish or other solvent.

Cleaning floor coatings

Linoleum

The foam is not absorbed into the surface, so it is possible to delete it very simply. To do this, wait until the composition freezes, and then cut off its main mass. Some traces will definitely remain. They can be removed by a special cleaner that does not contain acetone or dimexide. Note that after using acetone on the surface of the linoleum, matte spots may remain.

Carpets

What can be cleaned by the mounting foam with soft flooring to do without cutting a pile? The best option will be the use of ordinary water. The foam is well associated with a pile, so immediately remove it with a solvent is meaningless. On the rest of the foam you need to put a rag moistened with water. After a few hours the composition will soften, and it can be removed without any problems with a brush or spatula.

Laminate

Contaminated areas need to be treated with a special cleaner or dimexide. After the destruction of the composition of the foam, it will be easy to remove it with a piece of fabric or.

Parquet and parquet board

If the foam is fresh, it is recommended to apply one of the cleansing means if it is on hand. And what to wash the dried assembly foam? First you need to cut the main frozen mass. After that, use a solution of dimexide, gently applies it to a contaminated surface using a brush or cloth. After 15 minutes, the foam collapses, and it can be easily removed with a rigid sponge used for washing dishes.

Wood

Apply special cleansing formulations or demikid. These substances can penetrate deeply in the pores of wood, destroying the particles of foam. An hour later, using the brush, the surface is cleaned from extraneous elements. In the same way, it is possible to resolve the question of how to remove the mounting foam from the door or windows, which are wooden products.

Important: It is necessary to very carefully use the potent compositions on the lacquered surfaces, as they can cause the layer removal of the varnish coating and the appearance of spots.

If, after applying solvents, the traces of pollution are still visible, it remains such a radical solution as grinding the surface by sandpaper or grinding disk.

Cleaning clothing

The question of how to clean the assembly foam from clothing, relevant to many people, because clothing is most often contaminated.

Fully removed from the tissue foam almost unrealistic, as it is very firmly associated with the fibers. However, it is noticeable to reduce its influence on the fabric you can try. Immediately it is worth saying that substances containing acetone are better not to use, as acetone is able to change the color of clothing, and even spoil it.

How to drop the assembly foam that fell on clothes? For this, the following options will be suitable:

• white Spirit;
• stain remover;
• gasoline solvent. This is pure gasoline that does not contain impurities. It is necessary that you need to use;
• foam solvent.

Now consider, nothing to wash the mounting foam from clothes, but as:

1. From the surface of the fabric, the foam cap (fresh or already frozen) is removed.
2. One of the above compositions is applied to the fan.
3. It is withstanding a pause of 15 minutes.
4. The remains of the substance are removed by a cloth, a sponge or soft brush.
5. If traces of foam remained on the fabric, the procedure can be repeated.
6. Clothes are washed using powder and stain pressure.

Use the freezer

This method can help if there are separate splashes of foam composition, as well as when foam in delicate tissue getting.

Do not know how to remove the mounting foam from clothes without the use of solvents? We tell:

1. The contaminated thing needs to be folded into the plastic bag, and the package is to be put into the freezing chamber.
2. After 1 hour, clothes should be removed from the freezer, and the pieces of frozen foam remove with the tissue with their hands.
3. If the stains remained, they can be treated with a stain remover.
4. Clothes must be wrapped.

It is easier to prevent the occurrence of trouble with foam, rather than eliminate the consequences of such errors. However, using one of the above methods, you can completely or partially eliminate pollution.

Tweet

Almost all construction work implies the use of mounting foam. It reliably fixes the elements, tightly adjacent to the surfaces. Its use requires maximum accuracy, but sometimes it does not fall there, where necessary, even in the hands of professionals. You can wash the mounting foam from any surface, but each of them has its own features of cleaning. There is also a difference in the removal of fresh and old sackes.

The easiest way is to remove fresh foam from most surfaces. While she did not have time to frozen, it is very easy to assemble. The main thing is to do it in gloves to avoid sticking to the hands. The optimal option will be the use of a plastic subject, which will be able to collect all the remains, without a scratching of the surface. The last stroke in the cleaning of the non-frozen foam will be the use of special tools for washing with a soft cloth.

It is advisable to choose one of the following (choose the type of surface):

• Acetone;
• ISOFOAM R621;
• Cosmofen;
• Macroflex.

To avoid damage to the surface on which foam got, it is possible to pre-check its reaction to the cleaning agent. To do this, it is enough to apply a small amount of substance to a very small imperceptible area to be used to remove.

Dried traces

After completing the part of the construction work, time to check whether there are no traces of the materials used somewhere, it remains. As a result, people get dried foam in the most unexpected places. It is more difficult to wash it out, but from some surfaces it is better to clean it in a dried form.

As a rule, first cut off the main part of the dried piece. Then use special means (for example, dimexide), with which they rub the remnants of traces. Sometimes tritely use solar light power, because Rays destroy the structure of frozen foam pieces, but it requires a lot of time.

Mounting pistol

After pouring the foam in all the necessary places in the gun there may be its particles that soon dried. The earlier a person notices her traces, the easier it will be clear the construction device.

How to Clean the Pistol:

1. Check if foam managed to dry. If it is still soft, then the gun needs to rinse with the ISOFOAM R cleaner
2. When she managed to frost, you need to either consider the remnants with a screwdriver, or use the solvent (OPPA or Penosil).

After cleaning the gun will work again. The main thing is to clean carefully, especially if you use a screwdriver and other items for mechanical cleaning.

Hands

Very often suffer from the "installation" of the hands. Wash it off the skin more difficult. In such cases, it will not be possible to take advantage of the majority of specialized chemicals that would help solve the problem. But we will help usual everyday means and folk methods.

Ways to remove material from hand:

1. Baths with soap or salt. If she did not have time to dry out, it is easiest to get rid of it with aqueous solutions. You can hold hands in warm water with the addition of either two pinch of salt, or a small amount of soap.
2. Cosmetics. The problem area of \u200b\u200bthe skin is needed to be well lubricated with fatty cream or butter and wait 20 minutes. Then the residues need to slowly remove, without damaging the skin.
3. Vegetable oil. It is necessary to warm up and apply on the skin, sprinkle a little washing powder from above, bold and washed. After that, it is recommended to thoroughly wash your hands with soap.
4. Alcohol, vinegar, gasoline, acetone, kerosene. Any of the listed means helps to destroy the structure of dried foam. They need to moisten a cotton disk, and then wipe the problem plot well. In the end, it will remain only a few times to wash your hands.

After performing all the procedures, the hands should be washed with a gentle soap and lubricate with children's cream.

clothing

Avoid building materials on clothing during repair is almost unrealistic. And clean the fabric surfaces the most difficult. But the mounting foam launder from the clothes will still succeed. Make it is not easy, because From many funds, even working suit can be spoiled. It is important to check in advance, as it affects or another substance to avoid bleaching and damage.

How to remove foam from clothes:

1. Cut the main part of the dried matter, trying not to damage the fabric. An ordinary knife is perfect.
2. Mix the rag with a substance that can destroy the structure of the foam. A solvent in the form of gasoline (White spirit), pure gasoline, dimexide or acetone is suitable. The rag is simply attached to the place that is contaminated for a few minutes.
3. Wash clothes in a classic way. It is necessary to do this only after removing all foam traces.

Doors

Another place that often suffers when repairing is the door. It will be not easy to clean it. To remove the remnants of the foam with the door you need to do the most carefully so as not to spoil her appearance. The cleaning method will depend on what material it is produced. If from the tree, then everything will be quite simple, and in the case of the metal you have to make much more effort.

How to wash tracks from a wooden door:

1. Cut the sharp knife as much foam as possible.
2. Carefully clean the remaining traces using sandpaper.
3. Cover the place where cleaning occurred, if necessary.

How to wash tracks from a metal door:

1. Cut the entire main part of the foam using an acute subject.
2. Mocked a large sponge with vegetable oil, apply it to a problem area in large quantities.
3. You need to gently rub the remaining pieces, trying not to damage the doors.

After performing all the procedures, the doors should be washed with warm water with soap. In the second case, it is simply necessary, since the oil stain will remain on the surface, striking.

Removal of "Installation" with a different kind of doors - Video:

Plastic windows and panels

Color traces of the mounting foam sometimes fall after installing plastic windows. Wine inexperienced masters who perform work. Traces on glass or panels are very noticeable and spoiled the appearance of the room. And get rid of them quite difficult. But if I had to face such a problem, you should not despair.

How to erase traces from plastic or glass:

1. Cut the maximum possible amount of foam using a knife or other acute item, trying not to cause surface damage.
2. Mix the residues to dimexide or use the means for removing foam from solid surfaces. In the case of a fresh spot, you can apply oil, acetone, vinegar. You need to do everything with neat movements on a problem area.
3. Leave the substance for a few minutes so that the foam structure can collapse.
4. Wipe the rigid sponge the entire area by removing the last traces.
5. Wash with a clean sponge with soap or special means the entire processed area and wipe it well with a gentle towel.

When processing various substances, plastic and glass surfaces, maximum caution should be exercised so as not to harm their appearance.

Floor coverings

Mounting foam on the floor - the most frequent phenomenon in the repair. Loose its traces on floor coverings rather not easy. The tool that will be used for this will depend on the type of floor material.

Coating and cleaning method:

1. Linoleum. This material does not absorb foam, because of what the removal process does not take away a lot of time. It is only necessary to wait drying, cut off the basis of the solidified piece, and then dissolve the remnants of the dimexide, which must be applied to the desired area for 15 minutes. After cleaning, it is recommended to wash this place with soapy solution.
2. Parquet. The process of cleaning is the same as in the case of linoleum. The only difference is that the parquet can be washed from fresh foam. To do this, it is enough to clean the plot with ordinary cleaning agents.
3. Carpets. The substance is tightly bonded with Villas, which will have to wait for its solidification. When she dries, you need to throw a raw rag from above. After a few hours, the rag can be washed, and the traces of the foam are cleaned with a brush.
4. Laminate. Removal from laminate occurs quickly and simple. As in the case of a linoleum, you need to wait for drying, and then produce processing with dimexide and after a while wash all the remains of the sponge.
5. Wood . Foam can penetrate inside wooden surfaces, which significantly complicates the situation. However, Dimekside also has such properties, due to which it easily eliminates the residues of any substances. You need to apply it to a problem space for one hour, and then erase with a sponge or brush and wash.

Remove the mounting foam from a different kind of coatings - Video:

After fulfilling all procedures for cleaning the floor, the floor should be well wash and give it to dry.

Conclusion

Mounting foam is not as terrible, as it may seem at first glance. Wherever she fell, it can be quite quickly destroyed with special means. The main thing, do everything neatly.